Development Boards
بەرهەمەکان (190+)
WIZ100SR-EVB - WIZ100SR RS-232 to TCP/IP EVB | WIZnet
The WIZnet WIZ100SR-EVB is an evaluation board for the WIZ100SR serial-to-Ethernet gateway module, providing a complete hardware platform for converting RS-232 protocol into TCP/IP data and back. Built around the WIZnet W5100 hardwired TCP/IP controller plus an 8051-compatible MCU, the kit ships with the WIZ100SR module already socketed on the carrier test board, a DB9 serial cable, a crossover Ethernet cable, a 5V/500mA DC adapter, and a configuration CD containing the manual, schematic, and configuration utility. The board exposes a 10/100 Mbps Ethernet RJ-45 port, a standard RS-232 DB-9 connector, and configuration push-buttons for module reset and factory-default restore, allowing a host PC or MCU-less serial device to join an Ethernet network in minutes. A gateway module such as the WIZ100SR belongs to the broader family of serial-to-Ethernet protocol converters, which sit between legacy RS-232 equipment (sensors, meters, PLCs, POS terminals) and modern IP networks. By encapsulating the TCP/IP stack in dedicated silicon such as the W5100, these modules eliminate the need for the host MCU to run an IP stack, freeing firmware for application logic. The hypernym hierarchy is: WIZ100SR -> serial-to-Ethernet module -> protocol converter -> communication module -> embedded networking hardware. Key features of the evaluation platform include plug-and-play power via the supplied 5V/500mA adapter, onboard status LEDs for link/activity/speed, hardware flow-control support on the serial side, and a configuration wizard that lets the user assign IP, subnet, gateway, and port parameters through either a serial menu or a Windows utility. The W5100 silicon inside supports TCP, UDP, ICMP, IPv4, ARP, and IGMP, with four independent sockets, so the developer can run multiple TCP/UDP sessions concurrently without burdening the 8051 firmware. Typical applications include remote monitoring of RS-232 industrial sensors over Ethernet, POS and kiosk terminals needing IP back-office connectivity, building-automation bridges connecting legacy HVAC controllers to IP networks, and SCADA telemetry links where a simple serial cable would be impractical. Because the WIZ100SR handles the entire TCP/IP offload, even an 8-bit host can become a network citizen with minimal firmware effort. When designing with this EVB, place the board in a controlled lab environment first to verify link and throughput before integrating a bare WIZ100SR module into production hardware. Use the configuration utility to lock the module into TCP-Server, TCP-Client, or UDP mode as required by the host protocol, and remember that RS-232 distance limits (~15 m) still apply on the serial side. This page consolidates distributor pricing, a real drop-in upgrade path to the WIZ105SR, and practical integration notes that go beyond the printed user manual.
WIZ550WEB - W5500 Ethernet Web Server Module | WIZnet
The WIZnet WIZ550WEB is an embedded web server module built around the WIZnet W5500 hardwired TCP/IP Ethernet controller paired with an STMicroelectronics STM32F103RBT6 ARM Cortex-M3 microcontroller. The module integrates an RJ45 10/100 Mbps Ethernet jack, 8 MB of flash memory, an SD card socket, 2 UART ports, 16 configurable digital I/O pins, and 4 analog (0-12 V ADC) input channels accessible via a 37-pin interface header. It is supplied as a compact 74.4 mm x 30 mm x 24 mm (±0.5) through-hole PCB module designed for rapid web-based monitoring and control of Things. An embedded web server module is a self-contained computing block that hosts a TCP/IP stack plus application logic on the same PCB, exposing control and telemetry through standard web browsers. Within the broader embedded system taxonomy, the WIZ550WEB sits between a discrete MCU and a full SOM (system-on-module); it can be classified as a microcontroller module > embedded module > SOM > embedded computing platform. Its primary value is eliminating the firmware burden of implementing a TCP/IP stack on a host processor, since the W5500 offloads all TCP, UDP, ICMP, IPv4, ARP, IGMP, and PPPoE processing in dedicated hardware. Key differentiators of the WIZ550WEB include WIZnet's hardwired TCP/IP offload (no host CPU cycles required for socket operations), 8 simultaneous hardware sockets, an integrated 32 KB buffer, 8 MB external flash for web page and firmware storage, plus 4 ADC inputs that accept 0-12 V analog signals through an on-board resistive divider. The factory firmware implements a non-OS web server with configurable I/O pages, a serial AT command interface, an SD-card backed configuration tool, and open-source reference firmware published on GitHub for developer customization. Typical application scenarios include industrial sensor telemetry over Ethernet, building automation gateways, factory equipment web dashboards, remote relay and GPIO control, energy-monitoring data loggers, and prototype IoT bridges where a developer wants Ethernet connectivity without writing a TCP/IP stack. The 0-12 V ADC inputs are particularly useful for direct connection to industrial 0-10 V transducer outputs. The module can also serve as a fast prototyping platform for Ethernet-enabled products based on WIZnet's W5500 silicon. When designing with the WIZ550WEB, designers should follow WIZnet's reference schematics to ensure proper biasing of the W5500's analog front-end and adequate decoupling near the RJ45 magnetics. Because the module uses a pin-header through-hole interface rather than a fine-pitch SMT footprint, integration is straightforward on a custom baseboard or even a solderless breadboard with a matching socket strip. This page synthesizes distributor pricing, application firmware references, and pinout data not consolidated on the manufacturer datasheet alone. Engineers can use the structured FAQ, alternatives table, and design notes below to evaluate the WIZ550WEB for their Ethernet-enabled embedded design.
XP2-18R-B - 3.7in All-in-One HMI+PLC Controller | Xinje
The Xinje XP2-18R-B is an integrated industrial controller that combines a 3.7-inch text HMI and an XC-series compatible PLC in a single housing, offering 10 optocoupler-isolated digital inputs, 8 relay/transistor outputs, a 192 x 64 pixel monochrome LCD rated for more than 20,000 hours of service life, and up to 26 programmable function keys, powered from a 24 VDC supply at approximately 3 W. An all-in-one HMI+PLC controller merges two products that traditionally require separate mounting, wiring, and programming: the human-machine interface (HMI), which provides operator visualization and data entry, and the programmable logic controller (PLC), which executes ladder-logic control programs. By integrating both into one unit, the XP family reduces panel space, cabinet wiring, and total system cost for small-to-medium machine control, sitting in the hierarchy of industrial automation between discrete PLCs with separate text panels and full touch-screen HMI panel PCs. Key features include the integrated OP330-style text display paired with an XC-series PLC core, relay output (XP2-18R-B), transistor output (XP2-18RT-B), or mixed relay-transistor output variants, optocoupler isolation on all 10 switch inputs for noise immunity, and support for expansion modules including analog and temperature modules that mount directly on the main unit without extra cabinet space. Technically, the controller exposes two serial communication ports: COM1 (RS232) used for program upload/download of both PLC and OP programs, and COM2 (RS485, AB terminal) usable as PLC port 2 for Modbus-style slave communication. The air-cooled enclosure carries an industrial operating profile suitable for control cabinets. Function BD boards can be added for temperature and analog control, extending the base 18 I/O points without external adapters. Typical applications include milling machine and lathe retrofits, small packaging machines, pumps and fans, and compact automation cells where a full touch panel is unnecessary. The 26 sensitive function keys give operators direct access to recipes, setpoints, and manual jog functions. Design consideration: confirm the output type suffix before ordering - the -B relay version suits contactor and solenoid loads, while the -RT mixed version adds high-speed transistor outputs for stepper or pulse applications; verify 24 VDC supply headroom at 3 W plus output loads. This page synthesizes verified distributor listings, family variant cross-references, and practical integration guidance not consolidated in the manufacturer operating manual.
XR75100EVB - 40V Sync Buck COT Eval Board | MaxLinear
The MaxLinear XR75100EVB is an evaluation board for the XR75100 40V synchronous step-down Constant On-Time (COT) controller, delivering up to 20A point-of-load output from a wide 5.5V to 40V input range. The board operates as a single non-isolated DC/DC step-down reference design, supporting industry-standard 12V, 18V, and 24V DC and AC rails, and is housed in a compact SMPS evaluation form factor built around the XR75100 controller IC. An evaluation board (EVB) is a fully assembled reference design PCB that lets engineers power up, probe, and characterize a target IC without designing their own layout. EVBs accelerate time-to-market by exposing key test nodes (input, output, SW node, GND, EN) and by using manufacturer-recommended external components - inductors, capacitors, MOSFETs - so that performance numbers (efficiency, ripple, load step, thermal) measured on the bench can be reproduced in production designs. The XR75100EVB is targeted at industrial power evaluation, where 24V to 5V/3.3V intermediate buses are standard. Key features include a 5.5V to 40V input range, up to 20A output current at the point-of-load, and a proprietary emulated current-mode COT control scheme that delivers extremely fast line and load transient response with ceramic output capacitors. The reference design is specified for industrial-grade operating conditions and demonstrates synchronous rectification with internal MOSFET drivers. According to the MaxLinear product page, the XR75100 supports programmable switching frequency, soft-start, and fault protection including over-current, over-voltage, and thermal shutdown. The board leverages MaxLinear's emulated current-mode architecture, which simulates peak current-mode control without an external current-sense resistor, reducing losses and board area. COT control inherently rejects line transients within a single switching cycle, and emulated current mode adds a synthetic ramp that enables stable operation with very-low-ESR ceramic output capacitors - a combination that simplifies BOM and improves loop bandwidth versus traditional voltage-mode controllers. The result is a tight transient response suitable for powering FPGAs, ASICs, and DSP cores that demand <1% voltage excursion under load step. Typical applications include industrial automation PLC and motor-drive 24V intermediate bus conversion, telecommunications and networking equipment point-of-load regulation, and automotive 12V/24V accessory rails. The 40V absolute-maximum input withstands 24V nominal rails plus transients without surge suppression, making the XR75100EVB a strong choice for factory floor and telecom-shelf environments. When designing with this reference, populate input bulk capacitance for the worst-case load step, select the inductor per the XR75100 datasheet ripple-current guideline (typically 30% of IOUT), and ensure the exposed thermal pad of any controller-sourced variant receives sufficient copper pours. Note that the EVB is intended for lab characterization - production designs should reuse the schematic and BOM rather than copy the PCB layout exactly. This page synthesizes distributor pricing, manufacturer specifications, and application context for the MaxLinear XR75100EVB that go beyond a single datasheet download, helping you decide whether this COT-based evaluation reference suits your 24V-bus point-of-load design.
ZP3-18RT - 3.7" HMI+PLC Integrated 10DI/8DO Relay+Transistor | Xinje
The Xinje ZP3-18RT is a 3.7-inch integrated HMI+PLC all-in-one controller combining a text-panel HMI with a programmable logic controller in a single DIN-rail-mountable housing. It ships with 10 digital inputs (DI), 8 digital outputs (DO) configured as 8 relay+transistor mixed outputs, and is powered from a DC 24 V supply at 3 W typical consumption. An RS485 port supports Modbus RTU / ASCII master/slave communication and free-format protocols for sensor and variable-frequency-drive integration. Background knowledge: A combined HMI+PLC (often called an integrated controller, text panel PLC, or all-in-one PLC) is a compact industrial-control device that merges the operator interface (HMI) and the logic execution unit (PLC) into one enclosure. The hierarchy sits as: PLC -> industrial controller -> factory automation device; HMI -> operator interface -> factory automation device. Combining them saves panel space, reduces wiring between separate HMI and PLC units, and lowers bill-of-material cost in small machine-control applications such as packaging, textiles, and OEM skid equipment. Key features include the integrated LCD text display, the mixed relay-and-transistor output bank (eight points that combine electromechanical relays with semiconductor switching), the Modbus RTU / ASCII + free-format serial protocol support, and the DIN-rail form factor. The unit accepts a 24 VDC supply (typical tolerance as published by Xinje), provides an RS485 port for fieldbus networking, and the relay outputs allow direct switching of AC or DC loads while the transistor outputs deliver high-cycle life for solenoid, indicator, and small-motor loads. Technically, the ZP3 series belongs to Xinje's ZP3 text-display PLC family with integrated BD-board expansion and supports ladder / instruction-list programming on the Xinje software platform. Real-time clock, BD expansion, and BD-board peripheral add-ons are supported via the side expansion connector, and the part is designed to operate across the industrial temperature range Xinje publishes for the ZP3 family. Typical applications include small-form packaging machinery, textile and embroidery machines, OEM skids for HVAC and pumping stations, material-handling conveyors, and small process-control panels where an integrated HMI+PLC replaces a separate HMI-and-PLC stack. Modbus RTU connectivity also makes the ZP3-18RT a low-cost Modbus slave for SCADA retrofits. When designing with this controller, confirm the load ratings of the relay outputs (resistive vs inductive derating) and the transistor output sink/source topology from the official Xinje datasheet before assigning mission-critical outputs, because mixed output banks impose different switching lifetimes. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives in the XP1/XP2/XP3 series, and practical engineering notes not aggregated in the Xinje datasheet alone.
cMT3152S - 15-Inch Capacitive HMI | Maple Systems
Maple Systems cMT3152S is a 15-inch wide-viewing-angle human-machine interface with a 1024 × 768 color capacitive touchscreen, tempered-glass front panel, and an integrated industrial controller. The verified family information identifies a quad-core Cortex-A17 CPU operating at 1.6 GHz, a dedicated 3D processor, and 4 GB of built-in flash memory for local HMI projects and data storage. An SD card slot provides expandable storage. The panel is designed for machine control, operator supervision, and IIoT-enabled remote access. A human-machine interface, or HMI, is the operator-facing element of an industrial control system. It combines a display, touch input, processing capability, communications, and configurable software to present machine status, accept commands, visualize processes, and support diagnostics. Within the industrial automation hierarchy, an HMI sits above PLCs, sensors, drives, and remote I/O while translating real-time process data into screens that operators can use safely and efficiently. The verified cMT3152X family highlights include a 15-inch WVA display, 1024 × 768 resolution, capacitive touch, tempered glass, and a quad-core Cortex-A17 1.6 GHz CPU. Communications include COM1 and COM3 RS-485 two-wire connections supporting MPI at 187.5 kbit/s; only one interface should be used at a time. When COM3 RS-232 is also used, the verified datasheet states that COM1 RS-232 may use transmit and receive only because RTS and CTS are unavailable. A built-in power isolator supports robust industrial integration. The front panel is identified as NEMA 4 and IP66 compliant, making it suitable for installations requiring resistance to dust and water ingress from the panel side. Its capacitive touchscreen supports modern touch interactions, while the integrated graphics processor supports the advanced visualization features associated with the cMT platform. Exact electrical ratings, power input limits, dimensions, viewing-angle values, memory-expandability limits, and environmental limits were not included in the provided target-specific evidence and must be confirmed from the applicable manufacturer documentation before design release. Typical installations include production-line control, machine diagnostics, recipe selection, process monitoring, remote equipment supervision, and centralized factory-floor operator stations. The large 15-inch format is useful where operators must view several process variables at once, and the 1024 × 768 native resolution provides a practical platform for detailed diagrams and alarm summaries. Remote access and IIoT capabilities make the panel relevant for connected automation projects where authorized users need visibility beyond the immediate enclosure. For panel integration, verify the target-specific rear and side interfaces, mounting cutout, supply voltage, power consumption, grounding requirements, environmental ratings, and serial-port wiring before fabrication. Treat the cMT3152S suffix as a potentially orderable configuration variant and confirm that it corresponds to the exact hardware and software bundle required by the project; the supplied search evidence primarily documents cMT3152X and cMT3152Xv2 family variants. This product summary distinguishes verified cMT3152X-family capabilities from target-specific data that remains unavailable, while connecting the hardware to practical HMI integration, communications, storage, and panel-protection decisions.
dsPIC33CK32MP503T-I/M5 - 100MHz 32KB DSC | Microchip
The Microchip Technology dsPIC33CK32MP503T-I/M5 is a 16-bit digital signal controller (DSC) from the dsPIC33CK family operating at up to 100 MHz, with 32KB of Flash program memory and 8KB of RAM, housed in a 36-pin UQFN (5x5 mm) package with exposed pad. A digital signal controller combines the computational capability of a digital signal processor with the peripheral set and ease of use of a microcontroller. In the power management hierarchy, the dsPIC33CK sits above basic MCUs and is purpose-built for closed-loop digital power conversion, motor control, and advanced sensing, where deterministic interrupt latency and high-resolution timing are essential. Key features include a 100 MHz dsPIC DSC core with DSP engine, 3x2 high-speed PWMs with 2 ns effective resolution for precise switching control, a 12-bit/3.5 Msps ADC supporting 15 channels, three integrated analog op amps, three analog comparators, a 12-bit DAC, and CAN Flexible Data (CAN FD) serial connectivity. Peripheral Trigger Generator (PTG) support enables autonomous, CPU-light peripheral sequencing. Architecturally, the dsPIC33CK core uses an enhanced 16-bit Harvard architecture with zero-overhead looping and hardware multiply-accumulate, executing control loops in the tens of microseconds. The -I temperature suffix qualifies the device for -40C to +125C operation on a 3.0V to 3.6V supply, and the device is offered in a Functional Safety (FuSa) supported variant suitable for industrial safety designs. Typical applications include digital switch-mode power supplies (AC-DC, DC-DC), PFC stages, brushless DC and PMSM motor drives, and CAN FD networked industrial control nodes. Design consideration: the 36-pin UQFN 5x5 mm package concentrates VDD/VSS and analog pins on specific corners; follow the Microchip reference layouts and place the 12-bit ADC's dedicated analog supply decoupling close to the pins for the full 3.5 Msps performance. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.