بەرهەمەکان (1,300+)

DSPIC33CK64MP102-I/SS - 100MHz 64KB DSC 28-SSOP | Microchip
DSPIC33CK64MP102-I/SS

DSPIC33CK64MP102-I/SS - 100MHz 64KB DSC 28-SSOP | Microchip

The Microchip Technology DSPIC33CK64MP102-I/SS is a 16-bit digital signal controller (DSC) with a single 100 MIPS dsPIC33C core, 64 KB (64K x 8) of Flash program memory and 8 KB of SRAM, housed in a 28-pin SSOP package (5.30 mm width). It integrates on-chip operational amplifiers, 12-bit high-speed ADCs, comparators and high-resolution PWM peripherals targeted at digital power and motor control. A digital signal controller combines the deterministic interrupt behavior and peripheral set of a microcontroller with the multiply-accumulate DSP engine of a digital signal processor. In the system hierarchy it sits above a plain MCU (adding a DSP engine and high-speed analog) and below a full DSP or application processor, making it the standard choice for closed-loop, sample-rate-driven control loops such as power-factor correction, resonant converters and field-oriented motor control. Key differentiating features of the dsPIC33CK64MP10X family include the 100 MHz single-core execution (up to 100 MIPS), a 3.0 V to 3.6 V single-supply operating range, integrated op amps that close current-sense loops without external amplifiers, and 12-bit ADCs with fast sample rates suitable for per-cycle current sampling in switching converters. High-resolution PWM modules provide sub-nanosecond edge placement for phase-shifted and LLC topologies. Architecturally, the device pairs the 16-bit fixed-point CPU with a DSP engine (barrel shifter, 17-bit x 17-bit multiplier, dual operand fetch) and DMA channels that move ADC results and UART/SPI data without CPU intervention. The -40C to +125C industrial temperature grade (suffix -I) suits harsh environments, and 3.3V-compatible I/O allows direct drive of gate drivers from the PWM pins. Typical applications include digital switch-mode power supplies (LLC, totem-pole PFC), brushless DC and PMSM motor drives using field-oriented control, digital lighting ballasts, battery chargers, and advanced sensing nodes. The op-amp-plus-ADC-plus-PWM integration lets one device implement an entire control loop with minimal external analog circuitry. Design consideration: budget the ADC sampling time and PWM dead time in firmware before layout, since the 100 MIPS core is fast enough that software latency, not silicon speed, usually limits loop bandwidth. Keep the analog ground for the ADC and op amps separated from the power-stage ground return path. This page synthesizes distributor pricing, drop-in same-family alternatives, pinout data and practical design notes not found on a single manufacturer page.

RFQ پەیوەندی
DSPIC33CK64MP103-E/M5 - 100MHz 16-bit DSC, 64KB Flash | Microchip
DSPIC33CK64MP103-E/M5

DSPIC33CK64MP103-E/M5 - 100MHz 16-bit DSC, 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP103-E/M5 is a 16-bit digital signal controller (DSC) from the dsPIC33CK64MP10X family, featuring a 100 MHz (100 MIPS) single-core dsPIC DSC engine, 64 KB of Flash program memory, 8 KB of RAM, integrated op amps, 12-bit ADCs, and high-resolution PWM peripherals, housed in a 36-pin UQFN (5x5 mm) package with extended -40C to +125C temperature operation. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes deterministic control loops (such as Field-Oriented Control for motors) while natively interfacing with sensors and power stages. The dsPIC33CK family extends this concept with a two-stage pipeline that executes one instruction per cycle at up to 100 MIPS. Key features include the 100 MHz dsPIC33CK core with DSP instruction extensions (MAC, DSP multiply-accumulate), on-chip operational amplifiers that reduce external analog component count, a high-speed 12-bit ADC supporting simultaneous multi-channel sampling for current sensing, and high-resolution PWM modules suitable for peak-current-mode and voltage-mode power conversion. The E-grade temperature rating (-40C to +125C) targets demanding industrial environments. Architecturally, the dsPIC33CK64MP103 pairs the single-core CPU with enhanced peripherals directly relevant to digital power: comparators, a 12-bit ADC with dedicated conversion triggers from the PWM module, and flexible clocking from an on-chip PLL. Deterministic interrupt latency supports tight control-loop deadlines in switching converters running at hundreds of kilohertz. Typical applications include motor control (PMSM/BLDC FOC), digital power supplies and LLC/PFC converters, UPS systems, advanced sensing, and automotive-adjacent industrial control nodes. The integrated op amps condition shunt-current signals directly, shortening the sensor-to-PWM feedback path. Design consideration: budget the 64 KB Flash and 8 KB RAM early; FOC with transformations and compensation networks typically consumes several kilobytes, and the /M5 UQFN-36 footprint cannot be expanded. Use the multiple PGECx/PGEDx ICSP pin pairs as matched pairs for programming and debugging. This page synthesizes distributor pricing context, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP105-I/PT - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP105-I/PT

DSPIC33CK64MP105-I/PT - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP105-I/PT is a 100 MHz single-core 16-bit digital signal controller (DSC) with 64 KB flash memory, 8 KB RAM, and a 48-pin TQFP (7x7 mm) package. It integrates a DSP engine, 12-bit high-speed ADCs, on-chip operational amplifiers, comparators, and high-resolution PWM peripherals targeted at real-time control. A digital signal controller combines the compute capability of a microcontroller with the mathematical throughput of a DSP. Within the power-management hierarchy, a DSC sits above a generic MCU: it executes a 16-bit modified Harvard architecture with an enhanced instruction set and dedicated DSP support, enabling closed-loop control loops (current, voltage, speed) at very high sampling rates in digital power and motor drive systems. Key features of the dsPIC33CK64MP10X family include a single dsPIC DSC core running at 100 MIPS, integrated DSP multiply-accumulate hardware, 12-bit ADCs with high sample rates, multiple internal op amps for current-sense conditioning, analog comparators, and advanced PWM modules with fine edge placement - all essential for fast, deterministic control of switching power stages and motor phases. Technically, the CPU uses a 16-bit modified Harvard architecture with an enhanced instruction set including significant DSP support, according to the Microchip dsPIC33CK64MP105 family data sheet (DS70005363E). The family is documented as enabling digital power, motor control, advanced sensing, and companion/co-processing designs. Typical applications include digital power supplies (LLC, totem-pole PFC), BLDC/PMSM motor drives, high-performance general-purpose embedded control, and advanced sensing front ends where the on-chip op amps and high-speed ADC replace external analog signal-conditioning components. Design consideration: all VDD/VSS pins must be connected and decoupled, and ICSP programming requires using PGECx/PGEDx pin pairs as matched pairs - connect ICSPCLK/ICSPDAT to the same numbered pair. This page synthesizes distributor pricing, drop-in alternatives within the same 48-pin TQFP footprint, pinout guidance, and practical design notes not found in a single datasheet page.

RFQ پەیوەندی
DSPIC33CK64MP202-E/2N - 100MHz 16-bit DSC, 64KB Flash | Microchip
DSPIC33CK64MP202-E/2N

DSPIC33CK64MP202-E/2N - 100MHz 16-bit DSC, 64KB Flash | Microchip

The Microchip DSPIC33CK64MP202-E/2N is a 16-bit digital signal controller (DSC) from the dsPIC33CK family, featuring a 100 MHz core, 64 KB of dual-panel flash memory, 8 KB of RAM, integrated op-amps, 12-bit ADCs, and high-resolution PWM outputs, housed in a 28-pin UQFN (6x6 mm) extended-temperature package rated from -40C to +125C. A digital signal controller combines the compute architecture of a microcontroller with the mathematical acceleration of a DSP, sitting in the hierarchy between general-purpose MCUs and full DSPs within the broader embedded processor category. The dsPIC33CK core executes one instruction per cycle with DSP multiply-accumulate and divide support, making it well suited to closed-loop control algorithms such as field-oriented motor control and average-current-mode power conversion. Key features of the DSPIC33CK64MP202 include the dual-panel flash architecture that allows live firmware updates while executing from the alternate panel, up to 3.5 Msps 12-bit ADC operation for fast current sampling, integrated operational amplifiers that offload external signal conditioning, and high-resolution PWM peripherals with dead-time control for bridge topologies. The -E extended temperature grade and Functional Safety (FuSa) support documented by distributors make the device suitable for demanding industrial environments. Technically, the 100 MHz dsPIC DSC core delivers 100 MIPS with a fixed-point DSP engine supporting two 40-bit accumulators, while the peripheral ecosystem includes UART, SPI, I2C, and configurable logic modules. The 8 KB of SRAM supports control-loop state variables and communications buffers, and the 64 KB flash provides ample space for control firmware and a bootloader. Typical applications include digital power supplies, brushless DC and PMSM motor drives, solar micro-inverters, LED drivers, and advanced sensing and control nodes. The integrated op-amps and fast ADCs reduce bill-of-material cost in current-sensing power stages, and the PWM resolution suits phase-shifted and synchronous converter topologies. For design, place the VCAP bulk capacitor close to the core-regulator pin and keep the analog supply filtered from the digital rail to preserve ADC accuracy at full sample rate. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP202-E/SS - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP202-E/SS

DSPIC33CK64MP202-E/SS - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP202-E/SS is a 16-bit digital signal controller (DSC) from the dsPIC33CK family, featuring a 100 MHz dsPIC DSC core, 64KB (64K x 8) dual-panel Flash with ECC, and 8KB of SRAM, housed in a 28-lead SSOP (SS) package with 0.65 mm terminal pitch and an extended -40C to +125C operating range. A digital signal controller combines the compute power of a DSP with the peripheral integration and control-oriented architecture of a microcontroller. Within the power management hierarchy, the dsPIC33CK sits in the digital signal controller -> 16-bit MCU -> embedded processor taxonomy, targeting real-time closed-loop control loops such as digital power supplies, motor control, and advanced sensing where deterministic interrupt latency and fast math matter. Key features include the 100 MHz (100 MIPS) single-core dsPIC33CK core with DSP engine, dual-partition (dual-panel) Flash enabling live firmware update, on-chip operational amplifiers, 12-bit ADCs, and high-resolution PWM peripherals - the exact peripheral set demanded by digital power and motor control designs. The E-suffix temperature grade guarantees operation to +125C for industrial environments. Architecturally, the device uses a modified Harvard architecture with a barrel shifter and hardware DSP multiply-accumulate support. Program Flash includes ECC and Memory Built-In Self-Test (MBIST) on SRAM, supporting functional-safety-oriented designs (DigiKey lists it under the dsPIC33CK FuSa category). Operating conditions are 3.0V to 3.6V single supply. Typical applications include digital power supplies (LLC, PFC, totem-pole stages), BLDC/PMSM motor control, LED lighting, and high-end sensing front ends where integrated op-amps buffer ADC inputs. Design consideration: the dsPIC33CK64MP202 has multiple PGECx/PGEDx ICSP pairs - debugger connections must use a matched pair, and all VDD/VSS pins must be connected for programming to succeed. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP202-I/SS - 100MHz 16-bit DSC, 64KB Flash | Microchip
DSPIC33CK64MP202-I/SS

DSPIC33CK64MP202-I/SS - 100MHz 16-bit DSC, 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP202-I/SS is a 16-bit digital signal controller (DSC) from the dsPIC33CK family, delivering up to 100 MIPS from a 100 MHz dsPIC33CK core with 64 KB (22 KWords) of ECC dual-partition program flash, 8 KB of SRAM, integrated op amps, a 12-bit ADC, and high-resolution PWM, packaged in a 28-lead SSOP (0.65 mm pitch). A digital signal controller combines the computational capability of a 16-bit MCU with DSP engine features such as single-cycle MAC, hardware divide, and barrel shifter. Within the power-management hierarchy, DSCs sit between general-purpose microcontrollers and dedicated DSPs, and are the standard choice for closed-loop control loops running at switching frequencies in the tens to hundreds of kilohertz. Key features include the 12-bit, 3.5 Msps ADC with up to 15 channels for simultaneous multi-phase current sampling, 4x2 high-speed PWM channels with 2 ns edge resolution supporting complementary or independent outputs with dead-time insertion, an integrated analog comparator, a 12-bit DAC for reference generation, and a CAN Flexible Data Rate (CAN FD) module for industrial and automotive networks. Dual-partition flash with ECC enables live firmware update without external memory. The modified Harvard architecture executes from a 3.0 V to 3.6 V supply and maintains DSP throughput of 100 MIPS across the industrial temperature range of -40C to +125C. The on-chip op amps buffer shunt-resistor signals directly, reducing BOM cost and board area in motor-drive power stages. Typical applications include digital power supplies (LLC, totem-pole PFC), brushless DC and PMSM field-oriented motor control, LED drivers, and advanced sensing and control in industrial automation, metering, and IoT nodes. Design consideration: all VSS and VDD pins must be connected during in-circuit programming, and PGECx/PGEDx must be used as matched pairs - mixing pairs from different channels prevents ICSP programming. This page synthesizes distributor inventory links, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet, with pricing references as of 2026-09-23.

RFQ پەیوەندی
DSPIC33CK64MP203T-I/M5 - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP203T-I/M5

DSPIC33CK64MP203T-I/M5 - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP203T-I/M5 is a 16-bit dsPIC33CK digital signal controller (DSC) with a 100 MHz core (up to 100 MIPS), 64 KB (64K x 8) of Flash program memory, 8 KB of RAM, and a 36-pin UQFN (5x5 mm) package with exposed pad. It operates from a 3.0 V to 3.6 V supply over an industrial -40C to +85C temperature range. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and deterministic interrupt architecture of a microcontroller. Within the embedded-systems hierarchy, the dsPIC33CK family sits between general-purpose MCUs and application-specific DSPs, making it a common choice where tight real-time control loops meet moderate signal-processing workloads such as digital power conversion and motor control. Key features include the 16-bit dsPIC33CK core with DSP instruction set, 250 ps PWM resolution for high-resolution power-stage control, CAN FD for robust automotive and industrial networking, and integrated analog peripherals including 3 operational amplifiers and 3 comparators that reduce external component count. The M5 suffix part also carries Functional Safety (FuSa) qualification documentation support per Microchip's product page. Technically, the core executes from a 24-bit instruction width with hardware loop and barrel shifter support, and DMA offloads data movement between high-speed peripherals such as the ADC and PWM, allowing interrupt-free closed-loop control in digital power designs. Typical applications include digital switch-mode power supplies, PFC stages, brushless DC and PMSM motor drives, and industrial sensing nodes where CAN FD connectivity is required. Design consideration: the 3.0-3.6 V supply window means designers must plan an LDO or buck regulator upstream; the exposed pad must be soldered to a ground plane for thermal and signal integrity. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes beyond the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP205-E/M4 - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP205-E/M4

DSPIC33CK64MP205-E/M4 - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP205-E/M4 is a 100 MHz single-core 16-bit digital signal controller (DSC) with 64 KB of program Flash, 8 KB of RAM, three integrated operational amplifiers, three comparators, and a Pattern Generator (PTG), housed in a 48-pin UQFN (6x6 mm) package with exposed pad. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and deterministic control of a microcontroller. Within the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it executes single-cycle MAC and DSP instructions while integrating high-resolution PWM, ADC, and analog front ends on one die. Microchip's dsPIC33CK family targets real-time closed-loop control systems where sampling, computation, and PWM updates must complete within one switching cycle. Key differentiating features include the 100 MIPS dsPIC33C core with DSP instruction extensions and zero-overhead loops, dual-partition Flash with live update support and ECC, three on-chip op amps that eliminate external amplifiers in current-sense chains, and a high-resolution PWM module suited to peak-current-mode and multiphase power conversion. The -E temperature suffix guarantees operation from -40C to +125C, supporting automotive-adjacent and high-temperature industrial environments. The 48-UQFN (6x6) package with exposed pad provides low-inductance ground returns for fast analog peripherals and a compact 36 mm2 footprint for dense power boards. Typical applications include digital power supplies (totem-pole PFC, LLC), brushless DC and PMSM motor control (FOC), digital LED lighting, and advanced sensing where the PTG and CLC peripherals offload sequencing tasks from the CPU. Design consideration: the 3.0V to 3.6V operating range and dense UQFN pin pitch demand careful PCB stack-up; place the exposed thermal pad on a solid ground plane with multiple thermal vias. This page synthesizes distributor pricing, same-footprint family alternatives, and practical design guidance not found in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP205T-I/M4 - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP205T-I/M4

DSPIC33CK64MP205T-I/M4 - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP205T-I/M4 is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB Flash program memory, and 8 KB RAM, housed in a 48-pin UQFN (6x6 mm, /M4) surface-mount package with exposed pad. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and deterministic interrupt architecture of a microcontroller. Within the power management hierarchy, the dsPIC33CK family sits in the embedded processor category: microcontroller -> digital signal controller -> digital signal processor. These single-core DSCs are purpose-built for closed-loop control applications where fast, deterministic math (MAC, division, trigonometric) executes inside ISR deadlines measured in microseconds. Key features include DC to 100 MIPS instruction throughput at 3.0-3.6V operation, a high-resolution PWM module with 250 ps effective resolution for digital power converters, three on-chip operational amplifiers and three analog comparators, and a CAN FD interface for automotive and industrial networks. Connectivity peripherals cover I2C, SPI, UART/USART, IrDA, and LINbus. The device belongs to the Functional Safety (FuSa) supported dsPIC33CK family and operates from -40C to +85C (industrial, /I temperature suffix). Architecturally, the 16-bit dsPIC core uses an enhanced Harvard bus structure with a 24-bit instruction word, hardware DSP engine (single-cycle MAC), zero-overhead loops, and hardware division support, enabling control-law updates at PWM frequencies well above 500 kHz in digital power designs. Typical applications include digital power supplies (LLC, PFC, buck), brushless and PMSM motor control, solar micro-inverters, and CAN FD-connected sensing nodes. The integrated op-amps and comparators eliminate external analog signal-conditioning ICs in current-sense paths. Design consideration: the 48-pin UQFN 6x6 package requires thermal via arrays under the exposed pad for high-power switch-mode designs; plan ADC sampling synchronized to the PWM trigger outputs. This page synthesizes verified distributor data, drop-in alternatives, and application-specific design guidance not found in the manufacturer datasheet alone.

RFQ پەیوەندی
DSPIC33CK64MP206-E/MR - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP206-E/MR

DSPIC33CK64MP206-E/MR - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP206-E/MR is a 100 MHz single-core 16-bit digital signal controller (DSC) with 64 KB of program Flash, 8 KB of data SRAM, 3 on-chip operational amplifiers, 3 analog comparators, and a Peripheral Trigger Generator (PTG), housed in a 64-pin QFN (9x9 mm) package rated for -40C to +150C operation. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and deterministic control behavior of a microcontroller. Within the power-management hierarchy, the dsPIC33CK family sits between general-purpose MCUs and dedicated digital power ASICs, providing a modified Harvard architecture with a 16-bit dsPIC DSC core executing up to 100 MIPS for closed-loop control of power conversion and motor drive systems. Key features include dual-partition Flash with error-correction code (ECC) and Live Update support, which allows firmware upgrades while the controller continues to run; Memory Built-In Self-Test (MBIST) for functional-safety designs; high-resolution PWM outputs suited to digitally controlled power supplies; and CAN Flexible Data (CAN FD) for industrial and automotive networking. The three integrated op-amps reduce external component count in current-sense front ends. Technically, the dsPIC33CK core operates from 3.0V to 3.6V and integrates DSP multiply-accumulate instructions alongside deterministic interrupt latency, making it well matched to fixed-point control loops executing at switching frequencies of hundreds of kilohertz. The functional-safety (FuSa) variant designation supported by this part aids IEC 61508 and ISO 26262 oriented development flows. Typical applications include digital power supplies (LLC, totem-pole PFC), brushless DC and PMSM motor control, solar micro-inverters, and battery-management systems. The integrated analog front end (op-amps, comparators, 12-bit ADC peripherals in the family) enables single-chip current shaping and fast overcurrent protection. When designing with this device, budget the 8 KB SRAM carefully for control-loop state plus communications buffers, and leverage the PTG to offload deterministic trigger sequencing from the CPU. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with specifications verified against Microchip and distributor listings as of 2026-09-23.

RFQ پەیوەندی
DSPIC33CK64MP206-I/PT - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP206-I/PT

DSPIC33CK64MP206-I/PT - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP206-I/PT is a 16-bit digital signal controller (DSC) featuring a 100 MHz (100 MIPS) dsPIC33CK core, 64KB of program Flash with ECC and dual-partition live update, and 8KB of data SRAM, housed in a 64-pin TQFP (10x10 mm) package with 3 on-chip operational amplifiers, 3 high-speed analog comparators, a Programmable Gain Amplifier (PGA) and high-resolution PWM peripherals. What is a Digital Signal Controller? A DSC is a hybrid processor that combines the deterministic interrupt-driven architecture of a microcontroller with the hardware multiply-accumulate (MAC) and DSP instruction set of a digital signal processor. Within the embedded-systems taxonomy, the DSC sits between general-purpose MCUs and dedicated digital-power ASICs: it executes closed-loop control firmware at switching frequencies from tens of kHz to well above 1 MHz while simultaneously managing communications, sequencing and fault handling in one chip. Key differentiating features include the modified-Harvard dsPIC33CK core with single-cycle MAC, dual-partition Flash supporting live field-update with no downtime, CAN FD for in-vehicle and industrial networking, high-resolution PWM with sub-nanosecond effective edge placement for digital power topologies, and an integrated 12-bit ADC front end that closes current/voltage loops without external signal-conditioning ICs. Architecturally, the deterministic interrupt latency and DSP MAC unit enable fixed-point current-mode and voltage-mode control loops running well above audible and typical control bandwidths. The on-chip op-amps feed the comparators and ADC, allowing direct current-sense and voltage-sense conditioning for buck, boost, totem-pole PFC, LLC and phase-shifted full-bridge converters. Typical applications include digital switched-mode power supplies, LLC and PFC stages, sensorless field-oriented control of PMSM and BLDC motors, solar micro-inverters and DC-DC converters, and industrial sensing nodes that benefit from the on-chip CAN FD and high-resolution PWM. When designing with this part, budget the analog front-end (op-amp bandwidth, comparator propagation delay) against your target switching frequency and use the dual-partition Flash live-update feature carefully so bootloader and application firmware never execute from the partition currently being programmed. This page synthesizes distributor availability data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP206T-I/MR - 100MHz DSC 64KB Flash QFN-64 | Microchip
DSPIC33CK64MP206T-I/MR

DSPIC33CK64MP206T-I/MR - 100MHz DSC 64KB Flash QFN-64 | Microchip

The Microchip Technology DSPIC33CK64MP206T-I/MR is a 16-bit digital signal controller (DSC) from the dsPIC33CK family, featuring a 100 MHz dsPIC DSC core, 64KB (64K x 8) of Flash program memory, 8KB of RAM, and 53 general-purpose I/O pins in a 64-pin QFN (9x9 mm, MR) package with exposed pad. It operates from a 3V to 3.6V supply across an industrial -40C to +85C temperature range. A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and control architecture of a microcontroller (MCU). In the system hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP, making it the preferred processor class for real-time closed-loop control such as digital power conversion, motor control, and advanced sensing. Key differentiating features include the 100 MHz core with DSP engine and barrel shifter, on-chip 3 op-amps and 3 comparators that reduce external analog component count, high-resolution PWM (HRPWM) for fine duty-cycle and phase control, and CAN Flexible Data (CAN FD) support for automotive and industrial networking. The device also integrates multiple serial interfaces (4 serial I/O ports), DMA channels, and a PTG (peripheral trigger generator) for autonomous peripheral sequencing. Architecturally, the dsPIC33CK core executes from Flash with a 24-bit instruction width and uses pipelined, single-cycle MAC and multiply instructions, enabling control-loop rates well above 100 kHz in digital power and FOC motor-control applications. The integrated analog front-end (op-amps, comparators, 12-bit ADC pipelines in the MP family) allows direct connection of current shunts and voltage dividers, minimizing signal-chain latency. Typical applications include digital power supplies and 48V-to-12V DC/DC brick converters (as in the EPC9143 reference design using a sibling dsPIC33CK32MP102), PFC stages, BLDC/PMSM/ACIM motor drives, battery chargers, and industrial automation nodes requiring CAN FD connectivity. Design consideration: the device requires a stable 3.3V rail (3.0V-3.6V), decoupled close to the QFN exposed pad; the exposed thermal pad must be soldered to a ground pour for both electrical return and heat dissipation. Use Microchip's MPLAB X IDE and X16 compiler with the dsPIC33CK device family support pack. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing verified as of 2026-09-23.

RFQ پەیوەندی
DSPIC33CK64MP206T-I/PT - 100MHz 16-bit DSC 64KB Flash TQFP-64 | Microchip
DSPIC33CK64MP206T-I/PT

DSPIC33CK64MP206T-I/PT - 100MHz 16-bit DSC 64KB Flash TQFP-64 | Microchip

The Microchip Technology DSPIC33CK64MP206T-I/PT is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB of program Flash and 8 KB of RAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates analog and control peripherals aimed at time-critical embedded control. A digital signal controller combines the deterministic control flow of a microcontroller with the multiply-accumulate (DSP) throughput of a digital signal processor in a single core. Within the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the standard choice for closed-loop control loops such as digital power conversion, motor control and advanced sensing, where fast interrupt latency and hardware PWM resolution matter more than raw general-purpose compute. Key differentiating features of the MP206 variant include three integrated operational amplifiers (op-amps) and three analog comparators, which offload analog signal conditioning from external components, plus the Peripheral Trigger Generator (PTG) for hardware-sequenced peripheral coordination. The family provides High-Resolution PWM and CAN Flexible Data (CAN FD) connectivity, essential for automotive and industrial networks. Technically, the dsPIC33CK family uses a modified Harvard architecture 16-bit core with DSP instructions, single-cycle MAC, and hardware loop support, executing at up to 100 MIPS from 3.0V to 3.6V. Program Flash features ECC and dual-partition live update capability, enabling field firmware updates without external memory - a significant reliability advantage in digital power products. Four DMA channels service high-rate ADC and communication data streams without CPU intervention. Typical applications include digitally controlled AC-DC and DC-DC power supplies (totem-pole PFC, LLC), PMSM/BLDC and ACIM motor drives, and high-performance sensing front ends where the on-chip op-amps amplify shunt or sensor signals directly into the ADC. CAN FD support also suits automotive auxiliary control nodes. When designing, budget the peripheral pin mapping early: with 64 pins and a rich peripheral set, use Microchip MPLAB Code Configurator to resolve pin-mux conflicts before layout. Plan VCAP and decoupling per the datasheet power section for core stability at 100 MHz. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet, verified against Mouser, DigiKey and Microchip product pages as of 2026-09-23.

RFQ پەیوەندی
DSPIC33CK64MP208-I/PT - 100MHz DSC, 64KB Flash, TQFP-80 | Microchip
DSPIC33CK64MP208-I/PT

DSPIC33CK64MP208-I/PT - 100MHz DSC, 64KB Flash, TQFP-80 | Microchip

The Microchip Technology DSPIC33CK64MP208-I/PT is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB (64K) of program Flash and 8 KB of data SRAM, housed in an 80-pin TQFP (PT) package. It operates from a 3.0V to 3.6V supply across the industrial -40C to +85C temperature range and delivers up to 100 MIPS of DSP performance. A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the deterministic, interrupt-driven control behavior of a microcontroller (MCU). Within the power-management hierarchy, DSCs sit at the center of digitally controlled power conversion systems, coordinating sensing, control-loop execution, and PWM generation in a single silicon device, which is why they dominate modern digital power and motor-control architectures. Key differentiating features include a high-resolution PWM with 250 ps effective resolution for fine duty-cycle control, CAN Flexible Data (CAN FD) for automotive and industrial networking, three on-chip operational amplifiers and three comparators that reduce external analog component count, and a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. The dsPIC33CK family also offers ECC-protected program Flash with Live Update dual-partition bootloading on higher-density members. Architecturally, the device uses a modified Harvard architecture with a single 100 MHz dsPIC DSC core, DSP instructions, a barrel shifter, boundary-scan (JTAG) support, four DMA channels, four external interrupts, four serial I/O ports, and multiple timers, enabling tight, deterministic control loops with minimal CPU overhead. Typical applications include digital power supplies (totem-pole PFC, LLC converters), brushless DC and PMSM motor control (FOC sensorless algorithms), advanced sensing and control nodes, and CAN FD-connected industrial or automotive subsystems, where 250 ps PWM resolution and integrated analog directly improve efficiency and BOM cost. Design consideration: the 3.0V to 3.6V supply window requires a clean 3.3V rail; budget decoupling at every VDD pin pair of the TQFP-80 and follow Microchip's layout guidance for the high-resolution PWM outputs to minimize switching-node noise coupling into the on-chip op-amps. This page synthesizes distributor listings, family cross-reference data, and drop-in alternative analysis not found in the manufacturer datasheet alone.

RFQ پەیوەندی
DSPIC33CK64MP502-E/2N - 100MHz 16-bit DSC CAN-FD | Microchip
DSPIC33CK64MP502-E/2N

DSPIC33CK64MP502-E/2N - 100MHz 16-bit DSC CAN-FD | Microchip

The Microchip DSPIC33CK64MP502-E/2N is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB (64K x 8) dual-partition Flash with ECC, 8 KB SRAM, CAN FD, integrated op-amps, 12-bit ADCs and high-resolution PWM, housed in a 28-pin UQFN (6x6) package rated from -40C to +150C. A digital signal controller combines the compute power of a digital signal processor (DSP) with the peripheral integration and control-oriented architecture of a microcontroller (MCU). The dsPIC33CK family sits in the broader hierarchy of digital signal processors within embedded processing ICs, using a modified Harvard architecture with a single-core DSP engine that executes up to 100 MIPS from a 3.0V to 3.6V supply. Key features include the 100 MHz dsPIC DSC core with DSP instruction extensions, dual-panel program Flash supporting live update firmware switching, CAN Flexible Data (CAN FD) networking for automotive and industrial buses, on-chip operational amplifiers that reduce external analog BOM, and 12-bit ADCs feeding high-resolution PWM modules for digital power conversion. The -E/2N suffix denotes the extended temperature range (-40C to +150C) in the 28-pin UQFN package, and the device is positioned as a Functional Safety (FuSa) capable part. Architecturally, the modified Harvard core separates program and data buses for simultaneous instruction fetch and data access, while hardware DSP multiply-accumulate operations accelerate control-loop mathematics. The dual-partition Flash with ECC and live update enables safe field firmware updates in digital power products that cannot tolerate downtime. Typical applications include digital power supplies (totem-pole PFC, LLC converters), brushless DC and PMSM motor control, advanced sensing and control nodes, and CAN FD-connected automotive or industrial subsystems where the 150C rating and integrated analog reduce system cost. Design consideration: the 3.0V to 3.6V supply window means the 3.3V rail must be well regulated; decouple each VDD pin with 0.1uF ceramics close to the package and follow Microchip layout guidance for the high-resolution PWM outputs to minimize switching-node coupling into the ADC. This page synthesizes distributor listings, drop-in family alternatives, and application-specific design context not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP502-E/SS - 100MHz 16-bit DSC CAN-FD | Microchip
DSPIC33CK64MP502-E/SS

DSPIC33CK64MP502-E/SS - 100MHz 16-bit DSC CAN-FD | Microchip

The Microchip Technology DSPIC33CK64MP502-E/SS is a 100 MHz single-core 16-bit digital signal controller (DSC) with 64 KB of dual-partition program flash with ECC, 8 KB of data SRAM, CAN FD, integrated op-amps, and 12-bit ADCs, housed in a 28-pin SSOP (SS) package with extended temperature operation. A digital signal controller combines the compute throughput of a digital signal processor with the deterministic control and peripheral integration of a microcontroller. Within the power-management hierarchy, the dsPIC33CK family sits in the broader 16-bit DSC / MCU / embedded processor taxonomy and is optimized for closed-loop control loops running at switching frequencies of hundreds of kilohertz, where a generic MCU would struggle to execute the control law plus PWM updates in time. Key features include the dsPIC33CK DSC core running at up to 100 MIPS, up to 256 KB flash with ECC and Live Update (dual-partition flash) across the family (64 KB on this part), High-Resolution PWM (HRPWM) with sub-nanosecond edge placement, and CAN Flexible Data (CAN FD) for automotive and industrial networking. The modified Harvard architecture with dedicated DSP multiply-accumulate hardware enables single-cycle MAC operations for filtering and transform-heavy algorithms. Technical depth comes from the integrated analog subsystem: on-chip operational amplifiers buffer current-shunt signals directly, and fast 12-bit ADCs support simultaneous sampling of multiple channels, minimizing phase error in current-mode control. The -40C to +125C (E-grade, extended) operating range supports industrial and automotive-adjacent environments. Typical applications include digital power supplies and PFC stages, BLDC/PMSM motor control with sensorless field-oriented control, and CAN FD-connected industrial control nodes. The high-resolution PWM makes it a natural fit for LLC and totem-pole topologies requiring precise phase-shift control. Design consideration: the core operates from 3.0V to 3.6V, so a 3.3V rail is required; budget flash partitions carefully if using Live Update bootloaders. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP502T-I/2N - 100MHz 64KB CAN-FD DSC | Microchip
DSPIC33CK64MP502T-I/2N

DSPIC33CK64MP502T-I/2N - 100MHz 64KB CAN-FD DSC | Microchip

The Microchip Technology DSPIC33CK64MP502T-I/2N is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64KB of dual-partition program Flash with ECC, 8KB of data SRAM, and CAN FD connectivity, housed in a 28-pin UQFN (6x6 mm) package with exposed pad. A digital signal controller combines the computational power of a digital signal processor with the deterministic control and peripheral set of a microcontroller. Within the power-management IC and embedded control hierarchy, the DSC sits above general-purpose MCUs for applications that need fast math and tight control loops, such as field-oriented motor control and digitally controlled switched-mode power supplies. Key features include 100 MIPS instruction throughput (up to 100 MIPS per Microchip), three integrated operational amplifiers, three analog comparators, 12-bit high-speed ADCs, high-resolution PWM peripherals for power conversion, and a Controller Area Network Flexible Data-rate (CAN FD) interface. The dual-panel Flash supports live update firmware upgrades, and the device is positioned for functional safety (FuSa) development per distributor listings. The dsPIC33CK architecture uses a modified Harvard design with a single 100 MHz core operating from a 3.0V to 3.6V supply, supporting operation from DC to 100 MIPS over the industrial -40C to +85C temperature range indicated by the I-grade suffix. Integrated analog (op-amps and comparators) reduces external component count in current-sense and protection circuits. Typical applications include digital power supplies (totem-pole PFC, LLC converters), brushless DC and PMSM motor control, automotive and industrial CAN FD nodes, and high-end sensing and control systems. Design consideration: the 28-pin UQFN (6x6) exposes the peripheral set on a limited pin count, so plan pin muxing early; the exposed pad must be soldered to a grounded copper pour for thermal and signal-integrity performance. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes beyond the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP502T-I/SS - 100MHz 64KB Flash DSC | Microchip
DSPIC33CK64MP502T-I/SS

DSPIC33CK64MP502T-I/SS - 100MHz 64KB Flash DSC | Microchip

The Microchip Technology DSPIC33CK64MP502T-I/SS is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB of dual-panel flash memory, and 8 KB of RAM, housed in a 28-pin SSOP package. It integrates CAN-FD, high-speed 12-bit ADCs, analog comparators, op amps, and advanced PWM peripherals for digital power and motor control. A digital signal controller combines the computational capability of a DSP with the peripheral set and ease of use of a microcontroller, sitting within the broader hierarchy of embedded processors: DSC -> microcontroller -> embedded MCU/SoC. The dsPIC33CK family executes a single-cycle MAC DSP engine alongside the 16-bit CPU, making it a common choice in the power-management and industrial-control semiconductor space. Key features include the 100 MHz modified Harvard architecture core with DSP instruction extensions, dual-panel flash enabling live firmware updates, a 3.5 Msps 12-bit ADC pair, CAN-FD for automotive and industrial networks, and integrated op amps that reduce external component count in current-sense loops. The MP variant adds two on-chip operational amplifiers and high-resolution PWM suitable for closed-loop power conversion. The dual-panel flash architecture allows firmware execution from one panel while erasing/programming the other, a significant advantage for field-updatable digital power products. Typical applications include switch-mode power supplies, PFC stages, BLDC/PMSM motor drives, solar micro-inverters, and CAN-FD-connected industrial sensing nodes where deterministic interrupt latency and fast ADC sampling are critical. Design consideration: the device operates from 3.0 V to 3.6 V, so a 3.3 V LDO or buck regulator is required; budget the 8 KB RAM carefully when using complex control loops with float math. This page synthesizes distributor pricing, drop-in alternatives, design notes, and application guidance not found in a single manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP503-E/M5 - 100MHz 64KB DSC | Microchip
DSPIC33CK64MP503-E/M5

DSPIC33CK64MP503-E/M5 - 100MHz 64KB DSC | Microchip

The Microchip Technology DSPIC33CK64MP503-E/M5 is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB of Flash program memory, and 8 KB of RAM, housed in a 36-pin UQFN (5x5 mm) exposed-pad package with an extended temperature rating. A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the integrated peripherals and deterministic control flow of a microcontroller (MCU). In the power-management hierarchy, DSCs sit between general-purpose MCUs and dedicated DSPs, making them the preferred choice for closed-loop control systems that need fast math (MAC, barrel shifter, DSP engine) alongside precise analog and timing peripherals on a single silicon die. Key features of this device include a 100 MHz dsPIC33CK CPU core with DSP instruction extensions, 64 KB (64K x 8) of ECC Flash memory, on-chip 3 operational amplifiers and 3 analog comparators for embedded sensing loops, a PTG (Peripheral Trigger Generator) for hardware-sequenced operation, and CAN-FD connectivity for automotive and industrial networks. The MP family suffix denotes the full analog-peripheral set including the three op-amps, which offload external signal conditioning in current-sense applications. Architecturally, the dsPIC33CK core delivers single-cycle MAC and dual-issue instruction execution, allowing deterministic control-loop latencies critical for peak-current-mode and sensorless field-oriented control. The Peripheral Trigger Generator enables ADC sampling and PWM events to be chained in hardware, reducing CPU interrupt load. The device is qualified to AEC-Q100 for automotive use, and the -E suffix indicates the extended operating temperature range for harsh environments. Typical applications include digital power supplies (LLC, totem-pole PFC), brushless DC and PMSM motor control, advanced sensing front-ends that exploit the three integrated op-amps, and CAN-FD-connected industrial control nodes. Design consideration: the 36-UQFN exposed pad must be soldered to a ground pour for thermal dissipation and signal integrity; plan ADC/PWM pin mapping early because peripheral pin-select flexibility trades against layout complexity. This page synthesizes verified distributor data, drop-in alternatives within the dsPIC33CK/CH families, pricing tiers, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP505-E/PT - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP505-E/PT

DSPIC33CK64MP505-E/PT - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip DSPIC33CK64MP505-E/PT is a 100 MHz single-core 16-bit dsPIC33CK digital signal controller (DSC) with 64 KB of program Flash (with ECC and dual-partition live update), 8 KB of data SRAM, and integrated CAN FD, housed in a 48-pin TQFP (7x7 mm) package rated from -40C to +150C operating conditions at 3.0V to 3.6V. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and deterministic control of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes single-cycle MAC and DSP instructions while also hosting motor-control PWM, analog comparators, op-amps, and communication interfaces on one die. The dsPIC33CK family from Microchip Technology targets real-time closed-loop control systems. Key features of this part include a 100 MIPS dsPIC33CK core with modified Harvard architecture, up to 24 KB-class data SRAM with Memory Built-In Self-Test (MBIST) in the family, three integrated operational amplifiers, three analog comparators, and a Peripheral Trigger Generator (PTG). High-Resolution PWM and CAN Flexible Data (CAN FD) make it well suited to digitally controlled power stages and fieldbus-connected nodes. Technical depth: the dsPIC33CK core executes DC to 100 MIPS with DSP multiply-accumulate instructions, while dual-partition Flash with ECC enables live firmware update in safety-oriented designs. Functional Safety (FuSa) support is documented by Microchip, and the -E extended-temperature grade plus AEC-Q100 qualification support automotive deployments. Typical applications include digital power supplies (PFC, LLC, totem-pole), PMSM/BLDC and SRM motor control, automotive control nodes using CAN FD, and advanced sensing with on-chip analog front ends. Design consideration: budget the 3.0V to 3.6V supply rail early; at 100 MIPS the core requires clean decoupling and attention to the high-resolution PWM clock source for best control-loop resolution. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP505-I/M4 - 100MHz 16-bit DSC 64KB Flash | Microchip
DSPIC33CK64MP505-I/M4

DSPIC33CK64MP505-I/M4 - 100MHz 16-bit DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP505-I/M4 is a 16-bit digital signal controller (DSC) featuring a 100 MHz dsPIC33CK core, 64 KB of Flash program memory, and 8 KB of RAM, housed in a 48-pin UQFN (6x6 mm) package with industrial temperature rating (-40C to +85C). A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and control architecture of a microcontroller (MCU). Within the power management hierarchy of embedded systems, the dsPIC33CK family sits in the 16-bit DSC class and is purpose-built for closed-loop control loops such as digital power conversion, motor control, and advanced sensing, where deterministic interrupt latency and high-resolution pulse-width modulation (PWM) matter more than general-purpose application throughput. Key features of the DSPIC33CK64MP505 include three on-chip operational amplifiers (op-amps), three analog comparators, a high-resolution PWM peripheral, CAN Flexible Data-rate (CAN FD) for robust networking, and the Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. These peripherals offload time-critical tasks from the CPU, enabling faster control-loop update rates. Technically, the dsPIC33CK core supports DSP instructions including barrel shifting and single-cycle MAC operations, with DMA channels servicing high-bandwidth peripherals such as the ADC. This allows sampling and control computations to run at hundreds of kilohertz loop rates typical of digital power supplies and field-oriented control (FOC) motor drives. Typical applications include digital switch-mode power supplies (AC-DC, DC-DC), brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) control, LED drivers, and CAN FD-connected industrial sensing nodes. For design, plan decoupling on all VDD pairs and validate the high-resolution PWM dead-time settings early; the extended-temperature -E variant shares the footprint if wider ambient ranges are needed later. This page synthesizes distributor pricing, same-family drop-in variants, and practical design notes not consolidated in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP505T-I/PT - 100MHz 64KB DSC 48-TQFP | Microchip
DSPIC33CK64MP505T-I/PT

DSPIC33CK64MP505T-I/PT - 100MHz 64KB DSC 48-TQFP | Microchip

The Microchip Technology DSPIC33CK64MP505T-I/PT is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB of program flash and 8 KB of RAM, housed in a 48-pin TQFP (7x7 mm) package. A digital signal controller combines the compute power of a DSP with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, the DSC sits above generic MCUs and below application-specific DSPs, making it the standard choice when fast control loops (switching regulators, motor drives) must execute deterministic algorithms such as PI/PID control at hundreds of kilohertz. The dsPIC33CK family belongs to the broader 16-bit dsPIC product line from Microchip. Key features of the MP505 variant include three integrated operational amplifiers (op-amps) for direct current-sense conditioning, three high-speed analog comparators, a 12-bit ADC with high sampling capability, and a Peripheral Trigger Generator (PTG) for autonomous sequenced operation. The controller implements CAN Flexible Data-rate (CAN-FD) for modern in-vehicle and industrial networking, plus multiple 16-bit high-resolution PWM modules purpose-built for digital power conversion. Architecturally, the dsPIC33CK core uses a modified Harvard architecture with DSP engine support, single-cycle MAC, dual operands, and barrel shifting. The family datasheet notes support for up to 100 MIPS operation from a 3.0V to 3.6V supply, dual-partition flash with ECC and live update capability, and Memory Built-In Self-Test (MBIST) on data SRAM, features that support functional-safety oriented designs (DigiKey lists this family as Functional Safety (FuSa) capable). Typical applications include digital power supplies ( LLC, totem-pole PFC ), BLDC/PMSM/ACIM motor control, automotive and industrial CAN-FD nodes, and advanced sensing systems where the on-chip op-amps eliminate external analog front-end components. Design consideration: the core requires a 3.0V to 3.6V rail, so plan a 3.3V LDO or buck with low ripple; the 7x7 mm TQFP exposes an industry-standard footprint requiring no special thermal design at typical operating currents. This page synthesizes distributor pricing data, drop-in alternatives, design guidance, and FAQ content not found together in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP506-E/PT - 100MHz 16-bit DSC 64KB Flash CAN-FD | Microchip
DSPIC33CK64MP506-E/PT

DSPIC33CK64MP506-E/PT - 100MHz 16-bit DSC 64KB Flash CAN-FD | Microchip

The Microchip Technology DSPIC33CK64MP506-E/PT is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 64 KB (64K x 8) Flash memory, 8 KB RAM, and a 64-pin TQFP (10x10 mm) package with extended temperature operation from -40C to +125C. A digital signal controller combines the computational throughput of a digital signal processor with the deterministic control and peripheral set of a microcontroller. Within the power management hierarchy, a DSC sits above a general-purpose MCU and is designed specifically for closed-loop control loops such as digital power conversion, motor commutation, and high-speed sensing, where fast interrupt latency and cycle-accurate PWM matter. Key features include the 100 MHz dsPIC33CK core with DSP instruction support, on-chip 3 op-amps and 3 comparators that eliminate external analog front-end components, a high-resolution PWM module for fine duty-cycle and phase control, and CAN Flexible Data (CAN FD) connectivity for automotive and industrial networks. The device is designated Functional Safety (FuSa) capable, supporting development under safety-oriented design flows. The architecture integrates enhanced peripherals around the core: a 12-bit high-speed ADC pipeline feeding control loops, Peripheral Trigger Generator (PTG) for autonomous sequencing, and DMA for data movement without CPU intervention. The integrated op-amps can be configured as signal-chain amplifiers for current-sense feedback, reducing bill-of-material cost in power converters. Typical applications include digital power supplies (LLC, totem-pole PFC), brushless DC and PMSM motor control, solar inverters, and CAN FD-enabled automotive or industrial control nodes. Design-wise, the 64-pin TQFP requires a solid VDD/VSS decoupling network and attention to the internal regulator VCAP capacitor for stable core supply. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی
DSPIC33CK64MP508-E/PT - 100 MHz 16-bit DSC, 64KB Flash | Microchip
DSPIC33CK64MP508-E/PT

DSPIC33CK64MP508-E/PT - 100 MHz 16-bit DSC, 64KB Flash | Microchip

The Microchip Technology DSPIC33CK64MP508-E/PT is a 100 MIPS single-core 16-bit digital signal controller (DSC) with 64 KB of program Flash with ECC and dual-partition Live Update, 8 KB of data SRAM with MBIST, integrated CAN FD, three 12-bit SAR ADCs, and high-resolution PWM, housed in an 80-pin TQFP (PT, 12x12 mm) package rated from -40C to +150C. A digital signal controller combines the compute power of a DSP with the peripheral integration and deterministic interrupt structure of a microcontroller. Within the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated digital signal processor: it executes tight control loops (current, voltage, phase) in digital power converters and motor drives while managing communication stacks such as CAN FD. The dsPIC33CK family implements a Modified Harvard architecture with a DSP-enhanced instruction set including DSP engine, MAC and dual-operand fetch. Key differentiating features include up to 100 MIPS performance (DC to 100 MIPS per the Microchip datasheet DS70005349), dual-partition Flash with ECC and Live Update enabling in-field firmware upgrades without downtime, nine MCCP/SCCP timer modules for capture/compare/PWM, and three on-chip op amps plus comparators that offload analog signal conditioning from external components. The Peripheral Trigger Generator (PTG) provides up to 15 trigger sources and a CPU-independent state machine sequencer. Architecturally, the dsPIC33CK core couples a 16-bit CPU with DSP engine, hardware loops and fast interrupts, while the high-resolution PWM (HRPWM) achieves sub-nanosecond-equivalent duty-cycle resolution for switching power stages, and the CAN FD module supports flexible-data-rate automotive and industrial networking. Typical applications include digital power supplies (totem-pole PFC, LLC), PMSM/BLDC motor control, automotive sensing and control nodes using CAN FD, and industrial control systems requiring deterministic real-time response. Design consideration: the extended-temperature E-grade device operates from 3.0V to 3.6V only; ensure the 3.3V rail remains within tolerance at full 100 MHz clock speed, and verify Flash endurance and retention figures in the datasheet for your ambient temperature. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ پەیوەندی