المنتجات (44,000+)

MPC8321CVRADDC - 266MHz PowerQUICC II Pro MPU, 516-PBGA | NXP
MPC8321CVRADDC

MPC8321CVRADDC - 266MHz PowerQUICC II Pro MPU, 516-PBGA | NXP

The NXP MPC8321CVRADDC is a PowerPC e300c2 microprocessor IC from the MPC83xx PowerQUICC II Pro family, running at 266 MHz core clock speed on a 32-bit architecture housed in a 516-ball TEBGA package (27 mm x 27 mm). The part is fabricated on a 90 nm process and operates from 1.8 V/2.5 V/3.3 V supply rails, integrating a PowerQUICC II Pro communications engine with DDR1/DDR2 memory controller, PCI, USB 2.0, UART, and a QUICC Engine (QE) block for protocol acceleration. What is a PowerQUICC II Pro MPU? It is a 32-bit Power Architecture communications processor System-on-Chip (SoC) that combines a general-purpose e300c2 CPU core with a hardware communications engine. Within the hierarchy PowerPC -> PowerQUICC -> PowerQUICC II Pro -> MPC83xx -> communications SoC, this category is used in small-office/home-office (SOHO) gateways, access equipment, and industrial networking products where deterministic protocol handling offloads the CPU. Key features include 266 MHz e300c2 core, integrated DDR1/DDR2 memory controller, PCI interface, USB 2.0 host/device, multi-channel UART, and a QUICC Engine for HDLC/TDM/ATM-style protocol termination. The family is designed without on-chip encryption (the MPN suffix 'C' denotes non-crypto; 'E' suffix parts add SEC 2.0+ cryptography). The architecture pairs the e300c2 scalar core, built on the classic PowerPC Book-E instruction set, with an on-chip peripheral set that historically replaced external ASIC glue in router, DSLAM, and PBX designs. The QUICC Engine is the key differentiator - a programmable RISC coprocessor that handles up to 32 HDLC channels or TDM links, freeing the host core from bit-banging serial protocols. Typical applications include communication gateways (SOHO router, xDSL, cable modem head-end), industrial control platforms with deterministic networking, embedded Linux HMI systems, edge computing nodes, and protocol-conversion bridges. The wide industrial temperature range of -40C to +105C supports deployment in harsher environments than commercial-grade parts. Design consideration: route the DDR controller address/clock group with controlled impedance and matched length, and isolate the QUICC Engine TDM/HDLC pins from analog sections to avoid coupling from high-speed edges into line interfaces. Refer to the MPC8321E PowerQUICC II Pro Hardware Specifications for reference board stack-up and termination. This page consolidates distributor pricing, parametric comparison vs same-family MPC8321 variants, and practical design notes that go beyond the manufacturer datasheet's narrative description.

طلب عرض سعر اتصل بنا
MPC8321CVRAFDC - PowerQUICC II Pro MPU, e300, 333MHz, 516-PBGA | NXP
MPC8321CVRAFDC

MPC8321CVRAFDC - PowerQUICC II Pro MPU, e300, 333MHz, 516-PBGA | NXP

The NXP (formerly Freescale) MPC8321CVRAFDC is a PowerQUICC II Pro integrated communications microprocessor built on the e300c2 core, delivering 333 MHz performance with a 32-bit data bus in a 516-pin PBGA (HBGA) package. It is part of the non-encryption (W/O ENCR) variant of the MPC8321 family, optimizing cost for designs that do not require the built-in security engine. An MPU (Microprocessor Unit) in this category is the central processing element of an embedded computing system. The PowerQUICC architecture sits in the product hierarchy as: e300 core -> PowerPC family -> PowerQUICC II Pro -> communications MPU -> embedded processor. The MPC8321CVRAFDC integrates a CPU core, memory controller, communications peripherals, and system interfaces on a single die, replacing what previously required an MPU plus a separate communications ASIC. This system-on-chip integration reduces board area, BOM count, and software complexity for networking and industrial equipment. Key features of the MPC8321CVRAFDC include: 333 MHz e300c2 core running the PowerPC instruction set, 32-bit data path, DDR/DDR2 memory controller, dual Gigabit Ethernet MACs (one RGMII, one MII/RGMII), PCI interface, USB, TDM, I2C, SPI, and UART peripherals, integrated security engine (encryption variants only), and 516-pin HiTCE PBGA package. The 'W/O ENCR' suffix explicitly identifies the part as the non-encryption variant for cost-sensitive designs. From an architecture perspective, the e300c2 core implements the PowerPC instruction set with MMU and hardware floating-point support optional. The integrated memory controller supports DDR/DDR2 SDRAM with ECC, enabling robust error handling required in carrier-grade equipment. The communications accelerator engine handles common protocol operations, offloading the CPU and improving packet throughput for routing, switching, and gateway applications. Typical applications include SOHO/SMB routers, integrated access devices (IADs), DSLAMs, Ethernet switches with management, industrial gateways, and networked printers. The 333 MHz clock combined with the integrated Ethernet MACs supports line-rate routing and switching for the SOHO/SMB market. The 516-pin PBGA package provides the I/O density needed to expose multiple high-speed peripherals simultaneously. When designing with the MPC8321CVRAFDC, ensure signal integrity on the DDR memory bus via controlled-impedance routing and matched-length traces. Thermal management is important because 333 MHz operation in a PBGA package requires attention to junction temperature via the exposed thermal interface. Reference the NXP MPC8321E PowerQUICC II Pro Hardware Specifications document for full power, clock, and reset design requirements. This page synthesizes distributor availability, verified pin-compatible drop-in alternatives within the MPC83xx PowerQUICC II Pro family, and practical design notes not found in the manufacturer datasheet, specifically targeted at engineers sourcing long-lead-time or end-of-life communications processors.

طلب عرض سعر اتصل بنا
MPC8321CVRAFDCA557 - 333MHz PowerQUICC II Pro MPU | NXP | 516-PBGA
MPC8321CVRAFDCA557

MPC8321CVRAFDCA557 - 333MHz PowerQUICC II Pro MPU | NXP | 516-PBGA

The NXP MPC8321CVRAFDCA557 is a PowerQUICC II Pro integrated communications processor built around the e300c2 (MPC603e-based) core, delivering 333 MHz of 32-bit processing performance with a dedicated communications engine for networking and embedded connectivity applications. It integrates a 32-bit CPU, dual DDR1/DDR2 memory controllers, PCI, USB 2.0, multiple UARTs, and the QUICC Engine (QE) for protocol acceleration, all in a 516-pin PBGA (27x27 mm) package. A communications System-on-Chip (SoC) integrates one or more processor cores with on-chip peripherals, memory controllers, and protocol engines targeted at networking, telecom, and industrial connectivity applications. The MPC83xx family, including the MPC8321, belongs to the PowerQUICC II Pro tier, balancing cost, performance, and integration for cost-sensitive systems. Within the broader taxonomy, this part is a microprocessor IC (MPU/MCU class), targeting mid-range routing, switching, and industrial gateway designs that need more CPU headroom than simple MCUs but full SoC integration without external glue logic. Key features include: 333 MHz e300c2 core, hardware-accelerated QUICC Engine supporting Ethernet, ATM, HDLC, and other protocols; DDR1/DDR2 memory controller with 16-bit ECC support; PCI 2.3 interface; USB 2.0 (host/device); up to eight UARTs; integrated security engine; and CPM-style interrupt handling. The 516-PBGA package supplies all I/O through a single, dense BGA footprint suitable for multilayer telecom-class PCBs. The device operates from a 950 mV to 1.05 V core supply and 3.0 V to 3.6 V I/O supply, across an industrial -40 °C to +105 °C temperature range, with thermal-aware features and power management. Its architecture combines a general-purpose PowerPC core with a communication-specific coprocessor, allowing it to offload protocol processing from the main CPU while running a full operating system (typically VxWorks or Linux) on the host core. Typical applications include SOHO/SMB routers, integrated access devices, DSLAM line cards, industrial control gateways, and PCI-attached peripheral controllers. The wide peripheral set and integrated security engine make it well-suited for managed switches and protocol-conversion equipment. When designing with the MPC8321, allocate thermal copper and via arrays beneath the PBGA to keep junction temperatures inside the 105 °C rating, and follow NXP's hardware-design guide for DDR termination, PCI impedance, and decoupling. A JTAG debug port is mandatory for board bring-up. This page synthesizes distributor availability, same-family drop-in alternatives, and engineering selection guidance not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا
MPC8321CZQADDC - PowerQUICC II Pro MPU 266MHz PBGA516 | NXP
MPC8321CZQADDC

MPC8321CZQADDC - PowerQUICC II Pro MPU 266MHz PBGA516 | NXP

The NXP MPC8321CZQADDC is a PowerQUICC II Pro communications processor built on a 32-bit PowerPC e300c2 core running at 266MHz, housed in a 516-pin PBGA package (27x27 mm). It integrates a high-performance CPU with communications peripherals and memory interfaces targeted at SOHO routers, access equipment, and industrial control platforms. The device operates from 1.8V/2.5V/3.3V supplies and is fabricated on a 90nm CMOS process. An MPU (Microprocessor Unit) is the central processing subsystem in an embedded system, executing operating-system and protocol-stack code. The PowerQUICC II Pro family sits within NXP's communications-processor taxonomy: MPU -> communications processor -> PowerQUICC -> PowerPC ecosystem -> 32-bit embedded computing. The e300c2 core is a descendant of the classic PowerPC Book E architecture with MMU and 16KB/16KB L1 caches, designed for deterministic real-time packet handling in cost-sensitive networking gear. Key features include the e300c2 core at 266MHz, dual 10/100/1000 Ethernet controllers with TDM support, dual PCI interfaces, USB 2.0 (host/device), DDR1/DDR2 memory controller up to 266MHz, four DMA channels, and an integrated security engine. The device also provides dual UART, dual I2C, SPI, local bus, and GPIO. Unlike the MPC8321E variant, the 'C' (without ENCR suffix per Mouser's description) does not include the hardware encryption accelerator, lowering cost and power for designs that rely on software crypto or external accelerators. Typical applications include small/medium business routers, DSLAM line cards, IP-PBX systems, industrial gateways, and protocol-conversion appliances. The 516-pin PBGA footprint gives ample I/O for parallel local-bus peripherals and multiple PHY connections. When designing, allocate four-layer PCB stack-up with continuous power planes for the DDR2 controller; route DDR traces with matched lengths (within 25 mils) and 50-ohm characteristic impedance. The MPC8321E variant should be chosen if hardware-accelerated IPsec or SSL is required.

طلب عرض سعر اتصل بنا
MPC8321ECZQAFDC - 333MHz PowerQUICC II Pro MPU w/ Encryption | NXP
MPC8321ECZQAFDC

MPC8321ECZQAFDC - 333MHz PowerQUICC II Pro MPU w/ Encryption | NXP

The NXP MPC8321ECZQAFDC is a PowerPC e300c2 based microprocessor in the MPC83xx PowerQUICC II Pro family, operating at up to 333 MHz with a 32-bit data bus, housed in a 516-pin PBGA (27x27 mm) package. The 'E' suffix denotes an integrated security engine (encryption accelerator), and the 'ZQAFDC' suffix encodes the 333 MHz speed grade, the 516-BGA package, and the industrial temperature range. A microprocessor (MPU) is a single-chip CPU that integrates the central processing unit, cache, memory controller and peripheral interfaces onto one die. The MPC8321E sits inside NXP's PowerQUICC II Pro communications-processor hierarchy (MPU -> communications processor -> PowerQUICC -> PowerPC -> embedded processor), giving it a clear role as the system-on-chip for low-cost networking equipment that needs deterministic I/O handling alongside general-purpose computing. Key features include a 333 MHz e300c2 core, dedicated communications engine (QUICC Engine) technology, integrated security (SEC 2.0) for DES/3DES/AES/SHA acceleration, dual 10/100/1000 Ethernet MACs (one RGMII, one MII/RGMII), DDR/DDR2 memory controller, dual PCI interfaces, USB 2.0 Full-Speed, and flexible I/O including UART, SPI, I2C and local bus. Process technology is 90 nm CMOS, with 1.8 V / 2.5 V / 3.3 V mixed I/O voltages. Architecturally the device combines a high-performance e300c2 core with the QUICC Engine subsystem, which offloads DMA, TDM, HDLC, ATM and Ethernet handling. The integrated SEC 2.0 block accelerates IPSec and SSL/TLS without burdening the host CPU, which is critical for VPN gateways and secure SOHO routers. Hardware coherency between core and QUICC Engine reduces software complexity for protocol stacks. Typical applications include small/home office routers, xDSL and cable CPE modems, IP services gateways, IP-PBX systems, industrial control with networking, and secure VPN access equipment. The combination of QUICC Engine, dual gigabit Ethernet, hardware encryption and PCI expansion makes the MPC8321E a single-chip foundation for cost-sensitive secure network appliances. When designing with this part, allocate a 27x27 mm PCB land pattern and provide adequate 4-layer decoupling under the BGA, since high-speed DDR traces and gigabit Ethernet interfaces radiate noise that must be contained. U-Boot or a vendor-provided bootloader is typically used to initialize DDR, PCIe and SEC blocks before Linux takes over. This page synthesizes distributor stock levels, exact verified specs, cross-references and practical design notes that go beyond what the manufacturer datasheet lists in the ordering-information table.

طلب عرض سعر اتصل بنا
MPC8321EVRADDC - PowerQUICC II Pro 266MHz e300c2 SoC | NXP
MPC8321EVRADDC

MPC8321EVRADDC - PowerQUICC II Pro 266MHz e300c2 SoC | NXP

The NXP MPC8321EVRADDC is a PowerQUICC II Pro communications processor based on the PowerPC e300c2 core, integrating a 32-bit RISC architecture at 266 MHz in a 516-pin PBGA package (27x27 mm). As a member of the MPC8323E PowerQUICC II Pro family, this SoC combines a high-performance communications engine with on-chip peripherals including DDR1/DDR2 memory controllers, PCI, USB 2.0, a QUICC Engine (QE), and an integrated security engine (SEC). The MPC8321E is a member of the MPC8323E family of cost-effective network communications processors. A communications processor (also called a network processor or SoC) is an application-specific integrated circuit optimized for executing networking and telecom workloads such as packet routing, encryption, and protocol termination. Within the broader taxonomy, the MPC8321E occupies the position: microprocessor -> communications processor -> SoC -> semiconductor. It targets SOHO routers, IP services gateways, and small-to-medium enterprise access equipment where deterministic throughput and integrated peripherals reduce BOM cost. Key features include hardware-accelerated encryption (SEC) for IPsec/SSL, multi-PHY Ethernet support via the QUICC Engine, and flexible peripheral multiplexing. Operating voltage is 1.0 V core (typical), and the part is rated for the commercial 0C to 105C extended operating range. The 516-PBGA package exposes high-speed serial interfaces, parallel DDR memory bus, and multiple PCI segments for legacy and modern interconnect. Typical applications include broadband CPE, IP-PBX, secure VPN gateways, industrial control with Ethernet, and wireless access points. The integrated security engine accelerates DES/3DES/AES/SHA workloads at line rate without burdening the e300c2 core, making the device suitable for VPN termination and IPsec-accelerated edge routers. When designing with this device, ensure proper decoupling on the 1.0 V core rail and that the DDR2 memory topology follows the Fly-by topology guidelines in the hardware specifications document. JTAG boundary-scan must be enabled for production test access. The lead-free PBGA-516 has a 1.0 mm pitch; PCB designers should plan for microvia stack-ups to fan out the dense BGA. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on standalone manufacturer product pages.

طلب عرض سعر اتصل بنا
MPC8321EVRAFDC - PowerQUICC II Pro MPU 333MHz e300 | NXP
MPC8321EVRAFDC

MPC8321EVRAFDC - PowerQUICC II Pro MPU 333MHz e300 | NXP

The NXP Semiconductors MPC8321EVRAFDC is a PowerQUICC II Pro integrated communications processor based on the e300 core running at 333 MHz, housed in a 516-pin TEBGA (27x27 mm) package. As a member of the MPC83xx family, it integrates a 32-bit Power Architecture SoC with QUICC Engine, PCI, USB 2.0, DDR1/DDR2 memory controller, security engine, and Gigabit Ethernet support on a single die. The part is designed for cost-effective networked communications in SOHO, access, and IP-services applications. What is a PowerQUICC communications processor? A PowerQUICC II Pro device is a system-on-chip (SoC) microprocessor that combines a Power Architecture CPU core with specialized communications peripherals (the QUICC Engine), reducing bill-of-materials cost and board area versus discrete CPU + ASIC designs. It belongs to the broader hierarchy of embedded microprocessors -> communications processors -> PowerQUICC family -> SoC. Key features of the MPC8321EVRAFDC include the e300c2 core at 333 MHz with 32-bit data path, integrated security engine for IPSec/SSL acceleration, dual 10/100/1000 Ethernet controllers, dual USB 2.0 (host + device or dual-host capable), 32-bit/66 MHz PCI interface, DDR1/DDR2 SDRAM controller with ECC, and 16-bit local bus. The 516-ball TEBGA package exposes the full peripheral set while maintaining a 27x27 mm outline suitable for production networking hardware. Architecturally, the device uses a unified memory architecture with a 32 KB instruction cache and 32 KB data cache, a memory management unit, and a dedicated QUICC Engine sub-processor that offloads protocol processing (Ethernet, ATM, HDLC) from the main core. This dual-processor topology enables line-rate throughput on WAN interfaces while the e300 runs Linux or VxWorks for control-plane software. Typical applications include small/home office routers, xDSL/Cable gateways, IP services access points, industrial control with Ethernet, secure VPN concentrators, and network attached storage controllers. The integrated security engine makes it well-suited for VPN/IPSec gateways where line-rate encryption is required without an external crypto ASIC. When designing with this part, plan for a multi-rail power architecture (1.8V core, 2.5V DDR termination, 3.3V I/O) and provide proper DDR2 trace impedance (50 ohm to 60 ohm differential). The 516-ball TEBGA requires multi-layer PCB with microvia technology and matched-length DDR traces; signal integrity on PCI and Ethernet should be validated with TDR measurements.

طلب عرض سعر اتصل بنا
MPC8321EZQAFDC - PowerQUICC II Pro MPU 333MHz | NXP
MPC8321EZQAFDC

MPC8321EZQAFDC - PowerQUICC II Pro MPU 333MHz | NXP

The NXP MPC8321EZQAFDC is a PowerQUICC II Pro integrated communications microprocessor built on the PowerPC e300c2 core, delivering 333 MHz of 32-bit processing performance with integrated encryption acceleration. Housed in a 516-pin PBGA package measuring 27x27 mm, this MPU belongs to the MPC8323E family and targets cost-sensitive networking and industrial applications. What is a PowerQUICC processor? PowerQUICC (pronounced 'power-quick') is NXP's (formerly Freescale) family of communications processors that combine a PowerPC CPU core with a Communications Processor Module (CPM) for offloading networking and peripheral tasks. In the broader taxonomy, the MPC8321E is a microprocessor (MPU) -> embedded processor -> communications processor -> SoC. PowerQUICC II Pro generations like this one integrate security engines (the 'E' suffix denotes encryption-enabled variants), making them foundational for SOHO routers, VPN gateways, and IP services equipment. Key differentiating features include the integrated hardware encryption accelerator (SEC 2.0+), support for DDR1/DDR2 memory up to [DATA_NEEDED: memory size], dual 10/100/1000 Ethernet MACs, and a peripheral set including PCI, USB, and UART. The 333 MHz core frequency combined with the CPM offload engine enables line-rate packet processing without CPU saturation. The encryption engine supports DES, 3DES, AES, and SHA/MD5 hashing, eliminating the need for external crypto chips in VPN and SSL terminator designs. Architecturally, the e300c2 core is a 32-bit PowerPC implementation with MMU and L1 caches, while the CPM handles DMA-driven peripheral channels. This dual-engine design keeps networking throughput consistent regardless of OS overhead on the host CPU. The 516-PBGA package provides ample I/O for parallel peripheral buses and high-speed serial interfaces, but requires careful PCB layout with controlled-impedance routing and thermal management copper pours. Typical applications include small office/home office (SOHO) routers, IP services gateways, DSL/cable modems, industrial control systems, secure print servers, and networked storage appliances. The integrated encryption makes it particularly attractive for VPN concentrators and SSL/IPsec gateway designs where security throughput is critical. When designing with this device, pay close attention to the 27x27 mm PBGA land pattern requirements, JTAG boundary-scan considerations, and the thermal profile under sustained CPM activity. A multi-layer PCB with dedicated power and ground planes is strongly recommended for signal integrity at the DDR memory interface. This page synthesizes distributor pricing, same-family NXP drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. Engineers evaluating MPU options for embedded networking will find the alternatives and comparison data particularly useful when qualifying second sources or planning EOL transitions.

طلب عرض سعر اتصل بنا
MPC8321VRADDC - PowerQUICC II Pro 266MHz SoC | NXP | Networking
MPC8321VRADDC

MPC8321VRADDC - PowerQUICC II Pro 266MHz SoC | NXP | Networking

The NXP MPC8321VRADDC is a PowerQUICC II Pro integrated communications processor that combines a PowerPC e300c2 core running at 266 MHz with an integrated QUICC Engine, PCI, USB 2.0, DDR1/DDR2 memory controller, and dual UART interfaces in a 516-pin PBGA package (27x27 mm). It is a member of the cost-effective MPC8323E family targeting small-office/home-office (SOHO) routing, IP services, access equipment, and secure communications gateways. A PowerQUICC II Pro communications processor is a member of the broader Power Architecture microprocessor family, sitting within the power management and embedded processor hierarchy (CPU -> MPU -> communications SoC -> networking subsystem). The architecture integrates control-plane processing with hardware-accelerated protocol handling so that OEMs can build routers, media gateways, and access multiplexers without discrete peripheral chipsets. Key features include the e300c2 core at 266 MHz, hardware-accelerated QUICC Engine for HDLC/PPP/Ethernet processing, integrated DDR1/DDR2 SDRAM controller with ECC support, 32-bit PCI 2.3 interface, USB 2.0 host/device with on-chip transceiver, dual 10/100 Ethernet MACs, dual UART, and an operating temperature range of 0C to 105C. The 516-pin PBGA package provides the signal density needed for parallel memory, PCI, and Ethernet buses. The device uses a 32-bit Power Architecture (PowerPC) implementation on a 0.13-micron process, with separate system and peripheral clock domains. The QUICC Engine offloads serial-bit handling from the core, freeing CPU cycles for routing protocols and management software while still exposing a unified programming model through UPM and DMA channels. Typical applications include SOHO routers, VPN/IPsec gateways, Ethernet access multiplexers, industrial control with networking, and T1/E1 termination equipment. The lack of on-chip encryption is the primary difference from the MPC8321E variant, making the VRADDC suffix well-suited to designs where crypto acceleration is provided by a companion security ASIC rather than the host CPU. When designing with this part, allocate generous PCB space for the 27 mm PBGA and provide clean power rails for the DDR controller and PLL domains. Reference the Freescale/NXP hardware specification document for boot sequence, JTAG topology, and DDR signal integrity guidelines before laying out the memory interface. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MPC8321VRAFDC - 333MHz PowerQUICC II Pro e300 MPU | NXP
MPC8321VRAFDC

MPC8321VRAFDC - 333MHz PowerQUICC II Pro e300 MPU | NXP

The NXP MPC8321VRAFDC is a 333 MHz PowerQUICC II Pro communications processor featuring a 32-bit Power Architecture e300c2 core, integrated DDR1/DDR2 memory controller, PCI interface, USB 2.0, dual UART, and a QUICC Engine (without encryption) for protocol offload. It is housed in a 516-ball PBGA package measuring 27x27 mm and is targeted at cost-effective SOHO networking, IP services, access, and industrial control applications. The part operates across 0C to 105C and runs from a 1V core supply, with 3.3V I/O tolerance. A PowerQUICC (pronounced "PowerQUICK") communications processor is a specialized microprocessor that integrates a CPU core with communications peripherals such as Ethernet MACs, ATM support, PCI, and serial controllers on a single die. Within the broader hierarchy, the MPC8321VRAFDC sits inside the PowerQUICC II Pro family, which descended from the original PowerQUICC I (MPC860) line. The MPC8321E variant adds hardware encryption; the MPC8321VRAFDC is the non-encryption ("VRAFD" prefix indicates the unencrypted QE version) variant, allowing lower BOM cost for designs that do not need security acceleration. This part is part of NXP's (formerly Freescale) PowerQUICC family of integrated communications processors. Key differentiating specifications of the MPC8321VRAFDC include the 333 MHz e300c2 core, 16 KB L1 instruction cache and 16 KB L1 data cache, on-chip DDR1/DDR2 memory controller supporting up to 1 GB of external memory, two 10/100 Mbps Ethernet interfaces via the QUICC Engine, two USB 2.0 ports (host/device), two PCI controllers, and dual UART. The integrated security engine is absent in this variant, making it suitable for designs where encryption is not required. From an architectural standpoint, the MPC8321VRAFDC integrates the e300c2 core with the QUICC Engine technology block, which handles lower-layer protocol processing offloaded from the CPU. This allows the e300c2 to focus on higher-layer tasks such as routing, security policy, and management. The QUICC Engine supports protocols including HDLC, UART, BISYNC, Transparent, and ATM SAR (when configured), making the part suitable for legacy and modern serial multiplexing workloads. Typical applications for the MPC8321VRAFDC include small office / home office (SOHO) routers and gateways, IP services routers, DSLAM line cards, industrial control and factory automation controllers, and low-end wireless access points. Its combination of integrated Ethernet, USB, PCI, and DDR controller provides a single-chip BOM for cost-sensitive networking equipment. When designing with this device, ensure the 27x27 mm PBGA thermal footprint has sufficient PCB copper area and that the 1V core supply is generated by a high-efficiency buck regulator with adequate transient response. Verify JTAG access is provisioned for board bring-up, and use the NXP CodeWarrior or Linux BSP for software development. This page synthesizes NXP official datasheet specifications, distributor stock and pricing, drop-in alternatives, and practical design notes not found on a single source page.

طلب عرض سعر اتصل بنا
MPC8321ZQADDC - PowerPC e300c2 MPU, 266MHz, 516-PBGA | NXP
MPC8321ZQADDC

MPC8321ZQADDC - PowerPC e300c2 MPU, 266MHz, 516-PBGA | NXP

The NXP (formerly Freescale) MPC8321ZQADDC is a PowerPC e300c2 microprocessor from the MPC83xx PowerQUICC II Pro family, operating at 266 MHz with a single 32-bit core, housed in a 516-ball PBGA package measuring 27x27 mm. This communications-oriented MPU is designed without on-chip encryption acceleration (the 'Z' suffix denotes 'no encryption' variants in the PowerQUICC II Pro nomenclature) and is intended for cost-effective networking and industrial control applications. A PowerQUICC II Pro communications processor is a highly integrated system-on-chip that combines a PowerPC CPU core with a QUICC Engine communications accelerator block. The MPC83xx family sits within the broader hierarchy: PowerPC CPU -> embedded MPU -> microprocessor -> integrated circuit -> semiconductor. These devices are widely deployed in residential gateways, DSLAM line cards, SOHO routers, and industrial control boards where deterministic packet processing and a low bill of materials matter more than raw application-processor performance. Key specifications include a 266 MHz core clock, 32-bit PowerPC e300c2 core with 16 KB instruction cache and 16 KB data cache, dual 10/100/1000 Mbps Ethernet MACs (one RGMII, one MII/RGMII), a DDR1/DDR2 SDRAM memory controller supporting up to 256 MB of addressable memory, and a multi-channel QUICC Engine for HDLC/TDM/ATM termination. The part supports PCI 2.3 and local bus interfaces for glue-less peripheral integration. The architecture uses a built-in QUICC Engine subsystem with multiple RISC communication controllers (typically eight TDM channels, 64 HDLC channels, and an ATM SAR) running independently from the host CPU. This hardware offload architecture allows line-rate packet processing without burdening the e300c2 core, a key differentiator from general-purpose MPUs. Typical applications include small-to-medium business routers, xDSL line cards, industrial Ethernet gateways, smart-grid concentrators, and protocol-conversion bridges. The 27x27 mm 516-PBGA package is optimized for thermal performance in fanless networking chassis, and the device operates across the standard -40C to +85C industrial temperature range. When designing with this part, pay close attention to DDR2 termination and trace impedance, since the integrated memory controller is sensitive to signal integrity. Reserve a JTAG header for boundary-scan debugging during production and provide a robust reset supervisor for power-rail sequencing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical hardware design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا
MPC8321ZQAFDC - PowerQUICC II Pro e300c2 MPU 333MHz | NXP
MPC8321ZQAFDC

MPC8321ZQAFDC - PowerQUICC II Pro e300c2 MPU 333MHz | NXP

The NXP Semiconductors MPC8321ZQAFDC is a PowerPC e300c2 microprocessor (MPU) from the PowerQUICC II Pro family, operating at up to 333 MHz with a single 32-bit core, housed in a 516-pin PBGA package measuring 27x27 mm. The part is supplied without on-chip encryption acceleration, distinguishing it from the MPC8321E variants that include security engine support. It integrates a PowerPC e300 core with the QUICC Engine communications subsystem for networking tasks. A microprocessor (MPU) is an integrated circuit that contains the central processing unit (CPU) plus cache, memory management, and peripheral interfaces but relies on external memory and program storage. The MPC8321ZQAFDC belongs to NXP's PowerQUICC II Pro family, which sits within the broader category of communication processors, a hybrid between general-purpose microcontrollers and dedicated network processors. The hierarchy is MPU -> communication processor -> embedded processor -> semiconductor. PowerQUICC devices are widely used in routers, switches, and industrial control because they combine integer compute with hardware-accelerated protocol handling. Key features include a 333 MHz e300c2 core, integrated DDR1/DDR2 memory controller, dual 10/100/1000 Ethernet MACs via QUICC Engine, PCI support, USB, and a flexible local bus. The 516-PBGA 27x27 mm package provides ample routing density for the multiple high-speed serial interfaces while remaining within the dimensional envelope of standard embedded designs. Architecturally, the MPC8321ZQAFDC combines a PowerPC e300 integer pipeline with the QUICC Engine, a microcoded RISC engine that offloads protocol tasks such as HDLC, ATM, Ethernet bridging, and IPSec without consuming CPU cycles. This heterogeneous dual-engine design enables line-rate packet processing at gigabit speeds while keeping deterministic interrupt latency for control plane tasks, which is why the family is preferred for SOHO router, DSLAM, and IP services gateway designs. Typical applications include SOHO routers, VPN gateways, industrial Ethernet switches, IP-PBX systems, and networked industrial controllers. The wide peripheral mix also suits it for point-of-sale terminals and multifunction printers. The 333 MHz speed grade targets cost-sensitive designs where higher-end 400+ MHz PowerQUICC II Pro parts would exceed BOM budgets. When designing with this MPU, ensure the PCB uses at least 6 PCB layers with controlled-impedance routing for DDR2 memory traces. A 333 MHz PowerPC core is more thermally demanding than a typical ARM Cortex-A5, so a thermal analysis should confirm the 516-PBGA thermal solution stays within junction limits under sustained processing loads. This page synthesizes distributor pricing, drop-in alternatives, and engineering guidance not aggregated on DigiKey or Mouser product pages, helping procurement and design engineers evaluate the MPC8321ZQAFDC against direct and cross-brand drop-in options in one place.

طلب عرض سعر اتصل بنا
MPC8323CVRADDC - 266MHz PowerQUICC II Pro MPU | NXP
MPC8323CVRADDC

MPC8323CVRADDC - 266MHz PowerQUICC II Pro MPU | NXP

The NXP MPC8323CVRADDC is a cost-effective PowerQUICC II Pro integrated communications processor that combines a 32-bit e300c2 core running up to 266 MHz with the QUICC Engine (QE) communications engine, in a 516-pin PBGA package. It targets multi-protocol control applications requiring hardware-accelerated packet handling without the cost of full MPC8323E silicon. A microprocessor (MPU) is a single-chip CPU integrating core, cache, memory controller and peripherals. The MPC8323 belongs to the broader PowerPC/e300 family of embedded processors, sitting under the PowerQUICC II Pro communications-processor sub-family and ultimately under NXP's MPC83xx networking MPU hierarchy. It is designed for router, switch and access-equipment designs that need deterministic wire-speed throughput. Key features include a 266 MHz e300c2 core with 16 KB I-cache and 16 KB D-cache, a QUICC Engine supporting UTOPIA, two multi-channel HDLC controllers, USB 2.0 (FS/HS), PCI 2.3, two 10/100/1000 Mbps Ethernet MACs (GMII/RGMII/RTBI), and a DDR1/DDR2 SDRAM memory controller. Voltage rails are 1.0 V core, 1.8 V/2.5 V DDR, and 3.3 V I/O. Industrial temperature range is -40C to +105C with the CV (commercial/industrial) suffix. The architecture integrates the QE for protocol offload alongside the e300c2 core so that packet processing and routing/OS tasks run in parallel. The 90 nm process, on-chip DMA and dedicated peripheral bridges let designers replace discrete communications ASICs with a single SoC, reducing BOM and PCB area. Typical applications include SOHO routers, xDSL/cable gateways, integrated access devices, multi-protocol control plane cards, and industrial serial-protocol converters. Pair the MPC8323CVRADDC with a PHY (e.g., Marvell Alaska), DDR2 SDRAM, and a NAND/NOR flash boot source for a complete BOM. When designing, allocate sufficient decoupling on all voltage rails (1.0 V, 1.8 V, 2.5 V, 3.3 V), follow NXP's PBGA thermal layout, and validate DDR2 IBIS models. JTAG boundary-scan is supported for board test. This page synthesizes distributor stock, 516-PBGA drop-in alternatives and design considerations beyond the manufacturer datasheet to help engineers shorten sourcing and qualification cycles.

طلب عرض سعر اتصل بنا
MPC8323CVRADDCA - 266MHz PowerQUICC II Pro PBGA-516 | NXP
MPC8323CVRADDCA

MPC8323CVRADDCA - 266MHz PowerQUICC II Pro PBGA-516 | NXP

The NXP (formerly Freescale) MPC8323CVRADDCA is a PowerQUICC II Pro integrated communications processor featuring a 32-bit e300c2 core running up to 266MHz, packaged in a 516-ball PBGA (27x27 mm, 1.0mm pitch). The part integrates a hardware encryption accelerator, DDR1/DDR2 memory controller, USB 2.0, two 10/100/1000 Ethernet MACs (GMII/TBI/RGMII), a QUICC Engine, PCI, and UTOPIA interfaces, targeting cost-effective multi-protocol networking and control applications. A PowerQUICC II Pro processor is a Power-Architecture (Book-E) communications SoC family combining a CPU core, system logic and a programmable protocol engine. The "PowerQUICC" naming traces back to Freescale's original QUICC engine architecture; "II Pro" denotes enhanced CPU performance, faster serial interfaces, and integrated DDR memory support. These parts sit in the broader taxonomy of microprocessor IC > integrated communications processor > networking SoC > embedded MPU. They are commonly used in routers, DSLAMs, customer-premises equipment, industrial gateways, and PCI/USB-attached control boards where deterministic protocol handling matters. Key features of the MPC8323CVRADDCA include 266MHz e300c2 core clock, integrated DDR1/DDR2 SDRAM controller with ECC, dual Gigabit Ethernet MACs with HiP3 GMII/RGMII/TBI support, a programmable QUICC Engine for TDM/UTOPIA/ATM/HDLC/PPP/serial multiplexing, USB 2.0 (full/high speed) on-chip PHY, PCI 2.3 interface, security accelerator (SEC 2.0 with DES/3DES/AES/SHA-1/MD-5), DMA controller, and JTAG/COP debug. The industrial-grade temperature range is -40C to +105C for fanless networking and harsh-environment designs. Hardware specifications are documented in the Freescale/NXP PowerQUICC II Pro MPC8323E family hardware specifications document. The architecture pairs the e300c2 superscalar core with a coherent system bus and dedicated DMA paths to the QUICC Engine, allowing the host CPU to offload time-critical protocol work without consuming interrupt budget. The integrated security engine accelerates bulk cryptography without tying up the core, while PCI, USB, and Ethernet MACs expose the device directly to networking and host-controller chipsets on a typical line card or control blade. Typical applications include broadband gateways, DSLAM line cards, multi-protocol routers, industrial Ethernet switches, networked printing and imaging controllers, and PCI-attached storage controllers. The part is widely designed into long-lifecycle industrial and telecom platforms because of its extended temperature grade and mature Freescale/NXP toolchain (CodeWarrior, Linux BSP). When designing with the MPC8323, allocate a 27x27 mm footprint with 1.0 mm ball pitch, route DDR2 with 50 ohm controlled-impedance traces, and follow the manufacturer's hardware design checklist for power sequencing and thermal pad soldering. The extended-temperature grade parts (suffix "C") are recommended for outdoor and industrial enclosures. This page synthesizes distributor pricing, datasheet specifications, application guidance, and drop-in alternative comparison data not collected in any single vendor listing.

طلب عرض سعر اتصل بنا
MPC8323ECVRADDC - 266MHz PowerQUICC II Pro SoC | NXP
MPC8323ECVRADDC

MPC8323ECVRADDC - 266MHz PowerQUICC II Pro SoC | NXP

The NXP MPC8323ECVRADDC is a 266 MHz PowerQUICC II Pro integrated communications processor featuring an e300c2 core, security engine, USB 2.0, PCI, DDR memory controller, and UTOPIA interface, housed in a 516-pin PBGA (27x27 mm) package. It belongs to the MPC8323E PowerQUICC II Pro family which also includes the MPC8323, MPC8321E, and MPC8321 variants. The MPC8323ECVRADDC suffix encodes the operating conditions: ECC (extended temp -40C to +105C), VR (RoHS), AD (266 MHz core speed), and DC (516 PBGA). A PowerQUICC II Pro is a cost-effective, highly integrated system-on-chip (SoC) targeting wired and wireless communications infrastructure, including SOHO routers, DSLAM line cards, media gateways, and industrial control. Within the NXP processor taxonomy it sits below the PowerQUICC III modules - MPC83xx family -> PowerPC e300 core -> 32-bit communications processor -> communications SoC -> embedded processor. The e300c2 core is a 32-bit Power Architecture core with MMU, on-chip debug (COP/JTAG), and dual-issue pipelining for embedded-class throughput. Key features of the MPC8323ECVRADDC include the integrated security engine (SEC 2.0) supporting DES, 3DES, AES, SHA-1/MD5 hashing, and public-key acceleration; a DDR/DDR2 memory controller with ECC; a USB 2.0 high-speed host/device/OTG controller; two PCI 2.3 interfaces; a UTOPIA-L2 interface for ATM/PHY connectivity; two fast Ethernet controllers (FCCs) supporting 10/100 Mbps; and a QUICC Engine sub-system for TDM, HDLC, and SS7 protocol termination. Typical applications are SOHO/SMB routers and integrated access devices, xDSL line cards in central-office DSLAMs, 2.5G/3G base-station baseband, industrial serial-control gateways, secure VPN appliances, and PCI-based embedded computing boards. The wide -40C to +105C temperature range also supports outdoor industrial enclosures and telecom line-card environments where commercial-grade parts would fail. For design-in, route DDR address/command traces with controlled impedance and length-matching, and place 100 ohm differential termination resistors close to the UTOPIA/PCI signals. The 27x27 mm PBGA requires a multilayer PCB with at least 4 layers for power/ground integrity. Use the JTAG/COP debug port for bring-up; the COP header should be brought out for production test.

طلب عرض سعر اتصل بنا
MPC8323ECVRADDCA - PowerQUICC II Pro SoC 266MHz e300 | NXP
MPC8323ECVRADDCA

MPC8323ECVRADDCA - PowerQUICC II Pro SoC 266MHz e300 | NXP

The NXP MPC8323ECVRADDCA is a PowerQUICC II Pro integrated communications processor in the MPC8323E family, featuring a 32-bit Power Architecture e300 core running at 266 MHz with the QUICC Engine communications subsystem. It is housed in a 516-pin PBGA package (27x27 mm) and supports DDR/DDR2 memory, PCI, USB 2.0, UTOPIA, and an integrated SEC 2.2 cryptographic accelerator. The device operates across an extended industrial temperature range of -40C to +105C and is supplied by combined 1.8V/2.5V/3.3V rails. A PowerQUICC II Pro is a category of integrated communications processor (communications SoC) widely deployed in wired networking equipment such as SOHO routers, DSLAM line cards, IP service gateways, industrial control, and small-office access platforms. It blends a high-performance Power Architecture CPU with on-chip peripheral controllers, a hardware communications engine, and memory/PCI subsystems - effectively replacing what previously required a CPU plus a separate network ASIC, lowering BOM cost and PCB area while increasing deterministic throughput for packet processing. Key features of the MPC8323ECVRADDCA include a single e300c2 core at 266 MHz, the QUICC Engine for multi-protocol support (UTOPIA, ATM, HDLC, POS), a DDR/DDR2 memory controller, integrated SEC 2.2 for hardware-accelerated security (DES, 3DES, AES, SHA, MD5, Kasumi), a USB 2.0 host/device interface with PHY, a 32-bit/66 MHz PCI controller, two 10/100/1000 Mbps Ethernet MACs (one RGMII, one GMII/MII/TBI), and IEEE 1588 timestamping support. The integrated ECC-protected memory controller and TSEC Ethernet controllers deliver line-rate packet handling for branch-office and customer-premises equipment. Typical applications include integrated access devices, SOHO and SMB routers, DSL and cable modems, WiMAX customer-premises equipment, IP-PBX systems, industrial gateways, and PCI/PCI-X expansion cards. The QUICC Engine offloads protocol processing so the e300 core can run routing stacks and management software without throughput loss. When designing with this device, plan careful power-rail decoupling (1.0V core, 1.8V/2.5V DDR, 2.5V/3.3V I/O) and follow NXP's Hardware Specifications document for sequencing. Place 516-BGA decoupling capacitors as close as possible and provide thermal vias under the exposed die area for heat dissipation in sealed enclosures. This page synthesizes distributor inventory, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MPC8323ECVRAFDC - 333MHz PowerQUICC II Pro MPU | NXP | BGA-516
MPC8323ECVRAFDC

MPC8323ECVRAFDC - 333MHz PowerQUICC II Pro MPU | NXP | BGA-516

The NXP Semiconductors MPC8323ECVRAFDC is a PowerPC e300c2-based PowerQUICC II Pro integrated communications microprocessor with a 333 MHz maximum core clock, one core, 32-bit architecture, and a 516-ball PBGA (27x27 mm) package. It belongs to the MPC8323E PowerQUICC II Pro family and combines a communications engine with a high-performance host CPU plus DDR memory, PCI, USB 2.0, UTOPIA, and SEC acceleration peripherals. What is a PowerQUICC communications processor? PowerQUICC (pronounced "power-quick") is NXP/Freescale's brand name for PowerPC-based system-on-chip devices that integrate a host CPU with one or more communications engine modules (CEs) used in networking, telecom, and embedded routing equipment. Within the family hierarchy, the MPC8323E sits between the lower-end MPC8321E and higher-end MPC8349E parts, providing a cost-effective balance of CPU performance and wired/wireless communications peripherals for SOHO/SME routers, DSLAM line cards, wireless base stations, and industrial control planes. Key differentiating features of this part include 333 MHz e300c2 core clock, hardware encryption acceleration via the SEC engine, dual 10/100/1000 Ethernet MACs, USB 2.0 host/device, PCI 2.3 interface, DDR1/DDR2 memory controller, UTOPIA-LVD interface for xDSL/ATM/PHY connectivity, and an extended operating temperature range of -40C to +105C suitable for industrial and outdoor networking deployments. At the architecture level the MPC8323E pairs the e300c2 host CPU with a separate QUICC Engine communications controller, allowing wire-speed packet processing on dedicated hardware while the host CPU runs control-plane software (Linux, VxWorks, or MQX). DDR1/DDR2 support with ECC, hardware PCI arbitration, and integrated PHYs reduce total BOM cost for line-card and CPE designs. Typical applications include SOHO/SMB routers, xDSL/PON integrated access devices (IADs), Wi-Fi access points with packet inspection, industrial Ethernet gateways, and printer/imagery controllers that benefit from hardware encryption acceleration. The industrial -40C to +105C grade allows deployment in outdoor enclosures. When designing with the MPC8323ECVRAFDC, allocate a minimum 4-layer PCB with a solid ground plane under the 27x27 mm BGA-516 footprint, follow the DDR termination guidelines in the MPC8323E hardware specifications document, and ensure adequate airflow because the part can dissipate several watts under peak Ethernet traffic. Use the UTOPIA-LVD bus only with PHY devices that support the same voltage class (typically 3.3 V LVD). This page synthesizes distributor availability, drop-in alternative candidates, and practical hardware-design notes not found in the standalone datasheet.

طلب عرض سعر اتصل بنا
MPC8323EVRAFDC - 333MHz PowerQUICC II Pro MPU | NXP | BGA-516
MPC8323EVRAFDC

MPC8323EVRAFDC - 333MHz PowerQUICC II Pro MPU | NXP | BGA-516

The NXP MPC8323EVRAFDC is a PowerPC e300c2 microprocessor from the PowerQUICC II Pro family, integrating a single 32-bit core running up to 333 MHz with a 516-pin FPBGA (27x27) package designed for embedded communications. The 'E' suffix denotes the enhanced variant that adds the QUICC Engine (QE) for hardware-accelerated protocol termination, along with integrated peripherals including PCI, USB 2.0, DDR memory controller, UTOPIA, and a security engine (SEC). An MPU (Microprocessor Unit) is a System-on-Chip (SoC) class processor that integrates a CPU core, memory controller, and a rich peripheral set on a single die. Within the broader taxonomy, an MPU sits above a microcontroller (MCU) in integration depth and above a discrete CPU in functional completeness, and is typically classified as an embedded processor or communications processor when paired with protocol engines like the QE block here. Key features of the MPC8323EVRAFDC include the PowerPC e300c2 core with 16 KB I-cache and 16 KB D-cache, a DDR1/DDR2 SDRAM memory controller with ECC, two 10/100/1000 Mbps Ethernet MACs (GMII/RGMII/TBI), a USB 2.0 Full/High-Speed controller, a 32-bit PCI 2.3 interface, the QUICC Engine supporting UTOPIA-L2 / POS-PHY / TDM / HDLC / ATM / Ethernet, an integrated Security Engine (SEC 2.0) for DES/3DES/AES/SHA/RSA, and a 0 to 105 °C commercial operating temperature range. The 'DC' suffix indicates a 27x27 mm FPBGA package, while 'R' indicates tape-and-reel packaging. Architecturally, the device uses a 16-bit DDR memory controller bus, separate address and data buses, and the QE block that offloads protocol processing from the e300c2 core to dedicated RISC engines. This dual-core approach (e300c2 + QE RISC) is what enables the MPC8323E to sustain wire-speed packet processing on multiple T1/E1 channels or a UTOPIA bus while leaving the host CPU free for control-plane software. Typical applications include industrial routers and gateways, wired and wireless access concentrators, VoIP and IP-PBX systems, DSLAM line cards, industrial control and automation equipment, and secure communications appliances. Designers select the MPC8323E for cost-effective multi-channel TDM aggregation, IPsec/SSL acceleration via the SEC engine, and PCI-based expansion to legacy telecom backplanes. When designing with this device, ensure the 27x27 mm FPBGA PCB footprint has adequate via-in-pad or via-array escape routing and at least four PCB layers with dedicated power planes. The DDR controller requires matched-impedance trace lengths and 50-ohm controlled impedance for USB 2.0 High-Speed signaling, both of which are essential for reliable operation at industrial temperature extremes. This page synthesizes distributor pricing, package details, and application guidance for the MPC8323EVRAFDC, drawing on manufacturer datasheets and authorized distributor listings rather than relying solely on the manufacturer brief.

طلب عرض سعر اتصل بنا
MPC8323EZQADDC - PowerQUICC II Pro 266MHz MPU | NXP | Networking
MPC8323EZQADDC

MPC8323EZQADDC - PowerQUICC II Pro 266MHz MPU | NXP | Networking

The NXP (formerly Freescale) MPC8323EZQADDC is a PowerQUICC II Pro Integrated Communications Processor featuring a PowerPC e300c2 core running at 266 MHz, packaged in a 516-ball FPBGA (27x27 mm). It targets cost-effective, highly integrated communications platforms with hardware encryption (the "ADDC" suffix encodes encryption + dual-role enable), DDR1/DDR2 memory controller support, and the classic PowerQUICC peripheral set. This device belongs to the family of PowerQUICC communications processors, a class of integrated circuits that combine a PowerPC CPU core with dedicated communications engine blocks (QUICC Engine), memory controllers, and peripheral I/O. In the broader taxonomy, the MPC8323E ranks as: PowerQUICC II Pro -> PowerQUICC family -> communications processor -> microprocessor -> integrated circuit. The processor's hardware acceleration, security engine, and integrated peripheral set make it a drop-in solution for SOHO/SMB routers, DSL gateways, and industrial control platforms. Key features include 32 KB instruction and 32 KB data L1 caches, a 32-bit DDR1/DDR2 SDRAM memory controller, two 10/100/1000 Mbps Ethernet controllers with GMII/TBI support, USB 2.0 (Full/Low speed), PCI revision 2.3, local bus, SPI, I2C, UARTs, and a security engine (SEC 2.0) supporting DES/3DES/AES/SHA-1/MD-5/RSA. The "Q" suffix indicates the part operates from -40C to +105C extended temperature range. Architecturally, the MPC8323E pairs the e300c2 CPU with a 32-bit QUICC Engine subsystem that offloads networking tasks, a DDR1/DDR2 controller with ECC, and an integrated system bus. The hardware crypto engine accelerates IPSec/SSL/TLS workloads without CPU intervention, which is critical at the 266 MHz clock where software crypto would saturate the CPU. Typical applications include SOHO/SMB routers, integrated DSL/cable gateways, Wi-Fi access points with VPN, industrial control and SCADA platforms, and security appliances (firewalls/VPN concentrators). The wide peripheral integration reduces BOM cost in space-constrained designs. When designing with this part, ensure the DDR2 memory traces are length-matched to within 25 mils per byte lane; pay close attention to the 27x27 mm BGA fan-out for power and ground via stitching under the die shadow.

طلب عرض سعر اتصل بنا
MPC8323VRADDC - PowerQUICC II Pro 266MHz e300 SoC | NXP
MPC8323VRADDC

MPC8323VRADDC - PowerQUICC II Pro 266MHz e300 SoC | NXP

The NXP (formerly Freescale) MPC8323VRADDC is a PowerQUICC II Pro integrated communications processor that combines a 266 MHz e300c2 Power Architecture core with a high-throughput communications engine, housed in a 516-pin PBGA (27x27 mm) package. A PowerQUICC II Pro SoC is a cost-effective network communications processor built on a 32-bit Power Architecture core. It integrates dedicated peripheral engines (QUICC Engine for multi-protocol handling, DDR1/DDR2 memory controller, PCI, USB 2.0, UTOPIA, and 10/100/1000 Ethernet MACs) to offload communication workloads from the host CPU. This architecture sits in the broader hierarchy of embedded processors: MPU -> communications processor -> SoC -> networking ASIC replacement. Key features of the MPC8323VRADDC include 266 MHz core frequency, integrated QUICC Engine for protocol termination, DDR1/DDR2 SDRAM controller, 32-bit PCI 2.2 interface, USB 2.0 (host/device/OTG), UTOPIA interface for ATM/POS PHY connection, dual 10/100/1000 Ethernet MACs with GMII/RGMII support, 0C to 105C commercial operating temperature range, and JTAG boundary scan. The 516-BGA package provides extensive I/O for the integrated peripherals while keeping board area manageable. Technically, the device pairs an e300c2 core (a Power Architecture descendant of PowerPC 603e) with the QUICC Engine coprocessor that runs microcode for HDLC, PPP, Ethernet, ATM, and other protocols, leaving the host CPU free for application and control-plane tasks. Integrated security includes SEC 2.0 (with optional encryption accelerator variants in the MPC8323E family). Typical applications include DSLAM line cards, Ethernet-to-ATM gateways, industrial routers, integrated access devices (IAD), VoIP media gateways, and small-to-medium business networking equipment. The wide peripheral mix also suits POS terminals and industrial control with networking. When designing with this part, ensure the PCB layout allocates adequate BGA escape routing and that the DDR2 controller termination is configured per the reference manual; the QUICC Engine firmware is loaded from a local Flash and must match the silicon revision. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, and complements the NXP MPC8323E PowerQUICC II Pro Reference Manual.

طلب عرض سعر اتصل بنا
MPC8323VRADDCA - PowerQUICC II Pro 266MHz SoC | NXP
MPC8323VRADDCA

MPC8323VRADDCA - PowerQUICC II Pro 266MHz SoC | NXP

The NXP MPC8323VRADDCA is a PowerQUICC II Pro integrated communications processor that combines a 266 MHz e300c2 CPU core with a wide range of communications peripherals, including PCI, USB 2.0, DDR1/DDR2 memory controller, UTOPIA, and a QUICC Engine UCC subsystem. Housed in a 516-pin PBGA package (27 x 27 mm), the device is positioned for cost-sensitive multi-protocol control and networking applications such as SOHO routers, DSLAM line cards, industrial gateways, and wire-line access equipment. The silicon integrates a 32-bit Power Architecture core with a hardware MMU, 16 KB instruction and 16 KB data caches, and a flexible peripheral set that historically replaced several discrete components on the access-aggregation board. A PowerQUICC processor is a member of the broader communications processor family that sits between a microcontroller and a full network processor on the system hierarchy: PowerQUICC II Pro -> PowerQUICC family -> communications processor -> embedded microprocessor -> integrated circuit. PowerQUICC II Pro specifically adds DDR1/DDR2 support, a faster e300 core, USB 2.0 and PCI interfaces, and a more capable QUICC Engine for protocol termination. Understanding this taxonomy helps engineers reading collateral from legacy Freescale / NXP documents, where PowerQUICC I, II, II Pro, and III parts are often referenced side-by-side. Key features include 266 MHz core frequency, integrated DDR1/DDR2 SDRAM controller with ECC, dual 10/100/1 Gb capable Ethernet MACs (via the QUICC Engine), USB 2.0 host/device, PCI 2.2 interface, UTOPIA / xGMII glue-less PHY interfaces, and 32-bit local bus. The on-chip QUICC Engine supports up to eight UCCs running multi-protocol firmware for HDLC, PPP, ATM, and Ethernet bridging. Security is handled by hardware-assisted acceleration for DES, 3DES, AES, SHA-1/MD5, and a true random number generator on the MPC8323E variant. Architecturally the MPC8323 is built on a 0.13-micron process with a 1.0 V core supply and 3.3 V I/O. Power consumption typically falls in the 2.5 W to 4.5 W range depending on frequency, traffic load, and which peripherals are enabled. The QUICC Engine and CPU operate on separate internal power islands, allowing unused UCCs to be clock-gated. Typical applications include SOHO routers, integrated access devices, xDSL line cards, industrial control gateways, factory-floor protocol bridges, and low-density wireless backhaul baseband cards. The MPC8323VRADDCA is the 0 to 105C commercial-temperature variant, making it suitable for thermally-controlled indoor enclosures. A key design consideration is power sequencing: the 1.0 V core voltage must be brought up before the 3.3 V I/O supply, and RESET must remain asserted until both rails are stable. The integrated DDR controller requires careful impedance-matched routing and a matched-length address/command group to avoid signal-integrity issues at 266 MHz. This page synthesizes distributor pricing, drop-in alternatives, datasheet pinout, and engineer-grade design notes that go beyond the manufacturer product page. References to the official datasheet (82 pages) and the NXP end-of-life notification help procurement and design engineers plan a transition strategy for long-life-cycle programs.

طلب عرض سعر اتصل بنا
MPC8323VRAFDCA - PowerQUICC II Pro 333MHz SoC | NXP
MPC8323VRAFDCA

MPC8323VRAFDCA - PowerQUICC II Pro 333MHz SoC | NXP

The NXP Semiconductors MPC8323VRAFDCA is a PowerQUICC II Pro integrated communications processor based on the e300c2 core, operating at up to 333 MHz in a 516-pin PBGA (27x27 mm, 1 mm pitch) package with an industrial 0C to 105C temperature range. It integrates a 32-bit Power Architecture CPU, DDR1/DDR2 memory controller, USB 2.0, PCI, UTOPIA, and a QUICC Engine communications accelerator on a single die. A communications SoC (System-on-Chip) integrates a CPU core, memory controller, and specialized I/O peripherals onto one silicon die. The MPC8323E family sits within the broader NXP PowerQUICC taxonomy: PowerQUICC II Pro -> PowerQUICC family -> communications processors -> 32-bit embedded processors. This integration reduces board area, BOM cost, and design complexity for networking and access equipment compared with discrete CPU-plus-ASIC solutions. Key features include hardware-accelerated protocol handling via the QUICC Engine, support for DDR1/DDR2 SDRAM up to 333 MHz, dual 10/100/1000 Ethernet MAC interfaces, USB 2.0 host/device, PCI 2.3, and a 27x27 mm 516-ball PBGA package designed for industrial-grade thermal performance. The device supports industrial temperature operation from 0C to 105C and is lead-free / RoHS compliant. The MPC8323E architecture combines the e300c2 superscalar Power Architecture core with the QUICC Engine, offloading bit-level protocol tasks from the CPU. This separation enables deterministic throughput for packet processing, encryption, and ATM/PPP/MLPPP framing while the core handles control-plane software stacks. The DDR1/DDR2 controller supports up to 333 MHz operation for high-bandwidth memory access. Typical applications include SOHO routers, xDSL/ISDN access concentrators, IP service gateways, industrial control, and VoIP platforms where deterministic communication throughput is required. The QUICC Engine is particularly suited to ATM, TDM, and Ethernet bridging. When designing with this device, careful attention must be paid to power sequencing, DDR memory trace length matching, and thermal management. The 27x27 mm PBGA requires a 6-layer or 8-layer PCB stack-up with continuous ground planes for signal integrity and adequate copper area for heat spreading. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes for the MPC8323VRAFDCA, information that goes beyond the manufacturer datasheet to support sourcing and design decisions.

طلب عرض سعر اتصل بنا
MPC8323ZQADDC - 266MHz PowerQUICC II Pro MPU | NXP 516-PBGA
MPC8323ZQADDC

MPC8323ZQADDC - 266MHz PowerQUICC II Pro MPU | NXP 516-PBGA

The NXP MPC8323ZQADDC is a PowerQUICC II Pro integrated communications processor built around the e300c2 core running at up to 266 MHz, packaged in a 516-ball PBGA (27 x 27 mm). It is a 32-bit single-core MPU from the MPC83xx family designed for cost-effective multi-protocol network control and routing applications. The ZQADDC suffix indicates the 266 MHz speed grade without encryption acceleration (no SEC engine), distinguishing it from the MPC8323E variants. An MPU (Microprocessor Unit) is a programmable processor that executes operating systems and application software, sitting at the top of the embedded system hierarchy: MPU -> microprocessor -> processor -> integrated circuit -> semiconductor. MPC8323 devices differ from MCUs in that they require external memory (DDR SDRAM, flash/NOR) and provide richer peripheral integration for telecom/datacom line cards. Key features include a 32-bit PowerPC e300c2 core with MMU and unified L1 caches, a dedicated communications processor module (CPM) with multiple FCC, MCC, SCC, SMC and SPI serial controllers, dual 10/100/1000 Ethernet MACs (eTSECs), DDR1/DDR2 memory controller, PCI Express / PCI interface, and a 32-bit local bus. The 266 MHz core delivers approximately 0.5 DMIPS/MHz of integer performance. Technically, the device integrates QUICC Engine technology for hardware-accelerated protocol termination (Ethernet, HDLC, ATM, UART), offloading the host core. It supports boot from NOR flash or I2C EEPROM, has JTAG boundary-scan for test, and operates across an extended industrial temperature range with typical core voltages around 1.2 V and I/O at 3.3 V. Typical applications include low-end to mid-range routers, DSLAM line cards, industrial gateways, network-attached storage controllers, and wireless base-station control plane processors. The device is particularly attractive for legacy PowerQUICC designs migrating from MPC8272/MPC8280 families where software compatibility is preserved. When designing with this MPU, allocate sufficient PCB area for the 27 x 27 mm PBGA; use at least 4-layer stack-up with continuous ground planes under the BGA. Decouple the core and DDR rails with low-ESR ceramic capacitors placed as close as possible to the BGA balls. This page synthesizes distributor pricing, drop-in MPC83xx alternatives, and practical design guidance not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا
MPC8343CVRADDB - PowerQUICC II Pro SoC, 266MHz, 620-BGA | NXP
MPC8343CVRADDB

MPC8343CVRADDB - PowerQUICC II Pro SoC, 266MHz, 620-BGA | NXP

The NXP MPC8343CVRADDB is a PowerPC e300 microprocessor integrated into the PowerQUICC II Pro family, delivered as a system-on-chip (SoC) in a 620-pin BGA (HBGA, 29x29 mm) package. It runs at 266 MHz on a 32-bit data bus and integrates DDR1/DDR2 memory controllers, dual Gigabit Ethernet MACs, dual PCI interfaces, and Hi-Speed USB controllers. The device is specified over an industrial -40C to +105C temperature range and operates from 1.2V core supply with 1.8V/2.5V/3.3V I/O support. A PowerQUICC II Pro processor is an integrated communications processor that combines a Power Architecture (PowerPC) CPU core with on-chip peripheral controllers. It belongs to the MPU (microprocessor unit) category and sits in the broader SoC taxonomy as a system-on-chip for embedded networking and storage applications. The MPC8343E family extended the earlier PowerQUICC II line by adding faster DDR memory support and dual-gigabit Ethernet, enabling wire-speed routing, NAS, and RAID system designs without external bridge chips. Key features include a 266 MHz e300 core, dual 10/100/1000 Mbps Ethernet controllers with QoS, dual PCI 2.3 buses, USB 2.0 Hi-Speed host/device, DDR1/DDR2 memory controller with ECC, and integrated security engines (the “E” variant includes encryption acceleration). The 620-HBGA package exposes extensive GPIO and high-speed serial interfaces, allowing direct connection to external PHYs, DIMM sockets, and expansion buses without glue logic. The architecture pairs the e300 superscalar core with a dedicated communications processor module (CPM), allowing protocol handling to run independently of application code. This dual-engine topology is the technical foundation behind PowerQUICC’s long-standing role in routers, DSLAMs, and RAID controllers where deterministic packet throughput is required alongside general-purpose Linux or VxWorks processing. Typical applications include wired routers and gateways, RAID storage controllers, industrial control PCs, factory automation controllers, and networked printers. The wide peripheral set also makes the MPC8343 suitable for medical imaging gateways and defense/aerospace embedded subsystems that require long-lifecycle silicon and wide-temperature operation. When designing with this device, allocate PCB area for the 29x29 mm BGA and plan a 6-to-8 layer stack-up with microvia or via-in-pad technology to fan out all 620 balls. Thermal management is required because the SoC can dissipate several watts under full peripheral load. This page synthesizes NXP product information, distributor stock status, drop-in compatible PowerQUICC variants, and design considerations that go beyond the manufacturer datasheet, helping engineers evaluate replacement risk and second-source options.

طلب عرض سعر اتصل بنا