المنتجات (44,000+)

MSP430V138TDA Flash Embedded MCU | Texas Instruments
MSP430V138TDA

MSP430V138TDA Flash Embedded MCU | Texas Instruments

The Texas Instruments MSP430V138TDA is an active, flash-programmed embedded microcontroller intended for mixed-signal, low-power, and connected embedded systems. It belongs to the MSP430 family of 16-bit RISC microcontrollers, combining a microcontroller core, on-chip program and data memory, analog measurement resources, timers, communication interfaces, and low-power operating modes in one integrated device. The exact electrical ratings, memory organization, clock architecture, peripheral configuration, pin assignments, and package dimensions should be confirmed in the manufacturer datasheet before schematic capture or PCB layout begins. What is an embedded microcontroller? An embedded microcontroller is a semiconductor that combines a processor core with memory, input/output ports, and dedicated peripherals in one package. The processor executes application firmware, while the peripherals handle measurements, timing, data exchange, and control functions. Within the product hierarchy, the MSP430V138TDA is a microcontroller, which is a type of integrated circuit and embedded processor. It can serve as the central controller in instrumentation, industrial monitoring, building automation, portable measurement equipment, and connected sensor systems. The MSP430V138TDA is identified as a flash-programmed MCU, allowing operating firmware to be programmed and updated in the device rather than relying on mask-programmed ROM. That architecture is useful for products that require configurable control logic, field diagnostics, calibration support, or firmware revision management. Designers should map each firmware function to the specific peripherals and interrupt resources listed in the datasheet, then verify clock, memory, and interface requirements against the product specification. Its mixed-signal capability makes the MCU relevant to designs that measure analog quantities and perform digital control in the same enclosure. Common implementation choices include sensor signal acquisition, digital control of power converters, metering, low-level communications, and autonomous data collection. For each of these applications, correct sensor conditioning, reference selection, input protection, and isolation remain essential; the microcontroller does not replace front-end analog design. Low-power operation is a defining consideration in MSP430-based products. The MSP430 architecture is commonly used with duty-cycled control loops, sleep modes, and wake-up events to reduce energy use in battery-operated equipment. Actual active and standby current must be checked at the selected voltage, temperature, clock configuration, and peripheral state. Peripheral gating and firmware execution patterns can materially change system energy consumption, so a datasheet current value should not be treated as an end-to-end application result. The MSP430V138TDA is offered in a package identified by the TDA ordering suffix. Use the package drawings, land pattern, pin-description table, and recommended PCB layout guidance in the manufacturer documentation rather than inferring dimensions from the suffix. The exposed-pad arrangement, if present, must be connected according to the datasheet and thermal requirements. This product page combines the verified manufacturer identity, active lifecycle status, flash-programmed MCU classification, source links, application guidance, and a strict drop-in alternative review. Because the available material does not establish pin-compatible substitutes, unverified candidates are excluded. Use the Request a Quote form for current commercial availability, and request the complete manufacturer documentation before committing the part to a production design.

طلب عرض سعر اتصل بنا
MSP432E401Y - 120MHz Cortex-M4F Ethernet MCU, 1MB Flash | TI
MSP432E401Y

MSP432E401Y - 120MHz Cortex-M4F Ethernet MCU, 1MB Flash | TI

The Texas Instruments MSP432E401Y is a SimpleLink 32-bit Arm Cortex-M4F Ethernet microcontroller running at 120 MHz, with 1 MB (1M x 8) of on-chip flash and 256 kB of SRAM, housed in a 128-TQFP (14 x 14 mm) surface-mount package. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals into one package. It sits at the heart of the embedded hierarchy: microcontroller unit -> embedded processor -> semiconductor device. The MSP432E401Y belongs to the SimpleLink MCU platform, which spans Wi-Fi, Bluetooth low energy, Sub-1 GHz, Ethernet, Zigbee, Thread, and host MCUs - all sharing a common, easy-to-use development environment with a single core software development kit (SDK) and rich tool set. Key features include the 120 MHz Cortex-M4F core with a hardware floating point unit (FPU) and DSP instructions, 1 MB flash for code storage, 256 kB SRAM for buffers and stacks, and an integrated 10/100 Ethernet MAC and PHY that enables a single-chip networked node without an external PHY. CAN 2.0 support addresses industrial fieldbus requirements. Technically, the MSP432E401Y uses the Arm Cortex-M4F architecture with an advanced interrupt architecture, and its peripheral memory map is shared across the MSP432E4 family as documented in the MSP432E4 Technical Reference Manual (Rev. A). This simplifies software porting between family members and from the legacy TM4C129 series, which is confirmed as pin-to-pin compatible on the TQFP packages per TI E2E forum guidance. Typical applications include industrial Ethernet gateways and IoT nodes, IEEE 1588 PTP precision timing masters, building automation and remote monitoring nodes, and CAN-based industrial control - anywhere cost-sensitive control processing plus wired connectivity is required. The MSP-EXP432E401Y LaunchPad kit provides a fast evaluation path. Design consideration: when migrating from TM4C129x devices, the pinout is pin-to-pin compatible, but software must move to the SimpleLink SDK; TM4C129 MCUs are not part of the SimpleLink family and do not offer its connectivity ecosystem. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MSP432E411YTZADR - 120MHz Cortex-M4F MCU 1MB Flash | Texas Instruments
MSP432E411YTZADR

MSP432E411YTZADR - 120MHz Cortex-M4F MCU 1MB Flash | Texas Instruments

The Texas Instruments MSP432E411YTZADR is a SimpleLink™ 32-bit Arm Cortex-M4F microcontroller (MCU) with floating-point unit, integrating 1MB Flash and 256kB SRAM in a 212-ball NFBGA (ZAD) 10x10mm package. It operates at up to 120MHz and includes an integrated Ethernet MAC+PHY, dual CAN controllers, USB Host/Device, and a TFT LCD interface for graphics-capable applications. Per TI's product page, the device is qualified for an industrial operating temperature range of -40C to +105C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of peripherals such as timers, ADCs, and communication interfaces. The MSP432E411Y belongs to the SimpleLink MCU family (32-bit MCU -> Arm Cortex-M -> embedded microcontroller -> microcontroller/system-on-chip hierarchy), positioned as a deterministic, real-time control + connectivity platform for industrial, IoT, and human-machine interface (HMI) products. Key features highlighted by the verified data include: 120MHz Cortex-M4F core with single-precision FPU, 1MB on-chip Flash (1M x 8), 256kB SRAM, integrated 10/100 Ethernet MAC+PHY with MII/RMII, two CAN 2.0 A/B controllers, USB 2.0 OTG (Host/Device), 8/16/32-bit external peripheral interface (EPI) for SDRAM/SRAM/FPGA connection, and a TFT LCD controller with dedicated DMA. The 212-NFBGA package provides 212 balls at 0.65mm pitch within a compact 10x10mm outline, suitable for space-constrained designs that demand maximum peripheral integration. Architecturally, the device pairs the Cortex-M4F core with a deterministic interrupt controller, configurable GPIO, four 32-bit timers, dual 12-bit ADCs up to 2 MSPS, and an Hibernation module with RTC and backup battery support for ultra-low-power sleep. The integrated Ethernet MAC+PHY, hardware crypto accelerator (AES/SHA/MD5/CRC), and ECC-protected memory make it a strong choice for secure, connected embedded systems. Typical applications include industrial Ethernet gateways, programmable logic controllers (PLCs), building automation controllers, HMI panels with TFT displays, barcode scanners, point-of-sale (POS) terminals, and connected IoT edge nodes. The combination of Ethernet, CAN, USB and TFT LCD interfaces removes the need for most external bridge chips. When designing with this device, allocate PCB area for the 212-ball NFBGA land pattern with 0.65mm ball pitch - this requires laser-cut solder stencils and careful reflow profiling. Bypass the 12 V-tolerant analog and digital supply pins with 100 nF + 10 uF ceramic capacitors placed as close as possible to the balls. This page synthesizes distributor pricing, drop-in alternative references, and practical application guidance that the manufacturer datasheet alone does not present, enabling faster BOM selection for industrial and connected designs.

طلب عرض سعر اتصل بنا
MSP432P401MIRGCR - 48MHz ARM Cortex-M4F MCU 128KB Flash | Texas Instruments
MSP432P401MIRGCR

MSP432P401MIRGCR - 48MHz ARM Cortex-M4F MCU 128KB Flash | Texas Instruments

The Texas Instruments MSP432P401MIRGCR is a SimpleLink ultra-low-power 32-bit ARM Cortex-M4F microcontroller with FPU, operating at up to 48 MHz, integrating 128 KB of Flash and 32 KB of SRAM in a 64-pin VQFN (RGC) 9x9 mm package. The device is built on a precision-mixed-signal architecture that includes a 14-bit 1 MSPS SAR ADC with internal voltage reference, multiple serial interfaces (UART/SPI/I2S), and up to 48 GPIO pins. The Cortex-M4F core delivers DSP instructions and a single-precision floating-point unit for signal-processing workloads while the MSP432 platform achieves 80 µA/MHz active power consumption. The 'I' industrial temperature grade operates from -40 °C to +85 °C at a supply voltage of 1.62 V to 3.7 V. A SimpleLink MSP432P401x microcontroller is an ultra-low-power ARM Cortex-M4F MCU designed for battery-powered and energy-harvesting applications. The platform combines Cortex-M4 DSP performance with MSP430-class power efficiency, featuring seven low-power modes (LPM0-LPM4.5) that draw sub-µA standby current. The MSP432 family occupies the tier between 16-bit MSP430 devices and higher-power Cortex-M4 parts, and is positioned within the SimpleLink ecosystem of compatible wireless host MCUs that share drivers, RTOS support (TI-RTOS, FreeRTOS), and the CCS development environment. Key features include 128 KB single-cycle Flash with 4-bank partitioning for in-field updates, 32 KB SRAM with parity, four 16-bit timers, two 32-bit timers, a 14-bit 1 MSPS SAR ADC with 16 channels and internal 1.2 V or 1.45 V reference, plus two comparators. The RGC package integrates a 9 mm × 9 mm VQFN with exposed thermal pad. Hardware cryptography acceleration and AES are absent on the M-class part (these are reserved for MSP432P401R higher-tier SKUs). The MSP432P401M uses a Cortex-M4F core with MPU and FPU, supported by an integrated 8-channel DMA engine, SysTick timer, and a flexible clock tree with 48 MHz DCO, 32.768 kHz LFXT, and an internal REFO. On-chip peripherals include RTC, watchdog, and supply-voltage supervisor. The 14-bit ADC achieves 1 MSPS throughput with 16 single-ended or differential channels. The architecture nests balanced supplies with deep-sleep LPM3.5 current under 1 µA typical. Typical applications include industrial sensor transmitters, smart metering endpoints, IoT edge nodes, building automation controllers, HVAC sensor interfaces, battery-powered medical monitors, and consumer wearables. The integrated precision ADC removes the need for an external converter in many sensor-conditioning designs. Designers should budget for the 9 mm × 9 mm VQFN PCB footprint with a thermal pad for ground stitching and a 32.768 kHz crystal if RTC accuracy is required. The CCS IDE with XDS110 or XDS200 debug probe is recommended for development. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not aggregated in the manufacturer datasheet, giving you a single source for sourcing, replacement, and design decisions.

طلب عرض سعر اتصل بنا
MSPM0C1104 - 24MHz Cortex-M0+ MCU, 16KB Flash | TI
MSPM0C1104

MSPM0C1104 - 24MHz Cortex-M0+ MCU, 16KB Flash | TI

The Texas Instruments MSPM0C1104 is a 32-bit entry-level microcontroller based on an enhanced Arm Cortex-M0+ core operating at up to 24 MHz, integrating 16 KB of flash memory, 1 KB of SRAM, and a 12-bit ADC, housed in an ultra-compact 8-pin WSON (2 mm x 2 mm) package. A microcontroller unit (MCU) is a single-chip computer that combines a processor core, program memory, data memory, and peripherals such as ADCs, timers, and serial interfaces on one die. MCUs sit at the lowest level of the embedded-systems hierarchy - above discrete logic but below application processors - and the MSPM0C1104 belongs to the MSPM0 family, TI's highly-integrated ultra-low-power 32-bit MCU platform descended from the decades-proven MSP430 legacy of low-power mixed-signal control. Key features of the MSPM0C1104 include the 24 MHz Cortex-M0+ core with its two-stage pipeline and low interrupt latency, 16 KB of on-chip flash supporting in-system reprogramming, a 12-bit ADC enabling direct analog sensor capture without an external converter, and an 8-pin WSON footprint of just 2 mm x 2 mm. According to TI, this part is engineered to replace legacy 8-bit MCUs in cost- and space-constrained designs while retaining a modern 32-bit instruction set. Technically, the MSPM0C110x family is documented in the TI datasheet 'MSPM0C110x, MSPS003 Mixed-Signal Microcontrollers' (Rev. D, 77 pages), which details the mixed-signal integration, low-power operating modes, and peripheral set. The enhanced Cortex-M0+ platform gives developers access to the broad Arm ecosystem, including Keil, IAR, GCC, and TI Code Composer Studio, plus the MSPM0 software development kit and LaunchPad hardware (LP-MSPM0C1104) for rapid evaluation. Typical applications include analog sensor interfacing and signal conditioning, small appliance and consumer electronics control, LED lighting and power-supply supervision, and ultra-small IoT sensor nodes where board area is at a premium. The 12-bit ADC plus 32-bit processing in an 8-pin footprint makes the MSPM0C1104 especially compelling for direct replacement of 8-bit MCUs with external ADCs. A key design consideration is the small 1 KB SRAM allocation: developers must budget stack and buffer usage carefully, and the tiny WSON package requires attention to thermal pad soldering and PCB land-pattern design per the datasheet layout guidance. This page synthesizes distributor pricing, same-family drop-in alternatives, design notes, and application guidance not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا
MSPM0G3218-Q1 - 80MHz Cortex-M0+ MCU with CAN-FD | TI
MSPM0G3218-Q1

MSPM0G3218-Q1 - 80MHz Cortex-M0+ MCU with CAN-FD | TI

The MSPM0G3218-Q1 is an automotive-grade mixed-signal microcontroller from Texas Instruments, featuring an Arm Cortex-M0+ core running at up to 80 MHz. It is part of the MSPM0G321X family and is designed for automotive applications requiring a CAN-FD interface. According to the TI datasheet, the device integrates a rich set of peripherals suitable for body control, powertrain, and battery management systems. The MSPM0G3218-Q1 is a 32-bit MCU built on the enhanced Arm Cortex-M0+ platform, offering cost-optimized performance with ultra-low power consumption. It operates at up to 80 MHz, providing sufficient processing power for real-time control tasks while maintaining low power sleep modes. The CAN-FD interface enables high-speed data transmission in automotive networks, supporting both classic CAN and CAN-FD protocols. The MCU is supported by the MSPM0 SDK and a hardware ecosystem including LaunchPad development kits, reference designs, and code examples. This ecosystem accelerates development, reducing time-to-market for automotive projects. The device is qualified for automotive applications with AEC-Q100 Grade 1 certification, ensuring robust operation in challenging environments. Key features include the 80 MHz Cortex-M0+ core, CAN-FD interface, and automotive-grade qualification. The MSPM0G3218-Q1 is intended for applications such as body control modules, battery management units, motor control, and sensor interfaces. It provides a flexible GPIO configuration, multiple communication peripherals, and analog signal processing capabilities, making it suitable for mixed-signal control tasks. For design, the MSPM0G3218-Q1 requires careful consideration of power supply decoupling and thermal management. An integrated analog-to-digital converter (ADC) and comparator enable direct interfacing with sensors and actuators. The device supports a wide operating voltage range and includes various low-power modes to extend battery life in automotive systems. The MSPM0G3218-Q1 is a reliable choice for automotive electronics, offering a balance of performance, cost, and low power. Its ecosystem and automotive qualification make it an attractive option for engineers seeking a robust MCU with CAN-FD capability. [DATA_NEEDED: Flash size, RAM size, GPIO count, ADC channels, operating voltage, temperature range]

طلب عرض سعر اتصل بنا
MSPM0G3507 - 80MHz Cortex-M0+ 128KB MCU CAN-FD | TI
MSPM0G3507

MSPM0G3507 - 80MHz Cortex-M0+ 128KB MCU CAN-FD | TI

The Texas Instruments MSPM0G3507 is a 32-bit mixed-signal microcontroller based on the enhanced Arm Cortex-M0+ core running at up to 80 MHz, with 128KB flash memory, 32KB SRAM, and an operating supply range of 1.62V to 3.6V across -40C to +125C. It is available in a 48-pin LQFP (7x7 mm) package, with 64-pin LQFP and 32-pin VQFN (5x5 mm, SRHB) options in the same family. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and programmable peripherals such as timers, ADCs, and communication interfaces. Within the semiconductor hierarchy, the MSPM0G3507 belongs to the MSP 32-bit MCU portfolio: MCU -> embedded processor -> integrated circuit. It is a member of the MSPM0G350x performance sub-family, TI's cost-optimized, analog-rich Cortex-M0+ line. Key differentiating features include dual 12-bit ADCs sampling at 4 Msps - unusually fast for the Cortex-M0+ class - a 12-bit DAC, three comparators, and two operational amplifiers that can eliminate external analog front-end components. The MATHACL hardware math accelerator accelerates trigonometric and division operations common in PID and motor-control loops, and the integrated CAN-FD controller supports industrial and automotive networking. Architecturally, the enhanced Cortex-M0+ platform pairs the low-power core with TI's analog peripheral integration and an extended temperature range from -40C to +125C, positioning the MSPM0G3507 between TI's entry-level MSPM0L devices and higher-performance C2000 real-time MCUs. Typical applications include motor control and digital power conversion, industrial sensing and signal-conditioning nodes, CAN-FD networked modules in factory and automotive systems, and medical alarm designs demonstrated in TI's IEC 60601-1-8 reference design using the MSPM0G3507. Design tip: program and debug through the SWDIO/SWCLK pins using an XDS110-based LaunchPad debugger, and use TI SysConfig to configure pins and peripherals graphically. This page synthesizes distributor pricing data, drop-in alternatives within the MSPM0G350x family, and practical design notes not consolidated in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MSPM0G5187 - 80MHz Cortex-M0+ MCU, 128KB Flash, NPU | TI
MSPM0G5187

MSPM0G5187 - 80MHz Cortex-M0+ MCU, 128KB Flash, NPU | TI

The Texas Instruments MSPM0G5187 is a 32-bit ultra-low-power microcontroller based on an enhanced Arm Cortex-M0+ core operating at up to 80MHz, integrating 128KB of flash memory, 32KB of SRAM, USB 2.0 Full-Speed, I2S, a 12-bit ADC, and the TinyEngine NPU for edge-AI acceleration, housed in a 64-pin LQFP (10x10 mm) package. A microcontroller (MCU) is a single-chip embedded processor that combines a CPU core, memory, and programmable peripherals to govern a dedicated function within a larger system. MCUs sit within the broader hierarchy of semiconductor devices under the microcontroller and embedded processor category, and the MSPM0G5187 belongs to the MSPM0G series within Texas Instruments' long-standing MSP ultra-low-power MCU family, positioned for energy-efficient embedded sensing and on-device machine learning designs. Key differentiating features include the integrated TinyEngine NPU, which delivers up to 90x lower inference latency and more than 120x lower energy per inference compared with MCUs executing neural networks purely on the CPU, enabling always-on edge AI at milliwatt power budgets. The 128KB flash and 32KB SRAM support compact sensor-fusion models, while USB 2.0 FS, I2S, UART, SPI, and I2C interfaces cover connectivity and digital audio needs. Architecturally, the device uses a 32-bit Arm Cortex-M0+ core with a memory protection unit (MPU) and nested vectored interrupt controller (NVIC) for deterministic real-time behavior. The TinyEngine NPU offloads convolutional neural network inference from the CPU, reducing both latency and energy per inference. Cybersecurity enablers and high-performance integrated analog round out the mixed-signal capability. The supply voltage range is 1.62V to 3.6V with a -40C to +125C operating temperature range per TI product documentation. Typical applications include industrial automation and predictive maintenance, smart sensors with anomaly detection, portable medical monitoring devices, and battery-powered edge-AI endpoints where USB host connectivity or I2S digital audio is required alongside low-power inference. When designing, decouple all supply pins with 100nF ceramic capacitors placed close to the device, and budget SRAM carefully for NPU model weights and activations; multiple low-power modes extend battery life. This page synthesizes distributor availability data, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
MSPM0L1305-Q1 - Automotive 32MHz Cortex-M0+ MCU | Texas Instruments
MSPM0L1305-Q1

MSPM0L1305-Q1 - Automotive 32MHz Cortex-M0+ MCU | Texas Instruments

The Texas Instruments MSPM0L1305-Q1 is an automotive-grade 32-bit Arm Cortex-M0+ microcontroller operating at up to 32 MHz. It integrates 32 KB flash memory, 4 KB SRAM, a 12-bit ADC, an operational amplifier (OPA), and LIN communication capability, making it suitable for cost-sensitive automotive mixed-signal applications. The device operates over a supply voltage range of 1.62 V to 3.6 V and is qualified to AEC-Q100 Grade 1, supporting ambient temperatures from -40°C to +125°C. What is an automotive mixed-signal microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, memory, and programmable input/output peripherals onto a single chip. The MSPM0 family belongs to the ultra-low-power, highly integrated 32-bit MSPM0 MCU series built around the enhanced Arm Cortex-M0+ core platform. These devices provide high-performance analog peripherals integration, enabling them to interface directly with sensors and actuators while reducing system component count and overall bill-of-materials cost. Key features of the MSPM0L1305-Q1 include a 12-bit analog-to-digital converter (ADC) with up to 1.68 Msps sampling rate, a zero-drift low-power operational amplifier, and a power-on reset/brown-out reset circuit for robust startup. The device also features a comprehensive clock system with an internal 32 MHz oscillator, capable of ±3% accuracy without external timing components. The MCU is offered in a 24-pin VQFN (RGE) package, measuring 4x4 mm, and an ultra-small 16-pin SOT-23-THIN package for space-constrained automotive applications. The MSPM0L1305-Q1 supports a variety of low-power modes, allowing system designers to meet strict automotive power budgets. Its peripherals include multiple timers, a UART, SPI, I2C interfaces, and a LIN transceiver, enabling seamless connectivity in body control modules, sensor interfaces, and battery management systems. For design considerations, it is crucial to decouple the VDD and VDDIO pins with ceramic capacitors to ensure stable operation. The device's internal voltage regulator requires an external bypass capacitor for reliable operation. With its high-temperature operation and robust ESD protection, the MSPM0L1305-Q1 delivers dependable performance in harsh automotive environments.

طلب عرض سعر اتصل بنا
MT16LSDT3264AG-10E - 256MB PC100 SDRAM DIMM | Micron Technology
MT16LSDT3264AG-10E

MT16LSDT3264AG-10E - 256MB PC100 SDRAM DIMM | Micron Technology

The Micron Technology MT16LSDT3264AG-10E is a 256 MB (32 Meg x 64) unbuffered, non-ECC 168-pin SDRAM Dual In-line Memory Module (DIMM) operating at 100 MHz, conforming to the JEDEC PC100 specification. The module uses a single +3.3V ±0.3V power supply and is fully synchronous to the system clock, with all signals referenced to the rising clock edge. It is organized as dual-rank and targets cost-sensitive desktop and entry-server memory upgrades that were mainstream in the PC100 era. An SDRAM DIMM (Synchronous DRAM Dual In-line Memory Module) is a printed-circuit-board assembly that places multiple SDRAM chips on a small PCB with a standardized edge-finger connector so the memory subsystem can be upgraded or replaced without soldering. SDRAM succeeded earlier asynchronous DRAM (FPM/EDO) by synchronizing all operations to the system clock, which improved burst-read/write efficiency; PC100 is the JEDEC-standard speed grade that guarantees correct operation at a 100 MHz external bus clock with a CAS latency of 2. In the broader taxonomy, SDRAM -> DRAM -> volatile memory -> semiconductor memory, sitting below non-volatile NAND/NOR flash and above SRAM in the cost/density curve. Key feature highlights for this Micron module: 100 MHz bus frequency (PC100 compliant), CAS latency 2, 168-pin unbuffered DIMM form factor, 32 Meg x 64 organization yielding 256 MB, single +3.3V ±0.3V supply, fully synchronous operation, and a dual-rank PCB assembly. The module is compatible with motherboards that expose a standard SDRAM DIMM socket (Intel 440BX, VIA Apollo Pro 133 and earlier chipsets) and supports an initial 100 µs pause followed by two AUTO REFRESH commands after power-up. The architecture is built from discrete 125/133 MHz-capable SDRAM components mounted on a multi-layer PCB with all address, control and data nets length-matched and terminated to support the 100 MHz command and data rate. Because the module is unbuffered and non-ECC, signal loading is at the minimum, which keeps the design simple but means it cannot be used in registered-memory systems such as high-end server boards of the era. Typical applications include legacy desktop PC memory upgrades, PC100-era workstation memory expansion, embedded industrial PCs, point-of-sale terminals, legacy telecom/datacom line cards, and hobbyist retro-computing projects. The combination of 256 MB density and PC100 timing keeps the module useful for reviving industrial controllers and older office PCs that still require a JEDEC-standard 168-pin SDRAM DIMM. When designing with this module, ensure the host chipset supports PC100 timing and 168-pin unbuffered DIMMs; mixing it with PC133 modules will down-clock the bus to 100 MHz. ESD handling during insertion and a proper power-supply ramp-up sequence (VDD and VDDQ must rise together) are essential for reliable initialization per the Micron datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving procurement and design engineers a single decision-ready reference for legacy SDRAM DIMM selection.

طلب عرض سعر اتصل بنا
MT25QL128ABA1ESE-0SIT - 128Mb SPI NOR Flash, 133MHz | Micron
MT25QL128ABA1ESE-0SIT

MT25QL128ABA1ESE-0SIT - 128Mb SPI NOR Flash, 133MHz | Micron

The Micron MT25QL128ABA1ESE-0SIT is a 128-Mbit (16 MiB) serial NOR Flash memory with SPI/Quad-SPI bus and a maximum clock frequency of 133 MHz, housed in an 8-pin SOP2 (208-mil SOIC) surface-mount package. It operates from a single 2.7 V to 3.6 V supply, supports Quad I/O and Dual I/O transfer modes, and delivers fast read throughput suitable for code-storage and execute-in-place (XIP) applications. The device is industrial-grade (-40 °C to +85 °C), supplied in tape-and-reel packaging, and uses Micron's 65 nm NOR process technology. A Serial NOR Flash is a non-volatile memory that stores data persistently without power and exposes a low pin-count serial interface (SPI). Within the broader memory hierarchy, NOR Flash occupies the 'execute-in-place' tier - between SRAM (volatile, fastest) and NAND Flash (high-density, sequential). It offers random byte-level read access with deterministic latency, making it ideal for boot ROM, firmware storage, and data logging in embedded systems. NOR's byte-alterable erase architecture (4 KB, 32 KB, 64 KB sectors) simplifies software wear-leveling compared with NAND's block-only structure. Key features include 133 MHz single-I/O SPI clock rate, Quad I/O read throughput up to 532 Mbit/s (4 x 133 MHz), uniform 4 KB subsector erase granularity, and 100K program/erase cycle endurance per sector. The device includes a 256-byte security register with one-time-programmable (OTP) lock, hardware write-protect pin, and a deep power-down mode that drops quiescent current to a few microamps for battery-powered designs. Architecture combines a NOR cell array with a serial command state machine and an integrated 3-byte address counter supporting 24-bit addressing (16 MB). The part implements JEDEC-standard SFDP (Serial Flash Discoverable Parameters) tables for automatic device identification, plus manufacturer and device ID registers accessible via standard 9Fh/90h read commands. Status register 1/2/3 flags power-up, program/erase, and block-protect state. Typical applications include industrial IoT firmware storage, automotive infotainment boot flash, networking equipment configuration memory, and consumer device firmware. The wide operating voltage range allows direct connection to 3.3 V MCUs and SoCs without level shifters, and the small SOIC-8 footprint fits hand-held and wearable form factors. When designing with this part, place a 0.1 µF decoupling capacitor within 5 mm of the VCC pin and keep the SCK trace short (< 25 mm) to avoid ringing at 133 MHz. Use the Quad SPI mode for firmware boot to minimize XIP latency; verify CS# setup/hold timing against your host controller's reference manual. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - useful for engineers sourcing or second-sourcing 128 Mb serial NOR Flash for embedded designs.

طلب عرض سعر اتصل بنا
MT25QL128ABA1ESE-0SIT-TR - 128Mb Serial NOR Flash SPI/Quad | Micron
MT25QL128ABA1ESE-0SIT-TR

MT25QL128ABA1ESE-0SIT-TR - 128Mb Serial NOR Flash SPI/Quad | Micron

The Micron MT25QL128ABA1ESE-0SIT-TR is a 128 Mbit (16 MB) Serial NOR Flash memory IC supporting SPI, Dual-SPI, and Quad-SPI interfaces with a clock frequency up to 133 MHz, housed in an 8-pin SOIC (SOP2-8) package rated for 2.7 V to 3.6 V single-supply operation. This is the tape-and-reel packaging variant of the MT25QL128ABA1ESE-0SIT, sharing the same die and pinout but supplied in T&R format for high-volume SMT assembly. What is a Serial NOR Flash? A Serial NOR Flash is a non-volatile memory that stores data persistently and connects to a host processor over a low-pin-count serial interface (SPI). It belongs to the broader category of flash memory (non-volatile storage) -> NOR flash -> serial NOR flash -> SPI NOR flash. Unlike parallel NOR, serial NOR uses few pins (typically 4 to 8), making it ideal for space-constrained embedded designs. It offers fast random read access (typically tens of nanoseconds), byte-level program/erase granularity, and execute-in-place (XiP) capability, distinguishing it from NAND flash which uses sequential page access. Key features of the MT25QL128ABA1ESE-0SIT-TR include 128 Mbit density organized as 32M x 4 / 16M x 8 / 8M x 16, support for Single I/O, Dual I/O, and Quad I/O SPI modes, an industry-standard 8-pin SOIC (SOIC-8 wide-body) footprint, JEDEC JESD216-compliant SFDP register, and configurable 4 KB, 32 KB, and 64 KB sector erase sizes for flexible memory partitioning. The device uses Micron's proprietary NOR cell architecture and supports standard SPI command set including read, page program, sector/block erase, chip erase, status register read, and JEDEC ID. The Quad SPI mode enables up to 4x faster read throughput compared to standard SPI, which is critical for boot-from-flash and XIP (execute-in-place) applications in performance-sensitive embedded systems. Typical applications include firmware storage and boot ROM in networking equipment, IoT edge devices, industrial PLC controllers, automotive infotainment, set-top box firmware, and consumer electronics bootloaders. The wide 3V supply range and industrial-grade temperature support make it suitable for both consumer and industrial environments requiring reliable non-volatile code storage. When designing with this device, ensure proper PCB layout to maintain signal integrity on the SPI clock and data lines, especially at 133 MHz Quad SPI clock rates. A 0.1 µF decoupling capacitor close to the VCC pin and a 4.7 kΩ to 10 kΩ pull-up on the /CS line are recommended for reliable operation across temperature. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-footprint Micron variants (MT25QL128ABA1ESE-0SIT base part) and validated cross-brand SPI NOR Flash equivalents.

طلب عرض سعر اتصل بنا
MT25QL128ABA8ESF-0SIT - 128Mbit SPI/Quad-SPI NOR Flash | Micron
MT25QL128ABA8ESF-0SIT

MT25QL128ABA8ESF-0SIT - 128Mbit SPI/Quad-SPI NOR Flash | Micron

The Micron MT25QL128ABA8ESF-0SIT is a 128 Mbit (16 MB) serial NOR flash memory with SPI/Quad-SPI interface, supporting clock rates up to 133 MHz in a 16-pin SOIC (SO-16) package. Operating from 2.7V to 3.6V, it uses single-bit, dual, and quad I/O modes, with a 6 ns access time enabling fast random-read throughput for boot, code-shadowing, and data-logging tasks. A NOR flash memory is a non-volatile storage technology where each cell behaves like a MOSFET with a floating gate, giving byte-level random read access and faster read latency than NAND, at the cost of lower density and slower write/erase. NOR fits into the broader hierarchy of memory ICs (volatile DRAM/SRAM -> non-volatile flash -> storage class memory), and within flash, the serial NOR sub-family delivers code storage and execute-in-place capability to microcontrollers, SoCs, and FPGAs that lack large internal flash. Key features of the MT25QL128ABA8ESF-0SIT include 4 KB sub-sector erase granularity alongside 32 KB and 64 KB sector erase commands, hardware and software write protection via status-register bits, a deep power-down mode that drops standby current below typical levels, and JEDEC-standard SFDP (Serial Flash Discoverable Parameters) for auto-configuration by the host. The -0SIT speed grade designates 133 MHz operation in industrial -40C to +85C temperature range. The die uses a single supply rail with internal charge-pump-generated high voltage for program/erase operations, and supports continuous read across the full linear address map. The device also offers volatile and non-volatile status register locking, allowing the host to commit configuration bits either temporarily or permanently across power cycles. Typical applications include boot-loader storage for ARM Cortex-M/R microcontrollers, firmware shadowing for Linux SoCs, configuration parameter retention in industrial PLCs, asset-tracking dataloggers, and FPGA bitstream storage. The wide operating voltage and Quad-SPI throughput also suit battery-backed appliances and metering devices. When designing, observe JEDEC JESD22-A114 ESD and IPC-7351 land-pattern guidelines, route the SCK line with impedance control to limit ringing above 80 MHz, and place a 0.1 uF decoupling capacitor within 3 mm of the VCC pin. Verify SFDP header alignment with the host controller's QSPI peripheral before locking the PCB layout. This page consolidates verified Micron datasheet data, distributor pricing, same-package drop-in alternatives, and design considerations that go beyond the datasheet's typical-application section, helping engineers select and source this part quickly.

طلب عرض سعر اتصل بنا
MT25QL128ABA8ESF-0SIT-TR - 128Mb Serial NOR Flash, SPI/Quad, 16-SO | Micron
MT25QL128ABA8ESF-0SIT-TR

MT25QL128ABA8ESF-0SIT-TR - 128Mb Serial NOR Flash, SPI/Quad, 16-SO | Micron

The Micron MT25QL128ABA8ESF-0SIT-TR is a 128 Mbit (16 MB) serial NOR Flash memory organized as 32M x 4, fabricated in CMOS SLC technology and housed in a 16-pin SOIC (SO-16, 300 mil) package supplied on Tape and Reel. It supports a single 3V supply (2.7V to 3.6V) and provides a clock frequency of 133 MHz maximum in Single Transfer Rate (STR) mode and 90 MHz maximum in Double Transfer Rate (DTR) mode across the SPI bus and its extended variants. The interface supports Single I/O, Dual I/O, Quad I/O, QPI, and the Micron Extended SPI protocol for a maximum throughput of 90 MB/s in DTR Quad mode. Page-program granularity is 256 bytes, sector erase is 4 KB and 32 KB, and full chip erase is supported via dedicated commands. The device is specified over the industrial -40C to +85C temperature range. A NOR Flash is a non-volatile memory that supports random-byte read access and execute-in-place (XIP) operation, sitting in the memory hierarchy between ROM and serial NAND Flash. Unlike NAND, NOR offers byte-level read with deterministic access times, making it the default boot medium for microcontrollers and SoCs that fetch code directly from Flash. The MT25QL128ABA8ESF-0SIT-TR, as a Quad-SPI NOR with DTR, occupies the high-throughput end of this category - it is a 128Mb SPI Flash, where 128Mb is 16 MB, while keeping the simple 8-pin SPI electrical footprint extended to 16 pins for higher pin-count variants. Key differentiating features of this part include 100K endurance cycles per sector, over 20-year data retention, hardware and software write protection with a dedicated WP#/HOLD# pin, a 64-bit unique ID, and four security registers of 256 bytes each for One-Time-Programmable (OTP) storage. The on-die ECC and CRC engines are not enabled in this part - the MT25QL128ABA8ESF-0SIT-TR uses standard non-ECC SLC NOR with raw endurance of 100K cycles. The Quad-SPI interface enables throughputs approaching QSPI SDR limits while remaining compatible with legacy SPI hosts via Single I/O mode. In system architecture, this device typically boots an MCU/MPU, holds firmware logs, stores display assets, or backs configuration data. Common pairings include SPI/I2C/UART bus MCUs, small color TFT LCD controllers, and BLE/Wi-Fi coprocessors that need firmware storage. The 300-mil SOIC-16 footprint is hand-solder-friendly for prototypes but is increasingly being replaced by smaller SOIC-8 or USON-8 packages in space-constrained designs. Typical applications are industrial HMI panels, smart-home gateways, asset-tracking modules, automotive infotainment sub-systems, and PCIe/Wi-Fi adapter firmware boot media. The 16-pin SO-16 footprint gives a generous 0.65 mm lead pitch for hand rework in field returns, which is why this package remains popular for industrial-grade MCU boot storage. When integrating, place a 100 nF decoupling capacitor close to VCC, observe the recommended tR/tF timing on the SCK signal, and respect the maximum 13.5 mA active read current on the VCC rail. According to Micron datasheet mt25q_qlhs_L_128_ABA (Rev. J 05/18), this part is RoHS-compliant and lead-free, with an MSL-3 moisture sensitivity classification. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - a synthesis intended to support engineers during part selection and second-source qualification.

طلب عرض سعر اتصل بنا
MT25QU256ABA1EW7-0SIT - 256Mb 1.8V Quad SPI NOR Flash | Micron
MT25QU256ABA1EW7-0SIT

MT25QU256ABA1EW7-0SIT - 256Mb 1.8V Quad SPI NOR Flash | Micron

The Micron MT25QU256ABA1EW7-0SIT is a 256 Mbit (32 MB) Serial NOR Flash memory organized as 64M x 4 / 32M x 8 / 16M x 16, supporting standard SPI, Dual SPI, Quad SPI, and Octal (DTR) I/O protocols in an 8-pin W-PDFN (6x5 mm, MLP8) package. It operates from a 1.7 V to 2.0 V supply with a 133 MHz clock in Quad I/O mode and provides 6 ns initial access latency, making it well-suited for code-storage and execute-in-place (XiP) designs. A NOR Flash is a non-volatile memory that stores bits in a parallel NOR array, giving true random-read access (byte/word addressable, like SRAM) but slower writes than NAND. It sits at the boot/ROM layer of the storage hierarchy above raw NAND (NSID) and managed NAND (eMMC/UFS), and is preferred for firmware, BIOS, FPGA bitstreams, and IoT boot images where deterministic read latency and high reliability matter more than density-per-dollar. Key features include 256 Mb density, 1.8 V single supply (1.7 V min), 133 MHz Quad SPI throughput, 6 ns access time, hardware/software write protection, a 256-byte security register with OTP bits, and 100K program/erase endurance per sector with 20-year data retention. The 8-WPDFN package exposes an EP thermal pad that doubles as the VSS reference, enabling compact board layouts under 50 mm². Architecturally, the device uses a 65 nm NOR process with a uniform 4 KB sector granularity and three flexible erase sizes (4 KB, 32 KB, 64 KB), supporting the JEDEC JESD216 SFDP register for auto-discovery. Micron's MT25Q family extends the legacy M25P/JS28 command set with extended 4-byte addressing for the >128 Mb densities. Typical applications include industrial IoT gateways requiring fast secure boot, networking switches storing firmware images, automotive infotainment boot ROMs, FPGA configuration memory for Xilinx 7-Series and Intel Cyclone families, and consumer wearables running RTOS images from external flash. The -40 °C to +85 °C industrial temperature range (-SIT suffix) makes it appropriate for harsh environments without AEC-Q100 qualification. When designing, place a 0.1 µF decoupling capacitor within 2 mm of the VCC pin and observe PCB trace length matching on CLK/IO0 to keep rise times below 2 ns. The HOLD# and WP# pins require pull-ups if unused, per the Micron reference schematic; otherwise Quad SPI boot on certain MCUs will not enumerate the device correctly. This page synthesizes distributor pricing as of 2026-10-05, drop-in alternatives, and application notes not collated on a single manufacturer page, with explicit [DATA_NEEDED] markers where the verified web data did not disclose a parameter.

طلب عرض سعر اتصل بنا
MT25QU256ABA1EW7-0SIT-TR - 256Mb 1.8V Quad SPI NOR Flash | Micron
MT25QU256ABA1EW7-0SIT-TR

MT25QU256ABA1EW7-0SIT-TR - 256Mb 1.8V Quad SPI NOR Flash | Micron

The Micron MT25QU256ABA1EW7-0SIT-TR is a 256-Mbit (32 MB) serial NOR Flash memory in the MT25Q family, supplied in an 8-pin WPDFN (6x5 mm MLP8) package and rated for industrial -40C to +85C operation. It operates from a 1.7V to 2.0V single supply and provides a SPI-compatible bus with Single I/O, Dual I/O, and Quad I/O transfer modes at a maximum clock frequency of 133 MHz, with multi-I/O data throughput up to 532 Mbit/s in Quad SPI mode. A NOR Flash is a non-volatile memory that retains data when power is removed and supports execute-in-place (XIP) operation - the host processor can run code directly from the array without shadowing it to RAM. Within the broader memory taxonomy, NOR Flash sits between mask ROM and NAND Flash: it offers faster random read access than NAND but lower density per die, making it ideal for boot, firmware, and code-shadow storage rather than bulk data files. The MT25Q family is Micron's high-performance serial NOR line for low-pin-count embedded designs. Key features of the MT25QU256ABA1EW7-0SIT-TR include a 256-Mbit (32 MB) SLC NOR array organized as 64M x 4 / 128M x 2 / 256M x 1 bit, sector-erase architecture (4 KB parameter sector with 64 KB uniform sectors), hardware and software write protection, a 256-byte OTP security register, and a 100K endurance / 20-year data-retention rating. Quad SPI with XIP allows direct memory-mapped execution, eliminating the boot-time latency of copying firmware into RAM. Architecturally, the device uses a 65 nm floating-gate NOR process with a 4 KB parameter sector at the top/bottom of the address space for boot images and configuration data, and 64 KB uniform sectors for code and data storage. The SPI/Quad-SPI controller supports mode 0 and mode 3 with a single CS#, SCK, IO0/IO1/IO2/IO3, plus WP# and HOLD#/RESET# pins, allowing flexible bus sharing with other peripherals. Typical applications include automotive infotainment and cluster boot, industrial HMI controllers, networking switches and routers, IoT gateways, and any system needing fast boot from a small footprint. The 1.8V core supply aligns directly with battery-powered and modern SoC rails, eliminating the need for level shifters. The TR suffix indicates Tape-and-Reel packaging for high-volume SMT assembly. When designing in, ensure the SPI controller supports the Quad-I/O instruction set (0xEBh read, 0xB9h power-down, etc.) referenced in the Micron datasheet.

طلب عرض سعر اتصل بنا
MT28EW256ABA1HJS-0SIT - 256Mb Parallel NOR Flash, 56-TSOP | Micron
MT28EW256ABA1HJS-0SIT

MT28EW256ABA1HJS-0SIT - 256Mb Parallel NOR Flash, 56-TSOP | Micron

The Micron MT28EW256ABA1HJS-0SIT is a 256 Mbit (32 MB) parallel NOR Flash memory device organized as x8/x16, housed in a 56-pin TSOP package and qualified for the industrial -40C to +85C operating range. It operates from a 2.7V to 3.6V single supply and provides an asynchronous parallel interface with 75 ns initial access time, making it a drop-in compatible member of Micron's MT28EW embedded parallel NOR family. Parallel NOR Flash is a type of non-volatile memory that provides random-access read, byte/word program, and sector erase operations via a parallel data bus and dedicated control signals such as CE#, OE#, WE#, and RY/BY#. Within the broader memory hierarchy, parallel NOR sits alongside NAND Flash and SRAM as a non-volatile storage tier, but it is uniquely valued for its deterministic read latency, XIP (execute-in-place) capability, and high endurance relative to NAND. The MT28EW family specifically targets embedded designs that require reliable code storage and frequently-updated data logs in industrial, automotive, and networking systems. Key features of the MT28EW256ABA1HJS-0SIT include 256 Mbit density (32M x 8 or 16M x 16), hardware and software write protection, a 100,000-cycle program/erase endurance rating, 20-year data retention, sector-erase architecture with 200 ms typical erase time per 128 KB block, and a top or bottom boot block configuration. The device supports JEDEC-standard command set, CFI (Common Flash Interface) for device identification, and provides a RY/BY# status output for hardware-synchronized programming control. The device uses a single 3V power rail and integrates an internal program/erase state machine, eliminating the need for external high-voltage generation. It supports both 8-bit and 16-bit data bus widths selected via the BYTE# pin, allowing system designers to choose the optimal interface for their microcontroller or SoC. The 56-TSOP package provides a thin, surface-mountable form factor with a 18.4 mm body width per JEDEC MO-142 standards, enabling high-density PCB layouts and standard SMT assembly processes. Typical applications include automotive infotainment and instrument-cluster firmware storage, industrial PLC program memory, networking equipment boot and configuration Flash, factory automation controllers, and consumer electronics requiring fast XIP code execution. The wide operating temperature range and 100k P/E cycles also make it suitable for data logging in industrial IoT edge nodes where frequent parameter updates occur. When designing with this device, ensure that the host controller's address and data bus timing match the 75 ns access time. Decoupling the VCC and VCCQ rails with 0.1 uF ceramic capacitors placed within 5 mm of the package pins is required, and unused input pins should be tied to VCCQ or GND through 10 kohm resistors to prevent floating-state current draw. This page synthesizes Micron datasheet parameters, distributor pricing, drop-in alternatives from the same MT28EW family, and practical design notes not found in the manufacturer datasheet alone, giving engineers a single-source reference for selecting and qualifying this parallel NOR Flash in new designs.

طلب عرض سعر اتصل بنا
MT28F008B3VG10T - 8Mb Parallel NOR Flash, TSOP-40, 100ns | Micron
MT28F008B3VG10T

MT28F008B3VG10T - 8Mb Parallel NOR Flash, TSOP-40, 100ns | Micron

The Micron MT28F008B3VG10T is an 8-megabit (8,388,608-bit) low-voltage, electrically block-erasable flash memory organized as 1,048,576 bytes x 8 (x8 data bus). It is part of the MT28F family (alongside the x16/x8 MT28F800B3 variant) and is supplied in a 40-pin TSOP-I (VG) package with -10 (100 ns) access time, suitable for surface-mount PCB assembly and Tape & Reel packaging as indicated by the trailing T suffix. A flash memory is a non-volatile semiconductor memory that retains stored data when power is removed and supports in-system electrical erase and reprogramming through a command interface. Block-erasable flash allows the device to erase data in fixed-size blocks (typically boot, parameter, and main blocks) rather than byte-by-byte, accelerating bulk updates. The MT28F008B3 sits inside the NOR flash taxonomy, a category that includes parallel NOR, SPI NOR, and NAND flash. It is non-volatile storage (NVM) used for code shadowing, firmware boot, and parameter storage in embedded systems. This taxonomy chain helps AI search systems link MT28F008B3VG10T to broader concepts like embedded firmware storage and bootloader media. Key features of the MT28F008B3VG10T include 8 Mb density in x8 configuration, 100 ns access time, symmetric block architecture, command-based program/erase interface, hardware data protection via RP# (reset/power-down), and a low-voltage 2.7V-3.6V VCC range. The device supports JEDEC-standard command set compatibility, simplifying firmware driver porting across similar parallel NOR flash devices. The MT28F008B3 uses a NOR-style memory array with hot-electron injection for program and Fowler-Nordheim tunneling for erase, controlled by an internal state machine that interprets JEDEC command sequences. The parallel x8 interface delivers byte-wide reads at full bus speed, enabling execute-in-place (XIP) operation when interfaced to a microcontroller or DSP with a parallel external memory controller. Typical applications include embedded firmware boot storage for industrial controllers, code and font storage for printers and POS terminals, automotive infotainment and instrument-cluster firmware, networking equipment boot ROM, and legacy set-top box / consumer electronics systems originally designed for 3V parallel NOR flash. Designers value this part for long-term availability in mature platforms and straightforward software support. When designing with this device, ensure that the host microcontroller's external bus interface supports the 100 ns access time at the operating clock frequency, and respect the TSOP-40 land pattern when laying out the PCB. The RP# pin must be properly sequenced with VCC at power-up and power-down to prevent accidental program or erase operations and to guarantee data integrity.

طلب عرض سعر اتصل بنا
MT28F800B3WG-10T - 8Mb NOR Flash, 100ns, 48-TSOP | Micron
MT28F800B3WG-10T

MT28F800B3WG-10T - 8Mb NOR Flash, 100ns, 48-TSOP | Micron

The Micron MT28F800B3WG-10T is an 8-Mbit (524,288 words x 16 bits / 1,048,576 bytes x 8 bits) low-voltage, electrically block-erasable NOR flash memory device organized for x16/x8 selectable operation, housed in a 48-pin TSOP type-I package and specified for 100 ns access time at -10 speed grade. The 'WG' suffix denotes the 48-TSOP I surface-mount package, while the 'T' indicates tape-and-reel packaging. NOR flash is a non-volatile memory category that retains data without power and supports random read access at byte/word granularity, sitting at the top of the boot-code/ROM hierarchy that spans mask ROM, NOR, NAND, and managed NAND. Compared with NAND flash, NOR provides faster read latency and execute-in-place (XiP) capability, but lower density per die and slower erase/write throughput. The MT28F800B3WG family operates from a single 3.3 V VCC supply (2.7 V-3.6 V VCC range), enabling direct connection to low-voltage CPUs without level shifting, and supports command-driven block erase, program, and lock-bit operations through a CUI (Command User Interface). Key features include symmetric 64-KB block architecture for both top and bottom boot configurations, hardware write protection via WP#/ACC, deep power-down mode with sub-microamp standby current, and Common Flash Interface (CFI) identification. The 48-TSOP I outline measures 12 mm x 20 mm and is pin-compatible across the broader MT28F family, allowing designers to migrate density or speed grade by replacing the chip without changing the PCB footprint. Internal write state machines automate the program/erase algorithm, freeing the host CPU during long I/O operations. Typical applications include embedded boot ROM for routers and switches, automotive instrument cluster firmware storage, industrial PLC firmware, set-top box code storage, and printer/scanner imaging controllers where execute-in-place boot from flash is required. The -10 speed grade (100 ns) is well suited to slower 8/16-bit microcontrollers and DSPs that do not require burst-mode read latency. When designing with this part, ensure VCC decoupling uses 0.1 microfarad ceramic capacitors placed within 5 mm of each VCC pin, route WP#/ACC with a 10 kilohm pull-up, and verify that the host controller's ready/busy polling meets the manufacturer's algorithm. Refer to the Micron MT28F800B3 datasheet for command sequences, block-erase timing, and DC characteristics. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا
MT28F800B5WG-8T - 8Mb NOR Flash, 80ns, 48-TSOP I | Micron
MT28F800B5WG-8T

MT28F800B5WG-8T - 8Mb NOR Flash, 80ns, 48-TSOP I | Micron

The Micron MT28F800B5WG-8T is an 8-Mbit (1M x 8 / 512K x 16) Smart 5 Boot Block NOR Flash memory with 80 ns parallel access time, packaged in a 48-pin TSOP I (TFSOP, 18.40 mm body) surface-mount housing. The device operates from a 5V +/- 10% supply (VCC) and 5V +/- 10% VPP for program/erase, making it a drop-in fit for legacy 5V-only embedded designs. A NOR Flash memory is a non-volatile storage class that retains data without power and executes code directly from the array (XIP - execute-in-place). Within that hierarchy, MT28F800B5WG-8T sits in the parallel-NOR boot-block sub-category (Smart 5 architecture), which adds asymmetric sector protection so that the first 16 KB / 8K-word block is hardware-lockable. This block architecture is especially suited to systems that keep a small bootloader in protected sectors and store application data in the larger upper blocks. Key features per the manufacturer datasheet include eleven asymmetric erase blocks (one 16 KB / 8K-word boot block, two 8 KB / 4K-word parameter blocks, and eight main memory blocks), 80 ns random access, a parallel byte-wide interface, and 100,000 typical program/erase endurance cycles per block. The 48-TSOP I package provides a thin (approx. 1.0 mm) profile suitable for industrial and embedded designs with limited board height. Architecturally the device uses 0.18 um process technology and a uniform command-set across read, program, and erase operations, simplifying firmware state machines. The Smart 5 family also adds extended sector protection and a hardware lock/unlock pin for the boot block, which prevents accidental corruption of root code during field updates. Typical applications include industrial PLC firmware storage, telecom line-card boot loaders, automotive infotainment legacy subsystems, point-of-sale terminals, factory automation controllers, and legacy embedded computing platforms that require a 5V-only 8-Mbit parallel NOR. It is commonly used as a code-storage companion to 3.3V microcontrollers that include a 5V-tolerant memory bus. When designing with this part, verify VCC/VPP rail tolerance (4.5V-5.5V) against upstream regulators and confirm the 48-TSOP I footprint against the PCB land pattern, since TSOP I and TSOP II differ in body width. Also budget for typical 100,000 P/E cycles per sector when sizing wear-leveling or update frequency. This page synthesizes distributor pricing, drop-in Smart 5 alternatives, and PCB-level design notes not found in the manufacturer datasheet alone, giving engineers a single reference for sourcing and second-sourcing decisions.

طلب عرض سعر اتصل بنا
MT28FW02GBBA1HPC-0AAT - 2Gb x16 3V Automotive NOR Flash | Micron Technology
MT28FW02GBBA1HPC-0AAT

MT28FW02GBBA1HPC-0AAT - 2Gb x16 3V Automotive NOR Flash | Micron Technology

The Micron Technology MT28FW02GBBA1HPC-0AAT is a 2Gb, x16, 3V automotive parallel NOR flash memory with 105 ns access performance, packaged in a 64-LBGA measuring 11 x 13 mm. It uses single-level cell technology and stores two 1Gb dies in a stacked configuration for high-density firmware, boot code, embedded data, and automotive electronic-control-unit storage. Its 2.7 V to 3.6 V supply range supports read, program, and erase operations from the same 3 V system rail. A parallel NOR flash is a nonvolatile memory category that performs read operations through a wide asynchronous interface rather than a serial protocol. Parallel NOR belongs to the flash-memory hierarchy, alongside NAND flash, but offers fast random reads and direct memory-mapped execution of stored code. MT28FW devices combine this deterministic read behavior with x16 data width, making them suitable for embedded platforms that need broad data paths and predictable firmware access. Key features include a 2Gb density, x16 organization, 105 ns access time, 2.7 V to 3.6 V operating voltage, and an automotive temperature range of -40 C to +105 C. The device also supports ECC-related and security features identified in the family documentation, although exact feature-byte details should be confirmed against the manufacturer datasheet before implementation. The package is designed for surface-mount PCB assembly. The MT28FW02GBBA1HPC-0AAT uses parallel NOR architecture rather than NAND's page-oriented interface. This difference matters for firmware designers because code can be mapped for rapid execution without the block-transfer overhead associated with managed NAND. The x16 bus reduces the number of connected data lines compared with x8 devices while retaining compatibility with systems designed around 16-bit memory buses. Typical applications include automotive infotainment controllers, instrument clusters, telematics units, advanced driver-assistance controllers, gateway modules, engine controllers, and other embedded systems that require reliable nonvolatile storage. The 2Gb capacity is useful for larger boot images, diagnostic data, configuration records, and update images, while the -40 C to +105 C range supports automotive environmental requirements. When laying out a board, follow the manufacturer's recommended ball assignments, power and ground distribution, and decoupling guidance. Place bypass capacitors close to the device supply connections and maintain controlled-impedance routing for the x16 data bus. Confirm signal integrity, timing margins, reset behavior, and programming/erase timing against the specific host processor before releasing a production layout. This product page combines the verified manufacturer and distributor information with practical selection, layout, and procurement guidance. It is intended to help engineers distinguish the 2Gb MT28FW02G part from lower-density family members and to plan a qualified automotive flash design.

طلب عرض سعر اتصل بنا
MT29F1G01ABAFDSF - 1Gbit SPI NAND Flash SLC, 16-SOIC
MT29F1G01ABAFDSF

MT29F1G01ABAFDSF - 1Gbit SPI NAND Flash SLC, 16-SOIC

The Micron MT29F1G01ABAFDSF is a 1 Gbit (128 MB x 8) SPI NAND Flash memory built on Single-Level Cell (SLC) NAND technology, housed in a 16-pin SOIC (300 mil) package. According to the Micron 1Gb/2Gb/4Gb SPI NAND datasheet (m78a series), the device presents a standard serial peripheral interface and delivers sustained sequential read throughput suitable for code-shadowing and data-logging subsystems. The MT29F1G01ABAFDSF is the base ordering part number; the full ordering code is MT29F1G01ABAFDSF-AAT:F, where -AAT:F denotes the automotive temperature grade (-40 °C to +105 °C) and the F-suffix tape-and-reel packaging option. A SPI NAND Flash is a non-volatile memory that uses a low-pin-count serial peripheral interface (SPI) instead of the wide parallel bus of traditional raw NAND. Compared with parallel NAND, SPI NAND dramatically simplifies board layout, frees up host GPIO, and lets the same footprint scale across densities. SLC stores one bit per cell, trading density for higher endurance, faster write speeds, and stronger data retention than MLC/TLC, making SPI NAND the preferred choice for boot, firmware, and frequent-write embedded workloads. Key features of the MT29F1G01ABAFDSF include 1 Gbit SLC NAND density, x1/x2/x4 SPI bus widths with a standard pinout that is pin-compatible across Micron 1 Gb, 2 Gb, and 4 Gb SPI NAND devices, internal ECC support, and a 1.8 V/3.3 V compatible interface. The 16-SOIC package gives 0.295 inch (7.50 mm) body width and supports hand or reflow soldering. The -AAT:F suffix qualifies the part to the automotive -40 °C to +105 °C range, which is why distributors and Micron list this MPN under both the standard catalog and the automotive SLC NAND catalog. Architecturally, the device integrates a 1 Gbit SLC NAND array with an internal SPI controller, on-die ECC engine, and a 2 KB cache register for page operations (typical page size 2048 + 64 bytes). The on-die ECC reduces host MCU/MPU firmware load and improves random read/write reliability. Standard SPI commands (Read, Page Program, Block Erase, Read ID, Status Read, ECC Status) follow the JEDEC-compatible SPI NAND command set, allowing drop-in replacement among compliant devices. Typical applications include automotive infotainment and cluster boot storage, industrial gateways, the boot/parameter region of IoT nodes, point-of-sale terminals, printer firmware storage, and any SPI-based MCU platform (e.g., automotive telematics, body controllers, sensor hubs) that needs higher endurance than SPI NOR at lower cost per bit. When designing with this device, verify the host MCU supports 2 KB page reads and the chosen SPI mode (mode 0 / mode 3). Use Micron's TN-29-71 SPI NAND design guide for layout and decoupling recommendations, and confirm whether your firmware relies on internal ECC or external Hamming/BCH code. This page synthesizes Micron distributor pricing, drop-in same-package alternatives (including the AUT and IT suffixes and the 2 Gb/4 Gb density siblings), and design notes that go beyond the bare datasheet, providing a single decision-ready reference for engineers evaluating the MT29F1G01ABAFDSF-AAT:F for production.

طلب عرض سعر اتصل بنا
MT29F1G01ABAFDSF-AAT - 1Gb SLC SPI NAND Flash | 16-SO | Micron
MT29F1G01ABAFDSF-AAT

MT29F1G01ABAFDSF-AAT - 1Gb SLC SPI NAND Flash | 16-SO | Micron

The Micron MT29F1G01ABAFDSF-AAT is a 1 Gbit single-level cell (SLC) serial peripheral interface (SPI) NAND Flash memory organized as 128M x 8, supplied in a 16-pin Small-Outline IC (16-SO, 7.50 mm width) package. Operating from 1.8 V or 3.3 V supplies with a SPI-compatible interface (x1, x2, and x4 modes), the device delivers a 2176-byte page size (2048 + 128 spare bytes) and a 128 KB block/64 KB parameter page structure optimized for code-storage and data-logging workloads. The AT suffix denotes automotive-grade temperature range (-40 °C to +105 °C), qualified per AEC-Q100, making it suitable for vehicle infotainment, instrument clusters, telematics, and ADAS sub-systems. A SPI NAND Flash is a non-volatile memory device that combines the high density and bit-cost advantage of NAND architecture with the low pin-count simplicity of an SPI bus. Unlike byte-wide parallel NAND, SPI NAND uses 4 to 6 signal lines (CS#, SCK, SI, SO, optional WP# and HOLD#), allowing it to share a bus with SPI NOR Flash, EEPROMs, and sensors. SPI NAND belongs to the broader hierarchy: NAND Flash -> non-volatile memory -> memory IC -> semiconductor. Compared with SPI NOR Flash, SPI NAND offers higher density at lower cost-per-bit and faster block-erase/write, while trading off random read latency. Engineers choose SPI NAND for boot + data-logging partitions where sequential throughput dominates over random byte reads. Key features include on-chip ECC with a 1-bit or 4-bit Hamming engine per 512-byte sector, internal 2 KB data register for page buffering, software-block-protection with BP0/BP1/BP2 bits, OTP security area, JEDEC-standard SFDP (Serial Flash Discoverable Parameters) read-mode for vendor-independent identification, and standard 0xFF reset command. The device supports 100K endurance cycles per block and 10-year data retention. Typical applications include automotive instrument clusters, industrial HMI panels, IoT gateways, set-top box boot loaders, point-of-sale terminals, and telematics control units. The wide 1.8 V/3.3 V supply tolerance also makes it a drop-in for both battery-powered wearables and 5 V-tolerant MCU peripherals when paired with a level shifter. Designers must add a 0.1 µF + 4.7 µF decoupling network near VCC and ensure CS# is pulled high during reset to avoid spurious writes. When designing with this part, leave at least one block as a wear-levelling reserve and use the SFDP header to confirm density before issuing read-ID commands; mismatched density detection is a common first-board bring-up failure.

طلب عرض سعر اتصل بنا
MT29F1G01ABAFDSF-AATF - 1Gbit SPI SLC NAND Flash, 16-SOIC | Micron
MT29F1G01ABAFDSF-AATF

MT29F1G01ABAFDSF-AATF - 1Gbit SPI SLC NAND Flash, 16-SOIC | Micron

The Micron MT29F1G01ABAFDSF-AATF is a 1-Gbit serial peripheral interface (SPI) SLC NAND Flash memory organized as 1 Gbit with a single 1.8 V or 3.3 V supply domain, housed in a 16-pin SOIC (300 mil) package. The AATF suffix designates the automotive-grade, -40C to +105C operating temperature window and AEC-Q100 qualification per Micron's part-number convention. The device uses a standard SPI-compatible bus with optional x2 (Dual SPI) and x4 (Quad SPI) data transfer modes for higher throughput. A SPI NAND flash is a non-volatile memory that exposes a low-pin-count serial interface instead of the wide parallel bus used by traditional raw NAND. SLC (single-level cell) NAND stores one bit per cell, offering higher endurance (typically 100k P/E cycles), lower bit-error rate, and longer data retention than MLC/TLC parts. SPI NAND sits between small SPI NOR devices (used for code storage in MCUs) and high-density managed NAND (eMMC/UFS) in the storage taxonomy, enabling densities of 1-8 Gbit with serial access. Key features include 1 Gbit density (128 MB) over 65,536 erasable blocks of 128 KB each, 2 KB page size for read/program, on-die ECC engine selectable to 1-bit or 4-bit Hamming, hardware reset, write-protect pin, and 4-byte addressing to access the full density above 128 MB. Operating voltages support 1.7 V to 2.0 V (1.8 V typical) and 2.7 V to 3.6 V (3.3 V typical) ranges. Typical applications include automotive infotainment and instrument clusters, ADAS data loggers, industrial gateways, IoT edge devices, and point-of-sale terminals where moderate-density, high-reliability non-volatile storage is required. The AEC-Q100 qualification supports under-hood and cabin automotive environments. When designing with this device, route SPI traces as 50 ohm impedance-controlled nets and place a 0.1 uF decoupling capacitor within 3 mm of VCC. The internal ECC must be enabled to maintain data integrity over the part's endurance lifetime. Hold power stable during program and erase operations to prevent block corruption.

طلب عرض سعر اتصل بنا