الدوائر المتكاملة

ADS6144IRHBR

ADS6144IRHBR - 14-Bit 105MSPS Low-Power ADC | Texas Instruments

The Texas Instruments ADS6144IRHBR is a 14-bit, 105-MSPS, low-power analog-to-digital converter (ADC) with selectable parallel CMOS or DDR LVDS outputs, housed in a 32-pin VQFN (RHB) package with 5x5 mm body and exposed thermal pad. The ADS614X family spans 65/80/105/125 MSPS sampling rates; the ADS6144IRHBR occupies the 105 MSPS position in the lineup and dissipates approximately 200 mW per channel at full Nyquist input. Integrated features include an analog input buffer, internal reference, programmable gain, and a digital down-converter block for flexible system insertion. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples a continuous-time analog voltage and quantizes it into a discrete digital code. Pipeline ADCs such as the ADS6144 use a multi-stage switched-capacitor architecture that delivers high sample rates (>100 MSPS) at moderate resolution (10-16 bit) with low latency, making them the workhorse of high-speed data acquisition. The ADS6144 belongs to the broader category of data-conversion ICs within the signal-chain semiconductor taxonomy: pipeline ADC -> ADC -> data converter -> mixed-signal IC -> semiconductor. Key features of the ADS6144IRHBR include an input bandwidth of approximately 700 MHz, spurious-free dynamic range (SFDR) above 80 dBFS at 70 MHz IF, and an SNR of about 72 dBFS at 9.9 MHz input. Programmable full-scale input range spans 1.0 Vpp to 1.5 Vpp, and the parallel CMOS bus can be configured as 1-Wire or 2-Wire DDR LVDS. The 32-pin QFN package provides a low-inductance ground reference through the exposed pad, which is essential for maintaining noise performance above 100 MSPS. Typical applications for the ADS6144IRHBR include software-defined radio (SDR) receivers, medical imaging front-ends such as ultrasound beamformers, portable test and measurement instruments, multi-carrier cellular base-station cards, and high-speed CCD imaging digitizers. The low power dissipation makes it attractive for dense multi-channel designs where thermal management is challenging. When designing with this ADC, place the input network and clock-generation components within 5 mm of the package and provide a solid ground reference beneath the exposed pad. The internal reference mode is sufficient for many applications, but for highest SFDR in multi-carrier scenarios, an external low-noise reference such as the REF5025 improves performance by 5-7 dB.

طلب عرض سعر اتصل بنا

ADS6145IRHB25

ADS6145IRHB25 - 14-bit 125MSPS Low-Power ADC | Texas Instruments

The Texas Instruments ADS6145IRHB25 is a 14-bit, 125 MSPS, low-power pipelined analog-to-digital converter with selectable parallel CMOS or LVDS output interfaces, packaged in a 32-pin VQFN (5x5 mm, RHB) exposed-pad package. It supports industrial temperature operation from -40C to +85C, runs from a 3.3V analog/digital supply, and offers one single-ended analog input channel. The device combines a high-bandwidth sample-and-hold front end with a low-jitter clock buffer to deliver high SNR and high SFDR even at high input frequencies. An ADC (Analog-to-Digital Converter) is a data-acquisition integrated circuit that samples continuous analog signals and converts them into discrete digital codes for processing by FPGAs, DSPs, or microcontrollers. Within the broader semiconductor hierarchy, the ADS6145 belongs to the data-converter IC family, sits inside the signal-chain sub-system, and is classified as a pipelined ADC because it uses a multi-stage switched-capacitor architecture to achieve high sample rates at moderate power. Pipelined ADCs are favored over SAR or delta-sigma types when sampling speed exceeds ~10 MSPS while still preserving 10-14 bit resolution. Key specifications include 125 MSPS maximum sample frequency, 14-bit resolution, selectable CMOS or LVDS digital outputs, internal sample-and-hold, and a low-jitter clock buffer. The 32-VQFN package with exposed thermal pad provides ~32 C/W junction-to-ambient thermal resistance, suitable for reflow soldering on standard FR-4 boards with moderate copper-area thermal relief. The ADS6145 architecture uses a multi-stage pipelined core with digital error correction. Its high input bandwidth allows IF sampling in software-defined radio, while the low-jitter clock path minimizes aperture-time-induced SNR degradation. Programmable gain and offset correction are performed digitally, simplifying analog front-end calibration. Typical applications include wireless base-station receivers, software-defined radio, portable test and measurement instrumentation, medical imaging front ends, and high-speed data acquisition cards. The wide analog input bandwidth also makes it suitable for digitizing IF signals in communication receivers. When designing with this device, ensure the analog input network is bandwidth-limited to the target Nyquist zone and that the LVDS/CMOS mode select pin is correctly biased before power-up. Decouple AVDD and DVDD with separate 0.1 uF and 10 uF ceramic capacitors placed as close to the IC as possible to maintain SNR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page, giving engineers a single-source reference for part selection and PCB bring-up.

طلب عرض سعر اتصل بنا

ADS6148IRGZ25

ADS6148IRGZ25 - 14-Bit 250 MSPS ADC, DDR LVDS | Texas Instruments

The Texas Instruments ADS6148IRGZ25 is a 14-bit, 250 MSPS (mega-samples per second) analog-to-digital converter (ADC) featuring a pipelined architecture and selectable DDR LVDS or parallel CMOS output interfaces, housed in a 48-pin VQFN (RGZ) 7x7 mm package with exposed thermal pad. An analog-to-digital converter (ADC) is a semiconductor device that transforms continuous analog signals into discrete digital codes for processing by digital systems. High-speed pipelined ADCs like the ADS6148IRGZ25 are widely used in communications, test and measurement, and imaging systems where signals in the tens to hundreds of MHz must be quantized for digital down-conversion, modulation analysis, or video processing. The device fits within the broader hierarchy of: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Key features include selectable DDR LVDS or parallel CMOS outputs, internal sample-and-hold with 250 MSPS maximum sampling rate, programmable full-scale input range of 1.0 Vpp to 2.0 Vpp, integrated analog input buffer, low-jitter clock input, and a 48-pin QFN package. The DDR LVDS interface doubles per-pin throughput by clocking data on both clock edges, simplifying board routing and reducing the number of FPGA pins needed. The device is built on TI's proprietary high-speed BiCMOS process, enabling 250 MSPS operation with low aperture jitter and a wide input bandwidth. It is pin-compatible with the ADS5547 family of ADCs, simplifying migration between resolution and sample-rate options within a system platform. Internal references and gain/offset correction simplify the analog front-end design. Typical applications include multicarrier wireless infrastructure, software-defined radio (SDR), power amplifier linearization, test and measurement instrumentation, high-definition video processing, medical imaging, and radar systems. When designing with this ADC, attention to the analog input network, PCB layout, and decoupling strategy is critical. Ground the exposed thermal pad to a low-impedance ground plane and route LVDS outputs with controlled 100-ohm differential impedance to preserve signal integrity. This page synthesizes current distributor pricing, parametric comparisons, pin-compatible alternatives, and practical design notes not consolidated on distributor listings.

طلب عرض سعر اتصل بنا

ADS6149IRGZ25

ADS6149IRGZ25 - 14-Bit 250MSPS Low-Power ADC | Texas Instruments

The Texas Instruments ADS6149IRGZ25 is a 14-bit, 250-MSPS pipelined analog-to-digital converter (ADC) with DDR LVDS and parallel CMOS outputs, housed in a 48-pin VQFN (7x7 mm) package. It belongs to the ADS614X/ADS612X family of low-power, high-dynamic-performance ADCs combining high sampling rates with sub-1W power consumption. The part is specified for the -40°C to 85°C industrial temperature range and operates from 1.8V analog and 3.3V digital supplies. An analog-to-digital converter (ADC) is a semiconductor device that transforms continuous analog signals into discrete digital codes for processing by DSPs, FPGAs, or microcontrollers. Pipelined ADCs use a multi-stage architecture to achieve high sampling rates while maintaining moderate resolution; they sit within the data converter hierarchy of successive-approximation-register (SAR) and flash ADCs. The ADS6149 specifically targets applications where high dynamic range and low power are required simultaneously, such as communications infrastructure and medical imaging. Key features include 250 MSPS maximum sample rate, 14-bit resolution, 687 mW total power dissipation at 250 MSPS, DDR LVDS outputs for reduced pin count at high speeds, and parallel CMOS options for flexible interfacing. The device provides excellent spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) across a wide input bandwidth, suitable for digitizing IF and baseband signals in wireless and test equipment. The ADS6149 uses a switched-capacitor pipelined architecture with internal reference and sample-and-hold, supporting both single-ended and differential analog interfaces. The integrated DDR LVDS interface enables transfer of two data bits per cycle, minimizing the number of LVDS pairs required for 250 MSPS operation. Programmable gain, offset, and test-pattern features simplify system calibration and verification in production test environments. Typical applications include wireless multi-carrier communications infrastructure, software-defined radio (SDR), power amplifier linearization, test and measurement instrumentation, high-definition video, medical imaging, and radar systems. The pin compatibility with the ADS5547 family allows designers to migrate designs across resolution/speed nodes without PCB rework. When designing with this ADC, allocate the analog and digital supply domains carefully—place 1.8V AVDD and 3.3V DRVDD decoupling capacitors close to the supply pins. Use controlled-impedance differential routing for analog inputs and 50-ohm termination on LVDS outputs to preserve signal integrity at full sample rate. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the ADS5547/ADS614X family, and practical design notes not consolidated on a single manufacturer or distributor page.

طلب عرض سعر اتصل بنا

ADS61B23

ADS61B23 - 12-Bit 80MSPS ADC, Buffered Inputs | TI

The Texas Instruments ADS61B23 is a 12-bit, 80-MSPS analog-to-digital converter (ADC) with buffered analog inputs, designed for high-performance signal acquisition in communications, test and measurement, and medical imaging systems. It operates from a 3.3V analog supply and a 1.8V digital supply, and is available in a compact 32-pin VQFN (5x5 mm) package. The device features a pipelined architecture with internal reference and supports both internal and external reference modes. An ADC (analog-to-digital converter) is a data converter that converts continuous analog signals into discrete digital values, enabling digital processing of real-world signals. The ADS61B23 is a high-speed, low-power pipelined ADC within the broader data-converter hierarchy: data converters -> ADCs -> high-speed pipelined ADCs -> mixed-signal building blocks. Its buffered inputs isolate the sampling capacitor from the source, reducing kickback and easing front-end amplifier drive requirements. Key features include 12-bit resolution, a maximum sampling rate of 80 MSPS, and a buffered differential input accepting a wide common-mode range. Dynamic performance is excellent: SNR of 69.5 dBFS and SFDR of 84 dBc at 70 MHz input frequency. The device includes an internal voltage reference, a programmable gain amplifier (PGA) option, and a flexible digital output interface with LVDS or CMOS options. Architecturally, the ADS61B23 uses a pipelined core with digital error correction, achieving high throughput at approximately 380 mW power consumption. The buffered inputs reduce the need for external drive amplifiers and simplify the analog front-end. The device also features sleep and power-down modes and an internal reference buffer that provides a stable reference voltage without external components. Typical applications include wireless base stations, software-defined radios, radar receivers, medical ultrasound, and high-speed data acquisition. Buffered inputs and high dynamic range suit direct IF sampling in communication receivers, digitizing intermediate-frequency signals with high fidelity. When designing with the ADS61B23, decouple the analog and digital supplies properly and use a low-jitter sampling clock to achieve the specified SNR. Set the input common-mode voltage to the datasheet-recommended level to optimize AC performance.

طلب عرض سعر اتصل بنا

ADS61B23IRHB25

ADS61B23IRHB25 - 12-Bit 80MSPS ADC, Buffered Diff Input | TI

The Texas Instruments ADS61B23IRHB25 is a 12-bit, 80-MSPS analog-to-digital converter with buffered differential inputs, housed in a 32-pin VQFN (RHB, 5x5 mm) package. It combines high dynamic performance with low power consumption in a compact footprint, featuring one differential input channel, a pipelined architecture, and parallel CMOS output. The wide -40C to +85C industrial operating range supports deployment in communications, instrumentation, and imaging front-ends. An ADC (analog-to-digital converter) is a data-conversion integrated circuit that samples continuous analog signals and produces discrete digital codes at a defined sampling rate. High-speed ADCs sit in the signal chain hierarchy between analog signal conditioning (amplifiers, filters) and digital processing (FPGA, ASIC, DSP), and they determine the achievable dynamic range, SNR, and spurious-free dynamic range (SFDR) of the overall system. The ADS61B23 belongs to the pipelined-architecture sub-family, which is the workhorse of 10- to 16-bit, 10- to 250-MSPS communications, medical-imaging, and test-and-measurement front-ends. Key features include 80 MSPS maximum sampling rate, 12-bit resolution, buffered differential analog inputs that ease driver and interface design, parallel CMOS digital outputs, and an internal reference. The integrated input buffer eliminates the need for an external high-bandwidth op-amp, simplifying board layout and reducing BOM count in space-constrained designs. Architecturally, the device uses a multi-stage pipelined converter with on-chip sample-and-hold and digital error correction. The buffered front-end presents a high-impedance differential load to the driving amplifier, allowing flexibility in gain-setting and anti-alias filtering, while the parallel CMOS output bus simplifies direct connection to FPGAs and ASICs without an external deserializer. Typical applications include wireless communications IF/baseband digitization, medical imaging front-ends (ultrasound, MRI), portable and benchtop test and measurement equipment, radar and lidar intermediate-frequency sampling, and high-speed data acquisition systems. The 32-VQFN package with exposed thermal pad enables compact two-layer or four-layer PCB layouts. When designing with this device, place the input anti-alias filter and common-mode bias network as close to the analog input pins as possible, and route the parallel CMOS output bus with matched trace lengths to the receiving FPGA. A solid ground plane beneath the exposed pad is critical for thermal dissipation and for reducing digital switching noise coupling into the analog front-end. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the ADS61B23IRHB25 that complement the manufacturer datasheet, including thermal, layout, and signal-integrity guidance for first-pass design success.

طلب عرض سعر اتصل بنا

ADS61B29IRGZ25

ADS61B29IRGZ25 - 12-Bit 250MSPS Buffered ADC | Texas Instruments

The Texas Instruments ADS61B29IRGZ25 is a 12-bit, 250-MSPS analog-to-digital converter with an integrated high-impedance analog input buffer, housed in a 48-pin VQFN (RGZ) 7x7 mm package. According to the manufacturer datasheet, the device combines high dynamic performance with low power consumption (790 mW typical at 250 MSPS), making it suitable for high-IF sampling receiver chains where transformer-based front ends would otherwise be required. The integrated buffer eliminates the need for an external ADC driver, simplifying board layout and reducing BOM cost while preserving signal integrity at high input frequencies. An ADC (Analog-to-Digital Converter) is a data-conversion IC that samples continuous-time analog signals and outputs discrete digital codes. The 12-bit resolution class sits in a hierarchy between 8/10-bit general-purpose converters and 14/16-bit precision converters, balancing dynamic range against conversion speed. The ADS61B29 belongs to the pipelined ADC family, which uses multiple low-resolution stages to achieve high sample rates (>100 MSPS) at moderate resolution - ideal for communications, radar, and test-and-measurement front ends where wide capture bandwidth matters more than absolute DC precision. Key features include 250 MSPS maximum sample rate, integrated high-impedance analog input buffer, LVDS parallel data interface, single 3.3V analog supply, internal sample-and-hold ratio of 1:1, and industrial operating temperature range of -40C to +85C. The pipelined architecture delivers consistent dynamic performance across the full Nyquist bandwidth, with low spurious and harmonic distortion suitable for multi-carrier receiver designs. The ADS61B29 uses a switched-capacitor pipeline core with proprietary calibration to maintain linearity, while the front-end analog buffer provides a high-impedance differential input that tolerates a wide variety of source impedances. Differential LVDS outputs minimize switching noise on the digital supply rail, allowing the part to coexist with sensitive analog circuitry on shared 3.3V planes when proper decoupling is observed. Typical applications include multi-carrier GSM/EDGE base-station receivers, cable-headend digitizers, radar and SAR signal acquisition, test-and-measurement digitizer cards, and medical imaging front-ends. The integrated buffer and 250 MSPS throughput also suit software-defined radio (SDR) platforms that need wide instantaneous bandwidth at a moderate resolution. When designing with this device, drive the analog inputs differentially (typically through a balun or active differential amplifier) to achieve the datasheet's SFDR and SNR numbers at high input frequencies; the integrated buffer reduces but does not eliminate the sensitivity to common-mode noise at the analog inputs.

طلب عرض سعر اتصل بنا

ADS61B49IRGZ25

ADS61B49IRGZ25 - 14-Bit 250MSPS Buffered ADC | Texas Instruments

The Texas Instruments ADS61B49IRGZ25 is a 14-bit, 250-MSPS pipelined analog-to-digital converter with an integrated analog input buffer, housed in a 48-pin VQFN (RGZ) package measuring 7x7 mm. The device integrates an analog input buffer that eliminates the need for an external front-end driver, simplifying board design while delivering 250 MSPS sample rate with low power consumption. According to the TI datasheet, it operates from 1.8V to 3.3V analog and digital supplies and is specified over the industrial temperature range of -40C to +85C. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that converts continuous analog waveforms into discrete digital codes at a defined sample rate. Pipelined ADCs use a multi-stage architecture to achieve high sample rates (hundreds of MSPS) with moderate resolution (10-16 bits), occupying a position in the signal chain hierarchy: sensor/buffer -> variable-gain amplifier -> ADC -> DSP/FPGA. The ADS61B49 belongs to TI's ADS61xx family of buffered-input, low-power data converters used in communications, test equipment, and industrial imaging. Key specifications include 14-bit resolution, 250 MSPS maximum sample rate, internal references eliminating the need for external reference decoupling capacitors, parallel/LVDS output interface, and an integrated input buffer that handles high source-impedance sensors directly. The 48-VQFN package provides an exposed thermal pad for low thermal resistance, supporting reliable operation across the full industrial temperature range. Architecturally, the device uses a multi-stage pipelined core with on-chip sample-and-hold and internal bandgap references. The input buffer isolates the switched-capacitor sampling front-end from external drive circuitry, improving SFDR/SNR performance when the source impedance is non-zero. The internal references remove layout sensitivity around external reference pins, a common pitfall in high-speed ADC designs. Typical applications include communications test equipment, multi-carrier GSM/UMTS/LTE base-station receivers, medical imaging front-ends, industrial ultrasound, and high-speed data acquisition systems. The buffered input makes it particularly suitable for direct connection to differential IF stages without an external op-amp driver. When designing with this device, allocate sufficient PCB area for the thermal pad and stitch vias to inner ground planes; route LVDS outputs with controlled 100-ohm differential impedance; and place input coupling capacitors and common-mode bias resistors as close to the analog input pins as the layout allows. Use a quiet, low-noise LDO such as the TPS7A4701 on the AVDD rail to maximize SFDR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. It is intended to accelerate sourcing and first-pass PCB decisions for engineers specifying a 250 MSPS buffered-input ADC.

طلب عرض سعر اتصل بنا

ADS6223IRGZR

ADS6223IRGZR - Dual 12-bit 80MSPS ADC, Serial LVDS | TI

The Texas Instruments ADS6223IRGZR is a dual-channel, 12-bit, 80 MSPS analog-to-digital converter with a serial LVDS interface, housed in a 48-pin VQFN (RGZ) exposed-pad package. The device features simultaneous sample-and-hold on both channels, 3.5 dB coarse gain, and 6 dB programmable fine gain, with no missing codes across the operating range. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples continuous analog voltages and converts them into discrete digital codes. Pipeline ADCs such as the ADS6223 family use a multi-stage switched-capacitor architecture to achieve sample rates from tens to hundreds of MSPS while maintaining low power consumption. ADCs sit in the signal chain hierarchy between analog front ends (amplifiers, filters) and digital processing blocks (FPGAs, DSPs, ASICs), and are essential in data acquisition, communications, and imaging systems where analog signals must be digitized for analysis or storage. The ADS6223IRGZR offers 12-bit resolution, programmable output data rates of 65/80/105/125 MSPS, a coarse gain of 3.5 dB and a programmable fine gain of up to 6 dB, and a serial LVDS output interface for low-noise board-level data transfer. Internally, two simultaneously-sampling track-and-hold stages feed a shared pipelined core that delivers deterministic latency suitable for I/Q demodulation. The device is specified over the industrial -40C to +85C temperature range and operates from a single 3.3 V analog and digital supply. Typical applications include medical imaging ultrasound front ends, multichannel industrial data acquisition cards, communications receiver I/Q baseband digitization, and handheld test and measurement instruments. The LVDS serial interface reduces board trace count compared to parallel CMOS ADCs, enabling dense multi-channel layouts on standard FR-4. When designing with this device, provide low-impedance decoupling on each supply pin and a quiet analog ground plane to achieve the rated SNR. The exposed thermal pad must be soldered to the PCB ground for both thermal dissipation and electrical reference; failing to solder the EP will degrade linearity and may cause device failure. This page consolidates distributor pricing, drop-in alternatives, and practical design notes not present on the manufacturer product page or in the standalone datasheet.

طلب عرض سعر اتصل بنا

ADS6224IRGZ25

ADS6224IRGZ25 - Dual 12-Bit 105MSPS ADC LVDS | Texas Instruments

The Texas Instruments ADS6224IRGZ25 is a dual-channel, 12-bit, 105-MSPS pipelined analog-to-digital converter (ADC) with a serialized LVDS output interface, housed in a 48-pin VQFN (RGZ) package measuring 7x7 mm. It integrates two simultaneously-sampling 12-bit ADCs capable of up to 105 MSPS per channel with no missing codes, plus an internal reference that can be overridden by an external source for improved absolute accuracy or ADC-to-ADC gain matching. The part is specified over the industrial temperature range of -40 °C to +85 °C, making it suitable for harsh-environment signal chains. A pipelined ADC is a high-speed data-converter architecture that resolves each input sample through a chain of low-resolution stages with digital error correction, delivering high sample rates (tens to hundreds of MSPS) at moderate resolution (8-14 bits). Pipelined ADCs sit higher than successive-approximation (SAR) ADCs in the speed/resolution trade-off but lower than flash ADCs in raw analog bandwidth; they are members of the broader data-converter IC family, which also includes delta-sigma, SAR, and flash topologies. The ADS6224 belongs to TI's high-speed converter portfolio targeting communications, instrumentation, and defense imaging subsystems. Key features include a maximum sample rate of 125 MSPS (the 105-MSPS grade shipped as IRGZ25 is pin-compatible with the 65/80/105/125 MSPS variants), simultaneous sample-and-hold for both channels, a 3.5 dB coarse gain option plus a 6 dB programmable fine gain, serialized LVDS output for low-EMI high-speed data transfer, and a 1.8 V analog / 3.3 V LVDS supply split. Total power dissipation is approximately 320 mW per channel at 105 MSPS, and the LVDS interface reduces board-routing complexity versus parallel CMOS outputs at >100 MSPS. The ADS6224 uses a multi-stage pipeline with an internal sample-and-hold and supports both single-wire and dual-wire LVDS serialization to flex with board density and FPGA capture budgets. Its LVDS topology generates far less switching noise than parallel CMOS outputs, easing EMI compliance in dense multi-channel systems such as 4G base-station receivers and phased-array radar digitizers. Typical applications include communications base-station receivers (multi-carrier GSM, LTE, WCDMA), multi-channel wireless infrastructure, medical imaging front-ends (ultrasound beamformers), defense and instrumentation (synthetic aperture radar, oscilloscope data acquisition), and dual-channel IF-sampling designs where both I and Q paths must be digitized concurrently with matched gain. When designing with this device, decouple AVDD (1.8 V) and LVDDR (3.3 V) supplies independently with 1 µF + 100 nF ceramic capacitors placed within 5 mm of the supply pins, and provide a solid low-impedance ground plane under the exposed thermal pad. Route the LVDS output pairs with 100 Ω differential impedance and length-match within 150 ps to minimize inter-symbol jitter at the FPGA receiver. This page synthesizes distributor pricing, drop-in same-package alternatives (ADS6242IRGZR, ADS6243IRGZR, ADS6244IRGZRG4 from the same TI family), and practical design notes not found on the bare manufacturer datasheet.

طلب عرض سعر اتصل بنا

ADS6224IRGZR

ADS6224IRGZR - 12-bit 105MSPS Dual ADC LVDS | Texas Instruments

The Texas Instruments ADS6224IRGZR is a dual-channel, 12-bit, 105-MSPS analog-to-digital converter (ADC) with a serial LVDS interface, housed in a 48-pin VQFN (RGZ) 7x7 mm package with exposed thermal pad. It supports input voltages of 3.3 V nominal and provides simultaneous sample-and-hold on both channels with a pipelined architecture and no missing codes at 12-bit resolution. An analog-to-digital converter (ADC) is a semiconductor device that converts continuous analog signals into discrete digital codes, enabling digital signal processing, storage, and transmission. High-speed ADCs sit at the boundary between the analog and digital domains and are critical for applications including communications infrastructure, medical imaging, defense electronics, and industrial test and measurement. The ADS6224 belongs to TI's high-speed ADC portfolio, where the LVDS (Low-Voltage Differential Signaling) interface family is preferred for low-noise, high-speed data transfer across PCB traces and into downstream FPGAs or ASICs. Key specifications include a maximum sample rate of 125 MSPS (with the ADS6224IRGZR specifically rated for 105 MSPS), 12-bit resolution, 3.5 dB coarse gain, 6 dB programmable fine gain, dual simultaneous sampling, and a 48-VQFN (HVQCCN) package. Industrial temperature grade -40 °C to +85 °C operation is supported. The pipelined core architecture multiplies per-channel sample rate while preserving low-latency conversion, and the integrated gain stages simplify front-end signal conditioning for inputs that exceed the ADC's full-scale range. The dual-channel simultaneous sampling and LVDS output make the ADS6224IRGZR well suited for communications baseband I/Q capture, ultrasound beamforming, and multi-channel instrumentation. The 105 MSPS per-channel rate supports IF sampling of signals in the tens of MHz and direct RF undersampling in some architectures. Programmable gain allows system designers to optimize dynamic range without external attenuators, and the LVDS output minimizes EMI by using differential signaling, which is essential in dense, multi-layer boards. Typical applications include communications receivers (baseband I/Q digitizers), medical ultrasound imaging front-ends, industrial digitizers and oscilloscopes, radar signal processing, and defense electronic warfare systems. When designing with this ADC, ensure the LVDS data and clock traces are length-matched (typically within 5-10 mils) and routed with controlled 100-ohm differential impedance. Decouple AVDD and DVDD supplies separately and provide a clean low-jitter clock to the CLK input to preserve SNR. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB/layout design notes that complement the manufacturer datasheet and help engineers shorten their selection and procurement cycle.

طلب عرض سعر اتصل بنا

ADS6225IRGZR

ADS6225IRGZR - Dual 12-Bit 125MSPS ADC, Serial LVDS | TI

The Texas Instruments ADS6225IRGZR is a dual-channel, 12-bit, 125 MSPS pipelined analog-to-digital converter with serialized LVDS outputs, housed in a 48-pin VQFN (RGZ, 7x7 mm) package. It features two simultaneously-sampling inputs, on-chip sample-and-hold, 3.5 dB coarse gain plus up to 6 dB programmable fine gain for SFDR/SNR trade-off, and serialized LVDS output with one-wire or two-wire modes for flexible board routing. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples a continuous-time analog waveform and produces a discrete binary code at its output. Pipelined ADCs, like the ADS6225, use a multi-stage architecture with per-stage residue amplifiers and digital error correction, enabling high sample rates (tens to hundreds of MSPS) while consuming moderate power. ADC products are a sub-category of data converters, which themselves sit within the broader mixed-signal / power-management IC hierarchy used in virtually every signal acquisition system. Key features include 12-bit resolution with no missing codes, simultaneous sample-and-hold on both channels, internal reference option, and an external reference mode for gain scaling. The serialized LVDS interface reduces parallel-digital switching noise on the board and simplifies timing closure at 125 MSPS. A 3.3 V analog supply with a separate digital I/O supply rail (DVDD) supports low-EMI integration with FPGAs. Industrial temperature range (-40C to +85C) and AEC-Q100-grade die pedigree make this family attractive for harsh-environment signal chains. Typical applications include multi-antenna wireless base-station receiver IF digitizers, medical ultrasound beamforming front ends, portable and bench-top oscilloscopes, dual-channel communications test equipment, and industrial imaging / vibration analysis. The wide SFDR/SNR gain tuning lets designers trade linearity for noise on a per-channel basis. When designing with this device, allocate a quiet analog ground plane and decouple AVDD with 1 uF plus 0.1 uF ceramics placed within 3 mm of each supply pin. The serialized LVDS link must be length-matched within 1 cm and terminated with 100 ohm differential at the FPGA bank. Verify FPGA LVDS-25/-33 bank compatibility before PCB commitment.

طلب عرض سعر اتصل بنا

ADS6242IRGZR

ADS6242IRGZR - 14-Bit, 65MSPS Dual-Channel LVDS ADC | Texas Instruments

The Texas Instruments ADS6242IRGZR is a dual-channel, 14-bit, 65-MSPS analog-to-digital converter (ADC) with serial LVDS outputs, housed in a 48-pin VQFN (RGZ) 7x7 mm package. The ADS6242 family covers 125/105/80/65 MSPS sampling rates, and the IRGZRZ suffix identifies the 65 MSPS speed grade in tape-and-reel packaging on the 7x7 mm QFN footprint. Serial LVDS data outputs reduce the number of interface lines, enabling compact board layouts and high system integration density. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that samples continuous analog input signals and converts them into discrete digital codes at a specified sampling rate. High-speed ADCs such as the ADS6242 family sit at the front-end of the signal chain in communications infrastructure, medical imaging, defense electronics, and test-and-measurement equipment, where they digitize wideband IF or baseband signals for downstream DSP, FPGA, or ASIC processing. They are part of the broader pipeline-ADC architecture family, characterized by multi-stage sample-and-hold conversion that achieves high sample rates at moderate-to-high resolution. Key features of the ADS6242 include a 3.5 dB coarse gain option that improves SFDR (spurious-free dynamic range) performance with minimal SNR (signal-to-noise ratio) degradation, serial LVDS outputs that simplify PCB routing and reduce EMI, internal references that reduce external component count, and a 48-pin VQFN package providing excellent thermal performance. The dual-channel architecture with independent sample-and-hold circuits supports simultaneous sampling, critical for I/Q radio chains and beamforming applications. From an architectural perspective, the ADS6242 uses a pipelined multi-stage conversion core followed by digital error correction. The coarse gain option is implemented as an analog front-end attenuator that backs off the input signal below the converter's full-scale range, which pushes the signal away from the nonlinear regions of the input sampling network and improves large-signal SFDR. Typical applications include wireless communications basestation receivers, software-defined radio (SDR) platforms, medical ultrasound imaging front-ends, defense radar signal processing, and high-speed data acquisition systems. The dual-channel simultaneous sampling makes the ADS6242 ideal for I/Q demodulation, diversity reception, and multi-antenna systems. Designers should note that input common-mode voltage, clock jitter, and input bandwidth all directly impact achievable SNR - careful PCB layout and a low-jitter clock source are essential. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not aggregated on the manufacturer product page.

طلب عرض سعر اتصل بنا

ADS6243IRGZR

ADS6243IRGZR - Dual 14-Bit 80MSPS ADC w/ LVDS | Texas Instruments

The Texas Instruments ADS6243IRGZR is a dual-channel, 14-bit, 80-MSPS pipelined analog-to-digital converter (ADC) with serialized LVDS outputs, housed in a 48-pin VQFN (RGZ) package measuring 7x7 mm. It supports four speed grades from 65 to 125 MSPS in the broader ADS624x family while the ADS6243 variant specifically delivers 80 MSPS per channel with no missing codes. An ADC (analog-to-digital converter) is a data-conversion integrated circuit that samples continuous analog voltages and quantizes them into discrete digital codes for processing by DSPs, FPGAs, or microcontrollers. Pipelined ADCs like the ADS6243 use a multi-stage architecture that converts one sample per clock cycle after a fixed latency, combining high throughput with small die area. Within the broader data-converter taxonomy, the ADS6243 sits under high-speed ADCs -> Nyquist-rate ADCs -> pipeline ADCs -> mixed-signal ICs. Key features include 14-bit resolution with guaranteed no missing codes, simultaneous sample-and-hold on both channels, 3.5 dB coarse gain plus up to 6 dB programmable fine gain for SFDR/SNR trade-off, serialized LVDS outputs that reduce pin count and ease board routing, internal reference with external reference support, and a 3.3-V analog/digital supply. The LVDS interface delivers data over a small number of differential pairs, minimizing EMI in dense multi-channel designs. Architecturally the device uses a switched-capacitor pipelined front end with on-chip reference buffer and integrated LVDS drivers. The simultaneous dual sample-and-hold simplifies front-end alignment for I/Q or diversity receivers, while the programmable gain allows per-channel SFDR optimization. According to the Texas Instruments datasheet, the pin-compatible 12-bit family is the ADS622X and the feature-compatible quad-channel family is the ADS644X/ADS642X. Typical applications include multi-channel wireless infrastructure receivers, medical imaging front ends, radar and sonar signal processing, and high-speed instrumentation. The wide input common-mode range down to 400 mVpp supports direct-IF sampling in cost-sensitive designs. When designing with this part, choose the input-driver op amp (e.g., THS4503 or OPA695) and anti-alias filter topology carefully because the 80 MSPS input bandwidth is well above the Nyquist limit and any front-end distortion directly degrades SFDR. This page synthesizes verified distributor pricing, drop-in same-package alternatives from the ADS6xxx family, and practical design notes that go beyond what is printed in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

ADS6244IRGZ25

ADS6244IRGZ25 - Dual 14-Bit 105MSPS Serial LVDS ADC | Texas Instruments

The Texas Instruments ADS6244IRGZ25 is a dual-channel, 14-bit, 105 MSPS analog-to-digital converter (ADC) with serialized LVDS outputs, housed in a 48-pin VQFN (RGZ) 7x7 mm package. It integrates two simultaneous sample-and-hold amplifiers, an internal reference, and programmable coarse (3.5 dB) and fine (up to 6 dB) gain stages for SFDR/SNR trade-off optimization. The device supports input amplitudes down to 400 mVpp and operates from a single 3.3 V analog and digital supply. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes at a specified sample rate. The ADS6244 belongs to the high-speed pipeline ADC class, which excels at sampling IF/RF signals in the 1-100+ MHz range with 10-16 bit resolution. Within TI's power-management and data-converter hierarchy, the ADS6244 sits as a precision signal-chain component, frequently paired with low-noise LDOs, differential amplifiers, and FPGA/ASIC LVDS receivers to build complete digital signal acquisition subsystems. The ADS6244's serialized LVDS interface reduces board trace count by 6x compared to parallel CMOS outputs, simplifying PCB routing and lowering EMI in dense multi-channel systems. The integrated sample-and-hold and internal reference eliminate the need for external reference decoupling, reducing BOM cost. Programmable gain allows system designers to optimize spurious-free dynamic range (SFDR) versus signal-to-noise ratio (SNR) at the system level without external attenuators. Per TI documentation, the device is part of a pin-compatible 12-bit family (ADS622X) and a feature-compatible quad-channel family (ADS642X/ADS644X), enabling board reuse across performance tiers. The architecture is a multi-stage pipeline with per-stage error correction, supporting 14-bit no-missing-codes performance at the full 105 MSPS rate. Built-in self-test patterns, a serial peripheral interface (SPI) for mode configuration, and integrated LVDS termination simplify FPGA interface design. The 48-VQFN package with exposed thermal pad achieves 31.4 C/W theta_JA, adequate for industrial temperature operation at -40C to +85C. Typical applications include medical imaging ultrasound receivers, communications IF/baseband digitizers, multi-channel software-defined radio (SDR) platforms, industrial vibration analysis, and high-speed test and measurement instrumentation. In each case, the dual-channel architecture saves PCB area versus two discrete ADCs and the LVDS interface minimizes FPGA pin count. When designing with the ADS6244IRGZ25, allocate adequate copper pour under the exposed pad and decouple AVDD/DVDD with 0.1 uF ceramic capacitors placed within 5 mm of each supply pin. The serialized LVDS data rate reaches 595 Mbps per channel at 105 MSPS - verify FPGA LVDS receiver capabilities and PCB controlled-impedance (100 ohm differential) routing before final layout. This page synthesizes distributor pricing, pin-compatible same-family variants, and application-specific design guidance beyond the manufacturer datasheet, enabling faster BOM decisions for dual-channel 105 MSPS designs.

طلب عرض سعر اتصل بنا

ADS62C17IRGC25

ADS62C17IRGC25 - Dual 11-Bit 200MSPS ADC | Texas Instruments

The Texas Instruments ADS62C17IRGC25 is a dual-channel, 11-bit, 200 MSPS analog-to-digital converter (ADC) that combines high dynamic performance and low power consumption in a compact 64-pin VQFN (9x9mm) package with exposed thermal pad. The device integrates TI-proprietary SNRBoost technology that can be selectively enabled to overcome quantization-noise-limited SNR for bandwidths less than Nyquist, delivering a measured 79.8 dBFS SNR at 125 MHz input and 90 dBc SFDR at Fin = 10 MHz. An ADC (Analog-to-Digital Converter) is a data-converter integrated circuit that samples continuous-time analog signals and outputs discrete digital codes, forming the bridge between the analog front-end and the digital signal-processing domain. Pipeline ADCs such as the ADS62C17 sit within the data converter taxonomy between successive-approximation-register (SAR) and flash architectures; they are well suited to high sampling rates (tens to hundreds of MSPS) while maintaining 10-14 bit resolution and excellent dynamic range, making them the workhorse of wireless infrastructure, test instrumentation, and imaging receivers. Key features of the ADS62C17 include a maximum sample rate of 200 MSPS, 11-bit resolution with no missing codes, an LVDS-parallel and parallel CMOS digital output interface, two differential analog inputs each feeding a sample-and-hold stage, and a 1:1 sample-to-ADC ratio per channel. The integrated SNRBoost block digitally shapes out-of-band quantization noise away from a programmable band of interest, allowing up to 4 dB SNR improvement for narrowband communications receivers. Architecturally, the ADS62C17 uses two matched pipeline cores preceded by differential input buffers and wideband track-and-hold amplifiers; the SNRBoost digital post-processing engine runs after the pipeline cores and is configured via SPI or parallel control pins. The 64-pin QFN package provides a low-inductance ground reference and exposed thermal pad that keeps junction-to-ambient thermal resistance low for the 1.1 W typical power dissipation at 200 MSPS. Typical applications include multi-carrier, wide-bandwidth cellular base-station receivers, software-defined radio (SDR) platforms, medical imaging front-ends (ultrasound, MRI), and high-speed test and measurement digitizers. The wide input bandwidth and dual channels also suit radar signal processing and cable infrastructure digitizers. When designing with this device, pay attention to the LVDS output timing budget: each data lane toggles at up to 200 MHz DDR and requires matched-length PCB routing and a 100 ohm differential termination as specified in the datasheet. The exposed pad must be soldered to a continuous ground plane to achieve the rated thermal and dynamic performance. This page synthesizes distributor stock data, cross-reference alternatives, design considerations, and pinout information from the Texas Instruments ADS62C17 datasheet - material that augments the bare datasheet with practical procurement and design context.

طلب عرض سعر اتصل بنا

ADS62C17IRGCR

ADS62C17IRGCR - Dual 11-Bit 200MSPS ADC | Texas Instruments

The Texas Instruments ADS62C17IRGCR is a dual-channel, 11-bit, 200-MSPS pipelined analog-to-digital converter in a 64-pin VQFN (RGC, 9x9 mm) package with exposed thermal pad. It combines high dynamic performance with low power consumption, making it ideal for multi-carrier, wide-bandwidth communications applications. The device features TI proprietary SNRBoost technology and supports parallel, serial, and LVDS output interfaces. An analog-to-digital converter (ADC) is a critical data-converter component that converts continuous analog signals into discrete digital values for digital signal processors and FPGAs. The ADS62C17 belongs to the high-speed pipelined ADC family, designed for sampling rates in the hundreds of mega-samples per second, and sits within the broader data-acquisition hierarchy used in communications, test and measurement, and radar systems. Key features include dual 11-bit resolution with no missing codes, a maximum sampling rate of 200 MSPS, 90 dBc SFDR at Fin = 10 MHz, and 79.8 dBFS SNR at a 125 MHz input per TI data. The 64-VQFN package includes an exposed thermal pad for heat dissipation. The device operates from a 3.3V analog supply and 1.8V digital supply with typical power consumption of 1.1 W. The ADS62C17 uses a pipelined architecture with digital error correction, achieving excellent linearity. SNRBoost digitally processes the output to improve SNR in a selected frequency band, particularly useful in multi-carrier receivers where weak signals must be extracted from strong interferers. It also includes an internal reference and a flexible clock input with duty-cycle stabilization. Typical applications include multi-carrier GSM/UMTS/LTE base stations, software-defined radios, radar systems, and test and measurement equipment. The high sampling rate and dynamic performance suit direct IF sampling architectures, reducing system complexity and cost. When designing with this ADC, pay careful attention to power supply decoupling and clock jitter, as both directly impact SNR and SFDR. The exposed pad must be soldered to a solid ground plane to ensure proper thermal and electrical performance. Pricing as of 2026-08-30 should be confirmed with distributors.

طلب عرض سعر اتصل بنا

ADS62P15IRGC25

ADS62P15IRGC25 - Dual 11-Bit 125MSPS ADC | Texas Instruments

The Texas Instruments ADS62P15IRGC25 is a dual-channel, 11-bit, 125-MSPS analog-to-digital converter (ADC) with parallel CMOS and DDR LVDS outputs, packaged in a 64-pin VQFN (9x9 mm, RGC) thermally-enhanced package. The device supports two simultaneously-sampled analog input channels at sampling rates up to 125 MSPS and integrates low-jitter clocking for high spurious-free dynamic range (SFDR) in baseband and IF-sampling architectures. An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes at a sampling rate governed by an external clock. In the broader hierarchy (MFP > data converter > ADC > pipeline ADC > high-speed ADC), pipeline ADCs like the ADS62P15 are widely used in communications, imaging, and instrumentation because they offer an excellent balance of sampling rate, resolution, and power efficiency. The ADS62P15 uses an internal reference and provides differential analog inputs optimized for high IF frequency capture. Key features include 11-bit resolution, 125 MSPS maximum sampling rate per channel, dual simultaneously-sampled channels, selectable CMOS or DDR LVDS output interfaces, integrated internal reference, low-jitter clock buffer, and a serial programming interface (SPI) for mode configuration. Typical differential input full-scale is programmable, and the integrated buffer simplifies PCB routing by eliminating the need for an external reference decoupling network. The ADS62P15 architecture combines a differential pipelined input stage with digital error correction and an output multiplexer for CMOS/DDR LVDS modes. Internal averaging and calibration maintain low integral and differential nonlinearity (INL/DNL), enabling SFDR greater than 80 dBFS at intermediate frequencies and SNR performance suitable for multi-carrier wireless receivers. Typical applications include wireless infrastructure base-station receivers (LTE, W-CDMA, TD-SCDMA, WiMAX), medical imaging (ultrasound beamforming), radar and sonar digitizers, test and measurement instrumentation, and multi-channel data acquisition systems. The dual-channel architecture reduces board space by replacing two single-channel ADCs. When designing with this part, ensure the analog inputs are DC-coupled or AC-coupled with proper common-mode biasing, and follow datasheet guidelines for analog input balun or op-amp driver selection. Decoupling of AVDD and DVDD supplies is critical to achieving datasheet SFDR performance at high input frequencies. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes not aggregated on individual distributor product pages, providing a single engineering reference for the ADS62P15IRGC25.

طلب عرض سعر اتصل بنا

ADS62P22IRGC25

ADS62P22IRGC25 - Dual 12-Bit 65MSPS ADC | Texas Instruments

The Texas Instruments ADS62P22IRGC25 is a dual-channel, 12-bit, 65-MSPS analog-to-digital converter (ADC) housed in a 64-pin VQFN (RGC) package measuring 9x9 mm. It combines two pipeline ADC cores with a shared reference, configurable CMOS or DDR LVDS digital interfaces, and a flexible gain/channel-control block to support a wide range of baseband, IF-sampling, and imaging designs. What is a pipeline ADC? A pipeline analog-to-digital converter is a high-speed Nyquist-rate architecture that processes an input sample through a sequence of low-resolution flash or multiplying-DAC stages, each handling a fraction of the overall conversion and yielding one output sample per clock cycle after pipeline latency is filled. Within the broader IC taxonomy it sits alongside successive-approximation (SAR), flash, and sigma-delta converters, occupying the niche where 10-14 bit resolution and tens-to-hundreds of MSPS are required, as in communications, instrumentation, and medical imaging. Key features include a maximum sample rate of 65 MSPS per channel, integrated digital processing with fine gain correction in 0.05 dB steps, and a coarse 3.5 dB gain stage that lets the user trade dynamic range against SNR. The 12-bit core guarantees no missing codes across the full operating range, and the part shares a footprint and digital interface with TI's pin-compatible 14-bit ADS62P4x family, simplifying upgrades and A/B testing between resolutions. Architecture-wise, the device uses differential input buffers, on-chip references, and a selectable output mode that lets one PCB layout drive parallel CMOS or DDR LVDS signaling. The 64-pin HVQCCN package exposes analog and digital supplies separately, enabling isolation between noisy digital return currents and sensitive analog ground references for high spurious-free dynamic range (SFDR). Typical applications include multi-carrier wireless infrastructure receivers, ultrasound beam-former front ends, portable medical imaging data acquisition, and dual-channel IF digitisation in software-defined radios. The device's 95 dB channel-to-channel crosstalk and integrated gain control make it particularly attractive where two matched channels are required without external matching networks. When designing in this ADC, decouple AVDD and DRVDD separately and place a low-impedance ground return directly under the exposed thermal pad to minimise digital noise coupling into the analog front end. Always verify input common-mode and clock duty cycle against the datasheet specifications to maintain SFDR performance.

طلب عرض سعر اتصل بنا

ADS62P23IRGC25

ADS62P23IRGC25 - Dual 12-bit 80MSPS ADC, DDR LVDS/CMOS | TI

The Texas Instruments ADS62P23IRGC25 is a dual-channel 12-bit analog-to-digital converter (ADC) with a maximum sample rate of 80 MSPS, housed in a 64-pin VQFN (RGC) package measuring 9x9 mm. The device integrates a high-performance pipeline architecture with selectable double-data-rate (DDR) LVDS or parallel CMOS output interfaces, giving designers flexibility to balance pin count, board area, and downstream FPGA/ASIC interface complexity. Internal references are included, which eliminates the traditional external reference pins and associated decoupling capacitors, while the device still supports an external reference drive when needed. An analog-to-digital converter (ADC) is a data-conversion IC that translates a continuous analog input voltage into a discrete digital code at each sampling clock edge. Within the signal chain taxonomy, the ADS62P23 belongs to the pipeline ADC sub-family, which sits between successive-approximation register (SAR) ADCs (low speed, low power) and flash ADCs (very high speed, high power). Pipeline ADCs dominate the 10-250 MSPS speed range because they multiplex many low-resolution stages behind a high-speed input, delivering high sample rates with moderate power budgets and small footprints. The ADS62P2X family specifically targets wideband communications, IF-sampling radios, and multi-channel industrial imaging. Key features include 80 MSPS guaranteed sample rate, 12-bit resolution across two simultaneously-sampled channels (2x2 channel matrix is supported via the family), and a wide analog input bandwidth of approximately 450 MHz. The integrated DDR LVDS interface delivers two data bits per clock cycle on each LVDS pair, halving the required FPGA pin count compared to parallel CMOS. Typical uses cover test and measurement digitizers, communications base-station receivers, medical ultrasound beamformers, and defense signal-intelligence capture cards. Industrial-grade -40C to +85C operation ensures deployment in uncontrolled enclosures. When designing with the device, prioritize short, matched-length traces between the analog inputs and the ADC; place the analog input RC network as close to the analog input pins as the layout allows to preserve SNR/SFDR. The combination of integrated references, selectable output interface, and the 9x9 mm VQFN footprint simplifies board layout versus older ADCs that required external references and LVDS buffers. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet.

طلب عرض سعر اتصل بنا

ADS62P25IRGC25

ADS62P25IRGC25 - Dual 12-Bit 125 MSPS ADC, 64-VQFN | Texas Instruments

The Texas Instruments ADS62P25IRGC25 is a dual-channel, 12-bit, 125 MSPS analog-to-digital converter (ADC) housed in a 64-pin VQFN (RGC) 9x9 mm package. The device combines high dynamic performance with low power consumption and supports both parallel CMOS and DDR LVDS output interfaces in a single part. Maximum sample rate is 125 MSPS with 12-bit resolution and no missing codes, while the dual internal sample-and-hold and low-jitter clock buffer deliver high SNR and high SFDR at IF inputs. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltages and quantizes them into discrete digital codes. The ADS62P25 sits in the high-speed pipeline ADC family, used when systems require many tens of megasamples per second per channel for communications, imaging, or instrumentation. It belongs to the hypernym hierarchy: ADC -> data converter -> data acquisition IC -> mixed-signal IC -> semiconductor. Pipeline ADCs specifically use a switched-capacitor architecture that resolves a few bits per stage across cascaded stages to achieve high sample rates at moderate resolution, which is exactly the architecture used here. Key features include 12-bit resolution with no missing codes, 125 MSPS maximum sample rate, programmable fine gain up to 6 dB plus a 3.5 dB coarse gain for SNR/SFDR trade-off, 95 dB channel-to-channel crosstalk, and a built-in digital processing block with offset correction and fine gain correction in 0.05 dB steps. Selectable DDR LVDS or parallel CMOS outputs let the same hardware target FPGA-based capture boards or legacy parallel DSP interfaces. The integrated low-jitter clock buffer simplifies board design by relaxing external clock requirements. Typical applications include multi-carrier GSM/UMTS/LTE base-station receivers, cable-headend digitizers, medical imaging front ends, radar and phased-array IF sampling, and test and measurement instrumentation. The wide input bandwidth and selectable output interfaces make it well suited for both diversity receivers and multi-channel oscilloscope platforms. When designing with this device, treat the analog input network and clock distribution as a single RF subsystem: use a differential transformer driver, keep the clock path short, and provide adequate decoupling on each supply pin. The dual-channel footprint requires that both inputs be impedance-matched to achieve the rated crosstalk and SFDR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

ADS62P28IRGC25

ADS62P28IRGC25 - Dual 12-Bit 210-MSPS ADC with DDR LVDS/CMOS | TI

The Texas Instruments ADS62P28IRGC25 is a dual-channel, 12-bit, 210-MSPS analog-to-digital converter (ADC) with DDR LVDS and parallel CMOS outputs, housed in a 64-pin VQFN (RGC) power-thermally enhanced package with exposed pad. The part integrates two high-performance pipelined ADC cores, a flexible digital interface, and on-chip sample-and-hold amplifiers optimized for multi-carrier, wide-bandwidth signal capture. An analog-to-digital converter is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes at a specified sampling rate. High-speed ADCs such as the ADS62P28 sit at the boundary between the analog front-end (amplifiers, filters, baluns) and the digital back-end (FPGAs, ASICs, DSPs). The 12-bit 210-MSPS class is commonly deployed in communications infrastructure, medical imaging, and industrial test equipment where cost-effective quantization of IF/RF signals is required. Key features include dual-channel sampling up to 210 MSPS, selectable DDR LVDS or parallel CMOS outputs, programmable full-scale input range, internal dither for spurious-free dynamic range (SFDR) improvement, and a low-jitter clock buffer with divide-by-2/4 options. The pipelined architecture provides low latency (typically 3-4 clock cycles) and excellent linearity across the operating temperature range. The 64-VQFN package with exposed thermal pad supports the 1.7 W typical power dissipation with standard PCB thermal design. The ADS62P28 uses a switched-capacitor pipelined core with on-chip reference, supporting single-ended or differential analog inputs with up to 2 Vpp full-scale. The digital output stage can be configured for either LVDS (for high-speed serial data transfer to an FPGA) or parallel CMOS (for direct connection to lower-speed digital ASICs). Built-in digital features include programmable gain, offset correction, and a test-pattern generator for board-level bring-up. Typical applications include wireless communications receivers (LTE, WCDMA, multi-carrier GSM base stations), cable infrastructure (DVB-SC, DOCSIS downstream/upstream), radar and electronic-warfare intermediate-frequency digitizers, medical ultrasound beamformers, and high-speed data acquisition for industrial test and measurement. The dual-channel architecture enables I/Q or diversity reception in a single chip. When designing with this part, ensure the analog input common-mode voltage and clock jitter budget meet the SNR specification. Use the exposed thermal pad with adequate copper area for heat removal, and place decoupling capacitors as close as possible to the supply pins. This page synthesizes distributor pricing, drop-in alternatives from TI's ADS62Pxx family, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

ADS62P42IRGC25

ADS62P42IRGC25 - Dual 14-bit 65MSPS ADC, LVDS/CMOS | Texas Instruments

The Texas Instruments ADS62P42IRGC25 is a dual-channel, 14-bit analog-to-digital converter (ADC) with a maximum sample rate of 65 MSPS per channel, offered in a 64-pin VQFN (RGC) package with exposed thermal pad. The device combines high dynamic performance and low power consumption, supports selectable Double Data Rate (DDR) LVDS or parallel CMOS outputs, and integrates an internal voltage reference and sample-and-hold to simplify multi-carrier, wide-bandwidth signal-chain designs. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous-time analog input signals and produces discrete-time digital codes proportional to the input voltage. Pipeline ADCs such as the ADS62P42 family achieve high sampling rates (>10 MSPS) at moderate-to-high resolution (12-16 bit) by distributing the conversion across multiple low-resolution stages. Within the broader taxonomy, the ADS62P42 belongs to the pipeline ADC class, which itself sits under successive-approximation and flash hybrids on the high-speed converter hierarchy: ADC -> high-speed ADC -> pipeline ADC -> data converter IC -> mixed-signal semiconductor. Understanding this hierarchy helps engineers compare against SAR, sigma-delta, and integrating architectures for each application. Key specifications include 14-bit resolution across two simultaneous channels, a 65 MSPS maximum sample rate per channel, internal reference (with optional external reference input), and DDR LVDS or CMOS digital interface. The device also includes a low-jitter clock buffer, configurable input full-scale range via the CTRL pins, and a serial peripheral interface (SPI) for advanced programming of internal registers, while simple modes can be set by parallel pin voltages at power-up. Typical applications include multi-carrier wireless base-station receivers (LTE, WCDMA, TD-SCDMA, WiMAX), test and measurement instrumentation, medical imaging front ends (ultrasound beamforming), defense radar and signal-intelligence capture, and software-defined radio (SDR) platforms. The dual-channel architecture simplifies PCB layout for I/Q signal chains by providing matched ADCs on a single die. The integrated reference eliminates external reference noise and trimming cost, and the DDR LVDS interface reduces the FPGA pin count by clocking data on both edges of the output strobe. When designing with this device, ensure the analog inputs are AC- or DC-coupled with proper 50-ohm or transformer termination, and follow TI's recommended decoupling scheme - typically a 10uF bulk plus 0.1uF and 10nF ceramics on each supply pin. The exposed pad must be soldered to a continuous ground plane to meet thermal and signal-integrity specifications.

طلب عرض سعر اتصل بنا

ADS62P44IRGC25

ADS62P44IRGC25 - Dual 14-bit 105MSPS ADC, LVDS/CMOS | TI

The Texas Instruments ADS62P44IRGC25 is a dual-channel, 14-bit, 105-MSPS analog-to-digital converter (ADC) with selectable DDR LVDS or parallel CMOS outputs, housed in a 64-pin VQFN (RGC) package sized 9x9 mm. It combines high dynamic performance with low power consumption, supporting SNR up to 72.4 dBFS and SFDR up to 85 dBc at 105 MSPS with a 70 MHz input. The integrated low-jitter clock buffer and internal sample-and-hold simplify board-level design while preserving timing margin in multi-channel systems. An ADC (analog-to-digital converter) is a data-conversion integrated circuit that quantizes continuous analog signals into discrete digital codes for downstream DSP, FPGA, or ASIC processing. Within the broader signal-chain hierarchy, an ADC sits between the analog front end (amplifiers, anti-alias filters) and the digital back end, and is classified as a high-speed pipelined ADC when sample rates exceed tens of MSPS. The ADS62P44 belongs to TI's ADS62P4x family of dual 14-bit pipelined ADCs designed for communications, radar, and test-and-measurement applications. Key features include 105 MSPS maximum sample rate per channel, 14-bit resolution, 72.4 dBFS SNR, 85 dBc SFDR, 2.3 GHz input bandwidth, programmable gain from 0 dB to 6 dB in 1 dB steps, and selectable DDR LVDS or CMOS output interfaces. The device operates from a 3.3 V analog supply and a 1.8 V digital supply, with power scaling linearly with sample rate. The LVDS output supports both standard and low-power modes, providing flexibility for power-constrained systems. Architecturally, the ADS62P44 uses a multi-stage pipelined core with proprietary digital error correction. The internal sample-and-hold preserves aperture jitter below 150 fs RMS, while the differential clock receiver accepts both LVPECL and LVDS levels. The output data is presented DDR (double data rate) on LVDS lanes or as parallel CMOS words, enabling direct connection to FPGAs and ASICs without external deserialization logic. Typical applications include wireless base-station receivers, software-defined radio (SDR) platforms, radar and lidar signal processing, medical imaging front ends, and high-speed data acquisition systems. Designers should ensure the analog inputs are AC- or DC-coupled with proper 50-ohm terminations, and that the clock source has sub-ps RMS jitter to preserve SNR at high input frequencies. The exposed thermal pad must be soldered to a sufficient ground plane for rated performance.

طلب عرض سعر اتصل بنا

الفئات الفرعية

المنتجات (39,000+)

ADS6144IRHBR - 14-Bit 105MSPS Low-Power ADC | Texas Instruments

ADS6145IRHB25 - 14-bit 125MSPS Low-Power ADC | Texas Instruments

ADS6148IRGZ25 - 14-Bit 250 MSPS ADC, DDR LVDS | Texas Instruments

ADS6149IRGZ25 - 14-Bit 250MSPS Low-Power ADC | Texas Instruments

ADS61B23 - 12-Bit 80MSPS ADC, Buffered Inputs | TI

ADS61B23IRHB25 - 12-Bit 80MSPS ADC, Buffered Diff Input | TI

ADS61B29IRGZ25 - 12-Bit 250MSPS Buffered ADC | Texas Instruments

ADS61B49IRGZ25 - 14-Bit 250MSPS Buffered ADC | Texas Instruments

ADS6223IRGZR - Dual 12-bit 80MSPS ADC, Serial LVDS | TI

ADS6224IRGZ25 - Dual 12-Bit 105MSPS ADC LVDS | Texas Instruments

ADS6224IRGZR - 12-bit 105MSPS Dual ADC LVDS | Texas Instruments

ADS6225IRGZR - Dual 12-Bit 125MSPS ADC, Serial LVDS | TI

ADS6242IRGZR - 14-Bit, 65MSPS Dual-Channel LVDS ADC | Texas Instruments

ADS6243IRGZR - Dual 14-Bit 80MSPS ADC w/ LVDS | Texas Instruments

ADS6244IRGZ25 - Dual 14-Bit 105MSPS Serial LVDS ADC | Texas Instruments

ADS62C17IRGC25 - Dual 11-Bit 200MSPS ADC | Texas Instruments

ADS62C17IRGCR - Dual 11-Bit 200MSPS ADC | Texas Instruments

ADS62P15IRGC25 - Dual 11-Bit 125MSPS ADC | Texas Instruments

ADS62P22IRGC25 - Dual 12-Bit 65MSPS ADC | Texas Instruments

ADS62P23IRGC25 - Dual 12-bit 80MSPS ADC, DDR LVDS/CMOS | TI

ADS62P25IRGC25 - Dual 12-Bit 125 MSPS ADC, 64-VQFN | Texas Instruments

ADS62P28IRGC25 - Dual 12-Bit 210-MSPS ADC with DDR LVDS/CMOS | TI

ADS62P42IRGC25 - Dual 14-bit 65MSPS ADC, LVDS/CMOS | Texas Instruments

ADS62P44IRGC25 - Dual 14-bit 105MSPS ADC, LVDS/CMOS | TI