الدوائر المتكاملة

THS4505DR

THS4505DR - Wideband Fully Differential Amplifier | Texas Instruments

The Texas Instruments THS4505DR is a wideband, low-distortion fully differential amplifier designed for high-linearity signal-chain applications, packaged in an 8-pin SOIC (D) package. The device provides one differential amplifier circuit, supports 12-bit operation through 40 MHz according to the manufacturer, and operates across a -40°C to +85°C temperature range. Its fully differential architecture is intended for ADC and DAC interface, instrumentation, and communications signal-chain designs where balanced signal handling improves common-mode rejection and reduces even-order distortion. A fully differential amplifier is a voltage-feedback amplifier that accepts differential inputs and produces a balanced differential output. This category belongs to the broader operational-amplifier hierarchy, where it serves as a precision analog signal-conditioning function between sensors, converters, and communication links. By keeping the signal differential throughout the chain, the THS4505DR can simplify interfacing to balanced ADC front ends while preserving signal integrity at wide bandwidth. The principal feature of the THS4505 is its combination of wide bandwidth, low distortion, and high linearity. Texas Instruments describes the THS4504 and THS4505 as setting new performance standards for fully differential amplifiers, with the THS4505 option omitting the power-down capability found in the THS4504 family. The R suffix identifies the tape-and-reel ordering configuration, while D identifies the 8-pin SOIC package. The R suffix identifies the reel configuration and is consistent with the 8-pin SOIC package. Typical uses include driving high-speed data converters, receiving balanced signals from sensors, amplifying communications-channel outputs, and building low-distortion differential stages for test equipment. Differential operation also makes the device useful where signal symmetry and rejection of common-mode disturbances are important, although final performance still depends on resistor matching, supply configuration, layout symmetry, and the signal bandwidth. In a practical circuit, the THS4505DR is normally placed close to the converter or source. Input and feedback networks should be laid out symmetrically, and decoupling capacitors should connect to the device power pins with minimal loop area. Designers should preserve the amplifier’s specified common-mode and output-range conditions and verify gain, output swing, and stability against the intended load rather than assuming that the wideband headline specification alone guarantees system-level fidelity. This page combines the manufacturer’s product information, exact ordering information, distributor records, and practical engineering guidance. It is intended to help engineers evaluate THS4505DR for wideband differential signal conditioning while distinguishing documented device facts from parameters that still require confirmation from the current manufacturer datasheet.

طلب عرض سعر اتصل بنا

THS4522IPWR

THS4522 - 95MHz Low Power Dual FDA | Texas Instruments

The Texas Instruments THS4522 is a very low-power, dual-channel, fully differential amplifier (FDA) with rail-to-rail output and an input common-mode range that includes the negative rail. It operates from a single 2.5V to 5.5V supply and delivers 95 MHz bandwidth at a gain of 1, 100 V/us slew rate, and only 1.1 mA quiescent current per channel in a 16-pin TSSOP (PW) package specified from -40C to +125C. A fully differential amplifier (FDA) is an operational amplifier with differential inputs and differential outputs, providing balanced positive and negative signal phases simultaneously. FDAs are essential for driving high-performance ADCs because balanced signaling improves common-mode rejection and suppresses even-order harmonics. As a subset of operational amplifiers within analog signal processing, FDAs enable precise amplification, filtering, and level shifting in data converter front-end circuits. Key features include very low input voltage noise of 4.6 nV/rtHz, low distortion of -110 dBc at 1 MHz, and 55 mA output current. A power-down pin reduces quiescent current to 0.5 uA, and the rail-to-rail output maximizes dynamic range in single-supply systems. Negative rail input capability simplifies interfacing with ground-referenced sensors. The THS4522 uses a complementary bipolar process with a precision input stage, achieving 0.5 mV offset voltage and a 95 MHz gain bandwidth product. Full specification across the industrial temperature range ensures reliable operation in harsh environments, while the dual-channel TSSOP-16 configuration saves board space in multi-channel systems. Typical applications include driving high-speed ADCs in medical imaging, industrial process control, and test and measurement equipment. Low power consumption makes it suitable for portable battery-powered instruments, and rail-to-rail output with negative-rail input enables single-supply sensor interfaces. When designing with the THS4522, decouple supplies with 0.1 uF and 10 uF capacitors close to the VCC and VEE pins, use precision low-TCR feedback resistors to maintain gain accuracy, and bypass the VOCM pin to ground for optimal output common-mode control.

طلب عرض سعر اتصل بنا

THS4531A

THS4531A - Ultra-Low-Power Fully Differential Amplifier | TI

The THS4531A from Texas Instruments is an ultra-low-power, fully differential amplifier with rail-to-rail output and an input common-mode range that extends below the negative rail. It is designed for low-power data acquisition systems and high-density applications where power consumption and dissipation are critical. The device operates from a single supply of 2.5V to 5.5V or dual supplies of ±1.25V to ±2.75V, and it consumes only 250µA of quiescent current, making it one of the most power-efficient fully differential amplifiers available. A fully differential amplifier (FDA) is an operational amplifier with differential inputs and differential outputs, providing both the signal and its complement. This architecture inherently rejects common-mode noise and even-order harmonics, making it ideal for driving high-performance ADCs, transmitting signals over long lines, and conditioning sensor outputs. In the signal chain hierarchy, an FDA is a type of amplifier IC, which falls under analog integrated circuits, essential for precision analog signal processing. Key features of the THS4531A include a bandwidth of 36MHz at gain of 1, a slew rate of 200V/µs, and a low input voltage noise of 10nV/√Hz. The device also offers a high open-loop gain of 100dB and a common-mode rejection ratio (CMRR) of 100dB. Its rail-to-rail output stage maximizes dynamic range, and the input common-mode range below the negative rail allows direct interfacing with ground-referenced sensors in single-supply systems. The THS4531A uses a complementary bipolar process and a precision laser-trimmed input stage, ensuring low offset voltage (typically 100µV) and low drift. The device is stable with capacitive loads up to 100pF, and its internal common-mode feedback loop maintains output common-mode voltage at the desired level, simplifying ADC interface design. Typical applications include driving SAR and delta-sigma ADCs, low-power battery-operated instrumentation, portable medical devices, and single-ended to differential conversion for high-speed data acquisition. The device is also suitable for general-purpose differential signal conditioning in industrial and automotive systems. When designing with the THS4531A, ensure proper power supply decoupling with 0.1µF capacitors close to the supply pins. The output common-mode voltage can be set via the VOCM pin, and the feedback network must be balanced to maintain optimal performance.

طلب عرض سعر اتصل بنا

THS4531ID

THS4531ID - Ultra-Low-Power Differential Amplifier | TI

Texas Instruments THS4531ID is an ultra-low-power, fully differential operational amplifier with a supply current of 0.25 mA, a gain-bandwidth product of 36 MHz, and an 8-pin SOIC package. Its input common-mode range extends below the negative supply rail, while its output stage supports rail-to-rail operation. These characteristics suit compact, power-sensitive data-acquisition and signal-conditioning systems in which channel density, common-mode range, and low power dissipation are important. A fully differential amplifier is an operational-amplifier configuration that processes a pair of input signals and produces a differential output. This amplifier category belongs to the broader operational amplifier, analog signal IC, and power management hierarchy. Compared with two independent single-ended amplifiers, a fully differential device can simplify balanced ADC drive, suppress common-mode noise, and maintain signal integrity in systems where both signal polarities carry information. The THS4531ID combines a 0.25 mA supply-current specification with a 36 MHz gain-bandwidth product, allowing closed-loop operation at relatively high signal frequencies without placing the device in a high-power class. Its input common-mode range below the negative rail allows signals to approach or extend beneath ground, which is useful in battery-powered, offset, and sensor-interface systems. Rail-to-rail output operation provides additional output-voltage range when the required signal levels lie near the supply limits. Texas Instruments describes the device as an ultra-low-power, rail-to-rail-output, fully differential amplifier with accurate output common-mode control. The VOCM architecture is important in ADC front ends because it permits the output common-mode voltage to be adjusted independently of the differential input. According to the THS4531 manufacturer datasheet, that control supports direct-coupled operation when driving analog-to-digital converters, including converters whose input common-mode range is not centered at mid-supply. Typical applications include low-power differential ADC front ends, sensor signal conditioning, balanced audio and communication paths, medical acquisition modules, and high-density instrumentation. In each case, the device's 0.25 mA supply current reduces the power burden associated with continuously powered analog channels, while the 36 MHz gain-bandwidth product supports higher-bandwidth closed-loop configurations. The input range below the negative rail is especially useful for signals that include a deliberate DC offset or originate from sensors operated below ground. The principal design consideration is the relationship between gain, bandwidth, output common-mode voltage, and stability. Feedback resistance, compensation settings, and external capacitor choices must follow the manufacturer's recommended application circuit. Board designers should also keep the differential input and feedback paths compact and symmetrical to minimize conversion of common-mode noise into differential error. This product page combines the manufacturer's core specifications with application guidance, package information, practical design notes, and an evidence-based drop-in comparison. It also helps engineers distinguish the SOIC-8 THS4531ID from other THS4531 package and revision options before committing to a PCB footprint.

طلب عرض سعر اتصل بنا

THS4532

THS4532 - Dual 0.25mA RRO Fully-Differential Amplifier | TI

The THS4532 is a dual, ultra-low-power, rail-to-rail output (RRO) fully-differential amplifier from Texas Instruments, designed for low-power data acquisition systems and high-density applications where power consumption and dissipation are critical. It operates over a supply range of 2.5V to 5.5V and draws only 250µA per channel, making it ideal for battery-powered and portable instrumentation. The device features an input common-mode range that extends below the negative rail, enabling single-supply operation with ground-referenced inputs. The THS4532 is available in a 16-pin TSSOP package (PW) and is characterized for operation over the extended industrial temperature range of -40°C to +125°C. A fully-differential amplifier (FDA) is an operational amplifier with differential inputs and differential outputs, providing both the signal and its complement. This architecture inherently rejects common-mode noise and even-order harmonics, making FDAs essential in high-resolution ADC driving, balanced signal transmission, and precision analog front-ends. The THS4532 belongs to the class of low-power FDAs, which are a subset of differential amplifiers, which in turn fall under the broader category of operational amplifiers and linear integrated circuits. Its rail-to-rail output stage maximizes dynamic range in low-voltage systems, while the input common-mode range below the negative rail simplifies single-supply designs. Key features of the THS4532 include ultra-low power consumption of 0.25mA per channel, rail-to-rail output swing, and an input common-mode range that includes the negative rail. The device also offers a wide supply range of 2.5V to 5.5V, making it compatible with 3.3V and 5V systems. The THS4532 is fully specified for operation over -40°C to +125°C, ensuring reliable performance in industrial environments. Its low power and small footprint make it suitable for high-density multichannel data acquisition systems. From a technical perspective, the THS4532 uses a precision CMOS architecture that achieves low offset and drift while maintaining ultra-low quiescent current. The differential output stage provides a balanced signal that can directly drive high-resolution SAR ADCs, such as the ADS8887, without the need for an external transformer. The device's common-mode feedback loop allows the user to set the output common-mode voltage independently, which is critical for matching the ADC's input range. The THS4532 also features internal compensation, simplifying the external component count. Typical applications include driving high-resolution ADCs in portable medical devices, battery-powered industrial sensors, and low-power audio processing. Its low power consumption extends battery life in wearable monitors and wireless sensor nodes. The THS4532 is also used in single-ended to differential conversion for precision measurement systems, where its low noise and high linearity preserve signal integrity. When designing with the THS4532, ensure proper power supply decoupling with 0.1µF capacitors close to the V+ and V- pins. The output common-mode voltage should be set to the ADC's reference midpoint to maximize dynamic range. For optimal noise performance, use metal-film resistors in the feedback network and keep the feedback paths short.

طلب عرض سعر اتصل بنا

THS4551IRGTR

THS4551IRGTR - 150MHz Fully Diff Amp | Texas Instruments

The Texas Instruments THS4551IRGTR is a low-noise, precision, 150 MHz fully differential amplifier (FDA) housed in a 16-pin VQFN (RGT) package with exposed thermal pad. It offers a -3 dB bandwidth of 150 MHz (G = 1 V/V), 1.5 nV/√Hz input voltage noise density, and rail-to-rail output swing that simplifies ADC driver designs in space-constrained systems. A fully differential amplifier is an op-amp topology that converts a single-ended or differential input signal into a balanced differential output centered around a settable common-mode voltage. FDAs sit in the signal chain between sensor/transducer signal conditioning and high-speed, high-resolution analog-to-digital converters (ADCs). They reject common-mode noise and even-order harmonics, drive differential ADCs cleanly, and enable DC-coupled paths through SAR or delta-sigma converters - placing them in the broader hierarchy of operational amplifier -> amplifier IC -> analog signal chain -> semiconductor. Key features include 150 MHz small-signal bandwidth, 50 V/µs slew rate, 1.5 nV/√Hz voltage noise, 100 dB DC open-loop gain, and a 2.7 V to 5.4 V single-supply operating range. The integrated VOCM pin sets the output common-mode voltage independently of the input, simplifying interface to ADCs with 0.5 V to 2.5 V common-mode requirements. Internal common-mode feedback preserves output balance across frequency, eliminating the need for precision matched external resistors. Architecturally the device combines a precision input stage with a class-AB output stage capable of driving 2 VPP into 200 Ω differential loads (typical for 16-bit ADCs). The 1.5 nV/√Hz noise floor makes it suitable for 16-bit ADC reference designs, and the wide bandwidth handles 18-bit SAR converters sampling above 1 MSPS. Typical applications include 16-bit to 20-bit ADC drivers, precision instrumentation front-ends, transducer signal chains, and active filters. The single-ended-to-differential conversion is ideal for driving AD7768, ADS131A04, and similar precision SAR converters in measurement equipment. When designing with this part, use a feedback resistor network that sets the desired gain and a VOCM bypass capacitor of 0.1 µF for noise decoupling. Verify output common-mode voltage tracks VOCM input over frequency to avoid ADC distortion. This page synthesizes distributor pricing, drop-in alternatives, and application notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

THS4551IRGTT

THS4551IRGTT - 150MHz Low-Noise Fully Diff Amplifier | Texas Instruments

The Texas Instruments THS4551IRGTT is a low-noise, precision, 150-MHz, fully differential amplifier (FDA) housed in a 16-pin VQFN (RGT) package with exposed thermal pad, optimized for driving high-speed, differential-input ADCs in industrial, instrumentation, and communications signal chains. It delivers 150 MHz of unity-gain bandwidth, 50 ns settling time to 0.1%, 200 V/us slew rate, and -100 dB low total harmonic distortion plus noise (THD+N) at 2 VPP and 100 kHz, while operating from a single 2.7 V to 5.4 V supply with rail-to-rail output swing. Its wideband architecture combines precision DC trim with a low input-referred voltage noise of 3.3 nV/sqrt(Hz) and an integrated output common-mode control loop that tightly regulates the output common-mode voltage set by the VOCM pin, eliminating the need for external precision resistor matching on the feedback network. A fully differential amplifier (FDA) is a specialized op-amp topology that converts a single-ended or differential input signal into a balanced differential output, where each output swings symmetrically around a programmable common-mode voltage. FDAs sit at the boundary between the analog front end (sensor/transducer) and the differential input stage of a high-speed ADC, and they are essential for maximizing spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) in modern data-acquisition chains. Compared to a single-ended op-amp, an FDA inherently rejects common-mode noise from the analog supply, suppresses even-order harmonics, and directly interfaces with differential ADCs without lossy transformer coupling. Key features of the THS4551IRGTT include a wide 2.7 V to 5.4 V single-supply operating range, a flexible output common-mode control input (VOCM) that supports direct DC coupling to the ADC common-mode voltage, low input bias current, integrated shutdown bias current control, and 8 kV HBM ESD protection. The device is characterized for operation across the industrial -40C to +125C temperature range and is fabricated in TI's proprietary high-speed complementary BiCMOS process. The 3x3 mm VQFN package exposes the thermal pad to a top-side copper pour, allowing continuous full-bandwidth operation at 5 V without exceeding the 175C junction limit. Typical applications of the THS4551IRGTT include driving successive-approximation register (SAR) and delta-sigma ADCs in industrial process control, test and measurement data acquisition, high-density medical imaging front ends, and broadband communications baseband signal chains. Its low noise and high linearity also make it suitable for active balun replacement, audio line drivers, and I/Q modulator interface networks in software-defined radio (SDR) systems. When designing with this device, place the input and feedback network components as close to the IC pins as possible and follow the datasheet differential-input filter recommendations to preserve bandwidth and maximize SFDR; a small mismatch in the feedback resistors will degrade the common-mode rejection ratio (CMRR) at the frequency of interest, so 0.1% tolerance parts are recommended. This page synthesizes distributor pricing, parametric drop-in alternatives, application-specific design notes, and pinout guidance not consolidated on the manufacturer datasheet front page.

طلب عرض سعر اتصل بنا

THS4601ID

THS4601ID - 180MHz FET-Input Op Amp | Texas Instruments

Texas Instruments THS4601ID is a wideband, FET-input operational amplifier with 180 MHz gain-bandwidth product, 100 V/µs slew rate, and one amplifier circuit in an 8-pin SOIC package. It operates from ±5 V to ±15 V and is designed for high-impedance signal paths requiring broad bandwidth, fast slew rate, and low input-bias current. A FET-input operational amplifier is a voltage-amplifier IC whose input stage uses field-effect transistors rather than bipolar input transistors. This type of input stage supports high input impedance and low bias current while operating in the voltage-amplifier hierarchy used for instrumentation, analog signal conditioning, buffers, and active filters. The THS4601ID is a single-channel general-purpose amplifier intended to preserve fast signal transitions without adding excessive input loading. Key electrical characteristics include 180 MHz gain-bandwidth product, 100 V/µs slew rate, and approximately 100 pA input-bias current. Its ±5 V to ±15 V supply range supports dual-rail analog systems operating at 10 V or 30 V total voltage. These characteristics make the device suitable for high-speed buffer stages, low-level sensor interfaces, communications equipment, and test-and-measurement signal chains. The combination of wide bandwidth and high slew rate allows the amplifier to process signals with short rise and fall times. At low signal amplitudes, bandwidth behavior is primarily governed by the 180 MHz gain-bandwidth product; at larger output transitions, slew rate becomes the principal limiting factor. Because it is a FET-input amplifier, the input stage can avoid the higher bias currents characteristic of many bipolar-input op amps while retaining wideband operation. Typical uses include instrumentation amplifiers, active filters, analog measurement front ends, communication receivers, data-acquisition channels, and impedance buffers. The SOIC-8 package supports conventional surface-mount assembly and is useful when a high-speed amplifier must be placed close to the source or destination circuitry. The single-amplifier configuration also makes the device appropriate for designs that require one independent high-speed channel per package. Layout is especially important because wideband amplifiers can amplify high-frequency noise, ringing, and supply ripple. Place input, output, and decoupling connections with short traces, maintain symmetric routing where practical, and use solid ground-plane return paths. Verify stability, output swing, settling behavior, and power-supply sequencing in the final circuit rather than assuming that nominal bandwidth alone guarantees system performance. This page combines manufacturer product information, distributor availability indicators, same-package substitution details, application guidance, and practical design notes. It is structured to support direct part selection, PCB footprint confirmation, and drop-in replacement assessment for engineers evaluating the THS4601ID.

طلب عرض سعر اتصل بنا

THS4631D

THS4631D - 210MHz High-Speed FET Op Amp | Texas Instruments

Texas Instruments THS4631D is a high-speed, wideband, FET-input operational amplifier designed for wideband operation, high input impedance, and high-power-supply applications. The device provides a 210 MHz gain-bandwidth product, a 1000 V/µs slew rate, and 100 pA input bias current, with operation from a ±15 V supply. It is available in the 8-pin SOIC D package, making it suitable for high-speed instrumentation, transimpedance amplification, wideband signal conditioning, and communications signal chains. A high-speed operational amplifier is an analog integrated circuit that provides voltage gain while preserving the timing and signal characteristics of high-frequency waveforms. The THS4631D combines a FET-input architecture with wideband feedback operation, allowing it to handle low-level input signals while maintaining large output signal swing. Its combination of high bandwidth, fast slew rate, low input current, and low noise is particularly useful when the system must amplify signals quickly and accurately. Key characteristics include a 210 MHz gain-bandwidth product, 1000 V/µs slew rate, and 100 pA input bias current. The wide supply-voltage capability supports high-voltage analog systems where the signal excursion must remain large. The amplifier is intended for simultaneous wideband transimpedance gain and large output signal swing, while its low current and voltage noise help preserve signal-to-noise ratio when processing extremely low-level inputs. THS4631D applications include photodiode and optical receiver front ends, high-speed data-acquisition systems, instrumentation, communications equipment, and precision analog signal-conditioning circuits. The fast slew rate supports short settling times and good harmonic-distortion performance at high frequencies. The low input bias current is particularly valuable when the source impedance is high or when leakage errors would otherwise dominate the measurement. For PCB layout, keep input, feedback, and output paths short and minimize parasitic capacitance. Decoupling capacitors should be placed close to the supply pins, and the feedback network should use low-inductance routing. Because high-speed amplifiers can amplify small parasitic signals, grounding, probe grounding, and controlled return paths are as important as nominal gain configuration. Always verify the package pinout and operating limits against the manufacturer datasheet before substituting an equivalent device. This page consolidates the verified manufacturer information, distributor references, pricing information, package details, and engineering guidance for engineers evaluating the THS4631D in high-speed analog systems.

طلب عرض سعر اتصل بنا

THS6042CD

THS6042CD - 350mA ±12V ADSL CPE Driver | Texas Instruments

The Texas Instruments THS6042CD is a high-speed, high-output-current operational amplifier and ADSL CPE line driver delivering 350 mA from a ±12 V supply in an 8-pin SOIC package. It is designed for analog signal conditioning, line-driver, and communications-interface circuits where low distortion, adequate slew capability, and source-current capacity are important. An operational amplifier is an active analog signal-conditioning device that uses high open-loop gain to amplify voltage differences. Within the broader semiconductor hierarchy, the THS6042CD belongs to the operational-amplifier family, which falls under amplifier ICs and analog signal-chain components. Its current-output capability distinguishes it from conventional low-current voltage-feedback amplifiers used only around precision analog signals. The verified product information identifies a 350 mA output-current rating, a ±12 V operating supply, and an 8-SOIC package. The Mouser listing also classifies the device as a high-speed operational amplifier for 350 mA ±12 V ADSL CPE line-driver applications. These characteristics make it relevant to designs requiring a signal amplifier to drive a terminated line, transformer, or communications interface rather than merely provide voltage gain. The THS6042CD combines an amplifier core with line-driving capability in a compact surface-mount package. Because it dissipates power while operating, the total supply voltage, output swing, load, and ambient temperature must be considered together. Its SOIC-8 format simplifies assembly and allows reuse of conventional eight-pin analog layouts, but exposed-pad thermal performance is not available from the supplied data. Typical applications include ADSL customer-premises-equipment line interfaces, communications transmitters, industrial signal conditioning, and low-frequency power-driver stages. In each case, the 350 mA current capability offers more drive than a standard small-signal amplifier, while the ±12 V supply supports bipolar output swing around ground. Designers should verify the required output swing, load impedance, stability, slew rate, bandwidth, and thermal margin against the manufacturer datasheet before production release. Cable or transformer loading, DC offset, and excessive capacitive loading can materially affect distortion and stability, particularly when using a high-current amplifier outside its most favorable operating region. This page consolidates the verified distributor listings, package information, current sourcing reference, and same-family replacement findings. It also distinguishes documented facts from specifications requiring confirmation, providing practical context for evaluating the THS6042CD in ADSL CPE and other high-current analog-driver designs.

طلب عرض سعر اتصل بنا

THS6042ID

THS6042ID - 350mA ADSL CPE Line Driver | Texas Instruments

The Texas Instruments THS6042ID is a 350 mA high-speed DSL line driver designed for ADSL and power-line communication equipment, operating from a ±12 V supply in an 8-pin SOIC package. It is intended to transmit signals from the remote terminal toward the central office while providing high output-current capability for transformer-coupled lines. A DSL line driver is a specialized interface IC that conditions high-frequency signals for transmission over copper, telephone, or power-line networks. The THS6042 belongs to the broader line-driver and interface-IC hierarchy, where its role is to combine high-speed signal handling with enough output drive to overcome line impedance and losses. Its dual-driver configuration suits equipment requiring more than one transmitted signal channel. Key characteristics include 350 mA output drive, operation from dual ±12 V supplies, and low distortion of -79 dBc when driving a 100 ohm load with a 2 Vpp signal. The device draws only 8.2 mA of supply current per channel. Its noninverting current noise is 2.1 pA/Hz, and the family supports full-rate ADSL and G.Lite service while remaining compatible with a 1:1 transformer ratio. The architecture is tailored for low-voltage, high-speed differential line transmission. A high 43 Vpp output swing provides useful dynamic range for overcoming attenuation in subscriber-line networks, while the current capability allows direct coupling to suitable external networks and transformers. Low noise and distortion help preserve signal integrity in the transmit path, particularly when small analog or mixed-signal information is represented by a high-speed line waveform. Typical applications include ADSL customer-premises equipment, central-office line-interface equipment, PLC line drivers, telephone-line termination circuits, and other high-speed copper-pair transmitters. The THS6042 is especially relevant where a ±12 V rail is already available and the designer needs a dedicated line-driver function rather than a general-purpose operational amplifier. Design attention should focus on supply decoupling, transformer or termination-network selection, controlled board layout, and thermal behavior at maximum output drive. Keep high-current return paths short and place input and output components to minimize parasitic feedback. Because the device dissipates power in proportion to output voltage and current, verify worst-case load conditions and provide adequate copper area around the SOIC pins. This page organizes the key electrical characteristics, application guidance, package details, and qualified replacement information into an engineering-focused reference for selecting and implementing the THS6042ID in high-speed DSL line-interface designs.

طلب عرض سعر اتصل بنا

THS6043CD

THS6043CD - 350mA ±12V ADSL Line Driver | Texas Instruments

The Texas Instruments THS6043CD is a dual, low-power ADSL CPE line driver rated for 350 mA per channel and operation from dual ±12 V supplies. The device provides two line-driver channels and two shutdown-control inputs in a 14-pin SOIC package. Its design targets full-rate ADSL and G.Lite customer-premises equipment connected to 1:1-ratio isolation transformers. An ADSL line driver is a high-current differential output amplifier used at the customer-premises side of a broadband access interface. It sits between the codec or transceiver and the line-transformer network, providing sufficient current and voltage swing to drive a copper pair through the transformer while limiting bandwidth and noise that could disturb downstream channels. In the electronics hierarchy, the THS6043CD is a high-speed interface IC and line-driver circuit rather than a general-purpose precision amplifier. The THS6043CD supports 120 MHz device bandwidth and provides differential output swing above 40 Vpp into a 200-ohm load with ±12 V supplies. Its noninverting current-noise density is approximately 2.1 pA/√Hz, helping limit broadband noise coupled through the hybrid into the downstream channel. A 43-Vpp differential output swing is identified for the THS6043 family at a 200-ohm load, giving the line driver useful headroom for transformer and copper-pair interfaces. A dedicated shutdown function reduces quiescent current to approximately 300 µA per channel when the circuit is inactive. This low-power behavior is useful in CPE equipment that must reduce consumption between active communication periods. The dual-channel organization also allows one device to serve both directions of a line interface, reducing component count and helping keep transformer-driver routing symmetrical. The THS6043CD is suitable for full-rate ADSL and G.Lite line cards, splitter or filter modules, central-office line-interface equipment, and test equipment that emulates subscriber-line conditions. Its 14-pin SOIC format supports conventional PCB assembly, while the high output-current capability is the defining consideration when selecting a line driver for transformer-coupled DSL interfaces. Designers should verify external transformer ratios, load impedance, supply sequencing, and total channel dissipation before layout. Keep output-current paths short, provide adequate input and output bypassing, and confirm that the selected SOIC copper area limits junction-temperature rise. The shutdown pins should be controlled only after the downstream interface is in a safe state. This product page combines the THS6043CD electrical identity, verified package information, drop-in alternatives, interface applications, and practical implementation guidance to support faster component selection and PCB design.

طلب عرض سعر اتصل بنا

THS6043ID

THS6043ID - 350mA ±12V ADSL CPE Line Driver | TI

Texas Instruments THS6043ID is a high-speed dual operational amplifier configured as a 350 mA ADSL CPE and PLC line driver with shutdown, housed in a 14-pin SOIC package. The device operates from ±12 V rails, supports full-rate ADSL and G.Lite applications, and is compatible with a 1:1 transformer ratio. According to the manufacturer product information, the THS6043 can operate from ±12 V while drawing 8.2 mA of supply current per channel. An operational amplifier is an amplifier IC whose high open-loop gain and feedback configuration amplify voltage differences between its inputs. The THS6043 belongs to the operational-amplifier hierarchy and is specialized as a high-speed line driver within the broader amplifier IC category. In ADSL and power-line communication equipment, a line driver strengthens signals before they pass through a transformer coupling network and onto a copper line. The most prominent characteristics are its 350 mA output-drive capability, ±12 V dual-supply operation, integrated shutdown function, and suitability for full-rate ADSL and G.Lite service. A stated distortion figure of 79 dBc is reported when driving a 100 Ω load at 2 V peak-to-peak. Its low noninverting current noise of 2.1 pA/√Hz is intended to reduce noise feedback through the hybrid into the downstream communication channel. The THS6043 uses a high-speed operational-amplifier core with current-capable outputs suited to transformer-coupled line interfaces. Its dual-channel arrangement allows one package to serve the transmit path of an ADSL or PLC CPE design. Because the driver dissipates power as voltage and current are applied to the line load, adequate supply-decoupling layout and thermal planning remain important even though the quoted 8.2 mA supply current per channel is much lower than the 350 mA output-current capability. Typical applications include ADSL customer-premises equipment, G.Lite-compatible access terminals, PLC line interfaces, remote-terminal transmit drivers, and central-office line-driving stages. The 14-pin SOIC package is suitable for conventional surface-mount assembly and copper-based thermal spreading, subject to the manufacturer's layout and maximum electrical ratings. Designers should verify the exact pin configuration, recommended external network, transformer ratio, allowable output swing, and shutdown logic in the manufacturer datasheet before layout release. Particular care is required when driving low-impedance lines because excessive output current, voltage overshoot, or incorrect transformer coupling can violate device ratings even when nominal ADSL operation is maintained. This page consolidates verified manufacturer and distributor information, distinguishes available evidence from unverified parameters, and provides application guidance, comparison limitations, and drop-in-replacement criteria that are not presented as a substitute for the original THS6043 datasheet.

طلب عرض سعر اتصل بنا

THS6052CD

THS6052CD - 175mA ±12V ADSL CPE Line Driver | TI

The Texas Instruments THS6052CD is a 175 mA, ±12 V ADSL CPE and PLC line driver integrated circuit in an 8-SOIC package. It is designed for full-rate ADSL and G.Lite applications, with a noninverting current-noise density of 2.7 pA/√Hz and a wide supply-voltage range suitable for dual-polarity line-driver circuits. The device provides two driver outputs, supports operation from a 1:1 transformer ratio, and is intended for customer-premises equipment, splitters, and other high-current telephone-line interface applications. An ADSL line driver is a specialized interface amplifier that converts a low-level transmit signal into the voltage and current levels required by a copper telephone line. The THS6052CD belongs to the interface-IC and line-driver hierarchy, combining signal conditioning with the drive capability needed to overcome line attenuation and transformer losses. Its ±12 V operating capability also makes it suitable for bipolar line interfaces where a single positive supply would not provide adequate output swing. The main feature of the THS6052CD is its combination of high output current, low current noise, and a wide supply range. The 175 mA output-current capability provides margin for driving the line through transformer windings and termination networks. The 2.7 pA/√Hz noninverting current-noise specification helps preserve signal integrity when the driver is used in sensitive transmit paths. A wide operating supply range supports both conventional ADSL equipment and power-line-related line-driver circuits. The THS6052CD uses an 8-SOIC package, which is a surface-mount package in the SOIC family. The device is specified for 0 to 70 °C operation in the distributor data supplied for the THS6052CD. Its architecture is intended for high-current line driving rather than general-purpose low-power signal conditioning, so the external transformer, termination, protection, and biasing network must be designed around the specified output-current and supply-voltage limits. Typical applications include ADSL customer-premises equipment, G.Lite modems, DSL line-interface networks, telephone-line splitters, and PLC-style line-driver interfaces. In these systems, the THS6052CD is placed between the upstream transmit signal path and the line transformer, with local feedback used to establish the required drive level and bandwidth. The device can reduce the number of external drive components when its current capability and noise performance match the transformer and network requirements. Designers should pay particular attention to supply bypassing, transformer selection, output-current margin, and protection against transient events on the telephone line. The SOIC package also requires careful thermal assessment when operating continuously near the 175 mA output-current capability. The available verified information does not provide a complete pinout table, detailed timing characteristics, or a complete set of quantitative electrical limits, so those values are identified in the specification fields as data needed for final design sign-off. This page combines the verified Texas Instruments product identity, distributor package and pricing information, relevant source links, and engineering-oriented selection guidance. It is intended to help engineers identify whether the THS6052CD matches the required ADSL line-driver application before downloading the official manufacturer datasheet and completing detailed circuit validation.

طلب عرض سعر اتصل بنا

THS6053CD

THS6053CD - 175mA ADSL Line Driver | Texas Instruments

Texas Instruments THS6053CD is a high-speed current-output driver integrated circuit designed for full-rate ADSL and G.Lite customer-premises equipment, power-line communication networks, and other line-driver applications. The device provides 175 mA peak output current, supports operation from dual positive and negative 12 V supplies, and includes a shutdown function. It is packaged in a 14-pin SOIC. An ADSL CPE line driver is a specialized interface-circuit component that converts upstream transmitter signals into high-current, low-distortion drive signals suitable for telephone or power lines. This device belongs to the current-output line-driver class, which sits below high-speed operational amplifiers and above the wider category of interface ICs. Its dual-polarity supply architecture enables symmetrical signal swing around ground, making it suitable for balanced communication links and transformer-coupled line interfaces. The THS6053 offers low noninverting current noise of 2.7 pA/sqrt Hz, helping reduce feedback from the line-driver output into the downstream receive channel. It is intended for full-rate ADSL and G.Lite systems and is compatible with a 1:1 transformer ratio. A shutdown function allows the circuit to enter a controlled low-power state when line-driver operation is not required, making the device useful in continuously powered telecom and networking equipment. The dual current-output architecture is intended to drive external circuitry rather than directly driving a conventional voltage-output load. Because current-mode outputs can exhibit high compliance-voltage requirements, the external network, transformer, and supply headroom must be checked carefully. Noise and distortion performance also depend on the complete signal path, including the external resistor and transformer network, supply bypassing, and PCB grounding. The THS6053CD should therefore be treated as a complete line-interface subcircuit rather than as a general-purpose logic driver. Typical uses include ADSL CPE line interfaces, G.Lite modems, power-line communication equipment, balanced telephone-line transmitters, and other high-speed communications systems requiring bipolar current drive. Its 14-pin SOIC package is suitable for conventional surface-mount assembly and allows routing on both sides of a two-layer PCB. Designers should place input, supply, and output-network components close to the device, use low-inductance bypass capacitors on each supply rail, and maintain a quiet ground return. Verify external resistor values, current compliance, transformer ratio, bandwidth, and thermal conditions before production release. The SOIC package also limits heat dissipation compared with exposed-pad or power packages, making copper area and airflow relevant at sustained maximum output current. This page organizes the confirmed THS6053CD characteristics, sourcing information, application guidance, and verified-source links. Detailed electrical limits, pin assignments, and lifecycle declarations should be checked against the current Texas Instruments product page and manufacturer datasheet before schematic or BOM approval.

طلب عرض سعر اتصل بنا

THS6053ID

THS6053ID - 175mA Dual ADSL Line Driver | Texas Instruments

The Texas Instruments THS6053ID is a dual high-speed DSL line driver designed for ADSL customer-premises-equipment and power-line communications. It provides two output channels, each capable of sourcing 175 mA, and operates from a 5 V to 15 V supply in a 14-pin SOIC package. The device is intended for dual ±12 V operation, with 5.2 mA of supply current per channel and a shutdown function for reducing power consumption when the line driver is not needed. A DSL line driver is an interface integrated circuit that converts a low-voltage logic signal into a high-current, low-voltage differential signal suitable for transmission over a twisted pair. Within the signal-chain hierarchy, the THS6053ID is a line driver within the broader category of interface ICs, bridging digital logic and telephone-line or power-line networks. Its 175 mA output capability provides the current needed to drive a 1:1 ratio isolation transformer and a line termination network. The THS6053ID supports both full-rate ADSL and G.Lite applications. A documented current-noise density of 2.7 pA/√Hz is particularly useful in this environment because it limits the broadband noise coupled into the hybrid and the downstream channel. Wide supply-voltage tolerance permits operation from single-ended rails or from split ±12 V supplies, while the shutdown input supports power-management strategies in multichannel CPE equipment. The device provides two line drivers and no receivers. Its key design consideration is that the line-driver outputs must remain compatible with the external transformer, termination, protection, and filtering network. Output-current headroom and thermal dissipation should be checked against the selected transformer and cable length rather than inferred only from the nominal 175 mA rating. Typical uses include ADSL CPE line interfaces, PLC modems, splitter and filter assemblies, and other high-speed DSL or line-driver subsystems. This page also consolidates verified pricing, same-package alternatives, pin and application guidance, and comparison information that is not presented together in a single manufacturer document.

طلب عرض سعر اتصل بنا

THS6062CD

THS6062CD - 100 MHz Low-Noise ADSL Receiver | Texas Instruments

Texas Instruments THS6062CD is a low-noise, high-speed dual differential receiver designed for ADSL data-communication systems. Its headline specifications are 1.6 nV/√Hz input-voltage noise density, 100 MHz small-signal bandwidth, and a 100 V/µs slew rate. The device is packaged in an 8-pin SOIC and contains two voltage-feedback receiver channels optimized for low-noise, high-speed differential signal handling. A differential receiver is an amplifier that responds to the voltage difference between two input terminals rather than to either input independently. This differential architecture is part of the operational-amplifier hierarchy and is widely used in communications interfaces, analog-to-digital converter drivers, line receivers, and signal-conditioning systems. By rejecting common-mode signals, a differential receiver can preserve small information-bearing signals in noisy environments. The THS6062 is positioned specifically for ADSL receiver front ends, where low noise and wide bandwidth are important because the received signal must retain both signal amplitude and timing information. The THS6062 combines 1.6 nV/√Hz voltage-noise density with a gain bandwidth of 100 MHz. Its typical slew rate is 100 V/µs, and the manufacturer identifies the device as stable for gains of 2 or greater, including inverted operation at gain -1. A typical output-drive current of 90 mA supports demanding line-receiver applications. Its low distortion figures include THD of -72 dBc at 1 MHz and -90 dBc at 1 MHz under the cited operating conditions. The device accepts a wide range of supply voltages, including single 5 V operation and dual ±5 V operation; ±15 V is also identified as a typical operating configuration. Its dual-channel arrangement allows one package to service two differential receiver paths. The combination of differential input handling, high bandwidth, low voltage noise, and high slew rate makes the THS6062 suitable for ADSL line-interface circuitry and other wideband applications requiring accurate signal amplification. Typical uses include ADSL customer-premises equipment, differential ADC input stages, communications transceivers, video and instrumentation front ends, and balanced line receivers. In these systems, the THS6062 can sit between a transformer or balanced line and the codec, ADC, or subsequent signal-processing block. The wide bandwidth supports high-data-rate signals, while the 1.6 nV/√Hz noise density helps preserve low-amplitude information. Designers should preserve the receiver’s low-noise behavior by keeping input and feedback traces short, providing clean ground references, and avoiding unnecessary parasitic capacitance around the pins. The manufacturer’s pin description and typical application circuits should be followed for supply decoupling and gain-setting resistors. The 8-pin SOIC footprint also supports conventional surface-mount assembly, although exposed-pad thermal guidance is not applicable to this package. This page combines manufacturer specifications, verified cross-reference candidates, same-package comparisons, and application-focused design guidance. These resources make it easier to evaluate the THS6062CD for ADSL, communications, instrumentation, and other high-speed differential receiver designs before committing it to a PCB layout.

طلب عرض سعر اتصل بنا

THS6062ID

THS6062ID - 100MHz Dual Differential Receiver | Texas Instruments

The Texas Instruments THS6062ID is a dual differential receiver designed for ADSL data communication systems, combining 100 MHz voltage-feedback bandwidth, a 100 V/us slew rate, and low 1.6 nV/sqrt(Hz) voltage noise in an 8-pin SOIC package. The device contains two high-speed amplifier channels and is designed for stable operation at gains of 2 or greater. A differential receiver is an interface-circuit block that extracts the difference between two input signals while rejecting common-mode voltage and noise. This function is important in communication systems where the wanted signal is small, transmission losses are significant, and unwanted voltage can be shared by both input lines. The THS6062 belongs to the high-speed voltage-feedback amplifier family and is used in interface IC, line-driver, receiver, and signal-conditioning applications. Key characteristics include a 100 MHz -3 dB bandwidth, a typical 100 V/us slew rate, a typical 1.6 nV/sqrt(Hz) input-voltage noise density, and a typical 90 mA output drive. The receiver supports 5 V single-supply operation and dual supplies from -5 V to -15 V, giving designers flexibility for legacy telecom, ADSL, codec, and line-interface equipment. According to the Texas Instruments THS6062 product page, the circuit is stable at gains of 2 (-1) or greater. The low-noise, high-speed architecture is useful where signal fidelity must be preserved across a broad bandwidth. The 100 MHz bandwidth supports high-data-rate communication paths, while the 100 V/us slew rate allows large-amplitude signals to be reproduced with limited slew-related distortion. The listed distortion figures include THD of -72 dBc at 1 MHz and -90 dBc at 1 MHz under the stated measurement conditions. Typical applications include ADSL line-interface circuits, ADSL codec front ends, differential data receivers, communication equipment, and general high-speed signal-conditioning stages. The dual-channel configuration can process two related differential signals or be used in separate receiver channels when appropriate. Because this is a high-speed device, PCB layout, decoupling, return paths, input impedance, and output-load stability require careful attention. When laying out a THS6062ID circuit, keep input and output traces short, provide local supply bypassing, maintain a continuous ground reference, and avoid long stubs or parasitic capacitance on high-impedance nodes. Confirm the intended gain, supply configuration, input common-mode range, output load, and termination against the manufacturer datasheet before releasing production artwork. This page combines verified manufacturer and distributor information with drop-in candidate review, application guidance, and design notes.

طلب عرض سعر اتصل بنا

THS6072CD

THS6072CD - Low-Power ADSL Differential Receiver, 175 MHz | Texas Instruments

The Texas Instruments THS6072CD is a low-power ADSL differential receiver with two channels of high-speed receive amplification, 3.4 mA of quiescent current per channel, 10 nV/√Hz of input voltage noise, and a 175 MHz -3 dB bandwidth, all housed in an 8-pin SOIC (D) package. It targets central-office and remote-terminal ADSL line-card equipment where power budget and signal fidelity both matter. A differential receiver is an interface IC that converts a small differential signal arriving over a twisted pair into a single-ended logic-level output suitable for an ADC, DSP, or codec. Within the broader hierarchy of semiconductor interfaces, the THS6072CD sits in the DSL line-receiver family: line receiver > differential receiver > interface IC > semiconductor. In an ADSL/POTS terminal it is the analog front end that recovers the modulated carrier band before digitization. Key features include the low 3.4 mA per-channel quiescent current, which the manufacturer states cuts receiver power to roughly half that of competing ADSL receivers, making the device well suited to line cards where dozens of channels share one power supply. Input voltage noise of 10 nV/√Hz keeps the receiver's contribution well below the quantization floor of the downstream codec, and total harmonic distortion of -79 dBc at 1 MHz limits intermodulation products in the recovered spectrum. The 175 MHz -3 dB bandwidth provides headroom above the ADSL downstream band. Architecturally the device is a low-noise differential input stage followed by a high-gain, high-speed output stage, with per-channel bias currents scaled so that the total supply draw stays near 6.8 mA for the dual version. Because the part is a receiver rather than a driver, it consumes no significant output drive current and can source only the CMOS-level loads expected of a following converter stage. Typical applications include ADSL central-office line cards, remote terminal units, customer-premises equipment with integrated splitters, and upstream/downstream PONS-over-ADSL style transport gear. Because it is intended for pair-terminated copper lines, common-mode rejection and noise performance matter more than wide output swing. When designing with the THS6072CD, place the input network so the differential pair sees matched impedances and identical trace lengths, and decouple the supply pins locally to keep switching-riser energy from folding into the input stage. Keep the analog path short and do not add extra gain ahead of the receiver, since that degrades the noise figure the part was designed to preserve. This page consolidates distributor availability, same-footdrop alternatives, and practical layout guidance for the THS6072CD that is not reproduced on standard distributor listings.

طلب عرض سعر اتصل بنا

THS6072ID

THS6072ID - 175MHz Low-Power ADSL Receiver | TI

The Texas Instruments THS6072ID is a low-power ADSL differential receiver with 175 MHz bandwidth, 10 nV/√Hz voltage noise, and 3.4 mA per-channel quiescent current, housed in an 8-pin SOIC package. Designed for high-speed differential signal recovery, it targets central-office and remote-terminal ADSL equipment where bandwidth, low distortion, and reduced power consumption are important. An ADSL differential receiver is a voltage-feedback, high-speed analog interface circuit that converts a small differential input signal into a single-ended output suitable for processing by downstream circuitry. In the signal-chain hierarchy, it belongs to the receiver and operational-amplifier family within interface ICs, supporting the broader communications, networking, and data-processing systems used to transport high-frequency digital information over copper lines. Key characteristics include a 175 MHz -3 dB bandwidth, a 10 nV/√Hz voltage-noise density, and very low distortion of -79 dBc at 1 MHz with a 1 kΩ load. The 3.4 mA per-channel quiescent current supports low-power ADSL designs, while the wide bandwidth provides margin for high-speed data and test-and-measurement signal-chain applications. The operating temperature range is -40°C to +85°C, covering industrial-temperature applications. Technically, the THS6072 uses a voltage-feedback receiver architecture optimized for differential operation. Its low noise and low distortion make it suitable for amplifying small signals without adding excessive broadband noise or nonlinear products. Designers should still verify input common-mode range, output swing, supply voltage, gain configuration, stability, and external component requirements against the manufacturer datasheet before finalizing a production circuit. Typical applications include ADSL line-interface equipment, central-office termination electronics, remote-terminal units, high-speed communication receivers, broadband signal-conditioning modules, and instrumentation requiring a wide-band differential input stage. The 8-pin SOIC package also supports conventional PCB assembly, although high-speed layout and clean return paths remain important. The principal design consideration is signal integrity. Keep differential traces short, matched, and continuous over a common ground plane, place input and bypass components close to their pins, and control return currents. Verify that external compensation and gain settings preserve stability at the intended load and signal amplitude. This product page consolidates verified manufacturer and distributor information, supply data, technical characteristics, candidate drop-in alternatives, and practical interface-layout guidance to support faster component selection and PCB design.

طلب عرض سعر اتصل بنا

THS6092CD

THS6092CD - 275mA +12V ADSL Driver | Texas Instruments

The Texas Instruments THS6092CD is a dual high-speed operational amplifier configured as a 2/0 differential line driver for ADSL CPE and DSL applications. It supplies 275 mA of output current, operates from a single +12 V supply, and is packaged in an 8-pin SOIC. The device is intended for driving signals from a remote terminal toward the central office in asymmetrical digital subscriber line systems. An ADSL line driver is a specialized high-speed operational amplifier that delivers large current into a transformer-coupled or balanced line while maintaining low distortion and stable signal integrity. Within the power-management and signal-chain hierarchy, the THS6092 belongs to the operational-amplifier family, with applications in communications, networking, and broadband access equipment. The THS6092 family uses a +12 V supply and provides two output channels per package. According to the Texas Instruments THS6092 product page, the device is a 275 mA ADSL CPE and DSL line driver. Comparison information for the THS6092 identifies a supply current of 7.3 mA per channel and total harmonic distortion of -72 dBc while driving a 25-ohm load at 2 V peak-to-peak. These characteristics make the device appropriate for high-speed line-driving stages that require useful output swing, low distortion, and controlled supply consumption. The dual-channel architecture reduces the component count in broadband equipment by combining two line-driver channels in one package. Its 8-pin SOIC format supports conventional surface-mount assembly and simplifies inspection after soldering. The SOIC package also has a smaller body than larger power packages, although exposed-pad and heat-sink requirements must still be evaluated from the manufacturer's application guidance when operating continuously near the 275 mA output-current capability. Typical uses include ADSL customer-premises equipment, DSL line-interface cards, asymmetric digital subscriber line modems, and remote-terminal transmission stages. The same dual-channel topology can also serve other balanced, high-speed line interfaces when the signal amplitude, load, distortion, bandwidth, and supply requirements remain within the device's operating limits. Design the output return path and line interface carefully because the 275 mA output-current capability creates a meaningful load on the power supply and output network. Check transformer or termination-network behavior across the intended signal bandwidth, and use the manufacturer's recommended decoupling and layout practices to limit distortion and maintain high-frequency stability. This product page combines the exact manufacturer and distributor findings for the THS6092CD with package, application, sourcing, and drop-in comparison guidance. It also distinguishes electrically equivalent ordering options from genuine cross-package replacements so engineers can identify which components require a PCB redesign.

طلب عرض سعر اتصل بنا

THS6092ID

THS6092ID - 275mA +12V ADSL CPE Line Driver | Texas Instruments

The Texas Instruments THS6092ID is a 275 mA, +12 V ADSL CPE and DSL line driver packaged in an 8-pin SOIC (D). It provides a high-speed dual-channel output stage for driving signals between the remote terminal and the central office, with a specified low total harmonic distortion of -72 dBc into a 25 Ω load at 2 Vpp. The device is intended for asymmetrical digital subscriber line equipment and other high-speed line-driver applications. An ADSL line driver is an interface IC that converts upstream and downstream data signals into high-amplitude voltage waveforms suitable for transmission over twisted-pair telephone lines. Within the broader signal-chain hierarchy, the THS6092 belongs to the line-driver and transceiver class of interface ICs, which connects digital data-processing equipment to physical communication media. Its dual-channel architecture supports two independently driven line outputs while simplifying the analog output stage of a customer-premises equipment design. Key features include operation from a single +12 V supply, supply current of 7.3 mA per channel, and 275 mA output-current capability. The device can produce an output swing of 18.4 Vpp, while its -72 dBc distortion at 2 Vpp into a 25 Ω load provides a meaningful margin for reducing nonlinear harmonics. The industrial temperature option covers -40 °C to +85 °C, supporting telecommunications equipment expected to operate across extended environmental conditions. Technically, the THS6092 combines high-speed amplification with a high-current output stage suitable for driving capacitive and resistive line loads. The 275 mA rating identifies the output-current capability rather than the 7.3 mA quiescent supply consumption, so engineers should evaluate both values separately. Its specified distortion behavior is especially relevant where signal fidelity must remain controlled through a long copper pair and an external transformer or protection network. Typical applications include ADSL customer-premises equipment, DSL line-interface cards, central-office line-driver modules, and other telecommunications equipment requiring high-voltage, high-current outputs. The integrated dual-driver arrangement reduces the number of separate output stages while supporting the voltage and current levels expected in line-driving circuits. A critical design consideration is the distinction between the THS6092 and THS6093 versions. Confirm the required channel polarity and control configuration against the exact data sheet before substitution. Also account for transformer turns ratio, line impedance, protection components, output waveform limits, and thermal dissipation when defining the external drive network. This page consolidates manufacturer specifications, package details, lifecycle-oriented ordering information, verified source links, and same-family replacement guidance. It also highlights the engineering parameters that should be checked before treating another THS6092-family device as a drop-in choice.

طلب عرض سعر اتصل بنا

THS6093CD

THS6093CD - 275mA +12V ADSL Line Driver | Texas Instruments

The Texas Instruments THS6093CD is a 275 mA, +12 V ADSL CPE and PLC line driver with shutdown, packaged in a 14-pin SOIC. It is designed for high-speed line-driving applications using either a 1:2 transformer ratio or single-supply operation. Its headline characteristics are 275 mA output current, +12 V supply operation, a 14-SOIC package, low 2.1 pA/√Hz noninverting current noise, and a shutdown function. An ADSL line driver is an interface integrated circuit that converts upstream data signals into suitable current and voltage levels for transmission over copper lines. It belongs to the interface IC hierarchy within integrated circuits and semiconductor signal-conditioning devices. The THS6093 is intended for full-rate ADSL and G.Lite equipment, including customer-premises equipment and power-line communication equipment where the line interface must combine high output current with controlled noise. Key features include compatibility with a 1:2 transformer ratio, a wide supply-voltage range, and suitability for single +12 V operation. The 275 mA output capability provides useful drive current for line termination and transformer coupling. The device also includes shutdown control, allowing a system to disable the driver when line transmission is not required. Low noninverting current noise of 2.1 pA/√Hz helps reduce noise coupled through a telephone hybrid into the downstream receiver path. The THS6093 uses a high-current output stage suited to the demanding load presented by an ADSL line interface. Its architecture supports both transformer-coupled and single-supply arrangements, giving designers flexibility in line-network topology. The 14-pin SOIC package is a conventional surface-mount format suitable for automated PCB assembly, although the high-current output path requires careful routing, thermal review, and adequate copper around the power and ground pins. Typical uses include ADSL CPE line interfaces, full-rate ADSL modems, G.Lite access equipment, PLC gateways, and communications terminals connected to copper lines. It is particularly relevant when the design needs a dedicated line driver with a shutdown control and operation from a +12 V supply rather than a general-purpose low-power amplifier. For PCB implementation, place the device close to the line-transformancer or network interface and keep the high-current output path compact. Use a low-inductance supply connection and adequate input and output bypassing according to the manufacturer application guidance. Verify maximum output current, voltage, and thermal conditions across temperature because 275 mA describes the line-driver capability rather than unlimited continuous load capacity. This product record combines the manufacturer identification, package information, current capability, major ADSL and PLC use cases, and practical implementation considerations. It also provides sourcing guidance for the exact THS6093CD ordering code and distinguishes confirmed specifications from parameters that still require confirmation from the manufacturer datasheet.

طلب عرض سعر اتصل بنا

THS6093ID

THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments

Texas Instruments THS6093ID is a dual-channel, high-speed ADSL CPE line driver rated for 275 mA output current and +12 V operation in a 14-pin SOIC package. The device is intended for driving signals from the remote terminal toward the central office in asymmetric digital subscriber line systems, including full-rate ADSL and G.Lite configurations. An ADSL line driver is a specialized interface-circuit component that converts upstream driver signals into robust, high-current line outputs suitable for copper telephone networks. It sits within the power-management and signal-conditioning hierarchy of a customer premises equipment design, translating logic-level commands into line-side waveforms while helping preserve signal integrity across the transformer-coupled network. Key features include a wide supply-voltage range, suitability for single +12 V operation, compatibility with a 1:2 transformer ratio, and low 2.1 pA/√Hz noninverting current noise. The THS6093 also provides low total harmonic distortion of -72 dBc while driving the line and includes shutdown control. Each channel draws only 7.3 mA of supply current, helping limit the power burden of a multi-output access circuit. The device uses two noninverting outputs in a 14-pin SOIC package. Its high output-current capability is important for ADSL line interfaces because the external transformer, network loading, and cable losses can require substantially more current than a conventional logic driver. The specified 275 mA rating provides the core design limit for transformer selection, copper-line loading, supply capability, and thermal analysis. Typical uses include full-rate ADSL customer premises equipment, G.Lite ADSL line interfaces, and power-line carrier line-driver circuits. In each application, the THS6093 can operate from a single +12 V rail and drive the line through an appropriate external transformer while the shutdown function provides a controlled path for reducing activity when the endpoint is inactive. The primary design consideration is ensuring that the +12 V supply, output-current demand, transformer ratio, load, thermal conditions, and signal-integrity expectations all agree. Use the manufacturer datasheet pin-description table when assigning PCB nets, and confirm that the selected transformer supports the specified 1:2 ratio and operating bandwidth.

طلب عرض سعر اتصل بنا

الفئات الفرعية

المنتجات (38,000+)

THS4505DR - Wideband Fully Differential Amplifier | Texas Instruments

THS4522 - 95MHz Low Power Dual FDA | Texas Instruments

THS4531A - Ultra-Low-Power Fully Differential Amplifier | TI

THS4531ID - Ultra-Low-Power Differential Amplifier | TI

THS4532 - Dual 0.25mA RRO Fully-Differential Amplifier | TI

THS4551IRGTR - 150MHz Fully Diff Amp | Texas Instruments

THS4551IRGTT - 150MHz Low-Noise Fully Diff Amplifier | Texas Instruments

THS4601ID - 180MHz FET-Input Op Amp | Texas Instruments

THS4631D - 210MHz High-Speed FET Op Amp | Texas Instruments

THS6042CD - 350mA ±12V ADSL CPE Driver | Texas Instruments

THS6042ID - 350mA ADSL CPE Line Driver | Texas Instruments

THS6043CD - 350mA ±12V ADSL Line Driver | Texas Instruments

THS6043ID - 350mA ±12V ADSL CPE Line Driver | TI

THS6052CD - 175mA ±12V ADSL CPE Line Driver | TI

THS6053CD - 175mA ADSL Line Driver | Texas Instruments

THS6053ID - 175mA Dual ADSL Line Driver | Texas Instruments

THS6062CD - 100 MHz Low-Noise ADSL Receiver | Texas Instruments

THS6062ID - 100MHz Dual Differential Receiver | Texas Instruments

THS6072CD - Low-Power ADSL Differential Receiver, 175 MHz | Texas Instruments

THS6072ID - 175MHz Low-Power ADSL Receiver | TI

THS6092CD - 275mA +12V ADSL Driver | Texas Instruments

THS6092ID - 275mA +12V ADSL CPE Line Driver | Texas Instruments

THS6093CD - 275mA +12V ADSL Line Driver | Texas Instruments

THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments