المنتجات (44,000+)

TP2274 - 36V Quad 7MHz EMI-Hardened CMOS Op-Amp | 3PEAK
TP2274

TP2274 - 36V Quad 7MHz EMI-Hardened CMOS Op-Amp | 3PEAK

The 3PEAK TP2274 is a quad-channel, 36-V CMOS operational amplifier featuring EMI hardening (EMIRR of 84 dB at 900 MHz), 7-MHz gain-bandwidth product, 20-V/μs slew rate, and rail-to-rail output (RRO) swing in a 14-pin SOIC package. It operates from a single 2.7 V to 36 V supply (or dual ±1.35 V to ±18 V) and is unity-gain stable driving up to 100 pF of capacitive load, making it suitable for I/V converters, active filters, and transducer front-ends. A CMOS operational amplifier is a high-gain DC-coupled differential amplifier built on a complementary metal-oxide-semiconductor process. CMOS op-amps combine low input bias current (sub-pA to pA range), rail-to-rail output capability, and low quiescent current, and they form a hypernym hierarchy of linear IC -> amplifier IC -> operational amplifier -> CMOS op-amp. The TP2274 family (TP2271 single, TP2272 dual, TP2274 quad) is targeted at precision, low-voltage applications where EMI immunity is required, replacing general-purpose bipolar parts in noise-dense environments such as industrial sensor conditioning and motor-drive boards. Key features include a typical input offset voltage (Vos) of 1 mV maximum, 19 nV/√Hz input voltage noise density at 1 kHz, 126 dB open-loop DC gain (AOL), 80 mA short-circuit output current, and an operating temperature range of -40 °C to +125 °C. The TP2274 also offers 2 µV/°C offset drift and 900 µA typical quiescent current per amplifier, balancing speed with low power consumption for portable instrumentation. Internally, the TP2274 uses a CMOS input stage with an EMI-hardened front end and a class-AB output stage for rail-to-rail swing. Its 7-MHz GBW and 20-V/μs slew rate are tuned for medium-speed signal-chain applications rather than high-precision instrumentation, and the 84 dB EMIRR at 900 MHz allows the amplifier to reject RF interference from nearby switching regulators and wireless modules without rectification-induced DC errors. Typical applications include current-sensing I/V converters, multi-channel sensor signal conditioning, active filters in audio front-ends, and general-purpose signal amplification in industrial, automotive, and consumer systems. A common companion part is a high-precision ADC such as the ADS1256 for downstream digitization, or a low-dropout regulator to feed the analog supply rail. When designing with this device, keep input and feedback traces short to preserve the 7-MHz bandwidth and minimize parasitic capacitance, and add a small series resistor (10-50 Ω) at the output when driving more than a few hundred picofarads. Use a stable, low-noise supply on the analog rail to fully exploit the EMIRR figure. This page synthesizes distributor pricing, drop-in cross-references, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
TPA301D - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA301D

TPA301D - 350mW Mono Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA301D is a 350 mW, mono, Class-AB audio power amplifier designed for low-voltage systems and internal-speaker drive. It supports 3.3 V and 5 V operation, uses a bridge-tied-load topology, and is supplied in an 8-pin SOIC package. At 3.3 V, the manufacturer specifies 250 mW continuous power into an 8 ohm BTL load at less than 1% THD+N throughout the voice band. The device includes shutdown operation with 0.15 uA quiescent current, thermal protection, and short-circuit protection, making it suitable for portable audio, voice interfaces, and compact embedded systems. An audio power amplifier is an integrated circuit that converts a low-level analog audio signal into sufficient current and voltage to drive a loudspeaker or other audio load. A mono Class-AB amplifier uses one signal channel, while the TPA301D BTL architecture places the load between two output nodes rather than connecting one output to ground. This arrangement can improve speaker drive efficiency while requiring correct differential output routing and suitable input/output decoupling. The principal verified features are 350 mW class output capability, 3.3 V and 5 V supply compatibility, an 8-pin SOIC package, low 0.15 uA shutdown quiescent current, and integrated thermal and short-circuit protection. The TPA301 family also offers a surface-mount PowerPAD MSOP option according to the TI product page, although the TPA301D orderable variant is identified as 8-SOIC by distributor data. The manufacturer explicitly states that no special bypassing, gain-setting, or stability adjustments are required merely because the supply is 3.3 V rather than 5 V; output power is the important operating consideration. Because the part is designed around low-voltage BTL audio drive, circuit layout should preserve the differential output topology and place required capacitors close to the device pins. The input and output networks should be checked against the manufacturer datasheet for the selected supply, gain, load, and operating mode. The device should not be selected solely by its nominal 350 mW label: continuous speaker power, distortion, thermal conditions, supply headroom, and available PCB area determine practical performance. Typical applications include portable voice boxes, compact speakers, personal-audio accessories, embedded audio modules, and low-voltage consumer products. In a 3.3 V system, the verified 250 mW into 8 ohms condition provides a useful baseline, while 5 V operation provides additional output capability. For applications requiring more power, a different amplifier class or package should be evaluated rather than assuming that a higher supply alone preserves the same thermal and distortion performance. A practical design tip is to validate the speaker impedance and wiring before layout approval. A BTL amplifier must never be configured like a single-ended amplifier with one output grounded. Review the TI datasheet for recommended input, bypass, feedback, output, and decoupling networks, then test worst-case low-supply, high-temperature, maximum-volume conditions. This page combines verified manufacturer and distributor information with practical selection guidance, datasheet-oriented FAQs, and engineering-oriented design notes. It is intended to help engineers identify whether the TPA301D fits a low-voltage mono-speaker design before committing to a PCB footprint or supply architecture.

طلب عرض سعر اتصل بنا
TPA301DGH - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA301DGH

TPA301DGH - 350mW Mono Class-AB Amplifier | Texas Instruments

Texas Instruments TPA301DGH is a 350mW mono Class-AB audio power amplifier designed for low-voltage, bridge-tied-load (BTL) speaker systems. The device operates from a 3.3V supply and can deliver 250mW of continuous power into an 8Ω BTL load at less than 1% THD+N throughout the voice band. Its primary package designation is DGH, although the exact package dimensions and pin count are not confirmed in the supplied verified data and therefore are not inferred here. An audio power amplifier is an integrated circuit that converts low-level audio signals into current and voltage capable of driving a loudspeaker or other electroacoustic load. The TPA301 belongs to the Class-AB audio amplifier hierarchy, which sits within integrated amplifier ICs and the broader power management and analog signal-processing semiconductor categories. A BTL output arrangement uses both sides of the speaker to develop voltage swing while avoiding the need for a single-ended output coupling capacitor. The principal performance characteristics include 350mW nominal output power, operation from a 3.3V supply, and 250mW continuous output into an 8Ω BTL load. According to the Texas Instruments TPA301 product information, total harmonic distortion plus noise remains below 1% across voice-band frequencies under the stated operating condition. Although the amplifier is characterized through 20kHz, its operation is optimized for voice-band audio rather than high-fidelity full-range reproduction. The Class-AB output stage provides a practical compromise between conduction efficiency and signal linearity. Compared with a switching audio amplifier, the TPA301 avoids the high-frequency switching artifacts and electromagnetic interference commonly associated with converter-based power stages. Conversely, a linear Class-AB amplifier dissipates more power as the supply-to-load voltage difference increases, making load selection and supply voltage important during thermal and battery-budget analysis. Typical uses include portable speakers, voice-enabled personal audio products, compact sound modules, and low-voltage embedded audio systems. The 3.3V supply requirement aligns with portable equipment powered by regulated batteries or point-of-load rails, while the 250mW capability into 8Ω is suitable for small internal speakers. System designers must still verify speaker impedance, peak current, thermal rise, output distortion, and startup behavior against the complete manufacturer datasheet. When designing around the TPA301DGH, preserve the manufacturer-recommended input, bypass, and output-network layout. Do not infer a pin configuration or exposed-pad connection from the DGH ordering code alone. Confirm the exact package drawing, exposed thermal-pad requirements, maximum supply voltage, output-current limits, and operating-temperature limits against the current Texas Instruments documentation before releasing a PCB design. This page consolidates verified manufacturer and distributor information, current Rochester Electronics pricing, application guidance, design cautions, and substitution-status findings. It explicitly separates confirmed specifications from unavailable parameters so engineers can trace each decision to source data rather than relying on an unverified generic TPA301 listing.

طلب عرض سعر اتصل بنا
TPA301DGN - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA301DGN

TPA301DGN - 350mW Mono Class-AB Amplifier | Texas Instruments

Texas Instruments TPA301DGN is a 350 mW mono Class-AB audio power amplifier operating from a low-voltage supply in an 8-pin HVSSOP (DGN) package. It is designed for internal-speaker applications and supports a 3.3 V supply, where it can deliver 250 mW continuously into an 8-ohm bridge-tied-load speaker with less than 1% THD+N through the voice band. The device also supports 5 V operation and is characterized for frequencies up to 20 kHz. An audio power amplifier is an integrated circuit that converts a low-level audio input signal into a current and voltage capable of driving a loudspeaker or other high-impedance acoustic load. The TPA301 belongs to the Class-AB audio amplifier hierarchy, where output transistors conduct for part of each signal cycle to balance efficiency and low crossover distortion. Its bridge-tied-load topology develops an output across the two speaker terminals without requiring a DC-blocking capacitor. The TPA301 is specified for both 3.3 V and 5 V supply operation, providing broad compatibility with portable and low-voltage embedded systems. Its 350 mW headline output capability is suitable for compact internal speakers, while the 250 mW result at 3.3 V into 8 ohms is especially relevant to battery-powered equipment. The manufacturer describes operation as optimized for the voice band, although the device is characterized through 20 kHz. Thermal and short-circuit protection support reliable operation in compact audio products, while shutdown mode limits quiescent current to 0.15 microamps according to the available component data. These characteristics make the TPA301 applicable to portable speakers, personal-audio accessories, embedded audio products, and other compact systems where supply headroom is limited. The 8-pin HVSSOP package also reduces board area compared with larger leaded audio-amplifier packages. A BTL output requires the speaker to be connected between the two output terminals; connecting either output terminal to ground is not an equivalent single-ended configuration. Designers should also verify the complete speaker-impedance range, supply-voltage tolerance, thermal conditions, input-coupling network, and output-routing requirements against the manufacturer datasheet before production release. This page consolidates the verified manufacturer and distributor information for the TPA301DGN, including its 350 mW mono Class-AB configuration, low-voltage operating range, 8-pin HVSSOP format, candidate comparison parts, and practical implementation guidance. It is intended to support engineering selection while clearly separating verified specifications from data that still requires manufacturer-datasheet confirmation.

طلب عرض سعر اتصل بنا
TPA301DGNR - 350mW Mono Class-AB Amplifier | Texas Instruments (Tape & Reel)
TPA301DGNR

TPA301DGNR - 350mW Mono Class-AB Amplifier | Texas Instruments (Tape & Reel)

Texas Instruments TPA301DGNR is a 350 mW mono Class-AB audio power amplifier operating from a low-voltage supply in an 8-pin HVSSOP (DGN) package. It is designed for internal-speaker applications and supports a 3.3 V supply, where it can deliver 250 mW continuously into an 8-ohm bridge-tied-load speaker with less than 1% THD+N through the voice band. The device also supports 5 V operation and is characterized for frequencies up to 20 kHz. An audio power amplifier is an integrated circuit that converts a low-level audio input signal into a current and voltage capable of driving a loudspeaker or other high-impedance acoustic load. The TPA301 belongs to the Class-AB audio amplifier hierarchy, where output transistors conduct for part of each signal cycle to balance efficiency and low crossover distortion. Its bridge-tied-load topology develops an output across the two speaker terminals without requiring a DC-blocking capacitor. The TPA301 is specified for both 3.3 V and 5 V supply operation, providing broad compatibility with portable and low-voltage embedded systems. Its 350 mW headline output capability is suitable for compact internal speakers, while the 250 mW result at 3.3 V into 8 ohms is especially relevant to battery-powered equipment. The manufacturer describes operation as optimized for the voice band, although the device is characterized through 20 kHz. Thermal and short-circuit protection support reliable operation in compact audio products, while shutdown mode limits quiescent current to 0.15 microamps according to the available component data. These characteristics make the TPA301 applicable to portable speakers, personal-audio accessories, embedded audio products, and other compact systems where supply headroom is limited. The 8-pin HVSSOP package also reduces board area compared with larger leaded audio-amplifier packages. A BTL output requires the speaker to be connected between the two output terminals; connecting either output terminal to ground is not an equivalent single-ended configuration. Designers should also verify the complete speaker-impedance range, supply-voltage tolerance, thermal conditions, input-coupling network, and output-routing requirements against the manufacturer datasheet before production release. This page consolidates the verified manufacturer and distributor information for the TPA301DGNR, including its 350 mW mono Class-AB configuration, low-voltage operating range, 8-pin HVSSOP format, candidate comparison parts, and practical implementation guidance. It is intended to support engineering selection while clearly separating verified specifications from data that still requires manufacturer-datasheet confirmation.

طلب عرض سعر اتصل بنا
TPA301DR - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA301DR

TPA301DR - 350mW Mono Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA301DR is a 350 mW mono Class-AB audio power amplifier designed for 3.3 V and 5 V operation, with a bridge-tied-load output and an 8-pin SOIC package. The device delivers 250 mW continuously into an 8 ohm BTL load from a 3.3 V supply at less than 1% THD+N through the voice band. Its Class-AB architecture is intended for compact internal speakers where low supply voltage, simple integration, and adequate output power matter more than maximum efficiency. The TPA301DR family is specified for common 3.3 V and 5 V rails, while its shutdown behavior supports portable equipment. The bridge-tied-load topology drives the speaker differentially, eliminating the need for an output coupling capacitor in the typical application. However, the speaker terminals cannot be connected to ground or chassis ground because each output switches around the midpoint of the supply. According to the verified Texas Instruments product page and TPA301 datasheet, the device is optimized for low-voltage systems using internal speakers. The manufacturer emphasizes that output power is the principal consideration when comparing 3.3 V and 5 V operation; supply bypassing, gain settings, and stability do not require special changes between those rails. The SOIC-8 footprint supports conventional surface-mount assembly, while thermal design remains important because Class-AB output stages dissipate more power than switching amplifiers at low output levels. System designers should verify speaker impedance, gain, supply bypassing, thermal exposure, and shutdown polarity against the datasheet before production release.

طلب عرض سعر اتصل بنا
TPA301DRG4 - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA301DRG4

TPA301DRG4 - 350mW Mono Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA301DRG4 is a 350 mW mono Class-AB audio power amplifier designed for low-voltage portable equipment and compact audio systems. The device supports operation from a low-voltage supply and is available in an 8-pin SOIC package. The TPA301 family is intended for applications where a small, efficient audio output stage is required to drive an internal speaker or other low-impedance audio load. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so that a speaker can produce usable sound. The TPA301 belongs to the Class-AB amplifier category within the broader linear audio amplifier hierarchy. Class-AB operation provides a practical compromise between output efficiency and low crossover distortion, making this device appropriate for portable consumer products, small speakers, portable audio equipment, and low-cost consumer electronics. The manufacturer describes the TPA301 as a 350 mW mono audio power amplifier with operation specified for 3.3 V and 5 V supplies. The device includes thermal and short-circuit protection and is optimized for compatibility across 3.3 V and 5 V systems. Its shutdown-mode quiescent current is specified as ultra-low, which helps reduce standby power consumption in portable equipment. The amplifier also uses a bridge-tied-load configuration when driving an internal speaker. The TPA301DRG4 uses an 8-pin SOIC package and is identified by the DRG4 ordering suffix. The manufacturer product page identifies the device as a 350 mW, mono, Class-AB audio amplifier. The product family is suitable for compact products where a single audio channel is required, such as personal audio players, portable speakers, alarm devices, small appliances, and auxiliary audio products. When designing a circuit around the TPA301DRG4, confirm the supply voltage, speaker impedance, output-power requirement, and the manufacturer’s recommended input and bypass capacitors. The device’s bridge-tied-load output arrangement determines which output nodes are used with the speaker. Decoupling capacitors should be placed close to the supply pins, while the speaker wiring and ground return should be routed to minimize noise and unintended coupling into the audio path. This page combines the manufacturer product information, distributor listings, package details, and application guidance with practical design notes and verified substitution information. Use the Texas Instruments TPA301 product page and datasheet as the authoritative references for pin functions, recommended application circuits, absolute maximum ratings, thermal limits, and production ordering information.

طلب عرض سعر اتصل بنا
TPA302D - 300mW Stereo Class-AB Amplifier | Texas Instruments
TPA302D

TPA302D - 300mW Stereo Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA302D is a 300 mW stereo, analog-input Class-AB audio power amplifier with two output channels and an 8-pin SOIC (D) package. It is designed for compact audio systems operating from 5 V and 3.3 V supplies. The manufacturer describes 250 mW continuous average output per channel into an 8-ohm load and 60 mW at less than 0.06% THD+N. A Class-AB audio amplifier is a linear power-amplifier category that combines an analog input signal with transistor output stages capable of driving speakers and other finite loads. The TPA302D belongs to the broader hierarchy of audio amplifiers, audio ICs, analog signal-conditioning ICs, and semiconductor devices. Its stereo architecture supports two audio channels while its analog inputs permit direct connection to conventional audio sources. Key features include shutdown control, internal mid-rail generation, thermal protection, and short-circuit protection. The device is also identified as a functional equivalent of the LM4880 in the supplied technical data. Its 8-pin SOIC package reduces board space and supports automated surface-mount assembly. The verified product information specifically identifies the amplifier as a 300 mW stereo Class-AB device with analog input. The TPA302 architecture uses separate left and right amplification paths to provide stereo output from analog input signals. The internal mid-rail feature can support single-supply audio architectures, while shutdown control allows the system to place the amplifier in a lower-power state when audio is not required. The datasheet and product listing also indicate compatibility with 5 V and 3.3 V operation, which makes the device relevant to portable equipment, small consumer audio products, and low-voltage embedded systems. Typical applications include compact stereo speakers, portable audio equipment, auxiliary audio products, USB or docking-system audio paths, and small embedded audio subsystems. The 8-ohm speaker-load target and 250 mW continuous average capability are suitable for low-to-moderate listening levels, although the available output power depends on supply voltage, load impedance, channel balance, thermal conditions, and signal level. Designers should verify the SOIC footprint, supply decoupling, output-filter requirements, speaker wiring, thermal rise, and shutdown polarity against the manufacturer datasheet before layout release. The device is not a Class-D switching amplifier, so its output-stage dissipation and analog signal integrity should be checked carefully in continuous-use designs.

طلب عرض سعر اتصل بنا
TPA302DR - 300mW Stereo Class-AB Amplifier | Texas Instruments
TPA302DR

TPA302DR - 300mW Stereo Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA302DR is a 300 mW stereo analog-input Class-AB audio amplifier with a 1.5 MHz bandwidth, 5.5 V maximum supply voltage, and an 8-pin SOIC package. It delivers 250 mW per channel into an 8-ohm load and provides 60 mW of continuous output power at less than 0.06% THD+N. Designed for compact audio systems, the TPA302DR combines stereo output, internal mid-rail generation, shutdown control, and thermal and short-circuit protection in a low-profile surface-mount package. A Class-AB audio amplifier is an analog signal-processing integrated circuit that uses push-pull transistor output stages to drive speakers or other low-impedance loads. The TPA302DR belongs to the broader audio-amplifier hierarchy, which includes stereo amplifiers, linear amplifiers, and semiconductor power amplifiers. Its Class-AB architecture provides continuous bipolar output rather than the pulsed output associated with Class-D designs, making it suitable for low-power portable, personal-audio, and auxiliary audio products. Key features include 300 mW stereo output capability, 1.5 MHz bandwidth, operation from 5 V and 3.3 V rails, internally generated mid-rail voltage, shutdown control, and thermal and short-circuit protection. The 8-pin SOIC package reduces board area and supports automated surface-mount assembly. These characteristics make the device useful where two analog audio channels must drive headphones or small speakers without the complexity of a switching amplifier and external mid-rail circuitry. The amplifier accepts analog left- and right-channel inputs and uses external gain-setting resistors to establish channel gain. According to the Texas Instruments TPA302 data sheet, the device is specified for operation from a 5 V supply and is also compatible with 3.3 V operation. Its internally generated mid-rail provides a convenient common return for single-supply audio signals, while the shutdown function can reduce supply consumption when the audio path is not active. Typical applications include portable speakers, headphone and headset drivers, personal-audio accessories, small consumer-audio systems, and compact embedded audio products. The 250 mW-per-channel capability into 8 ohms is appropriate for low-impedance transducers rather than high-power loudspeaker systems. System designers should confirm speaker impedance, amplifier gain, input coupling, output configuration, and power-supply headroom before finalizing the analog and layout design. A key design consideration is the distinction between the 300 mW headline output rating and the verified application condition of 250 mW per channel into 8 ohms. Allow for copper, nearby heat sources, enclosure temperature, and supply tolerance, and use the datasheet thermal information to assess reliable operation. This page synthesizes verified manufacturer and distributor information, engineering design notes, comparison data, and drop-in replacement guidance beyond the basic distributor listing.

طلب عرض سعر اتصل بنا
TPA311D - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA311D

TPA311D - 350mW Mono Class-AB Amplifier | Texas Instruments

The Texas Instruments TPA311D is a 350 mW mono Class-AB audio amplifier with bridge-tied-load to single-ended switching mode, specified for 3.3 V and 5 V operation and housed in an 8-pin SOIC package. It is designed for low-voltage audio paths where an internal speaker and external earphone may share the same system. According to the verified distributor listing, TPA311D is a one-channel mono Class-AB amplifier in an 8-SOIC package. A Class-AB audio amplifier is a linear audio amplifier whose output devices conduct for part of the signal cycle. In the audio-power hierarchy, it provides a relatively linear output with less switching-related EMI than many Class-D solutions, making it useful in compact voice, portable-device, and low-voltage speaker systems. The TPA311 family also supports bridge-tied-load and single-ended operating modes, allowing the device to serve internal-speaker and earphone paths with appropriate output configuration. The verified data identifies the TPA311 as a 350 mW mono audio power amplifier and highlights operation at 3.3 V and 5 V, wide power-supply compatibility, bridge-tied-load to single-ended mode control, integrated depop circuitry, and thermal and short-circuit protection. The manufacturer product page describes 250 mW continuous power into a bridge-tied 8-ohm load at less than 1% THD+N throughout voice-band frequencies when operated from a 3.3 V supply. These figures describe the TPA311 family context associated with TPA311D. The architecture is suitable for compact audio equipment where a low-voltage supply limits available output power. The integrated protection features help manage thermal and short-circuit conditions, while depop circuitry helps control output transients during startup or mode changes. Engineers should still validate speaker impedance, supply headroom, thermal dissipation, and the selected output topology against the manufacturer datasheet before releasing a production PCB. Typical uses include portable audio products, voice-enabled devices, small speaker systems, headphone or earphone interfaces, and embedded audio subsystems. The 8-SOIC package simplifies assembly for designs using conventional surface-mount production processes. Because the target is a legacy audio amplifier family, availability, lifecycle status, pricing, and exact electrical limits should be reconfirmed from current manufacturer and distributor data. A key design consideration is the difference between the family headline rating of 350 mW and the verified 3.3 V application condition of 250 mW into an 8-ohm BTL load at less than 1% THD+N. The circuit must be designed around the actual supply, load, package thermal behavior, and output mode rather than treating the headline power as an unconditional speaker rating. This page combines verified source data with structured engineering guidance and clearly identifies unavailable parameters.

طلب عرض سعر اتصل بنا
TPA311DG4 - 350mW Mono Class AB Amplifier | Texas Instruments
TPA311DG4

TPA311DG4 - 350mW Mono Class AB Amplifier | Texas Instruments

The Texas Instruments TPA311DG4 is a 350 mW mono audio power amplifier IC for low-voltage audio systems, operating from 3.3 V or 5 V and housed in an 8-pin SOIC surface-mount package. It is a Class AB amplifier that supports bridge-tied load (BTL) and single-ended (SE) operating modes, includes integrated depop circuitry, and provides thermal and short-circuit protection. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a speaker or another defined load. In the broader hierarchy, the TPA311DG4 is a mono Class AB audio amplifier, an amplifier IC, an integrated circuit, and a discrete signal-processing component for low-voltage audio equipment. Its BTL architecture allows an internal speaker to be driven without a speaker-blocking capacitor, while SE mode supports external earphone operation. The device is specified for 3.3 V and 5 V operation, with a maximum supply voltage of 5.5 V. Its 350 mW output-power description makes it suitable for compact internal speakers and low-power audio paths. A distributor listing also reports 0.7 W nominal output power, but the manufacturer-linked search description identifies the TPA311DG4 specifically as a 350 mW mono audio power amplifier. System designers should therefore confirm the exact test conditions and load used in the manufacturer datasheet before sizing the speaker and supply. The TPA311 family combines a fully specified low-voltage operating range with BTL-to-SE mode control, integrated depop circuitry, and built-in thermal and short-circuit protection. These features make the amplifier appropriate for products using either 3.3 V or 5 V system rails. The 8-pin SOIC package also supports automated assembly and compact board layouts, although adequate copper and thermal layout remain necessary when continuous audio output causes appreciable internal dissipation. Typical applications include portable speaker systems, compact consumer audio products, and low-voltage equipment requiring an internal mono speaker plus an external headphone path. The part can also serve as the power stage in a larger audio subsystem when the design only requires a small speaker output. Its protection functions reduce system risk during abnormal load conditions, but they do not replace correct speaker impedance selection, supply decoupling, or thermal design. A key design consideration is the difference between BTL and SE mode. In BTL mode, the amplifier drives the speaker differentially and does not require an output coupling capacitor. In SE mode, one output is referenced differently to support an earphone load. Designers should follow the manufacturer configuration, component values, and decoupling guidance rather than assuming that the two modes have identical load, output-power, or stability requirements. This product page consolidates the verified manufacturer and distributor descriptions for the TPA311DG4, identifies the available pin-compatible family comparisons, and adds application guidance that is not presented as a substitute for the official electrical characteristics, absolute maximum ratings, and test-condition tables in the manufacturer datasheet.

طلب عرض سعر اتصل بنا
TPA311DGN - 350mW Mono Class-AB Audio Amplifier | Texas Instruments
TPA311DGN

TPA311DGN - 350mW Mono Class-AB Audio Amplifier | Texas Instruments

The Texas Instruments TPA311DGN is a 350 mW, mono, Class-AB audio amplifier with bridge-tied load (BTL) or single-ended output capability, designed for low-voltage portable audio systems. The device operates from a 3.3 V supply and is specified to deliver up to 250 mW continuous power into an 8 ohm BTL load at less than 1% THD+N, according to the manufacturer product information. It is packaged in an 8-pin HVSSOP DGN surface-mount package with a PowerPAD thermal pad. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a speaker or other low-impedance transducer. A BTL arrangement uses both output terminals to drive the speaker differentially, which increases voltage swing and can reduce the need for an output coupling capacitor. A Class-AB output stage provides continuous conduction with lower crossover distortion than a typical Class-D architecture, making the TPA311 useful for small speakers, internal speakers, and portable audio products. Key features include mono operation, a 350 mW output-power rating, Class-AB operation, BTL and single-ended modes, shutdown support with speaker-noise reduction, and an 8-pin HVSSOP package. The product information identifies the amplifier as a 3.3 V, 8 ohm audio solution with approximately 1.4 MHz switching or operating frequency information shown by a distributor listing; the exact interpretation of that frequency should be confirmed against the manufacturer datasheet for the specific design configuration. The TPA311 is appropriate for portable media players, compact speakers, personal audio products, and low-voltage embedded systems where a mono speaker is sufficient. In a typical implementation, the audio source drives the amplifier input through the device's gain-setting network, while the BTL output connects directly across the speaker. The single-ended output option can support headphone-style or externally terminated loads, subject to the datasheet's output and load restrictions. Designers should pay close attention to supply decoupling, speaker impedance, thermal performance of the exposed pad, and the distinction between BTL and single-ended wiring. The HVSSOP package improves board-space efficiency compared with the larger 8-pin SOIC option, while the PowerPAD provides a thermal connection to the PCB copper area. Application details, limit values, gain options, and recommended external components must be taken from the manufacturer datasheet rather than inferred from distributor summaries.

طلب عرض سعر اتصل بنا
TPA311DGNR - 350mW Mono Class-AB Audio Amplifier | Texas Instruments (Tape & Reel)
TPA311DGNR

TPA311DGNR - 350mW Mono Class-AB Audio Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments TPA311DGNR is a 350 mW, mono, Class-AB audio amplifier with bridge-tied load (BTL) or single-ended output capability, designed for low-voltage portable audio systems. The device operates from a 3.3 V supply and is specified to deliver up to 250 mW continuous power into an 8 ohm BTL load at less than 1% THD+N, according to the manufacturer product information. It is packaged in an 8-pin HVSSOP DGN surface-mount package with a PowerPAD thermal pad. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a speaker or other low-impedance transducer. A BTL arrangement uses both output terminals to drive the speaker differentially, which increases voltage swing and can reduce the need for an output coupling capacitor. A Class-AB output stage provides continuous conduction with lower crossover distortion than a typical Class-D architecture, making the TPA311 useful for small speakers, internal speakers, and portable audio products. Key features include mono operation, a 350 mW output-power rating, Class-AB operation, BTL and single-ended modes, shutdown support with speaker-noise reduction, and an 8-pin HVSSOP package. The product information identifies the amplifier as a 3.3 V, 8 ohm audio solution with approximately 1.4 MHz switching or operating frequency information shown by a distributor listing; the exact interpretation of that frequency should be confirmed against the manufacturer datasheet for the specific design configuration. The TPA311 is appropriate for portable media players, compact speakers, personal audio products, and low-voltage embedded systems where a mono speaker is sufficient. In a typical implementation, the audio source drives the amplifier input through the device's gain-setting network, while the BTL output connects directly across the speaker. The single-ended output option can support headphone-style or externally terminated loads, subject to the datasheet's output and load restrictions. Designers should pay close attention to supply decoupling, speaker impedance, thermal performance of the exposed pad, and the distinction between BTL and single-ended wiring. The HVSSOP package improves board-space efficiency compared with the larger 8-pin SOIC option, while the PowerPAD provides a thermal connection to the PCB copper area. Application details, limit values, gain options, and recommended external components must be taken from the manufacturer datasheet rather than inferred from distributor summaries.

طلب عرض سعر اتصل بنا
TPA311DR - 350mW Mono Class-AB Amplifier | Texas Instruments
TPA311DR

TPA311DR - 350mW Mono Class-AB Amplifier | Texas Instruments

Texas Instruments TPA311DR is a 350 mW mono Class-AB audio power amplifier with bridge-tied-load and single-ended operating modes, specified for operation from a 3.3 V supply and supplied in an 8-pin SOIC package. It is designed to drive internal speakers or external earphones in compact, low-voltage audio systems. According to the manufacturer product page, the TPA311 family supports fully specified 3.3 V and 5 V operation, integrated BTL-to-SE mode control, integrated depop circuitry, and thermal and short-circuit protection. The R suffix identifies the taped-and-reeled ordering option, while the device itself is a single-channel Class-AB audio amplifier. An audio power amplifier is an integrated circuit that converts a low-level audio input into a higher-current signal capable of driving a loudspeaker or other transducer. The TPA311 belongs to the Class-AB amplifier hierarchy within audio amplifiers and power-management ICs. Its bridge-tied-load mode increases usable output voltage into a differential speaker, while single-ended mode allows the same device to drive an external earphone when the system requires a grounded output. Key features include 350 mW rated output capability, compatibility with 3.3 V and 5 V supplies, integrated BTL-to-SE mode control, integrated depop circuitry, and built-in thermal and short-circuit protection. These features make the device suitable for portable audio, voice terminals, personal-audio products, and other compact systems in which a single-speaker or earphone output is needed without a large external amplifier module. The architecture is optimized for low-voltage operation. At a 3.3 V supply, the manufacturer documentation describes 250 mW continuous output into an 8-ohm BTL load at less than 1% THD+N across voice-band frequencies. The lower output-power figure reflects the device's 3.3 V operating condition; the family-level headline rating is 350 mW. BTL operation suppresses the DC output offset at the speaker and can provide greater output swing than a conventional single-ended amplifier. Typical applications include portable media players, personal audio accessories, voice-call terminals, compact speakers, and low-voltage embedded audio products. The TPA311DR can be selected when the board uses an 8-pin SOIC footprint and requires integrated protection rather than a discrete output stage. A key design consideration is output-mode configuration: the mode-control function must be connected or configured as required by the manufacturer reference design for the intended BTL or SE load. Input and output decoupling, speaker-return routing, thermal copper, and clean grounding are essential for low distortion and stable operation. This page consolidates verified manufacturer and distributor information, drop-in candidate screening, application guidance, and practical PCB considerations. It also distinguishes explicitly sourced facts from unavailable specifications, helping engineers make a defensible design decision without relying on a generic distributor listing alone.

طلب عرض سعر اتصل بنا
TPA3125D2N - 10W Stereo Class-D Amplifier | Texas Instruments
TPA3125D2N

TPA3125D2N - 10W Stereo Class-D Amplifier | Texas Instruments

Texas Instruments TPA3125D2N is a Class-D audio power amplifier rated for 10 W per channel in stereo single-ended operation and 20 W in mono bridge-tied-load operation. It accepts a 10 V to 26 V supply, supports analog input signals, and is offered in the TPA3125D2N configuration as a 20-pin PDIP package rated for -40°C to 85°C operation. A Class-D audio amplifier is a power-management semiconductor that converts analog input signals into high-frequency switching waveforms and reconstructs the amplified audio at the speaker output. The Class-D architecture belongs to the amplifier IC hierarchy and achieves high power-conversion efficiency compared with conventional linear audio amplifiers. This efficiency helps the TPA3125D2N eliminate the need for an external heat sink during normal music playback, although PCB layout and thermal design still require attention. The TPA3125D2 supports two principal operating arrangements. In stereo mode, its single-ended outputs can drive two speakers as low as 4 Ω, with up to 10 W delivered to each channel. In bridge-tied-load mode, the two output channels combine to drive one speaker at up to 20 W. Gain is controlled externally, allowing the signal-chain gain to be matched to the source level without relying on a fixed internal gain setting. The device is intended for analog-input audio systems where a compact, efficient power stage is required. Its supply range accommodates common amplified-speaker, multimedia, television, consumer-audio, and compact embedded systems. The 20-pin PDIP package favors through-hole assembly and repairability, while the operating-temperature range supports industrial-temperature applications requiring a broad ambient range. Class-D output stages demand careful PCB layout because high-frequency switching currents can create electromagnetic interference, ground bounce, and instability if output and input paths are not separated. Place the input and feedback components away from the switching outputs, keep speaker-current loops compact, and provide a low-impedance ground return. The decoupling network should follow the manufacturer’s recommended application circuit to control supply transients. The principal design trade-off is package size versus assembly convenience. The PDIP-20 body is larger than a surface-mount power package, but it is straightforward to assemble, inspect, and service. It is a practical choice for moderate-power audio products where efficient operation, analog gain control, stereo-to-mono flexibility, and straightforward through-hole construction outweigh the need for minimal PCB area. This product overview combines the manufacturer’s device description with a practical comparison of stereo and bridge-tied-load operation, output loading, package implications, thermal expectations, and layout considerations. It also identifies which candidate replacements have documented equivalence and where additional design verification is still required.

طلب عرض سعر اتصل بنا
TPA321D - 700mW Mono Class-AB Audio Amp | TI
TPA321D

TPA321D - 700mW Mono Class-AB Audio Amp | TI

The Texas Instruments TPA321D is a 700 mW mono analog-input Class-AB audio power amplifier with differential inputs, operating from 2.5 V to 5.5 V in an 8-pin SOIC package. It is designed for low-voltage systems that drive internal speakers through a bridge-tied-load output. An audio power amplifier is an integrated circuit that increases the voltage and current capability of an analog audio signal so it can drive a loudspeaker or other finite impedance. A Class-AB amplifier provides linear operation with lower crossover distortion than a traditional Class-B design. A differential input accepts signal voltage between two input terminals, while a bridge-tied-load output uses both amplifier outputs to develop voltage across the speaker without requiring a speaker-coupling capacitor. The TPA321 family is specified for 3.3 V and 5 V operation and supports a 2.5 V to 5.5 V supply range. At a 3.3 V supply, the manufacturer material states that the device can deliver 250 mW continuously into an 8-ohm bridge-tied load with less than 1% THD+N over the voice band. The TPA321D ordering option is supplied in the 8-pin SOIC package and supports a -40°C to +85°C operating-temperature range. Differential input architecture can help reject common-mode noise when the source is balanced or when noise appears equally on both input conductors. The bridge-tied-load topology places the speaker between OUT+ and OUT-, so neither output pin should be grounded merely to establish a common reference. Input, supply, and output stability components must be implemented according to the manufacturer datasheet to preserve stable operation and acceptable distortion. Typical uses include portable-device speakers, compact audio accessories, personal-audio products, and other low-voltage mono sound systems. The design is appropriate when a small internal speaker must be driven directly and board area is limited. At higher power or with a longer speaker connection, cable losses and load tolerance should be checked before release. Decoupling capacitors should be placed close to the supply pins, and input components should be arranged to minimize the audio trace area. Thermal performance depends on supply voltage, output power, speaker impedance, PCB copper, and ambient temperature. This page combines verified product information with purchasing guidance and design context. This data page distinguishes TPA321D from the broader TPA321 family, summarizes the electrically relevant evidence, and organizes sourcing and replacement questions. Values not explicitly supplied by the retrieved manufacturer or distributor data remain marked for verification rather than inferred.

طلب عرض سعر اتصل بنا
TPA321DG4 - 350mW Mono Class-D Audio Amp | Texas Instruments
TPA321DG4

TPA321DG4 - 350mW Mono Class-D Audio Amp | Texas Instruments

The Texas Instruments TPA321DG4 is a 350-mW mono Class-D audio power amplifier with differential inputs, specified for both 3.3 V and 5 V operation, and supplied in an 8-pin SOIC (DG4) package. It delivers its rated output into a minimum 8-ohm speaker load, draws only 0.15 microamps in shutdown mode, and limits idle supply current to 1.5 mA maximum, making it well suited to portable and low-voltage audio equipment. A Class-D audio power amplifier is a switching type of linear audio output stage in which the transistor output devices are driven fully on or fully off, so that the amplifier dissipates far less power than an equivalent Class-AB stage at the same output level. Within the broader hierarchy of audio signal-chain ICs, the TPA321DG4 sits in the power-amplifier tier, downstream of the audio DAC or codec and upstream of the loudspeaker, converting a low-level differential analog signal into a rail-to-rail differential speaker drive. Key features include full specification across a 3.3 V and 5 V supply range, differential inputs that reject common-mode noise picked up from long source traces, 0.5 percent harmonic distortion, a maximum power dissipation of 725 mW, and a maximum load resistance of 8 ohms. Shutdown current of 0.15 microamps preserves battery life in portable equipment, while the industrial temperature grade supports extended ambient operation. Internally the device uses a charge-pump-assisted Class-D output stage with differential outputs, so each output pin swings around half the supply rail. Because the outputs are differential, a bridge-tied load sees the full rail-to-rail swing and delivers roughly four times the power of a single-ended arrangement at the same supply voltage. The gain-setting and input network are entirely passive, keeping the external bill of materials small. Typical applications include compact Bluetooth and portable speakers, headset and headphone drive, USB and Type-C powered audio accessories, small Bluetooth speaker modules, alarm and industrial buzzer drivers, and low-voltage voice-assistant or smart-home nodes where a 3.3 V rail is the only supply available. Design note: because the device has differential inputs and differential outputs, do not ground the input pins or tie the two output pins together. Place the input coupling capacitors and the input resistors close to the pins, route the differential pair as a tight pair to limit common-mode pickup, and terminate each output through its own LC filter network into the speaker. This page synthesizes distributor availability, pin-compatible drop-in alternatives, a parameter-by-parameter comparison, and practical layout and thermal notes that are not consolidated in the manufacturer datasheet itself.

طلب عرض سعر اتصل بنا
TPA321DGN - 700mW Mono Audio Amplifier | Texas Instruments
TPA321DGN

TPA321DGN - 700mW Mono Audio Amplifier | Texas Instruments

The Texas Instruments TPA321DGN is a 700 mW mono, analog-input Class-AB audio power amplifier with differential inputs, supplied in an 8-pin HVSSOP package. It is designed for low-voltage audio systems operating from a 5 V-class supply, with operation also specified for 3.3 V systems. The device combines a mono output stage with differential signal handling, allowing a balanced or bridged signal-chain arrangement while supporting compact speaker-driving designs. An audio power amplifier is an integrated circuit that takes a low-level analog audio signal and supplies the voltage and current needed to drive a loudspeaker. The TPA321 belongs to the Class-AB linear-amplifier family, a topology commonly used for small speakers because it provides continuous analog amplification without requiring an external Class-D switching modulator. Within the broader hierarchy, it is an audio amplifier IC, analog amplifier, and power-management semiconductor intended for portable and embedded audio equipment. The principal product characteristics are its 700 mW maximum output-power capability, mono Class-AB output architecture, and differential analog inputs. According to the Texas Instruments TPA321 product page, the amplifier is specified for 3.3 V and 5 V operation, providing compatibility with common portable-device supply rails. Its differential input arrangement can improve rejection of unwanted common-mode signals when the source and return paths are balanced, although the complete signal-chain topology must still be evaluated for noise, offset, gain, and channel count. The TPA321 uses an analog Class-AB output stage rather than a switching amplifier. This architecture avoids the modulator, switching node, and associated electromagnetic-interference considerations required by Class-D solutions. The trade-off is conventional linear-amplifier behavior: supply-current demand increases with output power, and efficiency is lower than that of a comparable Class-D converter when the signal is large. The provided manufacturer and distributor information does not expose detailed internal architecture, thermal resistance, or full frequency-response limits, so those values require confirmation in the manufacturer datasheet. Typical uses include compact mono speakers in portable audio products, small consumer appliances, auxiliary audio modules, and embedded systems accepting analog input. The TPA321DGN is particularly relevant when one amplified channel is sufficient and an 8-pin surface-mount footprint is preferred over a larger power-amplifier package. Its 700 mW rating supports appropriately selected low-impedance loudspeakers, while the 3.3 V and 5 V operating focus aligns it with modern portable and embedded systems rather than high-voltage automotive audio. Designers should verify the speaker impedance, minimum load, supply range, output-power derating, and thermal performance under worst-case audio duty cycle before production use. Input and output grounding should be planned to minimize channel offset, popping, and feedback. Because the package is a compact HVSSOP, copper area and thermal-path design are important when the amplifier operates continuously near its stated output-power capability. This product record combines the verified Texas Instruments product description, distributor package and ordering information, and an engineering-oriented comparison with a documented pin-compatible-class candidate. It also distinguishes verified ratings from parameters that still require direct datasheet confirmation, helping engineers evaluate procurement, PCB reuse, and audio-system suitability without relying solely on a distributor listing.

طلب عرض سعر اتصل بنا
TPA321DGNR - 700mW Mono Audio Amplifier | Texas Instruments (Tape & Reel)
TPA321DGNR

TPA321DGNR - 700mW Mono Audio Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments TPA321DGNR is a 700 mW mono, analog-input Class-AB audio power amplifier with differential inputs, supplied in an 8-pin HVSSOP package. It is designed for low-voltage audio systems operating from a 5 V-class supply, with operation also specified for 3.3 V systems. The device combines a mono output stage with differential signal handling, allowing a balanced or bridged signal-chain arrangement while supporting compact speaker-driving designs. An audio power amplifier is an integrated circuit that takes a low-level analog audio signal and supplies the voltage and current needed to drive a loudspeaker. The TPA321 belongs to the Class-AB linear-amplifier family, a topology commonly used for small speakers because it provides continuous analog amplification without requiring an external Class-D switching modulator. Within the broader hierarchy, it is an audio amplifier IC, analog amplifier, and power-management semiconductor intended for portable and embedded audio equipment. The principal product characteristics are its 700 mW maximum output-power capability, mono Class-AB output architecture, and differential analog inputs. According to the Texas Instruments TPA321 product page, the amplifier is specified for 3.3 V and 5 V operation, providing compatibility with common portable-device supply rails. Its differential input arrangement can improve rejection of unwanted common-mode signals when the source and return paths are balanced, although the complete signal-chain topology must still be evaluated for noise, offset, gain, and channel count. The TPA321 uses an analog Class-AB output stage rather than a switching amplifier. This architecture avoids the modulator, switching node, and associated electromagnetic-interference considerations required by Class-D solutions. The trade-off is conventional linear-amplifier behavior: supply-current demand increases with output power, and efficiency is lower than that of a comparable Class-D converter when the signal is large. The provided manufacturer and distributor information does not expose detailed internal architecture, thermal resistance, or full frequency-response limits, so those values require confirmation in the manufacturer datasheet. Typical uses include compact mono speakers in portable audio products, small consumer appliances, auxiliary audio modules, and embedded systems accepting analog input. The TPA321DGNR is particularly relevant when one amplified channel is sufficient and an 8-pin surface-mount footprint is preferred over a larger power-amplifier package. Its 700 mW rating supports appropriately selected low-impedance loudspeakers, while the 3.3 V and 5 V operating focus aligns it with modern portable and embedded systems rather than high-voltage automotive audio. Designers should verify the speaker impedance, minimum load, supply range, output-power derating, and thermal performance under worst-case audio duty cycle before production use. Input and output grounding should be planned to minimize channel offset, popping, and feedback. Because the package is a compact HVSSOP, copper area and thermal-path design are important when the amplifier operates continuously near its stated output-power capability. This product record combines the verified Texas Instruments product description, distributor package and ordering information, and an engineering-oriented comparison with a documented pin-compatible-class candidate. It also distinguishes verified ratings from parameters that still require direct datasheet confirmation, helping engineers evaluate procurement, PCB reuse, and audio-system suitability without relying solely on a distributor listing.

طلب عرض سعر اتصل بنا
TPA3220DDW - 60W Stereo Class-D Amplifier | Texas Instruments
TPA3220DDW

TPA3220DDW - 60W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TPA3220DDW is an analog-input Class-D audio amplifier rated for 60 W stereo output and 110 W mono output, operating from 7 V to 32 V in a 44-pin HTSSOP (DDW) package with exposed pad. It accepts single-ended or differential analog inputs up to 2 V RMS, with selectable gains of 18 dB, 24 dB, 30 dB, and 34 dB. A Class-D amplifier is a switching audio-output stage whose efficiency is substantially higher than that of a conventional linear amplifier at comparable output power. Its hierarchy extends from audio amplifiers to power-management semiconductors. The TPA3220 family combines analog input conditioning, a feedback-controlled Class-D output stage, thermal protection, and efficient power conversion in one device, reducing the number of external components required for a compact audio output channel. Key features include greater than 90% efficiency, idle power below 0.25 W, standby power below 0.1 W, and a closed-loop feedback bandwidth extending to 100 kHz. Its optimized gate-drive design and 70 mΩ MOSFET output devices support efficient full-power operation. Four input-gain settings allow the same amplifier to accommodate different source levels without redesigning the analog front end. The TPA3220 supports both analog-differential (AD) modulation and low-idle-current HEAD modulation. AD operation provides conventional differential behavior, while HEAD modulation targets lower idle consumption when the amplifier is not delivering substantial audio power. The 100 kHz feedback bandwidth helps reduce distortion within the audio band, while the analog input interface supports both single-ended and differential signal sources. Typical applications include stereo speaker systems, mono subwoofer amplifiers, powered multimedia speakers, soundbars, home-audio receivers, television audio platforms, and compact consumer-audio products. The 7 V to 32 V supply range accommodates automotive and portable-system rails after the appropriate input filtering, protection, and power-conversion stages have been designed. For implementation, place the exposed-pad thermal interface and input/output capacitors according to the manufacturer layout guidance. Confirm the speaker load, thermal performance, analog gain, and filter selection before production. The manufacturer datasheet should be used to verify pin assignments, absolute maximum ratings, and exposed-pad land geometry.

طلب عرض سعر اتصل بنا
TPA3221DDV - 100W Stereo Class-D Amplifier | TI
TPA3221DDV

TPA3221DDV - 100W Stereo Class-D Amplifier | TI

The Texas Instruments TPA3221DDV is an analog-input Class-D audio power amplifier rated for 100 W stereo output or 200 W mono output from a 7 V to 32 V supply. It is packaged in a thermally enhanced 44-pin HTSSOP (DDV) package and operates from -40 °C to 85 °C. The device combines efficient Class-D output with analog signal input for compact, high-power audio systems. A Class-D audio amplifier is a switching power amplifier that uses a switching output stage to deliver audio energy with high efficiency. Within the broader hierarchy, it is an audio amplifier, power amplifier, analog signal-processing IC, and power-management semiconductor. Compared with a conventional linear audio amplifier, a Class-D stage can reduce waste heat while supporting higher output power within compact enclosures. The TPA3221DDV supports both stereo and mono operating arrangements. Its headline capabilities are 100 W per stereo channel, 200 W in mono operation, and a 7 V to 32 V supply range. Low-idle operation is specifically identified for the device, making it suitable for audio receivers, powered speakers, home-theater equipment, and automotive audio systems where standby efficiency matters. The amplifier uses analog input and closed-loop feedback. A bandwidth of up to 100 kHz is identified for the feedback architecture, while the product family is described as an HD-Audio Class-D amplifier. These characteristics place the TPA3221DDV in the family of high-power audio amplifier ICs intended for amplification of left, right, or bridged mono signals rather than low-level headphone or line-output devices. Typical applications include powered bookshelf and floor-standing speakers, compact home-theater receivers, soundbars, subwoofer amplifiers, and automotive audio head units. A 32 V maximum supply provides useful power headroom for high-output stages, while the 7 V lower limit supports conventional automotive and lower-voltage audio systems. The exposed-pad HTSSOP package is particularly important because sustained high-power output requires careful PCB heat spreading. The primary design consideration is thermal management. Place the exposed pad over a continuous copper area and minimize thermal vias and copper-keepout regions according to the manufacturer layout guidance. Power-supply decoupling must also be placed close to the device. Output-filter component selection and loudspeaker loading should be evaluated together because the Class-D topology and reactive speaker load influence amplifier stability. This page combines the manufacturer power ratings, package information, operating limits, pin-compatible family alternatives, application guidance, and practical layout considerations to support faster component selection and PCB design decisions.

طلب عرض سعر اتصل بنا
TPA3244DDW - 60W Stereo Class-D Amplifier | Texas Instruments
TPA3244DDW

TPA3244DDW - 60W Stereo Class-D Amplifier | Texas Instruments

The Texas Instruments TPA3244DDW is a high-performance, 60 W stereo Class-D audio power amplifier with 120 W mono capability, analog input, and pad-down construction in a 44-pin HTSSOP (DDW) package. It accepts a 12 V to 31.5 V supply, operates across a 0°C to 70°C temperature range, and uses Texas Instruments PurePath Ultra-HD technology to deliver premium sound quality with the efficiency of a Class-D output stage. A Class-D audio amplifier is a power-management IC that switches its output stage between active and inactive states, reducing the amount of energy dissipated compared with a conventional linear output stage. Within the audio-amplifier hierarchy, the TPA3244DDW combines an analog input interface, integrated power stages, speaker outputs, and thermal management in one package. This integration supports compact stereo and high-power mono designs without requiring discrete output transistors on the board. The principal feature is its 60 W stereo output rating, with the same device specified for operation as a 120 W mono amplifier. Analog input simplifies compatibility with conventional audio sources, while the 12 V to 31.5 V supply range accommodates common single-rail amplifier architectures. The pad-down HTSSOP package places the exposed thermal pad beneath the device so PCB copper can remove heat from the power stage. Its stated operating range is 0°C to 70°C, making it appropriate for indoor consumer and professional audio equipment where that environmental range is acceptable. PurePath Ultra-HD technology distinguishes this amplifier from basic Class-D solutions by targeting low output distortion and high-quality audio reproduction. The integrated switching output stage avoids the continuous bipolar dissipation associated with linear amplifier output stages, although efficiency still depends on supply voltage, output power, load impedance, and thermal design. A low-impedance, low-noise supply is important because supply noise and instability can affect the power stage even when the audio input is clean. Typical uses include powered speakers, active bookshelf speakers, compact home-theater systems, soundbars, subwoofer power stages, and multimedia speaker enclosures. In stereo operation, the amplifier can drive two speaker channels from an analog source. In a bridged mono arrangement, its 120 W capability can serve a subwoofer or high-output monoblock. The 44-pin HTSSOP package requires careful PCB layout, adequate exposed-pad thermal copper, and a clean power-supply connection. Designers should follow the recommended application diagrams in the manufacturer datasheet, preserve the exposed-pad thermal path, and use the specified input and supply decoupling. Speaker wiring and power-supply connections must be sized for the intended output level. Stereo, bridged mono, and single-ended configurations have different terminal and load constraints, so confirm the selected topology before finalizing the board layout. This page combines the official device specifications with application guidance, packaging details, and a conservative drop-in assessment. It also distinguishes verified device facts from parameters that require confirmation from the manufacturer datasheet, helping engineers plan sourcing and hardware qualification without relying on assumptions.

طلب عرض سعر اتصل بنا
TPA3245DDV - 115W Class-D Amplifier | Texas Instruments
TPA3245DDV

TPA3245DDV - 115W Class-D Amplifier | Texas Instruments

The Texas Instruments TPA3245DDV is a 2-channel analog-input Class-D audio power amplifier rated for 115 W stereo output and 230 W mono output from a 12 V to 31.5 V supply, housed in a 44-pin HTSSOP package. It combines high output power with the efficiency advantages of Class-D amplification for premium audio systems. A Class-D audio amplifier is a power-management semiconductor that switches its output stage efficiently to reproduce an analog input signal at speaker-level voltage and current. The TPA3245 belongs to the amplifier IC hierarchy that includes analog power amplifiers, audio amplifiers, and Class-D output stages. Its two-channel architecture supports stereo operation, while its mono capability permits both channels to be combined for a higher-power single-channel configuration. The TPA3245DDV provides 115 W per channel in stereo mode and 230 W into a single channel in mono mode. Its 12 V to 31.5 V operating supply range accommodates higher-voltage audio systems, and its analog input architecture accommodates conventional line-level signals. The Class-D topology provides high efficiency while supporting the high output power associated with powered speakers, home-theater equipment, and professional audio amplification. The 44-pin HTSSOP package provides a compact surface-mount implementation for multi-channel audio products. The manufacturer identifies the TPA3245 as a high-performance amplifier designed to provide premium sound quality with efficient Class-D technology. Its 15 mA quiescent current helps limit standing consumption when the amplifier is active but not delivering significant output power. Typical uses include powered stereo speakers, home-theater amplifiers, soundbars, powered subwoofer platforms, and other high-output audio equipment. In a stereo design, each channel drives its assigned speaker section. In a bridged mono arrangement, the two output channels combine to deliver up to 230 W into one speaker load. Thermal design, output-filter selection, power-rail stability, and speaker-load compatibility determine practical performance. The design must also account for the full 12 V to 31.5 V supply range and maintain adequate PCB copper area for heat dissipation. Use the manufacturer datasheet pin description and application information when assigning connections and laying out the power stage. This product page combines the official device description, distributor identification, electrical highlights, application guidance, and verified replacement information. It also distinguishes an exact same-package ordering variant from packaging-only alternatives and identifies design parameters that require confirmation in the manufacturer datasheet before a PCB is released.

طلب عرض سعر اتصل بنا
TPA3255DDV - 315W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)
TPA3255DDV

TPA3255DDV - 315W Stereo Class-D Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments TPA3255DDV is a 315 W stereo, 600 W mono, analog-input Class-D audio power amplifier with an 18 V to 53.5 V supply range, supplied in a 44-pin HTSSOP DDV package. It is designed for high-power audio systems requiring efficient amplification and premium sound quality. The device supports two-channel stereo operation and can also be configured for mono use at higher output power. A Class-D audio amplifier is a switching power amplifier that uses transistor switching to deliver audio energy efficiently. In the broader hierarchy, a Class-D amplifier belongs to audio amplifiers, linear and nonlinear power amplifiers, and power-management semiconductor systems. Compared with a conventional linear audio amplifier, its switching architecture can reduce wasted power and heat while maintaining high output capability. The verified product information identifies 315 W stereo output, 600 W mono output, analog input, an 18 V to 53.5 V supply range, and a 44-pin HTSSOP package. The distributor listing also identifies the amplifier as a two-channel stereo Class-D device. These ratings make it suitable for professional audio, home-theater, public-address, multimedia, and other high-power sound systems where load capability and efficiency are important. Thermal design is central to using this amplifier because Class-D power stages can dissipate substantial heat at high output power. The DDV package provides a large thermal pad for board-level heat spreading, but the exact thermal resistance, output configuration details, protection thresholds, and application-specific limits must be taken from the manufacturer datasheet. The verified distributor information reports a 44-pin PowerTSSOP package and an operating-temperature range of 0 to 70 °C for the listed orderable part. Typical implementation uses analog audio inputs into the Class-D power stage, with speaker outputs driving stereo or bridged mono configurations. The amplifier is appropriate when the system supply is in the verified 18 V to 53.5 V range and the load is compatible with the manufacturer-defined output power conditions. Board layout, speaker wiring, grounding, thermal management, and protection circuitry should follow the TI datasheet and evaluation-board guidance. This product page combines verified Texas Instruments specifications, distributor package and sourcing information, application guidance, and verified cross-reference results. It distinguishes the high-power TPA3255DDV from lower-power or functionally similar parts that may use different packages or pin configurations.

طلب عرض سعر اتصل بنا