المنتجات (44,000+)

TS931BID - Micropower Rail-to-Rail Op Amp | STMicroelectronics
TS931BID

TS931BID - Micropower Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS931BID is a single-circuit, micropower, rail-to-rail operational amplifier with a 2.7 V to 10 V supply range, packaged in an 8-pin SOIC. It is designed for general-purpose signal conditioning where low power consumption, rail-to-rail output capability, and operation from low-voltage supplies are important. The TS931BID combines a listed quiescent current of 0.0003 uA, input bias current of 1 pA, and a gain-bandwidth product of 100 kHz. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The rail-to-rail output architecture allows the output signal to approach the supply rails more closely than a conventional amplifier with limited output swing. This makes the TS931BID useful for portable instruments, battery-powered sensors, low-voltage industrial controls, and other embedded systems that require amplification without a high-power supply. Key characteristics include one amplifier circuit, rail-to-rail output operation, a 2.7 V minimum supply voltage, and a 10 V maximum supply voltage. The low 0.0003 uA quiescent-current figure supports energy-conscious designs, while the 1 pA input-bias-current specification reduces input-loading effects in high-impedance measurement paths. A listed 55 dB gain-bandwidth-related figure and 100 kHz bandwidth suit low-to-moderate-frequency precision signal applications. The TS931BID belongs to the STMicroelectronics TS931 family of low-power operational amplifiers. Its 8-SOIC package supports conventional surface-mount assembly and provides a practical option for designs requiring a single amplifier in a small, standard package. Because the device operates from a 2.7 V supply, system-level signal ranges should be checked against the input common-mode and output-swing limits in the manufacturer datasheet. Typical uses include low-voltage sensor interfaces, portable measurement equipment, battery-operated data-acquisition modules, industrial process monitoring, and embedded control systems. In a sensor interface, the amplifier can increase the usable signal level before an ADC samples it. In a portable instrument, its low quiescent current helps limit standby consumption. The relatively modest 100 kHz bandwidth favors precision and low-frequency measurements rather than high-speed signal processing. PCB design should place input and feedback components close to the amplifier pins and maintain short, low-impedance traces to reduce noise pickup and parasitic feedback. Decoupling capacitors should connect directly between the supply and ground pins. Before substituting the TS931BID, verify supply voltage, input common-mode range, output swing, stability with the selected load capacitance, noise performance, and the exact pin assignment. This page combines the identified TS931BID electrical characteristics, package information, sourcing context, and practical design guidance. It also organizes same-family alternatives and a parameter comparison to help engineers determine whether the device fits the required footprint, voltage range, bandwidth, and power budget.

طلب عرض سعر اتصل بنا
TS931BILT - 100kHz Rail-to-Rail Micropower Op Amp | STMicroelectronics
TS931BILT

TS931BILT - 100kHz Rail-to-Rail Micropower Op Amp | STMicroelectronics

The STMicroelectronics TS931BILT is a single-channel CMOS operational amplifier in a SOT-23-5 package, featuring rail-to-rail output swing, micropower consumption, and operation down to 2.7 V single supply. As a member of the TS93x family (single/dual/quad variants), it delivers 100 kHz gain-bandwidth product while drawing only a few microamps of quiescent current, making it an excellent choice for battery-powered and portable applications. An operational amplifier (op-amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and, typically, a single-ended output. Within the broader signal-conditioning hierarchy, op-amps sit between transducers/ADC front ends and downstream digital processing; rail-to-rail output variants extend the usable output swing to nearly both supply rails, maximizing dynamic range in low-voltage systems. Micropower CMOS op-amps like the TS931BILT optimize this topology for low-Iq operation, trading GBW and slew rate for extended battery life in handheld, IoT, and remote-sensor designs. Key specifications include a 2.7 V to 10 V supply range, 100 kHz GBW, rail-to-rail output (reaching 2.9 Vpp with RL = 100 kΩ at 3 V supply), CMOS input stage, and an operating temperature range of -40 °C to +105 °C. The SOT-23-5 package is among the smallest standard op-amp footprints, enabling compact PCB layouts in space-constrained designs. Architecturally, the TS931BILT uses a CMOS input stage with a class-AB output stage to deliver rail-to-rail output swing at low quiescent current. The 'B' suffix denotes the enhanced second-generation variant, offering improved offset and noise compared with the original TS931, while the 'I' in 'ILT' indicates the industrial temperature grade (-40 °C to +105 °C). Typical applications include battery-powered instrumentation, portable medical devices, sensor signal conditioning, active filters, and transducer interfaces. The micropower Iq makes it ideal for always-on circuits where sleep current must be minimized. When designing with this op-amp, note that the CMOS inputs have lower bias current than bipolar alternatives but may exhibit higher leakage at elevated temperatures. Decouple the supply with a 100 nF ceramic capacitor placed close to the VCC pin to suppress noise. This page synthesizes distributor pricing, drop-in alternatives within the same SOT-23-5 footprint, and practical design notes that go beyond the manufacturer datasheet, helping engineers select the right op-amp quickly.

طلب عرض سعر اتصل بنا
TS931ID - 100kHz Rail-to-Rail Op Amp | STMicroelectronics
TS931ID

TS931ID - 100kHz Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS931ID is a single-amplifier, general-purpose operational amplifier with a 100 kHz gain-bandwidth product, rail-to-rail output operation, and a 2.7 V minimum supply voltage, packaged in an 8-pin SOIC. It operates from single 2.7 V to 10 V supplies, consumes approximately 20 µA, and provides an extremely low typical input bias current of 1 pA. The device is suited to portable instrumentation, low-power signal conditioning, buffering, and general analog signal-processing applications. An operational amplifier, or op amp, is an analog integrated circuit that provides high open-loop gain and feedback control for amplification, filtering, comparison, buffering, and signal conversion. The TS93x family belongs to the broader operational-amplifier hierarchy, which includes instrumentation, rail-to-rail, micropower, and precision amplifier categories. Rail-to-rail output operation allows the TS931ID to approach its supply-voltage limits at the output, improving dynamic range in low-voltage systems where usable signal headroom is limited. The TS931ID provides several characteristics suited to compact analog designs. Its 100 kHz gain-bandwidth product supports moderate-frequency amplification and feedback networks, while the approximately 20 µA supply consumption suits battery-operated equipment. The 1 pA typical input bias current minimizes disturbance to high-impedance sources. According to the available STMicroelectronics datasheet material, the device can reach a 2.9 Vpp output swing with a 100 kΩ load when supplied at 3 V. The TS931ID uses CMOS inputs and includes ESD protection, making it appropriate for low-leakage analog interfaces. Rail-to-rail output swing improves usable signal range near the positive or negative supply rail, but input common-mode behavior, output-current capability, stability, and drive into capacitive loads must still be checked against the complete operating condition. The single-amplifier configuration also reduces board area when one independent analog channel is required rather than a dual or quad device. Typical uses include low-power sensor conditioning, portable measurement systems, analog buffering, low-current-to-voltage conversion stages, and small-signal control circuits. Its combination of a 2.7 V minimum supply, 20 µA-class consumption, and 100 kHz bandwidth is particularly relevant to battery-powered instrumentation. The 8-pin SOIC package supports conventional surface-mount assembly and is convenient for prototypes, repair, and mixed analog or mixed-signal boards. Designers should account for output headroom when driving loads, verify stability with the selected feedback network and load capacitance, and route sensitive input traces away from switching nodes. Input and output bypassing must follow the manufacturer recommendations. Because the verified source set does not provide complete offset, slew-rate, common-mode-range, and absolute-maximum-rating tables, those values should be confirmed in the official datasheet before a safety- or precision-critical design is released. This page consolidates the verified distributor specifications, package information, purchasing reference, family-level alternatives, and practical analog-design guidance. It also distinguishes documented values from parameters that still require direct confirmation from the manufacturer datasheet, helping engineers move from part selection to PCB implementation without presenting unverified figures as facts.

طلب عرض سعر اتصل بنا
TS932AIN - Dual 100 kHz Rail-to-Rail Op Amp | STMicroelectronics
TS932AIN

TS932AIN - Dual 100 kHz Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS932AIN is a dual general-purpose operational amplifier with rail-to-rail output, a 100 kHz gain-bandwidth product, and micropower operation, packaged in an 8-pin through-hole DIP. Each package contains two amplifier circuits, allowing a design to use two independent analog signal paths while retaining a compact, industry-standard footprint. An operational amplifier is a voltage-feedback analog IC that compares an amplified error signal with a feedback network to control its output. The TS932AIN belongs to the dual operational amplifier category, combining two amplifier channels in one package. Its rail-to-rail output architecture is useful when signals must remain usable near the available supply limits, while its micropower design suits battery-operated and low-power instrumentation. The principal features of the TS932AIN include two amplifier circuits, rail-to-rail output, a 100 kHz gain-bandwidth product, and an industrial temperature grade. The 100 kHz bandwidth supports general-purpose low-frequency signal conditioning rather than demanding high-speed waveform applications. The through-hole 8-DIP construction supports prototyping, repair, legacy equipment, and industrial control boards where leaded packages remain convenient to assemble. The TS932AIN is specified as a general-purpose amplifier rather than a precision or high-voltage part. Because the device uses an 8-pin DIP, it provides two complete amplifier channels with shared supply pins. Designers should verify the manufacturer's pin description and operating limits against the target circuit before substituting it into safety-critical, automotive, or medical equipment. Typical uses include low-frequency sensor conditioning, current-loop and voltage-amplifier stages, industrial control interfaces, audio preamplification, and portable measurement systems. Its dual-channel configuration can reduce component count when two similar low-frequency signals must be conditioned. The 100 kHz gain-bandwidth rating also makes it appropriate for slow control loops and modest instrumentation bandwidth, rather than pulse or data-conversion applications demanding much higher bandwidth. For a new design, check input bias current, output swing, supply range, noise, and stability requirements against the manufacturer datasheet before committing to the TS932AIN. Place bypass capacitors close to the supply pins, keep feedback paths compact, and observe the standard dual-op-amp pin arrangement shown below. This page also identifies package and function alternatives while clearly separating true PCB drop-ins from options that require a layout change.

طلب عرض سعر اتصل بنا
TS932BIN - Dual 20uA Rail-to-Rail Op Amp | STMicroelectronics
TS932BIN

TS932BIN - Dual 20uA Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS932BIN is a dual, micropower, rail-to-rail operational amplifier with a 2.7 V to 10 V supply range, 20 uA supply current per channel, and an 8-DIP package. The two amplifiers are intended for low-voltage instrumentation and general-purpose signal-conditioning applications. Their rail-to-rail output stage supports operation near the supply rails, while the low 20 uA per-channel current supports battery-powered and portable equipment. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The broader hierarchy is operational amplifier -> analog amplifier IC -> integrated circuit. The TS932BIN belongs to the micropower operational-amplifier family, where low quiescent current and rail-to-rail output capability are the principal selection criteria. Its dual-channel configuration also reduces component count when two independent gain stages are required. Key electrical characteristics include a 2.7 V to 10 V operating supply, approximately 20 uA supply current per channel, up to 5 mA output current per channel, 1 pA input-bias current, and 55 dB nominal gain-bandwidth information. The device also supports rail-to-rail output operation and is specified for low-voltage applications. These characteristics make it appropriate for portable measurement, current sensing, and sensor-conditioning circuits where a conventional high-current amplifier would consume unnecessary power. The TS932BIN uses a rail-to-rail output architecture rather than relying exclusively on conventional source or sink output stages. This allows output signals to approach both supply rails more closely, improving usable dynamic range in low-voltage systems. Because it is a dual amplifier, both channels share the same supply pins while retaining independent input and output connections. Engineering designs must still account for common-mode-range limits, output-current limits, input-bias-current effects, and the voltage drop needed to drive the connected load. Typical applications include battery-powered sensor interfaces, portable instrumentation, low-current transducers, industrial control signals, and general dual-stage analog signal conditioning. Two amplifiers can be used for independent amplifier, buffer, comparator, or active-filter functions. For precision measurement systems, the circuit designer should verify input offset voltage, common-mode rejection, noise, and bias-current error against the complete signal-chain requirements rather than treating the amplifier as an ideal component. A practical design consideration is to bypass each supply pin close to the device with local ceramic decoupling and route analog inputs away from switching-current paths. The operating range of 2.7 V to 10 V leaves design margin for both low-voltage portable systems and higher-voltage industrial rails. Output loading and feedback-network values should be checked against the 5 mA per-channel output-current capability. This page combines the TS932BIN electrical characteristics, package information, pin assignment, engineering alternatives, comparison parameters, and application guidance into a selection reference for dual micropower operational-amplifier designs.

طلب عرض سعر اتصل بنا
TS932ID - Dual 100 kHz Rail-to-Rail Op Amp | STMicroelectronics
TS932ID

TS932ID - Dual 100 kHz Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS932ID is a dual, rail-to-rail-output micropower operational amplifier with a 100 kHz gain-bandwidth product, 0.05 V/µs slew rate, and a 2.7 V to 10 V supply-voltage range. The device is supplied in an 8-pin SOIC package and is intended for low-power, low-frequency signal conditioning where low supply current and CMOS input characteristics are important. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, compare, and filter signals. The TS93x family belongs to the amplifier IC hierarchy, where rail-to-rail output stages allow an output voltage to approach the supply rails. This capability makes the TS932ID suitable for battery-powered sensors, portable instrumentation, and low-voltage analog interfaces. Key characteristics include a 100 kHz gain-bandwidth product, 0.05 V/µs slew rate, and typical supply-current consumption of 20 µA. The output can reach 2.9 Vpp when supplied from 3 V with a 100 kΩ load. The TS93x series also features CMOS inputs, ultra-low input bias current of approximately 1 pA, and ESD protection. These characteristics favor high-impedance sources and energy-limited systems rather than demanding high-speed or high-precision instrumentation. The TS932ID is a dual amplifier, allowing two independent signal paths in one package. Its rail-to-rail output architecture simplifies signal conditioning near low supply voltages, while its micropower operation reduces the burden on batteries or harvested-energy supplies. The 100 kHz bandwidth is adequate for audio-frequency, sensing, and general-purpose feedback-control loops, but it is not intended for high-frequency filtering, video amplification, or communications waveform processing. Typical applications include battery-operated sensor conditioning, low-current comparator or threshold functions, portable measurement modules, low-frequency active filters, analog sensor interfaces, and general-purpose buffering. In each case, the device provides two amplifier channels in a compact 8-pin SOIC while consuming approximately 20 µA under the stated family conditions. Designers should verify output load, input common-mode range, output swing, noise, offset, stability, and operating-temperature limits against the manufacturer datasheet before release. Decoupling capacitors should be placed close to the supply pins, and feedback-network components should be selected with practical bias-current and leakage considerations. This page consolidates the verified distributor information, manufacturer-family characteristics, package details, application guidance, and substitution limitations for TS932ID. It also distinguishes documented drop-in options from unsupported cross-package or functional substitutes so engineers can make a traceable replacement decision.

طلب عرض سعر اتصل بنا
TS932IDT - Dual Micropower RRO Op Amp | STMicroelectronics
TS932IDT

TS932IDT - Dual Micropower RRO Op Amp | STMicroelectronics

STMicroelectronics TS932IDT is a dual, rail-to-rail operational amplifier with CMOS inputs, a typical supply current of 20 uA, and a gain-bandwidth product of 100 kHz. It operates from supply voltages as low as 2.7 V and is packaged in an 8-pin SOIC. The device is intended for low-power, signal-conditioning, and battery-operated circuits. A rail-to-rail operational amplifier is an amplifier whose input and output voltage ranges can extend close to the supply rails. This capability helps preserve signal range in low-voltage systems where conventional amplifiers would clip signals near ground or the positive supply. The TS932 belongs to the operational-amplifier hierarchy, combining low quiescent consumption, CMOS input capability, and rail-to-rail operation in a compact SOIC-8 package. The TS932IDT provides two amplifier circuits in one package. According to the STMicroelectronics manufacturer datasheet, the TS93x series can operate with voltages as low as 2.7 V and reaches a 2.9 Vpp output swing with a 100 kΩ load when supplied at 3 V. Typical consumption is only 20 uA, making the dual amplifier suitable for portable instrumentation and other systems where supply efficiency and signal headroom are important. Its CMOS inputs support low-bias operation, while the 100 kHz gain-bandwidth product suits general-purpose low-frequency amplification rather than high-speed signal chains. The rail-to-rail output also improves usable output range near the supply limits. These characteristics make the device relevant to sensor interfaces, battery-powered measurement systems, audio control circuits, and low-power industrial electronics. Typical uses include buffering sensor outputs, amplifying low-level analog signals, and providing two independent amplifier channels in one package. Designers should account for the 100 kHz bandwidth when choosing feedback resistors and gain settings. High-gain configurations also require attention to input offset, bias current, noise, and stability. Use the TS932IDT when a dual amplifier, low quiescent current, and rail-to-rail operation are required in a compact SOIC-8 footprint. Confirm output loading, capacitive loads, supply range, and required bandwidth against the manufacturer datasheet before finalizing a precision or high-gain design. This product page combines manufacturer specifications, sourcing guidance, drop-in replacement analysis, and practical circuit-design notes to support faster component evaluation and PCB-level implementation.

طلب عرض سعر اتصل بنا
TS932IN - Dual 2.7V Rail-to-Rail Op Amp | STMicroelectronics
TS932IN

TS932IN - Dual 2.7V Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS932IN is a dual, general-purpose operational amplifier designed for low-voltage systems operating from 2.7 V. The device uses rail-to-rail output stages and is specified to reach a 2.9 Vpp output swing with a 100 kΩ load when supplied from 3 V. It is packaged for through-hole assembly in an 8-pin Mini DIP package. The TS932IN combines two amplifier channels, low-voltage operation, and rail-to-rail output capability in one compact IC, making it useful for sensor conditioning, portable instrumentation, audio signal processing, and general analog signal-chain designs. An operational amplifier is an analog integrated circuit that compares two input voltages and amplifies the difference between them. It belongs to the amplifier IC hierarchy and supports feedback, filtering, buffering, level conversion, and closed-loop control functions. The TS932IN is a dual amplifier, so two independent signal-processing channels are available in one package. Its rail-to-rail output stage is particularly useful when the required output signal must approach the available supply-rail limits. The primary confirmed features of the TS932IN include operation down to 2.7 V, dual-circuit construction, rail-to-rail output behavior, and a 2.9 Vpp output swing at 3 V supply with a 100 kΩ load. This combination suits battery-powered and low-voltage embedded systems where headroom is limited. Because the output can operate close to the supply rails, designers can increase usable signal range without requiring a substantially higher supply voltage. In dual-signal applications, the TS932IN can process one channel as an active filter and the other as a buffer or gain stage. Symmetrical device construction helps simplify PCB planning in instrumentation, audio, communications, and industrial control products. Its through-hole Mini DIP package also remains convenient for prototyping, educational platforms, repair assemblies, and designs assembled with conventional through-hole insertion rather than fine-pitch surface-mount automation. Typical applications include sensor-signal conditioning, low-voltage audio processing, joystick and control interfaces, ADC input drivers, active filters, and general-purpose dual-channel analog amplification. In a sensor interface, one amplifier can scale or invert a sensor output while the second channel can provide buffering for an ADC. In an audio preamplifier, the rail-to-rail outputs can support low-amplitude signals when the system operates near the lower supply limit. A primary design consideration is output loading. The stated 2.9 Vpp swing applies to a 100 kΩ load, so heavier loads can reduce usable output range and alter distortion or stability behavior. PCB implementations should keep input and feedback paths short, place compensation or decoupling components close to their associated pins, and provide adequate ground return paths. Engineers should also review the complete manufacturer datasheet for input common-mode limits, output-current capability, noise, bandwidth, and stability requirements. This product overview combines the verified operating envelope, package identity, and application-focused engineering guidance with a side-by-side view of potential replacements. It also highlights where engineers must confirm pin compatibility, load conditions, and lifecycle requirements before approving a substitution or redesigning an existing 8-pin Mini DIP layout.

طلب عرض سعر اتصل بنا
TS934ID - 4-Channel 2.7V R-R Micropower Op Amp | STMicroelectronics
TS934ID

TS934ID - 4-Channel 2.7V R-R Micropower Op Amp | STMicroelectronics

The STMicroelectronics TS934ID is a quad, rail-to-rail output, micropower operational amplifier designed for low-voltage signal conditioning and battery-powered systems. It contains four amplifiers in a 14-pin SOIC package, operates from 2.7V to 10V, supports single-supply operation, and is specified for a 100kHz gain-bandwidth product. The device combines a typical 20uA supply current with CMOS inputs, ultra-low input bias current of 1pA, and rail-to-rail output voltage swing. According to the manufacturer datasheet family information, the TS93x series is intended for portable instrumentation, sensor interfaces, and general-purpose analog signal processing. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs while providing high input impedance and low output impedance. The TS934ID belongs to the operational-amplifier hierarchy, which includes general-purpose amplifier ICs, micropower amplifiers, rail-to-rail amplifiers, and CMOS-input analog ICs. Its four integrated channels reduce the number of packages required when several low-frequency signals must be conditioned in the same system. The principal features are the 2.7V minimum supply voltage, 10V maximum supply voltage, 100kHz bandwidth, 0.05V/us slew rate, and approximately 20uA typical supply consumption described for the TS93x family. The output stage can reach 2.9Vpp with a 100kohm load when supplied from 3V, making the amplifier suitable for modest-swing signals in low-voltage systems. CMOS inputs minimize input bias current, which is advantageous when the source impedance is high. The TS934ID is not intended as a high-speed, high-voltage, or precision replacement for every general-purpose quad amplifier. Its 100kHz bandwidth and micropower bias favor portable and instrumentation applications over wideband signal chains. Designers should verify output swing, common-mode range, noise, offset, stability, and load capability against the complete manufacturer datasheet before using it with unusual source impedances, capacitive loads, or rail-to-rail input signals. Typical uses include battery-powered sensor conditioning, portable measurement equipment, industrial transducers, audio and communications interface circuits, and general 3V instrumentation. The 14-SOIC package is suitable for conventional through-hole PCB assembly and automated manufacturing. Because the device is a four-channel amplifier, one package can serve multiple independent amplifier sections in a compact analog front end. A key design consideration is power budgeting. The low supply current supports battery-operated systems, but the output still requires a stable supply and suitable bypass capacitance. The amplifier should be operated within the specified supply range and load conditions, and its output should not be used as a power-stage output. Pin assignments, common-mode behavior, and package details should be taken directly from the STMicroelectronics datasheet and pinout diagram. This page combines verified distributor and manufacturer-linked information, drop-in comparison candidates, pricing fields, application guidance, and practical design notes to support faster component selection and PCB planning.

طلب عرض سعر اتصل بنا
TS934IDT - Quad R-R Operational Amplifier | STMicroelectronics
TS934IDT

TS934IDT - Quad R-R Operational Amplifier | STMicroelectronics

STMicroelectronics TS934IDT is a four-circuit, rail-to-rail operational amplifier packaged in a 14-pin small-outline SOIC. It operates from 2.7 V to 10 V, supports a gain-bandwidth product of 100 kHz, and provides an input bias current of 1 pA with a typical channel current of 20 uA. The device is intended for low-power instrumentation, sensor-conditioning, buffer, and general-purpose analog signal-processing circuits. A rail-to-rail operational amplifier is an analog amplifier whose input and output stages can operate near the positive and negative supply rails. It belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, general-purpose amplifiers, and analog signal-chain ICs. This broad operating range makes the amplifier useful when signals can approach either supply rail, although actual input and output swing limits remain dependent on load conditions and supply voltage. The TS93x family combines four amplifiers in one package, reducing board area compared with discrete single or dual devices. Key characteristics include 5 mA of current consumption per channel, 55 dB instrumentation-amplifier performance as characterized by the product listing, and approximately 1 pA input bias current. At a 3 V supply, the series can produce a 2.9 Vpp output swing with a 100 kohm load, making it useful in low-voltage, low-power systems. The TS934IDT uses a 14-SO package and is specified for a 2.7 V to 10 V supply range. Its 100 kHz gain-bandwidth product is appropriate for slowly varying sensor signals, feedback-control loops, and analog measurement blocks rather than high-speed waveform or communications channels. Because all four amplifiers share one package, designers must account for common supply routing, thermal behavior, grounding, and channel-to-channel consistency during layout. Typical applications include portable sensor interfaces, low-voltage data acquisition, battery-powered measurement instruments, transducer conditioning, and general analog buffering. Four integrated amplifiers can be assigned to differential sensor inputs, level shifting, active filtering, or gain stages, although applications requiring high precision, high speed, or very low offset voltage should verify those limits against the manufacturer's electrical characteristics. When designing a board around the TS934IDT, place decoupling capacitors close to the supply pins and route the ground return directly to the device ground. Keep sensitive input traces away from switching nodes and high-current return paths. Because the amplifier can operate close to the supply rails, verify the actual input common-mode and output swing limits for the selected supply, load, and temperature before relying on full rail-to-rail behavior. This page organizes the confirmed electrical characteristics, package information, application guidance, design notes, and compatible family references for faster engineering evaluation. It also identifies which parameters require confirmation from the STMicroelectronics datasheet before a production design is released.

طلب عرض سعر اتصل بنا
TS934IN - Dual Micropower RRO Op Amp | STMicroelectronics
TS934IN

TS934IN - Dual Micropower RRO Op Amp | STMicroelectronics

The STMicroelectronics TS934IN is a dual, rail-to-rail output, micropower operational amplifier with CMOS inputs, supplied in a 14-pin DIP package. Its key characteristics are low supply current of 20 µA, operation from a 2.7 V single supply up to 10 V, a 100 kHz gain-bandwidth product, and an input bias current as low as 1 pA. The TS934IN is intended for low-voltage, low-power analog signal-conditioning circuits. An operational amplifier is an active analog integrated circuit that uses high open-loop gain to amplify small voltage differences. The TS934IN belongs to the operational-amplifier hierarchy of analog ICs, with rail-to-rail output swing and CMOS input characteristics. Its micropower operating current makes it suitable for battery-powered equipment, portable instruments, sensor interfaces, and low-power control systems where every microamp of supply demand affects battery life. The TS934 family provides rail-to-rail output swing, single-supply operation, CMOS inputs, ultra-low input bias current, and ESD protection. The TS934IN is identified as a general-purpose, two-circuit amplifier in a 14-DIP package. The 100 kHz gain-bandwidth product is appropriate for low-frequency buffering, amplification, filtering, and thresholding rather than high-speed signal processing. Its CMOS input stage is particularly useful when measuring high-impedance sources because input bias current is minimized. The TS934IN can operate from 2.7 V supplies, helping designers reduce the power requirements of portable systems. The manufacturer describes a 2.9 Vpp output swing with a 100 kΩ load when supplied from 2.7 V. This specification should be considered when the signal must approach the supply rails, especially for low-voltage sensor signals where headroom is limited. Typical uses include battery-powered sensor conditioning, portable measurement equipment, audio and control interfaces, low-frequency active filters, and general-purpose dual-amplifier signal paths. Because the device is a dual amplifier, both channels can be used in a single circuit when the application does not require independent supply sequencing. A key design consideration is to verify input common-mode range, output swing, stability, and load behavior against the manufacturer datasheet before using the amplifier near the supply limits. Decoupling capacitors should be placed close to the supply pins, and the unused channel inputs should be configured according to the recommended application circuit. This page combines the TS934IN technical identity with application guidance, comparison criteria, and practical design notes for engineers.

طلب عرض سعر اتصل بنا
TS941AID - Rail-to-Rail Micropower Op Amp | STMicroelectronics
TS941AID

TS941AID - Rail-to-Rail Micropower Op Amp | STMicroelectronics

The STMicroelectronics TS941AID is a single-circuit, rail-to-rail micropower operational amplifier packaged in an 8-pin SOIC. It is designed for general-purpose signal conditioning in low-voltage systems where output swing, low-power operation and compact surface-mount construction are important. The device is identified as an instrumentation, operational-amplifier and buffer-amplifier IC. Operational amplifiers are analog signal-processing devices that amplify the difference between two input voltages. A rail-to-rail output amplifier can approach its positive and negative supply rails more closely than a conventional amplifier, which helps preserve signal amplitude in low-voltage applications. The micropower operating class of the TS941AID makes it suitable for battery-operated and portable equipment where supply current must remain controlled. The TS941AID is a single amplifier in an 8-SOIC package, allowing designers to add analog conditioning without using a higher-channel-count package. Its rail-to-rail output characteristic is useful for sensor interfaces, low-voltage signal buffers, transducers and portable instrumentation. The manufacturer describes the family as output rail-to-rail micropower operational amplifiers. The TS941AID is intended for standard general-purpose analog designs rather than high-voltage or high-power applications. Its SOIC package is suitable for conventional PCB assembly, and its small footprint helps reduce board area compared with larger through-hole packages. Because the exact electrical limits depend on the supply voltage and operating conditions, the manufacturer datasheet should be used for input range, output swing, supply current, bandwidth, noise, stability and absolute-maximum-rating checks. Typical applications include low-voltage sensor interfaces, portable measurement systems, analog signal conditioning, battery-powered instrumentation and small embedded control systems. The single-amplifier arrangement also makes the TS941AID suitable when one channel is sufficient and a larger quad or dual amplifier would add unnecessary board area or cost. When designing a circuit around the TS941AID, check the datasheet pin description, input common-mode range, output swing, capacitive-load behavior and recommended operating region. Place bypass capacitors close to the supply pins and keep sensitive input routing short to reduce noise pickup and instability. This page combines manufacturer and distributor information with a practical focus on low-voltage analog design, package reuse, sourcing questions, pinout verification and drop-in replacement planning.

طلب عرض سعر اتصل بنا
TS941BID - 2.5V-10V Micropower Rail-to-Rail Op Amp | ST
TS941BID

TS941BID - 2.5V-10V Micropower Rail-to-Rail Op Amp | ST

The STMicroelectronics TS941BID is a single-circuit, rail-to-rail operational amplifier designed for low-voltage and low-power signal-conditioning systems. It operates from 2.5 V to 10 V, supports input and output signals extending toward the supply rails, and is specified across a -40°C to +85°C temperature range. The device is offered in an 8-pin SOIC package and is intended for instrumentation, buffering, sensing, and general-purpose analog applications. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. A rail-to-rail output stage can swing close to the positive and negative supply limits, making the amplifier useful when the usable signal range is restricted by a low supply voltage. The TS94x family belongs to the operational-amplifier hierarchy, combining generic analog signal amplification with micropower operation for battery-powered and portable equipment. The TS941BID provides a single amplifier in an 8-pin SOIC package. Its specified 2.5 V to 10 V operating range makes it appropriate for systems powered from low-voltage rails, while its -40°C to +85°C rated range supports industrial and extended-temperature environments. Rail-to-rail output operation increases the available output swing compared with a conventional amplifier whose output remains restricted below the supply rails. The product is described by STMicroelectronics as a micropower, rail-to-rail output operational amplifier. The architecture is intended for general-purpose analog conditioning rather than for high-speed differential signaling or precision instrumentation requiring unusually low offset and drift. Its low operating-voltage range enables operation from one-cell-compatible or low-voltage regulated rails, and the rail-to-rail output stage helps preserve signal range when the load current and output amplitude remain within the device's operating conditions. The SOIC package also supports conventional surface-mount assembly and easy routing on through-hole-compatible industrial boards. Typical uses include sensor-signal conditioning, low-voltage instrumentation, portable measurement systems, battery-powered sensing, analog monitoring, and general signal buffering. In a sensor interface, the amplifier can condition a low-amplitude signal before an ADC. In portable equipment, its micropower positioning helps reduce the energy required by the analog front end. It is also useful as a general-purpose rail-to-rail output buffer when the system operates from a 2.5 V to 10 V supply. Circuit design should account for input common-mode range, output swing, load capability, stability, supply bypassing, and noise performance before assigning the amplifier to a signal chain. Decoupling capacitors should be placed close to the supply pins, and the unused input should be connected to a defined reference potential rather than left floating. The manufacturer datasheet should be used to confirm the complete electrical limits, recommended operating conditions, and pin assignments. This product page combines the manufacturer family information with practical guidance for low-voltage analog design, including drop-in alternatives, application-oriented use cases, pin-package considerations, and design notes. These engineering notes help engineers evaluate the TS941BID alongside pin-compatible parts while maintaining clear separation between confirmed device characteristics and parameters that require confirmation from the full datasheet.

طلب عرض سعر اتصل بنا
TS941ID - 2.5-10V Rail-to-Rail Op Amp | STMicroelectronics
TS941ID

TS941ID - 2.5-10V Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS941ID is a single-circuit, general-purpose operational amplifier featuring a rail-to-rail output, 2.5 V to 10 V supply operation, and an 8-pin SOIC package. The device belongs to the TS94x micropower operational-amplifier family and is designed for instrumentation, signal buffering, and other low-voltage analog signal-chain applications. Its low-noise operation, high input impedance, and approximately 1 pA input-bias current support accurate handling of high-impedance sources while its rail-to-rail output improves dynamic range near the positive and negative supply rails. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, compare, and filter analog signals. The TS941ID sits within the operational-amplifier hierarchy and operates from a 2.5 V to 10 V supply, making it suitable for battery-powered, industrial-control, test-and-measurement, and portable equipment. Its rail-to-rail output stage allows the output voltage to approach the supply limits more closely than a conventional output stage, although the exact output swing and input common-mode behavior must be checked in the manufacturer datasheet for the selected supply voltage. Key features include a single amplifier configuration, rail-to-rail output, low-noise operation, high input impedance, and very low input-bias current of approximately 1 pA. The 2.5 V minimum supply voltage supports compact, low-energy systems, while the 10 V maximum provides compatibility with common industrial and laboratory supply rails. The manufacturer specifies operation over -40 °C to +85 °C, covering industrial temperature requirements without requiring an automotive-qualified variant. The TS941ID is intended for general-purpose precision signal conditioning rather than as a high-speed communications amplifier. Its micropower-oriented design is valuable when battery current is important, but the precise quiescent-current value should be taken from the manufacturer datasheet. The approximately 1 pA input-bias current is particularly useful with high-impedance sensors because it limits the DC current drawn through the source resistance and helps reduce input-offset errors. Typical applications include sensor-signal conditioning, low-current transimpedance buffering, portable instrumentation, industrial measurement, and general analog signal conditioning. In a transimpedance stage, the TS941ID can be paired with a suitable feedback resistor and compensation capacitor while its low input-bias current reduces bias-current-induced error. In instrumentation, it can buffer inputs before a higher-precision converter or provide gain around sensors whose output range does not use the complete supply span. When designing around the TS941ID, verify input common-mode range, output swing, unity-gain stability, noise, slew rate, and quiescent current against the actual load and supply conditions. Place input, feedback, and decoupling connections for low noise and stable feedback operation, and include adequate output-current margin for capacitive or resistive loads. The 8-pin SOIC footprint is convenient for conventional surface-mount assembly but is not as compact as the smallest QFN packages. This product page consolidates the verified manufacturer information, distributor availability references, family-level alternatives, parameter comparisons, and practical design guidance. It distinguishes confirmed TS941ID data from specifications that still require confirmation from the manufacturer datasheet, helping engineers identify the part faster without presenting unverified values as established facts.

USD $0.82 متوفر
TS941IDT - Micropower Rail-to-Rail Op Amp | STMicroelectronics
TS941IDT

TS941IDT - Micropower Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TS941IDT is a single-circuit, general-purpose operational amplifier characterized by micropower operation and rail-to-rail output voltage swing. It is packaged in an 8-pin SOIC and is identified as a 10 kHz device. The TS941IDT is intended for low-power signal-conditioning systems where a small amplifier package, low-power operation, and rail-to-rail output capability are useful. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The amplifier belongs to the voltage-feedback operational-amplifier family within the broader linear-amplifier and signal-processing IC hierarchy. Rail-to-rail output operation allows the output to approach the supply rails more closely than a conventional fixed-headroom amplifier, which can simplify signal-range calculations in low-voltage systems. Key characteristics of the TS941IDT include one amplifier circuit per package, micropower operation, rail-to-rail output behavior, and a gain-bandwidth product listed at 10 kHz. These attributes make the device applicable to sensor interfaces, low-level signal conditioning, portable instrumentation, and battery-powered products. Its 8-SOIC outline supports conventional surface-mount assembly while providing separate input, output, supply, and feedback connections. The TS94x-device family is intended for general-purpose precision signal amplification rather than high-speed waveform processing. The 10 kHz gain-bandwidth characteristic favors static or slowly varying signals, including sensor outputs, reference voltages, and slow feedback-control loops. Rail-to-rail output capability improves usable output range, while the single-amplifier package reduces board area when each signal channel requires only one active device. Typical uses include low-power sensor conditioning, portable measurement systems, analog control loops, and interface stages that operate from limited supply voltages. The device can also support low-current sensing and monitoring circuits where continued operation with low power consumption is valuable. Designers should confirm input common-mode range, output swing, supply limits, noise, offset, and stability requirements against the manufacturer datasheet before selecting it for a new signal chain. PCB implementation requires care around the feedback network and supply connections. Place input and output decoupling capacitors close to the device, keep feedback-loop routing compact, and provide a low-impedance ground return. Because the TS941IDT is optimized for micropower applications, component tolerances and leakage currents can influence bias-point accuracy, especially when sensing signals close to the supply rails. This page organizes the available TS941IDT technical information with an application-focused selection guide, drop-in replacement analysis, comparison data, and practical layout guidance. It is intended to help engineers determine whether the TS941IDT's package, bandwidth, rail-to-rail output behavior, and low-power orientation fit the target circuit before committing to a design.

طلب عرض سعر اتصل بنا
TS941ILT - RRIO Micropower Op Amp, SOT-23-5 | STMicroelectronics
TS941ILT

TS941ILT - RRIO Micropower Op Amp, SOT-23-5 | STMicroelectronics

STMicroelectronics TS941ILT is a single-amplifier, rail-to-rail input and output operational amplifier designed for low-power signal conditioning from 2.5 V to 10 V. It is packaged in the compact SOT-23-5 surface-mount package and is specified for operation from -40°C to +85°C. The TS94x family combines general-purpose signal amplification with rail-to-rail operation, allowing the amplifier to process signals near the positive and negative supply rails without requiring a separate mid-supply bias. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The TS941 belongs to the operational-amplifier hierarchy, where it serves as a low-power analog signal-conditioning building block for sensor interfaces, voltage buffers, filters, and low-frequency control circuits. Rail-to-rail input and output behavior is particularly useful when the available signal range occupies much of the supply voltage. The TS941ILT is a single-circuit device, allowing a compact amplifier layout without the extra channel area of dual or quad alternatives. Its 2.5 V to 10 V operating range supports low-voltage battery-powered systems as well as conventional low-voltage analog circuits. The -40°C to +85°C industrial temperature range provides useful margin for industrial, automotive-adjacent, communications, and instrumentation equipment when the complete system requirements permit that temperature range. STMicroelectronics describes the TS94x series as micropower operational amplifiers, making the family relevant to designs in which amplifier current consumption contributes materially to overall power budget. Rail-to-rail operation should be considered alongside output-current capability, noise, offset, stability, and slew-rate requirements; those detailed electrical limits should be checked in the manufacturer datasheet before selecting external feedback components or driving heavy loads. Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filters, threshold detection, and low-frequency signal conditioning. The single SOT-23-5 package also supports portable instruments, battery monitoring systems, industrial transducers, and embedded analog front ends where board area and power consumption are both important design constraints. For implementation, use the manufacturer pin description table to preserve the correct input, output, supply, and offset-null assignments. Place the bypass capacitor close to the supply pin and route the sensitive input and feedback paths away from switching nodes. Verify stability, output swing, input common-mode behavior, and noise performance at the actual supply voltage and operating temperature. This product page combines manufacturer-family operating limits with practical application guidance, SOT-23-5 implementation considerations, a parameter-focused comparison, and drop-in screening notes. Those engineering details help narrow the design choice while leaving final suitability decisions to the complete circuit requirements.

طلب عرض سعر اتصل بنا
TS942AID - Dual Rail-to-Rail Op Amp, 2.5-10V | STMicroelectronics
TS942AID

TS942AID - Dual Rail-to-Rail Op Amp, 2.5-10V | STMicroelectronics

The STMicroelectronics TS942AID is a dual rail-to-rail operational amplifier designed for general-purpose instrumentation and low-voltage analog signal conditioning. It operates from a 2.5 V to 10 V supply range, is specified over a -40 °C to +85 °C temperature range, and is packaged in an 8-SOIC. The two amplifier channels are intended for applications requiring rail-to-rail output capability, low input bias current, and compact dual-channel implementation. An operational amplifier is an active semiconductor device that uses high open-loop gain to amplify the difference between two input voltages. The TS942 belongs to the STMicroelectronics TS94x family, which is characterized for operation from 2.5 V to 10 V. Rail-to-rail output capability allows the output voltage to approach the supply rails more closely than a conventional fixed-output amplifier, making the device useful in battery-powered, portable, measurement, and signal-conditioning systems. The TS942AID combines two amplifiers in one 8-SOIC package. The verified product information identifies the part as a standard general-purpose dual amplifier with rail-to-rail operation. Its low-power characteristics and 5 mA per channel output-current capability make it suitable for low-voltage analog systems where component count, supply efficiency, and board area are important. The device can be used for sensor interfaces, instrumentation amplifiers, filtering, comparators, and general voltage amplification. The TS942AID is supplied in an 8-SOIC package, providing a standard surface-mount footprint for leaded analog designs. The dual-channel configuration allows independent signal paths to share one package while preserving the familiar operational-amplifier pin arrangement. Because the device is specified down to 2.5 V, it is appropriate for systems using a 3 V or 3.3 V rail, although the exact input and output common-mode limits should be checked in the manufacturer datasheet for the operating condition. For low-voltage designs, pay attention to output swing, input common-mode range, noise, offset voltage, and stability with the selected load. Place bypass capacitors close to the supply pins and route sensitive input signals away from high-current switching paths. The 8-SOIC footprint also makes the TS942AID convenient for designs that need a straightforward replacement footprint rather than a fine-pitch or exposed-pad package. This product page combines the TS942AID manufacturer family information, exact distributor listing details, package identification, application guidance, and a practical comparison with verified drop-in alternatives. It is intended to help engineers evaluate the TS942AID for 2.5 V to 10 V dual rail-to-rail analog designs and identify compatible replacement options.

طلب عرض سعر اتصل بنا
TS942AIN - Dual Rail-to-Rail Micropower Op Amp | STMicroelectronics
TS942AIN

TS942AIN - Dual Rail-to-Rail Micropower Op Amp | STMicroelectronics

STMicroelectronics TS942AIN is a dual general-purpose operational amplifier designed for low-voltage, low-power signal-conditioning systems. The device provides rail-to-rail output operation, a 2.5 V to 10 V supply range, and a micropower supply current of approximately 1.2 uA per channel. It is packaged in an 8-pin Mini DIP configuration for through-hole assembly. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while offering high input impedance, low output impedance, and stable operation around the supply rails. The TS942AIN belongs to the broader hierarchy of operational amplifier, analog amplifier, signal-conditioning IC, and power-management-dependent semiconductor. Its rail-to-rail output stage is useful when the required output signal must approach the positive or negative supply limit. The principal features of the TS942AIN include low quiescent current, dual-channel configuration, rail-to-rail output capability, and operation from 2.5 V to 10 V. The low 1.2 uA per-channel supply current reduces the burden on battery-powered or energy-harvesting systems. A typical output current of 5 mA is suitable for normal low-frequency analog signal paths, subject to the load, voltage, and stability limits defined by the manufacturer. The TS94x family is characterized for operation from 2.5 V to 10 V over a -40 °C to +85 °C temperature range. TS942AIN is the dual-amplifier version with a Mini DIP package. The 8-pin through-hole package supports conventional PCB assembly and is convenient when a compact surface-mount package is not required. Rail-to-rail output behavior improves signal swing in low-voltage instrumentation, sensor interfaces, and portable measurement circuits. Typical applications include portable sensor conditioning, low-power monitoring, current-loop interfaces, and low-voltage analog signal processing. In a sensor circuit, the TS942AIN can amplify a small transducer voltage while operating from a compact supply. In a portable measurement system, its micropower operation helps limit standby consumption. When driving larger capacitive loads or operating at higher frequencies, the designer should verify the applicable stability and load-current limits in the manufacturer datasheet. For PCB design, place the device close to the signal source and preserve short analog input traces to reduce susceptibility to noise and parasitic loading. Decouple the power supply with a local bypass capacitor and route return currents away from sensitive signal paths. The manufacturer product page and the TS942AIN datasheet should be used to confirm the exact pin assignment, electrical limits, input common-mode range, output swing, and recommended operating conditions. This page combines the manufacturer family information with practical selection guidance, package details, sourcing information, and engineering considerations. It is intended to help engineers determine whether the TS942AIN’s dual low-power architecture and 8-pin Mini DIP format fit a specific analog design before finalizing the schematic and PCB layout.

طلب عرض سعر اتصل بنا
TS942BID - Dual Rail-to-Rail Micropower Op Amp | STMicroelectronics
TS942BID

TS942BID - Dual Rail-to-Rail Micropower Op Amp | STMicroelectronics

The STMicroelectronics TS942BID is a dual-circuit, rail-to-rail output micropower operational amplifier packaged in an 8-pin SOIC. Its 2.5 V to 10 V supply range, 60 dB gain-bandwidth product, 5 mA output current capability, and approximately 1.2 µA supply current per channel suit low-voltage analog systems that require low quiescent power and input/output operation near the supply rails. The TS942BID is intended for instrumentation, signal-conditioning, and general-purpose analog applications. An operational amplifier is a high-gain analog building block that compares two input voltages and amplifies their difference. Within the broader semiconductor hierarchy, the TS942BID belongs to the operational-amplifier category, then analog amplifier ICs, and finally integrated circuits. Rail-to-rail output capability permits the output to approach the positive and negative supply limits under suitable load and output-voltage conditions, making the device useful in low-voltage sensor, portable-instrumentation, and battery-powered signal chains. The device uses a 2.5 V minimum operating supply and supports supplies up to 10 V. Its typical gain-bandwidth product is 60 dB, while its typical output current capability is 5 mA per channel. The low-power operating characteristics are reflected in a quoted supply current of 1.2 µA per channel, and the offset-related listing identifies approximately 0.00015 µA, or 150 nA, of input bias current. These characteristics make the TS942BID appropriate for applications in which amplifier power can dominate the total system budget. The TS942BID contains two amplifier channels in one compact 8-SO package. Its standard general-purpose classification and rail-to-rail architecture make it suitable for signal conditioning, low-level amplification, and buffer stages. Designers should still account for the finite gain-bandwidth product when operating at higher closed-loop gains, because bandwidth reduces as the noise gain rises. Input common-mode range, output swing, offset voltage, noise density, and slew rate should be confirmed from the manufacturer datasheet before precision or high-speed signal-chain use. Typical application areas include portable sensor interfaces, low-power instrumentation, battery-operated measurement systems, and general analog signal conditioning. In a sensor interface, the TS942BID can amplify a low-level sensor output while keeping channel current consumption small. In an instrumentation block, its dual-channel configuration can reduce component count when two related signals must be conditioned. As a buffer, it can isolate a higher-impedance source from a downstream analog stage while maintaining a compact eight-pin footprint. Layout and stability remain important in micropower designs. Place input and feedback components close to their associated pins, keep sensitive input traces away from switching nodes, and avoid long high-impedance traces that can increase leakage and noise pickup. Select passive feedback values that account for the amplifier’s gain-bandwidth limit, and verify operation across the full 2.5 V to 10 V supply range. The manufacturer datasheet should be used for the final pin assignment, typical characteristics, absolute maximum ratings, and application-circuit details. This product summary combines the manufacturer’s device description with practical guidance for package reuse, analog layout, low-power selection, and replacement evaluation. It also distinguishes verified drop-in interchangeability from merely similar amplifier functions, helping engineers avoid PCB rework and unexpected bias, bandwidth, or supply-voltage differences.

طلب عرض سعر اتصل بنا
TS942BIN - Dual Micropower Rail-to-Rail Op Amp | ST
TS942BIN

TS942BIN - Dual Micropower Rail-to-Rail Op Amp | ST

The STMicroelectronics TS942BIN is a dual, general-purpose operational amplifier with rail-to-rail output, a 10 kHz gain-bandwidth product, and a typical supply current of 1.2 µA per amplifier. The device operates from 2.5 V to 10 V across a -40 °C to +85 °C temperature range and is supplied in an 8-pin PDIP package. An operational amplifier is an analog signal-conditioning IC that uses high-gain differential amplification to compare two input voltages. The TS94x series belongs to the low-power operational-amplifier hierarchy, combining rail-to-rail output capability with low bias current. This makes it useful in battery-powered instrumentation, sensor interfaces, buffer stages, and other systems that require low supply current without bipolar-input transistor limitations. Key characteristics include two amplifier circuits, rail-to-rail output operation, a 10 kHz gain-bandwidth product, a slew rate of 0.0045 V/µs, input offset voltage of up to 2 mV, and input bias current as low as 1 pA. The low 1.2 µA supply current is particularly valuable in portable equipment, while the 2.5 V minimum supply voltage supports low-energy system rails. The micropower architecture favors low-frequency signal conditioning rather than high-speed amplification. Its 10 kHz gain-bandwidth product limits usable closed-loop bandwidth according to the selected feedback network, while the 0.0045 V/µs slew rate governs large-signal response. Rail-to-rail output improves output swing on low-voltage supplies, although input common-mode range, output loading, and stability still require careful circuit-level evaluation. Typical uses include buffering sensor outputs, amplifying low-level signals in battery-operated instruments, driving analog measurement inputs, and providing gain stages in portable monitoring equipment. The dual configuration can implement two independent amplifiers in instrumentation, filtering, or signal-conditioning circuits while reducing package count. Layout should keep input, feedback, and decoupling connections short, and should avoid routing high-impedance input traces beside switching or high-current paths. Place the supply bypass capacitor close to the device, observe common-mode and output-swing limits, and verify stability with the intended source and load impedances. Because the TS942BIN is obsolete, maintain a controlled last-time-buy plan for maintenance and repair production.

طلب عرض سعر اتصل بنا
TS942ID - Dual Micropower Op Amp | STMicroelectronics
TS942ID

TS942ID - Dual Micropower Op Amp | STMicroelectronics

The STMicroelectronics TS942ID is a dual, rail-to-rail, micropower operational amplifier with two amplifier channels, a 10 kHz gain-bandwidth product, and a 0.0045 V/us slew rate. It operates from a single supply of 2.5 V to 10 V and is packaged in an 8-pin SOIC. Each channel is designed for low-power signal conditioning and general-purpose analog measurements. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify, buffer, filter, or compare small voltage signals. In the signal-chain hierarchy, the TS942ID belongs to the operational-amplifier family within analog amplifier ICs and power-management systems. Its micropower operating current and rail-to-rail output behavior make it suitable for portable instrumentation, sensor interfaces, and low-voltage analog equipment. The TS942ID provides a supply-current consumption of 1.2 uA and an ultra-low input bias current of 1 pA. These characteristics reduce loading on high-impedance sensors and conserve energy in battery-operated systems. Its output swing is rail-to-rail, while single-supply operation extends to 10 V. The device also includes CMOS inputs, 2 kV ESD protection, and latch-up immunity for improved handling robustness. With a gain-bandwidth product of 10 kHz and a slew rate of 0.0045 V/us, the TS942ID favors precision and low-power operation over wideband performance. The 10 kHz bandwidth is suitable for slow sensor signals, ECG-scale physiological waveforms, precision current measurement, and low-frequency filtering. CMOS input stages support very low bias current, making the amplifier appropriate for high-source-impedance transducers where input loading must remain minimal. Typical uses include portable biomedical instrumentation, low-power sensor conditioning, battery-powered data acquisition, industrial process monitoring, and general-purpose buffering. Two independent channels can process complementary signals or provide simultaneous amplification. Because each channel can also be configured as a comparator-style element with suitable feedback, designers can use the same device for basic threshold and level-detection functions. The principal design consideration is bandwidth. The 10 kHz gain-bandwidth product limits high-gain signal bandwidth, so applications requiring faster edges or wider closed-loop bandwidth should account for the amplifier's finite slew rate. Input and output stability must also be evaluated with the source impedance, load capacitance, supply voltage, and selected feedback network.

طلب عرض سعر اتصل بنا
TS942IN - Dual 1.2 µA Rail-to-Rail Op Amp | STMicroelectronics
TS942IN

TS942IN - Dual 1.2 µA Rail-to-Rail Op Amp | STMicroelectronics

STMicroelectronics TS942IN is a dual, rail-to-rail output micropower operational amplifier designed for 2.5 V to 10 V single-supply operation. The device provides two amplifier circuits in an 8-pin Mini DIP package, with a typical micropower consumption of 1.2 µA. Its CMOS inputs feature ultra-low input bias current, while the rail-to-rail output stage supports low-voltage signal conditioning where the output must approach the supply rails. The specified operating temperature range is -40 °C to +85 °C. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TS94x family belongs to the operational amplifier, analog amplifier, and linear integrated-circuit hierarchy. Operational amplifiers are widely used as voltage followers, buffers, comparators, transimpedance amplifiers, and active analog filters. The TS942IN combines low supply current, single-rail operation, CMOS input characteristics, and rail-to-rail output swing in one low-power analog building block. The 1.2 µA micropower characteristic makes the TS942IN particularly suitable for battery-operated sensors, portable instruments, and low-energy monitoring systems. Its 2.5 V minimum supply voltage allows operation from a single low-voltage cell or regulated rail. Rail-to-rail output swing is valuable in low-voltage systems because it increases usable output range. The low input bias current reduces errors in source impedance-sensitive circuits and minimizes disturbance to high-impedance sensors. The TS942IN uses CMOS input circuitry and is intended for general-purpose low-power analog signal processing. Each amplifier can support common inverting, non-inverting, and voltage-following configurations. Because the output approaches the supply rails, careful load and feedback design remains necessary when the output must achieve accurate levels near either rail. Input common-mode range, output swing, gain-bandwidth behavior, and stability conditions should be taken directly from the manufacturer datasheet when selecting feedback networks. Typical uses include low-frequency sensor conditioning, portable instrumentation, medical monitoring, industrial threshold detection, and energy-efficient data acquisition. In battery-powered equipment, the low supply current reduces the continuous load imposed by the amplifier. In precision measurements, the low input bias current helps preserve the signal from sensors with high source impedance. The device is also useful when one package must provide two matched functional amplifier channels. Designers should verify the permitted input and output ranges at the selected supply voltage, account for input and output capacitance in feedback layouts, and avoid driving a load that exceeds the amplifier's recommended capability. A stable bypass capacitor close to the supply pins and short, direct routing for high-impedance inputs help preserve low-noise and low-power performance. This product page combines the manufacturer specifications, package information, sourcing guidance, functional alternatives, and practical circuit-level considerations for engineers evaluating the TS942IN. It is intended to accelerate part selection while keeping the critical design tradeoffs explicit: low power and low bias current versus the bandwidth, noise, and load capability required by a particular signal chain.

طلب عرض سعر اتصل بنا
TS942IPT - 10kHz Dual RRO Op Amp | STMicroelectronics
TS942IPT

TS942IPT - 10kHz Dual RRO Op Amp | STMicroelectronics

The STMicroelectronics TS942IPT is a dual-circuit, rail-to-rail operational amplifier with a 10 kHz gain-bandwidth product, supplied in an 8-pin TSSOP package. The device combines rail-to-rail input and output capability with low supply current and is intended for compact, low-power analog signal-processing systems. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using negative feedback to establish gain and bandwidth. A rail-to-rail input stage accepts signals close to the positive and negative supply rails, while a rail-to-rail output stage can approach those limits under suitable load conditions. The TS942IPT therefore belongs to the rail-to-rail operational-amplifier family within the broader amplifier and analog IC hierarchy. Key characteristics include two amplifier circuits in one package, 10 kHz gain-bandwidth product, rail-to-rail operation, and approximately 1.2 µA supply current per channel. Its listed typical output current is 5 mA. These characteristics make it suitable for low-power sensor interfaces, portable instrumentation, and signal-conditioning circuits where device count, board area, and energy use are important constraints. The TS942IPT uses an 8-TSSOP package measuring approximately 0.173 inch, or 4.40 mm, in width. Tape-and-reel packaging supports high-volume automated assembly. The manufacturer specifies an operating-temperature range of -40 °C to +85 °C. As a general-purpose dual amplifier, it can reduce component count in designs that need two nearly identical signal-conditioning channels. Typical uses include low-level sensor signal conditioning, battery-powered measurement modules, industrial control interfaces, portable medical instruments, and low-voltage audio or communication front ends. Two independent amplifier sections can handle separate channels in a dual-axis sensor, differential receiver, filter, or gain stage, provided each channel's stability, common-mode range, and output-drive requirements are satisfied. Designers should verify input and output headroom, capacitive-load behavior, noise performance, and output-current demand against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage. The low 10 kHz bandwidth favors precision and low-power operation rather than high-speed signal handling. This page combines the exact TS942IPT package and operating characteristics with application guidance, same-family drop-in alternatives, a parameter comparison, and practical layout considerations. It helps engineers evaluate the amplifier's role in low-power analog designs without confusing it with higher-bandwidth or higher-current rail-to-rail amplifiers.

طلب عرض سعر اتصل بنا
TS944AID - Quad Rail-to-Rail Micropower Op Amp | STMicroelectronics
TS944AID

TS944AID - Quad Rail-to-Rail Micropower Op Amp | STMicroelectronics

STMicroelectronics TS944AID is a four-circuit, rail-to-rail output operational amplifier designed for low-voltage and low-power signal-conditioning systems. The device operates from 2.5 V to 10 V, supports an operating temperature range of -40°C to +85°C, and is packaged in a 14-pin SOIC. Each amplifier consumes approximately 1.2 µA of supply current, making the TS944AID suitable for battery-powered instrumentation, portable measurement systems, and industrial sensor interfaces. An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, and compare small voltage signals. The TS944AID belongs to the rail-to-rail output operational-amplifier family, combining four independent amplifier channels with a common supply in one compact 14-pin package. Rail-to-rail output operation allows the output voltage to approach the supply rails more closely than a conventional fixed-headroom amplifier, improving usable signal range in low-voltage systems. The four-channel arrangement reduces package count and simplifies routing in designs requiring several similar amplifier stages. A 2.5 V minimum supply supports low-energy systems, while the 10 V maximum supply provides flexibility for conventional industrial signal ranges. The approximately 1.2 µA supply current per channel is particularly valuable when every microwatt affects battery life. The -40°C to +85°C operating range supports industrial equipment and consumer products requiring operation beyond room temperature. STMicroelectronics describes the TS944 series as micropower, rail-to-rail output operational amplifiers. Its four-channel architecture is useful for sensor conditioning, current-loop receivers, filtering, and low-level signal buffering. Because the TS944AID combines four amplifiers in one package, matching channels can simplify calibration, reduce board area, and keep sensitive analog paths physically close. Decoupling and stable-reference techniques remain important when the amplifier operates beside switching circuitry or long sensor cables. Typical uses include industrial pressure and temperature sensors, low-power condition-monitoring equipment, portable measurement instruments, analog interface boards, and general-purpose signal buffers. In a sensor front end, two channels can amplify or level-shift sensor outputs while the remaining channels support filtering, threshold detection, or output buffering. Its low supply current is advantageous when the complete system must operate from a small energy source rather than a laboratory supply. For PCB design, place the supply bypass capacitor close to the device and route high-impedance input and feedback traces away from switching nodes and fast digital signals. Confirm output swing, input common-mode range, stability, and capacitive-load limits against the manufacturer datasheet for the actual supply voltage and load. Verify the exact pin orientation and channel assignments before assembly because the SOIC-14 outline alone does not identify the functional pins. This product page consolidates the device identity, operating envelope, package information, replacement considerations, and application-oriented design guidance. It also distinguishes confirmed family information from parameters that require direct consultation of the manufacturer datasheet before precision analog design or PCB release.

طلب عرض سعر اتصل بنا