الدوائر المتكاملة

DSPIC33EP512MC806-E/PT

DSPIC33EP512MC806-E/PT - 512KB Flash 16-bit DSC, 64-TQFP | Microchip

The Microchip Technology DSPIC33EP512MC806-E/PT is a high-performance 16-bit Digital Signal Controller (DSC) from the dsPIC33EP family, integrating a 70 MIPS dsPIC DSC core with 512 KB of Flash program memory and 53 KB of RAM in a 64-pin TQFP (10x10 mm) package. It is purpose-built for advanced motor control, digital power conversion, and real-time DSP applications, offering a 60 MIPS (max) execution throughput when operating from a 3.0 V to 3.6 V supply. A Digital Signal Controller (DSC) is a hybrid MCU/DSP architecture that combines a microcontroller's deterministic interrupt handling and peripherals with a digital signal processor's single-cycle MAC engine and barrel shifter. DSP engines fall under the broader hierarchy of microcontrollers -> embedded processors -> microcomputing units, sitting in the same tier as the Cortex-M4 and dsPIC33E/C families, but optimized for closed-loop control rather than general compute. The dsPIC33EP series specifically targets motor control and power-conversion workloads where PWM edge accuracy and ADC sampling determinism matter more than raw CPU frequency. Key features of the DSPIC33EP512MC806-E/PT include dual motor-control PWM modules with up to 7 PWM outputs each, two 10-bit A/D converters (up to 32 input channels total), two analog comparators, two quadrature encoder interfaces, and dual CAN 2.0B controllers. The integrated DSP engine provides single-cycle 16x16-bit MAC with saturation, allowing real-time computation of Clarke/Park transforms and PI controllers without software emulation. AEC-Q100 qualification makes the E (extended) temperature grade device suitable for automotive environments from -40°C to +125°C. Typical applications include sensorless and field-oriented control (FOC) of three-phase PMSM and BLDC motors, digitally controlled switched-mode power supplies (SMPS), solar inverters, servo drives, and industrial PLCs. Two CAN interfaces simplify integration into vehicle body/comfort networks, while the dual QEI channels enable simultaneous position feedback from two motors. Power-conscious designs benefit from the integrated DSP instructions that replace software filter-loop computations. When designing with this device, plan memory allocation between the 512 KB Flash (170K x 24) and 53 KB RAM early, and verify PWM-to-ADC synchronization timing on the chosen TQFP-64 routing. Boot Flash and dual-partition Flash modes can simplify in-field firmware upgrades - refer to the device family reference manual for ICSP/ICD layout. This page synthesizes distributor pricing, pin-compatible variants, and design notes beyond what the manufacturer datasheet alone provides.

طلب عرض سعر اتصل بنا

DSPIC33EP512MC806-I/MR

DSPIC33EP512MC806-I/MR - 70 MIPS 16-bit DSC, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MC806-I/MR is a 16-bit digital signal controller (DSC) delivering 70 MIPS performance from its dsPIC33E core, with 512KB (170K x 24) of flash program memory and 53,248 bytes of RAM, housed in a 64-pin VQFN (9x9 mm) package, industrial temperature grade -40C to +85C. A digital signal controller combines the computational architecture of a microcontroller with the math acceleration of a digital signal processor. Within the power-management hierarchy of embedded control, the DSC sits above general-purpose MCUs and alongside dedicated DSPs, providing single-cycle MAC (multiply-accumulate) instructions, hardware divide support, and DSP engine features while retaining MCU-style peripherals, interrupts, and flash-based code storage. This makes the dsPIC33E family a de facto standard for embedded motor control and digital power conversion. Key features of the DSPIC33EP512MC806-I/MR include the 70 MIPS dsPIC DSC core with integrated DSP engine, dual CAN modules (the datasheet describes this device as a DSC with Dual Motor Control, Dual CAN), a high-speed PWM module tailored for motor control, and Peripheral Pin Select (PPS) that allows remapping of RPn/RPIn pins to many digital peripherals for maximum layout flexibility. Architecturally, the dsPIC33E core executes an enhanced 16-bit instruction set with DSP-class addressing modes, supporting precision control loops for field-oriented motor control, digital power supplies (PFC, LLC), and digital audio processing. The large 512KB flash accommodates complex control firmware, bootloaders, and parameter tables, while the 53 KB RAM supports buffering for communication stacks and control-loop state. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, solar inverters and digital power supplies, automotive and industrial CAN networking nodes, and high-performance embedded control systems requiring deterministic DSP math. Design consideration: this device is reported to be more sensitive to cross-talk between the PGEC and PGED in-circuit programming lines than other PIC devices, so keep ICSP traces short and well-guarded to avoid programming failures. This page synthesizes verified distributor pricing, drop-in alternatives within the same 64-VQFN footprint, and practical design notes not found on a single manufacturer or distributor page.

طلب عرض سعر اتصل بنا

DSPIC33EP512MC806-I/PT

DSPIC33EP512MC806-I/PT - 70 MIPS 16-bit DSC, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MC806-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP MC family, integrating a 70 MIPS DSP-enhanced core with 512 KB of Flash program memory and 52 KB of RAM in a 64-pin TQFP (10x10 mm) package rated -40C to +85C and operating at 3.3 V. A digital signal controller (DSC) bridges the gap between a microcontroller and a digital signal processor by combining deterministic interrupt response, integrated peripherals, and a single-cycle 16x16 hardware multiply-accumulate (MAC) with barrel shifter. In the broader power-management and real-time-control hierarchy, the dsPIC33E family sits between general-purpose 16-bit MCUs and dedicated DSPs, with embedded control positioned as digital-signal controller -> 16-bit MCU -> microcontroller -> semiconductor. Hypernyms and synonyms: DSC = digital signal controller = dsPIC = DSC. Key features include the 70 MIPS dsPIC33E core with single-cycle MAC, dual high-speed motor-control PWM modules with complementary outputs and dead-time insertion, two CAN 2.0B modules, and a rich serial mix of I2C, I2S, SPI, and UART/USART interfaces. The device exposes 53 general-purpose I/O pins and carries the -I industrial temperature grade. Architecturally, the dsPIC33EP core uses an enhanced Harvard bus with 24-bit instruction words, allowing program memory up to 512 KB to be fetched every cycle. The high-speed PWM modules support center-aligned and edge-aligned modes with sub-microsecond resolution, essential for three-phase inverter and digital power topologies. Internal voltage regulators, an on-chip oscillator with PLL, and DMA channels reduce external component count. Typical applications include precision motor control (BLDC, PMSM, ACIM), digital power conversion and solar inverters, industrial automation nodes using dual CAN buses, and embedded control requiring DSP-class math for sensor filtering. The dual CAN modules make the part especially suitable for industrial networked systems. Design consideration: all VDD and VSS pins must be connected for reliable operation, and the ICSP PGECx/PGEDx pins must be used as a matched pair. The 64-pin TQFP package requires attention to the VCAP pin for the internal core regulator stabilization capacitor. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet, giving engineers a single citable reference for the DSPIC33EP512MC806-I/PT.

طلب عرض سعر اتصل بنا

DSPIC33EP512MC806T-I/PT

DSPIC33EP512MC806T-I/PT - 70 MIPS DSC 512KB Flash TQFP-64 | Microchip

The Microchip Technology DSPIC33EP512MC806T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 70 MIPS performance with 512 KB (170K x 24) of Flash program memory and 52 KB (53,248 bytes) of data RAM, housed in a 64-pin TQFP (10x10 mm) package operating from 3V to 3.6V. A digital signal controller combines the computational architecture of a digital signal processor (DSP) with the peripheral set and ease of use of a microcontroller (MCU). Within the power management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes multiply-accumulate (MAC) and DSP instructions for signal processing while simultaneously managing real-time control loops. The dsPIC33E family is Microchip's high-performance 16-bit DSC platform targeted primarily at digital power and precision motor control. Key features of this part include the 70 MIPS dsPIC33EP core, dual CAN modules (the dual-CAN 806 variant), dedicated motor-control PWM peripherals, a 10-bit high-speed ADC, and 1 ns-resolution timers. The I-grade temperature rating of -40C to +85C supports industrial environments. The 'T' suffix indicates tape-and-reel delivery for automated assembly, and the '/PT' suffix denotes the lead-free 64-pin TQFP package. Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with 24-bit instructions and a wide 16-bit data path, enabling single-cycle MAC operations and hardware division support that offloads control-loop computation. Microchip designed this family specifically for high-performance, energy-efficient precision motor control systems, incorporating enhanced on-chip peripherals that reduce external component count. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, digital power supplies and inverters, industrial automation and robotics controllers, and CAN-networked automotive and industrial nodes. When designing with this controller, budget the 3.3V supply rail carefully: the absolute maximum operating range is 3V to 3.6V, and all 64 I/O pins should be decoupled with 100 nF ceramics placed at each VDD pin pair for clean ADC and PWM operation. This page synthesizes distributor pricing and stock data from DigiKey, Mouser, LCSC, and Octopart, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810-E/BG

DSPIC33EP512MU810-E/BG - 16-bit 70 MIPS DSC, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MU810-E/BG is a 16-bit digital signal controller (DSC) with a 70 MIPS dsPIC33E core, 512 KB (170K x 24) Flash memory, 52 KB SRAM, integrated USB and dual CAN modules, housed in a 121-ball TFBGA (10x10 mm) package with extended temperature range of -40C to +125C. A digital signal controller combines the computation throughput of a DSP with the deterministic, interrupt-driven behavior and peripheral set of a microcontroller. In the semiconductor hierarchy it sits above general-purpose MCUs and beside DSPs, belonging to the broader class of 16-bit embedded processors used in closed-loop control systems where fast multiply-accumulate operations are required. Key features include the 70 MIPS dsPIC33E DSP engine with dual 40-bit accumulators and single-cycle MAC, high-speed PWM modules purpose-built for motor control, full-speed USB OTG, two CAN 2.0B controllers for industrial networking, and Microchip nanoWatt XLP low-power technology for reduced standby consumption. Technically, the dsPIC33EP512MU810 executes from 3.0V to 3.6V single-supply operation, supports 60 MHz internal clocking per distributor listings, and integrates 51 I/O pins in the BGA option along with advanced analog peripherals. The E suffix denotes the extended -40C to +125C operating range, and the device is listed as AEC-Q100 capable for automotive environments by distributor sources. Typical applications include dual motor control (BLDC, PMSM, ACIM), digital power supplies and solar inverters, and automotive or industrial gateways that need USB plus dual CAN connectivity. Design consideration: plan the 121-ball BGA layout early - escape routing requires controlled-impedance fanout and a solid ground plane; power supply decoupling on all VDD balls is essential for the 70 MIPS core. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810-E/PF

DSPIC33EP512MU810-E/PF - 16-bit DSC, 70 MIPS, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MU810-E/PF is a 16-bit Digital Signal Controller (DSC) from the dsPIC33EP family, operating at up to 70 MIPS (60 MHz external clock / internal PLL) with 512 KB (170K x 24) of Flash program memory, 52 KB of SRAM, dual CAN 2.0B modules, a full-speed USB OTG interface, and a 100-pin TQFP (14x14 mm) package with extended -40C to +125C temperature range. A Digital Signal Controller combines the computational architecture of a digital signal processor (DSP) with the peripheral set and control-oriented design of a microcontroller (MCU). Within the power-management hierarchy, the dsPIC33EP family sits above basic PIC16/PIC24 MCUs in the Microchip portfolio, integrating a DSP engine with multiply-accumulate (MAC) instructions, high-speed PWM modules, and advanced analog peripherals - making it a hybrid between a general-purpose MCU and a dedicated DSP such as TI's TMS320F28xx series. Key differentiating features include the high-speed 70 MIPS core, 15-channel DMA controller for moving data between peripherals and RAM without CPU intervention, dual CAN bus interfaces (targeting industrial and automotive networking), USB OTG connectivity, and multiple motor-control-oriented PWM modules supporting complementary outputs with dead-time insertion. The device is built on CMOS technology and includes nine timers and five external interrupt sources. Architecturally, the dsPIC33EP core pairs a 16-bit modified Harvard pipeline with an integrated DSP engine, providing single-cycle MAC and dual data fetch. Flash is split into program pages and can be self-written at runtime; the 52 KB SRAM includes an X-Y addressing mode that benefits digital filtering and FFT algorithms common in motor control and power conversion. Typical applications include dual-motor control in industrial drives, digital power supplies and PFC stages, UPS systems, automotive body electronics, and instrumentation requiring CAN or USB connectivity alongside real-time DSP performance. For design, supply voltage must be regulated within the 3.0 V to 3.6 V range, and the E-grade suffix confirms suitability across the full -40C to +125C industrial/automotive ambient range. This page synthesizes distributor pricing, drop-in alternatives from the same dsPIC33EP family, and practical design notes beyond what the manufacturer datasheet alone provides.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810-E/PT

DSPIC33EP512MU810-E/PT - 16-bit DSC 60 MIPS USB TQFP-100 | Microchip

The Microchip Technology DSPIC33EP512MU810-E/PT is a 16-bit digital signal controller (DSC) delivering up to 60 MIPS from its dsPIC33E core, with 512 KB (170K x 24) of Flash program memory, 52 KB of SRAM, and integrated full-speed USB 2.0 On-The-Go, housed in a 100-pin TQFP (12x12 mm) package with extended -40C to +125C temperature rating. A digital signal controller combines the compute characteristics of a digital signal processor with the peripheral integration and control-oriented architecture of a microcontroller. Within the power-management hierarchy of embedded systems, the DSC sits between a general-purpose MCU and a dedicated DSP, making the dsPIC33E family a common choice for precision motor control, digital power conversion, and sensing applications that require both fast multiply-accumulate arithmetic and rich on-chip peripherals. Key features include a 17-bit x 17-bit hardware multiplier with a 40-bit accumulator, 15 DMA channels for low-CPU-overhead data movement, high-speed PWM modules optimized for three-phase motor and digital-power topologies, four UART/SPI/I2C serial interfaces, and a 12-bit ADC with up to 1.1 Msps conversion rate on the analog peripherals. The 512 KB Flash supports self-programming for in-field firmware updates. The dsPIC33EP MU810 family uses Microchip's 16-bit EP core architecture with linear program memory addressing up to 4M instruction words, hardware integer division support, and a deterministic interrupt controller. USB OTG, CAN, and SENT peripherals enable networked industrial nodes without an external bridge IC. Typical applications include brushless DC and PMSM motor drives running sensorless field-oriented control, digital power supplies and solar micro-inverters, USB-connected industrial instrumentation, and general-purpose sensing nodes running FFT or FIR DSP filters. The integrated USB also suits data-acquisition probes and Human Interface Devices (HID). When designing with this part, ensure a 3.0V to 3.6V supply with proper decoupling on every VDD/VSS pair and a clean AVDD rail for the on-chip ADC; plan the TQFP-100 ground strategy from the first PCB revision to avoid analog digital noise coupling into the PWM feedback paths. This page synthesizes distributor pricing, same-family drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810-I/BG

DSPIC33EP512MU810-I/BG - 16-bit 70 MIPS DSC, 512KB Flash | Microchip

The Microchip DSPIC33EP512MU810-I/BG is a 16-bit digital signal controller (DSC) delivering 70 MIPS from its dsPIC33EP core, with 512 KB (170K x 24) of flash program memory, 52 KB of RAM, and integrated USB, dual CAN, and high-speed PWM peripherals, housed in a 121-ball TFBGA (10x10 mm) package. A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and ease of use of a microcontroller (MCU). Within the embedded hierarchy, the dsPIC33EP family sits between general-purpose 16-bit MCUs and dedicated DSPs, executing digital filter algorithms, fast control loops, and audio/speech processing with a modified Harvard architecture and a C-compiler-optimized instruction set. Key features include a 16-bit data path with 24-bit-wide instructions, linear program memory addressing up to 4 M instruction words, dual CAN 2.0B modules, full-speed USB, 15-channel DMA, and motor-control PWM peripherals. Mouser lists the device as a 100P, 512 KB flash, 52 KB RAM, 60 MHz part with USB, and the 'MU' suffix identifies USB and dual motor-control capability per Microchip's product page. Architecturally, the dsPIC33EP core supports single-cycle MAC, hardware divide, and DSP addressing modes, letting a single chip close high-speed current loops for FOC motor control while simultaneously servicing USB or dual CAN communication. The extensive DMA controller offloads data movement between peripherals and RAM, preserving CPU cycles for control math. Typical applications include precision motor control (the PIM infosheet notes compatibility with Microchip MCLV DM330021, MCHV DM330023, and MCSM DM330022 development boards), industrial automation and CAN networking nodes, and digital power supplies / USB-connected instrumentation. Design consideration: BGA packages require controlled-impedance PCB fabrication with fine-pitch via-in-pad or dog-bone fanout; if your process cannot support 121-ball TFBGA assembly, the same die is available in a 100-pin TQFP (DSPIC33EP512MU810-I/PT), which is functionally equivalent but not footprint-compatible. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810-I/PF

DSPIC33EP512MU810-I/PF - 16-bit DSC 70 MIPS USB 2xCAN | Microchip

The Microchip Technology DSPIC33EP512MU810-I/PF is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering up to 70 MIPS with 512 KB of flash program memory (536 KB on-chip memory per distributor data), 52 KB of SRAM, and full-speed USB 2.0 OTG, housed in a 100-pin TQFP (14 x 14 mm) package rated from -40C to +85C. A digital signal controller (DSC) is a hybrid device that fuses the deterministic control architecture of a microcontroller with DSP-grade math acceleration on a single die. Within the power-management and real-time-control hierarchy of embedded systems, the dsPIC33E family sits between general-purpose 32-bit MCUs and dedicated DSPs, offering single-cycle MAC instructions, hardware DSP engine, and enhanced on-chip peripherals. This combination makes the DSC the preferred choice for high-frequency control loops in motor drives, digital switching power supplies, and power-conversion applications where deterministic latency matters more than raw clock speed. Key features include a 16-bit dsPIC DSC core with hardware DSP engine rated at 70 MIPS (60 MHz FCY), 512 KB of user flash with 52 KB SRAM, a 15-channel DMA, dual ECAN modules, full-speed USB 2.0 OTG, and a high-speed PWM engine with complementary outputs and fault inputs suitable for advanced motor control. Up to 83 general-purpose I/O pins plus I2C, SPI, UART, and a Data Converter Interface (DCI) provide rich connectivity. The integrated 10/12-bit ADC supports up to 32 analog channels, enabling three-phase current sensing without external converters. Architecturally, the dsPIC33E family integrates a pipelined RISC core with hardware DSP support and dual motor-control PWM peripherals suitable for twin three-phase drives, per distributor product descriptions. The USB OTG block enables host, device, or on-the-go roles, while dual CAN interfaces support automotive and industrial networks such as CANopen and DeviceNet. The 60 MHz external clock with 4x PLL option drives the 70 MIPS throughput. Typical applications include precision motor control for PMSM, BLDC, and AC induction drives, digital power supplies and solar inverters, industrial automation nodes requiring USB or CAN connectivity, and automotive body/comfort ECUs. Microchip reference designs pair the 100-pin PIM form factor with the MCLV (DM330021), MCHV (DM330023), and MCSM (DM330022) motor control development boards. Design consideration: at 60 MHz FCY operation, ensure adequate decoupling on all VDD and VDDCORE pins and follow Microchip programming specifications for the 3.3V rail. The -I suffix industrial temperature rating of -40C to +85C governs allowable dissipation. Verify your RTDM and CAN baud rate configuration before production lock. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810-I/PT

DSPIC33EP512MU810-I/PT - 16-bit DSC 70 MIPS 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MU810-I/PT is a 16-bit digital signal controller (DSC) delivering up to 70 MIPS from its dsPIC33EP core, integrating 512 KB (170K x 24) of flash memory, 52 KB of SRAM, and a high-speed USB 2.0 full-speed interface, housed in a 100-pin TQFP (12 x 12 mm) surface-mount package with an industrial temperature rating of -40C to +85C. A digital signal controller (DSC) combines the deterministic interrupt latency and peripheral integration of a microcontroller (MCU) with the numeric throughput of a digital signal processor (DSP). Within the embedded compute hierarchy, a DSC sits above basic 8/16-bit MCUs (which typically lack single-cycle hardware multiply-accumulate) and below application processors, providing real-time control loops with DSP-style MAC operations for filters, transforms, and field-oriented control algorithms. The dsPIC33EP family is Microchip's high-performance 16-bit DSC line optimized for precision motor control and digital power conversion. Key features of this device include the 70 MIPS dsPIC DSC core with hardware DSP engine, 512 KB of self-programmable flash supporting in-field firmware updates, 52 KB of on-chip SRAM for control loops and buffering, integrated USB 2.0 full-speed connectivity, dual CAN modules, high-resolution PWM peripherals with duty cycle resolution suited to three-phase inverter switching, and a 10/12-bit ADC with a 1.1 Msps conversion rate. The 100-pin TQFP exposes 83 general-purpose I/O lines for gate drivers, encoder feedback, and communication buses. Technically, the dsPIC33EP architecture uses a modified Harvard bus with a 24-bit instruction word, single-cycle MAC, dual 40-bit accumulators, and dual operand fetch, enabling execution of digital filters, FFTs, and PID compensators without external memory wait states. The MU810 variant emphasizes motor-control peripherals including up to 8 PWM channels with complementary outputs and programmable dead time, suited for sinusoidal and space-vector modulation of PMSM and BLDC motors. Typical applications include precision brushless DC and PMSM motor drives for industrial automation and HVAC, digital power conversion (PFC, LLC, phase-shifted full-bridge), USB-connected embedded control modules for factory sensors and peripherals, and dual-CAN automotive ECUs where high-resolution PWM and 70 MIPS DSP throughput directly improve loop bandwidth and acoustic performance. When designing with this DSC, budget flash allocation carefully: 512 KB accommodates a FOC motor-control stack plus USB and CAN stacks, but bootloader reservation should be planned early. Use Microchip's MCLV-2 (DM330021) or MCHV-3 (DM330023) development boards for firmware bring-up, and verify the 100-pin TQFP thermal and decoupling layout per the manufacturer datasheet. This page synthesizes distributor inventory data, same-family drop-in alternatives, and practical design notes not found in the manufacturer product page alone, helping engineers shorten time-to-prototype when migrating from 8/16-bit MCUs to a 16-bit DSC platform.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810T-I/BG

DSPIC33EP512MU810T-I/BG - 70 MIPS DSC, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MU810T-I/BG is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering up to 70 MIPS core performance, with 512KB (170K x 24) FLASH program memory, 52KB SRAM, and an integrated full-speed USB module, housed in a 121-ball TFBGA (10x10 mm) package. A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, DSCs sit between general-purpose MCUs and dedicated DSPs, executing digital filter algorithms, high-speed precision digital control loops, and digital audio and speech processing that a standard MCU core cannot sustain in real time. Key features include the 70 MIPS dsPIC33E core with DSP engine (17-bit x 17-bit single-cycle MAC, 40-bit accumulators), 32-channel 10/12-bit ADC, high-speed PWM modules suited for motor control, 15 DMA channels, 9 timers, and an operating voltage range of 3.0V to 3.6V with 83 general-purpose I/O pins in the TFBGA-121 footprint. Architecturally, the dsPIC33EP core uses a modified Harvard bus structure with multiple internal buses, supporting single-cycle instruction fetch and dual data fetches that sustain MAC-heavy loops at full clock rate. The -I temperature grade covers -40C to +85C for industrial environments, and the family is offered with AEC-Q100 qualified variants for automotive designs. Typical applications include precision motor control (PMSM, BLDC, stepper), digital power supplies and inverters, USB-connected industrial instruments, and digital audio processing. The 10x10 mm BGA suits space-constrained boards needing high I/O count. Design consideration: TFBGA packages require careful PCB fanout and reflow assembly; if your production line cannot handle BGA assembly, the same die is offered in TQFP-100 (PF) and TQFP-64 (PT) packages. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU810T-I/PT

DSPIC33EP512MU810T-I/PT - 16-bit 70 MIPS DSC, 512KB Flash USB CAN | Microchip

The Microchip Technology DSPIC33EP512MU810T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering 70 MIPS performance, 512KB (170K x 24) Flash program memory, 52KB SRAM, integrated USB and dual CAN modules, housed in a 100-pin TQFP (12x12 mm) package. Operating from a 3V to 3.6V supply at up to 60 MHz external clock, it combines DSP capability with microcontroller peripherals. A digital signal controller is a hybrid class of processor that merges the computational architecture of a digital signal processor (hardware multiply-accumulate, DSP instruction extensions) with the peripheral integration and deterministic control of a microcontroller. In the power-management hierarchy of embedded systems, DSCs sit between general-purpose MCUs and dedicated DSPs, making them the preferred choice for closed-loop, computation-intensive control such as field-oriented motor control and digital power conversion. Key features include the 70 MIPS dsPIC33E core with DSP engine, high-speed PWM peripherals purpose-built for dual motor control, a 32-channel 10/12-bit ADC, USB device support, two CAN 2.0B modules, and 15 DMA channels that offload data movement from the CPU. These peripherals allow one chip to close both current and speed control loops for two motors simultaneously while servicing USB or CAN communication. Architecturally, the dsPIC33E core uses a modified Harvard pipeline with 24-bit instruction words and 16-bit data paths, plus single-cycle MAC and divide support. The Flash retention and self-programming capability support field firmware updates, while the DMA system keeps ADC sample-to-PWM-update latency predictable. Typical applications include dual-axis industrial motor drives (BLDC, PMSM, stepper), digital power supplies and solar inverters, automotive and industrial CAN network nodes, and USB-connected instrumentation. Design consideration: at 70 MIPS the core is sensitive to supply integrity, so a solid 3.3V rail with local decoupling on every VDD/VSS pair and a clean PLL reference clock is essential for stable ADC and PWM operation. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU814-E/PH

DSPIC33EP512MU814-E/PH - 16-bit 70 MIPS DSC, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512MU814-E/PH is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, combining a 70 MIPS dsPIC DSC core with 512KB (536KB formatted) flash memory, 52KB RAM, integrated USB, and a 144-pin TQFP (PH) package, rated from -40C to +125C and AEC-Q100 qualified for automotive use. A digital signal controller is a hybrid class of embedded processor that merges the computational architecture of a microcontroller (flash memory, RAM, peripherals, interrupt system) with the DSP engine of a digital signal processor, including a hardware multiply-accumulate (MAC) unit and barrel shifter. In the system hierarchy, the dsPIC33EP sits between general-purpose MCUs and dedicated DSPs, making it the standard choice for real-time closed-loop control. Key features include the enhanced dsPIC33E CPU core delivering up to 70 MIPS, 9 timers, 15 DMA channels, a high-speed PWM module for motor control and digital power, USB 2.0 connectivity, and extended-temperature operation to +125C - all on a single 3.3V supply. Architecturally, the device uses CMOS technology with a 16-bit RISC pipeline, hardware DSP multiply and barrel-shift resources, and DMA offloading so peripherals such as ADCs and UARTs move data without CPU intervention - critical for deterministic control loops at multi-kilohertz update rates. Typical applications include precision BLDC/ACIM and PMSM motor control, digital power supplies (PFC, LLC converters), industrial automation and sensor fusion nodes, and USB-connected control instrumentation. Design consideration: this device is more sensitive to cross-talk between PGEC/PGED programming lines than other PIC devices; a small capacitor (about 20pF) from PGEC to VSS placed close to the chip improves programming reliability. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU814-E/PL

DSPIC33EP512MU814-E/PL - 16-bit DSC 60MHz 512KB USB | Microchip

The Microchip Technology DSPIC33EP512MU814-E/PL is a 16-bit digital signal controller (DSC) with a 70 MIPS dsPIC33E core running at up to 60 MHz (MIPS rated up to 70 with 3.3V operation), 512 KB of flash memory, 52 KB of SRAM, and integrated USB, packaged in a 144-pin TQFP (20x20 mm) qualified for -40C to +125C extended temperature operation. A digital signal controller combines the computational throughput of a digital signal processor (DSP) with the peripheral set, ease of use, and development ecosystem of a microcontroller (MCU). Within the power-management hierarchy of embedded systems, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred architecture for high-speed closed-loop control such as field-oriented motor control, digital power conversion, and digital audio processing. Key features of this part include the 16-bit dsPIC33E CPU with DSP engine (single-cycle MAC, 40-bit accumulators, dual operand fetch), 512 KB of self-programmable flash supporting 1,000 erase/write cycles, 52 KB of on-chip SRAM, and 15 DMA channels that offload peripherals from CPU intervention. On-chip USB provides direct connectivity to hosts and peripherals, while high-speed PWM modules serve digital power and motor drive topologies. Architecturally, the dsPIC33EP series uses an enhanced Harvard architecture with a 16-bit data path and 23-bit address space. The DSP engine supports fractional and integer MAC operations, enabling execution of digital filter algorithms, high-speed precision digital control loops, and digital speech processing at deterministic cycle counts. Typical applications include precision brushless DC and PMSM motor control, digital AC-DC and DC-DC power supplies, USB-enabled instrumentation, and industrial gateways where a 3.3V, extended-temperature (-40C to +125C) controller with DSP throughput is required. Design consideration: budget flash and RAM headroom - while 512 KB flash and 52 KB RAM are ample for most control loops, USB stack plus bootloader combinations can consume 20-30 KB of flash, so plan partitions early. This page synthesizes distributor pricing (as of 2026-09-25), same-family drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU814-I/PH

DSPIC33EP512MU814-I/PH - 70 MIPS DSC, 512KB Flash, USB, 2x CAN | Microchip

The Microchip Technology DSPIC33EP512MU814-I/PH is a 16-bit digital signal controller (DSC) delivering 70 MIPS from a 60 MHz dsPIC33E core, with 512 KB (170K x 24) of FLASH program memory, 52 KB of RAM, and integrated USB and dual CAN modules, housed in a 144-pin TQFP (16x16 mm, PH) package rated for -40C to +85C operation. A digital signal controller combines the compute architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. In the semiconductor hierarchy, the dsPIC33EP512MU814 sits within the dsPIC33E family of DSCs, under Microchip's broader 16-bit microcontroller portfolio, targeting real-time embedded control where both fast math (MAC, DSP instructions) and rich peripherals are required in a single chip. Key features include a modified Harvard architecture with a 16-bit data path and 24-bit instructions, linear program addressing, dual CAN 2.0B modules, a full-speed USB 2.0 device module, and 15-channel DMA for moving data without CPU intervention. Up to 122 general-purpose I/O lines and high-speed PWM outputs make the device especially suited to precision motor control and digital power conversion, where deterministic interrupt latency and DSP capability matter. Technically, the dsPIC33E core integrates an enhanced DSP engine with single-cycle MAC and 40-bit wide accumulators, plus flexible clocking (internal FRC, primary oscillator, PLL) that lets designers trade power against performance. The peripheral ecosystem includes multiple UART, SPI and I2C modules, input capture and output compare channels, and a 10-bit ADC suited to current and voltage sensing loops in motor drives and power supplies. Typical applications include dual-motor servo and BLDC drives, industrial inverters and solar converters (the family is explicitly marketed for DSC with dual motor control, dual CAN, USB), automotive-adjacent industrial nodes via the CAN interfaces, and USB-connected instruments requiring substantial flash for protocol stacks. Design consideration: use any PGECx/PGEDx pair consistently for ICSP programming and debugging - for example PGEC2 must pair with PGED2 - and connect all VDD/VSS pins per the datasheet to avoid erratic behavior. Budget flash and RAM carefully; the 52 KB RAM is generous for its class but shared between X and Y data spaces. This page synthesizes distributor pricing and availability signals, same-family drop-in alternatives, and practical design notes in one place - information not consolidated in the Microchip datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP512MU814-I/PL

DSPIC33EP512MU814-I/PL - 16-bit DSC, 512KB Flash | Microchip

The Microchip DSPIC33EP512MU814-I/PL is a 16-bit digital signal controller (DSC) from the dsPIC33EP family with 512 KB (536 KB linear-addressed) program flash, 52 KB of RAM, a 70 MIPS dsPIC DSC core running at up to 60 MHz, and 122 general-purpose I/O lines, housed in a 144-pin LQFP (20x20 mm) package. A digital signal controller combines the computational architecture of a DSP with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, the DSC sits at the top of the 16-bit MCU class: it executes single-cycle MAC and DSP instructions, making it a natural upgrade path from a general-purpose microcontroller when control loops become computationally demanding, such as in digital power conversion, sensor fusion, or motor field-oriented control. Key features include the high-speed PWM module with complementary outputs and dead-time insertion for motor drives and digital power supplies, an integrated full-speed USB 2.0 device peripheral, dual CAN 2.0B (ECAN) modules, up to four UARTs, up to three SPI and three I2C peripherals, and a Data Converter Interface (DCI) for audio codecs. The industrial temperature grade (-I) covers -40C to +85C operation at 3.3V. Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with 16-bit data and 24-bit instructions, hardware DSP multiply-accumulate units, and a 16-channel DMA controller that offloads data movement from the CPU, keeping interrupt latency deterministic in fast control loops. Typical applications include brushless DC and PMSM motor control, digital SMPS and LLC converters, USB-connected industrial instruments, audio and speech processing using the DCI, and CAN-networked automation nodes. Design consideration: this device is known to be sensitive to crosstalk between PGEC and PGED programming lines; a small 20 pF capacitor from PGEC to VSS placed close to the chip improves in-circuit debugging reliability. This page synthesizes distributor pricing data, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP502-E/SO

DSPIC33EP64GP502-E/SO - 16-bit DSC, 60 MIPS, 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP502-E/SO is a 16-bit Digital Signal Controller (DSC) delivering 60 MIPS from a 64KB (22K x 24) Flash and 8KB RAM, housed in a 28-pin SOIC package with an extended -40C to +125C operating temperature range. A Digital Signal Controller combines the deterministic control of a microcontroller with the mathematical throughput of a DSP. In the power-management hierarchy, the dsPIC33EP family sits between general-purpose MCUs and dedicated DSPs, integrating a 16-bit pipeline core, high-speed PWM modules, and advanced analog peripherals in a single chip. This makes DSCs the default choice for closed-loop digital power and motor control systems. Key features of the DSPIC33EP64GP502 include the 70 MIPS-class dsPIC33E core running at 60 MIPS here, an ADC configurable as 10-bit at 1.1 Msps with four sample-and-hold circuits or 12-bit at 500 ksps with one S&H, three integrated operational amplifiers, four analog comparators, a CAN module, and peripheral-triggered CTMU for charge-time measurement. Six analog inputs are available on the 28-pin device. The advanced analog integration eliminates external op-amp stages for current-sense amplification and comparator-based protection, reducing BOM count in digital power supplies. The high-speed PWM module supports complementary outputs with dead-time insertion, essential for half-bridge and full-bridge topologies. Programmable Digital Filter and PTG (Peripheral Trigger Generator) offload timing-critical tasks from the CPU. Typical applications include digital switched-mode power supplies, brushless DC and PMSM motor drives, battery chargers, power factor correction stages, and industrial sensing front-ends exploiting the CTMU. A key design consideration is the 3V to 3.6V supply requirement; plan level-shifting for 5V legacy I/O, and place the analog supply decoupling per the Microchip datasheet recommendations to preserve ADC accuracy at 1.1 Msps. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP502-E/SP

DSPIC33EP64GP502-E/SP - 16-bit DSC 60 MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP502-E/SP is a 16-bit Digital Signal Controller (DSC) delivering 60 MIPS core performance with 64 KB Flash (22K x 24) and 8 KB SRAM, housed in a 28-pin SPDIP through-hole package rated for the extended -40C to +125C temperature range. A Digital Signal Controller combines the deterministic architecture of a microcontroller with DSP-grade multiply-accumulate capability in a single core. In the power-management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice when an application needs both control-loop code and math-intensive signal processing without a two-chip solution. Key features include the 60 MIPS dsPIC33E core, High-Speed PWM peripherals for digital power conversion, CAN 2.0B communication, three integrated op amps, four comparators, a Peripheral Trigger Generator (PTG) and a Charge Time Measurement Unit (CTMU). Integrating op amps and comparators on-chip reduces external analog component count in current-sense and protection circuits. The dsPIC33EP series architecture pairs a 16-bit pipelined core with a single-cycle 16x16 MAC/DC DSP engine, supporting fractional and integer arithmetic. The 64 KB of self-programmable Flash supports field firmware updates, while 8 KB of SRAM handles control-loop state and communication buffers. Supply voltage is 3.0 V to 3.6 V. Typical applications include digital power supplies, battery chargers, PFC stages, motor control (BLDC/PMSM/stepper), and industrial sensing systems that exploit the CTMU for capacitive or time-domain measurements. Design consideration: the /SP SPDIP package is ideal for prototyping and low-volume through-hole assemblies; for mass-production SMT, pin-function-equivalent SOIC-28 (/SO) and QFN-U28 (/MM) siblings use the same die but different footprints. This page synthesizes distributor availability, drop-in family alternatives, and practical design guidance not consolidated in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP502-E/SS

DSPIC33EP64GP502-E/SS - 16-bit DSC 60 MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP502-E/SS is a 16-bit digital signal controller (DSC) delivering 60 MIPS performance from a 64 KB (22K x 24) Flash program memory and 8 KB SRAM, housed in a 28-pin SSOP (SS) surface-mount package with an extended -40C to +125C operating temperature range. It operates from a single 3V to 3.6V supply. A digital signal controller combines the deterministic control of a microcontroller with the math throughput of a DSP. Within the power-management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs, making the dsPIC33EP family a common choice where control loops and signal processing coexist in one chip. Key features include the dsPIC33E 16-bit core with DSP engine (barrel shifter, 40-bit accumulators, single-cycle MAC), high-speed PWM outputs suited to power conversion and motor control, on-chip op-amp and advanced analog peripherals, and multiple serial interfaces. The extended E temperature grade supports industrial environments where standard 0C to +70C parts cannot be trusted. Architecturally, the device pairs a pipelined 16-bit RISC CPU with a DSP accelerator and 24-bit instruction word Flash, achieving the 60 MIPS rating from an internal PLL-fed clock. Programming and debugging are handled through Microchip MPLAB X IDE with the MPLAB Snap or PICkit in-circuit debuggers, as documented on the Microchip product page. Typical applications include digital power supplies (PLL, PFC), brushless DC and permanent-magnet motor control, sensor signal conditioning, and general embedded control that benefits from DSP math. The 28-SSOP footprint suits compact, cost-sensitive industrial boards. For design, decouple all VDD pins with 0.1 uF ceramics, provide the dedicated VCAP connection per the manufacturer datasheet, and budget Flash/RAM headroom since 64 KB/8 KB is fixed on this fixed-memory part. This page synthesizes distributor availability data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP502-I/MM

DSPIC33EP64GP502-I/MM - 16-Bit 70 MIPS DSC QFN-28 | Microchip

The Microchip Technology DSPIC33EP64GP502-I/MM is a 16-bit digital signal controller (DSC) with a 70 MIPS dsPIC33E core, 64 KB (22K x 24) of Flash program memory and a QFN-28-EP (6x6 mm) surface-mount package. It operates from a 3 V to 3.6 V supply across an industrial -40C to +85C temperature range. A digital signal controller combines the compute architecture of a digital signal processor (DSP engine, hardware multiply-accumulate, DSP instruction set) with the peripheral integration of a microcontroller (MCU). In the system hierarchy, this part sits between general-purpose MCUs and dedicated DSPs: it is a 16-bit embedded processor optimized for control loops that also need math-intensive signal processing, such as motor control, digital power conversion, and sensor conditioning. Key features include the high-speed 70 MIPS core with DSP and fixed-point instructions, high-speed PWM peripherals suited for power conversion, multiple UART/SPI/I2C serial interfaces, and general-purpose timers. The dsPIC33EP GP family also integrates advanced analog and, on this die, on-chip peripheral facilities such as the Peripheral Trigger Generator family features. The QFN-28-EP exposed-pad package improves thermal performance and grounding in compact boards. Technically, the device executes from Flash with 24-bit instruction words, offers interrupt-prioritized deterministic response for control loops, and supports In-Circuit Serial Programming (ICSP) via PGECx/PGEDx pin pairs plus In-Circuit Emulation debugging. Clock options include an internal fast RC oscillator and external crystal/PLL configurations reaching 70 MIPS core operation from a 3.0-3.6 V rail. Typical applications include brushless DC (BLDC) and permanent-magnet motor control, switch-mode power supplies and digital lighting, industrial automation nodes, and DSP-enhanced sensing such as audio processing and metering. A key design consideration is power integrity: the VCAP/VDDCORE pin requires the datasheet-specified external capacitor for the internal regulator, and all VDD/VSS pairs plus the exposed pad must be connected for reliable operation. This page synthesizes distributor pricing (from $2.99 as of 2026-09-25 at LCSC), pin-compatible dsPIC33EP alternatives, and practical design notes not found on the standard product page.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP502-I/SP

DSPIC33EP64GP502-I/SP - 16-bit 70 MIPS DSC 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP502-I/SP is a 16-bit digital signal controller (DSC) delivering 70 MIPS performance from its dsPIC33E core, with 64KB (22K x 24) of flash program memory and a 28-pin SPDIP (SP) through-hole package, industrial temperature rated from -40C to +85C. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and deterministic interrupt structure of a microcontroller. Within Microchip's hierarchy, the dsPIC33EP64GP502 sits in the general purpose (GP) dsPIC33E family: a DSC is a superset of an MCU, adding a DSP engine, high-speed ADC, and advanced PWM for mixed signal-control workloads. Key features include the 70 MIPS, 16-bit pipelined core with DSP instruction support, up to 512KB flash scalability across the family (64KB on this part), CAN2.0b communication, a Charge Time Measurement Unit (CTMU), and Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. The part operates from a single 3.0V to 3.6V supply and provides multiple general-purpose 16-bit timers and rich I/O. Technical strengths center on superior ADC performance in this class and the high code density of the modified Harvard architecture, letting developers run closed-loop control plus communication stacks without external components. Advanced analog and high-speed PWM peripherals suit motor control and power conversion directly. Typical applications include digital power supplies, brushless DC and PMSM motor control, industrial sensing and automation nodes, and general-purpose embedded control where 70 MIPS headroom is needed. Design consideration: the part requires a VCAP/VDDCORE stabilizing capacitor on its internal 2.5V core regulator pin, and all VDD/VSS pairs must be connected and decoupled for reliable operation. This page adds value beyond the datasheet by synthesizing drop-in same-family alternatives, FAQ-driven selection guidance, and application pairings in one reference.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP502T-I/SS

DSPIC33EP64GP502T-I/SS - 16-bit DSC 70MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP502T-I/SS is a 16-bit general purpose digital signal controller (DSC) delivering up to 70 MIPS core performance at 60 MHz maximum clock frequency, with 64 KB (22K x 24) of Flash program memory and 8 KB of RAM, housed in a 28-pin SSOP surface-mount package with an industrial -40C to +85C operating range. A digital signal controller is a hybrid device that combines the computational power of a digital signal processor (DSP) with the peripheral integration and control-oriented architecture of a microcontroller (MCU). Within the power-management hierarchy of embedded systems, the dsPIC33E family sits above basic 8-bit PIC MCUs and complements 32-bit ARM MCUs, occupying the product class of 16-bit Digital Signal Processors & Controllers - DSP, DSC used in real-time control loops and signal processing. Key features include the highest-speed 70 MIPS dsPIC33E core with excellent code density, superior ADC performance for analog acquisition, CAN communication for industrial and automotive networking, the Charge Time Measurement Unit (CTMU) for capacitive touch and time-of-flight measurement, and the Peripheral Trigger Generator (PTG) for autonomous, hardware-timed peripheral sequencing. Integrated analog support such as comparators further reduces external component count. Technically, the device uses a CMOS process with a 24-bit-wide program memory architecture (instruction word) paired with a 16-bit data bus, a DSP engine with barrel shifter for efficient data manipulation, and multiple low-power modes that suit battery-operated designs. The GP (general purpose) family variant emphasizes general-purpose peripherals for high-end general purpose applications. Typical applications include industrial motor control and power conversion, embedded sensing and measurement systems using CTMU, and general-purpose control nodes that require CAN bus connectivity. The 28-pin SSOP footprint fits compact, cost-sensitive boards. Design consideration: choose the I-grade (-40C to +85C) part for industrial environments; the E-grade (-40C to +125C) sibling, DSPIC33EP64GP502T-E/SS, is pin-compatible when extended temperature is required. Budget 64 KB of program memory carefully if migrating from larger Flash family members. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP503-E/M5

DSPIC33EP64GP503-E/M5 - 16-bit 60 MIPS DSC, 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP503-E/M5 is a 16-bit digital signal controller (DSC) delivering up to 60 MIPS core performance with 64KB (22K x 24) of Flash program memory and 8KB of RAM, housed in a 36-pin VTLA/UQFN exposed-pad (5x5 mm) package rated for -40C to +125C operation. A digital signal controller combines the computational architecture of a digital signal processor (DSP) with the peripheral integration and ease of use of a microcontroller (MCU). Within the power management hierarchy of embedded systems, the dsPIC33E family sits between general-purpose MCUs and dedicated DSPs, offering single-cycle MAC, barrel shifting, and hardware divide alongside familiar peripherals such as UART, SPI, I2C, and CAN. Key features of the DSPIC33EP64GP503-E/M5 include an integrated CAN 2.0B module for industrial and automotive networking, three on-chip operational amplifiers (OpAmps) that reduce external analog component count, four analog comparators, a Charge Time Measurement Unit (CTMU) for capacitive touch and precise time measurement, and a Peripheral Trigger Generator (PTG) for autonomous peripheral sequencing. Hi-Speed PWM outputs make it well suited for power conversion and motor control topologies. The dsPIC33E core provides a 16-bit modified Harvard architecture with a 24-bit instruction word, four DMA channels that move data without CPU intervention, and five 16-bit timers. These resources enable deterministic real-time behavior in control loops running at multi-kilohertz update rates. Typical applications include industrial motor control (BLDC, PMSM, AC induction), digital power supplies and power factor correction, CAN-based automotive and industrial sensor nodes, and touch-sensing interfaces leveraging the CTMU. Design consideration: the -E temperature variant supports extended ambient operation to +125C, but thermal design of the exposed-pad UQFN package is critical at 60 MIPS operation; solder the thermal pad to a copper pour for reliable junction temperatures. This page synthesizes distributor pricing context, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33EP64GP503-E/TL

DSPIC33EP64GP503-E/TL - 16-bit DSC 60MIPS 64KB Flash | Microchip

The Microchip Technology DSPIC33EP64GP503-E/TL is a 16-bit Digital Signal Controller (DSC) delivering 60 MIPs performance, 64KB (22K x 24) of Flash program memory, and 8KB of RAM, housed in a 36-pin VTLA (5x5 mm) QFN package rated for extended -40C to +125C operation. A Digital Signal Controller combines the computational throughput of a DSP with the peripheral integration and control peripherals of a microcontroller, sitting within the hierarchy: DSC -> 16-bit microcontroller -> embedded processor -> semiconductor. dsPIC33E devices execute a modified Harvard architecture instruction stream from Flash in a single cycle, making them a common choice where math-intensive control loops replace a separate MCU plus DSP pair. Key differentiating features of the dsPIC33EP64GP503 include three integrated operational amplifiers, four analog comparators, an 8-channel 10-bit/12-bit ADC with high sample rates, a CAN 2.0B controller, hi-speed PWM outputs, the Peripheral Trigger Generator (PTG), and the Charge Time Measurement Unit (CTMU) for capacitive touch and precise time measurement. Architecturally, the dsPIC33E core pairs a 16-bit CPU with DSP engine features including single-cycle MAC, 40-bit accumulators, and dual operand fetch, enabling true DSP-class filtering and transform math. DMA channels move ADC results without CPU intervention, which keeps control-loop jitter low in digital power and motor control systems. Typical applications include digital power supplies (PFC, LLC), BLDC/PMSM motor control leveraging the hi-speed PWM, CAN-based industrial and automotive sensor nodes, and capacitive-touch or analog sensing front ends exploiting the op amps, comparators, and CTMU. Design consideration: the E-suffix temperature grade (-40C to +125C) carries a price premium over the I-suffix; specify E grade only when the thermal environment or automotive requirement demands it. Supply 3.0V to 3.6V on VDD with proper decoupling and verify Flash endurance against the datasheet specification for high-rewrite applications. This page synthesizes verified distributor data, drop-in family alternatives, and application-level design notes in one place, adding selection value beyond the raw Microchip datasheet.

طلب عرض سعر اتصل بنا

الفئات الفرعية

المنتجات (39,000+)

DSPIC33EP512MC806-E/PT - 512KB Flash 16-bit DSC, 64-TQFP | Microchip

DSPIC33EP512MC806-I/MR - 70 MIPS 16-bit DSC, 512KB Flash | Microchip

DSPIC33EP512MC806-I/PT - 70 MIPS 16-bit DSC, 512KB Flash | Microchip

DSPIC33EP512MC806T-I/PT - 70 MIPS DSC 512KB Flash TQFP-64 | Microchip

DSPIC33EP512MU810-E/BG - 16-bit 70 MIPS DSC, 512KB Flash | Microchip

DSPIC33EP512MU810-E/PF - 16-bit DSC, 70 MIPS, 512KB Flash | Microchip

DSPIC33EP512MU810-E/PT - 16-bit DSC 60 MIPS USB TQFP-100 | Microchip

DSPIC33EP512MU810-I/BG - 16-bit 70 MIPS DSC, 512KB Flash | Microchip

DSPIC33EP512MU810-I/PF - 16-bit DSC 70 MIPS USB 2xCAN | Microchip

DSPIC33EP512MU810-I/PT - 16-bit DSC 70 MIPS 512KB Flash | Microchip

DSPIC33EP512MU810T-I/BG - 70 MIPS DSC, 512KB Flash | Microchip

DSPIC33EP512MU810T-I/PT - 16-bit 70 MIPS DSC, 512KB Flash USB CAN | Microchip

DSPIC33EP512MU814-E/PH - 16-bit 70 MIPS DSC, 512KB Flash | Microchip

DSPIC33EP512MU814-E/PL - 16-bit DSC 60MHz 512KB USB | Microchip

DSPIC33EP512MU814-I/PH - 70 MIPS DSC, 512KB Flash, USB, 2x CAN | Microchip

DSPIC33EP512MU814-I/PL - 16-bit DSC, 512KB Flash | Microchip

DSPIC33EP64GP502-E/SO - 16-bit DSC, 60 MIPS, 64KB Flash | Microchip

DSPIC33EP64GP502-E/SP - 16-bit DSC 60 MIPS 64KB Flash | Microchip

DSPIC33EP64GP502-E/SS - 16-bit DSC 60 MIPS 64KB Flash | Microchip

DSPIC33EP64GP502-I/MM - 16-Bit 70 MIPS DSC QFN-28 | Microchip

DSPIC33EP64GP502-I/SP - 16-bit 70 MIPS DSC 64KB Flash | Microchip

DSPIC33EP64GP502T-I/SS - 16-bit DSC 70MIPS 64KB Flash | Microchip

DSPIC33EP64GP503-E/M5 - 16-bit 60 MIPS DSC, 64KB Flash | Microchip

DSPIC33EP64GP503-E/TL - 16-bit DSC 60MIPS 64KB Flash | Microchip