الدوائر المتكاملة

DSPIC33FJ12GP202-I/ML

DSPIC33FJ12GP202-I/ML - 16-bit DSC, 40 MIPS, 28-QFN | Microchip

The Microchip Technology DSPIC33FJ12GP202-I/ML is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering 40 MIPS of processing performance in a 28-pin QFN (6x6 mm) package. It integrates a high-performance dsPIC33F CPU core with DSP engine, on-chip Flash program memory and SRAM, a 10-bit/12-bit ADC, multiple timers, and 21 general-purpose I/O pins. The supply range is 3.0 V to 3.6 V, and the part carries the -I (industrial) temperature grade of -40C to +85C. A Digital Signal Controller (DSC) is a hybrid class of microcontroller that pairs a deterministic 16-bit MCU core with a single-cycle multiply-accumulate (MAC) DSP engine. In the broader taxonomy, DSCs belong to microcontrollers -> embedded controllers -> signal-processing ICs, sitting between classical MCUs (no DSP throughput) and standalone DSPs (no MCU peripherals). The dsPIC33F family specifically targets cost-sensitive real-time control loops where the host MCU must also run a Kalman filter, an FFT, a power-control compensator, or audio/voice codecs concurrently with housekeeping tasks. Key features of the DSPIC33FJ12GP202-I/ML include up to 12 KB of Flash program memory, 1 KB of SRAM, a 10-bit A/D converter with up to 10 channels at 500 ksps, two comparators, a UART, an SPI, and an I2C port. The DSP engine executes a 16x16-bit MAC in one cycle, supports fractional (1.15) and integer arithmetic, and offers zero-overhead looping for FIR/IIR filter primitives. The CPU achieves deterministic 25 ns instruction cycle at 40 MIPS, with an on-chip 8 MHz internal RC oscillator that can be multiplied by the on-chip PLL. Typical applications include switched-mode power supply (SMPS) digital control, motor control for small BLDC/PMSM fans and pumps, sensor conditioning, audio processing (echo cancellation, equalization, noise suppression), and industrial sensor interfaces. The 40 MIPS budget is sufficient for running an FOC motor loop, a digital Class-D amplifier compensator, or a predictive maintenance vibration analysis alongside system management code. When designing with this device, ensure decoupling is generous (100 nF + 10 uF near VDD/AVDD pins) and that analog and digital ground planes are split under the QFN pad. The exposed thermal pad must be soldered to a copper pour of at least 1 sq. inch for reliable thermal performance. Programming is supported via ICSP over PGECx/PGEDx pins, and the part is compatible with the MPLAB X IDE, XC16 compiler, and Microchip's MPLAB Xpress cloud toolchain. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not all available from a single distributor page.

طلب عرض سعر اتصل بنا

DSPIC33FJ12GP202-I/SO

DSPIC33FJ12GP202-I/SO - 16-bit DSC, 40MIPS, 28-SOIC | Microchip

The Microchip DSPIC33FJ12GP202-I/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F general-purpose family, integrating a high-performance DSP engine with a single-cycle MCU core at up to 40 MIPS (10 MIPS per MHz when clocked at 40 MHz). Housed in a 28-pin SOIC package, it delivers DSP capability in a compact, surface-mount footprint with 21 programmable digital I/O pins. A Digital Signal Controller (DSC) is a hybrid microcontroller that combines a deterministic MCU instruction set with a dedicated DSP engine (single-cycle MAC, dual 40-bit accumulators, barrel shifter). It sits in the hierarchy: DSC -> microcontroller -> embedded processor -> semiconductor. DSCs are used where MCU bit-banging cannot meet real-time signal-processing bandwidth but a full DSP processor is overkill. Key features include 12 KB Flash program memory, 1 KB SRAM data memory, on-chip 16-bit timers, a 10-bit ADC with up to 1 Msps, plus DSP-oriented peripherals such as a motor-control PWM module (typical for the GP2 family naming). The device operates from 3.0 V to 3.6 V, supports industrial -40C to +85C, and offers 5V-tolerant digital inputs with 4 mA sink on all I/O pins for direct interface to external logic. The architecture is Harvard-based, with separate program and data buses, allowing simultaneous fetch of an instruction and a data operand. The DSP engine uses two 40-bit accumulators and a single-cycle 16x16-bit MAC, enabling efficient implementation of control loops, digital filters (FIR/IIR), and power-conversion math such as PID and space-vector modulation without software emulation overhead. Typical applications include digital power conversion (SMPS, PFC, LLC), LED lighting drivers, motor control (BLDC, PMSM, sensored/sensorless), sensor signal conditioning, audio processing, and industrial automation. The part is supported by Microchip's MPLAB X IDE, MPLAB XC16 compiler, and dsPIC33 DSP library for filter, FFT, and motor-control primitives. Designers should plan around the 28-pin SOIC budget, route VDD/VSS pairs with decoupling, and use Peripheral Pin Select to remap digital functions. For firmware migration, code is portable to dsPIC33FJ12GP201 (smaller Flash variant in the same family) and to PIC24F/H MCUs that share peripherals. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and design notes not found in the manufacturer datasheet, giving engineers an actionable buying and engineering reference in one place.

طلب عرض سعر اتصل بنا

DSPIC33FJ12GP202-I/SP

DSPIC33FJ12GP202-I/SP - 16-Bit DSC, 40 MIPS, 12KB Flash | Microchip

The Microchip Technology DSPIC33FJ12GP202-I/SP is a 16-bit Digital Signal Controller (DSC) in the dsPIC33F family, delivering up to 40 MIPS of processing performance with an integrated DSP engine, packaged in a 28-pin SPDIP (Skinny Plastic DIP) through-hole format. The device integrates 12 KB of Flash program memory and 1 KB of RAM, providing the headroom required for digital-filter, control-loop, and motor-control firmware on a single chip. It is qualified for the industrial -40C to +85C operating range (I-temp suffix). A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP), combining deterministic interrupt-driven control with single-cycle MAC (multiply-accumulate) instructions for fixed-point DSP workloads. Within the broader hierarchy, this part sits as: dsPIC33F -> dsPIC33F General Purpose family -> 16-bit DSC -> microcontroller -> embedded processor -> semiconductor. The DSP engine operates on 16-bit data with 40-bit accumulators, giving the device the numerical headroom needed for cascaded biquad filters, FFT kernels, and PID-style compensators. Key features include 40 MHz maximum operating frequency (50 ns instruction cycle), 21 general-purpose I/O pins shared with peripheral functions, an on-chip 10-bit ADC with up to 1.1 Msps conversion rate, plus Motor-Control PWM, Input Capture, Output Compare, UART, SPI, I2C, and a 16-bit Timer module. Code security via Flash code-protect and a 16-bit wide instruction path round out the device. The 3.0 V to 3.6 V supply range and 21 I/O pins are characteristic of the GP (General Purpose) sub-family. Architecturally, the dsPIC33FJ12GP202 uses a Harvard architecture with separate program and data paths, allowing the DSP engine to fetch data while the CPU prefetches the next instruction. This dual-pipeline design eliminates stalls in tight DSP loops and supports zero-overhead looping, which is essential for deterministic real-time control. The on-chip 10-bit ADC and dedicated PWM modules are tuned for closed-loop motor and power-conversion feedback. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) sensorless field-oriented control (FOC), switched-mode power supply (SMPS) digital control loops, sensor signal conditioning with on-chip FIR/IIR filtering, and industrial sensor-interface nodes. The 12 KB program-memory budget is well-matched to small real-time control loops without requiring external memory. Pair this DSC with a gate-driver IC and a three-phase inverter stage to build a complete low-voltage motor drive. When designing with this part, place the 28-pin SPDIP socket on a 0.1-inch grid and provide a local 10 uF + 0.1 uF decoupling pair within 5 mm of VDD/AVDD. Use the on-chip FRC oscillator with PLL for free-running 40 MIPS operation, or attach an external 8 MHz crystal for precision timing in motor-control PWM modules. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33FJ12GP202-I/SS

DSPIC33FJ12GP202-I/SS - 16-bit DSC, 12KB Flash, 40 MIPS | Microchip

The Microchip DSPIC33FJ12GP202-I/SS is a 16-bit Digital Signal Controller (DSC) in the dsPIC33F family, offering 12 KB of Flash program memory, 1 KB of RAM, and 21 I/O pins housed in a 28-pin SSOP package. Operating at up to 40 MIPS with a 40 MHz oscillator, the device combines a high-performance DSP engine with a microcontroller core, making it suitable for embedded control and signal-processing tasks in industrial and consumer products. A Digital Signal Controller (DSC) is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP). It executes deterministic control loops while also running MAC-style DSP operations on streaming data. The dsPIC33F family sits inside the broader dsPIC33 hierarchy (16-bit DSC) and is part of Microchip's larger 16-bit MCU/DSC portfolio, which includes the PIC24F/H microcontrollers and dsPIC30F predecessors. The 28-pin SSOP footprint targets cost-sensitive applications that need DSP horsepower without migrating to larger packages. Key features include a 16-bit modified Harvard architecture with single-cycle MAC, hardware multiply/divide, Peripheral Pin Select (PPS) for flexible I/O mapping, a 10-bit ADC up to 500 ksps, multiple timers, UART/SPI/I2C peripherals, and nanoWatt power-saving modes. The Flash memory supports self-programming for in-field firmware updates, and the instruction set is optimized for both C and assembly DSP code. Technically, the device integrates a 24-bit-wide instruction path with 16-bit data paths, supports fractional and integer arithmetic, and provides deterministic interrupt latency. The 40 MIPS throughput at 3.3 V enables real-time filtering, motor-control loops, and sensor-fusion algorithms. The PPS remap feature allows nearly every digital peripheral to be assigned to multiple pins, simplifying PCB routing and BOM reuse across product variants. Typical applications include BLDC and stepper motor control, digital power conversion (SMPS), sensor conditioning and filtering, audio processing, industrial automation, and low-cost consumer DSP subsystems such as LED lighting controllers and uninterruptible power supply (UPS) front ends. The 21 I/O count supports moderate pinout needs without forcing a jump to a larger package. Design considerations include a 3.0 V to 3.6 V supply range, careful decoupling of AVDD/AVSS for ADC accuracy, and exposure to ESD events through proper IO guard-ring layout. For battery-powered uses, the nanoWatt modes can drop quiescent current dramatically during idle. This page synthesizes distributor stock and pricing data, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet itself, giving engineers a single source for sourcing and substitution decisions.

طلب عرض سعر اتصل بنا

DSPIC33FJ12GP202T-I/ML

DSPIC33FJ12GP202T-I/ML - 16-bit DSC, 40 MIPS, 12KB Flash | Microchip

The Microchip Technology DSPIC33FJ12GP202T-I/ML is a 16-bit Digital Signal Controller (DSC) that combines the performance of a DSP with the simplicity of a microcontroller, delivering 40 MIPS at up to 40 MHz and integrating 12 KB (12K x 8) of on-chip Flash program memory together with 1 KB of SRAM, all housed in a compact 28-pin QFN (6x6 mm) package. As part of the dsPIC33F general-purpose family, the device offers seamless migration options to PIC24F, PIC24H MCUs and dsPIC30F DSCs in similar pinouts, enabling designers to scale performance without redesigning the board. A Digital Signal Controller (DSC) is a hybrid architecture that augments a microcontroller's deterministic control peripherals with a true DSP engine capable of single-cycle MAC operations. DSCs sit hierarchically within the broader class of microcontrollers (MCU), which themselves belong to embedded processors, ultimately under the umbrella of semiconductors. They are typically deployed in closed-loop control and signal-conditioning applications where the math throughput of a DSP is needed alongside the interrupt-driven determinism of an MCU. Key differentiating features of the DSPIC33FJ12GP202T-I/ML include a high-performance modified Harvard CPU with a hardware multiplier, nanoWatt technology for power-managed sleep modes, 16-bit wide data path, and a peripheral set tailored to motor control and power conversion (the GP-family designation reflects this general-purpose emphasis). The integrated DSP engine executes single-cycle 16x16 MAC operations, enabling efficient implementation of digital filters, FFT kernels, PID loops, and field-oriented control (FOC) algorithms. Communication peripherals typically include UART, SPI, I2C and selectable 10/12-bit ADC channels. From an architectural standpoint, the dsPIC33F core uses a 24-bit instruction word with two 40-bit accumulators and a 16-bit working register array, providing exceptional dynamic range for fixed-point DSP. The Flash is rated for endurance suitable for in-application self-programming and bootloader use, while the nanoWatt power-management modes (Idle, Sleep and Deep Sleep) trade wake-up latency for quiescent current reduction. Typical applications span digital power conversion (SMPS, PFC), motor control (BLDC, PMSM, stepper), sensorless field-oriented control, LED lighting drivers, uninterruptible power supplies, and consumer audio effects processing. The 28-QFN footprint is particularly suited to space-constrained designs where DSP throughput is required on a small PCB area. The "T" suffix in the MPN denotes tape-and-reel packaging, "I" denotes the industrial -40C to +85C operating temperature range, and "ML" identifies the 28-pin QFN package. When designing with this part, place a 10 uF plus 0.1 uF decoupling pair adjacent to every VDD/AVDD pin, keep the analog and digital ground returns separated until they meet at a single-point star near the QFN thermal pad, and follow Microchip's recommended in-circuit serial programming (ICSP) layout for the PGECx/PGEDx pins to avoid programming failures in production. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving an engineer a faster decision basis than the raw 28-QFN device documentation.

طلب عرض سعر اتصل بنا

DSPIC33FJ12GP202T-I/SO

DSPIC33FJ12GP202T-I/SO - 40 MIPS 16-bit DSC, 12KB Flash, 28-SOIC

The Microchip Technology DSPIC33FJ12GP202T-I/SO is a 40 MIPS 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, combining DSP performance with MCU peripherals in a 28-pin SOIC wide (300 mil) package. It integrates 12 KB of Flash program memory, 1024 bytes of SRAM, and supports up to 21 programmable digital I/O pins while operating from a 3.0V to 3.6V supply. A Digital Signal Controller (DSC) is a hybrid class of microcontroller that adds single-cycle MAC (multiply-accumulate) DSP capability to a standard MCU core. The dsPIC33F architecture fuses a modified Harvard MCU with a DSP engine, making it suitable for closed-loop control, digital filtering, and audio/voice processing. Within the broader taxonomy, this places the device in the chain: dsPIC33F -> DSC -> microcontroller -> embedded processor -> semiconductor. Key specifications include a 40 MHz maximum operating frequency (40 MIPS), 16-bit data path, integrated peripherals such as a 10/12-bit ADC, timers, UART/SPI/I2C, and PWM outputs suitable for motor control and power conversion. The device also features nanoWatt power management for sleep modes, 5V-tolerant digital inputs, and Peripheral Pin Select (PPS) that remaps digital functions onto any I/O pin. The industrial -40C to +85C temperature range supports commercial and industrial deployment. The DSP engine executes a 16x16-bit signed fractional/integer MAC in a single cycle, enabling efficient IIR/FIR filtering, FFT, and PID control loops. Combined with deterministic interrupt latency, the architecture is well suited for real-time embedded control applications. Code compatibility with the PIC24F/PIC24H MCU and dsPIC30F DSC families enables seamless firmware migration across performance points. Typical applications include digital motor control (BLDC, PMSM, stepper), switched-mode power supply (SMPS) digital control loops, sensor signal conditioning, LED lighting control, and low-cost audio effects processing. The wide SOIC-28 footprint simplifies hand-prototyping and rework in low-volume designs. When designing with this device, ensure the 3.3V rail is well decoupled (10uF bulk plus 0.1uF ceramic near each VDD/VSS pair) and that unused I/O pins are configured as outputs to minimize current draw. Code protection fuses should be evaluated for production firmware security.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201-E/P

DSPIC33FJ12MC201-E/P - 16-bit Motor Control DSC, 12KB Flash | Microchip

The Microchip Technology DSPIC33FJ12MC201-E/P is a 16-bit Digital Signal Controller (DSC) optimized for motor control applications, integrating DSP functionality with a high-performance MCU architecture in a 20-pin PDIP package. It features a 40 MHz operating speed, 12 KB Flash program memory, 1 KB RAM, and 16-bit working registers in the programmer's model. The device operates from a 3.0V to 3.6V supply and provides up to 21 I/O ports for interfacing with external motor drivers, sensors, and feedback circuits. A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller's deterministic control capabilities with a digital signal processor's computational throughput. Within the taxonomy, a DSC sits between microcontrollers and DSPs, enabling single-chip implementations of closed-loop control algorithms such as field-oriented control (FOC), space vector modulation, and PI/PID compensation. The dsPIC33FJ12MC201 belongs to the dsPIC33F family, which targets motor control, power conversion, and sensorless control applications with on-chip peripherals like PWM, ADC, and quadrature encoder interfaces. Key features of the DSPIC33FJ12MC201 include a 40 MHz clock with 16 MIPS instruction throughput, a single-cycle 16x16-bit hardware multiplier, and dual 40-bit accumulators that enable efficient DSP operations. The device includes a Flash-based program memory architecture, supporting in-circuit serial programming (ICSP) and runtime self-programming. Integrated peripherals include multiple PWM modules for three-phase motor drive, a 10-bit ADC with multiple channels, and UART/SPI/I2C communication interfaces for system connectivity. Technically, the DSPIC33FJ12MC201-E/P uses a modified Harvard architecture with separate program and data buses, allowing simultaneous fetch and access. The 'E' suffix indicates an extended operating temperature range of -40C to +125C, suitable for industrial and harsh-environment deployments. The device supports seamless migration options to PIC24F, PIC24H MCUs, and dsPIC30F DSCs in similar packages, enabling design reuse across product families. Typical applications include BLDC and PMSM motor controllers, sensorless fan and pump drivers, small appliance motor drives, and low-cost industrial automation modules. The 20-pin PDIP package suits through-hole designs, prototype boards, and educational development platforms where socketed mounting is preferred. When designing with this part, ensure proper decoupling of all VDD/VSS pairs and follow Microchip's dsPIC33F Family Reference Manual guidance for motor-control peripheral configuration. The PDIP package's larger thermal mass supports continuous operation without heatsinking at typical motor-control duty cycles. This page synthesizes distributor pricing, same-family drop-in alternatives from the Site MPN list, and practical motor-control design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201-E/SO

DSPIC33FJ12MC201-E/SO - 16-bit Motor Control DSC, 40MHz, 20-SOIC | Microchip

The Microchip DSPIC33FJ12MC201-E/SO is a high-performance 16-bit Digital Signal Controller (DSC) engineered for motor control applications, integrating DSP functionality with a 16-bit MCU architecture. The device operates at up to 40 MIPS from a 3.0V to 3.6V supply, integrates 12 KB of Flash program memory, 1 KB of RAM, and is housed in a 20-pin SOIC (7.50 mm width) wide-body package. The -E suffix indicates an extended temperature grade of -40C to +125C suitable for industrial and harsh-environment deployments. A Digital Signal Controller (DSC) is a hybrid architecture that combines the deterministic interrupt response and peripheral set of a microcontroller with the single-cycle MAC, hardware loop buffer, and DSP arithmetic engine of a digital signal processor. In the broader taxonomy it sits between an MCU and a DSP, and within Microchip's portfolio it forms part of the dsPIC33F family targeting closed-loop control, power conversion, and motor drive. The DSPIC33FJ12MC201 in particular is the smaller Flash variant of the MC201/202 motor-control family, sharing peripheral IP with the larger dsPIC33FJ32 and dsPIC33FJ64 MC devices for seamless migration. Key features of the DSPIC33FJ12MC201 include a 40 MHz internal oscillator with PLL (giving 40 MIPS throughput), dual 16-bit analog comparators with programmable reference, a 10-bit ADC with 500 ksps, motor-control PWMs with complementary outputs and programmable dead time, plus a 16-bit motor-control PWM module. Communication peripherals include I2C, SPI, and UART interfaces. The 12 KB self-programmable Flash and 1 KB SRAM enable small-footprint field-oriented control (FOC) or trapezoidal BLDC algorithms with full state-machine handling on-chip. Architecturally, the device uses a modified Harvard bus with separate 16-bit data and 24-bit instruction paths, a 16 x 16-bit single-cycle MAC, and a 40-bit accumulator with barrel shifter. The C-compiler-friendly instruction set, sixteen 16-bit working registers, and zero-overhead hardware DO/REPEAT loops make it well suited to real-time control loops where deterministic instruction counts matter. Typical applications include sensorless and sensored BLDC/PMSM motor drives, low-voltage DC motor control, fan and pump controllers, small appliance motor drive, and switched-mode power supply digital control. The AEC-Q100 qualification (per third-party listings) also opens it to automotive body and HVAC actuator subsystems. A key design tip: keep the analog AVdd rail decoupled with a 10 uF bulk plus 0.1 uF ceramic placed within 5 mm of the AVdd pin, and avoid routing the PWM outputs adjacent to the analog comparator inputs to minimize switching noise coupling into the current-sense path. This page synthesizes distributor pricing, drop-in alternatives from the same dsPIC33FJ12MC family, and practical design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201-E/SS

DSPIC33FJ12MC201-E/SS - 16-bit Motor Control DSC, 40MHz, SSOP-28 | Microchip

The Microchip DSPIC33FJ12MC201-E/SS is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, featuring 12 KB Flash program memory, 1 KB RAM, a 40 MHz operating frequency, and integrated DSP functionality optimized for motor control. Housed in a 28-pin SSOP package with the -E (Extended) temperature grade of -40C to +125C, the device integrates a high-performance 16-bit modified-Harvard MCU core with DSP extensions, a 10-bit ADC, PWM modules, and a 16-bit motor-control PWM peripheral. A Digital Signal Controller (DSC) is a hybrid processor class that combines the deterministic interrupt response and peripheral set of a microcontroller (MCU) with the multiply-accumulate (MAC) throughput and single-cycle MAC hardware of a Digital Signal Processor (DSP). The dsPIC33F family is positioned in the hierarchy as: DSC -> 16-bit DSC -> dsPIC33F family -> motor-control DSC, sitting alongside general-purpose microcontrollers (MCU) in Microchip's portfolio and serving applications that require closed-loop control at high update rates (typically 10-50 kHz PWM). Key features of this part include a 40 MIPS CPU, single-cycle 16x16 MAC, dual 40 MHz 16-bit timers, a 6-channel motor-control PWM with complementary outputs and dead-time control, a 10-bit 1.1 Msps ADC with up to 6 analog inputs, and a 21-I/O count spread across the SSOP-28 footprint. The -E temperature grade extends the operating range to +125C, making the part suitable for under-hood automotive and harsh industrial environments. The architecture uses a 24-bit instruction word with a variable-length opcode field and a 16-bit data path. Program memory is Flash with self-programming support, and data EEPROM emulation is available. The motor-control PWM supports center-aligned, edge-aligned, and multi-mode operation with hardware fault inputs, eliminating software timing jitter in critical shutdown paths. Typical applications include BLDC and PMSM motor drives, sensorless and Hall-sensor FOC fan/ pump controllers, small appliance motor control, drone ESCs, automotive body electronics (door modules, mirror adjust), and HVAC blower control. The combination of deterministic PWM and DSP throughput makes the part well suited to field-oriented control (FOC) implementations on low-cost 3-phase inverter stages. When designing with the DSPIC33FJ12MC201, ensure the VDD/VSS decoupling follows the 100 nF + bulk capacitor recommendation from the datasheet and that the motor-control PWM fault pin is wired to the gate-driver fault output for hardware shutdown latency below 1 us. Plan code size against the 12 KB Flash limit; for state-space observers or sensorless FOC, the I/P or larger Flash variants in the family may be required.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201-I/SO

DSPIC33FJ12MC201-I/SO - 16-bit Motor Control DSC, 40 MIPS | Microchip

The Microchip DSPIC33FJ12MC201-I/SO is a 16-bit Digital Signal Controller (DSC) optimized for motor-control applications, integrating DSP and MCU functionality in a single 20-pin SOIC package. It features a 40 MIPS modified Harvard architecture, 12 KB Flash program memory, 1 KB RAM, and a high-performance 16-bit timer/capture/compare/PWM subsystem tailored for brushless DC, PMSM, AC induction, and switched reluctance drives. The variant suffix "-I/SO" denotes the industrial temperature grade (-40C to +85C) and the 0.300-inch wide 20-pin SOIC package with 7.5 mil pitch. A Digital Signal Controller (DSC) is a specialized microcontroller that combines a general-purpose 16-bit MCU core with hardware-level DSP capability (single-cycle MAC, barrel shifter, dual 40-bit accumulators) and tightly integrated analog/motor-control peripherals. In the broader taxonomy, the dsPIC33F family sits between 8/16-bit PIC microcontrollers and full DSP processors; it belongs to the power management > motor control IC family and is widely used as a cost-effective bridge between fixed-point DSP and standard MCU solutions. Key specifications include up to 21 I/O pins, six PWM channels with complementary or independent outputs, a 10-bit ADC with up to 500 ksps conversion rate, and 3.0 V to 3.6 V single-supply operation. The 16-bit DSC core performs single-cycle multiply-and-accumulate operations, while dual 40-bit accumulators enable fractional arithmetic and fast Park/Clarke transforms required for sensorless vector control. Hardware fault timers and dead-time control are integrated into the PWM module, simplifying UL/IEC 60730 safety-certified drive design. Typical applications include ceiling fan and pump variable-frequency drives, low-voltage BLDC motor controllers for appliances, hobby drones and RC ESCs, sensorless PMSM controllers for e-mobility auxiliaries, and small industrial servo drives. The wide operating voltage and robust motor-control PWM make it a strong fit for 12 V / 24 V / 48 V brushless platforms requiring deterministic real-time control. When designing with this part, allocate sufficient decoupling (100 nF ceramic plus 4.7 uF bulk) close to VDD/AVDD pairs, and keep the analog ground and digital ground returns separated until they join at the exposed pad or a single-point ground. Use Microchip's MPLAB X IDE with the XC16 compiler and the dsPICE FOC or Motor Control Library to accelerate algorithm development.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201-I/SS

DSPIC33FJ12MC201-I/SS - 16-bit DSC, 40MHz, 12KB Flash | Microchip

The Microchip Technology DSPIC33FJ12MC201-I/SS is a 16-bit Digital Signal Controller (DSC) optimized for motor-control applications, delivering up to 40 MIPS from a single 3.0V to 3.6V supply in a 20-pin SSOP package. It integrates a DSP engine with a 16-bit MCU architecture, 12 KB of Flash program memory, and 1 KB of SRAM, plus a dedicated motor-control PWM peripheral set including a 6-channel PWM with complementary outputs and fault inputs. A Digital Signal Controller (DSC) is a class of microcontroller that combines traditional MCU peripherals (timers, ADC, communication ports) with on-chip DSP capability - typically a single-cycle MAC, barrel shifter, and saturating arithmetic - to execute control-loop math in real time without an external DSP chip. Within the broader taxonomy, the dsPIC33F sits between PIC24F MCUs (no DSP) and dsPIC33EP performance DSCs; for motor control it occupies the slot between general-purpose PIC24FJ devices and the higher-pin-count dsPIC33EP MCUs, making it the lowest-cost entry point into field-oriented control (FOC) on a 16-bit core. Key features include a 40 MHz clock speed (with on-chip 7.37 MHz and PLL options for 40 MIPS operation), a 10-bit ADC with a 1.1 Msps conversion rate (the dsPIC33FJ12MC201 has 4 ADC channels, the 202 variant has 9), 5-cycle interrupt latency, and low-power Idle, Sleep, and Doze modes. The device family supports migration between dsPIC33FJ12MC201 and dsPIC33FJ12MC202, and from PIC24F/PIC24H MCUs and dsPIC30F DSCs in similar pin counts, which simplifies field upgrades. Architecturally, the device uses a Harvard-class bus with 24-bit-wide instructions and 16-bit-wide data, 16 x 16 fractional/integer single-cycle MAC, and 32/16 and 16/16 divide operations. CMOS design with low-power modes and a wide operating temperature range of -40C to +85C (industrial) makes it well-suited to harsh motor-drive environments. The 20-pin SSOP (5.30 mm body, 0.65 mm pitch) package gives a small footprint while still exposing the full motor-control PWM, QEI (on the MC202), and UART/SPI/I2C peripherals. Typical applications include sensorless and sensored BLDC motor drives, PMSM field-oriented control, switched reluctance motor control, and small DC servo loops in industrial drives, appliances, and HVAC blowers. The DSP math engine and high-speed PWM make it well matched to trapezoidal and sinusoidal commutation up to a few hundred watts. Compact 24V fan controllers, e-bike torque controllers, and small-format pump drives are common end uses. When designing with the DSPIC33FJ12MC201, plan the ADC and PWM timings carefully - the 4 ADC channels limit the device to a single current-shunt topology, so users targeting two- or three-shunt FOC should consider the dsPIC33FJ12MC202 (28-pin, 9 ADC channels). The 'I' suffix denotes the industrial -40C to +85C operating range; the 'E' suffix variant extends this to -40C to +125C. This page synthesizes distributor pricing, verified drop-in alternatives in the same SSOP-20 footprint, and practical design notes that go beyond the manufacturer datasheet. Each application section provides concrete parameter alignment, not generic boilerplate.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201T-I/SO

DSPIC33FJ12MC201T-I/SO - 16-bit 40MIPS 12KB Flash Motor Control DSC | Microchip

The Microchip Technology DSPIC33FJ12MC201T-I/SO is a high-performance 16-bit Digital Signal Controller (DSC) from the dsPIC33F family optimized for motor control applications, integrating DSP functionality with a 40 MIPS MCU core in a 20-pin SOIC (SO) package. The device features 12 KB Flash program memory, 1 KB RAM, and is offered in tape and reel packaging for high-volume assembly. A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller (MCU) control loop with a Digital Signal Processor (DSP) computation engine. DSCs sit in the hierarchy: microcontroller -> DSC -> DSP -> embedded processor, and are particularly well-suited to closed-loop control tasks where both deterministic real-time response and high-rate numerical computation are required simultaneously, such as field-oriented control (FOC) of three-phase motors. Key features include 16-bit data path, 40 MIPS execution, 21 I/O pins, an integrated 6-channel PWM module with dedicated motor-control peripherals, 12-bit ADC, and operation from 3.0 V to 3.6 V. The dsPIC33FJ12MC201 is specifically architected with motor-control centric peripherals including a Motor Control PWM (MCPWM) module, quadrature encoder interface (QEI), and high-speed analog comparators, eliminating external logic in typical BLDC and PMSM drive designs. Typical applications include sensorless and sensored BLDC motor drives, PMSM servo control, ceiling fans and pumps, e-bike controllers, small appliances, and DC-DC converter digital control loops. The 20-SOIC footprint simplifies hand prototyping and rework while still supporting the motor-control PWM duty cycles needed for switching frequencies above 20 kHz. Designers should provide adequate decoupling (100 nF + 10 uF bulk) close to VDD/AVDD pins and follow Microchip's dsPIC33F motor-control reference design layouts to minimize PWM glitch injection into the ADC sampling window. The 'T' suffix indicates Tape and Reel packaging, while the 'I' suffix indicates the -40C to +85C industrial temperature grade.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC201T-I/SS

DSPIC33FJ12MC201T-I/SS - 40 MIPS Motor Control DSC | Microchip

The Microchip Technology DSPIC33FJ12MC201T-I/SS is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family optimized for motor control applications, delivering 40 MIPS at 40 MHz with 12 KB Flash and 1 KB SRAM in a 20-pin SSOP package. The part operates from 3.0 V to 3.6 V and exposes 13 I/O pins, making it suitable for compact BLDC, PMSM, AC induction, and stepper motor control boards where board area and BOM cost are tightly constrained. What is a DSC? A Digital Signal Controller (DSC) is a hybrid device that combines a microcontroller (MCU) with a digital signal processor (DSP) on a single die. In the taxonomy: DSC -> DSP+MCU hybrid -> microcontroller -> embedded processor -> semiconductor. DSCs execute deterministic motor-control algorithms like field-oriented control (FOC) and space-vector PWM at speeds that a generic MCU cannot reach, while retaining the interrupt structure, peripherals, and C-friendly toolchain of a microcontroller. The dsPIC33F family adds a 40-bit wide accumulator and dual-port SRAM, enabling 16-bit math with extended headroom for closed-loop current and torque loops. Key specifications include 12 KB on-chip Flash (11 K x 24 instruction words), 1 KB SRAM, 16-channel 10-bit ADC at 1.1 Msps (or 12-channel 12-bit ADC at 500 ksps on later revs), up to 6 PWM outputs with complementary mode and dead-band, plus a dedicated quadrature encoder interface. The device supports nanoWatt power-saving modes (idle, sleep, deep sleep), typically draws <50 mA active and low microamp sleep current, and is specified for -40 C to +85 C (industrial) per the -I suffix. The DSP engine executes one MAC per instruction cycle through its X and Y data read buses and a 40-bit dual-accumulator pipeline, allowing single-cycle FFT and IIR operations needed for sensorless FOC estimators. Hardware peripherals (PWM, ADC, QEI) are deterministic and tightly coupled to the motor-control loop, removing interrupt jitter that complicates time-critical switching on a generic MCU. Code is generated through MPLAB X IDE with the dsPIC DSC compiler suite and Motor Control Library, which ships drop-in FOC and scalar-V/Hz blocks tuned for this silicon. Typical applications include BLDC ceiling fans and HVAC blowers, low-voltage brushed-DC pumps, sensorless PMSM drives up to ~300 W, small appliances (mixers, blenders, vacuums), and battery-powered personal-mobility motors (e-bike torque-assist boards). Tape-and-reel packaging supports high-mix SMT assembly. Design consideration: route the analog ground and digital ground as a single point at the device's VSS pin and place the PWM dead-band configuration in SFR _FBCLKDIV before enabling the PWM generator to avoid first-cycle glitches. The Motor Control Library is revision-controlled; verify the algorithm revision and dsPIC DSC compiler version you re-use. This page combines distributor pricing, pinout detail, AEC-Q100-style grade indicators, and drop-in alternatives so an engineer can shortlist, validate, and order the part in a single workflow.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202-E/ML

DSPIC33FJ12MC202-E/ML - 16-Bit Motor Control DSC, 40 MIPS, 28-QFN | Microchip

The Microchip Technology DSPIC33FJ12MC202-E/ML is a 16-bit Digital Signal Controller (DSC) in the dsPIC33F family, optimized for motor-control applications and housed in a 28-pin QFN package (6x6 mm). It combines a high-performance 16-bit MCU architecture with on-chip DSP capability, achieving up to 40 MIPS throughput at a 3.3 V supply. The device integrates 12 KB of program Flash, 1 KB of SRAM, and a 16-bit nanoWatt technology power-management block, while its peripheral set includes dedicated motor-control PWM, a 10-bit ADC, and multiple timers. According to the Microchip dsPIC33FJ12MC201/202 datasheet, this part is a member of a seamless migration family that bridges to PIC24F, PIC24H MCUs and dsPIC30F DSCs in similar packages, giving designers a scalable upgrade path across motor-control platforms. What is a Digital Signal Controller? A DSC is a hybrid between a microcontroller (MCU) and a digital signal processor (DSP): it executes deterministic control loops like an MCU while also performing real-time signal processing on motor currents, sensor feedback, and audio. Within the broader taxonomy, the DSC sits below the digital signal processor family and above the general-purpose microcontroller family in the embedded-semiconductor hierarchy, which itself belongs to integrated circuits in power-management-adjacent embedded systems. Key differentiating features include the dsPIC33F core with single-cycle 16x16 MAC, dual 40-channel motor-control PWM modules with flexible duty, dead-time and fault inputs, and an extended temperature range from -40C to +125C suitable for industrial and AEC-Q100-grade environments. The integrated nanoWatt power-management block provides multiple idle and sleep modes that reduce active current draw, while 16 KB of auxiliary Flash on select variants supports self-programming for field updates. The QFN-28 package exposes a thermal pad, lowering thermal resistance and enabling compact PCB layouts for high-density drives. Architecturally the device uses a Harvard bus with separate program and data paths, a hardware multiply-accumulate engine, and a peripheral engine that offloads PWM and ADC sequencing from the core, freeing MIPS for control algorithms. The 40 MIPS sustained throughput enables sensorless Field-Oriented Control (FOC) of three-phase BLDC and PMSM motors without external DSP co-processors, while integrated op amps on select signals reduce BOM. Typical applications include low-voltage three-phase BLDC and PMSM motor drives, ceiling fans and pumps, e-bike controllers, drone ESCs, and small appliance inverters. Industrial and automotive auxiliary drives such as HVAC blowers and power-window modules also benefit from the wide temperature range and robust PWM peripherals. The compact 28-QFN footprint suits space-constrained PCBs used in LED drivers and sensor hubs. When designing with this device, ensure the input supply is decoupled with both 100 nF and 10 uF capacitors placed close to the VDD pins and that the EP (thermal pad) is soldered to a sufficiently large copper pour to meet the datasheet's 31 C/W thermal resistance target. Designers should also budget adequate PWM timer headroom when using complementary outputs with dead-time insertion to avoid shoot-through. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202-E/SO

DSPIC33FJ12MC202-E/SO - 16-bit Motor Control DSC, 12KB Flash | Microchip

The Microchip DSPIC33FJ12MC202-E/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33FJ12MC family, integrating DSP functionality with a high-performance 16-bit MCU architecture optimized for motor control. Operating at up to 40 MIPS with a 40 MHz core clock, the device integrates 12 KB of Flash program memory and 1 KB of SRAM in a 28-pin SOIC wide-body (SO) package. Its 16-bit architecture with DSP extensions delivers deterministic motor-control throughput at 3.0V to 3.6V single-supply operation. A digital signal controller (DSC) is a class of microcontroller that combines a standard MCU instruction set with a dedicated DSP engine, enabling real-time control loops, digital filtering, and power-conversion math on a single chip. Within the broader taxonomy, the dsPIC33FJ12MC202 belongs to the DSC -> microcontroller -> embedded controller -> semiconductor hierarchy, sitting between general-purpose MCUs and standalone DSPs. This architecture makes it ideal for time-critical closed-loop applications such as BLDC, PMSM, and AC induction motor drives. Key differentiating features include a 6-channel PWM module dedicated to motor control with complementary or independent output modes, a 10-bit ADC with up to 8 channels and 1.1 Msps conversion, a 16-bit timer/capture/compare block, and three 16-bit general-purpose timers. The nanoWatt power management unit provides Idle, Sleep, and Deep Sleep modes with sub-microamp standby current, allowing battery-backed designs to retain state without significant drain. Communication interfaces include UART, SPI, and I2C for telemetry and supervisory control. Typical applications cover brushless DC motor drives, sensorless PMSM controllers, low-cost field-oriented control (FOC) platforms, appliance pumps and fans, robotic servo loops, and automotive body modules. The 28-SOIC footprint simplifies PCB layout for through-hole-style prototyping while still supporting surface-mount assembly. Compared to PIC24F/H MCUs of the same pin package, the dsPIC33FJ12MC202 adds the DSP engine and dedicated PWM; relative to dsPIC30F DSCs, the '33FJ series offers faster ADC, lower power, and shorter interrupt latency. Design considerations include ensuring adequate decoupling on AVDD/VDD rails, placing the 28-SOIC on at least 4-layer PCB to keep ground bounce under control during high-current PWM switching, and using the JTAG/ICSP interface for firmware development. The -E industrial temperature grade supports -40C to +125C operation, making the part suitable for harsh-environment industrial and under-hood automotive subsystems. This page synthesizes distributor pricing, drop-in alternatives, and practical motor-control design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and design-in decisions.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202-E/SS

DSPIC33FJ12MC202-E/SS - 16-bit Motor Control DSC, 40 MIPS, 12KB Flash | Microchip

The Microchip DSPIC33FJ12MC202-E/SS is a 16-bit Digital Signal Controller (DSC) that combines high-performance DSP capability with a microcontroller architecture optimized for motor control applications, executing up to 40 MIPS from an internal oscillator and packaged in a 28-pin SSOP with 0.65 mm pitch. The device integrates 12 KB of Flash program memory, 1 KB of RAM, and a motor-control PWM module with up to six output channels supporting complementary or independent PWM modes for three-phase inverter drive. A 10-bit ADC with up to 500 ksps conversion rate, programmable 16-bit timers, and a peripheral pin-select (PPS) unit allow flexible signal routing on the small 28-pin footprint. A Digital Signal Controller (DSC) is a class of MCU that augments a standard microcontroller core with a DSP engine - a hardware multiplier-accumulator (MAC) and barrel shifter - enabling deterministic execution of control loops, digital filters, and power-conversion algorithms in a single chip. Within the broader taxonomy, the dsPIC33F family bridges 8/16-bit PIC MCUs and 32-bit devices, offering C-compiler-friendly Harvard architecture with deterministic interrupt latency and DSP instructions such as MAC, ED, and EDAC. The -E suffix indicates the -40 C to +125 C extended operating temperature grade, qualified to AEC-Q100 for automotive environments. Key differentiating specifications of the DSPIC33FJ12MC202-E/SS include the 6-output Motor Control PWM (up to 16-bit resolution with 7.5 ns dead-time control), the 500 ksps 10-bit ADC with dedicated S&H, the 40 MIPS core, and integrated op-amp comparators that interface directly to motor current-sense shunt signals. Five 16-bit timers and four DMA channels support low-CPU-overhead data movement. The PPS peripheral pin-select unit allows remapping of digital I/O functions to any of the general-purpose pins, simplifying PCB layout when motor-control signals must be routed near power stages. The architecture features separate program and data buses with 24-bit instruction words and 16-bit data paths. A 16 x 16 hardware multiplier with 40-bit accumulator resolves DSP MAC operations in one instruction cycle, making single-pole IIR filters, Park/Clarke transforms, and space-vector modulation feasible at low PWM frequencies. The instruction set is fully upward-compatible with PIC24F/H devices, easing migration to higher-pin-count motor-control families such as dsPIC33EP and dsPIC33CH. Typical applications include BLDC and PMSM sensorless or sensored motor drives, low-power field-oriented control (FOC) of three-phase induction motors, DC-DC converters, digital Class-D audio amplifiers, and automotive body-comfort motor control such as HVAC blowers and coolant pumps. The extended temperature range and AEC-Q100 qualification make it well-suited for under-hood automotive ECUs and industrial servo drives operating from 24 V or 48 V buses. When designing with this device, allocate the analog supply (AVDD) pins with adequate decoupling and route the motor-current-sense traces differentially to the on-chip op-amp comparator inputs. The PPS unit can be configured post-reset to remap peripheral functions, but pin assignments for analog peripherals and the dedicated PWM outputs are fixed per the datasheet pinout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202-I/ML

DSPIC33FJ12MC202-I/ML - 16-bit DSC, 12KB Flash, 40 MIPS Motor Control

The Microchip Technology DSPIC33FJ12MC202-I/ML is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F motor-control family, delivering 40 MIPS performance from a 40 MHz CPU clock and integrating extensive DSP functionality with a high-performance 16-bit MCU architecture in a 28-pin QFN (6x6 mm) package. The device pairs a C-compiler-friendly modified Harvard architecture with a single-cycle 16x16-bit MAC, dual 40-bit accumulators, and a 16-bit timer/capture/PWM engine optimized for variable-frequency three-phase motor commutation. A Digital Signal Controller is a hybrid between a microcontroller (MCU) and a Digital Signal Processor (DSP): like an MCU it integrates Flash program memory, SRAM, and peripherals; like a DSP it adds a single-cycle MAC engine and saturating arithmetic to implement closed-loop control loops in firmware. Within the power-electronics hierarchy, DSCs occupy the position above general-purpose MCUs and below dedicated motor-control ASSPs, sitting in the broader category of embedded control silicon (DSC -> microcontroller -> embedded processor -> semiconductor). Key features include 12 KB of Flash program memory, 1024 bytes of SRAM, an internal 7.37 MHz oscillator with PLL, a 16-bit Motor Control PWM module with up to 6 outputs and dedicated fault inputs, a 10-bit ADC with up to 9 channels and 1.1 Msps conversion rate, three 16-bit timers, a UART, an SPI, and an I2C port. The 28-QFN (6x6 mm) package offers a compact footprint with a thermal pad for board-level heat spreading and operates across -40C to +85C industrial temperature range from a 3.0 V to 3.6 V single supply. The architecture features separate program and data memory spaces and buses, a 24-bit instruction word with 16-bit data paths, and a barrel shifter that supports single-cycle shifts. Its dual 40-bit accumulators with configurable saturation logic prevent overflow during control-loop math, while the MCU-class interrupt controller and peripheral set allow the device to replace multi-chip MCU + DSP solutions in sensorless BLDC, PMSM, and brushed-DC drive stages. Typical applications include low-voltage sensorless BLDC and PMSM motor control, HVAC blowers and pumps, appliance fan drives, RC-servo and drone ESC controllers, small UPS and inverter auxiliary control loops, and industrial stepper drives. The 12 KB Flash budget suits tight assembly-level state machines and look-up tables for sinusoidal commutation. The QFN-28 footprint also enables use as a digital control companion to analog gate drivers in compact half-bridge designs. When designing with this device, allocate the QFN thermal pad with a continuous copper pour and at least 9 thermal vias to the internal ground plane to keep junction temperature within limits under heavy PWM switching loads. Always enable the watchdog timer and configure the motor-control PWM fault inputs to immediately tri-state outputs in hardware, bypassing firmware latency for safe commutation on overcurrent events. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the dsPIC33F family, and practical design notes not found on a single manufacturer datasheet page.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202-I/SO

DSPIC33FJ12MC202-I/SO - 16-bit DSC, 12KB Flash, 40 MIPS Motor Control MCU | Microchip

The Microchip DSPIC33FJ12MC202-I/SO is a 16-bit Digital Signal Controller (DSC) in a 28-pin SOIC (7.50 mm) wide-body package that delivers 40 MIPS throughput, 12 KB Flash program memory, and 1 KB SRAM from a 3.0 V to 3.6 V single supply. It pairs a 16-bit MCU architecture with on-chip DSP extensions (MAC, barrel shifter, hardware divide) and motor-control oriented peripherals including a 6-channel PWM with complementary outputs and programmable dead time, a 200 ksps 10-bit ADC, and a 16-bit timer/capture/compare cluster. The '-I' suffix indicates the industrial operating range of -40 °C to +85 °C, and the '/SO' suffix denotes the wide-body 300-mil SOIC-28 footprint. What is a Digital Signal Controller (DSC)? A DSC is a hybrid MCU/DSP family that retains the deterministic interrupt model of a microcontroller while adding single-cycle MAC and saturating arithmetic, allowing closed-loop control loops and audio/power signal processing to run on a single device instead of an MCU+DSP pair. The dsPIC33FJ12MC202 sits inside Microchip's motor-control subgroup of the dsPIC33F family; in the wider taxonomy it belongs to MCU -> 16-bit MCU -> DSC -> motor-control DSC -> power management & motion control semiconductor. Key features include 40 MHz operation (10 MIPS at 3.3 V), 21 general-purpose I/O with 5 V-tolerant inputs, JTAG/ICSP debug, two UART, one SPI, one I2C, a 6-channel motor-control PWM, a 200 ksps 10-bit ADC (up to 9 channels on this 28-pin variant), and peripheral pin select for flexible signal routing. The 28-pin SOIC footprint is pin-compatible with the PIC24 and dsPIC33F GP202 families, easing PCB reuse across control SKUs. Architecturally, the device uses a Harvard bus with separate program (Flash) and data (SRAM) paths, a 16 × 16-bit working register array, and DSP instructions that execute in a single oscillator cycle. The internal 7.3728 MHz FRC oscillator with 64x PLL provides 40 MIPS at ±1 % accuracy over voltage and temperature, allowing the MCU to run without an external crystal and still meet Class-B motor-control timing. Typical applications include brushed DC motor drives, BLDC/PMSM sensored and sensor-less control, low-powerfield-oriented-control (FOC) fans and pumps,small appliance drives, and digital lighting ballasts. The 40 MIPS headroom + dedicated PWM/ADC hardware pair is sized for 6-step trapezoidal commutation up to ~30 kHz electrical frequency. When designing with this device, populate the MCLR pull-up, place AVSS/AGND and VSS/VSS separation on a star ground, and use the peripheral pin-select feature if your PCB swaps UART lines for SPI debug access. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202-I/SS

DSPIC33FJ12MC202-I/SS - 40 MIPS 16-bit Motor Control DSC | Microchip

The Microchip Technology DSPIC33FJ12MC202-I/SS is a 16-bit Digital Signal Controller (DSC) engineered for high-performance motor control applications, integrating DSP and MCU functionality on a single die. The device delivers 40 MIPS throughput from a 40 MHz CPU at 3.0-3.6V, includes 12 KB of Flash program memory and 1 KB of RAM, and operates over the industrial -40C to +85C temperature range in a 28-pin SSOP package. A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller's deterministic control peripherals with a digital signal processor's math engine, enabling closed-loop control loops, power-factor correction, and sensorless motor algorithms in a single chip. The dsPIC33F family adds a 16-bit data path with a hardware multiplier and barrel shifter, allowing designers to execute field-oriented control (FOC), space-vector modulation, and digital filtering without offloading to a separate DSP. Key features of the DSPIC33FJ12MC202 include dedicated motor-control peripherals: a 6-channel PWM module with complementary or independent output modes and programmable dead time, a 1.5 Msps 10-bit ADC with up to 8 analog channels, and a 16-bit quadrature encoder interface for position feedback. The part also provides I2C, SPI, and UART/USART connectivity, plus IrDA support, and 21 general-purpose I/O pins. At the silicon level, the device uses separate program and data memory buses (Harvard architecture) so that instruction fetches and data accesses occur in parallel. This eliminates the wait-state penalties common to von Neumann MCUs and is the structural reason dsPIC33F parts can sustain 40 MIPS while executing multiply-accumulate (MAC) operations every instruction cycle. Typical applications include BLDC and PMSM motor drives, sensorless fan and pump controllers, small appliance motor drives, and HVAC damper actuators. The 28-pin SSOP footprint also suits LED lighting drivers and DC-DC converter digital control loops where tight PWM timing is required. When designing with this part, allocate ADC sampling within the PWM cycle to avoid converter noise injection and use the dedicated QEI pins for encoder feedback rather than remapping general-purpose I/O. Brown-out reset and the on-chip LVD ensure deterministic startup under variable supply rails. This page synthesizes distributor pricing, parametric alternatives, and practical design notes not found in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202T-E/ML

DSPIC33FJ12MC202T-E/ML - 16-bit Motor Control DSC, 12KB Flash | Microchip

The Microchip DSPIC33FJ12MC202T-E/ML is a 16-bit Digital Signal Controller (DSC) that combines DSP performance with a 16-bit MCU architecture, optimized for motor control applications. Housed in a 28-pin QFN (6x6 mm) package with extended automotive temperature grade (-40C to +125C), it integrates 12KB of Flash program memory, 1024 bytes of SRAM, and 1024 bytes of EEPROM, while supporting operation from 3.0V to 3.6V. The DSC core runs up to 40 MIPS at 3.3V and includes a single-cycle 16x16-bit MAC, dual 40-bit accumulators, and a barrel shifter, enabling precise field-oriented control (FOC) loops. A Digital Signal Controller (DSC) is a hybrid device that merges a microcontroller's deterministic control peripherals with a digital signal processor's arithmetic throughput. Within the broader product hierarchy, the dsPIC33F sits between general-purpose PIC24 MCUs and high-end dsPIC33E DSCs, targeting real-time control loops that demand both fixed-point DSP and deterministic interrupt response - the same hierarchy as DSP > microcontroller > semiconductor. This positions the part above a standard PIC16/PIC18 MCU but below application processors, ideal for sensored and sensorless motor control. Key features include a 6-channel PWM module with complementary outputs and dead-time control, a 10-bit ADC with up to 9 channels and 1.1 Msps conversion rate, three 16-bit timers, and Peripheral Pin Select (PPS) for flexible signal routing. The Motor Control PWM supports edge-aligned, center-aligned, and variable-phase modes, allowing direct driving of three-phase inverter bridges. The nanoWatt power management unit offers Idle, Sleep, and DOZE modes that reduce quiescent current during standby, extending battery life in portable drives. The dsPIC33FJ12MC202 architecture separates program and data memory buses (Harvard) with 24-bit instruction words, allowing simultaneous fetch of opcode and data. The interrupt controller supports up to five priority levels and 65 vectored interrupts, while the JTAG and ICSP interfaces enable in-circuit debug and device programming without external hardware. The QFN-28 package exposes a thermal pad to minimize junction-to-PCB thermal resistance, supporting continuous switching currents typical of 24V brushless DC motor drives. Typical applications include sensorless BLDC/PMSM motor drives, low-voltage fan and pump controllers, small appliance inverters, e-bike controllers, and automotive auxiliary motor drives. The 12KB Flash is sufficient for field-oriented control algorithms with sinusoidal commutation tables, while 1KB SRAM accommodates state observers without external memory expansion. Designers should note that the -E temperature grade qualifies the part for automotive under-hood environments.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202T-E/SO

DSPIC33FJ12MC202T-E/SO - 16-bit DSC, 12KB Flash, 28-SOIC | Microchip

The Microchip DSPIC33FJ12MC202T-E/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering 40 MIPS performance with 12KB Flash and 1024 bytes of SRAM in a 28-pin SOIC package. The "E" suffix denotes the extended (-40C to +125C) automotive temperature grade, and the "T" suffix indicates Tape & Reel packaging for high-volume assembly. Targeted at motor control and digital power conversion, the device integrates a DSP engine with a high-performance microcontroller architecture optimized for closed-loop control loops. What is a Digital Signal Controller? A Digital Signal Controller (DSC) is a hybrid device that combines the deterministic interrupt response of a microcontroller (MCU) with the computational throughput of a Digital Signal Processor (DSP). The DSC taxonomy flows as: microcontroller < digital signal controller < dsPIC33F family < 16-bit MCU < semiconductor. DSCs are widely used in applications that require single-cycle MAC (multiply-accumulate) operations, hardware PWMs, and fast ADC sampling - exactly what motor control, power conversion, and switch-mode power supplies demand. Key features include a 16-bit data path with single-cycle 40 MIPS throughput, an integrated Motor Control PWM module with up to 6 PWM outputs, a 10-bit ADC capable of up to 1.1 Msps, and the nanoWatt power management suite for sleep currents down to the microamp range. The device is qualified to AEC-Q100 standards, making it suitable for under-hood automotive motor control systems including HVAC blowers, fuel pumps, water pumps, and seat-position actuators. The architecture combines a modified Harvard bus with a single-cycle MAC unit that executes 40 million DSP operations per second, paired with dual-port SRAM and tightly-coupled peripherals. The 28-SOIC footprint exposes three PWM channels, an I2C/SPI/UART set, and a 6-channel 10-bit ADC, allowing designers to build compact BLDC, PMSM, or sensored/stepper motor inverters. Typical applications include brushless DC (BLDC) motor drives, permanent-magnet synchronous motor (PMSM) sensorless control, switched-mode power supplies (SMPS) and uninterruptible power supplies (UPS), HVAC fan control, and small appliance motor inverters. The AEC-Q100 qualification, extended temperature grade, and rich PWM peripheral set make it especially attractive for automotive body electronics and white-goods variable-frequency drives. When designing with the DSPIC33FJ12MC202T-E/SO, ensure the PWM fault input and current-sense ADC channels are prioritized in firmware; the PWM module can trigger the ADC for sub-microsecond current-loop sampling. Use the device's nanoWatt sleep mode to drop quiescent current to a few microamps between motor commands. This page synthesizes distributor pricing, AEC-Q100 qualified drops-in alternatives, and hands-on motor-control design notes not bundled in the manufacturer datasheet, giving engineers a faster path to a production-ready BLDC or PMSM design.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202T-I/ML

DSPIC33FJ12MC202T-I/ML - 16-bit Motor Control DSC, 40MHz, 28-QFN | Microchip

The Microchip Technology DSPIC33FJ12MC202T-I/ML is a 16-bit Digital Signal Controller (DSC) engineered for high-performance, variable-speed motor control applications. Built around the dsPIC33F CPU core, it executes instructions at up to 40 MIPS (40 MHz), combines a hardware multiply-accumulate (MAC) engine, a 40-bit barrel shifter, and a single-cycle 16x16-bit multiplier for deterministic DSP throughput in Field-Oriented Control (FOC) loops. The part integrates 12 KB of Flash program memory, 1 KB of general-purpose SRAM, and is offered here in the 28-lead 6 x 6 mm QFN package with operating temperature range -40 C to +85 C, supplied across a 3.0 V to 3.6 V range. A Digital Signal Controller (DSC) is a hybrid device that fuses the deterministic real-time peripheral set of a microcontroller with the parallel arithmetic paths of a digital signal processor, enabling single-chip implementation of closed-loop motor-control firmware. It sits within a broader hierarchy of motor-control silicon: DSC -> microcontroller -> embedded processor -> semiconductor. The dsPIC33F family targets cost-sensitive motor drive, switching power supply, and inverter applications where 32-bit DSP performance is not essential but bare-metal 16-bit DSP throughput is mandatory. Key features of this 202 variant include one dedicated 6-channel PWM module optimized for 3-phase inverters (complementary outputs with adjustable dead time, hardware fault input), a 10-bit ADC with up to 9 channels and 1.1 Msps throughput, two comparators with programmable references, and the nanoWatt power-management suite offering Idle, Sleep, and Doze modes that drop quiescent current into the microamp range for standby compliance. The architecture's distinguishing trait is hardware DSP assist in a 16-bit MCU price envelope. The 24-bit instruction word, dual 40-bit accumulators, and zero-overhead DO and REPEAT loops let CLOSED-loop control cycles (current loop, speed loop, sensorless observers) fit inside a single PWM period without CPU loading, reducing BOM cost by eliminating an external DSP or FPGA in compact drives such as ceiling fans, pump controllers, and appliance BLDC modules. Typical applications span 3-phase BLDC and PMSM motors in white goods, HVAC blowers, RC hobby ESCs, low-voltage traction controllers, ceiling-fan drivers, small appliance pumps, and Uninterruptible Power Supply (UPS) inverter stages where the single-chip DSC collapses the bill of materials versus two-piece MCU+DSP solutions. The 28-pin QFN gives an extremely compact footprint for space-constrained boards. A first-pass design tip: the PWMin/Comparator/OC fault inputs must be brought out to dedicated PCB traces routed directly from the gate-driver or current-sense network, and the exposed pad must be soldered to a continuous ground pour. Reference the dsPIC33FJ12MC201/202 datasheet for pinout maps and the dsPICDEM MC1 motor-control development board for a vetted peripheral-assignment pattern. This page consolidates distributor pricing, drop-in alternatives drawn from the same Microchip dsPIC33F MC family, and practical hardware design notes not always summarized in the official datasheet.

طلب عرض سعر اتصل بنا

DSPIC33FJ12MC202T-I/SS

DSPIC33FJ12MC202T-I/SS - 16-Bit 40MIPS Motor Control DSC | Microchip

The Microchip Technology DSPIC33FJ12MC202T-I/SS is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, combining DSP engine throughput with microcontroller peripherals for high-performance motor control. It delivers 40 MIPS at 40 MHz with 12 KB of Flash program memory, 1 KB of SRAM, and 21 general-purpose I/O pins, packaged in a 28-pin SSOP (5.30 mm body width). The integrated DSP engine executes MAC operations in a single cycle, enabling field-oriented control (FOC) loops, sensorless algorithms, and high-bandwidth current regulation. A Digital Signal Controller (DSC) is a hybrid architecture that fuses a deterministic MCU core with the math density of a DSP. In the broader taxonomy, this part is a motor-control-optimized DSC -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. It fits between pure MCUs (which lack DSP throughput for tight control loops) and full DSPs (which lack general-purpose peripherals for sequencing). The dsPIC33FJ12MC202 places DSP acceleration in front of the MCU bus so that interrupt-driven motor loops can close in microseconds without CPU starvation. Key features of the DSPIC33FJ12MC202T-I/SS include a 6-channel 10-bit/12-bit ADC with up to 1.1 Msps conversion rate, dedicated motor-control PWM with complementary outputs and programmable dead time, a quadrature encoder interface (QEI) for position feedback, and on-chip Flash with self-programming support. The -40C to +85C industrial temperature grade and 3.0 V to 3.6 V supply range suit industrial drives, appliance compressors, and HVAC blowers. Typical applications include BLDC and PMSM motor drives for fans and pumps, sensorless FOC compressors, low-power field-oriented servo drives, ceiling-fan and small-appliance inverter stages, and battery-powered e-mobility controllers where deterministic loop time and DSP MAC throughput minimize torque ripple. Designers should plan for the dedicated motor-control PWM alignment to gate-driver propagation delays and use the QEI peripheral for rotor-position feedback. The 28-SSOP footprint keeps the BOM cost lower than QFN alternatives while still exposing the full motor-control peripheral set. This page synthesizes distributor pricing, drop-in SSOP-28 alternatives, and practical design notes not consolidated in the manufacturer datasheet.

طلب عرض سعر اتصل بنا

DSPIC33FJ16GP101-E/SO

DSPIC33FJ16GP101-E/SO - 16 MIPS 16KB Flash DSC, SOIC-18

The Microchip DSPIC33FJ16GP101-E/SO is a 16-bit, 16-MIPS digital signal controller (DSC) built on the dsPIC33F RISC core, integrating 16 KB of Flash program memory and 1 KB of RAM into an 18-pin SOIC W (wide-body) package. Rated for an extended industrial temperature range of -40 °C to +125 °C and supplied from 3.0 V to 3.6 V, the part delivers deterministic signal-processing throughput for closed-loop digital control. In the broader device taxonomy, the DSPIC33FJ16GP101 belongs to the dsPIC33F "GP" (General Purpose) family of Digital Signal Controllers, an intermediate class between traditional 8/16-bit microcontrollers and full Digital Signal Processors (DSPs). DSPs add hardware multiply-accumulate (MAC) units, dual-ported SRAM, and zero-overhead looping to a microcontroller's peripheral set, enabling single-cycle 16x16 MAC operations and on-chip FIR/IIR filter execution without taxing the CPU. The GP sub-family is engineered for general-purpose DSP and high-speed precision digital control, making it useful wherever a closed-loop algorithm must run in real time without an external DSP. Key features include a 40 MHz maximum operating frequency (16 MIPS at FCY = FOSC/2), an enhanced ADC with up to 12-bit resolution and on-chip reference, a motor-control PWM peripheral, I2C, SPI, and UART interfaces, five 16-bit timer/counters, and three external interrupts with two remappable sources. The 5V-tolerant I/Os source/sink 10 mA or 6 mA in standard mode and up to 20 mA in non-standard VOH1 mode, easing direct drive of logic-level circuitry. Typical applications include industrial motor control (BLDC, PMSM, and stepper drives), digital power conversion, sensorless fan and pump controllers, audio processing front-ends, and precision switch-mode power supplies. Automotive-grade (-E) screening and the SOIC-18 footprint also suit AEC-Q100 contexts and through-hole-friendly prototyping. When designing with this part, plan for an external 2.5-3.0 V LDO and a low-ESR decoupling network on VDDCORE. Use ICSP for programming and the device's remappable peripheral pins (RPn) to optimize PCB routing on the small SOIC-18 footprint. This page synthesizes distributor stock, design-in considerations and drop-in alternatives that complement the Microchip datasheet (DS-70000652F).

طلب عرض سعر اتصل بنا

الفئات الفرعية

المنتجات (39,000+)

DSPIC33FJ12GP202-I/ML - 16-bit DSC, 40 MIPS, 28-QFN | Microchip

DSPIC33FJ12GP202-I/SO - 16-bit DSC, 40MIPS, 28-SOIC | Microchip

DSPIC33FJ12GP202-I/SP - 16-Bit DSC, 40 MIPS, 12KB Flash | Microchip

DSPIC33FJ12GP202-I/SS - 16-bit DSC, 12KB Flash, 40 MIPS | Microchip

DSPIC33FJ12GP202T-I/ML - 16-bit DSC, 40 MIPS, 12KB Flash | Microchip

DSPIC33FJ12GP202T-I/SO - 40 MIPS 16-bit DSC, 12KB Flash, 28-SOIC

DSPIC33FJ12MC201-E/P - 16-bit Motor Control DSC, 12KB Flash | Microchip

DSPIC33FJ12MC201-E/SO - 16-bit Motor Control DSC, 40MHz, 20-SOIC | Microchip

DSPIC33FJ12MC201-E/SS - 16-bit Motor Control DSC, 40MHz, SSOP-28 | Microchip

DSPIC33FJ12MC201-I/SO - 16-bit Motor Control DSC, 40 MIPS | Microchip

DSPIC33FJ12MC201-I/SS - 16-bit DSC, 40MHz, 12KB Flash | Microchip

DSPIC33FJ12MC201T-I/SO - 16-bit 40MIPS 12KB Flash Motor Control DSC | Microchip

DSPIC33FJ12MC201T-I/SS - 40 MIPS Motor Control DSC | Microchip

DSPIC33FJ12MC202-E/ML - 16-Bit Motor Control DSC, 40 MIPS, 28-QFN | Microchip

DSPIC33FJ12MC202-E/SO - 16-bit Motor Control DSC, 12KB Flash | Microchip

DSPIC33FJ12MC202-E/SS - 16-bit Motor Control DSC, 40 MIPS, 12KB Flash | Microchip

DSPIC33FJ12MC202-I/ML - 16-bit DSC, 12KB Flash, 40 MIPS Motor Control

DSPIC33FJ12MC202-I/SO - 16-bit DSC, 12KB Flash, 40 MIPS Motor Control MCU | Microchip

DSPIC33FJ12MC202-I/SS - 40 MIPS 16-bit Motor Control DSC | Microchip

DSPIC33FJ12MC202T-E/ML - 16-bit Motor Control DSC, 12KB Flash | Microchip

DSPIC33FJ12MC202T-E/SO - 16-bit DSC, 12KB Flash, 28-SOIC | Microchip

DSPIC33FJ12MC202T-I/ML - 16-bit Motor Control DSC, 40MHz, 28-QFN | Microchip

DSPIC33FJ12MC202T-I/SS - 16-Bit 40MIPS Motor Control DSC | Microchip

DSPIC33FJ16GP101-E/SO - 16 MIPS 16KB Flash DSC, SOIC-18