উপশ্রেণী

পণ্য (44,000+)

XMC4504-F144F512AB - 120MHz Cortex-M4 MCU | Infineon
XMC4504-F144F512AB

XMC4504-F144F512AB - 120MHz Cortex-M4 MCU | Infineon

The Infineon XMC4504-F144F512AB is a 32-bit ARM Cortex-M4 industrial microcontroller operating at 120 MHz, with 512 KB of flash memory and a 144-pin PG-LQFP-24 package. It belongs to the XMC4000 family and is designed for industrial applications requiring deterministic real-time control, connected peripherals, and a broad set of analog and digital interfaces. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and communication interfaces on one semiconductor device. In the hierarchy of electronic components, this MCU sits below embedded processor and below the broader category of semiconductors, while it is above general-purpose control logic in system-level terminology. The ARM Cortex-M4 core provides a 32-bit processing environment suitable for motor control, industrial automation, communications, and embedded measurement systems. The verified data identifies the XMC4504-F144F512AB as an XMC4000-series device with 120 MHz operation, 512 KB flash, an Ethernet MAC, 32-bit architecture, and a 144-pin LQFP package. The related Infineon XMC4504-F144K512-AC product page identifies the same 120 MHz, 512 kB, Ethernet MAC platform for industrial applications, providing useful family-level context while the exact orderable MPN remains the requested AB variant. The part is especially relevant when a design needs substantial embedded processing alongside Ethernet connectivity. The 120 MHz core can support protocol handling, supervisory control, signal processing, and real-time control tasks, while the 512 KB flash capacity provides a practical balance between firmware storage and system integration. The LQFP-144 package exposes a broad pin count for external peripherals and mixed-signal interfaces. Typical uses include industrial Ethernet equipment, factory automation controllers, building and infrastructure electronics, communication gateways, and embedded control platforms. Engineers should verify the exact peripheral assignments, electrical limits, pin multiplexing, startup configuration, memory map, and package details against the manufacturer documentation before layout or firmware deployment. The principal design consideration is package and software verification rather than headline performance. Confirm that the PCB land pattern matches the exact 144-pin LQFP variant, that all required power, clock, reset, debug, and communication signals are available, and that the selected toolchain supports the XMC4000 family. This page consolidates the verified source information, source links, application context, and engineering caveats without inventing unavailable electrical details.

RFQ যোগাযোগ
XMC4504F100K512ACXQMA1 - Cortex-M4 120MHz MCU | Infineon
XMC4504F100K512ACXQMA1

XMC4504F100K512ACXQMA1 - Cortex-M4 120MHz MCU | Infineon

Infineon Technologies XMC4504F100K512ACXQMA1 is an industrial 32-bit microcontroller built around an Arm Cortex-M4 processor core operating at 120 MHz. It provides 512 KB of flash memory, 128 KB of SRAM, and an Ethernet MAC in a 100-pin LQFP package with an exposed pad. The device is intended for embedded industrial systems requiring deterministic real-time control, Ethernet connectivity, and a substantial local memory configuration. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. Within the embedded-control hierarchy, the Cortex-M4 core belongs to the Arm Cortex-M family of 32-bit RISC processors. The XMC4000 family combines that core with industrial-oriented peripherals, flash, SRAM, communications interfaces, and clock-management resources, making the XMC4504 suitable for control systems that need both computation and network connectivity. The main architectural features are a 120 MHz operating frequency, 512 KB of flash, 128 KB of SRAM, and integrated Ethernet MAC functionality. Flash supports code storage and firmware updates, while SRAM provides working memory for protocol stacks, control state, diagnostics, and real-time tasks. The Ethernet MAC allows the controller to participate in a network without requiring a separate MAC block elsewhere in the system. Infineon identifies the device as part of its industrial XMC4000 microcontroller family. The XMC4504-F100F512-AC ordering designation identifies a 120 MHz Cortex-M4 industrial microcontroller with 512 KB of flash and 128 KB of SRAM. This part is supplied in a PG-LQFP-100 package with an exposed pad and is offered in tray packaging according to the product listing. The exposed thermal pad provides a direct heat-transfer path into the PCB, while the large 100-pin package exposes the device's broader pin and peripheral configuration. Typical applications include industrial Ethernet controllers, programmable automation equipment, connected sensor-hub systems, industrial gateways, motion-control equipment, and embedded data-acquisition platforms. In each case, the 512 KB flash capacity can hold application firmware and protocol components, while the 128 KB SRAM can support networking buffers and real-time control state. An external Ethernet PHY is still required for the physical network interface when the MCU supplies only the Ethernet MAC. PCB design should prioritize clean supply decoupling, a solid thermal-pad connection, and controlled routing of high-speed Ethernet signals. Place the input and bypass capacitors close to their associated supply pins, connect the exposed pad to the appropriate ground plane, and follow the package and layout guidance in the Infineon datasheet. Validate the complete clock, PHY, magnetics, and signal-integrity implementation before production release. This page consolidates the manufacturer specifications, memory and connectivity requirements, package characteristics, application guidance, and replacement considerations into a practical engineering reference. It also distinguishes confirmed ordering information from areas that require device-specific validation before schematic release or firmware deployment.

RFQ যোগাযোগ
XMC4504F144F512ABXQMA1 - 120MHz Cortex-M4 MCU | Infineon
XMC4504F144F512ABXQMA1

XMC4504F144F512ABXQMA1 - 120MHz Cortex-M4 MCU | Infineon

Infineon Technologies XMC4504F144F512ABXQMA1 is a 32-bit ARM Cortex-M4 XMC4000 series microcontroller with a maximum clock frequency of 120 MHz, 512 KB of flash memory, and a PG-LQFP-144-18 package. It is designed for embedded applications requiring real-time control, industrial connectivity, and deterministic peripheral integration. The device combines a 32-bit Cortex-M4 processor with 512 kB of program memory and an Ethernet MAC, making it suitable for industrial networking, automation equipment, communication controllers, and connected embedded systems. A microcontroller is a compact integrated circuit containing a processor core, program memory, data memory, peripherals, and communication interfaces. The XMC4000 family combines an ARM Cortex-M4 core with Infineon automotive and industrial embedded-control capabilities. This MCU is positioned for applications that need more processing performance and connectivity than a small 8-bit or 16-bit controller, while retaining a broad set of timers, serial interfaces, analog functions, and communication peripherals for system integration. The XMC4504F144F512ABXQMA1 operates at up to 120 MHz and includes 512 KB of flash memory. Its 32-bit architecture supports efficient control-loop execution, protocol handling, and signal-processing tasks. The Ethernet MAC provides a practical foundation for industrial Ethernet designs, while the extensive peripheral set can reduce the number of external components needed for sensor acquisition, actuator control, communications, and system monitoring. The PG-LQFP-144-18 package provides a high pin count for parallel I/O, analog functions, and multiple communication channels. Typical applications include industrial Ethernet equipment, factory automation controllers, building automation gateways, motor and power-control systems, communications infrastructure, and connected industrial sensors. The Cortex-M4 processing capability is useful for protocol stacks, state machines, data acquisition, and supervisory control. For designs requiring deterministic timing, the MCU can combine its high-frequency core with dedicated timer resources and event-driven peripherals instead of relying on a general-purpose host processor. Designers should verify the complete pin assignment, peripheral multiplexing, clock configuration, memory map, and electrical limits in the manufacturer datasheet before laying out the PCB. The LQFP package also requires attention to thermal dissipation, especially when the core and communication peripherals operate continuously. Power sequencing, decoupling, debug access, and Ethernet interface implementation should be planned early because these functions can materially affect board-level reliability and compliance. This product page summarizes the verified XMC4504F144F512ABXQMA1 identity and combines its principal MCU specifications with application guidance, comparison information, and practical design considerations. It is intended to help engineers identify the correct Infineon part, assess its 120 MHz Cortex-M4 and 512 KB flash configuration, and determine whether the XMC4504 platform is suitable for an industrial embedded-control design.

RFQ যোগাযোগ
XMC4504F144F512ACXQMA1 - 120MHz Cortex-M4 MCU | Infineon
XMC4504F144F512ACXQMA1

XMC4504F144F512ACXQMA1 - 120MHz Cortex-M4 MCU | Infineon

The Infineon XMC4504F144F512ACXQMA1 is a 32-bit Arm Cortex-M4 microcontroller in the XMC4000 family, operating at 120 MHz with 512 KB of flash memory in a PG-LQFP-144-10 package. It combines an industrial microcontroller core with Ethernet connectivity and is identified as a 1.3 V or 3.3 V device for embedded control and connected industrial equipment. An XMC4000-series microcontroller combines an Arm Cortex-M4 processor with industrial-oriented peripherals in a single system-on-chip. The Cortex-M4 architecture supports efficient interrupt-driven control, while the XMC4000 family is designed for automation, communications, and embedded networking systems that need deterministic real-time behavior alongside an Ethernet interface. This device therefore belongs to the industrial microcontroller hierarchy rather than the general-purpose consumer MCU category. Principal characteristics include a 120 MHz CPU frequency, 512 KB of program flash, 32-bit processing, and an Ethernet MAC. The PG-LQFP-144-10 surface-mount package exposes 144 pins and is offered in a tray configuration. According to the Infineon product summary, the XMC4504-F144F512-AC industrial variant is designed around an operating voltage of 1.3 V to 3.63 V, making it suitable for low-voltage industrial boards designed around either 1.8 V or 3.3 V interfacing. The 512 KB flash allocation provides room for a substantial bootloader, network stack, field-service routines, and application firmware within a single device. Ethernet support allows the controller to participate directly in industrial Ethernet networks without an external interface controller. Exact RAM capacity, peripheral mix, temperature limits, and Ethernet physical-layer requirements should be confirmed in the manufacturer datasheet before the part is committed to a new board. Typical uses include industrial Ethernet gateways, programmable automation controllers, building automation equipment, motor and motion-control modules, and connected sensor-hub designs. Its 120 MHz processing headroom supports protocol handling alongside real-time control tasks, while the 144-pin LQFP package simplifies assembly for prototypes and moderate-production industrial boards compared with very fine-pitch BGA packages. For PCB design, follow the Infineon reference layout, power-supply decoupling, and exposed pad or thermal-via guidance in the manufacturer datasheet. Validate the Ethernet PHY or magnetics arrangement, maintain defined supply sequencing, and confirm that the selected 1.3 V or 3.3 V operating point matches the internal core and I/O requirements of the complete design. This page consolidates the verified manufacturer specifications, ordering information, package details, and practical engineering guidance for the XMC4504F144F512ACXQMA1. It also identifies a same-family ordering option and documents which parameters must still be confirmed against the manufacturer datasheet during hardware design review.

RFQ যোগাযোগ
XMC4504F144K512ACXQMA1 - 120MHz Cortex-M4 512KB MCU | Infineon
XMC4504F144K512ACXQMA1

XMC4504F144K512ACXQMA1 - 120MHz Cortex-M4 512KB MCU | Infineon

Infineon Technologies XMC4504F144K512ACXQMA1 is a 32-bit industrial Arm Cortex-M4 microcontroller operating at up to 120 MHz, with 512 KB of embedded flash memory and an Ethernet MAC, housed in a PG-LQFP-144-18 package. The device combines a 120 MHz Arm Cortex-M4 processor core with configurable industrial peripherals for energy-efficient embedded control and communications designs. An Arm Cortex-M4 microcontroller is a 32-bit reduced-instruction-set processor designed for embedded control. It belongs to the Arm Cortex-M family and provides integrated flash memory, SRAM, communication peripherals, timers, and interrupt-control hardware in one device. The XMC4504F144K512ACXQMA1 extends this architecture into the Infineon XMC4500 family for industrial applications that require real-time control and Ethernet connectivity. The principal device characteristics include a 120 MHz maximum clock, 512 KB of flash, 128 KB of SRAM, and a single processor core. Its 1.3 V and 3.3 V supply descriptions correspond to embedded core and I/O operating domains. The 144-lead PG-LQFP package provides ample I/O capacity for external memory interfaces, communications, analog inputs, timers, and industrial control signals while supporting surface-mount assembly. The XMC4500 architecture integrates Ethernet MAC functionality with a configurable peripheral set, allowing designers to tailor the controller to specific application requirements. Peripheral functionality and pin multiplexing should be configured together because the available pins and alternate functions depend on the selected operating mode. Firmware development uses the Arm Cortex-M4 programming model, with startup, linker, and device-support files required for the specific Infineon part and package. Typical applications include industrial Ethernet controllers, factory automation equipment, networked sensors, industrial gateways, motor-control systems, and embedded automation platforms. The combination of 120 MHz processing performance, 512 KB flash, and Ethernet MAC support makes the device appropriate for control nodes that must execute application firmware while communicating over an industrial Ethernet network. When assigning the package pins, consult the manufacturer pin-description table for the exact PG-LQFP-144-18 pinout. In particular, verify the functions of communication, debug, analog, reset, clock, and power pins before finalizing PCB routing. Proper decoupling, exposed-pad thermal design, and signal-integrity practices remain essential for reliable industrial operation. This page combines the manufacturer product identity, distributor specification details, same-family drop-in candidates, application guidance, and design-focused comparisons. These engineering references help engineers assess package reuse, peripheral compatibility, firmware prerequisites, and sourcing requirements before committing the XMC4504F144K512ACXQMA1 to an industrial embedded design.

RFQ যোগাযোগ
XMC4700E196K2048AAXQMA1 144MHz 2MB MCU | Infineon
XMC4700E196K2048AAXQMA1

XMC4700E196K2048AAXQMA1 144MHz 2MB MCU | Infineon

Infineon XMC4700E196K2048AAXQMA1 is a 32-bit ARM Cortex-M4 industrial microcontroller operating at up to 144 MHz, with 2 MB of embedded Flash, 352 kB of SRAM, and Ethernet connectivity in a 196-pin PG-LFBGA-196-2 package. The device is designed for industrial control and communication systems requiring substantial processing performance, embedded memory, and a high pin count. A microcontroller is a programmable system-on-chip that combines a processor core, memory, peripherals, and communication interfaces. Within the embedded-control hierarchy, this XMC4700 belongs to the XMC4000 family of ARM Cortex-M4 microcontrollers, which sits between general-purpose embedded processors and highly integrated industrial controllers. The ARM Cortex-M4 core provides 32-bit processing suitable for deterministic control loops, communications management, and protocol handling. The XMC4700E196K2048AAXQMA1 provides 2048 kB of Flash for program storage and 352 kB of SRAM for working data. Its maximum operating frequency of 144 MHz supports computationally intensive industrial tasks, while the 196-pin package provides access to a broad peripheral and signal interface set. The product family supports Ethernet and CAN communication, making it applicable to connected automation equipment. EtherCAT slave support is identified for the XMC4700 family, providing a dedicated path for industrial Ethernet motion-control applications. The combination of EtherCAT capability, Ethernet, CAN, high-speed processing, and embedded memory distinguishes this device from general-purpose microcontrollers with narrower real-time communication requirements. Typical uses include industrial automation controllers, servo and motor-control platforms, networked industrial equipment, programmable logic controllers, and communications gateways. The 196-pin LFBGA package supports dense mixed-signal and digital designs but requires a carefully designed multilayer PCB, appropriate escape routing, and controlled assembly processing. Designers should follow the manufacturer’s package, pin-multiplexing, power, decoupling, and PCB-layout guidance in the XMC4700 documentation. Firmware must also account for the selected peripheral assignments, clock configuration, memory organization, and communication-stack requirements before the device is placed into production. This page consolidates the exact orderable MPN, principal memory and processor specifications, package details, communication capabilities, practical application guidance, and verified sourcing links. It also records the absence of a verified pin-by-pin assignment and qualifying drop-in alternatives rather than presenting unconfirmed substitution data as drop-in compatibility.

RFQ যোগাযোগ
XMC4700F100K1536AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon
XMC4700F100K1536AAXQMA1

XMC4700F100K1536AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon

The Infineon Technologies XMC4700F100K1536AAXQMA1 is a 32-bit ARM Cortex-M4 microcontroller in the XMC4000 family, operating up to 144 MHz with 1.5 MB of embedded flash, 276 kB of SRAM, and integrated Ethernet connectivity. It is supplied in a 100-pin PG-LQFP package for industrial embedded-control designs. A microcontroller is a programmable semiconductor integrating a processor core, memory, peripherals, and communication interfaces on one device. The XMC4000 family belongs to the industrial embedded-control hierarchy, combining real-time processing with DSP and floating-point capabilities. This makes the XMC4700 suitable when a design requires deterministic control, network communication, mixed-signal acquisition, timer and PWM control, or a combination of these functions. Principal device characteristics include an ARM Cortex-M4 processor core, 32-bit architecture, 144 MHz maximum operating frequency, 1.536 MB of flash memory, and 276 kB of SRAM. The ordering designation identifies an industrial-grade XMC4700 configuration in a 100-pin LQFP package. Integrated Ethernet allows the controller to participate directly in connected industrial equipment without requiring a separate network interface. The XMC4700 architecture supports embedded control workloads requiring both real-time peripheral handling and higher-level protocol processing. Its substantial flash capacity allows larger control firmware, communication stacks, and application logic to be consolidated into one component, while SRAM supports active control loops, packet buffers, and working memory. The 144 MHz Cortex-M4 core includes DSP-oriented instruction support and FPU capability according to the family description. Typical applications include industrial Ethernet controllers, motor and power-conversion control, factory automation equipment, industrial networking gateways, and connected embedded-control systems. The combination of Ethernet, mixed-signal acquisition capability, timer/PWM resources, and ample program memory is particularly useful in systems that must coordinate sensing, communications, and real-time actuation. Board design must account for the 100-pin LQFP footprint, exposed-pad thermal requirements, power-supply sequencing, high-speed signal integrity, and the pin multiplexing supported by the device. Firmware should be built against the exact XMC4700 headers and peripheral configuration rather than assuming that a generic Cortex-M4 pinout applies. This page combines the manufacturer device description, exact ordering information, source-document links, application guidance, and available family comparisons. It also identifies which alternatives preserve the package and ordering family, helping engineers distinguish true PCB-compatible options from devices that merely offer similar processing performance.

RFQ যোগাযোগ
XMC4700F100K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon
XMC4700F100K2048AAXQMA1

XMC4700F100K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon

The Infineon XMC4700F100K2048AAXQMA1 is a 32-bit industrial Arm Cortex-M4 microcontroller operating at up to 144 MHz, with 2048 kB of embedded Flash and 352 kB of SRAM, in a 100-pin LQFP package with an exposed pad. It belongs to the XMC4000 family and integrates Ethernet connectivity for connected industrial equipment. An industrial microcontroller is a semiconductor device designed to execute embedded control, monitoring, and communications functions in equipment operating under sustained environmental and availability requirements. The XMC4700 combines a 32-bit Arm Cortex-M4 processing core with embedded memory and Ethernet peripherals in one device. In the product hierarchy, it belongs to the microcontroller class, within semiconductor and embedded-processing devices. Core features include 144 MHz maximum operation, 2048 kB Flash, 352 kB SRAM, 32-bit architecture, and integrated Ethernet. The embedded Flash provides 2 Mbit of nonvolatile program storage, while the 352 kB SRAM provides working memory for control algorithms, protocol stacks, diagnostics, and communications buffers. The 100-pin LQFP-100 package also supports a compact surface-mount implementation for industrial controller boards. The Cortex-M4 architecture combines general-purpose control processing with digital signal processing instructions and floating-point capabilities suited to embedded control workloads. This architecture allows the XMC4700 to serve as the central processor for motor-control, communications, and industrial automation systems. Integrating Ethernet within the microcontroller reduces the need for separate network-interface hardware when the system design requires an Ethernet-capable controller. Typical applications include industrial Ethernet equipment, factory automation controllers, building automation interfaces, motor-control systems, and connected sensor gateways. The combination of 2048 kB Flash and 352 kB SRAM is particularly useful for firmware, parameter storage, communication stacks, diagnostics, and real-time control tasks. The same feature set also supports test and measurement front ends that require deterministic embedded processing plus Ethernet connectivity. Designers should treat the exposed pad as a thermal and electrical connection rather than an optional mechanical feature. Follow the manufacturer’s pin-description and land-pattern guidance when assigning PCB tracks, and validate the Ethernet implementation against the required PHY, magnetics, isolation, and network-timing requirements. Firmware migration also requires checking peripheral availability and the memory map rather than assuming that all XMC family derivatives are functionally identical. This page combines the manufacturer’s ordering information, memory and clock specifications, package details, qualified drop-in alternatives, comparison parameters, and practical PCB guidance. It is intended to accelerate engineering evaluation while preserving the distinction between a mechanically compatible device and a fully application-qualified replacement.

RFQ যোগাযোগ
XMC4700F144F2048AAXQMA1 - 144MHz ARM MCU | Infineon
XMC4700F144F2048AAXQMA1

XMC4700F144F2048AAXQMA1 - 144MHz ARM MCU | Infineon

Infineon Technologies XMC4700F144F2048AAXQMA1 is an industrial 32-bit ARM Cortex-M4 microcontroller operating at 144 MHz, with 2 MB of embedded Flash memory, 352 KB of RAM, and an Ethernet MAC, packaged in a 144-pin PG-LQFP with an exposed thermal pad. The part combines Cortex-M4 DSP and floating-point capability with the XMC4000 family’s communication and industrial-control peripherals. Its 3.3 V operating supply supports equipment designs that use a conventional industrial embedded-control supply rail. An ARM Cortex-M4 microcontroller is a 32-bit embedded processor that combines general-purpose control processing with single-precision floating-point arithmetic and digital signal processing instructions. Within the product hierarchy, this device belongs to the XMC4000 family of Arm Cortex-M4 microcontrollers, a series designed for industrial communications, motor-control platforms, factory automation, and connected embedded equipment. The Cortex-M4 architecture provides a conventional memory-mapped peripheral model while retaining deterministic interrupt-driven operation. Three principal characteristics define the XMC4700F144F2048AAXQMA1: its 144 MHz Cortex-M4 core, 2 MB of embedded Flash for firmware and constants, and 352 KB of SRAM for working data. The Ethernet MAC adds hardware support for Ethernet-connected control systems without requiring those functions to be implemented entirely in software. The 144-pin LQFP package exposes substantially more I/O than small-outline packages, making the device appropriate for boards combining digital control, analog interfaces, communications, and external memory. The XMC4700 architecture extends the Cortex-M4 core with an Ethernet MAC, high-speed USB, CAN, and additional industrial peripherals. According to the Infineon XMC4700/XMC4800 datasheet and reference manual, the family is intended for energy-efficient embedded-control applications requiring higher processing performance and DSP/FPU capability. Firmware can use the Cortex-M4 hardware floating-point unit for control loops and signal calculations instead of implementing those operations in integer-only software. Typical uses include industrial Ethernet controllers, factory automation nodes, motor-control and power-conversion equipment, communications infrastructure, and embedded gateways. In an Ethernet application, the MCU can manage control tasks while the MAC handles packet processing. Its large Flash capacity supports network stacks, boot code, application firmware, and configuration data, while the 352 KB SRAM provides space for protocol buffers and real-time working sets. Board design must account for the exposed thermal pad, analog supply requirements, high-speed communication impedance control, and the numerous power and ground pins. Place decoupling capacitors close to their associated supply pins, provide continuous ground-plane coverage beneath the device, and follow the manufacturer’s reference-layout and pin-multiplexing guidance. The exposed pad should be connected according to the package drawing and thermal requirements rather than treated as an unused lead. This product page combines manufacturer specifications, verified ordering information, practical interface-planning guidance, and a qualified comparison with the closest identified Infineon ordering variant. It also highlights the Ethernet MAC, Cortex-M4 DSP/FPU capability, memory capacity, package constraints, and the engineering checks that matter most when replacing or redesigning around the XMC4700F144F2048AAXQMA1.

RFQ যোগাযোগ
XMC4700F144K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon
XMC4700F144K2048AAXQMA1

XMC4700F144K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon

Infineon Technologies XMC4700F144K2048AAXQMA1 is a 32-bit Arm Cortex-M4 microcontroller operating at 144 MHz, with 2 MB of flash memory and an Ethernet MAC, housed in a 144-pin LQFP exposed-pad package. The device belongs to the XMC4000 family for industrial applications and combines a high-performance microcontroller core with embedded networking capability. Its orderable configuration is identified as the tray-packaged industrial-grade variant. A microcontroller is a programmable system-on-chip used to supervise sensors, actuators, communications, and control loops. The XMC4000 hierarchy places this component within embedded industrial control, where the Arm Cortex-M4 core executes real-time control software and the integrated Ethernet MAC supports connected equipment. This combination makes the MCU relevant to factory automation, industrial networking, motor-control platforms, and connected industrial sensors. Three headline specifications define the part: a 144 MHz Arm Cortex-M4 core, 2 MB of flash organized as 2M × 8 bits, and a 144-pin PG-LQFP-24 exposed-pad package. The product also includes an Ethernet MAC. Compared with smaller general-purpose MCUs, the 144 MHz core provides greater processing headroom for control algorithms, while 2 MB of flash accommodates embedded code, configuration data, and application-specific routines. The exposed pad assists thermal transfer when the device dissipates power during high-clock-rate operation. The XMC4700 architecture is aimed at embedded industrial control rather than simple utility control. Its Arm Cortex-M4 processor supports efficient handling of control logic, and the Ethernet MAC adds a path for Ethernet-based communication. Exact peripheral assignments, electrical limits, memory organization outside the stated flash capacity, and timing characteristics should be confirmed in the Infineon XMC4700/XMC4800 data sheet and reference manual before final circuit design. Typical applications include industrial Ethernet controllers, programmable logic controllers, factory automation modules, building automation equipment, and industrial sensor gateways. The device can also serve as the central controller in motor-control and embedded communication designs where the XMC4700 platform, Ethernet connectivity, and generous flash capacity are useful. Software development is supported by the XMC4700 ecosystem, while board-level decisions must account for the 144-pin exposed-pad land pattern and associated power, clock, and signal-integrity requirements. For PCB implementation, use the manufacturer package drawing and pin-description tables rather than relying on generic 144-pin LQFP conventions. Place the exposed pad on a solid, low-impedance ground plane and follow the recommended via arrangement. Decoupling networks should be positioned directly beside the relevant supply pins, while external clock and Ethernet lines require controlled return paths to limit coupling into sensitive control signals. This product page combines the verified XMC4700 ordering information, exact flash and clock specifications, package details, source documentation, and application-oriented engineering guidance. It helps designers identify the correct industrial Cortex-M4 device while distinguishing the target order code from related XMC4700 and XMC4800 family members.

RFQ যোগাযোগ
XMC4800-E196K2048AA - 144MHz Cortex-M4 MCU | Infineon
XMC4800-E196K2048AA

XMC4800-E196K2048AA - 144MHz Cortex-M4 MCU | Infineon

Infineon Technologies XMC4800-E196K2048AA is an industrial 32-bit Arm Cortex-M4 microcontroller operating at 144 MHz, with 2048 kB of embedded flash memory, Ethernet connectivity, and a 196-pin PG-LFBGA package. The device belongs to the XMC4000 family and combines a real-time microcontroller core with industrial communication and mixed-signal capabilities. Its stated operating voltage is 3.3 V, and the verified product information identifies the part for embedded industrial control, networked automation, and EtherCAT-connected equipment. An Arm Cortex-M4 microcontroller is a 32-bit embedded processor based on the ARMv7E-M architecture and optimized for real-time control systems. The Cortex-M4 core combines deterministic exception handling, compact instruction processing, and support for efficient digital signal-processing instructions. Within the broader semiconductor hierarchy, this device is an embedded microcontroller, part of the integrated-circuit category, and specifically designed for industrial automation rather than general-purpose computing. The XMC4800-E196K2048AA provides 144 MHz processing performance, 2048 kB of on-chip program flash, and integrated Ethernet. These features allow firmware, communications software, control logic, and field-bus services to execute from one integrated device. The verified product description also identifies on-chip flash and analog or mixed-signal capabilities. Its industrial positioning and stated 125°C ambient-temperature capability distinguish it from general-purpose microcontrollers intended for consumer or office environments. The EtherCAT capability associated with the XMC4800 family is important for industrial automation because EtherCAT provides deterministic Ethernet-based communication between controllers and distributed I/O devices. Integrating communications processing with a 144 MHz Cortex-M4 core can reduce system complexity compared with a separate microcontroller and communications controller. The 196-pin LFBGA package also provides a substantial pin count for mixed-signal, communications, debug, and application-specific interfaces, although its land grid requires careful PCB layout and inspection. Typical applications include EtherCAT servo drives, programmable automation controllers, industrial Ethernet gateways, motor-control equipment, factory-floor I/O modules, and embedded condition-monitoring systems. In each case, the Ethernet interface supports networked control, while the Cortex-M4 processing capacity accommodates real-time algorithms and communications stacks. The 3.3 V supply and 125°C ambient-temperature specification make the device suitable for industrial environments when the complete circuit, storage, and thermal design remain within their respective limits. Designers should verify all 196 BGA assignments against the official Infineon datasheet before layout and must provide suitable decoupling, clock circuitry, programming access, and Ethernet physical-layer implementation. The package requires careful escape routing and assembly inspection, and firmware memory planning should account for the 2048 kB flash capacity. Exact peripheral availability, electrical limits, and recommended operating conditions should be confirmed in the manufacturer datasheet. This page consolidates the verified Infineon specifications, distributor pricing, package information, and practical application guidance. It also distinguishes confirmed drop-in alternatives from variants that cannot safely be treated as replacements, helping engineers evaluate the XMC4800-E196K2048AA without relying on unverified cross-reference listings.

RFQ যোগাযোগ
XMC4800-F144K2048AAXQMA1 - 144MHz Cortex-M4 | Infineon
XMC4800-F144K2048AAXQMA1

XMC4800-F144K2048AAXQMA1 - 144MHz Cortex-M4 | Infineon

The Infineon Technologies XMC4800-F144K2048AAXQMA1 is an industrial 32-bit Arm Cortex-M4 microcontroller with a 144 MHz operating frequency, 2 MB of flash memory, and an integrated EtherCAT node. It is packaged in a 144-pin PG-LQFP-24 package with an exposed pad, providing ample I/O and thermal conduction for industrial automation equipment. An Arm Cortex-M4 microcontroller is a reduced-instruction-set processor for embedded control systems, combining a 32-bit architecture, hardware integer and floating-point processing, deterministic peripherals, and low-power operation. The XMC4800 belongs to the broader hierarchy of microcontroller, embedded processor, real-time control IC, and industrial automation semiconductor. Principal features include a 144 MHz Cortex-M4 core, 2 MB of flash, 352 kB of RAM, and integrated 10/100 Mbit/s Ethernet. The EtherCAT node supports high-speed industrial fieldbus communication without requiring a separate communications ASIC. A rich set of timers, communication interfaces, analog peripherals, and general-purpose I/O makes the device suitable for machinery, motion control, PLC modules, robotics, and distributed automation controllers. The XMC4800-F144K2048AAXQMA1 uses a 3.3 V supply, with the documented operating supply range extending from 3.13 V to 3.63 V. Its 144-pin LQFP footprint exposes substantially more I/O than smaller microcontroller packages. The exposed thermal pad assists heat transfer through the PCB, although final junction temperature depends on copper area, airflow, ambient temperature, switching activity, and the selected I/O configuration. Typical deployments include EtherCAT servo drives, industrial Ethernet controllers, programmable automation equipment, sensor-hub controllers, and compact machine-control modules. The 144 MHz processing rate supports responsive control loops, while the integrated EtherCAT interface reduces board area and software complexity for cyclic fieldbus communication. For a new design, reserve the exposed pad as a thermal and electrical ground connection, follow the manufacturer's pin and land-pattern guidance, and validate power sequencing, bus termination, and signal integrity on a production-intent board. Firmware should also include watchdog recovery, safe-state outputs, and communication supervision for industrial equipment. This page combines manufacturer specifications, ordering information, practical design guidance, and clearly qualified same-brand replacement options. Review the manufacturer datasheet and reference manual before finalizing the PCB, clock, memory, EtherCAT, and safety-critical implementation.

RFQ যোগাযোগ
XMC4800E196K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon
XMC4800E196K2048AAXQMA1

XMC4800E196K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon

Infineon Technologies XMC4800E196K2048AAXQMA1 is a 32-bit Arm Cortex-M4 microcontroller rated up to 144 MHz, with 2 MB of flash memory, integrated Ethernet, and a 196-pin PG-LFBGA-196-2 package. It is designed for industrial automation, connected control, and communications equipment requiring deterministic real-time control alongside a networked system interface. An industrial microcontroller is a semiconductor device that executes embedded control firmware, reads sensor and process inputs, and controls actuators or communications hardware. The XMC4000 family combines an Arm Cortex-M4 processor core with embedded peripherals and Ethernet connectivity in a single integrated circuit, reducing the component count needed for industrial network nodes. Key characteristics include a 144 MHz maximum clock, 2,048 kB of flash, 32-bit processing, and an operating supply identified as 3.3 V. The target ordering code is associated with the PG-LFBGA-196-2 package and tray presentation. Its 196-ball land pattern provides a high pin count suitable for extensive peripheral connections and Ethernet implementation, but it also requires a dense, carefully routed PCB layout. The architecture follows the Arm Cortex-M4 processor model and targets embedded real-time workloads. At 144 MHz, the core provides substantially more instruction throughput than lower-frequency general-purpose control devices, while the integrated Ethernet interface allows network communication without requiring a separate controller. Exact RAM capacity, peripheral inventory, Ethernet details, voltage tolerances, and temperature limits must be confirmed in the manufacturer documentation before schematic release. Typical applications include industrial Ethernet controllers, programmable automation equipment, networked sensors, motor and motion-control systems, industrial gateways, and embedded communications equipment. The combination of local real-time processing and Ethernet connectivity is especially useful where control decisions must occur locally while status, configuration, and diagnostic data are exchanged over a network. PCB implementation should prioritize short return paths for supply and ground, controlled clock routing, and careful assignment of high-speed Ethernet signals. The LFBGA-196 footprint demands adequate escape routing and multilayer-board planning; verify the manufacturer pinout, ball map, exposed-pad requirements, and recommended stack-up before releasing artwork. Provide local decoupling according to the device power architecture and use simulation or measurement to confirm Ethernet signal integrity. This page combines the exact ordering information, key device characteristics, sourcing workflow, replacement guidance, and application-focused design considerations. It also distinguishes confirmed manufacturer information from parameters that require engineering confirmation, helping teams move efficiently from component selection to a manufacturable industrial-control design.

RFQ যোগাযোগ
XMC4800F100K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon
XMC4800F100K2048AAXQMA1

XMC4800F100K2048AAXQMA1 - 144MHz Cortex-M4 MCU | Infineon

The Infineon XMC4800F100K2048AAXQMA1 is a 32-bit Arm Cortex-M4 microcontroller operating at 144 MHz, with 2 MB of embedded flash and 352 kB of SRAM, in a 100-pin PG-LQFP package with an exposed pad. The XMC4800 belongs to the XMC4000 family and combines a Cortex-M4 processor core with Ethernet MAC connectivity for industrial embedded control, connected equipment, and real-time networking designs. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces on one device. In the hierarchy of electronic components, the XMC4800 is an embedded microcontroller, a system-on-chip, and a semiconductor. Its Arm Cortex-M4 architecture supports efficient control processing while the integrated Ethernet MAC adds a dedicated path for industrial Ethernet communication without requiring a separate host interface. The primary device characteristics include a maximum core frequency of 144 MHz, 2 MB of flash memory, and 352 kB of SRAM. The device is offered in a 100-pin LQFP package and supports a 3.3 V operating supply according to distributor specifications. The exposed thermal pad improves heat transfer from the die to the PCB, which is particularly important in compact industrial controllers with sustained Ethernet and peripheral activity. The XMC4800 architecture combines the Cortex-M4 processing core with an Ethernet MAC and a substantial collection of embedded peripherals. Its flash capacity provides room for networking stacks, control firmware, diagnostics, and application code, while 352 kB of SRAM supports packet buffers, real-time tasks, and communication workloads. This combination makes the device useful where deterministic embedded control and network connectivity must share one microcontroller platform. Typical applications include industrial Ethernet gateways, programmable automation controllers, connected sensor systems, building automation equipment, and embedded network interfaces. The Ethernet MAC is particularly valuable for equipment that must exchange real-time process data with supervisory systems. The same platform can also support motor and motion-control designs that require deterministic timing alongside network management. PCB implementation should prioritize a short, continuous return path beneath the exposed pad and adequate thermal-via density. Keep sensitive Ethernet traces away from high-current switching paths, use a controlled-impedance layer stack for the physical Ethernet interface, and follow the manufacturer package drawing for exposed-pad soldering and land-pattern dimensions. Confirm all peripheral assignments, clock requirements, and electrical limits against the manufacturer datasheet before release. This product page consolidates the confirmed device identity, package, memory, processor, and Ethernet information with practical PCB and thermal guidance. It also distinguishes verified drop-in candidates from variants that lack enough evidence for replacement use, helping engineers assess fit, compatibility, and sourcing without relying on generic microcontroller family assumptions.

RFQ যোগাযোগ
XMC4800F144K2048AA - 144MHz Cortex-M4 MCU | Infineon
XMC4800F144K2048AA

XMC4800F144K2048AA - 144MHz Cortex-M4 MCU | Infineon

Infineon XMC4800F144K2048AA is an industrial 32-bit ARM Cortex-M4 microcontroller with a 144 MHz processor, 2048 kB of flash memory, and integrated 10/100 Mbit/s Ethernet connectivity, supplied in a 144-pin LQFP package. The XMC4800 combines general-purpose embedded control with Ethernet and EtherCAT-oriented industrial connectivity in a single device. An ARM Cortex-M4 microcontroller is a 32-bit embedded processor based on the ARMv7E-M architecture family and commonly integrates peripherals, memory interfaces, and real-time control functions. Microcontrollers sit within the broader semiconductor hierarchy and are widely used as the central controller in industrial automation, networking equipment, motor-control systems, and connected embedded products. The XMC4800 specifically targets industrial and energy-efficient real-time applications. The XMC4800's headline characteristics are its 144 MHz Cortex-M4 operating frequency, 2048 kB flash configuration, and 10/100 Mbit/s Ethernet interface. Its flash capacity provides room for application code, networking stacks, and EtherCAT-related software, while the Ethernet interface allows direct connection to industrial networks without requiring a separate controller. Distributor records identify a 12-bit conversion feature and an operating temperature range of -40°C to +125°C. The device belongs to Infineon's XMC4000 family and is presented as an industrial microcontroller with DSP and FPU capabilities in the family documentation. This combination is relevant to industrial controls that must execute control algorithms, communicate over Ethernet, and maintain deterministic timing. The verified distributor listing identifies the component as a 32-bit Cortex-M4 MCU with 2 MB of flash in an LQFP-144-24 package. Typical applications include EtherCAT industrial nodes, factory automation controllers, industrial Ethernet equipment, real-time motor-control platforms, and connected sensor systems. In these systems, the XMC4800 can manage application processing and network communication within one package. Its 144 MHz Cortex-M4 core and integrated Ethernet connectivity reduce the need for separate processing and communication components when board area and integration are priorities. Designers should verify the complete pin assignment, peripheral availability, power requirements, clock configuration, and package details in the manufacturer datasheet before layout. Because this 144-pin LQFP device offers many mixed-signal and interface functions, careful partitioning of power, Ethernet, clock, and debugging nets is important. The complete 144-pin electrical pinout was not included in the supplied verified data and therefore must not be inferred from generic XMC4000 documentation. This page consolidates the verified manufacturer and distributor information, separates known XMC4800 characteristics from missing electrical details, and documents drop-in ordering-code candidates without presenting unverifiable substitutions. It also provides application guidance, comparison parameters, and sourcing considerations for engineers evaluating the XMC4800F144K2048AA.

RFQ যোগাযোগ
XMC6221SCQ024XABXUMA1 - Wireless-Charging MCU | Infineon
XMC6221SCQ024XABXUMA1

XMC6221SCQ024XABXUMA1 - Wireless-Charging MCU | Infineon

Infineon Technologies XMC6221SCQ024XABXUMA1 is a microcontroller IC in the XMC6000 family, specifically the XMC6200 series, designed for adapter and charger applications. The ordered part is also indexed as a wireless charging IC, placing it in the power-management control category associated with wireless power adapters. Its exact package, core configuration, flash capacity, timing range, and electrical limits must be confirmed from the Infineon datasheet and ordering information before a PCB design is released. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interface circuitry into one device. In an adapter or charger, this functional category controls input negotiation, power-stage timing, fault handling, communication, and protection sequencing. The XMC6000 family therefore serves as the embedded control center between the power-conversion hardware and the external charging system. The Infineon product page identifies XMC6221SC-Q024X-AB as an XMC6000-family, XMC6200-series device for adapters and chargers. The full orderable identifier XMC6221SCQ024XABXUMA1 identifies the specific ordering configuration used by distributors. The manufacturer's documentation should be consulted for the exact package dimensions, pin assignments, flash-memory configuration, clock architecture, analog and digital peripherals, operating-voltage range, and temperature ratings. This device is relevant to wireless-charging power adapters that need deterministic control of the primary switching stage and coordinated management of faults. It can also be considered for conventional charger and adapter platforms when the product's voltage, current, communication, and safety requirements match the manufacturer's electrical limits. Firmware qualification, electromagnetic compatibility testing, and production fault-mode analysis remain essential parts of any charger design. Typical design work begins by assigning every XMC6221SCQ024XABXUMA1 pin according to the manufacturer pin-description table and then reviewing the power architecture. The designer should confirm which pins provide supply voltage, ground, reset, programming access, switching-control outputs, and communications. Component population and analog-network values must also follow the reference circuit associated with the selected package and ordering option. Before schematic capture, verify the exact package and exposed-pad requirements directly in the Infineon ordering information. Check the recommended operating area, absolute maximum ratings, flash endurance, clock tolerance, and reset behavior. Layout planning must then provide adequate copper for thermal dissipation and clean grounding for the switching stage, especially when the controller is mounted near a high-current power converter. This product page combines the confirmed XMC6000-family classification, adapter and charger positioning, ordering identifiers, and sourcing links with engineering-focused design guidance. It also distinguishes verified product identity from specifications that still require direct confirmation from the manufacturer datasheet, helping teams evaluate the XMC6221SCQ024XABXUMA1 without overlooking critical footprint and qualification checks.

RFQ যোগাযোগ
XMC6511SCQ040XAAXUMA1 - XMC6500 ARM MCU | Infineon
XMC6511SCQ040XAAXUMA1

XMC6511SCQ040XAAXUMA1 - XMC6500 ARM MCU | Infineon

The Infineon XMC6511SCQ040XAAXUMA1 is an ARM-based microcontroller in the XMC6500 family, with UART interface capability and positioning for light electric vehicles, home audio, information and communications technology, adapters, and PC docking applications. The device is associated with Infineon's XMC1000 product listing, while its ordering designation identifies the XMC6511SC-Q040X-AA configuration. The exact package, core frequency, memory configuration, and electrical limits require confirmation from the manufacturer documentation before schematic or PCB release. An automotive microcontroller is a semiconductor device that executes embedded control software and manages communications between sensors, actuators, vehicle networks, and higher-level vehicle systems. Within the product hierarchy, this part belongs to the microcontroller, embedded processor, ARM microcontroller, and automotive electronics categories. Its UART capability supports serial data exchange, but the available product listing does not establish the number or electrical characteristics of every UART peripheral. The XMC6511SCQ040XAAXUMA1 is identified by Infineon as an XMC6500 family member intended for light-EV and broader industrial consumer applications. Infineon's official product page names light EVs, home audio, ICT, adapters, and PC docking as target areas. A distributor description additionally identifies the device with ARM microcontroller and UART interface categories, confirming its position within the XMC1000 and XMC6500 naming context. Because this orderable suffix represents a specific embedded configuration, firmware support must be selected for the exact XMC6511SC-Q040X-AA device rather than only for the broader XMC6500 family. Designers should verify the available flash and SRAM, CPU characteristics, clock configuration, package dimensions, pin multiplexing, peripheral set, and development-tool compatibility against the current Infineon datasheet and product-page ordering information. Potential deployments include light-EV control modules, home-audio interfaces, ICT equipment, power adapters, and PC-docking products. UART connectivity can support diagnostic links, control messages, external data converters, or module-to-module communication when the final peripheral configuration and pin multiplexing permit the intended interface. These applications require board-level validation of voltage levels, signal timing, bus direction, and firmware initialization. Before layout, confirm the exact package and pin assignment because the orderable code alone does not provide a safe basis for PCB footprint selection. Preserve the manufacturer-recommended decoupling and clock-network implementation, and do not reuse a footprint from another XMC device without comparing every pin mechanically and functionally. Firmware should include brownout, reset, clock-startup, and communication-error handling appropriate to the final power architecture. This product record combines the official Infineon family identification, distributor listing information, ordering details, and practical evaluation guidance. It is intended to help engineers identify the correct device and plan validation, while avoiding assumptions about unreported electrical values, package mechanics, memory capacity, or pin compatibility.

RFQ যোগাযোগ
XMC6521SCQ040XAAXUMA1 - ARM Cortex-M0 Wireless Power MCU | Infineon Technologies
XMC6521SCQ040XAAXUMA1

XMC6521SCQ040XAAXUMA1 - ARM Cortex-M0 Wireless Power MCU | Infineon Technologies

The Infineon Technologies XMC6521SCQ040XAAXUMA1 is an application-specific ARM Cortex-M0 microcontroller in the XMC1000 family, designed for real-time control in wireless power systems. The device is identified as a wireless charging controller MCU with 40 KB of flash memory and a 40-pin VFQFN exposed-pad package. Its ARM Cortex-M0 processor core supports deterministic control of wireless power-transfer systems requiring low-latency peripheral handling and compact embedded processing. An application-specific microcontroller is an integrated circuit optimized for a defined equipment category rather than a general-purpose processor. The XMC1000 family combines an ARM Cortex-M0 core with embedded control peripherals suited to real-time power conversion and communication tasks. This makes the XMC6521SCQ040XAAXUMA1 appropriate for wireless charging transmitters, receivers, power-conversion control, and embedded systems that coordinate coil drive, feedback, protection, and user-interface functions. The XMCXXXXSC series addresses wireless power system control requirements, according to the XMC6521SCQ040XAAXUMA1 datasheet listing. The Cortex-M0 architecture provides a compact instruction set and efficient event-driven execution, while the 40 KB embedded flash supports application firmware for power-loop control, communication protocols, state machines, and system supervision. The 40-VFQFN exposed-pad package supports high-density PCB layouts but requires careful thermal and layout planning. The 40-VFQFN exposed pad improves heat transfer from the device to the PCB when the pad is properly soldered and connected to a thermal plane. In a wireless power converter, the MCU typically supervises bridge or resonant-converter switching decisions, interprets voltage and current feedback, manages fault conditions, and coordinates auxiliary functions such as foreign-object detection or communications. For PCB design, place input and output decoupling capacitors close to the corresponding supply and ground pins, provide a low-impedance return path beneath the exposed pad, and keep high-current switching loops compact. Route sensitive feedback signals away from power-stage switching nodes, use a continuous ground reference, and follow the pin-description table in the manufacturer datasheet when assigning tracks and test points. The XMC6521SCQ040XAAXUMA1 is listed by Infineon Technologies as an ARM Cortex-M0 XMC1000 wireless power controller microcontroller in a 40-VFQFN exposed-pad package. Request the current price, stock status, and lead time through the Request a Quote form on this page.

RFQ যোগাযোগ
XMC7201SCQ024XABXUMA1 - Dual-Core M7 MCU | Infineon
XMC7201SCQ024XABXUMA1

XMC7201SCQ024XABXUMA1 - Dual-Core M7 MCU | Infineon

The Infineon Technologies XMC7201SCQ024XABXUMA1 is an industrial ARM microcontroller in the XMC7200 family, integrating two Arm Cortex-M7 CPUs for primary processing and one Arm Cortex-M0+ CPU for peripheral and security processing. Its embedded connectivity includes Controller Area Network with Flexible Data rate and Gigabit Ethernet, while the complete orderable part is supplied in a grade described by Infineon as having extended longevity, being halogen free, and complying with RoHS. An ARM microcontroller is a programmable semiconductor that integrates a processor core, memory interfaces, communication peripherals, timers, interrupt logic, and general-purpose I/O on one device. In the product hierarchy, the XMC7201SCQ024XABXUMA1 is a 32-bit microcontroller, an embedded-processing IC, and a member of the XMC family designed for industrial control, communications, networking, and connected equipment. The family's defining feature is heterogeneous processing. The two Cortex-M7 cores can divide demanding control and communications workloads, while the Cortex-M0+ core provides an independent domain for peripheral control and security-related tasks. The embedded CAN FD interface supports higher-capacity, flexible automotive or industrial network communication, and Gigabit Ethernet provides high-bandwidth connectivity to a controller, switch, or network infrastructure. The XMC7200 architecture combines those processors with embedded peripherals rather than relying only on external communication devices. CAN FD and Gigabit Ethernet are the clearest application-facing interfaces in the manufacturer datasheet. This makes the family appropriate for industrial gateways, networked controllers, adapter and charger platforms, and connected automation equipment that must combine real-time control with Ethernet communication. Typical uses include industrial Ethernet gateways, CAN FD communication hubs, adapter and charger controllers, programmable automation equipment, and connected industrial sensors. The extended-longevity positioning makes the device especially relevant to industrial programs where supply continuity, PCB compatibility, and lifecycle management matter. Software support should be selected for the complete ordering code rather than only the abbreviated XMC7201SC-Q024X-AB designation. Before schematic capture, confirm the exact lead configuration, exposed-pad requirements, pin multiplexing, and recommended decoupling from the Infineon package drawing and datasheet. Preserve the manufacturer's startup, clock, memory, and peripheral-instantiation requirements. Firmware configuration must account for all three CPU domains and should be validated for interrupt routing, Ethernet initialization, and CAN FD timing. This page organizes the manufacturer specifications, sourcing guidance, application fit, and engineering cautions around the complete XMC7201SCQ024XABXUMA1 ordering code. It also distinguishes the product's industrial connectivity features from generic microcontroller capabilities and highlights the design checks needed before layout or firmware deployment.

RFQ যোগাযোগ
XMC7241SCQ040XAAXUMA1 ARM Microcontroller | Infineon
XMC7241SCQ040XAAXUMA1

XMC7241SCQ040XAAXUMA1 ARM Microcontroller | Infineon

Infineon Technologies XMC7241SCQ040XAAXUMA1 is an ARM microcontroller IC listed in the XMC1000 series and identified by distributor product records as an Infineon microcontroller. The exact orderable suffix identifies an automotive-oriented XMC configuration, while its core architecture, memory configuration, operating limits, peripherals, and package dimensions remain tied to the manufacturer documentation. The device is suitable for compact embedded-control systems that require an established Infineon MCU platform and production sourcing under the exact XMC7241SCQ040XAAXUMA1 ordering code. An ARM microcontroller is a programmable semiconductor that combines a processor core, memory interfaces, peripherals, and communication resources on one integrated circuit. Within the product hierarchy, the XMC device is an embedded microcontroller, part of the ARM MCU category, and belongs to the broader embedded-control semiconductor market. Such devices are programmed to supervise actuators, read sensors, communicate with external circuits, and execute real-time control functions in industrial, automotive, and communications equipment. The decisive selection criteria for this exact MPN are its package, pin arrangement, core specification, flash and SRAM capacity, operating-voltage range, temperature rating, peripheral set, qualification status, and software-development support. These characteristics must be matched against the target PCB and firmware before ordering. The suffix contains the commercial ordering information, but the suffix alone should not be treated as a substitute for the package data table and pin description in the Infineon documentation. This device is intended for embedded applications where a compact ARM-based controller can manage multiple digital interfaces and deterministic control tasks. Relevant designs may include automotive control modules, industrial automation equipment, communications equipment, sensor hubs, and compact power or motor-control systems. Final suitability depends on whether the required peripherals, timing resources, memory, and I/O voltage assumptions match the design. The exact electrical limits must be checked against the worst-case operating conditions rather than inferred from the product family. Before schematic capture, confirm the physical package, exposed-pad requirements, pin multiplexing, and PCB land pattern from the Infineon package drawing. Decoupling, grounding, signal-integrity, and power-distribution layout should follow the reference circuitry in the manufacturer documentation. If the PCB already exists, compare every connected pin, supply requirement, and exposed thermal connection rather than relying only on the XMC family name. This page consolidates the exact commercial MPN, structured purchase information, application guidance, and engineering checks into one product record. It deliberately avoids substituting a visually similar XMC order code. For a controlled new design, request the current manufacturer documentation and use the complete part number shown above as the single source of truth for sourcing, firmware hardware definitions, and PCB compatibility. The Infineon XMC7241SCQ040XAAXUMA1 remains a practical choice when an ARM-based embedded controller is required and the design team can verify the exact package, electrical limits, qualification requirements, and software support. Use the Request a Quote form for current commercial availability and lead-time confirmation. Obtain the manufacturer datasheet and package drawing before releasing the PCB or production BOM.

RFQ যোগাযোগ
XMC7501SCQ040XAAXUMA1 | Infineon Cortex-M0 Power MCU
XMC7501SCQ040XAAXUMA1

XMC7501SCQ040XAAXUMA1 | Infineon Cortex-M0 Power MCU

Infineon XMC7501SCQ040XAAXUMA1 is an ARM Cortex-M0 wireless power controller microcontroller in the XMC1000 family, packaged in a 40-pin VFQFN surface-mount package with an exposed pad. The device combines a 32-bit Cortex-M0 core, embedded FLASH program memory and application-specific wireless power control functions in a compact package designed for embedded power-transfer systems. A wireless power controller microcontroller is a specialized type of embedded microcontroller that manages the transfer of electrical energy between a transmitter and a receiver. It belongs to the microcontroller hierarchy and broader embedded semiconductor category, where real-time control logic coordinates sensing, communication, timing and power-stage commands. Wireless power controller MCUs are especially useful when a product needs configurable communication, safety monitoring and closed-loop regulation between a transmitter coil and its receiver. The XMC7501SCQ040XAAXUMA1 provides an ARM Cortex-M0 processor, FLASH memory and a 40-VFQFN exposed-pad package. Infineon identifies the device as a wireless power controller within the XMC1000 series. The exposed pad supports thermal dissipation when the controller is used in power-conversion equipment. Its integrated flash memory also gives embedded developers a compact implementation environment for control firmware, protocol handling and system supervision. The ARM Cortex-M0 architecture provides a simple, energy-efficient platform for real-time embedded control. Because the MCU is application-specific rather than a general-purpose processor, its peripherals are oriented toward wireless power transfer system functions. Engineers should review the manufacturer datasheet for the exact clock, memory, analog, timing, communication and electrical limits before fixing the firmware architecture or PCB schematic. Typical applications include wireless power transmitter controllers, Qi-compatible charging products, industrial inductive transfer systems, consumer charging cradles, smart-home accessories and compact embedded power modules. The device is particularly relevant where a controller must coordinate coil drive, communication, fault handling and system sequencing while occupying little board area. Design the exposed-pad ground and thermal path according to the manufacturer land-pattern guidance. Keep sensitive timing and communication traces away from high-current switching paths, and confirm that the package, operating voltage, clock configuration and peripheral assignments match the selected board revision. Firmware validation should include coil-startup, overvoltage, undervoltage, over-temperature and communication-loss scenarios. This page organizes the manufacturer identity, package information, engineering use cases, design considerations, sourcing workflow and available cross-reference findings for the XMC7501SCQ040XAAXUMA1, helping engineers move quickly from part selection to schematic review and prototype planning.

RFQ যোগাযোগ
XMC7541SCQ040XAAXUMA1 Wireless Power Controller | Infineon
XMC7541SCQ040XAAXUMA1

XMC7541SCQ040XAAXUMA1 Wireless Power Controller | Infineon

The Infineon Technologies XMC7541SCQ040XAAXUMA1 is an ARM Cortex-M0 XMC1000 wireless power controller microcontroller with integrated flash, designed for wireless power applications and supplied in a 40-pin VFQFN exposed-pad package. The manufacturer identifies the device for PC docking, adapters, home audio, information and communications technology equipment, and light electric vehicles. Its application-specific architecture integrates the control requirements of wireless power systems into a compact embedded microcontroller package. An application-specific microcontroller is a type of embedded processor optimized for a defined equipment class or control function. In the broader hierarchy, it belongs to microcontrollers, embedded semiconductors, and programmable logic devices. Unlike a general-purpose microcontroller that relies more heavily on external peripherals, an application-specific device often combines a core with interfaces and control resources tailored to a particular system. The XMC7541SCQ040XAAXUMA1 is positioned for wireless power control rather than general-purpose computing. The device uses an ARM Cortex-M0 processor core and includes embedded flash memory, reducing the need for separate program storage in many designs. Its 40-VFQFN exposed-pad package supports compact surface-mount layouts while providing a dedicated thermal and electrical connection area beneath the package. The ordering code XMC7541SCQ040XAAXUMA1 identifies the specific configuration, package, qualification, temperature, and shipping option selected for production use. The XMC7541SCQ040XAAXUMA1 belongs to the XMC7000 family according to the Infineon product page. That family is aimed at wireless power and related power-management applications where deterministic embedded control, compact packaging, and application-specific interfaces are valuable. Engineers can use the microcontroller to coordinate transmitter and receiver functions, monitor system conditions, manage fault handling, and support communication between a wireless power subsystem and the surrounding host equipment. Typical implementation areas include wireless power adapters, PC docking systems, home audio equipment, information and communications technology products, and light electric vehicles. In an adapter, the controller can organize the power-conversion control loop and system supervision. In a docking product, it can manage charging coordination and device-specific power policies. In a light electric vehicle, low-voltage control functions may include accessory management, communications, and centralized supervision where the vehicle architecture requires an embedded controller. The principal design consideration is PCB integration. The VFQFN exposed pad requires a properly designed thermal-via and copper-in-land pattern, while power, communications, and sensing paths must be routed to minimize switching noise and signal integrity problems. Firmware, peripheral configuration, safety behavior, and production programming requirements should be validated together rather than treated as independent tasks. This product record combines the manufacturer application positioning, package identification, processor architecture, embedded-memory configuration, package constraints, and verified ordering information with practical implementation guidance. It helps engineers distinguish this specialized wireless power controller from broader XMC devices before beginning schematic capture, footprint design, firmware planning, and production sourcing.

RFQ যোগাযোগ
XMC8231SCQ024XABXUMA1 ARM MCU | Infineon Technologies
XMC8231SCQ024XABXUMA1

XMC8231SCQ024XABXUMA1 ARM MCU | Infineon Technologies

Infineon Technologies XMC8231SCQ024XABXUMA1 is an ARM-based XMC8000 microcontroller intended for industrial adapters and chargers. The device combines embedded control processing, programmable digital interfaces, and mixed-signal peripherals in a single microcontroller platform designed for compact power-conversion equipment. Its RoHS-compliant and halogen-free construction supports environmentally conscious product designs, while the broad integration reduces the need for external control components. An XMC microcontroller belongs to the embedded-processing hierarchy: XMC8000 series microcontroller, ARM microcontroller, 32-bit embedded controller, integrated circuit, and semiconductor. Unlike a discrete logic controller, this device consolidates control logic, peripheral interfaces, timing functions, and analog signal handling around an embedded processor core. That architecture is useful when an industrial power supply needs deterministic supervisory control, communication, fault handling, and configurable analog functions without relying on a separate processor. The XMC8231SC-Q024X-AB ordering family is identified by Infineon as an XMC8000 microcontroller for adapters and chargers. Its RoHS compliance and halogen-free status are stated on the manufacturer product page. These attributes matter for power-supply products because system designers must coordinate environmental requirements with component documentation, production controls, and end-product certifications. Because the complete electrical characteristics table, memory configuration, clock ratings, peripheral list, and package dimensions must be confirmed from the manufacturer datasheet, engineers should use the official ordering information before finalizing a design. In particular, confirm the exact pin assignment, peripheral availability, operating limits, clock configuration, conversion performance, and exposed-pad requirements for the complete ordering code. Typical application roles include digitally controlled adapter power supplies, charger controllers, industrial power-conversion modules, and compact external power supplies. In these systems, the microcontroller can coordinate feedback control, supervise voltage and current conditions, manage protection states, and support communication with a higher-level controller. The integrated approach can also reduce board area and the number of discrete components when compared with a solution assembled from separate logic devices. A successful implementation begins with the manufacturer pin-description and characteristic tables. Verify startup behavior, clock requirements, analog reference handling, communication pins, and the thermal pad connection on the exact package variant. Prototype the control firmware with realistic load transitions and fault cases before production, especially for designs that depend on accurate current measurement or safety-related shutdown behavior. This page organizes the confirmed XMC8000 identity, environmental attributes, application fit, sourcing information, and engineering validation points into a concise engineering reference. Use the manufacturer ordering page and datasheet as the final authority for electrical limits, memory, peripherals, pinout, and lifecycle decisions.

RFQ যোগাযোগ
XMC8511SCQ040XAAXUMA1 - Cortex-M0 Power MCU | Infineon
XMC8511SCQ040XAAXUMA1

XMC8511SCQ040XAAXUMA1 - Cortex-M0 Power MCU | Infineon

The Infineon XMC8511SCQ040XAAXUMA1 is an ARM Cortex-M0 application-specific microcontroller in a 40-pin VQFN exposed-pad package. It belongs to the XMC8500 family for industrial power-control applications, including PC docking, audio systems, electric vehicles, adapters, and chargers. The device combines a 40-pin VQFN footprint, ARM Cortex-M0 processing capability, and embedded flash in a compact surface-mount package. An application-specific microcontroller is a semiconductor that integrates a processor core, memory, and interfaces tailored to a particular equipment category. The XMC8500 family occupies the microcontroller hierarchy within embedded semiconductors and industrial control ICs. Compared with a general-purpose microcontroller, this device is optimized around power-conversion control, peripheral monitoring, communications, and compact industrial-system tasks where deterministic control, limited board area, and integrated control functions are important. The manufacturer identifies the XMC8511SC-Q040X-AA as an industrial XMC8500-family device for PC docking, audio, electric-vehicle, adapter, and charger platforms. Its 40-pin VQFN exposed-pad package supports dense PCB layouts and provides a thermal and electrical connection to the board through its exposed pad. Tape-and-reel packaging supports automated production. The product listing identifies the device as active and RoHS3 compliant. The ARM Cortex-M0 core provides a compact embedded-control architecture for supervisory, sequencing, communication, and power-management tasks. Because the XMC8511 is application-specific rather than a generic Cortex-M0 MCU, designers should use the Infineon pin-description and peripheral-assignment tables when defining board nets. The exposed pad must be connected according to the manufacturer land-pattern and thermal recommendations rather than treated as an optional NC land. Typical applications include wireless power and charging adapters, audio power-control systems, PC docking equipment, electric-vehicle auxiliary controllers, industrial adapters, and compact power-conversion products. In these systems, the MCU can coordinate control loops, supervise analog or power stages through dedicated peripherals, manage communication interfaces, and enforce safe operating sequences. Exact flash, SRAM, clock, analog, and communication ratings should be selected from the exact ordering-code table in the manufacturer datasheet. The primary design consideration is package-aware PCB implementation. Place the exposed pad on a properly sized copper area, follow the manufacturer’s land pattern, and route high-current or fast-switching power-stage connections away from sensitive control signals. Confirm signal levels, pin multiplexing, clock configuration, peripheral availability, and startup behavior against the datasheet before releasing a production schematic. This page organizes the XMC8511SCQ040XAAXUMA1 for engineering evaluation by connecting its product identity, package, compliance, application context, alternative-device assessment, and practical implementation guidance. It is designed to help engineers narrow the correct XMC8500-family option while keeping PCB, firmware, thermal, and sourcing decisions tied to the exact Infineon ordering information.

RFQ যোগাযোগ