মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC12F635-E/SN - 8-bit MCU, 1.75KB Flash, 20MHz, 8-SOIC | Microchip
PIC12F635-E/SN

PIC12F635-E/SN - 8-bit MCU, 1.75KB Flash, 20MHz, 8-SOIC | Microchip

The Microchip Technology PIC12F635-E/SN is an 8-bit Flash-based CMOS microcontroller in the PIC12 mid-range family, housed in an 8-pin SOIC (SN) package. It integrates 1.75 KB of Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM, and executes instructions at up to 20 MHz from an internal oscillator or external clock source. The device features 6 general-purpose I/O pins plus an input-only pin, an enhanced capture/compare/PWM (ECCP) module, and Microchip's nanoWatt power-management technology for ultra-low standby current. An 8-bit microcontroller is a single-chip computer that processes data 8 bits at a time and typically integrates a CPU, program memory (Flash/ROM), data memory (SRAM), non-volatile storage (EEPROM), timers, communication peripherals, and I/O pins onto one silicon die. Within the broader taxonomy, 8-bit MCUs sit beneath 16-bit and 32-bit MCUs in processing capability, but lead in cost-effectiveness, deterministic interrupt response, and ultra-low power consumption, making them dominant in compact embedded designs. The PIC12F635 belongs to Microchip's PIC12 sub-family, which targets low pin count (8-14 pins) cost-sensitive applications where space, BOM cost, and battery life matter most. Key features include a wide operating voltage range of 2.0V to 5.5V, an internal 4 MHz high-precision oscillator (factory calibrated to ±1%), 10-bit A/D converter with up to 4 input channels, an enhanced USART, an 8-bit/16-bit timer, and a hardware comparator. The nanoWatt technology provides multiple low-power modes (Run, Idle, Sleep) with standby currents as low as 50 nA typical, enabling multi-year battery life on small coin cells. The PIC12F635 architecture uses a 14-bit wide instruction word with single-cycle execution except for branches, providing predictable timing critical for real-time control. Its enhanced mid-range core adds hardware multiply, larger stack, and prioritized interrupts versus baseline PIC devices, making it suitable for applications requiring deterministic response. Typical applications include remote control transmitters, sensor signal conditioning, automotive body electronics, lighting controllers, RF tag readers, battery-powered consumer devices, and small appliance controls. The 8-pin footprint fits space-constrained PCB layouts while still providing enough peripherals for typical sensor-interface and actuator-control tasks. When designing with this MCU, ensure the MCLR pin is pulled high through a 10 kΩ resistor for normal operation, place a 0.1 µF decoupling capacitor close to VDD, and configure unused I/O pins as outputs to minimize current draw. The internal oscillator eliminates external crystal cost but allows external crystal mode if higher frequency accuracy is needed. This page synthesizes distributor pricing, parametric comparison, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC12F635-I/MD - 8-bit Flash MCU, 1.75KB, 20MHz, 8-DFN | Microchip
PIC12F635-I/MD

PIC12F635-I/MD - 8-bit Flash MCU, 1.75KB, 20MHz, 8-DFN | Microchip

The Microchip Technology PIC12F635-I/MD is an 8-bit flash-based CMOS microcontroller from the PIC12 family, featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM, all housed in an 8-pin DFN (4x4 mm) surface-mount package with an exposed pad. It operates at a maximum clock speed of 20 MHz, supports supply voltages from 2.0 V to 5.5 V (industrial-grade), and is rated for an operating temperature range of -40 °C to +85 °C. The device integrates Microchip's nanoWatt technology, delivering extremely low power consumption suitable for battery-powered and energy-harvesting applications. An 8-bit PIC microcontroller is a RISC-based single-chip computer built around a Harvard architecture that separates program and data memory, enabling simultaneous instruction fetch and data access. The PIC12 sub-family targets ultra-compact, low-pin-count designs where 6 or fewer I/O lines are sufficient - typical examples include appliance controls, sensor nodes, remote keyless entry, and small motor drivers. Compared to larger PIC16/PIC18 devices, the PIC12 family sacrifices peripherals and memory for the smallest possible PCB footprint, making it the de facto choice when board area is at a premium. Key features of the PIC12F635 include a precision 8 MHz internal oscillator with PLL for 32 kHz to 20 MHz operation, an integrated analog comparator, a 10-bit ADC (not present on all 8-pin PIC12s - the PIC12F635 specifically excludes this), a hardware UART (EUART), capture/compare/PWM (CCP) module, and a watchdog timer with its own on-chip low-power oscillator. The device also supports in-circuit serial programming (ICSP) and in-circuit debugging (ICD) via two dedicated pins. nanoWatt features include Sleep mode currents in the microamp range, multiple oscillator options, and peripheral module disable to quiesce unused functions. Typical applications include remote-control transmitters, sensor signal conditioning, automotive RKE (remote keyless entry) receivers, security-system peripherals, battery chargers, LED drivers, and small consumer appliances. The 8-pin DFN package reduces PCB area by approximately 85% versus the PDIP-8 equivalent, enabling use in space-constrained designs such as wearable patches, RFID transponders, and IoT edge nodes. When designing with this part, leave the ICSPDAT/ICSPCLK pins accessible (RA0/RA1) for production programming and debugging. Decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of the package, and connect the exposed thermal pad to ground for improved thermal dissipation and mechanical solder joint reliability. This page synthesizes Microchip datasheet specifications, current distributor pricing, and drop-in same-package alternatives (PIC12F635-I/MF, PIC12F609-I/MD, PIC12F615-I/MD) not aggregated in a single view elsewhere.

RFQ যোগাযোগ
PIC12F635-I/MF - 8-Bit MCU, 20MHz, 1.75KB Flash, 8-DFN | Microchip
PIC12F635-I/MF

PIC12F635-I/MF - 8-Bit MCU, 20MHz, 1.75KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12F635-I/MF is an 8-bit PIC microcontroller featuring a RISC CPU architecture, 1.75 KB of Flash program memory (1K x 14 words), 64 bytes of SRAM, and 128 bytes of EEPROM, all housed in a compact 8-pin DFN-S (6x5 mm) surface-mount package. It executes instructions at up to 20 MHz and integrates six general-purpose I/O pins, one enhanced comparator, an internal oscillator, two 8/16-bit timers with watchdog, brown-out detect (BOD), power-on reset (POR), and an A/D converter-less nanoWatt sleep architecture. The industrial-grade -I variant operates across a -40C to +85C ambient range and accepts a 2.0V to 5.5V supply. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, RAM, and peripherals on a single die. The PIC10/12 family of mid-range core MCUs is widely used as cost-optimized glue logic and sensor interface controllers in space-constrained designs. Within the broader taxonomy, PIC12F635 belongs to the enhanced mid-range 8-bit MCU category, with its RISC single-cycle instruction set delivering deterministic interrupt latency and ~5 MIPS peak throughput at 20 MHz, suitable for deterministic control loops where a 32-bit MCU would be over-spec. Key features include nanoWatt power management with multiple sleep modes (typically sub-1 uA standby), a hardware USART/SPI/I2C-capable EUSART block on selected variants, internal 4 MHz and 31 kHz oscillators reducing external component count, and Microchip's In-Circuit Serial Programming (ICSP) interface for field upgrades. The on-chip enhanced comparator supports analog signal conditioning without an external op-amp, while two timer/counters and a watchdog timer enable closed-loop control and fail-safe operation. Programming is supported by the free MPLAB X IDE and XC8 compiler toolchain. The device targets cost-sensitive 8-bit applications including PIR motion sensor signal chains, battery-powered remote controls, LED driver controllers, fan/relay control, security PIR front-ends, simple sensor nodes, and consumer appliance user-interface sub-MCUs. Its 8-pin DFN package keeps the board footprint to roughly 6x5 mm while exposing six I/O pins through multiplexed peripheral functions. Typical designs pair the PIC12F635-I/MF with a 3V coin cell or USB-powered linear regulator, a small EEPROM or sensor on the I2C bus, and a low-side MOSFET or opto-triac load driver. When designing with the PIC12F635-I/MF, ensure decoupling is placed within 3 mm of VDD with at least a 100 nF X7R ceramic plus a bulk tantalum. Reserve GP3/MCLR for the ICSP programming header unless the internal MCLR disable is configured, and respect the 20 MHz maximum Fosc when VDD drops below 4.5V (4.5V-5.5V required for full-speed operation). This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC12F635-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology
PIC12F635-I/P

PIC12F635-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology

The Microchip Technology PIC12F635-I/P is a CMOS Flash-based 8-bit PIC microcontroller operating up to 20 MHz, with 1.75 KB of program Flash memory and 64 bytes of RAM. The device provides six general-purpose I/O pins and is supplied in an 8-pin PDIP package. Its -I grade identifies the industrial temperature option, while the /P suffix identifies the through-hole package. A microcontroller is a programmable integrated circuit that combines a CPU core, memory, I/O ports, and peripherals on one semiconductor device. The PIC12F635 belongs to the PIC12 family of 8-bit RISC microcontrollers, where RISC means the processor uses a compact, predominantly single-word instruction set. The manufacturer states that programmers need only 35 single-word instructions, reducing learning and code-development effort for compact control systems. Key device capabilities include up to 20 MHz operation, Flash program memory, 64 bytes of RAM, six I/O ports, and one comparator. Microchip's product page also identifies a KeeLoq-compatible cryptographic module and programmable low-voltage detection. These features allow the PIC12F635-I/P to combine basic embedded control, threshold monitoring, and selected security-oriented processing without requiring a larger system controller. The PIC architecture uses separate program and data memory spaces and supports efficient control of embedded I/O. At an operating frequency as high as 20 MHz, firmware can support time-sensitive state machines, switching control, signal conditioning, and low-complexity communication tasks. Exact timing, memory-map, peripheral, and electrical details should be confirmed against the manufacturer datasheet before final firmware and PCB design. Typical uses include compact remote controls, battery-powered sensing nodes, simple security modules, programmable switching products, industrial auxiliary controllers, and low-cost embedded-control boards. The six available I/O pins make the device most suitable where the external interface is limited and the control task does not require extensive communications or high pin counts. Designers should reserve the programming interface, maintain the required oscillator and decoupling layout, and verify the exact I/O direction and analog functions assigned to each pin. Because firmware and peripherals depend on device configuration bits, production designs should follow the manufacturer programming and development-tool guidance rather than assuming behavior from another PIC model. This product page consolidates the verified manufacturer and distributor details for the PIC12F635-I/P and distinguishes confirmed characteristics from data that still requires direct datasheet review. It also organizes purchasing, pinout, comparison, application, and replacement questions around the exact 8-pin PDIP device rather than package or grade variants.

RFQ যোগাযোগ
PIC12F635T-I/MD - 8-bit PIC MCU, 1.75KB Flash, 6 I/O | Microchip
PIC12F635T-I/MD

PIC12F635T-I/MD - 8-bit PIC MCU, 1.75KB Flash, 6 I/O | Microchip

The Microchip PIC12F635T-I/MD is an 8-bit PIC RISC microcontroller with 1.75 KB of Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM, housed in an 8-pin DFN (3 x 3 mm) package with an exposed thermal pad. It operates from 2.0 V to 5.5 V and reaches 20 MHz instruction execution from its internal oscillator, providing a complete compute platform in a footprint smaller than a fingernail. This part is rated for the -40 C to +85 C industrial range and ships on Tape and Reel. An 8-bit PIC microcontroller is a low-power, deterministic single-core processor built on a Harvard architecture with separate program and data buses, belonging to the broader microcontroller -> embedded controller -> semiconductor category. Its strengths are low cost, low quiescent current, fast interrupt response, and a tiny instruction set that compiles to highly compact code - making PIC MCUs dominant in cost-sensitive, pin-constrained, battery-powered applications such as remote controls, sensor nodes, and appliance front panels. Key features include 6 general-purpose I/O pins (each capable of interrupt-on-change and weak pull-up), one analog comparator with internal programmable reference, an 8-bit and a 16-bit timer, a hardware UART, and the LF (low-frequency) signal-chain block for KEELOQ-compatible security learning applications. The device includes an internal 4/8 MHz oscillator calibrated to +/-1 percent, supporting both INTOSC and low-power LFINTOSC modes for sleep-current-sensitive designs. Hardware diagnostic features such as on-chip debug and In-Circuit Serial Programming (ICSP) are retained on dedicated pins. Architecturally, the PIC12F635 uses a 14-bit wide instruction word with single-cycle execution except for program branches, and an 8-level deep hardware stack. The AES encryption engine, security lock bits, and KEELOQ decoder are integrated to support encrypted remote-entry receivers. Internal peripherals connect via an 8-bit data bus and are mapped into the SFR space; the device supports up to 256 bytes of register-mapped SRAM with banked access for low-end C compilers. Typical applications include automotive RKE/remote keyless entry receivers, secure token and authentication peripherals, simple sensor signal-conditioning front ends with on-chip comparator output, low-power remote-control transmitters, and consumer appliance user-interface controllers. The DFN-8 package is suited to space-limited designs where height must stay under 1 mm, including key fobs, smart-card readers, and sealed sensor pods. When designing with this device, place the ICSPDAT/ICSPCLK trace pair symmetrically to avoid coupling noise into the analog comparator input, and provide a bulk decoupling capacitor (>=1 uF) plus a high-frequency 100 nF cap directly across VDD/VSS. Programming must leave both the clock and data ICSP lines accessible through test points or pads to allow in-field firmware updates via Microchip's MPLAB tools.

RFQ যোগাযোগ
PIC12F635T-I/SN - 8-bit 20MHz MCU 1.75KB Flash 8-SOIC | Microchip
PIC12F635T-I/SN

PIC12F635T-I/SN - 8-bit 20MHz MCU 1.75KB Flash 8-SOIC | Microchip

The Microchip Technology PIC12F635T-I/SN is an 8-bit PIC RISC microcontroller running at up to 20 MHz with 1.75 KB (1K x 14) of FLASH program memory and 64 bytes of data RAM, housed in an 8-pin SOIC package. The device integrates six general-purpose I/O pins, an internal oscillator, and on-chip peripherals including two comparators, a 16-bit timer (Timer1 with its own oscillator), an 8-bit Timer0, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), a Watchdog Timer, Brown-Out Detect (BOD), and Power-On Reset (POR). The "T" suffix indicates Tape-and-Reel packaging. A microcontroller (MCU) is a single-chip computer that contains a processor core, non-volatile program memory, volatile data memory, and peripherals such as timers, communication interfaces, and analog blocks. In the component taxonomy, the PIC12F635 belongs to the PIC12 mid-range family -> 8-bit PIC microcontrollers -> microcontrollers (MCU) -> embedded processors -> integrated circuits (ICs). The mid-range core implements a 14-bit instruction set optimized for compact code density in low-pin-count applications. Key features of the PIC12F635T-I/SN include: 1.75 KB self-programmable FLASH (100K erase/write cycles typical), 64 bytes SRAM, 128 bytes EEPROM, an internal 4 MHz / 8 MHz oscillator configurable to 31 kHz LF, hardware EUSART for RS-232/RS-485 links, two analog comparators with programmable reference, an extended instruction set for C-compiler efficiency, and nanoWatt power management with multiple sleep modes. The device operates from 2.0 V to 5.5 V across the -40 C to +85 C industrial temperature range. The PIC12F635 uses Microchip's enhanced mid-range 8-bit core with a hardware multiply, indirect/relative addressing, and a single-cycle instruction pipeline at 20 MHz (200 ns instruction cycle). On-chip in-circuit debug (ICD) and In-Circuit Serial Programming (ICSP) eliminate the need for an external programmer for development and field firmware updates, lowering total BOM cost. Typical applications include low-cost sensor interface nodes, PIR motion detectors, LED dimming controllers, battery chargers, automotive body controllers, small appliance controls, and remote RF transmitter companion logic. The internal oscillator plus nanoWatt modes make the part especially attractive for battery-powered designs where 8 pins are sufficient. When designing with the PIC12F635T-I/SN, observe the absolute-maximum VDD of 7.5 V and place a 0.1 uF decoupling capacitor within 3 mm of the VDD pin. For analog comparator or ADC-like voltage references, add a 10 uF bulk capacitor to reduce switching noise. Always run Microchip's MPASM or XC8 toolchain with the --ROM option below 1.75 KB to preserve ICD space. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC12F family, and practical design notes not consolidated in the Microchip datasheet.

RFQ যোগাযোগ
PIC12F675-E/MD - 8-bit 20MHz MCU, 1.75KB Flash, 8-DFN | Microchip
PIC12F675-E/MD

PIC12F675-E/MD - 8-bit 20MHz MCU, 1.75KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12F675-E/MD is an 8-bit CMOS Flash-based microcontroller (MCU) from the PIC12F family, offering 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM in an 8-pin DFN (4x4 mm, MD suffix) surface-mount package. It executes instructions at 20MHz with a 200ns instruction cycle, integrates a 10-bit 4-channel Analog-to-Digital Converter (ADC), one 8-bit timer and one 16-bit timer, an enhanced Capture/Compare/PWM (CCP) module, and an internal 4MHz/8MHz oscillator. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM/EEPROM), and peripherals (ADC, timers, I/O, communication interfaces) on one die. The PIC12F675 belongs to Microchip's PIC12F "low pin count" family (8-bit PIC -> microcontroller -> semiconductor IC). Within the broader taxonomy, this places it as: PIC12F675 -> PIC12F low-pin-count family -> PIC16-bit architecture family -> 8-bit microcontroller -> embedded MCU -> integrated circuit. This category is widely used for compact, cost-sensitive embedded applications where 8-pin devices with on-chip analog are needed. Key features include 6 I/O pins, an extended operating temperature range of -40C to +125C, on-chip debug support via the ICD interface, and an 8-pin 4x4mm DFN package enabling miniaturized designs. The device operates from 2.0V to 5.5V supply across its temperature range. The PIC12F675 uses a RISC-based Harvard architecture with 35 single-word instructions, providing deterministic interrupt response. Its 10-bit ADC supports four input channels multiplexed onto the I/O pins, and the comparator module supports analog signal conditioning without external components. The internal oscillator eliminates external crystal cost in cost-sensitive designs. Typical applications include battery chargers, LED drivers, fan controllers, small appliance controls, and sensor interface nodes. The integrated ADC and timers make the part well suited for closed-loop analog control tasks. When designing with the PIC12F675-E/MD, use the MPLAB X IDE with the XC8 compiler and an ICD debugger for in-circuit programming and debug. The DFN (MD) package requires careful PCB layout because it has no exposed leads; reflow profile must follow JEDEC J-STD-020, and PCB land pattern must follow the package outline to avoid solder joint defects. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the bare manufacturer datasheet.

RFQ যোগাযোগ
PIC12F675-E/MF - 8-Bit 20MHz Flash MCU, 1.75KB | Microchip
PIC12F675-E/MF

PIC12F675-E/MF - 8-Bit 20MHz Flash MCU, 1.75KB | Microchip

The Microchip Technology PIC12F675-E/MF is an 8-bit CMOS Flash-based microcontroller from the PIC12F family, delivering 20 MHz instruction execution (200 ns instruction cycle) in an 8-pin DFN-S (6x5 mm) surface-mount package. It integrates 1.75 KB of Flash program memory (1K x 14 words), 64 bytes of SRAM, and 128 bytes of EEPROM data memory, with 6 general-purpose I/O pins. According to the Microchip product page, this MCU targets applications requiring compact form factor and integrated analog. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O - it executes firmware to read sensors, drive actuators, and communicate with other ICs. Within the broader semiconductor taxonomy, the PIC12F675 sits in the hierarchy: microcontroller -> 8-bit MCU -> PIC microcontroller -> PIC12F family -> Microchip 8-bit Flash MCUs. Its integrated 10-bit ADC and analog comparator make it a drop-in choice for low-pin-count analog and digital control tasks where a small package and low BOM count matter. Key features include: 8-bit RISC architecture with only 35 single-word instructions, hardware interrupt controller with 8-level deep hardware stack, four-channel 10-bit Analog-to-Digital Converter (ADC) with 4 input channels, one analog comparator, and an internal 4 MHz oscillator (calibrated to +/-1 percent). The wide 2.0 V to 5.5 V supply range (per Microchip datasheet 41180 - refer to the manufacturer datasheet for the latest revision) supports both 3.3 V and 5 V systems, while an on-chip 4 MHz internal oscillator can eliminate the external resonator entirely in cost-sensitive designs. From an architectural perspective, the PIC12F675 uses a Harvard-class RISC core with a 14-bit instruction word. The Flash-based program memory is in-circuit serial programmable (ICSP) via two pins (ICSPCLK/ICSPDAT), enabling in-system firmware updates. An on-chip MCLR and Power-on Reset (POR) circuit plus Brown-out Detect (BOD) protect against fault conditions. The 'E' suffix designates the extended industrial temperature range of -40 C to +125 C; the 'MF' suffix denotes the 8-lead DFN (Dual Flat No-lead) package, also written as DFN-S 6 x 5 mm. Typical applications include low-pin-count analog sensor interfaces, LED lighting controllers, battery chargers, small appliances, and consumer handheld products. The integrated ADC and comparator allow direct thermistor, photocell, or potentiometer signal conditioning without external op-amps, while the 6 GPIO lines can drive indicator LEDs, relays, or push-button inputs. When designing with this device, ensure the supply voltage stays within the published operating range and that ICSPCLK/ICSPDAT lines are isolated from high-current traces to avoid programming noise. The internal 4 MHz oscillator is calibrated at the factory; for timing-sensitive UART or PWM applications, consider an external crystal for higher accuracy. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, providing a one-stop reference for engineers sourcing the PIC12F675-E/MF.

RFQ যোগাযোগ
PIC12F675-E/P - 8-bit MCU, 1.75KB Flash, 20MHz, 8-PDIP | Microchip
PIC12F675-E/P

PIC12F675-E/P - 8-bit MCU, 1.75KB Flash, 20MHz, 8-PDIP | Microchip

The Microchip Technology PIC12F675-E/P is an 8-bit CMOS Flash-based microcontroller from the PIC® 12F family, featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM data memory, all housed in an 8-pin PDIP through-hole package. The device executes instructions in a 200 ns cycle (5 MHz oscillator / 20 MHz instruction rate, four clocks per instruction) and is rated for an extended industrial temperature range of -40 °C to +125 °C, as indicated by the "E" suffix. An 8-bit microcontroller is a small, self-contained computing IC that combines a CPU, non-volatile program memory, working RAM, data EEPROM, and configurable peripherals on a single die. The PIC® 12F family is the smallest-footprint branch of Microchip's mid-range PIC® architecture, designed for low pin count (8-pin) applications where PCB area and BOM cost dominate. Inside the PIC12F675, the mid-range CPU core is paired with a 10-bit A/D converter (4 channels), an analog comparator, a capture/compare/PWM module, an internal 4 MHz oscillator, and a 4 MHz internal RC calibrated to ±1 %. The part is supported by Microchip's MPLAB X IDE and the free MPLAB XC8 C compiler. Key features include six general-purpose I/O pins with individual direction control, a precision 4 MHz internal oscillator eliminating the need for an external crystal in many designs, in-circuit serial programming (ICSP) via two pins (GP0/GP1), and a wide operating voltage range of 2.0 V to 5.5 V. The device also provides a hardware USART (not present on the smaller PIC12F629), 10-bit PWM, and a configurable watchdog timer with its own on-chip low-power oscillator for maximum reliability. Power management features include nanoWatt technology with multiple idle and sleep modes that drop quiescent current into the microamp range. Typical applications include battery-powered sensor nodes, automotive body and lighting controllers, white-goods and HVAC interfaces, low-cost consumer remote controls, LED drivers, and simple closed-loop fan or pump controllers. The wide 2.0-5.5 V supply range allows direct connection to single-cell lithium, two-cell AA, or 5 V regulated rails without level shifting. When designing with the PIC12F675-E/P, place a 100 nF decoupling capacitor within 5 mm of VDD and tie the MCLR pin to VDD through a 10 kΩ pull-up for normal operation. Because the part offers only six usable I/O lines, plan pin allocation carefully - reserving GP0/GP1 for ICSP allows in-circuit firmware updates after PCB assembly.

RFQ যোগাযোগ
PIC12F675-E/SN - 8-Bit 20MHz 1.75KB Flash MCU SOIC-8 | Microchip
PIC12F675-E/SN

PIC12F675-E/SN - 8-Bit 20MHz 1.75KB Flash MCU SOIC-8 | Microchip

The Microchip Technology PIC12F675-E/SN is an 8-bit CMOS Flash-based microcontroller in an 8-pin SOIC package, featuring a 20MHz CPU, 1.75KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM data memory. Operating from 2.0V to 5.5V, it integrates a 10-bit A/D converter with 4 input channels, a single analog comparator, and 6 general-purpose I/O pins in a compact 8-pin footprint. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals around an 8-bit data bus. The PIC12F675 belongs to the PIC10/12/16 mid-range family of microcontrollers -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. Microchip's PIC architecture uses a Harvard RISC design with only 35 single-word instructions, enabling 200ns instruction execution at 20MHz. This combination of compact code density, deterministic timing, and self-contained peripherals makes the PIC12F675 a reference baseline for cost-sensitive embedded control in appliance, sensor, and lighting applications. Key features of the PIC12F675-E/SN include 4 channels of 10-bit ADC with voltage reference, one analog comparator with programmable on-chip reference, an internal 4MHz oscillator (calibrated to ±1%), an internal 20MHz RC oscillator option, an enhanced universal synchronous/asynchronous receiver-transmitter (EUSART) for serial communication, and in-circuit serial programming (ICSP) for field-upgradeable firmware. The 'E' suffix denotes the extended industrial temperature range of -40C to +125C, which is critical for outdoor, automotive under-hood, and industrial environments. Architecturally, the PIC12F675 uses a 14-bit wide instruction word with single-cycle execution except for program branches (two cycles). The Flash program memory is rated for 100,000 erase/write cycles and EEPROM data memory for 1,000,000 cycles, supporting firmware that stores calibration, configuration, or runtime counters in non-volatile memory. The device's nanoWatt power management suite includes multiple power-managed operating modes (Run, Idle, Sleep) and wake-on-change I/O to minimize quiescent current in battery-powered designs. Typical applications include PIR motion sensor signal conditioning, LED lighting controllers, battery chargers, smart sensor nodes, fan controllers, smoke detectors, and simple user-interface controllers (button + LED, I2C slave). The on-chip comparator and ADC enable direct interfacing with analog sensors (temperature, light, gas), eliminating the need for external signal conditioning and shrinking the BOM in space-constrained designs. A primary design consideration is the supply voltage: the PIC12F675-E/SN is rated 2.0V to 5.5V; for designs that need operation below 2.0V or that require higher ADC resolution, consider the PIC12F683 (10-bit ADC, more memory) or PIC12F1840 (7-bit DAC, more peripherals) as functional upgrades that retain the 8-pin SOIC footprint. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F675-I/MD - 8-bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip
PIC12F675-I/MD

PIC12F675-I/MD - 8-bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

The Microchip Technology PIC12F675-I/MD is a low-pin-count 8-bit CMOS Flash-based PIC microcontroller executing instructions in 200 ns, integrating 1.75KB (1K x 14) of Flash program memory, 64 bytes of SRAM and 128 bytes of EEPROM inside an 8-pin DFN (4x4 mm) package. The core is rated up to 20 MHz, supports 35 single-word instructions and ships with 6 general-purpose I/O, a 10-bit ADC with 4 channels, one 8-bit and one 16-bit timer, and an internal 4 MHz oscillator. Operating supply voltage spans 2.0 V to 5.5 V across the industrial temperature range of -40 °C to +85 °C. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as timers, ADC and communication interfaces. PIC microcontrollers from Microchip use a RISC Harvard architecture with separate program and data buses; the PIC12 mid-range family is the canonical 8-bit workhorse for cost-sensitive embedded control. The PIC12F675 sits at the low end of the PIC12 lineup, where it has become a reference design for compact sensor and switch interfaces thanks to its tiny footprint, on-chip EEPROM, internal oscillator and NanoWatt power management. In the product hierarchy, the PIC12F675 belongs to microcontrollers (MCU) > 8-bit MCU > PIC12 mid-range family > CMOS Flash-based devices. Key differentiating specifications include the integrated 10-bit 4-channel ADC with internal voltage reference, hardware USART not present (only GPIO, timers and comparator), 64-byte SRAM and on-chip 128-byte EEPROM for parameter storage, and a NanoWatt power-saving mode that drops quiescent current below 1 µA. The /MD package is a leadless 8-pin DFN (4x4 mm) suited to high-density SMT layouts, while the same silicon is also offered as DIP (/P), SOIC (/SN), and DFN (/MF) variants. Typical applications include battery chargers, LED drivers, sensor conditioning front-ends, remote controls, security and alarm panels, and low-cost consumer appliances where the on-chip ADC, EEPROM and tiny 8-pin footprint minimise external components. The internal 4 MHz oscillator and 4-channel ADC further reduce BOM cost by eliminating an external crystal and signal-conditioning circuitry. When designing with this device, observe that the 6 I/O pins are multiplexed with the ADC inputs and comparator; ensure that any pin shared with the ADC is not driving a heavy load when conversions are in progress. Use the NanoWatt sleep mode with the internal oscillator to minimise standby current in battery-powered nodes, and reserve at least 10% of Flash for in-application updates and bootloader use.

RFQ যোগাযোগ
PIC12F675-I/MF - 8-bit Flash MCU, 1.75KB, 10-bit ADC | Microchip
PIC12F675-I/MF

PIC12F675-I/MF - 8-bit Flash MCU, 1.75KB, 10-bit ADC | Microchip

The Microchip PIC12F675-I/MF is an 8-bit Flash-based CMOS microcontroller delivering 20 MHz CPU performance in an 8-pin DFN (3 x 3 mm, 0.90 mm height) package. It integrates 1.75 KB of Flash program memory, 64 bytes of SRAM, 128 bytes of EEPROM, a 10-bit A/D converter with 4 input channels, and a single analog comparator. The /MF suffix denotes the industrial temperature grade (-40C to +85C) and the DFN-S EP surface-mount package. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, RAM, and peripherals designed to execute embedded control tasks. The PIC12F675 belongs to Microchip's mid-range 8-bit PIC architecture, positioning it within a hierarchy of microcontrollers -> 8-bit MCUs -> PIC microcontrollers -> flash-based MCUs -> semiconductor ICs. Its ultra-compact 8-pin footprint makes it one of the smallest PIC microcontrollers available while retaining on-chip ADC and EEPROM resources. Key features include 35 single-word instructions, 200 ns instruction execution, an internal 4 MHz oscillator, an 8-bit timer (TMR0) and a 16-bit timer (TMR1), a watchdog timer with on-chip oscillator, in-circuit serial programming (ICSP), and a 4-channel 10-bit ADC. The integrated brown-out detect, power-on reset, and wide operating voltage range (2.0 V to 5.5 V) simplify robust power supply design. The PIC12F675 uses a RISC-style Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. With only 35 instructions to learn, the device targets fast firmware development. The internal oscillator eliminates the need for an external crystal in cost-sensitive designs, reducing BOM count and PCB area. Typical applications include consumer appliance control, sensor interface conditioning, battery-powered timers, LED lighting controllers, hobbyist projects, and small sensor node prototypes. The integrated 10-bit ADC allows direct interfacing with analog sensors such as thermistors, photocells, and potentiometers without an external ADC. When designing with this part, route GP3/MCLR with care because it is the only true 5 V tolerant input, and add a series resistor if programming in-circuit. Place a 100 nF decoupling capacitor close to VDD and a bulk capacitor if driving high-current loads from GPIO pins. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F675-I/P - 8-Bit 20MHz Flash MCU | Microchip
PIC12F675-I/P

PIC12F675-I/P - 8-Bit 20MHz Flash MCU | Microchip

The Microchip Technology PIC12F675-I/P is an 8-bit CMOS Flash-based PIC microcontroller with a 20 MHz maximum clock, 1.75 KB of Flash memory, 128 bytes of EEPROM, and a 10-bit A/D converter. It is supplied in an 8-pin PDIP package. The device combines four-channel 10-bit ADC capability, six I/O pins, a comparator, and a compact instruction set in a low-cost embedded-control package. A PIC microcontroller is a programmable integrated circuit that combines a CPU core, nonvolatile program memory, data memory, I/O ports, and peripherals on one chip. The PIC12F675 belongs to the 8-bit PIC12 low-pin-count family and is intended for small control systems that require more than simple logic but do not need a high-performance processor. Its Flash program memory permits in-circuit reprogramming and supports firmware updates without replacing the device. The verified product data identifies a 20 MHz device with 200 ns instruction execution and a 35-single-word instruction set. The PIC12F675-I/P is identified as an 8-bit, 8-pin device with four channels and a 10-bit ADC. Six I/O ports are listed in the verified comparison data. The PDIP package is suitable for through-hole prototyping, educational kits, industrial control modules, and applications where a larger package is easier to inspect or hand-solder than a fine-pitch surface-mount package. Compared with a basic 8-bit MCU, the integrated ADC enables analog measurement without an external converter. The four ADC channels can be used for sensors, potentiometers, battery monitoring, and simple control loops. The device is suited to compact embedded products where Flash reprogrammability, low pin count, and a straightforward programming model are more valuable than high processing bandwidth. Its CMOS construction and 8-pin integration reduce the number of external components in simple control boards. Typical applications include small sensor nodes, temperature controllers, fan controllers, LED sequencers, battery-powered instruments, hobby robotics, and basic industrial automation modules. The device can evaluate analog inputs, drive discrete outputs, and execute control logic from a single microcontroller. For designs requiring higher memory, more peripherals, or expanded communication, related PIC devices may be preferable. Designers should use the manufacturer pinout description and verify the 8-pin PDIP footprint, programming connections, oscillator configuration, and analog-input routing on the PCB. The A/D converter, comparator, and digital I/O share limited pins, so mixed analog and digital layouts require careful grounding and decoupling. Firmware must also account for the device's 8-bit architecture and limited peripheral resources. This page combines the verified manufacturer and distributor information with practical application guidance, comparison notes, and engineering-oriented caveats. It is intended to help engineers identify whether the PIC12F675-I/P fits an embedded-control design before downloading the official datasheet and planning a PCB layout.

RFQ যোগাযোগ
PIC12F675-I/SN - 8-Bit Flash MCU, 1.75KB, ADC, SOIC-8 | Microchip
PIC12F675-I/SN

PIC12F675-I/SN - 8-Bit Flash MCU, 1.75KB, ADC, SOIC-8 | Microchip

The Microchip Technology PIC12F675-I/SN is an 8-bit PIC® flash-based CMOS microcontroller in an 8-pin SOIC (SN) package, operating from 2.0V to 5.5V with up to 20 MHz clock speed. It integrates 1.75KB (1K x 14 words) of Flash program memory, 64 bytes of RAM, 128 bytes of EEPROM, a 10-bit ADC with 4 input channels, one comparator, and a dedicated 8-bit timer plus a 16-bit timer/counter. An MCU (microcontroller unit) is a single-chip computer containing a CPU, memory, and programmable I/O peripherals designed for embedded control. Within the broader semiconductor taxonomy, MCUs sit under microcontrollers -> embedded processors -> digital ICs -> semiconductors. The PIC12F675 belongs to Microchip's PIC12F family of low-pin-count (8-pin) MCUs, which are widely used in cost- and space-sensitive designs. Key differentiating features include the on-chip 10-bit A/D converter (the differentiating feature versus the otherwise-identical PIC12F629), an internal 4 MHz oscillator with software-selectable calibration, a watchdog timer with independent on-chip oscillator, in-circuit serial programming (ICSP), and an operating temperature range of -40C to +85C (industrial grade). The SOIC-8 package offers excellent PCB-handling characteristics and is compatible with hand-soldering as well as automated assembly. Architecturally, the device uses a RISC core with only 35 single-word instructions and a 200 ns instruction execution time at 20 MHz. Harvard bus architecture separates program and data paths, and the integrated EEPROM supports >1M erase/write cycles, while Flash endurance is rated for >100K cycles. The 6 GPIO pins each have independent weak pull-up control and interrupt-on-change capability. Typical applications include small sensor interface nodes, battery chargers, LED drivers, smoke detectors, fan controllers, and remote control transmitters. The combination of integrated ADC, comparator, and EEPROM in an 8-pin footprint is particularly attractive when board area and BOM cost are at a premium. When designing with this part, ensure decoupling capacitors are placed as close as possible to VDD/VSS and that the MCLR pin is tied properly to support ICSP. Operating voltage should be checked against peripheral requirements (ADC accuracy is specified at >=2.5V). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that complement, but do not replace, the manufacturer datasheet.

RFQ যোগাযোগ
PIC12F675T-E/SN - 8-Bit 20MHz MCU 1.75KB Flash SOIC8 | Microchip
PIC12F675T-E/SN

PIC12F675T-E/SN - 8-Bit 20MHz MCU 1.75KB Flash SOIC8 | Microchip

The Microchip Technology PIC12F675T-E/SN is an 8-bit CMOS Flash-based PIC microcontroller in an 8-pin SOIC (SN) package, designed for low-power embedded applications with extended temperature operation. It features a 20MHz maximum clock, 1.75KB (1K x14 words) of Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM data storage, plus a 10-bit 4-channel ADC. The 'T' suffix denotes Tape & Reel packaging for high-volume assembly, while 'E' indicates the extended -40C to +125C industrial operating temperature range. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, working RAM, peripherals, and I/O. PIC microcontrollers use a RISC (Reduced Instruction Set Computer) architecture, executing each instruction in a single cycle (200ns at 20MHz), enabling deterministic timing. The PIC12F family targets cost- and pin-constrained designs where 6-8 pins are sufficient. The 12F675 specifically adds a 10-bit ADC and on-chip EEPROM, distinguishing it from the lower-cost 12F629 sibling that lacks these features. Key features include 35 single-word instructions, only 8.5 uA operating current at 32 kHz and 100 uA at 1 MHz, a 1 nA typical standby current, an internal 4MHz/8MHz oscillator, and a wide 2.0V to 5.5V supply range. The device also integrates brown-out reset, power-on reset, watchdog timer, and an enhanced PWM module. These features make it ideal for battery-powered and energy-harvesting applications where quiescent current dominates total energy consumption. The architecture is built around a Harvard-style RISC core, separate program and data buses, and on-chip debug via ICD. The 10-bit ADC with 4 input channels can be used for sensor signal acquisition such as temperature, voltage, or current monitoring. The internal oscillator eliminates external crystal components in cost-sensitive layouts, while the industrial temperature grade allows deployment in uncontrolled environments. Typical applications include battery chargers, LED lighting controllers, sensor conditioning nodes, smoke and gas detectors, small appliance control, automotive body electronics, and IoT edge nodes. The combination of low power consumption, integrated peripherals, and small form factor also makes the part popular in retrofit industrial sensor modules. When designing with the PIC12F675T-E/SN, ensure decoupling capacitors of at least 0.1 uF are placed within 5mm of the VDD pin, and reserve one GPIO for the ICSP programming interface (PGD/PGC). For ADC accuracy, average multiple samples and use the internal voltage reference for ratios that are insensitive to absolute reference drift. This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F675T-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip
PIC12F675T-I/MD

PIC12F675T-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12F675T-I/MD is an 8-bit Flash-based CMOS microcontroller in the PIC12F family, packaged in an 8-lead DFN (4x4 mm, exposed pad) with tape and reel packaging. It integrates a 20 MHz core, 1.75 KB (1K x 14 words) of Flash program memory, 64 bytes of RAM, 128 bytes of EEPROM, a 10-bit ADC with 4 channels, and an on-chip 4 MHz internal oscillator. The device operates from 2.0V to 5.5V and features 6 general-purpose I/O pins. What is a Flash-based 8-bit microcontroller? An 8-bit microcontroller is a small computer-on-a-chip that processes data in 8-bit chunks and integrates CPU, memory (Flash for program storage, RAM for data, EEPROM for non-volatile data), peripherals (ADC, timers, communication), and I/O on a single die. Flash memory allows in-circuit reprogramming via ICSP, making these MCUs ideal for prototyping, low-volume production, and field-upgradable designs. PIC microcontrollers are widely used in cost-sensitive embedded applications due to their deterministic RISC architecture, low power consumption, and a 35-instruction set that simplifies firmware development. The PIC12F675 delivers 200 ns instruction execution, hardware UART, comparators, and an enhanced PWM module. Its nanopower technology provides low sleep current for battery-operated designs. The integrated 10-bit ADC with 4 channels eliminates external analog components in many sensing applications. Six GPIO pins support direct interfacing to sensors, switches, LEDs, and communication lines. The device also features a programmable brown-out reset (BOR), watchdog timer, and in-circuit serial programming (ICSP) for in-field firmware updates. The architecture is built on Microchip's enhanced mid-range 8-bit RISC core with a single accumulator and hardware multiplier support. The Harvard architecture separates program (Flash) and data (RAM) buses, allowing simultaneous instruction fetch and data access. The 14-bit wide instruction word reduces code density issues common with 12-bit PIC parts. The 10-bit ADC uses successive approximation with internal or external voltage reference selection. Typical applications include low-power sensor nodes, battery management, LED lighting controllers, automotive interior electronics, consumer appliance control, and small IoT edge devices. The wide operating voltage range supports direct connection to 2xAA/3xAA battery packs as well as regulated 3.3V and 5V rails. Designers benefit from Microchip's MPLAB X IDE and XC8 compiler ecosystem, which provide free development tools. When designing with the PIC12F675, ensure ICSP programming header access is preserved on the PCB. The internal 4 MHz oscillator eliminates the external crystal in many designs, but precision timing applications should still use an external resonator or crystal. Decoupling capacitors (100 nF plus bulk) must be placed close to VDD. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet, helping engineers select, source, and apply the PIC12F675T-I/MD with confidence.

RFQ যোগাযোগ
PIC12F675T-I/MF - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip
PIC12F675T-I/MF

PIC12F675T-I/MF - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

The Microchip Technology PIC12F675T-I/MF is an 8-bit CMOS Flash-based microcontroller in a PIC® 12F family architecture, delivering 20MHz (200 ns instruction execution) performance with 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM. Housed in an 8-pin DFN-S (6x5 mm) surface-mount package, the device integrates 6 I/O pins, a 4-channel 10-bit ADC, one comparator, and a hardware USART/SCI module, all operating from a 2.0V to 5.5V supply. The part is specified for the industrial temperature range of -40°C to +85°C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and configurable peripherals. The 8-bit MCU class, including the PIC12F family, is widely used in cost- and space-constrained applications that need deterministic real-time response rather than high computational throughput. PIC12F microcontrollers sit at the entry level of Microchip's 8-bit portfolio, prioritizing low pin count, low power, and ease of development with only 35 single-word instructions. Key features of the PIC12F675T-I/MF include 1.75KB self-programmable Flash, 128 bytes of EEPROM for non-volatile data storage, an internal 4MHz oscillator with software-selectable calibration, and a 10-bit ADC with 4 input channels that can also be used as digital I/O. The integrated comparator supports simple analog signal conditioning, while the USART/SCI module enables asynchronous serial communication with baud rates up to several hundred kbps. The device also provides an in-circuit serial programming (ICSP) interface that allows field firmware updates via two standard pins. Architecturally, the PIC12F675 uses a Harvard RISC core with a 14-bit instruction word, 8-bit data path, and a single accumulator (W register) that delivers predictable, deterministic instruction timing. The Flash memory uses a 14-bit word organization that maps to 1024 instruction words (1.75KB). The internal 4MHz oscillator and four available clock modes allow designers to balance active current consumption against execution speed, and the device supports both internal and external oscillator configurations for EMI-sensitive designs. Typical applications include battery-powered sensor nodes, consumer appliance control, LED driver controllers, simple state machines, and automotive accessory modules where AEC-Q100 grade variants (e.g., PIC12F675-I/MF in automotive screening) are acceptable. The small 8-pin DFN package is well suited for space-limited PCB designs such as remote keyless entry fobs, smart thermostats, and personal medical accessories. Designers should note that the DFN-8 (6x5 mm) exposed pad must be soldered to a sufficient copper area for thermal dissipation and electrical grounding. Decoupling capacitors of 100nF and 10µF should be placed within 3 mm of the VDD pin to ensure stable operation across the 2.0V to 5.5V supply range. For noise-sensitive ADC readings, AVSS should be tied directly to the ground plane, and the analog inputs should be guarded by digital traces. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC12F675T-I/SN - 8-Bit 20MHz CMOS Flash MCU, 1.75KB | Microchip
PIC12F675T-I/SN

PIC12F675T-I/SN - 8-Bit 20MHz CMOS Flash MCU, 1.75KB | Microchip

The Microchip Technology PIC12F675T-I/SN is an 8-bit RISC CMOS Flash-based microcontroller delivering 20 MHz (200 ns instruction cycle) performance from a 1.75 KB (1K x 14) Flash program memory and 64 bytes of RAM in an 8-pin SOIC package. It integrates a 4-channel 10-bit Analog-to-Digital Converter, one capture/compare/PWM module, and an internal 4 MHz oscillator with software-selectable calibration, enabling compact designs that minimize external component count. An 8-bit microcontroller is a microprocessor core that processes data 8 bits at a time and is optimized for embedded control tasks such as sensing, timing, and GPIO expansion. Within the broader semiconductor taxonomy, this PIC12F675 belongs to the 8-bit microcontroller family -> microcontroller unit (MCU) -> embedded processor -> integrated circuit. The PIC12F675 sits in Microchip's PIC12F mid-range architecture, the smallest-footprint sub-family of the PIC® mid-range line, designed for low-pin-count applications where PCB area, BOM count, and cost dominate the design trade-off. Key features include a 35-instruction RISC instruction set (single-cycle except branches), an 8-level deep hardware stack, interrupt capability, 6 digital I/O pins (5 GPIO + 1 input-only), an internal comparator with on-chip reference, and Flash program memory with self-programmability for in-field firmware upgrades. The 'T' suffix indicates Tape & Reel packaging and the 'I' suffix denotes the industrial temperature range of -40 °C to +85 °C. The device operates from 2.0 V to 5.5 V, supporting both 3.3 V and 5 V system rails. Technically, the PIC12F675 uses a Harvard architecture with separate program and data buses, allowing instruction fetch and operand read to occur in the same cycle. Its enhanced FLASH memory uses 14-bit-wide instructions, the wider word size enabling 35 opcodes that cover arithmetic, bit-manipulation, and peripheral control. The 10-bit ADC achieves a typical acquisition time suitable for slow-changing sensor signals such as thermistors, photocells, and battery monitors. Typical applications include low-power sensor nodes, automotive body electronics, industrial control loops, AC power measurement, smoke detectors, and any place a small analog/mixed-signal MCU is required. Pairing the internal ADC with the on-chip comparator makes it especially well-suited to battery chargers and threshold-detection circuits. When designing with this part, ensure decoupling capacitors are placed within 5 mm of VDD, route the MCLR pin through a 10 kΩ pull-up for reliable reset, and budget Flash endurance at 100K erase/write cycles per the manufacturer datasheet. This page synthesizes distributor pricing, drop-in alternatives within the PIC12F family, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F683-E/MD - 8-Bit 20MHz MCU 3.5KB Flash 8-DFN | Microchip
PIC12F683-E/MD

PIC12F683-E/MD - 8-Bit 20MHz MCU 3.5KB Flash 8-DFN | Microchip

The Microchip Technology PIC12F683-E/MD is an 8-bit PIC12 family CMOS flash microcontroller delivering 20 MHz instruction throughput (200 ns instruction cycle) with 3.5 KB (2K x 14) of Flash program memory, 128 bytes SRAM, and 256 bytes of EEPROM, housed in a compact 8-pin DFN (4x4 mm) package. It integrates a 4-channel 10-bit ADC, two 8-bit timers plus one 16-bit timer, a 4-channel hardware PWM module, an enhanced USART, and an internal 8 MHz precision oscillator selectable via software across 31 kHz to 8 MHz. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU core, program memory (Flash/ROM), data memory (SRAM), non-volatile EEPROM, and a fixed set of peripherals onto one die. PIC12F microcontrollers sit within Microchip's mid-range 14-bit instruction architecture hierarchy, which itself belongs to the broader PIC family of RISC microcontrollers (PIC -> PIC10/12/16/18 -> PIC12F low-pin-count subfamily). The PIC12F683 specifically targets space-constrained designs that still require analog sensing and PWM control, blending digital I/O with a precision 10-bit ADC on a minimal 8-pin footprint. Key features of the PIC12F683-E/MD include an operating voltage range of 2.0 V to 5.5 V, industrial extended temperature range of -40 °C to +125 °C, low-power nanoWatt technology with typical sleep current under 1 µA, and a configurable 8 MHz internal oscillator that eliminates the need for an external crystal in most designs. Its 4-channel 10-bit ADC supports both standard and high-speed conversions, while the enhanced capture/compare/PWM (ECCP) module drives MOSFETs, LEDs, or motor phases directly from the GPIO pins. The architecture uses a 14-bit wide instruction word, 8-level hardware stack, and 35 single-word instructions, simplifying firmware development. The /MD suffix indicates a 4x4 mm DFN surface-mount package, the most compact option in the PIC12F683 family, while the -E prefix indicates the extended -40 °C to +125 °C industrial temperature range. Code protection, a 1k erase/program cycle endurance rating on Flash, and 100k cycle endurance on EEPROM make it suitable for field-deployed embedded nodes. Typical applications include battery chargers, LED lighting controllers, fan speed regulators, small sensor signal conditioners, and low-cost consumer appliance controls. Its tiny DFN-8 footprint and integrated peripherals make it ideal for designs where PCB area is at a premium. When designing with this device, reserve adequate copper area for the exposed pad thermal dissipation and follow Microchip's recommended decoupling network (100 nF plus 10 µF bulk) within 5 mm of the VDD pin. This page combines distributor stock and pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F683-E/P - 8-bit 20MHz 3.5KB Flash MCU | Microchip
PIC12F683-E/P

PIC12F683-E/P - 8-bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip PIC12F683-E/P is an 8-bit Flash-based CMOS microcontroller built on Microchip's mid-range 14-bit instruction set architecture, offered in an 8-pin PDIP through-hole package. The device integrates 3.5 KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM data memory, with a maximum CPU clock of 20 MHz derived from the internal oscillator or an external crystal. It operates across an extended industrial temperature range (-40C to +125C), as indicated by the -E (extended) suffix, with a supply voltage range of 2.0 V to 5.5 V. An 8-bit microcontroller (MCU) is a small single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), volatile working memory (RAM), non-volatile data memory (EEPROM), and a set of programmable I/O pins on a single silicon die. 8-bit MCUs sit at the entry level of the embedded computing hierarchy (8-bit -> 16-bit -> 32-bit MCU -> microprocessor -> SoC) and remain dominant where cost, simplicity, and deterministic real-time response matter more than raw throughput. The PIC12F683 is the highest-spec member of Microchip's 8-pin PIC12F family and adds peripherals absent on smaller cousins such as the PIC12F508/509. Key features include a 4-channel 10-bit Analog-to-Digital Converter (ADC), one Enhanced Capture/Compare/PWM (ECCP) module, one Capture/Compare/PWM (CCP) module, four 8-bit timers plus one 16-bit timer, an internal 8 MHz precision oscillator, a comparator module, and nanoWatt power-management modes for low-power battery applications. Six general-purpose I/O pins are available, all capable of interrupt-on-change wake-up. The -E temperature grade and PDIP-8 form factor make this part particularly well suited to prototyping, hobby projects, and through-hole industrial designs that must survive harsh thermal environments. The PIC12F683 architecture is built on a 14-bit-wide instruction word with single-cycle execution on most instructions (except branches), giving 200 ns instruction time at 20 MHz. Internal peripherals are mapped into a unified data-memory SRAM area and configured through Special Function Registers (SFRs). The nanoWatt technology provides multiple idle and sleep modes that can reduce quiescent current to the sub-microamp range, enabling years of operation from a coin cell. Typical applications include LED lighting control, battery chargers, sensor signal conditioning, low-power remote controls, smoke detectors, and small appliance motor control. The integrated ADC and PWM peripherals allow direct interface to analog sensors and MOSFET/IGBT gate drivers without external analog circuitry, reducing bill-of-materials cost and PCB area. When designing with the PIC12F683, ensure that MCLR is pulled high through a 10 kohm resistor and that the ICSP programming header is accessible for field updates. Designers migrating from older PIC12F parts should review the ECCP initialization sequence, which differs from the CCP modules on legacy devices. This page synthesizes verified distributor pricing, drop-in 8-pin PDIP alternatives from the PIC12F family, and practical design notes not consolidated on the manufacturer datasheet.

RFQ যোগাযোগ
PIC12F683-I/MD - 8-bit 20MHz MCU 3.5KB Flash 6 I/O | Microchip
PIC12F683-I/MD

PIC12F683-I/MD - 8-bit 20MHz MCU 3.5KB Flash 6 I/O | Microchip

The Microchip Technology PIC12F683-I/MD is an 8-bit PIC microcontroller featuring a mid-range x14 RISC architecture, 3.5KB (2K x 14) of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM data memory. The part operates up to 20 MHz instruction clock and integrates a 4-channel 10-bit ADC, a precision internal oscillator, and a nanoWatt power-saving mode set, packaged in an 8-pin DFN (4x4 mm) with an exposed pad. Background: An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for embedded control tasks such as sensor reading, simple actuation, glue logic, and protocol conversion. Microchip's PIC12 family targets ultra-low-pin-count applications (8 pins) where PCB real estate is constrained. Within the broader taxonomy, the PIC12F683 belongs to: microcontroller -> 8-bit MCU -> mid-range PIC architecture -> flash-based programmable MCU -> embedded computing IC. Key features include a wide operating voltage range of 2.0V to 5.5V, six general-purpose I/O pins with interrupt-on-change capability, an internal 8 MHz oscillator (calibrated to ±1% across Vdd and temperature), one Enhanced Capture/Compare/PWM (ECCP) module, one comparator, and nanoWatt sleep modes that drop quiescent current to the microamp range for battery-powered designs. Technically, the PIC12F683 executes one instruction per clock cycle (200 ns at 20 MHz) using the 14-bit instruction word, giving deterministic timing for control loops. The device is supported by the MPLAB X IDE and the XC8 C compiler, enabling C-based firmware development alongside assembly. The integrated 10-bit ADC samples up to four analog channels, while the ECCP and PWM peripherals support motor, LED, and signal-conditioning topologies without external circuitry. Typical applications include battery-powered sensor nodes, IR remote controls, simple LED drivers, capacitive-touch interface replacements, and auxiliary housekeeping logic on larger boards. The 8-pin DFN footprint (~9 mm² of board area) is significantly smaller than SOIC-18 alternatives, enabling miniaturized products such as wearables, IoT edge nodes, and disposable medical indicators. When designing with this part, allocate the exposed pad (EP) as a thermal and ground bond; route ground and decoupling to it on the top layer. Verify Vdd decoupling with a 0.1 µF ceramic placed within 5 mm of the supply pin, and ensure in-system serial programming (ICSP) pads are accessible for production flashing. This page synthesizes distributor pricing, drop-in PIC12 family alternatives, and practical layout notes for compact PCB designs - content not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F683-I/P - 8-Bit 20MHz MCU 3.5KB Flash | Microchip
PIC12F683-I/P

PIC12F683-I/P - 8-Bit 20MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12F683-I/P is an 8-bit Flash-based CMOS microcontroller in the PIC12 mid-range family, delivering 20MHz CPU performance with 3.5KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM data memory, all housed in a through-hole 8-pin PDIP package. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, memory, and peripherals into a single IC. The PIC12F683 belongs to Microchip's mid-range x14 architecture family, positioned in the broader hierarchy of microcontroller -> embedded controller -> semiconductor device. It is widely used as a compact glue-logic replacement, sensor-interface controller, and low-power autonomous subsystem in cost-sensitive designs. Key features include a 4-channel 10-bit ADC with internal voltage reference, one 8-bit and one 16-bit timer, enhanced PWM/capture/compare module, a comparator with programmable on-chip reference, and nanoWatt Technology power management for ultra-low sleep currents below 1 µA typical. The device supports In-Circuit Serial Programming (ICSP) via two pins, allowing firmware updates after PCB assembly. The PIC12F683-I/P operates from 2.0V to 5.5V and offers six general-purpose I/O pins with individual direction control and weak pull-ups. Its mid-range instruction set provides 35 single-word instructions, all single-cycle except branches. This combination of integrated peripherals, small footprint, and proven toolchain support (MPLAB X IDE, XC8 compiler) makes the part popular for hobbyist and industrial applications. Typical applications include LED drivers, sensor signal conditioning, battery chargers, simple motor control, and consumer appliance user-interface modules. Its internal 8MHz oscillator and on-chip peripherals minimize external component count, enabling two-layer through-hole designs. When designing with the PIC12F683-I/P, plan for ICSP header access even on prototypes - the ICSP pins (GP0/GP1) are multiplexed with the serial interface. Decouple VDD with a 100nF ceramic capacitor placed within 5mm of the package, and reserve an area for an optional 32.768kHz crystal on GP4/GP5 if low-power RTCC operation is needed. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC12F683-I/SN - 8-bit 20MHz 3.5KB Flash MCU | Microchip
PIC12F683-I/SN

PIC12F683-I/SN - 8-bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12F683-I/SN is an 8-bit Flash-based CMOS microcontroller in an 8-pin SOIC package, featuring a 20 MHz maximum CPU clock, 3.5 KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM data memory. Built on Microchip's mid-range 14-bit instruction set architecture, it integrates a 4-channel 10-bit ADC, one 8-bit and one 16-bit timer, a capture/compare/PWM (CCP) module, and an enhanced USART. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, RAM, and configurable peripherals. The PIC12F683 belongs to the low-pin-count (8-pin) Flash MCU family, a sub-category of 8-bit microcontrollers targeted at cost- and size-sensitive embedded designs where only a handful of I/O lines are needed but on-chip analog and timing peripherals are still required. Key features of this device include a wide 2.0 V to 5.5 V operating voltage range, ultra-low-power nanoWatt technology with standby current of approximately 50 nA, and operating currents of roughly 11 µA at 32 kHz and 220 µA at 4 MHz. It also provides six independently configurable bidirectional I/O pins, an internal 8 MHz oscillator with software calibration, and an integrated analog comparator. The 'I' suffix designates the industrial temperature grade of -40 °C to +85 °C, while '/SN' denotes the 8-pin SOIC package. Typical applications for the PIC12F683-I/SN include battery-powered sensor nodes, LED lighting controllers, simple motor and fan control loops, consumer remote controls, and small home appliances. The combination of nanoWatt sleep modes and on-chip peripherals makes it well suited for designs that must run for years on a single coin-cell battery. When designing with this part, choose the appropriate internal or external oscillator configuration early in the firmware planning stage and budget Flash and RAM carefully against the 2K x 14 program word limit and 128-byte data SRAM. Decoupling the VDD pin with a 0.1 µF ceramic capacitor placed within a few millimeters of the device is strongly recommended. This page synthesizes distributor pricing, drop-in SOIC-8 alternatives from the same PIC12F family, and practical design notes not found in the manufacturer datasheet, helping engineers select and source the right PIC12F variant for cost-sensitive, low-pin-count embedded designs.

RFQ যোগাযোগ
PIC12F683T-E/MF - 8-Bit 20MHz 3.5KB Flash MCU | Microchip
PIC12F683T-E/MF

PIC12F683T-E/MF - 8-Bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC12F683T-E/MF is an 8-bit PIC® RISC flash microcontroller running up to 20 MHz instruction rate, packaged in an 8-pin DFN-S EP (6x5 mm) with exposed thermal pad and shipped on tape-and-reel. The PIC12F683T-E/MF integrates 3.5 KB (2K x 14) of self-programmable flash program memory, 256 bytes of EEPROM data memory, and 128 bytes of SRAM on a mid-range 14-bit instruction core that executes most instructions in 200 ns. Four 10-bit ADC channels, one enhanced capture/compare/PWM (ECCP) module, and an internal 8 MHz / 31 kHz oscillator cluster make it a complete SoC in 8 pins. A microcontroller (MCU) is a single-chip computer that combines a CPU, program and data memory, peripherals, and I/O on one die. The PIC12F683 belongs to the mid-range PIC12 family, part of the broader 8-bit PIC microcontroller architecture that evolved from the original Harvard-design PIC1650. Within Microchip's portfolio, the PIC12 sub-family targets low-pin-count, cost-sensitive embedded designs that still need on-chip EEPROM, ADC, and PWM. The 'F' denotes flash program memory, which allows in-circuit re-programming for field upgrades and development iteration. Key features of the PIC12F683 include 5 or 6 general-purpose I/O pins (depending on oscillator selection), four 10-bit ADC channels with internal 1.024V / 2.048V / 4.096V voltage references selectable via the FVRCON register, a 16-bit ECCP module for motor/PWM control, hardware USART, an SR-latch, comparator module with absolute voltage reference, and the nanoWatt power-managed modes that drop standby current to ~50 nA typical. Watchdog timer with on-chip RC oscillator, brown-out reset, and low-voltage programming are all standard. Operating from 2.0 V to 5.5 V across -40 °C to +125 °C (E = extended temperature), the PIC12F683 is built on a CMOS process optimized for low static current and wide supply tolerance. The enhanced mid-range core extends the instruction set to 35 single-word instructions while preserving pin and code compatibility with legacy PIC12 and PIC16 devices, which eases migration. The DFN-S package (also called 8-VDFN exposed-pad) measures 6 x 5 mm and provides a low thermal-resistance path to PCB copper, supporting the industrial temperature range without an explicit heatsink. Typical applications include low-pin-count consumer and industrial sensor conditioning, LED lighting drivers, battery chargers, motor control loops for small DC fans and pumps, remote-keyless entry (RKE) transmitters, and home-automation nodes. The 4x10-bit ADC and 16-bit PWM together suit closed-loop tasks such as PID-controlled solenoid drive or constant-current LED dimming. Internal oscillator options (INTOSC 31 kHz to 8 MHz with PLL) eliminate external crystals, reducing BOM cost in price-sensitive designs. A key design consideration is the DFN exposed-pad layout: the central EP must be soldered to a thermal pad tied to ground to meet the datasheet thermal envelope. Engineers should also verify that the oscillator selection bit configuration leaves at least four usable I/O pins; with the 8 MHz INTOSC selected, GP5 becomes an oscillator pin and only five GPIOs remain. Programming is supported by Microchip's MPLAB X IDE and the XC8 compiler at no charge. This page consolidates drop-in DFN alternatives, distributor pricing as of 2026-09-15, and design notes beyond the Microchip datasheet summary to help engineers shorten the PIC12F683T-E/MF selection cycle.

RFQ যোগাযোগ