মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC16C55A-04/P - 8-Bit 4MHz OTP MCU 20 I/O | Microchip
PIC16C55A-04/P

PIC16C55A-04/P - 8-Bit 4MHz OTP MCU 20 I/O | Microchip

The Microchip PIC16C55A-04/P is an 8-bit RISC microcontroller from the PIC16C5X family, featuring 4MHz maximum clock speed, 768 bytes (512 x 12) of One-Time-Programmable (OTP) program memory, 24 bytes of RAM, and 20 digital I/O pins in a 28-pin PDIP (Plastic DIP) through-hole package. The -04 speed suffix denotes a 4MHz oscillator range, and the /P suffix denotes the PDIP package. A microcontroller (MCU) is a single-chip computer containing a processor core, memory, and programmable I/O peripherals, used in embedded applications where a full microprocessor would be too costly or power-hungry. The PIC16C5X family employs a RISC architecture with 33 single-word/single-cycle instructions, achieving 2:1 code compression over competitive 8-bit MCUs in its class, and uses 12-bit-wide instructions with an 8-bit-wide data path. Key features include seven or eight special-function hardware registers, a two-level-deep hardware stack, direct/indirect/relative addressing modes for data and instructions, an 8-bit real-time clock/counter (TMR0), and supply-voltage operation of 3.0V to 6.25V. The 20 I/O pins each support independent direction control, and the OTP program memory is programmed via Microchip's MPLAB PM3 Universal Device Programmer. The PIC16C5X architecture is fully static CMOS, meaning the clock can be stopped without losing register state - useful for low-power applications. Two instruction-fetch methods (call/branch timing variations) are supported. Power-on reset and watchdog timer peripherals are integrated, and the chip operates over the standard 0C to +70C commercial temperature range (industrial variants use the -I suffix). Typical applications include appliance controllers, simple sensor interfaces, hobby/educational projects, replacement of discrete logic, automotive interior modules, and any low-cost high-volume embedded design requiring 20 or fewer I/O pins. The OTP memory is well-suited for production designs where program stability has been finalized. When designing with this device, note that the PIC16C5X has no on-chip debug and requires a separate programmer - migrate to PIC16F5X or PIC16F core devices with Flash memory and ICSP for new designs that require in-circuit programming. Decoupling capacitors (0.1uF ceramic near VDD) and a clean reset circuit are essential for reliable operation. This page synthesizes distributor pricing, drop-in alternatives, and design considerations not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55A-04/SO - 8-Bit 4MHz OTP MCU 768B | Microchip | SOIC-28
PIC16C55A-04/SO

PIC16C55A-04/SO - 8-Bit 4MHz OTP MCU 768B | Microchip | SOIC-28

The Microchip Technology PIC16C55A-04/SO is an 8-bit RISC microcontroller from the PIC16C5x family, featuring a 4 MHz maximum clock, 768 bytes (512 x 12) of One-Time-Programmable (OTP) program memory, and 24 bytes of RAM, all housed in a 28-pin SOIC package. It executes instructions using a reduced RISC architecture with only 33 single-word/single-cycle instructions, enabling deterministic throughput for embedded control. The OTP memory makes it ideal for volume production where firmware is finalized and unit cost matters more than field reprogrammability. An 8-bit microcontroller (MCU) is a single-chip computer integrating a CPU, RAM, program memory (ROM/EPROM/Flash/OTP), and peripherals such as I/O ports, timers, and communication interfaces on one die. Within the broader power management and embedded hierarchy, MCUs sit alongside DSPs, FPGAs, and microprocessors as programmable logic devices. The PIC16C5x family occupies the low-cost, high-performance niche for cost-sensitive appliance, automotive accessory, and industrial sensor applications. Key features of the PIC16C55A-04/SO include 20 digital I/O pins, a 12-bit instruction word with 8-bit data path, an operating voltage range of 3.0V to 6.25V, and CMOS fully-static design that allows clock rates down to DC for low-power standby. The 4 MHz version (the "/04" suffix) targets applications where 1 microsecond instruction execution is sufficient. It supports in-circuit serial programming via Microchip's legacy tools and provides power-on reset and watchdog timer functionality in the baseline PIC16C5x feature set. Architecturally, the PIC16C55A uses a Harvard memory layout with separate program and data buses, a 2-level hardware stack, and direct/indirect addressing modes. The device is fabricated on a CMOS process optimized for low quiescent current, and its 4 MHz speed grade is the most common production variant. According to Microchip's documentation, the PIC16C5x series is the foundation on which later PIC16 and PIC18 architectures were developed. Typical applications include appliance control boards, LED display drivers, simple sensor interfaces, remote controls, and low-cost industrial timers. Its wide 3.0V-6.25V supply range also makes it compatible with legacy 5V logic designs and unregulated supplies in cost-optimized products. When designing with this part, note that the OTP memory cannot be erased - code must be verified before programming. Engineers should reserve engineering samples for development and use windowed ceramic or Flash-based PIC16F parts during prototyping before locking in the OTP variant for production. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, including guidance on migrating from the C variant to the lower-cost F (Flash) versions.

RFQ যোগাযোগ
PIC16C55A-04/SP - 8-bit OTP MCU, 768B, 20 I/O | Microchip
PIC16C55A-04/SP

PIC16C55A-04/SP - 8-bit OTP MCU, 768B, 20 I/O | Microchip

The Microchip Technology PIC16C55A-04/SP is an 8-bit RISC microcontroller from the PIC16C5x baseline family, delivering 4 MHz CPU performance with 768 bytes of One-Time-Programmable (OTP) program memory organized as 512 x 12-bit words. Housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package, this industrial-temperature-rated MCU exposes 20 digital I/O pins, 24 bytes of data RAM, and a single 8-bit timer/counter (TMR0). Its 12-bit instruction word and 2:1 code compression deliver a RISC instruction set that fits more functionality into a smaller memory footprint than competing 8-bit architectures. A baseline PIC microcontroller is a member of Microchip's PIC16C5x family — a family of 8-bit Harvard-architecture RISC microcontrollers built around a 12-bit program word, 8-bit data path, and a small register file. Within the broader taxonomy, a PIC baseline MCU is a microcontroller (MCU) — a single-chip processor integrating core, non-volatile program memory, RAM, I/O, and timers — which itself is a sub-category of embedded microcontrollers and ultimately of integrated circuits for embedded control. The PIC16C5x baseline family targets cost-sensitive, deterministic, interrupt-free control loops where predictability and small code size outweigh the need for analog peripherals or large RAM. Key features of the PIC16C55A-04/SP include: a two-level deep hardware stack for subroutine nesting, direct/indirect/relative addressing modes for compact pointer arithmetic, 8-bit real-time clock/counter (TMR0) with software-programmable prescaler, and a wide 2.5 V to 6.25 V operating voltage range. The device is specified over the commercial 0°C to +70°C temperature range, supports an external oscillator or RC clock source, and offers brown-out protection variants across the broader PIC16C5x family. The '04' speed suffix denotes the 4 MHz maximum oscillator grade. Typical applications for the PIC16C55A-04/SP include consumer appliance control, low-end toys and education, simple sensor signal conditioning, replacement of discrete logic in glue-controller roles, and white-goods timer/sequencer boards. The 20-pin-equivalent of GPIO and small code footprint also make it a popular choice for learning and hobbyist platforms that emulate older PIC16C5x development kits. When designing with the PIC16C55A-04/SP, observe that OTP memory requires masked-programmer flow at production time — engineering builds typically use a windowed (JW) or UV-erasable variant for iteration. Pin compatibility with the PIC16C54 and PIC16C56 families enables a single PCB layout to support several memory-density options across the product line. This page synthesizes distributor stock and pricing, drop-in PIC16C5x pin-compatible alternatives, and practical design notes not present in the bare Microchip datasheet, providing an engineering decision aid rather than a re-statement of specifications.

RFQ যোগাযোগ
PIC16C55A-04/SS - 8-Bit 4MHz OTP MCU 0.75KB SSOP-28 | Microchip
PIC16C55A-04/SS

PIC16C55A-04/SS - 8-Bit 4MHz OTP MCU 0.75KB SSOP-28 | Microchip

The Microchip Technology PIC16C55A-04/SS is an 8-bit EPROM/ROM-based CMOS microcontroller from the PIC16C5X family, operating at up to 4 MHz with 768 bytes (512 x 12) of One-Time-Programmable (OTP) program memory, 24 bytes of data RAM, and 20 digital I/O pins in a 28-pin SSOP (Shrink Small Outline Package). It uses a RISC architecture with 33 single-word, single-cycle instructions, a 12-bit instruction width with an 8-bit data path, and a two-level hardware stack. The "-04" speed grade specifies a 4 MHz maximum oscillator frequency, while the "A" suffix denotes the silicon revision with improved electrical characteristics over the original PIC16C55. An 8-bit OTP microcontroller is a single-chip computer that integrates CPU, non-volatile program memory (programmable once and not erasable in OTP variants), RAM, and peripheral I/O on one die. It belongs to the microcontroller hierarchy: microcontroller -> embedded MCU -> 8-bit MCU -> PIC16C5X family -> PIC16C55A derivative. OTP devices are favored in cost-sensitive, high-volume production where firmware is stable and in-system reprogrammability is unnecessary, offering lower per-unit cost than flash equivalents. Key features include seven or eight special-function hardware registers, an 8-bit real-time clock/counter (TMR0) with programmable prescaler, direct/indirect/relative addressing modes for both data and instructions, an internal power-on reset, a watchdog timer with on-chip RC oscillator, power-saving SLEEP mode, and selectable oscillator options (RC, XT, HS, LP). The device operates from 2.5 V to 6.25 V across commercial 0C to +70C temperature range. Typical applications include appliance control, electronic toys, automotive sub-systems (body controllers, lighting), industrial timers and counters, security-system keypads, low-end remote controls, smart sensors, and consumer white-goods. The 20 I/O pins easily drive LED arrays, key-scan matrices, character LCDs (via external driver), and discrete logic interfaces. The wide 2.5-6.25 V supply range permits direct battery operation from 3 V coin cells, two AA cells, or regulated 5 V rails. When designing with PIC16C55A-04/SS, allocate the oscillator and decoupling capacitors adjacent to the device, and observe the 4 MHz oscillator ceiling. Because the program memory is OTP, code must be fully validated on a windowed (PIC16C55A/JW) or FLASH prototype (PIC16F equivalent) before committing to OTP volume production. Use the PICSTART Plus or MPLAB PM3 programmer for device programming.

RFQ যোগাযোগ
PIC16C55A-04E/P - 8-Bit 4MHz OTP MCU, 768B, 28-PDIP | Microchip
PIC16C55A-04E/P

PIC16C55A-04E/P - 8-Bit 4MHz OTP MCU, 768B, 28-PDIP | Microchip

The Microchip Technology PIC16C55A-04E/P is an 8-bit EPROM-based microcontroller belonging to the PIC16C5X family, delivering 4 MHz maximum clock speed in a 28-pin PDIP (Plastic Dual In-line Package) through-hole form factor. The device integrates 768 bytes of program memory organized as 512 x 12 words and 25 bytes of data RAM, with 20 digital I/O lines arranged across ports A, B and C. It is offered in the automotive / extended temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and programmable I/O peripherals. The PIC16C5X family from Microchip is a classic baseline architecture employing a RISC instruction set with only 33 single-word, single-cycle instructions, achieving 2:1 code compression over competitive 8-bit microcontrollers in the same cost tier. Positioned within the broader semiconductor hierarchy, this device sits below modern PIC16 enhanced mid-range and PIC18 high-performance cores, but remains in production for long-life industrial and automotive designs that were qualified against the original PIC16C5X silicon. Key features include 4 MHz operating frequency, 12-bit wide instruction words, an 8-bit data path, a programmable watchdog timer, power-on reset, and a programmable code-protection bit. The OTP (One-Time Programmable) EPROM cell technology allows the firmware to be written once and locked permanently, which simplifies production programming and protects intellectual property. I/O current sourcing and sinking capabilities are sufficient to drive LEDs and small relays directly without external buffers in many designs. The PIC16C55A-04E architecture uses a Harvard-style separate program and data bus, single-cycle instruction fetch with two-stage pipelining, and a 2-level hardware stack that limits subroutine nesting depth. Compared with PIC16 enhanced cores, this baseline family lacks interrupts, so all real-time servicing must be performed via polled software loops - a key trade-off that benefits cost-sensitive applications where deterministic polling is acceptable. The 'E' suffix indicates the extended temperature grade (typically -40C to +125C), and 'P' designates the PDIP-28 package with through-hole leads. Typical applications include automotive body controllers, industrial appliance control, simple sensor interfaces, LED driver controllers, and replacement of discrete logic in legacy equipment. The wide operating temperature range supports under-hood automotive modules and outdoor industrial enclosures where commercial-grade parts would fail. When designing with this part, observe the maximum clock-versus-voltage constraint: at 5V VDD the device operates up to 4 MHz, while at lower supply voltages the maximum frequency decreases proportionally. Decouple VDD with a 0.1 uF ceramic capacitor placed close to the pin, and reserve the MCLR pin for a proper reset network unless it is disabled in configuration. This page synthesizes distributor pricing, cross-reference alternatives, and practical engineering notes that complement the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55A-04E/SP - 4MHz 8-Bit OTP MCU 768B | Microchip
PIC16C55A-04E/SP

PIC16C55A-04E/SP - 4MHz 8-Bit OTP MCU 768B | Microchip

The Microchip Technology PIC16C55A-04E/SP is an 8-bit RISC microcontroller belonging to the PIC16C5X baseline family, housed in a 28-pin SPDIP (SP) package. It operates at up to 4 MHz clock speed, delivers 768 bytes (512 x 12) of One-Time Programmable (OTP) program memory, 25 bytes of RAM, and 20 general-purpose digital I/O pins. The device supports the industry-standard 12-bit instruction word used across the PIC16C5X family, achieving a 2:1 code compression advantage over competitive 8-bit MCUs in its class. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, I/O peripherals, and often analog blocks into one package. The PIC16C5X belongs to the RISC (Reduced Instruction Set Computer) architecture lineage, designed for deterministic execution and low parts count in embedded designs. Within the broader taxonomy, this part sits as: microcontroller -> embedded controller -> semiconductor IC -> integrated circuit. Its baseline (12-bit instruction) architecture distinguishes it from mid-range (14-bit) and enhanced (16-bit) PIC families. Key features of the PIC16C55A include a 4 MHz maximum oscillator frequency, 2.0V to 6.25V operating voltage range (suitable for both 3.3V and 5V rails as noted in distributor datasheets), 20 digital I/O pins, a watchdog timer for code-flow safety, and an internal reset circuit. The 28-SPDIP package is the original through-hole form factor preferred for prototyping, hobbyist designs, and legacy industrial controllers where socketed or hand-soldered assembly remains common. Technically, the PIC16C55A uses a Harvard architecture with separated program and data paths, two-stack-level subroutine nesting, and a hardware-friendly instruction set optimized for C and assembly code density. The OTP memory supports one-time field programming for production volumes, with the -04E speed designation indicating the 4 MHz extended temperature grade suitable for industrial environments. Typical applications include legacy industrial control, appliance controllers, simple sensor interfaces, hobbyist and educational projects, and replacement of older discrete logic glue circuits. The wide voltage tolerance and deterministic interrupt handling also make it attractive for cost-sensitive automotive subsystems and standalone sensor readers. When designing with the PIC16C55A, remember that OTP memory cannot be rewritten, so code must be fully verified before final programming. The 28-SPDIP footprint is compatible with standard IC sockets and breadboards, simplifying field service and rapid iteration. For new designs consider PIC16F equivalents for Flash-based reprogrammability. This page synthesizes verified distributor pricing, parametric comparison tables, and same-package drop-in alternatives not found in the bare manufacturer datasheet, plus practical engineering notes for engineers evaluating the PIC16C55A-04E/SP.

RFQ যোগাযোগ
PIC16C55A-04E/SS - 8-Bit 4MHz OTP MCU 768B | Microchip
PIC16C55A-04E/SS

PIC16C55A-04E/SS - 8-Bit 4MHz OTP MCU 768B | Microchip

The Microchip Technology PIC16C55A-04E/SS is an 8-bit PIC® 16C-family microcontroller built on a fully-static CMOS process with One-Time Programmable (OTP) EPROM program memory, delivering 4 MHz maximum operating frequency, 768 bytes (512 x 12 words) of OTP program memory, and 24 bytes of RAM, housed in a 28-pin SSOP (Shrink Small Outline Package). It is part of the original PIC16C5X baseline architecture employing a RISC instruction set with 33 single-word/single-cycle instructions, two-level hardware stack, and direct/indirect/relative addressing modes. An 8-bit OTP microcontroller is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripherals into one package; the program memory can be written exactly once (One-Time Programmable), making these devices economical for low-to-medium-volume production. Within the broader taxonomy, the PIC16C55A sits at the bottom of the PIC16 family hierarchy: microcontroller -> 8-bit MCU -> PIC16 -> PIC16C5X baseline -> PIC16C55A. This hierarchy places it below PIC16C6X mid-range and PIC16C7X enhanced devices, and well below modern 16-bit dsPIC and 32-bit PIC32 offerings, but it remains a cost-effective solution for simple control tasks. Key features of the PIC16C55A-04E/SS include a 4 MHz operating frequency (4 MHz speed grade, denoted by the -04 suffix), 20 digital I/O pins organized across PORTA and PORTB, an 8-bit real-time clock/counter (TMR0) with 8-bit prescaler, watchdog timer with dedicated on-chip RC oscillator for reliable operation, power-on reset, power-saving SLEEP mode, and EPROM/ROM-based code storage. The device operates across the standard PIC16C5X voltage range and supports commercial and industrial temperature grades depending on the part suffix. The architecture uses a Harvard-style separate program and data bus, allowing instruction fetch and operand read to occur in the same cycle - a key reason the PIC16C5X delivers close to 1 MIPS per MHz. The 12-bit wide instruction word gives 2:1 code compression over typical 8-bit CISC microcontrollers of its class, enabling 512 instruction words to address relatively complex control sequences despite the small 768-byte program memory budget. Typical applications include low-cost appliance control, LED lighting controllers, simple sensor interfaces, battery chargers, remote control transmitters, automotive body controllers (with proper AEC-Q100 selection), and hobbyist/educational development platforms. The 20 I/O count makes it suitable for designs requiring multiple switches, relays, or LED indicators. When designing with the PIC16C55A-04E/SS, note that OTP memory cannot be erased or rewritten - use PIC16F55X or PIC16C55A JW-windowed parts for prototyping. Decoupling VDD with a 0.1 uF ceramic capacitor close to the pin is mandatory for stable oscillator operation; the MCLR pin must be tied to VDD through a resistor for normal operation. This page synthesizes distributor pricing for the PIC16C55A-04E/SS, current lifecycle status from Microchip, same-family drop-in alternatives including -04 and -04I speed/temperature variants, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55A-04I/P - 4MHz 8-Bit OTP MCU, 768B, 28-PDIP | Microchip
PIC16C55A-04I/P

PIC16C55A-04I/P - 4MHz 8-Bit OTP MCU, 768B, 28-PDIP | Microchip

The Microchip Technology PIC16C55A-04I/P is an 8-bit RISC microcontroller from the PIC16C5x family, featuring a 4 MHz maximum clock speed, 768 bytes of One-Time Programmable (OTP) program memory organized as 512 x 12 words, 24 bytes of RAM, and a 12-bit instruction word in a 28-pin PDIP through-hole package with industrial temperature grade (-40C to +85C). An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripheral I/O on one die. In the component taxonomy, an MCU belongs to the broader class of microcontrollers -> embedded processors -> digital ICs -> semiconductors. The PIC16C5x family pioneered Microchip's RISC architecture for low-cost, high-volume embedded control, and it is the direct ancestor of today's PIC16 and PIC18 families. Key features of the PIC16C55A-04I/P include 33 single-word single-cycle RISC instructions providing 2:1 code compression over CISC 8-bit MCUs of its era, a two-level deep hardware stack, an 8-bit real-time counter (TMR0) with an 8-bit programmable prescaler, direct/indirect/relative addressing, and seven or eight special function hardware registers. The OTP program memory allows one-time factory or field programming, making the part well suited to mature production runs where firmware is fixed. Architecturally, the device uses a Harvard-style separated program/data bus, 12-bit instruction width, and CMOS process technology for low power. It runs from a single 3.0V to 6.25V supply (commercial/industrial variants) at up to 4 MHz, producing 1 MIPS throughput. The 8-bit data path with 12-bit opcodes yields compact code density that fits easily within the 512-word OTP space. Typical applications include appliance controls, low-end consumer products, simple sensor interfaces, battery chargers, LED drivers, and industrial timers where a small, inexpensive, deterministic 8-bit core is preferred over a 16-/32-bit MCU. The industrial temperature grade extends deployment into factory and outdoor equipment. When designing with this part, choose an external 4 MHz crystal or resonator for clock accuracy, drive MCLR with a proper reset circuit, and reserve RA0-RA3 digital I/O pins carefully because some packages multiplex analog functions onto them. The OTP memory cannot be erased, so use a PIC16F55 flash equivalent for prototyping.

RFQ যোগাযোগ
PIC16C55A-04I/SO - 8-Bit OTP MCU, 4MHz, 768B | Microchip
PIC16C55A-04I/SO

PIC16C55A-04I/SO - 8-Bit OTP MCU, 4MHz, 768B | Microchip

The Microchip Technology PIC16C55A-04I/SO is an 8-bit EPROM/ROM-based CMOS microcontroller from the PIC16C5X family, operating at 4 MHz with 768 bytes of One-Time-Programmable (OTP) program memory (512 x 12) and 24 bytes of RAM, housed in a 28-pin SOIC package. This industrial-temperature (-40C to +85C) device delivers 20 digital I/O pins, a two-level hardware stack, and a single 8-bit timer/counter (TMR0) with watchdog capability. An OTP microcontroller (One-Time-Programmable MCU) is a microcontroller whose program memory is implemented as one-time-writable EPROM rather than flash. OTP MCUs occupy the middle ground between mask-ROM parts (lowest cost at high volume, but cannot be programmed in the field) and flash-based MCUs (re-programmable, higher cost per bit). OTP is widely used in cost-sensitive, high-volume consumer and industrial products where the firmware is finalized before production and field updates are not required. Within the broader taxonomy, PIC16C55A is a microcontroller -> 8-bit MCU -> RISC MCU -> CMOS MCU -> semiconductor. Key specifications include 12-bit wide instructions for 2:1 code compression versus other 8-bit MCUs, direct/indirect/relative addressing modes, 33 instruction set, and compatibility with the PIC16C5X baseline. The device runs from 3.0V to 6.0V, supports in-circuit serial programming (ICSP) via the PICmicro mid-range family convention, and is well-suited for high-volume embedded designs that have moved beyond prototyping. Its 4 MHz clock delivers up to 1 MIPS of throughput, sufficient for simple control loops and user-interface tasks. Architecturally, the PIC16C55A employs a Harvard-style RISC core with separate program and data buses, allowing instruction fetch and operand read to occur in a single cycle except for branches. The OTP array is organized as 512 x 12, and the data memory is structured as 24 general-purpose registers plus special-function registers mapped into a common file. Reset is provided by power-on, MCLR, and watchdog expiry, with brown-out detection unavailable on this baseline part. Typical applications include appliance control (washing machines, microwave user-interface boards), battery chargers, LED drivers, simple sensor signal conditioning, low-end remote controls, and replacement of discrete logic. Designers choose this part when absolute lowest unit cost matters more than field re-programmability and the code footprint fits within 768 bytes. For new designs, prefer PIC16F54 (flash, pin-compatible drop-in upgrade) or PIC16C558 (more memory, same 28-SOIC footprint). Designers should note that this part is in Microchip's NRND lifecycle - order lifetime-buy quantities if your product must ship beyond the last-time-buy cutoff. This page synthesizes distributor pricing, pin-compatible PIC16C5X alternatives, and practical migration guidance to PIC16F54 flash parts not found in any single datasheet or distributor listing.

RFQ যোগাযোগ
PIC16C55A-04I/SS - 4MHz 8-bit OTP MCU, 20 I/O, SSOP-28 | Microchip
PIC16C55A-04I/SS

PIC16C55A-04I/SS - 4MHz 8-bit OTP MCU, 20 I/O, SSOP-28 | Microchip

The Microchip Technology PIC16C55A-04I/SS is a low-cost, high-performance 8-bit fully-static CMOS microcontroller from the PIC16C5X family, delivering 4 MHz maximum clock speed with 768 bytes (512 x 12) of One-Time-Programmable (OTP) EPROM program memory in a 28-pin SSOP (Shrink Small Outline Package). The device exposes 20 bidirectional digital I/O pins, 24 bytes of RAM, and a single 8-bit Timer0 with an 8-bit prescaler for real-time event counting. The 'I' suffix denotes the industrial operating temperature range of -40C to +85C, while '04' specifies the 4 MHz maximum oscillator frequency, and 'SS' indicates the SSOP-28 surface-mount package. What is a microcontroller? A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory, working RAM, configurable I/O peripherals, and one or more timers on one piece of silicon. Within the broader taxonomy, an MCU is a sub-category of integrated circuit -> microprocessor -> semiconductor. The PIC16C5X family is positioned as an entry-level 8-bit RISC MCU optimized for cost-sensitive, low-pin-count embedded control, where its compact 33-instruction instruction set and 12-bit-wide opcode enable 2:1 code compression versus typical 8-bit CISC competitors in the same price class. Key features of the PIC16C55A include only 33 single-word/single-cycle instructions (most execute in 200 ns at 20 MHz oscillator, equivalent to a 4 MHz instruction rate for the -04 speed grade), a 2-level hardware call stack, direct/indirect/relative addressing modes for both data and instructions, and seven or eight special-function hardware registers. An 8-bit real-time clock/counter (TMR0) with user-programmable prescaler supports timing, event-counting, and pulse-width measurement. The on-chip watchdog timer (WDT) with its own on-chip RC oscillator enables autonomous recovery from code-flow faults without external components, which is critical for unattended industrial installations. Power-saving SLEEP mode reduces I_DD to a few microamps for battery-operated applications, and the device operates across 2.5 V to 6.25 V V_DD. Architecturally, the PIC16C55A employs a Harvard-style RISC core with separate program and data paths, providing deterministic instruction throughput and immunity to data-bus contention. The OTP EPROM is windowless and one-time-programmable, giving the device its 'C' (CMOS/OTP) designation; for windowed UV-erasable prototypes, the JW ceramic package variant exists. The 12-bit instruction word delivers strong code density, and the all-static design permits the oscillator to be stopped without losing internal register state - a useful trait for low-power designs. Typical applications include appliance controls, automotive body electronics, low-end security panels, simple sensor signal conditioning, fan and pump controllers, and any high-volume embedded product where cost, small footprint, and proven PIC ecosystem tooling outweigh the need for modern peripherals like USB or CAN. Because the part is marked 'Not Recommended for new designs' by Microchip, it is best reserved for maintenance of installed equipment. When designing with the PIC16C55A, note that the 4 MHz speed grade limits computational throughput; verify instruction-cycle margins at your maximum external event rate. Decoupling V_DD with a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin, plus a 10 uF bulk reservoir at the regulator output, is essential for clean POR behavior on industrial supply rails. This page consolidates current distributor pricing, parametric drop-in alternatives, and engineering design notes not typically aggregated on a single datasheet - giving maintenance and sourcing engineers a one-stop reference for legacy PIC16C55A inventory decisions.

RFQ যোগাযোগ
PIC16C55A-20/SO - 8-Bit 20MHz OTP MCU 768B 28-SOIC | Microchip
PIC16C55A-20/SO

PIC16C55A-20/SO - 8-Bit 20MHz OTP MCU 768B 28-SOIC | Microchip

The Microchip Technology PIC16C55A-20/SO is an 8-bit RISC CMOS microcontroller belonging to the PIC16C5X family, delivering 20 MHz maximum clock speed with 768 bytes (512 x 12) of One-Time-Programmable (OTP) program memory in a 28-pin SOIC surface-mount package. The device exposes 20 digital I/O pins, integrates 24 bytes of general-purpose RAM, and provides 12-bit-wide instruction words with single-cycle execution across 33 instruction opcodes for compact code density. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and a Harvard or modified-Harvard architecture. Within the broader hierarchy, MCUs sit inside the microcontrollers category, which itself belongs to integrated circuits, semiconductor devices, and finally electronic components. The PIC16C5X family specifically represents Microchip's lowest-cost OTP/EPROM-based controllers targeted at high-volume, cost-sensitive embedded designs where re-programmability is not required after deployment. Key features include an 8-bit timer/counter (TMR0) with programmable prescaler, two-level hardware stack, support for direct, indirect and relative addressing modes, and a wide 2.0V to 6.0V operating voltage range. The fully static CMOS design allows the clock to be stopped without losing register contents, and the RISC architecture achieves 2:1 code compression versus typical 8-bit CISC competitors in the same price class. On the technical depth side, the PIC16C55A-20/SO implements a two-stage pipeline, executes one instruction per clock cycle (except branches), and offers seven or eight special-function hardware registers mapped into its data memory. The 20 MHz oscillator version provides approximately 5 MIPS throughput, which is ample for appliance control, simple sensor interfaces, and low-cost user-interface glue logic. Typical applications include consumer appliance controllers, LED display drivers, low-end remote controls, battery chargers, security keypads, and educational/hobbyist platforms. Because the program memory is OTP, designers must commit firmware before final assembly, making the part best suited to mature, stable code bases. When designing with this device, allocate sufficient decoupling (0.1 uF ceramic near VDD) and respect the 20 MHz maximum oscillator limit with appropriate crystal loading capacitance. The 28-SOIC package supports hand-soldering but is also fully compatible with automated pick-and-place assembly for production runs. This page consolidates current distributor pricing, same-package drop-in alternatives from the Microchip PIC16C5X family and cross-brand equivalents, application design notes, and a parameter comparison table not available on any single manufacturer or distributor page.

RFQ যোগাযোগ
PIC16C55A-20/SP - 8-Bit 20MHz OTP MCU, 20 I/O, SPDIP-28 | Microchip
PIC16C55A-20/SP

PIC16C55A-20/SP - 8-Bit 20MHz OTP MCU, 20 I/O, SPDIP-28 | Microchip

Microchip Technology PIC16C55A-20/SP is an 8-bit RISC microcontroller in the PIC16C5X baseline family, supplied in a 28-pin SPDIP (Skinny Plastic DIP) package. It integrates 768 bytes of one-time-programmable (OTP) program memory (organized as 512 x 12 words), 24 bytes of RAM, and runs the PIC16 instruction set at up to 20 MHz clock rate with 200 ns instruction cycle. The device provides 20 general-purpose digital I/O pins arranged across ports RA and RB, two 8-bit timer/counters (TMR0 and TMR1) plus a watchdog timer, and a two-level hardware stack for subroutine nesting. A baseline PIC microcontroller is an 8-bit CMOS MCU that executes a compact 12-bit-wide instruction set optimized for low-cost embedded control. It belongs to the hierarchy: PIC16C5X -> PIC16 family -> 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor. Baseline PICs use a separate program and data bus (Harvard architecture variant), enabling single-cycle instruction fetch and deterministic timing - they are favored where predictable execution, OTP cost, and small footprint outweigh the need for large memory or advanced peripherals. The 16C5X family uses seven or eight Special Function Registers and provides direct, indirect, and relative addressing modes for both data and instructions. Key features include an 8-bit real-time clock/counter (TMR0) with programmable prescaler, a Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable recovery, on-chip power-on reset (POR), and brown-out detection. Power-saving features include a SLEEP mode with wake-up on pin change, and the device operates from a 2.5 V to 5.5 V supply. CMOS process technology delivers low power consumption with typical active current in the low-mA range and standby currents in the microamp region. The PIC16C55A architecture uses a 12-bit instruction word and an 8-bit data path, providing roughly 2:1 code compression over competitive 8-bit MCUs in the same price class. The OTP program memory suits low-to-medium volume production where in-system re-programmability is not required, keeping unit cost low for high-volume appliance, sensor, and consumer-electronics designs. Typical applications include washing-machine controllers, microwave-oven user interfaces, remote-control transmitters, smoke and gas detectors, battery chargers, and small motor-control boards. Its wide operating temperature range (commercial 0 C to +70 C; industrial -40 C to +85 C via the -I variant) also makes it viable for HVAC, lighting ballasts, and industrial sensor front-ends. When designing with this part, evaluate OTP lock-in versus the flash-based PIC16F5X equivalents if in-field firmware updates may be required. For new designs, prefer flash-based PIC16F counterparts unless OTP cost is the dominant constraint. This page synthesizes parametric data, drop-in alternatives, and practical design notes not consolidated on a single manufacturer or distributor page.

RFQ যোগাযোগ
PIC16C55A-20E/P - 8-Bit 20MHz OTP MCU, 768B, 28-PDIP | Microchip
PIC16C55A-20E/P

PIC16C55A-20E/P - 8-Bit 20MHz OTP MCU, 768B, 28-PDIP | Microchip

The Microchip Technology PIC16C55A-20E/P is an 8-bit RISC microcontroller from the PIC® 16C family, operating at up to 20 MHz clock speed with 768 bytes (512 x 12) of OTP program memory and 25 bytes of RAM, housed in a 28-pin PDIP through-hole package. It offers 20 general-purpose I/O pins, automotive temperature grade (-40C to +125C), and an operating voltage range of 3.0V to 6.0V typical. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and programmable I/O peripherals. The PIC16C5X family is positioned at the entry level of the 8-bit RISC MCU taxonomy: PIC16C5X -> PIC16C family -> PIC microcontrollers -> 8-bit microcontrollers -> microcontrollers -> embedded ICs. The 12-bit wide instruction set provides 2:1 code compression over competing 8-bit MCUs, allowing more functionality in fewer bytes of program memory. Key features include a 33-instruction set, 12-bit wide instructions, 2:1 code compression versus competitors, 8-bit data path, 20 MHz maximum clock frequency, and one-time programmable (OTP) program memory. The 28-pin PDIP package provides breadboard-friendly through-hole mounting suitable for prototyping, education, and legacy industrial systems. Architecturally, the PIC16C55A uses a Harvard-architecture RISC core with separate program and data buses. The OTP memory is programmed once and cannot be erased, making the device well-suited to high-volume, cost-sensitive applications where firmware is finalized at production. The automotive temperature grade extends operating range to -40C to +125C, distinguishing the 'E' suffix from commercial-grade variants. Typical applications include automotive embedded controllers, legacy industrial control systems, appliance control boards, prototyping platforms, educational development boards, and cost-sensitive replacement designs. The 28-pin PDIP form factor remains popular for through-hole manufacturing lines and hobbyist development. When designing with this device, note that OTP memory cannot be field-updated - any firmware bug requires physical IC replacement. Use the parallel programming mode and a Microchip-approved device programmer (such as the MPLAB PM3) for production programming. This page synthesizes distributor pricing from DigiKey/Mouser, automotive-grade drop-in alternatives in the same 28-PDIP footprint, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55A-20E/SO - 20MHz 8-Bit OTP MCU | Microchip | 28-SOIC
PIC16C55A-20E/SO

PIC16C55A-20E/SO - 20MHz 8-Bit OTP MCU | Microchip | 28-SOIC

The Microchip Technology PIC16C55A-20E/SO is a 20 MHz, 8-bit, fully static, EPROM/OTP-based CMOS microcontroller in the PIC16C5X family, housed in a 28-pin SOIC (SO) 0.295-inch/7.50 mm wide surface-mount package. The "-20E" suffix denotes the 20 MHz maximum clock speed and the extended (-40C to +125C) operating temperature grade. It integrates 768 bytes of EPROM/OTP program memory (organized as 512 x 12 words), 24 bytes of general-purpose SRAM, 12-bit instruction word architecture, and 20 digital I/O pins arranged across four ports (RA, RB, RC, RD). A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory, working RAM, and configurable I/O peripherals on one IC. The PIC16C5X family occupies the entry-level, cost-optimized branch of Microchip's 8-bit PIC portfolio, descending from the broader class of 8-bit microcontrollers -> microcontrollers -> embedded processors -> semiconductors. It uses a RISC instruction set with 33 single-cycle instructions, has no onboard peripherals beyond the core I/O and timer, and is intended for high-volume cost-sensitive applications where OTP programmability is acceptable. Key features of the PIC16C55A-20E/SO include 768 bytes of OTP program memory, 24 bytes of RAM, four I/O ports (PORTB 8-bit, PORTC 8-bit, PORTD 4-bit plus RA 4-bit variant), a 20 MHz maximum oscillator frequency, and a wide 3.0 V to 5.5 V supply range. The 20 MHz clock enables a 200 ns instruction cycle at full speed; instructions are 12 bits wide, providing compact code density. The device uses an external oscillator and supports crystal, ceramic resonator, or RC clock inputs. Architecturally, the PIC16C55A uses a Harvard RISC core with separate program and data paths, a 12-bit instruction word, and a 2-level hardware stack. Its reset and watchdog timing characteristics are defined in the manufacturer datasheet. There is no integrated UART, ADC, or interrupt controller beyond the basic external/port-change interrupt on PORTB, making this part one of the simplest members of the PIC16C5X family and the closest sibling of the PIC16C54A and PIC16C57C. Typical applications for the PIC16C55A-20E/SO include low-cost consumer appliances, simple motor controllers, LED display drivers, automotive body controllers (using the -E temperature grade), battery chargers, remote-control transmitters, and any high-volume embedded design that requires OTP one-time programmable memory rather than flash. The PIC16C5X is often selected where field upgrades are unnecessary and unit cost is the primary driver. When designing with this device, note that OTP memory cannot be rewritten in-circuit, so the firmware must be fully verified on EPROM-windowed samples (PIC16C55A-20/JW) before committing to OTP production. The lack of an internal oscillator means an external clock source must always be supplied, and the wide 0.295-inch SO body requires careful clearances in compact layouts. This page synthesizes distributor pricing, drop-in OTP/EPROM and FLASH alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55A-20E/SP - 8-Bit 20MHz OTP MCU 768B | Microchip
PIC16C55A-20E/SP

PIC16C55A-20E/SP - 8-Bit 20MHz OTP MCU 768B | Microchip

The Microchip Technology PIC16C55A-20E/SP is an 8-bit RISC microcontroller from the PIC16C5X family operating at up to 20 MHz, with 768 bytes (512 x 12-bit words) of One-Time Programmable (OTP) program memory, 25 bytes of RAM, and packaged in a 28-pin SPDIP (SP) through-hole DIP. The "E" suffix denotes the extended industrial temperature grade of -40C to +125C, while the trailing /SP indicates the SPDIP-28 plastic dual-in-line package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral interfaces into one package. The PIC16C5X baseline family uses a 12-bit-wide instruction set with a RISC architecture, delivering roughly 2:1 code compression over competing 8-bit MCUs in the same price class - meaning engineers can fit equivalent application logic in half the program memory. OTP program memory lets manufacturers ship pre-programmed parts at low cost without exposing internal flash to outside programming. Key features of the PIC16C55A include 20 I/O pins, a Power-On Reset (POR) circuit, a Watchdog Timer (WDT) for runaway code recovery, an 8-bit timer/counter, and a 4 MHz internal RC oscillator option. The device operates across 3.0V to 6.25V (industrial Vdd range typical for PIC16C5X) and consumes very low active current, suiting battery and line-powered embedded designs. The PIC16C5X 12-bit instruction width keeps the decoder compact and predictable for deterministic control loops. Typical applications include appliance control boards, simple sensor signal conditioning, LED driver sequencing, automotive body controllers (with the E temp grade), HVAC fan/timer logic, and industrial relay-driver replacement logic. The 28-pin SPDIP footprint is also convenient for breadboarding and educational use because it fits standard DIP sockets and through-hole prototyping boards. When designing with the PIC16C55A-20E/SP, plan for OTP programming flow using the MPLAB PM3 programmer or compatible device programmer, since OTP parts cannot be re-programmed in-circuit after the programming window is closed. Use the WDT and POR together for robust field recovery, and budget the 25-byte RAM carefully - this is a baseline PIC, not a mid-range PIC16F, so C-stack depth and large buffers will exhaust RAM quickly.

RFQ যোগাযোগ
PIC16C55A-20I/P - 8-Bit 20MHz OTP MCU 768B | Microchip
PIC16C55A-20I/P

PIC16C55A-20I/P - 8-Bit 20MHz OTP MCU 768B | Microchip

The Microchip PIC16C55A-20I/P is a low-cost, high-performance 8-bit fully-static EPROM/ROM-based CMOS microcontroller in a 28-pin PDIP package, operating at 20 MHz with industrial temperature range support. It integrates 768 bytes of program memory (512 x 12 OTP), 24 bytes of RAM, and 20 general-purpose I/O pins, providing a compact solution for simple embedded control. A microcontroller (MCU) is a single-chip computer that contains a processor core, memory, and programmable input/output peripherals. The PIC16C5X family from Microchip Technology belongs to the broader category of 8-bit microcontrollers -> microcontrollers -> microprocessors -> semiconductors. These devices implement a RISC architecture with 33 single-word, single-cycle instructions and a 12-bit wide instruction word, achieving 2:1 code compression over competing 8-bit MCUs in the same price class. Key features of the PIC16C55A-20I/P include a 20 MHz maximum clock speed, 20 MHz operating frequency, a two-level deep hardware stack, direct/indirect/relative addressing modes, and an 8-bit real-time clock/counter (TMR0) with 8-bit programmable prescaler. It supports a wide operating voltage range typical of the PIC16C5X family, with low power consumption suitable for battery and industrial applications. From an architectural standpoint, the device uses a Harvard-style separated program and data bus, with the 12-bit instruction path enabling efficient encoding of arithmetic, branch, and bit-oriented operations in a single cycle. The PIC16C55A derivative of the PIC16C5X series offers expanded I/O (20 pins) and program memory (512 x 12) relative to the PIC16C54 base device, with OTP one-time-programmable EPROM for cost-sensitive production runs. Note: This device is marked as 'Not Recommended for new designs' (NRND) by Microchip; for new designs, Microchip recommends the PIC16F57-I/P family. Typical applications include industrial control logic, automotive body electronics, simple sensor interfaces, appliance controls, and battery-powered instrument subsystems. The 20 MHz instruction execution rate and 20 GPIO make the device well-suited for tasks such as keypad scanning, LED driving, and low-speed serial protocols. Industrial temperature grade (-40C to +85C) extends its suitability to factory automation and outdoor equipment. When designing with the PIC16C55A-20I/P, ensure the system clock source (RC oscillator, crystal, or resonator) matches the 20 MHz maximum rating, and respect the two-level hardware stack depth when writing interrupt or call-heavy code. Engineers targeting new designs should evaluate the Flash-based PIC16F57-I/P as a migration path that preserves pin-out while adding reprogrammability and longer-life cycle status. This page synthesizes distributor stock levels, parametric equivalents, pricing tiers, and practical design notes not found in the manufacturer datasheet, enabling faster component selection and risk assessment for both new designs and legacy maintenance scenarios.

RFQ যোগাযোগ
PIC16C55A-20I/SP - 8-bit OTP MCU, 20MHz, 768B, SPDIP-28 | Microchip
PIC16C55A-20I/SP

PIC16C55A-20I/SP - 8-bit OTP MCU, 20MHz, 768B, SPDIP-28 | Microchip

The Microchip Technology PIC16C55A-20I/SP is a member of the PIC16C5X family of 8-bit CMOS microcontrollers featuring a RISC architecture with 12-bit wide instructions and an 8-bit wide data path. The device operates at a maximum clock speed of 20 MHz, contains 768 bytes (512 x 12) of one-time-programmable (OTP) program memory and 24 bytes of RAM, and provides up to 20 digital I/O pins in a 28-pin SPDIP package. The "/SP" suffix denotes the SPDIP-28 through-hole package while the "/I" suffix denotes the industrial operating temperature range of -40C to +85C. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, working RAM, and peripherals such as I/O ports, timers, and interrupt logic. Within the broader taxonomy, the PIC16C55A belongs to the 8-bit MCU class -> RISC MCU -> Harvard-architecture MCU -> embedded controller -> semiconductor. The PIC16C5X family uses a 12-bit instruction word with a 2:1 code compression advantage over competing 8-bit MCUs of its era, and its symmetric instruction set reduces development time significantly. Key features of the PIC16C55A-20I/SP include seven or eight special function hardware registers, a two-level deep hardware stack, and direct, indirect, and relative addressing modes for both data and instructions. An 8-bit real-time clock/counter (TMR0) with a programmable prescaler is integrated, along with a watchdog timer for unattended operation. The architecture uses a modified Harvard design with separate program and data buses for deterministic instruction execution. Typical applications include appliance control, automotive subsystems, industrial process control, security and access systems, and low-end consumer products where cost-sensitive embedded control is needed. The device is supported by the PICmicro Mid-Range Reference Manual and the MPLAB PM3 Universal Device Programmer for code development and OTP programming. When designing with this part, note that OTP memory cannot be reprogrammed in-circuit - firmware bugs require part replacement. Provide a clean +5V supply with adequate decoupling (100 nF plus 10 uF bulk) on VDD, and respect the 5V absolute maximum rating when driving industrial loads. The PIC16C55A is rated for 5V operation only and does not support the wider voltage range of later Flash-based PIC16F parts. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the PIC16C5X family, lifecycle status, and practical design notes not consolidated in any single manufacturer document.

RFQ যোগাযোগ
PIC16C55A-20I/SS - 8-Bit 20MHz 768B OTP MCU SSOP-28 | Microchip
PIC16C55A-20I/SS

PIC16C55A-20I/SS - 8-Bit 20MHz 768B OTP MCU SSOP-28 | Microchip

The Microchip Technology PIC16C55A-20I/SS is an 8-bit CMOS ROM-based microcontroller from the PIC16C5X family, delivering 20MHz maximum clock speed with 768 bytes (512 x 12) of One-Time-Programmable (OTP) program memory in a 28-pin SSOP package. The device provides 24 bytes of RAM, 20 digital I/O lines, and is rated for industrial temperature operation from -40C to +85C. According to the Microchip product page, this part carries a "Not Recommended for new designs" status, meaning it remains available for legacy maintenance but Microchip directs new designs to the Flash-based PIC16F5X family. An 8-bit microcontroller is a single-chip computer that integrates a CPU, program memory, working RAM, and peripheral I/O on one die. The PIC16C5X family implements a RISC Harvard architecture with 12-bit-wide instructions and an 8-bit-wide data path, achieving approximately 2:1 code compression over other 8-bit MCUs in its class. Within the broader microcontroller hierarchy, the PIC16C55A belongs to the mid-range 8-bit category, positioned between baseline PIC10/12/16 devices and 16-bit PIC24/dsPIC families. OTP program memory allows one-time factory or field programming using a device programmer such as the MPLAB PM3, making the part cost-optimized for high-volume fixed-function products. Key features of the PIC16C55A-20I/SS include a 20MHz maximum operating frequency, 24-byte general-purpose RAM, 20 bidirectional I/O pins, one 8-bit real-time clock/counter (TMR0), Power-On Reset (POR), Watchdog Timer (WDT), and a two-level hardware stack supporting direct, indirect, and relative addressing modes. Seven or eight special-function hardware registers manage peripheral control. The 28-pin SSOP package provides compact surface-mount integration at approximately 5.3mm body width, well-suited for space-constrained designs. The PIC16C55A uses a RISC architecture executing most instructions in a single cycle, with a 12-bit instruction word and 33 single-word instructions. This compact instruction set yields high code density, reducing total program memory requirements and overall system cost. The two-level hardware stack limits call depth to two levels, which constrains interrupt-driven or deeply nested subroutine architectures but is adequate for simple sequential control loops. Typical applications include appliance control, industrial sensor interfaces, simple motor drivers, LED controllers, consumer electronics, automotive subsystems (non-safety), battery chargers, and any cost-sensitive embedded system where the OTP memory model fits the production volume profile. The industrial temperature grade extends applicability to factory automation, HVAC controls, and outdoor equipment. When designing with this device, plan for the two-level hardware stack limitation, the OTP memory programming workflow (which requires a device programmer and cannot be re-flashed in-circuit), and the legacy lifecycle status. For new designs, evaluate Flash-based PIC16F5X equivalents that provide in-circuit programmability and longer-term supply assurance.

RFQ যোগাযোগ
PIC16C55A-40/P - 8-Bit OTP MCU 40MHz 768B | Microchip | 28-PDIP
PIC16C55A-40/P

PIC16C55A-40/P - 8-Bit OTP MCU 40MHz 768B | Microchip | 28-PDIP

The Microchip Technology PIC16C55A-40/P is an 8-bit RISC microcontroller from the PIC16C5X family, featuring 768 bytes of One-Time-Programmable (OTP) program memory organized as 512 x 12 words, 32 bytes of RAM, and a maximum clock frequency of 40 MHz. It is housed in a 28-pin Plastic DIP (PDIP) through-hole package with a 0.600 inch (15.24 mm) row spacing, making it suitable for legacy through-hole designs, prototyping, and industrial control boards. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8-bit Harvard-architecture RISC microcontrollers originally developed by General Instrument's microelectronics division and later popularized by Microchip Technology. PIC microcontrollers occupy the hypernym hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. They are widely used in embedded systems for their low cost, simple instruction set, deterministic timing, and broad peripheral integration. Key features of the PIC16C55A include a 12-bit instruction word delivering 2:1 code compression versus competitors in its class, 20 I/O pins, a watchdog timer, power-on reset, and an operating voltage range of 3.0 V to 5.5 V. The 40 MHz speed grade denotes the maximum oscillator frequency; the instruction cycle is one quarter of the oscillator frequency (4 MHz instruction rate at 40 MHz clock). The PIC16C55A is built on a CMOS process with EPROM/OTP program memory, delivering approximately an order-of-magnitude higher performance than its 8-bit competitors in the same price category. The device supports commercial temperature grades (0C to +70C) and is targeted at cost-sensitive, high-volume embedded applications. Typical applications include simple motor control, appliance control, automotive body electronics (non-safety), remote transmitters, sensor interfaces, and consumer electronics where proven 8-bit performance is sufficient. The 28-PDIP package enables hand-soldering and socket replacement, simplifying prototyping and field service. When designing with this part, note that the OTP memory cannot be re-programmed in-circuit. Engineers evaluating modern replacements should consider the PIC16F54 or PIC16F57 in PDIP packages, which offer Flash memory for iterative development while sharing code compatibility. This page synthesizes distributor pricing, lifecycle status, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55A-40/SS - 8-bit 40MHz OTP MCU, 768B Code | Microchip
PIC16C55A-40/SS

PIC16C55A-40/SS - 8-bit 40MHz OTP MCU, 768B Code | Microchip

The Microchip Technology PIC16C55A-40/SS is an 8-bit RISC-based OTP (One-Time Programmable) microcontroller from the PIC16C5X family, featuring 768 bytes of program memory, 24 bytes of RAM, and 20 I/O pins, operating at up to 40 MHz clock frequency and housed in a 28-pin SSOP (Shrink Small Outline Package) with gull-wing leads. It belongs to Microchip's baseline PIC family, the industry's first 8-pin to 28-pin family of microcontrollers, designed for cost-sensitive embedded applications with simple control tasks. What is a microcontroller (MCU)? A microcontroller is a single-chip computer that integrates a CPU core, memory (program + data), and peripheral interfaces (I/O, timers, etc.) into one IC. Within that hierarchy, the PIC16C5X sits in the baseline 12-bit-instruction family, which later expanded into the enhanced mid-range (14-bit) and PIC18 (16-bit) families. The 12-bit wide instructions deliver high code density - typically 2:1 compression versus competing 8-bit MCUs - allowing more functionality to fit in the small on-chip OTP memory. Key features of the PIC16C55A-40/SS include 768 bytes of EPROM program memory (OTP), 24 bytes of data RAM, a 4 MHz internal RC oscillator option (selected at programming), a 40 MHz maximum external clock input, and 20 bidirectional digital I/O pins across two ports (RA, RB). The device has only 28 instructions, enabling fast learning curves, and provides a watchdog timer with on-chip RC oscillator for reliable unattended operation. Architecturally, the PIC16C55A uses a Harvard architecture with separate program and data buses, a single accumulator-based ALU, and a deep hardware stack for subroutine nesting. The 12-bit instruction width and 8-bit data path balance code density against silicon cost, which is why this family remains popular in high-volume appliance and consumer products where BOM cost dominates. Typical applications include remote controls, small appliance controllers (toasters, coffee machines, fan controllers), security keypads, sensor signal conditioning, LED chaser/sequencer lights, and simple battery-operated toys. Its 20 I/O pins are sufficient to scan 4x4 keypads while driving multiplexed displays. When designing with this part, plan for one-time programming: the EPROM memory cannot be erased. For prototype work, use a windowed (JW) variant or a pin-compatible Flash MCU (PIC16F) for in-circuit reprogramming. The 28-pin SSOP footprint is shared with the PIC16C55, PIC16C554, and PIC16C558 families, simplifying PCB layout reuse across product variants. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes - information not consolidated on any single distributor or manufacturer page. All specifications are sourced from the Microchip PIC16C55A datasheet and distributor listings verified as of 2026-09-16.

RFQ যোগাযোগ
PIC16C55AT-04/SO - 8-Bit 4MHz OTP MCU 768B | Microchip
PIC16C55AT-04/SO

PIC16C55AT-04/SO - 8-Bit 4MHz OTP MCU 768B | Microchip

The Microchip Technology PIC16C55AT-04/SO is an 8-bit RISC microcontroller from the PIC16C5X family, featuring 768 bytes (512 x 12) of One-Time-Programmable (OTP) program memory, 24 bytes of RAM, and 20 digital I/O pins. The device operates from a single 5V supply and runs at a 4 MHz oscillator frequency in a 28-pin SOIC wide-body package supplied on tape-and-reel. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and I/O peripherals on a single silicon die. The PIC16C5X family uses a 12-bit-wide instruction word with a RISC (Reduced Instruction Set Computer) architecture that delivers roughly 2:1 code compression versus other 8-bit MCUs in its class, enabling simpler firmware development. Within the broader taxonomy, this part is a microcontroller (MCU) -> embedded controller -> semiconductor device, designed for cost-sensitive embedded control where deterministic instruction timing and minimal external components are priorities. Key features of the PIC16C55AT-04/SO include a 4 MHz internal/external clock input, 33 single-word instructions, a two-level hardware stack, 20 bidirectional I/O pins organized into three ports (RA, RB, RC), and a programmable Watchdog Timer (WDT) with on-chip RC oscillator. The OTP program memory is programmed once via Microchip's standard ICSP-compatible serial programming interface. Power consumption is typically 2 mA at 5V/4 MHz, with sleep/idle current under typical CMOS standby levels. The device is built on a baseline PIC architecture using static CMOS logic, meaning the clock can be stopped without losing internal register state - useful for power-saving designs. It supports interrupt-driven control via the global interrupt enable and individual peripheral flags, and includes a Power-on Reset (POR), power-up Timer (PWRT), and Oscillator Start-up Timer (OST) for reliable cold-start behavior without external reset circuitry. Typical applications include appliance control, automotive body electronics (non-safety), LED display drivers, simple sensor interfaces, and remote transmitters/receivers. The wide SOIC-28 footprint is suitable for hand-soldered prototypes as well as high-volume SMT production lines. When designing with the PIC16C55AT-04/SO, note that OTP memory cannot be erased or reprogrammed - firmware bugs require physical part replacement. Engineers targeting field updates should consider the flash-based PIC16F5X family instead. The /SO suffix indicates the SOIC-28 wide-body tape-and-reel packaging for SMT assembly. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet, helping engineers source and integrate this legacy OTP MCU efficiently.

RFQ যোগাযোগ
PIC16C55AT-04/SS - 8-bit OTP MCU 768B 20 I/O 4MHz SSOP-28 | Microchip
PIC16C55AT-04/SS

PIC16C55AT-04/SS - 8-bit OTP MCU 768B 20 I/O 4MHz SSOP-28 | Microchip

The Microchip Technology PIC16C55AT-04/SS is a member of the PIC16C5X family of low-cost, high-performance 8-bit fully-static EPROM/ROM-based CMOS microcontrollers. Housed in a 28-pin SSOP package (0.209", 5.30 mm width), it integrates 768 bytes of One-Time-Programmable (OTP) program memory organized as 512 x 12, 24 bytes of data RAM, and 20 digital I/O pins. The device operates from a 3 V to 6.25 V supply and runs at a maximum clock speed of 4 MHz, executing most instructions in a single 250 ns cycle. What is an 8-bit OTP microcontroller? An 8-bit OTP MCU is a small, fixed-instruction-set processor whose program memory can be written exactly once (One-Time-Programmable) using an EPROM-style bit cell. The "8-bit" designation refers to the width of the ALU and the data bus; the PIC16C5X family uses a 12-bit-wide instruction word to achieve 2:1 code compression over competing 8-bit MCUs. In the broader taxonomy, OTP microcontrollers sit between mask-ROM MCUs (cheapest at high volume) and Flash MCUs (re-programmable, higher cost per bit). They are favored for cost-sensitive, high-volume, stable-firmware applications. Key features include a RISC architecture with only 33 single-word/single-cycle instructions, an 8-bit timer/counter, a watchdog timer for reliable operation, and a power-saving SLEEP mode. The device is built on a CMOS process that yields low power consumption and high noise immunity. It supports in-circuit serial programming through Microchip's standard tools and is compatible with the PICSTART Plus and MPLAB development environments, allowing the same firmware to migrate across the PIC16C5X family. Typical applications for the PIC16C55AT-04/SS include low-end consumer appliances, automotive sub-systems (body controllers, lighting drivers), industrial control loops, sensor interfaces, and remote-control transmitters. The 20 I/O pins are well-suited to keypad scanning, LED matrix driving, and small-stepper or DC-motor control via external drivers. The industrial-grade temperature range and SSOP footprint also enable space-constrained designs. When designing with this device, allocate I/O pins carefully because the PIC16C5X has a fixed 12-bit program word and limited RAM (24 bytes); high-volume data structures should be stored in program memory using RETLW lookup tables. Place a 0.1 microfarad decoupling capacitor within 5 mm of VDD and use the on-chip oscillator with a 4 MHz crystal or ceramic resonator; bypass the MCLR pin according to the datasheet to ensure a clean reset. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16C5X family, and practical design notes that complement the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55AT-04E/SO - 8-Bit 4MHz OTP MCU 28-SOIC | Microchip
PIC16C55AT-04E/SO

PIC16C55AT-04E/SO - 8-Bit 4MHz OTP MCU 28-SOIC | Microchip

The Microchip Technology PIC16C55AT-04E/SO is an 8-bit PIC microcontroller from the PIC16C5X family, featuring a RISC CPU core operating at 4 MHz, 768 bytes (512 x 12) of One-Time-Programmable (OTP) EPROM program memory, and 25 bytes of RAM, housed in a 28-pin SOIC wide-body package. Operating from 3.0 V to 5.5 V and -40 C to +125 C, it delivers deterministic performance for embedded control applications. Tape-and-reel suffix ("/SO") indicates the factory packaging form for high-volume SMT assembly lines. An 8-bit OTP microcontroller is a single-chip computer built around an 8-bit data path with non-volatile program memory that can be written exactly once via EPROM programming. In the system hierarchy, OTP MCUs sit below flash-based MCUs (re-programmable) and above mask-ROM MCUs (factory-programmed), within the broader category of microcontrollers, embedded controllers, and finally semiconductors. The PIC16C5X family pioneered Microchip's baseline RISC architecture with 12-bit wide instructions yielding 2:1 code compression versus 8-bit competitors. Key features include 20 digital I/O pins, a hardware timer/counter, watchdog timer, power-on reset, brown-out detection, and low-power SLEEP mode. The fully static CMOS design eliminates the need for a continuous clock and supports DC operation down to zero frequency, allowing the device to wake from interrupts for ultra-low standby power. The 12-bit instruction set is highly orthogonal, reducing development time and code density. The device employs a Harvard architecture with separate program and data buses, single-cycle instructions (except program branches which take two), and a four-stage pipeline. The 4 MHz clock with 250 ns instruction cycle delivers up to 4 MIPS throughput, sufficient for sensor reading, simple actuator control, and user-interface tasks in cost-sensitive embedded products. Typical applications include industrial control, consumer electronics, automotive body and convenience subsystems, and white-goods appliance controllers. The 28-SOIC footprint is well suited for hand-soldered prototypes as well as high-volume pick-and-place production. When designing, allocate one port pin to MCLR, leave adequate decoupling on VDD/VSS, and verify timing budgets using worst-case 4 MHz oscillator tolerance. The 'E' suffix denotes the extended temperature grade (-40 C to +125 C), required for automotive and industrial environments. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C55AT-04E/SS - 8-bit 4MHz OTP MCU 768B | Microchip
PIC16C55AT-04E/SS

PIC16C55AT-04E/SS - 8-bit 4MHz OTP MCU 768B | Microchip

The Microchip Technology PIC16C55AT-04E/SS is an 8-bit EPROM/ROM-based CMOS microcontroller from the PIC16C5X family, operating at up to 4 MHz with 768 bytes (512 x 12) of One-Time Programmable (OTP) program memory and 25 bytes of RAM in a 28-pin SSOP package. The extended (-E) temperature grade and tape-and-reel (T) suffix make this variant suitable for industrial-grade surface-mount designs and high-volume automated assembly. Core architecture delivers RISC performance with 33 single-word instructions, 12-bit-wide instruction words, and 8-level deep hardware stack. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on one die. Within the broader semiconductor taxonomy it sits below microprocessors (no on-chip memory) and above digital signal processors (no general-purpose I/O model). The PIC16C5X family is positioned as a low-cost, high-performance baseline 8-bit MCU family. Program memory is OTP (one-time programmable) EPROM rather than flash, which reduces per-unit cost in mature, code-stable applications but requires masked-ROM or windowed-EPROM alternatives for prototyping or low-volume runs. Key features include 20 general-purpose digital I/O pins arranged across ports A and B, an integrated Watchdog Timer (WDT) with on-chip RC oscillator for reliable operation, a Power-On Reset (POR) circuit, and a 4 MHz internal/external clock domain. The device operates from 2.5 V to 6.25 V across the extended -40C to +125C industrial temperature range. The 28-SSOP package has 5.30 mm body width and gull-wing leads compatible with standard surface-mount reflow profiles. Designers choose this part for cost-sensitive embedded control loops where 768 bytes of code are sufficient - appliance timers, remote-control transmitters, low-end sensor interfaces, simple motor controllers, and battery-powered instrumentation. The RISC core delivers deterministic instruction timing that simplifies real-time scheduler design. Because program memory is OTP EPROM, code must be fully validated before programming - this part is a production-only choice rather than a development platform. When using the PIC16C55AT-04E/SS, observe the 4 MHz maximum clock frequency at 5 V supply - derate to 2 MHz at 2.5 V operation per Microchip datasheet curves. The WDT must be disabled in software (OPTION register) if not used, otherwise it can cause unintended resets. Decouple VDD with a 0.1 microfarad ceramic capacitor placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in compatible same-footprint alternatives, and engineering guidance not collected in the manufacturer datasheet alone. Cross-brand pin-compatible equivalents are flagged where they exist on the open market.

RFQ যোগাযোগ