মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC16C56A/JW - 8-Bit 20MHz 1.5KB EPROM MCU | Microchip
PIC16C56A/JW

PIC16C56A/JW - 8-Bit 20MHz 1.5KB EPROM MCU | Microchip

The Microchip Technology PIC16C56A/JW is an 8-bit RISC CMOS microcontroller in the PIC16C5x family, integrating 1.5 KB (1K x 12) of One-Time-Programmable UV-erasable EPROM program memory and 25 bytes of data RAM. The JW suffix indicates the 18-pin CERDIP windowed package, which exposes the die for UV erasure and reprogramming during development and prototyping. According to the Microchip product listing on DigiKey, the part runs at up to 20 MHz across a 2.5 V to 6.25 V operating range and ships as 8-bit data-path / 12-bit instruction-width RISC core. A PIC microcontroller (Programmable Intelligent Computer, also known as Peripheral Interface Controller) is a Harvard-architecture RISC MCU family in which program and data memories occupy separate address spaces. The PIC16C5x sub-family is the legacy "baseline" tier of PIC microcontrollers, positioned below the PIC16C7x/8x mid-range family and well below the PIC18 enhanced family in the modern Microchip taxonomy. The 'C' suffix denotes CMOS EPROM technology (later replaced by flash-based PIC16F parts), and the JW package is reserved almost exclusively for engineering development because of its quartz window and high cost. Key features of the PIC16C56A include seven or eight special-function hardware registers, a two-level deep hardware call stack, direct/indirect/relative addressing modes, an 8-bit real-time clock/counter (TMR0) with a programmable prescaler, 12 programmable digital I/O lines, a Power-on Reset (POR) block, and a Watchdog Timer (WDT) for unattended operation. The Harvard architecture separates the 12-bit program bus from the 8-bit data bus, allowing instruction fetch and operand access to occur in the same cycle. Typical applications include low-cost 8-bit embedded control in industrial timers and counters, appliance controllers, simple sensor front-ends, LED and relay driver boards, and educational/hobbyist platforms where the UV-erasable window allows repeated firmware iteration. The JW windowed CERDIP package is rarely used in production builds because the OTPEPROM can be erased and reprogrammed in-circuit by exposing the die to UV light through the quartz window. Designers should note that the PIC16C56A is widely regarded as mature/legacy silicon. For new designs, Microchip recommends the flash-based PIC16F54 in a modern SOIC or QFN package. The CERDIP JW variant is best reserved for development, lab work, and legacy board repair. Pricing varies significantly with availability because of limited production runs.

RFQ যোগাযোগ
PIC16C56AT-04/SO - 4MHz 8-bit OTP MCU 1.5KB | Microchip SOIC-18
PIC16C56AT-04/SO

PIC16C56AT-04/SO - 4MHz 8-bit OTP MCU 1.5KB | Microchip SOIC-18

The Microchip Technology PIC16C56AT-04/SO is an 8-bit EPROM/ROM-based CMOS microcontroller belonging to the PIC16C5X family, delivering 4 MHz CPU performance with 1.5 KB (1K x 12) of One-Time-Programmable (OTP) program memory and 25 bytes of RAM in a 18-pin SOIC (Small Outline) package. Housed in an industry-standard 18-SOIC (0.295 inch / 7.50 mm body width) surface-mount package with gull-wing leads, this commercial-temperature grade device provides 12 I/O pins and operates from a single 5 V supply. The 'T' suffix denotes tape and reel packaging, while the 'A' suffix indicates an enhanced silicon revision (PIC16C56A) of the baseline PIC16C56, and '04' specifies the 4 MHz maximum clock rate. An 8-bit microcontroller (MCU) is a self-contained computing element that integrates a CPU core, non-volatile program memory, working RAM, and programmable I/O peripherals on a single CMOS die. The PIC16C5X family represents one of the earliest reduced-instruction-set computing (RISC) architectures adopted in mainstream microcontrollers, employing a 12-bit-wide instruction word that yields roughly 2:1 code compression versus competing 8-bit CISC architectures in the same era. Within the broader taxonomy, this device sits at the hierarchy: 8-bit MCU -> RISC microcontroller -> microcontroller -> embedded processor -> semiconductor IC. Key differentiating specifications of the PIC16C56AT-04/SO include its 33 single-word (12-bit) instructions, fully static CMOS design that allows clock rates down to DC, dedicated watchdog timer with on-chip RC oscillator, power-saving SLEEP mode, and wide operating voltage range. The 12-bit instruction width and Harvard bus architecture deliver deterministic throughput of one instruction per two clock cycles, enabling predictable interrupt response suitable for cost-sensitive real-time control loops. Typical applications include low-cost appliance control, automotive interior lighting (non-safety), simple sensor interfaces, hobby robotics, and replacement of discrete logic in legacy designs. The OTP program memory is ideal for short production runs or prototype deployments where mask-ROM volume economics are not justified. The 4 MHz CPU clock combined with 1K instruction words provides sufficient headroom for state-machine-style controllers in industrial and consumer products. When designing with this part, designers should note the absence of in-circuit serial programming (ICSP) on early PIC16C5X silicon - code is loaded via a parallel programmer socket prior to solder mounting, or via windowed ceramic packages. The '04' speed grade must not be exceeded; 20 MHz variants use the '-20' suffix. For new designs, the flash-based PIC16F57 family offers modern in-circuit programmability at the cost of changed non-volatile memory technology. This page consolidates distributor pricing, drop-in alternatives, parametric comparison, and design notes not aggregated on any single manufacturer or distributor page, providing a faster engineering reference than individual datasheet searches.

RFQ যোগাযোগ
PIC16C56AT-04/SS - 8-Bit 4MHz OTP MCU, 1.5KB | Microchip
PIC16C56AT-04/SS

PIC16C56AT-04/SS - 8-Bit 4MHz OTP MCU, 1.5KB | Microchip

The Microchip Technology PIC16C56AT-04/SS is an 8-bit EPROM/ROM-based CMOS microcontroller from the PIC16C5X family, operating at up to 4MHz with 1.5KB (1K x 12) of One-Time-Programmable (OTP) program memory, packaged in a 20-pin SSOP (Shrink Small Outline Package). The 'T' suffix denotes tape-and-reel packaging, '/SS' indicates the SSOP-20 footprint, and the '-04' speed grade specifies the 4MHz maximum clock frequency. The device targets cost-sensitive, high-volume embedded applications where deterministic RISC execution and minimal external component count are critical. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and programmable I/O peripherals. 8-bit MCUs such as the PIC16C5X occupy the low-cost, low-power segment of the embedded market, making them well-suited for appliance control, sensor signal conditioning, and standalone industrial timers where 16- or 32-bit processing is unnecessary. The PIC family uses a Harvard RISC architecture with 12-bit-wide instructions and only 33 single-word instructions, achieving 2:1 code compression over competing 8-bit architectures. Key features of the PIC16C56AT-04/SS include 25 bytes of RAM, 12 digital I/O pins, an internal oscillator option, a Watchdog Timer with its own on-chip RC oscillator, and power-saving SLEEP mode. The device operates from 3.0V to 5.5V across the commercial 0C to +70C temperature range, drawing only a few mA active and microamp-level current in SLEEP. The fully static CMOS design allows the clock to be stopped without losing register contents, simplifying low‑power sequencing. The PIC16C5X architecture is a classic RISC implementation with a two-stage pipeline, allowing most instructions to execute in a single 250ns instruction cycle at 4MHz. The 12-bit instruction word keeps program memory density high, and the 8-bit-wide data path is sufficient for byte-oriented control loops. Peripherals are limited intentionally to keep die size and cost low: timer/counter, GPIO, and reset logic are the primary on-chip resources. OTP program memory allows the customer to write the device once at production time, ideal for mature, fixed-function products. Typical applications for the PIC16C56AT-04/SS include simple motor and solenoid drivers, low-end consumer appliance control (coffee makers, handhelds, toys), LED sequencing modules, automotive interior accessories, and small sensor-interface boards. The 12 I/O pins are adequate for keypad scanning, relay driving, and UART-style bit-banged communication. Because OTP is one-time programmable, this part is best suited for high-volume production where firmware is finalized before mask programming. When designing with this device, plan for an in-circuit serial programming (ICSP) header even on production boards so OTP can be written after PCB assembly. Decouple VDD with a 100nF ceramic capacitor placed within 5mm of the pin, and provide a clean MCLR reset path with the recommended 10k pull-up. If in-application reprogrammability is required, consider a flash-based PIC16F5X equivalent. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC16C5X family, and practical design notes that complement the manufacturer datasheet.

RFQ যোগাযোগ
PIC16C56AT-04E/SO - 8-bit OTP MCU, 4MHz, 1.5KB | Microchip
PIC16C56AT-04E/SO

PIC16C56AT-04E/SO - 8-bit OTP MCU, 4MHz, 1.5KB | Microchip

The Microchip Technology PIC16C56AT-04E/SO is an 8-bit EPROM/OTP-based CMOS microcontroller from the PIC16C5X family, delivering 4 MHz CPU performance with 1.5 KB (1K x 12) of one-time-programmable program memory and 25 bytes of RAM in an 18-pin SOIC package. It integrates 12 digital I/O lines, an 8-bit timer with watchdog, power-on reset, and a RISC architecture that executes most instructions in a single 250 ns cycle. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces on one silicon die. The PIC16C5X family belongs to the 8-bit microcontroller taxonomy, sitting beneath broader categories of microcontrollers, embedded processors, and finally integrated circuits. These classic PIC MCUs serve cost-sensitive, deterministic control applications where 12-bit wide instructions deliver 2:1 code compression versus competing 8-bit architectures of the same era. Key features include an extended operating temperature range of -40C to +125C (the 'E' suffix), 4 MHz maximum clock at 4 MHz crystal/RC oscillator input, 12 I/O pins with high-current sink/source capability, an 8-bit real-time timer/counter, watchdog timer with on-chip RC oscillator, power-on reset, and code protection. The 18-SOIC (0.295 inch / 7.50 mm width) package supports legacy surface-mount designs with reliable hand-soldering and standard IR reflow profiles. The PIC16C56AT uses an enhanced Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and data access. Its 33 single-word instructions and 12-bit-wide instruction word simplify compiler output and hand-coded assembly, while the fully static design enables operation down to DC clock speeds for low-power sleep implementations. Typical applications include appliance control, automotive sub-systems (body electronics, lighting controllers), industrial sensor interfaces, simple motor control, smart card readers, and battery-powered instrument front-ends. The 1.5 KB program memory fits state-machine logic, lookup tables, and small protocol stacks including I2C bit-banging or LIN slave handlers. When designing with this device, note that the OTP memory cannot be reprogrammed - choose the PIC16F56 flash sibling or PIC16C56A-20/SO windowed ceramic-package variant for development. Decoupling VDD with 0.1 uF close to the pins is mandatory; the MCLR reset pin requires a pull-up for normal operation. This page synthesizes distributor inventory, parametric alternatives, and practical design notes beyond the manufacturer datasheet, helping engineers source, qualify, and design-in the PIC16C56AT-04E/SO with confidence.

RFQ যোগাযোগ
PIC16C56AT-20/SO - 8-bit OTP MCU 1.5KB ROM 20MHz SOIC-18
PIC16C56AT-20/SO

PIC16C56AT-20/SO - 8-bit OTP MCU 1.5KB ROM 20MHz SOIC-18

The Microchip Technology PIC16C56AT-20/SO is an 8-bit EPROM/ROM-based CMOS microcontroller belonging to the PIC16C5X family, supplied in a 18-lead small-outline (SOIC-18 / "SO") package and rated for 20 MHz maximum clock operation. It integrates 1.5 KB (1K x 12) of One-Time Programmable (OTP) program memory and 25 bytes of general-purpose SRAM, packaged in a gull-wing surface-mount SOIC outline suitable for hand-soldered prototyping and automated assembly. According to the manufacturer datasheet and distributor listings, the device is commercial temperature grade with 12 bidirectional digital I/O pins arranged across two ports (GPIO/RA and GPB/RC depending on sub-variant) and is intended for cost-sensitive embedded control applications. The PIC16C56A sub-family is a superset of the original PIC16C56, adding an additional 8-bit I/O port, edge-selectable interrupts, higher drive current, and a wider operating voltage envelope versus the legacy PIC16C56. Background Knowledge: An 8-bit OTP microcontroller is a single-chip computer built around an 8-bit data path and one-time-programmable (OTP) EPROM or ROM program memory. The PIC16C5X family uses a 12-bit wide instruction word with a Harvard architecture, separating program and data memory for deterministic single-cycle instruction execution. As a member of the broader microcontroller class (microcontroller -> MCU -> embedded controller -> semiconductor), the PIC16C56A belongs to the RISC subset, executes one instruction per instruction cycle (four clock periods), and is offered in masked-ROM (PIC16C56), UV-erasable windowed (PIC16C56 JW), and one-time-programmable EPROM (PIC16C56A) variants, with the "T" suffix denoting the tape-and-reel packaging option. Key features include 12 I/O pins, 20 MHz maximum oscillator input, a 33-instruction RISC instruction set, on-chip power-on reset, watchdog timer with its own on-chip RC oscillator, internal MCLR reset input, programmable code protection, power-saving SLEEP mode, and selectable oscillator configurations (RC, LP, XT, HS, external clock). The 20 in the part number suffix designates the 20 MHz speed grade, the T denotes tape-and-reel, and /SO denotes the SOIC-18 wide-body small-outline package. Typical applications span consumer appliances, automotive subsystems (non-safety), industrial control nodes, sensor interfaces, and low-cost battery-powered devices that benefit from deterministic single-cycle RISC execution and a mature toolchain based on MPLAB IDE and the MP3/MPLAB PM3 device programmer. When designing with the PIC16C56AT-20/SO, ensure the Vdd decoupling network (typically 0.1 µF ceramic in parallel with a bulk tantalum/electrolytic cap) is placed within 10 mm of the supply pin, and respect the maximum I/O sink/source ratings per pin and per port.

RFQ যোগাযোগ
PIC16C56AT-20/SS - 8-bit OTP MCU, 1.5KB, 12 I/O, 20MHz | Microchip
PIC16C56AT-20/SS

PIC16C56AT-20/SS - 8-bit OTP MCU, 1.5KB, 12 I/O, 20MHz | Microchip

The Microchip Technology PIC16C56AT-20/SS is an 8-bit RISC CMOS microcontroller from the PIC16C5x baseline family, featuring 1.5KB (1K x 12) of One-Time-Programmable (OTP) program memory, 25 bytes of data RAM, and 12 digital I/O pins. It executes instructions at a 20MHz clock rate from a 4.5V to 5.5V supply, and is housed in a 20-pin SSOP package with tape-and-reel packaging for high-volume surface-mount assembly. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and configurable I/O peripherals onto one silicon die. Within the semiconductor hierarchy, the PIC16C5x sits below modern 32-bit Cortex-M parts and above simple logic ICs, serving as a low-cost, deterministic, ultra-low-power embedded controller. OTP memory means the program is written once and cannot be electrically erased, which lowers per-unit cost versus flash-based MCUs while still supporting in-circuit programming at production. Key features of this part include the PIC RISC architecture with 33 single-word/single-cycle instructions (12-bit wide), 2:1 code compression versus competitive 8-bit MCUs, a hardware 8-bit timer/counter with optional prescaler, watchdog timer for reliability, Power-on Reset, brown-out detection, and a wide commercial operating temperature range. The 12 I/O pins can each drive or sink up to 25mA, enabling direct LED or relay drive without external buffers. Typical applications include low-cost consumer appliance control, simple sensor interfaces, battery-powered remote controls, LED lighting controllers, smoke-detector logic boards, and industrial timers. Its deterministic instruction timing and small footprint also make it useful in legacy system upgrades where a proven 8-bit baseline MCU is required. When designing with this device, plan the OTP programming step into the production line - the 'A' suffix indicates an automotive-qualified temperature grade, while the 'T' suffix denotes tape-and-reel packaging. Decoupling the VDD pin with a 100nF ceramic capacitor placed within 5mm of the package is strongly recommended for noise immunity.

RFQ যোগাযোগ
PIC16C56AT-20E/SO - 8-Bit 20MHz OTP MCU 1.5KB | Microchip
PIC16C56AT-20E/SO

PIC16C56AT-20E/SO - 8-Bit 20MHz OTP MCU 1.5KB | Microchip

The Microchip PIC16C56AT-20E/SO is an 8-bit RISC microcontroller from the PIC16C5X family, providing 1.5KB (1K x 12) of One-Time-Programmable (OTP) EPROM program memory, 25 bytes of RAM, and 12 I/O pins in an 18-pin SOIC wide-body package. It executes instructions at a 20 MHz maximum clock rate, delivering up to 5 MIPS of throughput from a Harvard-architecture core with a 12-bit wide instruction word that yields 2:1 code compression versus typical 8-bit CISC microcontrollers. The device operates from a single 3.0 V to 5.5 V supply and features Power-on Reset (POR), Watchdog Timer (WDT), and a wide -40 °C to +125 °C extended operating temperature range suitable for industrial and automotive-grade designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral I/O on one die. The PIC16C5X family belongs to the broader category of 8-bit microcontrollers -> embedded controllers -> microprocessors -> semiconductors. These MCUs are designed for deterministic, low-cost embedded control where bit-manipulation efficiency, low power draw, and small code footprint outweigh the need for high MIPS. Within a system, the PIC16C56A typically serves as the master controller, replacing discrete logic and reducing BOM count on simple sensor, motor, and human-interface boards. Key features of the PIC16C56AT-20E/SO include its 33 single-word instructions, 2-level hardware stack, 8-bit timer/counter with 8-bit programmable prescaler, direct LED drive capability on all port pins, and low-power consumption of typically < 2 mA at 5 V and 20 MHz. The OTP EPROM memory enables fast prototyping and low-volume production runs while keeping per-unit cost low, and the 12-bit instruction set simplifies compiler and assembler porting versus 14-bit or 16-bit PIC cores. Typical applications include automotive body controllers, appliance control boards, sensor signal conditioning, low-end remote-control transmitters, and simple user-interface panels. Because the part is offered in tape-and-reel packaging with an automotive temperature grade, it is well-suited for in-cabin automotive modules and white-goods designs that must survive extended thermal stress. When designing with this device, note that OTP memory can be programmed only once, so firmware should be fully validated before commitment. Decoupling VDD with a 0.1 µF ceramic capacitor placed within 5 mm of the supply pin is recommended, and unused I/O pins should be configured as outputs low to minimize quiescent current draw. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes that go beyond the manufacturer datasheet to accelerate BOM qualification and supply-chain risk mitigation.

RFQ যোগাযোগ
PIC16C56AT-20E/SS - 8-Bit 20MHz 1.5KB OTP MCU 20-SSOP | Microchip
PIC16C56AT-20E/SS

PIC16C56AT-20E/SS - 8-Bit 20MHz 1.5KB OTP MCU 20-SSOP | Microchip

The Microchip Technology PIC16C56AT-20E/SS is an 8-bit CMOS RISC microcontroller from the PIC16C5X family, featuring 1.5KB (1K x 12) of One-Time Programmable (OTP) program memory, 25 bytes of RAM, and 12 I/O pins, housed in a 20-pin SSOP package. It operates up to 20MHz at 5V and includes essential peripherals such as Power-On Reset (POR) and a Watchdog Timer (WDT), making it a compact, deterministic control core for cost-sensitive embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral interfaces on one die. The PIC16C5X family belongs to the broader category of 8-bit microcontrollers -> RISC microcontrollers -> embedded controllers -> semiconductor ICs, and represents one of the earliest commercially successful Harvard-architecture MCU lines from Microchip. Its 12-bit wide instructions provide roughly 2:1 code compression over typical 8-bit CISC contemporaries, which was a key selling point in the 1990s and remains attractive for tight assembly routines. Key features of the PIC16C56AT-20E/SS include a fully static CMOS design that allows the clock to be stopped without losing register state, a wide 3.0V to 6.0V operating range, a low-power sleep mode that drops supply current to the microampere range, and a 20MHz maximum clock frequency at 5V that yields a 200ns instruction cycle. The 12 I/O pins are bidirectional with individually programmable direction registers, and the 8-bit timer/counter (TMR0) with an 8-bit programmable prescaler is sufficient for basic event counting and PWM generation. The OTP program memory and 25-byte RAM make the device suitable for high-volume, fixed-function appliances where firmware is finalized at production time. Architecture-wise, the PIC16C56A uses a 14-bit instruction word with a two-stage pipeline (fetch/execute overlap), enabling most instructions to complete in one instruction cycle. The device has no interrupt controller, only a single hardware interrupt source from the TMR0 overflow and the external GP2/INT pin, which keeps the silicon small and the firmware deterministic. Peripherals are kept to a minimum to reduce cost: POR, WDT, TMR0, and the I/O ports. The 'E' suffix denotes the Enhanced (-40C to +125C) operating temperature range, and the 'T' in the part number indicates Tape & Reel packaging. The '20' speed suffix specifies the 20MHz maximum clock. Typical applications include small appliance controllers (rice cookers, microwave oven keypads, washing-machine front panels), battery chargers, toys and educational electronics, remote control transmitters, low-cost sensor interface boards, and replacement logic for legacy designs in industrial control panels. The wide supply range and small SSOP footprint also suit handheld instrumentation and consumer white goods. When designing with this part, note that OTP memory cannot be re-programmed; prototypes should use a windowed ceramic or flash-based PIC16F5X equivalent for firmware development. The 25-byte RAM constraint forces tight stack and variable management, and the absence of a hardware multiplier means multiply operations must be performed in software. This page synthesizes distributor pricing, drop-in compatible PIC16C5X family alternatives, and design considerations not typically compiled in the manufacturer datasheet, helping engineers compare the PIC16C56AT-20E/SS against modern flash-based and OTP replacements in the same SSOP-20 footprint.

RFQ যোগাযোগ
PIC16C56AT-40/SS - 8-bit 40MHz OTP MCU 1.5KB | Microchip
PIC16C56AT-40/SS

PIC16C56AT-40/SS - 8-bit 40MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56AT-40/SS is an 8-bit RISC microcontroller from the PIC® 16C family, delivering 40 MHz maximum clock speed with 1.5 KB (1K x 12) of One-Time Programmable (OTP) program memory, packaged in a 20-pin SSOP (Shrink Small Outline Package, 5.30 mm body width). It features 25 bytes of RAM, 12 I/O pins, Power-On Reset (POR), and a Watchdog Timer (WDT). An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on one silicon die. The 8-bit PIC architecture uses a RISC (Reduced Instruction Set Computer) instruction set with a fixed program word width of 12 bits in this family, enabling single-cycle instruction execution at the oscillator clock rate. MCUs serve as the embedded intelligence in countless products, from consumer appliances to industrial controllers, forming the lowest tier of the computing hierarchy: microcontroller -> embedded processor -> microprocessor. The OTP memory variant is factory- or field-programmed once and cannot be erased, which lowers die cost for high-volume production runs. Key features of the PIC16C56AT-40/SS include its 40 MHz maximum operating frequency, 1.5 KB OTP program memory (1K x 12 organization), 25 bytes of general-purpose RAM, 12 digital I/O pins, two 8-bit timers, a watchdog timer for runaway code recovery, and Power-On Reset. It is offered in the commercial temperature grade (0 °C to +70 °C) per the slash-SPEC ordering code "40" suffix convention, with an operating voltage range typically of 3.0 V to 6.0 V across the PIC16C5X family. Technically, the PIC16C56A core uses a Harvard architecture with separate program and data buses. The 12-bit instruction word delivers deterministic single-cycle execution for most instructions and a 33-instruction set. With 25 bytes of file-register RAM and a 2-level hardware stack, this device targets simple control loops where deterministic timing and low cost outweigh deep memory and modern peripherals. Typical applications include appliance control boards, HVAC thermostat logic, simple sensor signal conditioning, LED driver controllers, and legacy industrial control replacement. The 40 MHz clock rate enables sub-microsecond bit-banging for protocol emulation, while 12 I/O pins are sufficient for keypad scan, relay drive, and indicator-LED multiplexing. When designing with this part, account for OTP programming cost during development: OTP parts cannot be re-programmed, so production must use pre-programmed parts. For development, the windowed (JW) or flash (F) variants in the broader PIC16 family are recommended. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on any single manufacturer or distributor page, providing a single reference point for engineers qualifying the PIC16C56AT-40/SS for new designs or legacy board replacements.

RFQ যোগাযোগ
PIC16C56T-10/SS - 8-Bit 10MHz OTP MCU 1.5KB | Microchip
PIC16C56T-10/SS

PIC16C56T-10/SS - 8-Bit 10MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-10/SS is an 8-bit RISC microcontroller from the PIC16C5X family, housed in a 20-pin SSOP surface-mount package with tape-and-reel packaging. It integrates 1.5KB (1K x 12) of One-Time Programmable (OTP) EPROM program memory, 25 bytes of data RAM, and a 10 MHz internal clock core. A microcontroller (MCU) is a single-chip computer containing a CPU, memory, and I/O peripherals. The PIC16C5X family is a low-cost, high-performance, 8-bit, fully static, EPROM/ROM-based CMOS microcontroller family widely used as a successor to classic 8-bit designs. Within the broader hierarchy, PIC microcontrollers sit under the 8-bit MCU category, which itself belongs to the embedded microcontroller -> integrated circuit -> semiconductor taxonomy. Key features of the PIC16C56T-10/SS include an operating voltage range of 4.5V to 5.5V, an operating temperature range of 0C to +70C (commercial grade), 12-bit-wide instruction word, 33 single-word instructions, and a single 8-bit timer/counter. The CMOS process technology provides low power consumption suitable for both battery-powered and line-powered embedded designs. The device uses a Harvard RISC architecture with separate code and data buses, an 8-level deep hardware stack, and direct/indirect addressing modes. It supports up to 12 I/O pins with individual direction control and offers a watchdog timer option for reliable operation in noisy industrial environments. Typical applications include industrial automation controllers, consumer electronics (remote controls, small appliances, toys), automotive subsystems (non-safety body electronics), low-end embedded control, and replacement of legacy 8-bit designs. The PIC16C56T-10/SS is particularly suitable for cost-sensitive, low-volume production where OTP programming is acceptable. When designing with this device, note that OTP memory cannot be erased or rewritten - it is intended for pre-programmed production parts. For prototyping or field-upgradable designs, consider the Flash-based PIC16F5X family instead. The wide SSOP footprint also simplifies hand-soldering during development. This page consolidates distributor pricing, drop-in SSOP alternatives, and practical design notes that complement the Microchip datasheet to accelerate your component selection.

RFQ যোগাযোগ
PIC16C56T-10E/SS - 8-Bit 10MHz OTP MCU, 20-SSOP | Microchip
PIC16C56T-10E/SS

PIC16C56T-10E/SS - 8-Bit 10MHz OTP MCU, 20-SSOP | Microchip

The Microchip Technology PIC16C56T-10E/SS is an 8-bit RISC microcontroller from the PIC16C5X family, featuring 10 MHz maximum clock speed, 1.5 KB (1K x 12) of One-Time Programmable (OTP) EPROM program memory, and 25 bytes of RAM, all integrated into a 20-pin SSOP package. The 'E' suffix denotes the Enhanced temperature grade (-40C to +125C) and 'T' indicates tape-and-reel packaging for automated assembly. An 8-bit OTP microcontroller is a single-chip computer that integrates CPU, memory, and peripherals on a single silicon die, where 'OTP' (One-Time Programmable) means the program memory can be written only once using an EPROM cell. The PIC16C5X architecture is classified under the broader hierarchy: microcontroller -> embedded MCU -> 8-bit MCU -> CMOS RISC MCU -> PIC architecture. These devices excel in cost-sensitive, high-volume applications where field reprogramming is not required, often replacing discrete logic in appliances, toys, and simple control loops. Key features include a 12-bit instruction word providing 2:1 code compression over competitive 8-bit MCUs, 33 single-word instructions, and a two-level hardware stack. Built-in peripherals include a Watchdog Timer (WDT) for reliable operation in noisy environments, Power-On Reset (POR), and a programmable code-protection bit. The CMOS design delivers very low power consumption, making the part attractive for always-on applications. The wide 2.5V-6.25V operating range further expands its deployment flexibility. The PIC16C56 architecture uses a Harvard-style separate program/data bus with a 12-bit program memory width, enabling single-cycle instruction fetch. This RISC core delivers close to 5 MIPS at 10 MHz, sufficient for state-machine control, simple sensor interfacing, and basic serial-protocol bit-banging. The 20-pin SSOP footprint is shared across the PIC16C5X family, allowing easy migration between PIC16C54, PIC16C55, PIC16C56, and PIC16C57 derivatives. Typical applications include remote controls, battery chargers, LED lighting controllers, security keypads, sensor interface modules, and small appliance controls such as coffee makers and fan controllers. The 1.5 KB OTP memory typically supports 1000+ instructions, adequate for substantial control logic in embedded products. When designing with this device, note that OTP cannot be reprogrammed, so firmware must be fully validated before programming. Plan for code protection if intellectual property is a concern. The PIC16C5X family uses a legacy instruction set not directly compatible with newer PIC16 enhanced cores.

RFQ যোগাযোগ
PIC16C56T-10I/SO - 8-Bit 10MHz OTP MCU 1.5KB | Microchip
PIC16C56T-10I/SO

PIC16C56T-10I/SO - 8-Bit 10MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-10I/SO is an 8-bit RISC microcontroller from the PIC16C5X family featuring a 10 MHz maximum operating frequency, 1.5 KB (1K x 12) of One-Time Programmable (OTP) program memory, and 25 bytes of RAM, housed in an 18-pin SOIC (SOP) package. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that combines a CPU, program memory, RAM, and peripherals onto a single integrated circuit. The PIC16C5X family belongs to Microchip's foundational PIC architecture — a Harvard-type RISC design in which program and data memory are accessed on separate buses — that achieves roughly 2:1 code compression over competitive 8-bit CISC MCUs of its era thanks to its 12-bit wide, highly symmetrical instruction set. This positions the PIC16C56 as a low-cost, high-performance member of the linear regulator -> power management hierarchy of legacy embedded control. Key specifications include a 10 MHz external oscillator input, an 8-bit ALU, two 8-bit I/O ports, a 12-bit instruction word, single-word instructions with single-cycle execution (except branches), a watchdog timer with on-chip RC oscillator, and an internal power-on reset circuit. The device supports industrial temperature operation (-40C to +85C) as indicated by the 'I' suffix and is supplied in tape and reel packaging as indicated by the 'T' suffix. The PIC16C5X architecture uses a simple two-stage pipeline with a 12-bit program memory bus and an 8-bit data bus, allowing most instructions to execute in a single 200 ns instruction cycle at 20 MHz (400 ns at 10 MHz). The OTP program memory is programmed once via standard Microchip device programmers and cannot be erased — a deliberate cost trade-off that suits mature, fixed-function designs rather than prototyping. Typical applications include simple logic replacement, low-end consumer appliances, automotive subsystems (climate control, lighting, instrument clusters), industrial timers and counters, battery chargers, and remote controls. Designers migrating from 8051-family MCUs value the PIC16C5X instruction set for its orthogonal, easy-to-learn assembly language and the broad ecosystem of MPLAB development tools. A key design consideration is OTP program memory: once a device is programmed, the firmware is permanent and cannot be field-updated. For designs that require firmware revisions, the PIC16F5X flash-based family is a drop-in architectural alternative. Engineers should also budget for an external oscillator or resonator in XT mode, as the device does not include an internal high-frequency oscillator. This page synthesizes distributor pricing, same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC16C56T-10I/SS - 8-Bit 10MHz OTP MCU 1.5KB | Microchip
PIC16C56T-10I/SS

PIC16C56T-10I/SS - 8-Bit 10MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-10I/SS is an 8-bit CMOS RISC microcontroller in the PIC16C5X family, featuring a 10MHz maximum operating frequency, 1.5KB (1K x 12) of One-Time Programmable (OTP) program memory, and 25 bytes of RAM, housed in a 20-pin SSOP package. The 'T' suffix indicates tape-and-reel packaging and the 'I' suffix denotes the industrial -40C to +85C operating temperature range. The 'SS' suffix indicates the 5.30mm-wide 20-SSOP surface-mount package. An 8-bit microcontroller (MCU) is a programmable digital logic device that integrates a CPU, non-volatile program memory, working RAM, and peripheral I/O onto a single silicon die. The PIC16C5X family uses a Harvard architecture with a 12-bit-wide instruction word, delivering 2:1 code compression versus competing 8-bit MCUs in its price class. The PIC16C56 specifically is the lowest-cost member of the family, omitting the on-chip EEPROM data memory and peripheral count of higher-end siblings, making it suited to cost-sensitive, high-volume embedded control applications. Key features include 12 I/O lines capable of sourcing/sinking up to 25mA per pin for direct LED or transistor drive, an 8-bit timer/counter with a programmable prescaler, a watchdog timer with its own on-chip RC oscillator for maximum reliability, and a power-saving SLEEP mode. The fully static CMOS design allows clock frequencies from DC to 10MHz, enabling the MCU to idle at zero current consumption. Operating voltage is 3.0V to 5.5V (5V typical), and the architecture uses a two-stage pipeline that nearly all instructions execute in a single 200ns instruction cycle at 10MHz. Typical applications include consumer appliance control, low-end remote-control transmitters, automotive body electronics (non-safety), LED lighting controllers, sensor signal conditioning, and battery-powered devices. The 12-bit instruction width and RISC instruction set simplify assembler programming for tight code-footprint designs. When designing with this device, ensure the OTP memory is programmed only once - code bugs cannot be field-updated. Use the PICSTART or MPLAB ICD tools for development. Add a 100nF decoupling capacitor between VDD and VSS within 5mm of the pins, and reserve the MCLR pin for an external reset circuit unless internal WDT reset is acceptable.

RFQ যোগাযোগ
PIC16C56T-HS/SO - 8-Bit 20MHz OTP MCU, 1.5KB | Microchip
PIC16C56T-HS/SO

PIC16C56T-HS/SO - 8-Bit 20MHz OTP MCU, 1.5KB | Microchip

The Microchip Technology PIC16C56T-HS/SO is an 8-bit EPROM/ROM-based CMOS microcontroller from the PIC16C5x family, delivering 20 MHz maximum clock speed with 1.5KB (1K x 12) of OTP program memory and 25 bytes of RAM, housed in an 18-pin SOIC (SO) package supplied on tape and reel. The "T" suffix denotes tape-and-reel packaging, "HS" indicates the high-speed 20 MHz oscillator mode, and "SO" specifies the 0.295-inch wide 18-SOIC outline. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral I/O on one die. The PIC16C5x family belongs to Microchip's original baseline RISC architecture (12-bit instruction word, 33 instructions) and sits within the broader hierarchy of: microcontroller -> embedded controller -> semiconductor IC. These classic OTP devices are one-time-programmable, meaning each unit can be programmed once during manufacturing or by the OEM but cannot be rewritten in the field, which historically lowered per-unit cost for high-volume embedded products. Key features include 12 digital I/O pins arranged across two ports (PORTA 4-bit, PORTB 8-bit), a hardware 8-bit timer/counter with programmable prescaler, watchdog timer with on-chip RC oscillator, power-on reset, and a 4.5V to 5.5V commercial operating range. The device draws only a few mA active and supports power-saving SLEEP mode with wake-up via watchdog or external interrupt. The HS (high-speed) oscillator option accommodates 20 MHz crystal or ceramic resonator timing sources for designs requiring faster instruction throughput (200 ns instruction cycle). Typical applications include legacy industrial control modules, appliance controllers, automotive body electronics, simple sensor interfaces, low-end remote controls, and white-goods user-interface boards. The wide software base and stable toolchain (MPLAB IDE, PICSTART+ programmer) make it a workhorse for cost-sensitive embedded designs that have shipped for decades and remain in maintenance. When designing with this part, note that OTP memory cannot be updated after programming - firmware changes require a new part. The PIC16C56 has no in-circuit debugger interface, so emulator or ICE tools are needed for code development. Current consumption rises with clock frequency; plan decoupling accordingly.

RFQ যোগাযোগ
PIC16C56T-HSE/SO - 8-Bit 16MHz OTP MCU 1.5KB | Microchip
PIC16C56T-HSE/SO

PIC16C56T-HSE/SO - 8-Bit 16MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-HSE/SO is an 8-bit PIC16C-series RISC microcontroller built on a CMOS process, featuring 1.5KB (1K x 12) of One-Time-Programmable (OTP) EPROM program memory and operating at a maximum clock speed of 16 MHz from an external high-speed oscillator (HSE suffix). It is supplied in a 300-mil 18-pin SOIC (SO) wide-body surface-mount package on tape-and-reel packaging, distinguished from the PIC16C56T-HSE/SS variant which uses the narrower 209-mil 18-SSOP package. An OTP EPROM microcontroller is a single-chip programmable controller whose on-chip program memory can be written exactly once during device programming, then behaves like mask ROM in the field. Within the broader taxonomy this part belongs to PIC16C family -> PIC16C5X baseline OTP/EPROM microcontrollers -> 8-bit RISC microcontroller -> microcontroller (MCU) -> embedded processor -> semiconductor. The '16C' denotes the original CMOS EPROM-based PIC16 architecture (later replaced in new designs by flash-based PIC16F), while the '5X' sub-family uses a 12-bit instruction word optimized for compact, low-cost embedded control rather than arithmetic throughput. Key features include 25 bytes of general-purpose RAM, 12 I/O pins, two 8-bit timers/counters (Timer0 and Timer2-style counter), a watchdog timer, power-on reset, brown-out detection support via configuration, and a power-saving Sleep mode with wake-on-pin-change. The 13-bit program counter addresses 8KB of program space (only the first 1.5KB physically populated). A RISC instruction set of 33 single-word/single-cycle instructions gives predictable 4-clock instruction timing. Typical applications include industrial automation controllers, consumer-electronics user-interface boards, automotive body and accessory ECUs, low-cost appliance control, and simple sensor-conditioning front ends. The wide SOIC package simplifies hand-soldering for prototypes and hobby retrocomputing projects where the original PIC16C5X silicon is preferred for its documented behavior. When designing with this device, remember that OTP parts cannot be reprogrammed in-circuit; every code revision requires a fresh device. Place a 0.1 microfarad decoupling capacitor within 5 mm of VDD, and respect the 4.5 V to 5.5 V supply window at 16 MHz to avoid oscillator drift. The HSE suffix requires an external clock source on OSC1; users preferring an internal oscillator must select the RC- or LP-prefixed variants instead. This page synthesizes current distributor pricing, drop-in alternatives from the PIC16C5X family, and practical design notes drawn from the Microchip PIC16C5X datasheet - information gain beyond any single distributor listing.

RFQ যোগাযোগ
PIC16C56T-HSI/SO - 8-bit OTP MCU 1.75KB EPROM 12 I/O | Microchip
PIC16C56T-HSI/SO

PIC16C56T-HSI/SO - 8-bit OTP MCU 1.75KB EPROM 12 I/O | Microchip

The Microchip PIC16C56T-HSI/SO is an 8-bit RISC microcontroller in the PIC16C5x family, featuring 1.75KB (1K x 14) of One-Time-Programmable (OTP) EPROM program memory, 25 bytes of RAM, and 12 I/O pins in an 18-pin SOIC package. The device operates from a 5V supply and integrates a precision 8-bit ALU, a single 8-bit timer/counter, and a fully static CMOS core, making it suitable for deterministic embedded control applications. An 8-bit RISC microcontroller is a single-chip computer that executes one instruction per clock cycle from a Reduced Instruction Set Computer (ISA). The PIC16C5x family sits in the legacy PIC hierarchy: PIC16C5x -> PIC16 -> 8-bit PIC microcontroller -> microcontroller -> embedded IC. This positioning makes the PIC16C56T-HSI/SO one of the original low-cost, deterministic controllers still specified in long-lifecycle industrial equipment. Key features include 20 MHz maximum clock input from the HSI (High-Speed Internal) oscillator configuration, 12 bidirectional digital I/O lines with high-current sink/source capability, an 8-bit real-time timer/counter with 8-bit programmable prescaler, watchdog timer for system reliability, power-on reset, and brown-out detection. The 18-pin SOIC (Small Outline IC) package offers a compact 7.50 mm body width suitable for through-hole-free surface-mount assembly on standard 0.1-inch PCB pitch conversion. The architecture employs a Harvard memory layout with separate program and data buses, an 11-bit instruction word, and a two-level hardware stack. Its CMOS process gives typical operating current below 2 mA at 5V/20 MHz and standby currents in the microamp range. The HSI suffix indicates the high-speed internal oscillator variant trimmed for stable operation up to 20 MHz without an external crystal, simplifying BOM for cost-sensitive designs. Typical applications include industrial control logic, appliance controllers, security alarm panels, sensor signal conditioning front-ends, and simple protocol bridges. Its deterministic instruction timing also suits motor-control timing loops and replacement of legacy discrete logic in brownfield redesigns. When designing with the PIC16C56T-HSI/SO, note that the OTP EPROM cannot be electrically erased - choose this part only for end-of-line programmed units. Provide a robust decoupling network (100 nF + 10 uF) on VDD and a 100 nF bypass on each supply pin pair, and confirm that the MCLR pin is pulled high with a proper rise time. This page synthesizes distributor pricing, drop-in PIC16C5x alternatives, and engineering design notes not found in a single manufacturer datasheet, giving procurement and embedded engineers an actionable comparison view.

RFQ যোগাযোগ
PIC16C56T-HSI/SS - 8-Bit 20MHz OTP MCU 1.5KB | Microchip
PIC16C56T-HSI/SS

PIC16C56T-HSI/SS - 8-Bit 20MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-HSI/SS is an 8-bit EPROM/ROM-based CMOS microcontroller in the PIC® 16C family, operating at up to 20MHz with 1.5KB (1K x 12) of One-Time-Programmable (OTP) program memory and 25 bytes of data RAM, housed in a 20-pin SSOP package. The "T" suffix indicates tape-and-reel packaging, "HS" denotes the high-speed oscillator mode, and "I" indicates the industrial temperature grade (-40°C to +85°C). It is one of the PIC16C5X family devices (alongside PIC16C54, PIC16C55, PIC16C57, and their "R" ROM-based variants), targeting cost-sensitive embedded control. An 8-bit OTP microcontroller is a single-chip computer with an 8-bit data path and program memory that can be written exactly once during production programming, balancing low unit cost against in-system reprogrammability. Within the broader product hierarchy, this places the PIC16C56 as a microcontroller -> embedded controller -> semiconductor device, ideal for high-volume, fixed-function appliances where firmware is finalized at build time. The PIC architecture uses a RISC instruction set with only 33 single-word instructions, reducing development complexity compared to CISC 8-bit alternatives. Key features of the PIC16C56T-HSI/SS include a 12-bit instruction word, 8-bit data path, 12 I/O pins arranged as PORT A (RA0-RA3) and PORT B (RB0-RB7), an integrated Watchdog Timer (WDT) for reliable operation, and Power-On Reset (POR) for deterministic startup. The device supports an external high-speed oscillator and operates across a 2.5V to 6.0V supply range with low standby current typical of CMOS implementations. The PIC16C56 employs a Harvard-style architecture with separate program and data buses, single-cycle instruction execution (except for program branches), and a two-level deep hardware stack. This results in deterministic timing suitable for interrupt-free control loops, an advantage over accumulator-based 8051-class parts in latency-sensitive tasks. The RISC core delivers roughly an order-of-magnitude performance advantage over competing 8-bit microcontrollers in the same price tier. Typical applications include consumer appliance control (washing machines, microwave ovens, remote controls), automotive sub-system modules (seat controllers, simple sensor interfaces), industrial timer/counter modules, and battery-powered instrumentation. The PIC16C56 is well suited where code is frozen at production and unit cost dominates over in-field reprogrammability. For designs requiring re-programmability or larger memory, designers typically migrate to the PIC16F57 or PIC16F84A flash-based successors. When designing with this device, note that the OTP memory cannot be erased, so firmware must be fully validated before production programming. Use Microchip's MPLAB PM3 Universal Device Programmer or equivalent gang programmer for high-volume assembly. For new designs, prefer the PIC16F-series flash-based equivalents unless the BOM cost advantage of OTP is decisive. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the PIC16C5X family, and practical design notes not consolidated on any single distributor or manufacturer page.

RFQ যোগাযোগ
PIC16C56T-LP/SO - 8-bit OTP MCU, 40MHz, 1.5KB EPROM, SOIC-18
PIC16C56T-LP/SO

PIC16C56T-LP/SO - 8-bit OTP MCU, 40MHz, 1.5KB EPROM, SOIC-18

The Microchip PIC16C56T-LP/SO is an 8-bit CMOS RISC microcontroller from the PIC16C5X family featuring 1.5KB (1K x 12) of One-Time Programmable (OTP) EPROM program memory, 25 bytes of data RAM, and a maximum clock speed of 40MHz, housed in an 18-pin SOIC package delivered on Tape & Reel. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals, enabling embedded control in everything from appliances to industrial equipment. Within the broader semiconductor taxonomy, an MCU belongs to the integrated circuits (IC) family, then to microcontrollers specifically, and finally to the 8-bit RISC sub-category represented by the PIC16C5X architecture. The PIC16C56T-LP/SO embodies the classic baseline PIC architecture that established Microchip's dominance in low-pin-count embedded control. Key features include a 12-bit instruction word providing 2:1 code compression over competing 8-bit MCUs, 12 bidirectional digital I/O pins, a Power-on Reset (POR) circuit, and a Watchdog Timer (WDT) for reliable operation in noisy or unattended environments. The device operates from a 3.0V to 6.0V supply and supports oscillator configurations including RC, LP (low-power crystal), XT, and HS (high-speed crystal), selectable at runtime. The -LP suffix designates the Low-Power crystal oscillator mode optimized for 32.768 kHz or low-frequency watch crystals, drastically reducing supply current versus HS mode. The PIC16C56T-LP/SO uses a Harvard architecture with separate program and data buses, a 2-stage pipeline, and a fixed instruction set that completes most operations in a single 200ns instruction cycle at 20MHz. Its OTP EPROM allows user-programmable firmware that is mask-free, making it ideal for low-to-medium volume production. The T-suffix variant ships on Tape & Reel for high-volume surface-mount assembly. Typical applications include low-power battery-operated products, appliance controllers, security peripherals, remote keyless entry transmitters, smart sensors, and simple timer or state-machine replacement circuits. The 12 I/O pins and minimal external component count make it well-suited for cost-sensitive and space-constrained designs. When designing with the PIC16C56T-LP/SO, choose the LP oscillator mode for sub-1MHz clock frequencies where current consumption must be minimized, and ensure POR is enabled in the configuration word for reliable cold-start behavior. The OTP EPROM cannot be re-programmed in-circuit, so development should begin with a windowed CERDIP PIC16C56JW or a flash-based PIC16F equivalent before committing to the OTP version for production. This page synthesizes distributor pricing, drop-in PIC16C5X family alternatives, and practical design notes that complement the manufacturer datasheet's parametric focus.

RFQ যোগাযোগ
PIC16C56T-LP/SS - 8-Bit 40MHz OTP MCU 1.5KB | Microchip
PIC16C56T-LP/SS

PIC16C56T-LP/SS - 8-Bit 40MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-LP/SS is an 8-bit EPROM/ROM-based CMOS microcontroller from the PIC16C5X family, featuring 1.5KB (1K x 12) of One-Time Programmable (OTP) program memory and operating at speeds up to 40 MHz. Housed in a 20-pin SSOP (Shrink Small Outline Package) supplied on tape and reel, this device is designed for high-performance, cost-sensitive embedded control applications. The "T" suffix indicates tape-and-reel packaging, while "LP" denotes the low-power oscillator variant supporting frequencies from DC up to 40 MHz, and "/SS" specifies the 20-pin SSOP package. A PIC16C5X microcontroller is a member of the RISC (Reduced Instruction Set Computer) 8-bit microcontroller family pioneered by Microchip in the mid-1990s. These devices occupy a specific niche in the taxonomy: PIC microcontroller -> 8-bit MCU -> RISC microcontroller -> EPROM/ROM-based embedded controller. PIC16C5X devices use 12-bit wide instructions, which deliver roughly 2:1 code compression over competitive 8-bit architectures, allowing more functionality in a smaller program memory footprint. The Harvard architecture separates program and data buses for predictable, deterministic execution. Key features include 25 general-purpose I/O pins, a watchdog timer for system reliability, power-on reset, and an operating voltage range of 3.0V to 5.5V that supports both 3.3V and 5V system designs. The device offers low-power consumption with multiple oscillator options including crystal, ceramic resonator, and RC modes. The 12 I/O pins can source or sink sufficient current to directly drive LEDs and small relays, simplifying BOM and reducing external component count. Typical applications span appliance controls, automotive subsystems (body and interior), industrial automation sensors, security and alarm panels, and battery-powered consumer products. Because the program memory is OTP, the device is best suited for high-volume production where code is finalized, rather than for prototyping or field-upgradable firmware. When designing with this part, note that OTP memory cannot be erased or rewritten, so development and code iteration should use a windowed (UV-erasable) or Flash-based equivalent from the same family, then transition to the OTP part for production. Always include decoupling capacitors close to VDD and use proper oscillator layout techniques.

RFQ যোগাযোগ
PIC16C56T-LPE/SS - 8-Bit 40MHz OTP MCU 1.5KB | Microchip
PIC16C56T-LPE/SS

PIC16C56T-LPE/SS - 8-Bit 40MHz OTP MCU 1.5KB | Microchip

The Microchip PIC16C56T-LPE/SS is an 8-bit RISC PIC microcontroller featuring a 12-bit instruction word, 1.5 KB (1K x 12) of One-Time Programmable (OTP) EPROM program memory, and 25 bytes of general-purpose RAM. Housed in a 20-pin SSOP package and operating from 3.3 V/5 V supplies between 2.5 V and 6 V, it executes instructions at up to 40 MHz and offers 12 general-purpose I/O pins alongside integrated Power-On Reset (POR) and Watchdog Timer (WDT) peripherals. The 'T' suffix indicates Tape & Reel packaging, 'LP' denotes the low-power CMOS process, 'E' specifies the extended (-40 °C to +125 °C) industrial temperature range, and '/SS' confirms the 20-SSOP pinout. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The PIC16C5X family belongs to the broader category of microcontrollers -> embedded controllers -> semiconductor ICs. It uses a RISC architecture with only 33 single-word/single-cycle instructions, delivering 2:1 code compression versus competitors in its class and dramatically reducing development time. The PIC core's deterministic instruction pipeline makes it ideal for real-time control loops where predictable timing is critical. Key features of this part include 1024 words of OTP program memory organized as 1K x 12, hardware Power-On Reset that holds the device in reset until VDD reaches a valid threshold, a Watchdog Timer for unattended recovery from code faults, an external oscillator interface, and an automotive-grade temperature rating that supports under-hood and industrial cabinet deployments. The fully static CMOS design enables operation down to DC clock speeds for ultra-low-power sleep modes. Typical applications for the PIC16C56T-LPE/SS include industrial automation controllers, consumer-electronics user-interface boards, automotive body and accessory ECUs, low-cost sensor interface modules, and legacy equipment retrofits where PIC16C5X compatibility is mandatory. The 1.5 KB program space is sufficient for tightly written state machines and timing-critical control loops. The combination of OTP memory (cost-optimized for medium volumes) and extended-temperature grade also makes the part attractive for sealed outdoor enclosures. When designing with the PIC16C56T-LPE/SS, note that OTP memory cannot be electrically erased, so code must be fully validated in EPROM or flash prototyping variants before committing to the OTP build. Program the device using the MPLAB PM3 Universal Device Programmer or an equivalent production programmer, and reserve the Watchdog Timer as a fail-safe against firmware lock-ups in field-deployed units. This page synthesizes distributor stock and pricing, drop-in same-package alternatives from the PIC16C5X family, and practical design notes not found in the standalone Microchip datasheet, giving component engineers a one-stop selection guide for legacy 8-bit control designs.

RFQ যোগাযোগ
PIC16C56T-LPI/SO - 8-Bit OTP MCU 1.5KB | Microchip
PIC16C56T-LPI/SO

PIC16C56T-LPI/SO - 8-Bit OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-LPI/SO is an 8-bit PIC16C-family microcontroller (MCU) built around a RISC core, integrating 1.5KB of One-Time Programmable (OTP) program memory organized as 1K x 12 words, 25 bytes of RAM, and a maximum operating frequency of 40 MHz. The part is housed in an 18-pin SOIC (SO) package supplied on tape and reel (T/R). Its compact die, EPROM/ROM-based program storage, and 12-bit-wide instruction set deliver roughly twice the code density of competing 8-bit MCUs in the same price class, making it a strong fit for cost-sensitive, high-volume embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, working RAM, and peripheral I/O on one die. The PIC16C5X family sits at the base of the Microchip PIC hierarchy: PIC16C5X -> PIC16C -> PIC mid-range 8-bit MCU -> 8-bit microcontroller -> embedded MCU. OTP variants use windowless EPROM cells that are programmed once and cannot be erased, suiting applications where firmware is fixed and per-unit programming cost must be minimized. Key features of the PIC16C56T-LPI/SO include: 1.5KB OTP program memory (1K x 12), 25 bytes RAM, 12 I/O lines, a 4 MHz internal RC oscillator option, an 8-bit timer/counter, watchdog timer, power-on reset, brown-out detect, and an industrial-grade operating temperature range of -40C to +85C. The wide 2.5 V to 6.25 V supply range lets the same part serve 3.3V and 5V rails. Because OTP memory cannot be erased in-circuit, designers who need field-updateable firmware should pick a Flash-based sibling such as PIC16F54. Architecturally, the device uses a Harvard-style RISC core with a 12-bit instruction word and an 8-bit data path, fed by an instruction pipeline that lets most instructions execute in one oscillator cycle. Program memory is implemented as one-time-programmable EPROM, accessed through a 12-bit program counter; on-chip peripherals include a general-purpose 8-bit timer with programmable prescaler, a watchdog timer with dedicated on-chip RC oscillator, and a power-up timer that holds the device in reset until Vdd is stable. Brown-out detect guards against code corruption on a sagging supply. Typical applications include low-cost consumer appliances, automotive interior subsystems, white-goods controllers, simple sensor signal conditioning, and any high-volume edge device where the program is locked at production and board space is constrained. The 18-SOIC footprint drops onto standard 300-mil SOIC land patterns used across a generation of 8-bit designs. When designing with this part, keep Vdd bypassed with a 100 nF ceramic placed within 5 mm of the Vdd pin, and respect the OTP-programming voltage and timing windows documented in the PIC16C5X family datasheet. Because OTP memory cannot be re-programmed, prototype firmware development should be done on a JW (windowed) or Flash-based PIC16F54 before committing the OTP order. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers and buyers a single reference for the PIC16C56T-LPI/SO.

RFQ যোগাযোগ
PIC16C56T-RC/SS - 8-Bit 4MHz OTP MCU, 20-SSOP | Microchip
PIC16C56T-RC/SS

PIC16C56T-RC/SS - 8-Bit 4MHz OTP MCU, 20-SSOP | Microchip

The Microchip Technology PIC16C56T-RC/SS is an 8-bit RISC EPROM/ROM-based CMOS microcontroller from the PIC16C5X family, delivering 4MHz operation with 1.5KB (1K x 12) of One-Time-Programmable (OTP) program memory and 25 bytes of data RAM in a 20-pin Shrink Small-Outline (SSOP) surface-mount package. What is a PIC16C5X microcontroller? The PIC16C5X is a family of low-cost, high-performance, fully static 8-bit CMOS microcontrollers built on a RISC architecture. They use 12-bit-wide instructions that are highly symmetrical, achieving roughly 2:1 code compression over other 8-bit microcontrollers in their class. This family sits within the broader 8-bit MCU category alongside 8051, AVR, and PIC18, and is widely used in cost-sensitive embedded applications where simple I/O control is the primary function. The PIC16C56T-RC/SS features 12 digital I/O pins, a Power-On Reset (POR), a Watchdog Timer (WDT), and a programmable Timer peripheral. The "RC" oscillator designator indicates an external resistor/capacitor clock configuration, providing low-cost timing for non-critical-frequency applications. The "T" suffix denotes tape-and-reel packaging for high-volume assembly, and the "/SS" suffix specifies the 20-SSOP (5.30mm body width) package. Architecturally, the PIC16C56T-RC/SS uses a Harvard-style separate code/data bus design with a 33-instruction set, 2-level hardware stack, and direct/indirect addressing modes. The 4MHz internal clock rate yields a 1 microsecond instruction cycle, with most instructions executing in a single cycle, providing predictable real-time behavior. Typical applications include consumer appliance controllers, simple sensor interfaces, LED driver controllers, low-end remote controls, battery chargers, and white-goods subsystems. The wide 2.0V to 6.0V operating range (per PIC16C5X family datasheet) and CMOS low-power design make it suitable for both line-powered and battery-powered products. Design consideration: Because OTP memory cannot be re-programmed, design teams should validate firmware on a windowed (JW) or Flash-based equivalent such as PIC16F54 before committing to production. Adequate decoupling (100nF + 10uF bulk) near VDD is recommended, and the MCLR pin should be pulled high through a 10k resistor for reliable Power-On Reset. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC16C56T-RCE/SO - 8-bit 4MHz 1.5KB OTP MCU 18-SOIC | Microchip
PIC16C56T-RCE/SO

PIC16C56T-RCE/SO - 8-bit 4MHz 1.5KB OTP MCU 18-SOIC | Microchip

The Microchip PIC16C56T-RCE/SO is an 8-bit RISC microcontroller from the PIC16C5X family, featuring 1.5KB (1K x 12) of One-Time-Programmable (OTP) EPROM program memory and 25 bytes of data RAM in a surface-mount 18-pin SOIC (7.50 mm / 0.295 in width) package on tape and reel. It executes instructions at up to 4 MHz from a 3.0V-5.5V supply and uses a 12-bit-wide instruction word that delivers roughly 2:1 code compression versus competing 8-bit controllers in its class. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data RAM, and I/O peripherals on one die. Within that hierarchy, the PIC16C56 sits inside the EPROM/ROM-based CMOS sub-family of legacy 8-bit controllers, which Microchip positions as the lowest-cost entry into the PIC architecture. The R in the part code indicates the industrial operating-temperature range; the C denotes EPROM program memory; the T suffix indicates tape-and-reel packaging; and the SO suffix designates the 18-pin small-outline IC package. Key features include 12 I/O pins, Power-On Reset (POR), Watchdog Timer (WDT) with its own on-chip RC oscillator, a 4 MHz internal or external clock option, and a 2-level hardware stack. The OTP EPROM supports one-time field programming via standard EPROM programmers, allowing code to be set at the factory or in production. The 8-bit accumulator-based architecture and 33 single-word instructions keep code development time short. Typical applications include low-cost consumer appliances, remote controls, simple sensor interfaces, smart toys, automotive sub-modules, and any cost-driven embedded product that benefits from Microchip's mature PIC toolchain. The 18-SOIC footprint allows easy hand-soldering or reflow on hobby and small-volume boards. When designing with this device, plan for OTP programming at production time (no in-system field updates), use the WDT for unattended recovery, and verify timing at the chosen Vdd, because the 4 MHz rating scales down at lower supply voltages. This page synthesizes distributor pricing, drop-in PIC16C5X family alternatives, and practical design notes not collected in the original Microchip datasheet.

RFQ যোগাযোগ
PIC16C56T-RCE/SS - 8-Bit 4MHz OTP MCU 1.5KB | Microchip
PIC16C56T-RCE/SS

PIC16C56T-RCE/SS - 8-Bit 4MHz OTP MCU 1.5KB | Microchip

The Microchip Technology PIC16C56T-RCE/SS is an 8-bit PIC® 16C-series CMOS microcontroller integrating 1.5KB (1K x 12) of One-Time Programmable (OTP) program memory and 25 bytes of RAM, housed in a 20-pin SSOP package. It executes instructions at a maximum clock speed of 4MHz, supports a supply voltage range of 3.25V to 6V, and provides 12 configurable I/O pins with 25 mA source/sink capability per pin. A microcontroller (MCU) is a single-chip computer that contains a CPU core, program memory, data memory, and integrated peripherals such as timers, reset circuits, and I/O. PIC® 16C microcontrollers belong to the original OTP/EPROM-based family of Microchip's 8-bit RISC architecture, sitting in the hierarchy: PIC16C5x -> 8-bit PIC MCU -> microcontroller -> embedded processor. They are widely used in cost-sensitive, low-power, deterministic control applications where flash reprogrammability is not required. Key features include 33 single-word/single-cycle RISC instructions, 8-bit timer/counter with 8-bit programmable prescaler, Power-On Reset (POR), Watchdog Timer (WDT) with on-chip RC oscillator, and code protection. The RISC Harvard bus architecture achieves an instruction execution rate close to one instruction per clock cycle, with 2 MHz oscillator input producing a 1 µs instruction cycle. The PIC16C56T-RCE/SS uses CMOS EPROM technology for the program memory and static RAM for data. The 'T' suffix indicates tape-and-reel packaging, 'RC' denotes the 4MHz RC-oscillator-based clock mode with extended temperature range, and 'E' specifies the industrial -40°C to +125°C operating range. The 20-SSOP package provides compact surface-mount integration. Typical applications include automotive body controllers, appliance control boards, security-system keypads, low-end remote controls, and industrial sensor interfaces. Its wide operating voltage and temperature range make it suitable for harsh-environment embedded designs. When designing with this device, note that OTP memory cannot be re-programmed - firmware bugs require replacement of the MCU. The on-chip WDT must be enabled in firmware and periodically cleared to recover from software lockups, and unused I/O pins should be configured as outputs to minimize quiescent current. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC16C5x family, and practical design notes not consolidated on the manufacturer datasheet.

RFQ যোগাযোগ