মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

PIC32MM0256GPM048-I/M4 - 32-bit 256KB Flash USB MCU | Microchip
PIC32MM0256GPM048-I/M4

PIC32MM0256GPM048-I/M4 - 32-bit 256KB Flash USB MCU | Microchip

The Microchip Technology PIC32MM0256GPM048-I/M4 is a 32-bit RISC microcontroller from the eXtreme low power PIC32MM GPM family, featuring a MIPS32 microAptiv core running at up to 25 MHz, 256 KB of ECC-enabled Flash program memory, and 32 KB of SRAM, housed in a 48-pin UQFN (6x6 mm) package with exposed pad. The device operates from 2.0 V to 3.6 V and integrates a USB 2.0 full-speed device transceiver, four-channel DMA, twenty-one timers, three analog comparators, and a 12-bit 200 ksps ADC with up to 28 input channels. The GPM family extends Microchip's lowest-power 32-bit PIC32 line by adding USB 2.0 full-speed support, error-correcting code (ECC) memory, and CoreMark scores up to 79 at 25 MHz, making it a strong fit for connected, energy-conscious embedded designs. A 32-bit microcontroller (MCU) is an integrated circuit that combines a 32-bit CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), and a rich peripheral set on a single silicon die. Within the broader semiconductor taxonomy, the PIC32MM GPM belongs to the category of low-power embedded microcontrollers, sitting between 8/16-bit MCUs and higher-performance application processors. It is widely used in battery-powered and energy-harvesting designs where MIPS-per-watt and deep-sleep current matter more than raw clock speed. Key features include 79 CoreMark at 25 MHz, hardware ECC on Flash to detect and correct single-bit errors, microMIPS and MIPS32 dual instruction modes for code-density flexibility, and multiple low-power modes (Sleep, Idle, Deep Sleep). Serial peripherals cover USB 2.0 full-speed device, up to three I2C, three SPI, and three UART interfaces. The device also integrates a 32 kHz low-power internal RC oscillator suitable for RTC operation, plus a programmable 8 MHz Fast RC oscillator with PLL. Architecturally, the PIC32MM GPM uses a Harvard bus architecture with separate Flash and SRAM paths, supports two-wire ICSP programming/debug (PGEDx/PGECx), and ships with a compact UQFN-48 (6x6 mm) footprint offering 38 general-purpose I/O pins. The integrated USB 2.0 full-speed PHY eliminates the need for an external transceiver for HID, CDC, and other low-speed USB device applications. Typical applications include IoT sensor nodes, low-power wireless modules, USB human-interface devices (HIDs) such as keyboards and mice, consumer electronics, and small medical and industrial sensor designs requiring multi-year battery life. The combination of USB, ECC Flash, and aggressive sleep currents makes this part well-suited for designs balancing communication, reliability, and energy budget. When designing with this MCU, ensure the exposed pad (EP) on the UQFN-48 package is soldered to the ground plane for thermal dissipation and signal integrity. For USB applications, route the D+/D- differential pair with 90 ohm impedance and keep the pair matched within 2 mm. Decouple VDD with 0.1 uF and 1 uF ceramics placed within 3 mm of each supply pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC32MM0256GPM048-I/PT - 25MHz 32-bit MCU, 256KB Flash, USB | Microchip
PIC32MM0256GPM048-I/PT

PIC32MM0256GPM048-I/PT - 25MHz 32-bit MCU, 256KB Flash, USB | Microchip

The Microchip Technology PIC32MM0256GPM048-I/PT is a 32-bit MIPS32 microAptiv PIC microcontroller running at up to 25 MHz with 256 KB of ECC Flash and 16 KB of SRAM, integrated USB 2.0 full-speed device support, and housed in a 48-pin TQFP-EP (7x7 mm) package with exposed thermal pad. It belongs to the eXtreme Low Power (XLP) PIC32MM GPM family that extends Microchip's lowest-power 32-bit MCU line by adding USB and ECC memory up to 256 KB. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, peripherals, and I/O into a single device. Within the taxonomy, the PIC32MM0256GPM048 sits as: 32-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The PIC32MM GPM family uses the MIPS32 microAptiv core, which supports the MIPS16e instruction set for code-density optimization. ECC on Flash detects and corrects single-bit errors in program memory, which improves reliability for industrial and consumer applications. Key features of the PIC32MM0256GPM048-I/PT include a 25 MHz maximum core clock, 256 KB ECC Flash, 16 KB SRAM, 4 KB EEPROM (emulated), USB 2.0 full-speed device, multiple timer/capture-compare/PWM modules, 12-bit 1.1 Msps ADC, multiple UART/SPI/I2C peripherals, and rich touch/analog integration suited for HMI and sensor applications. The -I suffix denotes the -40C to +85C industrial temperature range. The PIC32MM0256GPM048-I/PT uses a 3.3V single supply with multiple power-saving modes targeted at ultra-low active and sleep currents. Its rich peripheral set and USB 2.0 FS device interface make it a cost-effective choice for HID-class devices, sensors, and human-machine interfaces. Typical applications include USB human-interface devices (HID) such as keyboards, mice, and touch panels; low-power IoT sensor nodes; motor-control front ends; consumer appliances with touch UIs; and industrial control systems where low active and sleep power are critical. The integrated USB device peripheral eliminates external PHY chips, reducing BOM cost. When designing with this device, allocate sufficient decoupling (100 nF plus 4.7 uF bulk) near each VDD pin and keep the USB DP/DM traces 90-ohm differential-matched. The exposed thermal pad must be soldered to a grounded copper pour for electrical and thermal performance; omitting it can degrade ESD/EMC behavior. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selecting and implementing the PIC32MM0256GPM048-I/PT.

RFQ যোগাযোগ
PIC32MM0256GPM048T-I/M4 - 256KB Flash 32-bit MCU 48-UQFN | Microchip
PIC32MM0256GPM048T-I/M4

PIC32MM0256GPM048T-I/M4 - 256KB Flash 32-bit MCU 48-UQFN | Microchip

The Microchip PIC32MM0256GPM048T-I/M4 is a 32-bit MIPS32 microAptiv microcontroller from the PIC32MM GPM family, featuring 256 KB Flash and 32 KB RAM in a 48-pin UQFN (6x6 mm) package. It operates at up to 25 MHz core / 48 MHz equivalent microMIPS and integrates USB FS device/host, ECC memory, ADC, DAC, DMA, and a 79 CoreMark performance figure. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripherals such as ADCs, timers, and communication interfaces. In the broader taxonomy, the PIC32MM belongs to 32-bit microcontrollers, which sit above 8-bit MCUs and below microprocessors, and the PIC32MM GPM line targets low-power USB-connected applications where MIPS-class performance is needed without consuming the energy of higher-tier MPU families. Key features include hardware ECC on Flash for improved reliability, deep-sleep current in the microamp range for battery-backed designs, integrated USB 2.0 full-speed transceiver with on-chip pull-ups, and rich analog peripherals: a 12-bit ADC with up to 28 channels, a 10-bit DAC, and comparators. The 48-UQFN (M4) package exposes up to 38 general-purpose I/O pins while keeping the board footprint at 6x6 mm, ideal for space-constrained USB dongles, sensor hubs, and human-interface devices. Architecturally, the PIC32MM GPM uses the MIPS M4K-based microAptiv core running the microMIPS instruction set, which compresses common instructions to 16 bits while retaining 32-bit register width. This delivers higher code density than ARM Cortex-M0+ at similar MHz, while peripheral DMA moves ADC and USB traffic off-core for predictable latency. Typical applications include USB human-interface devices (HID keyboards, mice, game controllers), low-power IoT sensor nodes with USB charging, industrial control panels requiring ECC memory, and consumer audio peripherals using the on-chip DAC. The 256 KB Flash is sufficient for USB stacks, vendor class drivers, and rich application logic in a single chip. When designing with this device, allocate adequate decoupling near the VDD pins and route the USB DP/DM pair as a 90 ohm differential. The UQFN exposed pad must be soldered to a sufficient copper pour for thermal dissipation; operating from a regulated 3.3 V rail is recommended to stay within the 2.0-3.6 V VDD spec. This page synthesizes distributor pricing from DigiKey/Mouser/Arrow, drop-in alternatives in the same 48-UQFN footprint, and practical design notes not duplicated in the manufacturer datasheet - use it to shortlist candidates and shorten your schematic-to-prototype cycle.

RFQ যোগাযোগ
PIC32MM0256GPM048T-I/PT - 32-bit 25MHz 256KB MCU 48-TQFP | Microchip
PIC32MM0256GPM048T-I/PT

PIC32MM0256GPM048T-I/PT - 32-bit 25MHz 256KB MCU 48-TQFP | Microchip

The Microchip Technology PIC32MM0256GPM048T-I/PT is a 32-bit MIPS32 microAptiv PIC microcontroller operating at up to 25 MHz, integrating 256 KB of Flash and 32 KB of SRAM into a 48-pin TQFP-EP (7x7 mm) package with an exposed thermal pad. It is part of the eXtreme low power PIC32MM GPM family and runs from a 2.0V to 3.6V supply. The part combines a fast deterministic core, a USB 2.0 Full-Speed device/host/OTG controller, and Error-Correcting Code (ECC) memory for robust industrial and consumer designs. A microcontroller (MCU) is a single-chip computer that combines a CPU, memory and programmable peripherals into a single IC; the PIC32MM family belongs to the broader 32-bit MCU taxonomy (32-bit MCU -> RISC microcontroller -> embedded controller -> semiconductor IC) and is purpose-built for low-power mixed-signal applications. The microAptiv core implements the MIPS32 instruction set with hardware multiply/divide and a Memory Management Unit-like configuration, giving it deterministic interrupt latency for real-time control. The on-chip 32 KB SRAM is ECC-protected against soft errors, while the 256 KB Flash supports live update and a configurable Prefetch module that lets the core execute from Flash with zero wait state on most accesses. Key differentiating features include: 4-channel hardware DMA, a 12-bit ADC with up to 24 channels and 200 ksps throughput, three 16-bit timers/captures/PWMs, up to nine CCP/SCCP modules, an integrated USB 2.0 FS transceiver that eliminates external PHY cost, and configurable peripherals that allow pin-mapping remap. The device supports multiple serial interfaces including UART, SPI (3-wire/4-wire/Quad-SPI optional), I2C and I2S, along with PMP/EPMP for parallel display or memory buses. Power-saving features include Deep Sleep, Sleep, Idle and Peripheral Module Disable modes that drive quiescent consumption into the microampere range. Typical applications include USB HID peripherals such as PC gaming mice/keyboards, low-cost IoT sensor nodes, cost-optimized consumer appliances, industrial data loggers, and small-color graphics HMI with parallel display. The USB OTG capability lets designers build dual-role devices (e.g., USB-C chargers, debug bridges) without adding a USB IC, while the 256 KB flash accommodates a full TCP/IP or USB stack plus application code. Design trade-off: although the PIC32MM GPM provides strong low-power behavior, designers migrating from PIC32MX should confirm that their existing firmware uses the Harmony configurator (PMSM, ICSP) projects. The exposed thermal pad (EP) must be soldered for thermal and electrical reference - failing to do so derates power performance and may cause latch-up under high-current loads.

RFQ যোগাযোগ
PIC32MM0256GPM064-E/MR - 32-bit 25MHz 256KB Flash MCU | Microchip
PIC32MM0256GPM064-E/MR

PIC32MM0256GPM064-E/MR - 32-bit 25MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC32MM0256GPM064-E/MR is a 32-bit MIPS32 microAptiv UC core microcontroller running up to 25 MHz with 256 KB ECC Flash and 32 KB SRAM, housed in a 64-pin 9x9 mm QFN package with exposed pad. It belongs to the PIC32MM GPM "eXtreme Low Power" family and operates from 2.0 V to 3.6 V with on-chip ECC-protected memory and integrated USB 2.0 full-speed support. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, ADC, communication interfaces (UART, SPI, I2C), and I/O pins. The PIC32MM family is positioned in the hierarchy: 32-bit MCU -> MIPS32 microAptiv core -> PIC32 family -> PIC32MM GPM family -> Microchip 32-bit microcontrollers. MCUs execute embedded firmware to sense, control, and communicate in real time, distinguishing them from microprocessors which require external memory and peripherals. Key features of the PIC32MM0256GPM064-E/MR include 256 KB Flash with Error-Correcting Code (ECC) for high-reliability applications, 32 KB SRAM, 52 general-purpose I/O pins, a 12-bit ADC with up to 200 ksps, multiple PWM/timer modules, I2C/SPI/UART peripherals, USB 2.0 full-speed device/host/OTG, and a Real-Time Clock Calendar (RTCC). The part ships in the extended (-40C to +125C) temperature grade designated by the "-E" suffix and is offered in tube packaging ("MR" = QFN). Architecturally, the PIC32MM0256GPM064-E/MR leverages the MIPS32 microAptiv UC core with 16 KB instruction cache and a single-cycle 32x32 hardware multiplier, delivering high code-density performance per MHz. Hardware ECC on Flash reduces soft-error-induced failures in long-lifecycle deployments, and the integrated USB PHY eliminates external transceiver BOM. The 64-pin QFN-EP provides a low-thermal-resistance path for hot-spot dissipation during peak USB-driven loads. Typical applications include USB-enabled consumer peripherals, low-power IoT sensor nodes with USB debugging, industrial HMI panels, battery-powered data loggers with ECC, USB barcode/RFID readers, and embedded control modules with safety-critical firmware. The combination of XLP sleep currents, USB, and ECC Flash makes the part attractive for medical accessories and instrumentation as well. When designing with this MCU, ensure the exposed pad (EP) of the QFN package is soldered to a sufficiently large copper pour to meet thermal and electrical ground requirements. For USB applications, follow the Microchip ANs on USB PCB layout to maintain 90-ohm differential impedance on D+/D-. This page synthesizes Microchip distributor pricing, same-brand drop-in variants, and practical design guidance not found in the datasheet alone.

RFQ যোগাযোগ
PIC32MM0256GPM064-I/MR - 256KB Flash USB MCU | Microchip
PIC32MM0256GPM064-I/MR

PIC32MM0256GPM064-I/MR - 256KB Flash USB MCU | Microchip

The Microchip PIC32MM0256GPM064-I/MR is a 32-bit MIPS32 microAptiv UC core microcontroller from the eXtreme Low Power PIC32MM GPM family, delivering 25 MHz CPU speed with 256 KB ECC flash and 32 KB SRAM in a 64-pin 9x9 mm QFN package. The device integrates USB 2.0 full-speed OTG, four 16-bit timers, a 12-bit 1.1 Msps ADC, and multiple serial interfaces, while supporting an industrial -40C to +85C operating range. The GPM family extends Microchip's lowest-power 32-bit PIC32 platform with USB connectivity and ECC-protected memory for safety-critical firmware. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripherals on one die, providing embedded control for everything from sensor nodes to motor drives. Within the broader taxonomy, the PIC32MM family sits under 32-bit microcontrollers, which sit under microcontrollers, which sit under microprocessors and finally under semiconductors. The microAptiv UC core used here implements the MIPS32 instruction set with low-power modes that suspend execution while leaving wake sources active, allowing deep-sleep current well below typical Cortex-M0+ designs. Key differentiating features of this part include the 256 KB flash with ECC, USB 2.0 full-speed OTG on-chip PHY, eXtreme Low Power (XLP) Run, Doze and Sleep modes drawing microamp-level standby, Core Independent Peripherals (CIPs) such as Configurable Logic Cells and 16-bit PWM, and a 12-bit 1.1 Msps ADC with up to 19 analog channels. The 64-pin QFN package exposes up to 53 general-purpose I/O pins, three I2C/SPI/UART peripherals, and four 16-bit timers/counters, providing a balanced peripheral mix for sensor aggregation, motor control and human-interface designs. The architecture combines a deterministic 25 MHz / 25 DMIPS MIPS32 core, a multi-vector interrupt controller with 5-cycle latency, and a Peripheral Pin Select (PPS) remapping fabric that lets users reassign digital peripherals to almost any I/O pin, simplifying PCB routing. Memory protection includes hardware flash ECC, a separate boot flash region, and a configuration-word block that enforces fail-safe clock and watchdog defaults at reset. The integrated USB PHY supports device, host and OTG modes and enumerates as CDC, HID, MSD or vendor classes without an external transceiver. Typical applications include USB-connected sensor hubs, IoT edge nodes, low-power motor drives, e-metering peripherals, consumer human-interface devices, and battery-powered medical accessories. The wide operating voltage (2.0 V to 3.6 V) and four flexible PWM channels make the part especially well suited to brushed DC and stepper control loops where deterministic interrupt latency and small standby current both matter. When designing with this part, enable the watchdog and code-protect configuration words during production programming, use the PPS registers to map peripherals away from default pins when the PCB layout demands it, and place the 32.768 kHz secondary crystal on the SOSC pins with proper load capacitance to achieve the deep-sleep current budget. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for selecting, sourcing, and substituting the PIC32MM0256GPM064-I/MR.

RFQ যোগাযোগ
PIC32MM0256GPM064-I/PT - 32-bit 25MHz 256KB Flash MCU | Microchip
PIC32MM0256GPM064-I/PT

PIC32MM0256GPM064-I/PT - 32-bit 25MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC32MM0256GPM064-I/PT is a 32-bit MIPS32 microAptiv UC core microcontroller running at 25 MHz, integrating 256 KB of ECC Flash and 32 KB of SRAM in a 64-pin TQFP (10x10 mm) package. It belongs to the PIC32MM GPM eXtreme low-power family and includes an integrated USB 2.0 full-speed controller, hardware ECC on Flash, 4 KB EEPROM, and 5V-tolerant I/O on most pins for robust low-cost embedded designs. What is a PIC32MM GPM microcontroller? PIC32MM is Microchip's lowest-power 32-bit MCU family built on the MIPS microAptiv UC core, sitting in the taxonomy: microcontroller -> 32-bit MCU -> MIPS core MCU -> PIC32 family -> PIC32MM GPM. The GPM sub-family adds USB and ECC to the cost-optimized PIC32MM line, making it suitable for cost-sensitive applications that still require certified USB stacks and memory integrity for safety-critical firmware. Key features of the PIC32MM0256GPM064-I/PT include 256 KB program Flash with ECC, 32 KB SRAM, 4 KB EEPROM, a 10-bit 300 ksps ADC with up to 28 channels, four comparators, four I2C, four SPI, four UART, and a USB 2.0 full-speed device/host/OTG controller. The device supports 5V tolerant I/O on most pins and runs from 2.0V to 3.6V. Its eXtreme Low Power (XLP) modes deliver deep-sleep currents in the sub-microamp range, extending battery life in always-on sensor products. The microAptiv UC core implements the MIPS32r2 instruction set with a hardware multiply/divide unit and a single-cycle MAC, enabling DSP-like math at 25 MHz without external accelerators. Internal peripherals route through Microchip's PPS (Peripheral Pin Select) matrix, simplifying PCB layout by allowing digital peripheral functions to be mapped to a wide choice of physical pins and reducing the need for rework. Typical applications include USB HID devices, low-power sensor nodes with USB charging, consumer appliances with capacitive touch, building automation HMI panels, and portable medical peripherals. The integrated USB controller eliminates the need for an external bridge IC in USB-to-UART or USB-to-SPI bridges, lowering BOM cost and board area. When designing with this part, ensure the USB VBUS rail is decoupled per the USB 2.0 specification and that the 48 MHz USB clock accuracy is within +/-0.25% to comply with USB full-speed timing. Use the PPS feature to route peripheral I/O to convenient pins and keep trace lengths short on the USB DP/DM differential pair. This page synthesizes distributor pricing, verified same-brand and cross-brand drop-in alternatives in the 64-pin TQFP package, parametric comparison tables, and practical low-power design notes - information not collected in a single place in the manufacturer datasheet.

RFQ যোগাযোগ
PIC32MX110F016B-I/ML - 32-bit 40MHz MCU, 16KB Flash | Microchip
PIC32MX110F016B-I/ML

PIC32MX110F016B-I/ML - 32-bit 40MHz MCU, 16KB Flash | Microchip

The Microchip Technology PIC32MX110F016B-I/ML is a 32-bit MIPS32 M4K microcontroller running up to 40 MHz with 16 KB Flash and 4 KB SRAM, packaged in a 28-pin 6x6 mm QFN with an exposed thermal pad (ML). It operates from 2.3 V to 3.6 V and is qualified for the industrial -40C to +105C temperature range. A microcontroller (MCU) is a programmable system-on-a-chip that integrates a CPU core, memory, peripherals, and I/O into a single device. PIC32MX MCUs sit in the broader hierarchy of embedded microcontrollers -> 32-bit MCUs -> MIPS-based MCUs -> Microchip PIC32 family -> semiconductor IC. They are designed to deliver deterministic real-time control with higher throughput than 8/16-bit parts while retaining the peripheral-rich architecture familiar to PIC users. Key features of the PIC32MX110F016B include Peripheral Pin Select (PPS) for flexible pin assignment, two I2S/SPI modules for codec and serial connectivity, a Parallel Master Port (PMP) for graphics interfaces, a Charge Time Measurement Unit (CTMU) supporting mTouch capacitive touch buttons/sliders, four DMA channels, and a 10-bit ADC capable of up to 1 Msps. The MIPS32 M4K core delivers 1.56 DMIPS/MHz and executes most instructions in a single cycle, making it suitable for control loops and modest DSP-style signal processing. Typical applications include consumer electronics with graphical displays, capacitive touch human-machine interfaces, USB/audio accessories, sensor hubs, industrial control nodes, and low-cost IoT endpoints that need 32-bit performance without the cost of Cortex-M parts. The 28-QFN footprint suits space-constrained PCB designs such as wearable bands and remote-control modules. When designing with the PIC32MX110F016B-I/ML, ensure the exposed pad is soldered to a sufficient copper pour for thermal and electrical grounding, and respect the supply-voltage range of 2.3 V to 3.6 V across all operating modes including programming. Use MPLAB X IDE with XC32 compiler for development; ICD programming requires dedicated PGECx/PGEDx pin pairs and decoupling on every VDD pin. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes curated for engineers selecting a 28-QFN 32-bit MCU, going beyond the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC32MX110F016B-I/SO - 32-bit MCU, 40 MHz, 16 KB Flash, 28-SOIC | Microchip
PIC32MX110F016B-I/SO

PIC32MX110F016B-I/SO - 32-bit MCU, 40 MHz, 16 KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC32MX110F016B-I/SO is a 32-bit RISC microcontroller based on the MIPS32 M4K core, delivering up to 40 MHz CPU performance in a 28-pin SOIC package. The part integrates 16 KB of Flash program memory and 4 KB of SRAM, with peripheral features including up to 10 channels of 10-bit ADC, four DMA channels, two I2S/SPI modules, and a Charge Time Measurement Unit (CTMU) for capacitive touch sensing via mTouch. Operating voltage is 2.3 V to 3.6 V with industrial temperature range of -40 °C to +105 °C. A microcontroller (MCU) is a single-chip computer that contains a processor core, program memory (Flash), working memory (RAM), and a configurable set of peripherals such as ADC, timers, and communication interfaces. Within the broader semiconductor hierarchy, MCUs sit between microprocessors (which require external memory) and System-on-Chip (SoC) devices (which integrate radio and application-specific accelerators). The PIC32MX family is Microchip's mid-range 32-bit MCU line, positioned above the 16-bit PIC24F and below the higher-pin-count PIC32MZ families. Key differentiators of this device include Peripheral Pin Select (PPS) for remapping most digital peripherals to any I/O, a Parallel Master Port (PMP) for graphics interfaces, and CTMU hardware support that simplifies mTouch capacitive-button firmware. Boundary Scan (JTAG) is supported for production test access. USB and high-speed analog blocks from larger PIC32MX members are intentionally omitted in this 16-KB variant, making it the lowest-cost entry point in the family. Typical applications include low-cost capacitive touch user interfaces, consumer appliances with graphics LCDs via PMP, USB-less industrial sensors, and general-purpose embedded control. Compared with a discrete 8-bit MCU plus external ADC, the PIC32MX110F016B integrates peripherals and 32-bit compute into a single SOIC-28 footprint, reducing PCB area and BOM count. Designers should note that the 28-SOIC package is 0.300" wide (not the narrow 0.150" version); use appropriate land pattern. Decoupling: place a 100 nF ceramic near each VDD/VSS pair, with a 10 µF bulk capacitor at the regulator output. For CTMU touch sensing, follow Microchip AN1250 PCB layout guidelines to minimize trace-to-trace capacitance that can degrade touch sensitivity. This page synthesizes drop-in alternatives in the same 28-SOIC footprint, current distributor stock and pricing, and practical design considerations not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC32MX110F016B-I/SS - 40MHz 32-bit MCU 16KB Flash | Microchip
PIC32MX110F016B-I/SS

PIC32MX110F016B-I/SS - 40MHz 32-bit MCU 16KB Flash | Microchip

The Microchip PIC32MX110F016B-I/SS is a 32-bit MIPS32 M4K microcontroller delivering 40 MHz CPU performance with 16 KB Flash and 4 KB SRAM in a 28-pin SSOP package. It is part of the PIC32MX1XX/2XX family of general-purpose microcontrollers and is targeted at cost-sensitive embedded designs that need more performance than 8/16-bit MCUs can offer while retaining a simple peripheral set. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripherals such as timers, ADC, and communication interfaces on one die. The PIC32MX1XX/2XX family belongs to the broader category of 32-bit microcontrollers -> RISC microcontrollers -> MIPS32-based MCUs -> embedded processors -> semiconductors. It is designed as an entry-level upgrade path for engineers migrating from PIC16/PIC24 devices who need higher throughput for USB, graphics, or audio front-end tasks. Key features include a 10-bit ADC with up to 12 analog input channels, four hardware DMA channels, a Charge Time Measurement Unit (CTMU) for touch and capacitive sensing, two UART, two SPI, and two I2C peripherals, plus a Parallel Master Port (PMP) for graphics or external memory expansion. The 21 general-purpose I/O pins support Peripheral Pin Select (PPS), which allows digital peripheral signals to be remapped to a wide range of physical pins, simplifying PCB layout. The device operates from 2.3 V to 3.6 V with industrial -40C to +85C temperature range. Internally the PIC32MX110F016B uses the MIPS32 M4K core with single-cycle hardware multiply/divide, a 5-stage pipeline, and a separate PLL for the system clock. Five 16-bit timers/counters and a configurable watchdog with on-chip low-power RC oscillator provide robust task scheduling. The part supports ICSP (In-Circuit Serial Programming) and JTAG debugging through the MPLAB X IDE with the free XC32 compiler, enabling rapid firmware development. Typical applications include USB HID devices, low-cost audio playback front-ends, capacitive touch user interfaces, sensor hubs, and small graphic LCD controllers. The combination of CTMU, DMA, and PMP makes it a fit for human-machine interface (HMI) panels and consumer appliances. When designing with this MCU, allocate the 16 KB Flash budget carefully - the bootloader plus USB stack plus application code leaves only a few KB for user logic. Use the CTMU and DMA offload the CPU from touch scanning to keep MIPS available for application work. Pin 1 dot marker should be observed carefully for SSOP-28 land pattern. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers and buyers a single reference for evaluation.

RFQ যোগাযোগ
PIC32MX110F016B-V/SP - 40MHz 32-bit MCU, 16KB Flash | Microchip
PIC32MX110F016B-V/SP

PIC32MX110F016B-V/SP - 40MHz 32-bit MCU, 16KB Flash | Microchip

The Microchip Technology PIC32MX110F016B-V/SP is a 32-bit RISC microcontroller built on the MIPS32 M4K core, running up to 40 MHz with less than 0.5 mA/MHz current consumption, housed in a 28-pin SPDIP package. The device integrates 16 KB of Flash program memory and 4 KB of SRAM, 21 general-purpose I/O pins, and operates from a 2.3 V to 3.6 V supply across a -40 °C to +105 °C industrial temperature range. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich peripheral set on one die. Within the broader taxonomy, PIC32MX devices sit between 8-bit PIC16/PIC18 MCUs and higher-end Cortex-M parts, forming Microchip's mid-range 32-bit MCU family targeting audio/graphics, USB, and advanced analog applications. The PIC32MX110F016B-V/SP is positioned as the entry-level Flash member of the PIC32MX1XX/2XX 28/36/44-pin family, optimized for cost-sensitive designs that still need DSP-class throughput and USB connectivity. Key differentiating features include Peripheral Pin Select (PPS) for flexible function-to-pin remapping, a Parallel Master Port (PMP) for graphics interfaces, two I2S/SPI modules for codec/serial audio, a 10-bit ADC with multiple analog channels, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. Direct Memory Access (DMA) offloads CPU data movement, while five 16-bit timers (and up to two 32-bit timers) give flexible event timing. AEC-Q100 qualification supports automotive deployment, especially in the -V (industrial-grade) operating range. Architecturally, the MIPS32 M4K core executes most instructions in a single cycle with hardware multiply/divide and a 5-stage pipeline. The 16 KB Flash and 4 KB SRAM are sized for compact control loops, USB device stacks (CDC/HID/MSD), and small graphical user interfaces rendered via PMP to external LCD controllers. DMA channels move peripheral data to RAM without CPU intervention, leaving headroom for application code. Typical applications include low-cost USB peripherals, capacitive touch human-machine interfaces (HMIs), audio/graphic control panels using external PMP-attached LCDs, sensor conditioning nodes with on-chip ADC, and general-purpose industrial controllers. The automotive-grade (-V) variant also suits body-electronics and HMI modules where AEC-Q100 qualification is required. Design consideration: with less than 0.5 mA/MHz active current, regulator choice should focus on low-noise, low-IQ LDOs; bulk decoupling of 10 µF ceramic plus 0.1 µF HF bypass near each VDD pin is recommended per the family datasheet. PPS routing must be reconfigured after each reset, so save PPS maps in non-volatile configuration. This page synthesizes distributor pricing (as of 2026-10-01), drop-in same-package alternatives from Microchip's PIC32MX1XX/2XX family, and practical design notes not aggregated on a single manufacturer or distributor page.

RFQ যোগাযোগ
PIC32MX110F016B-V/SS - 40MHz 32-bit MCU, 16KB Flash, 28-SSOP | Microchip
PIC32MX110F016B-V/SS

PIC32MX110F016B-V/SS - 40MHz 32-bit MCU, 16KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC32MX110F016B-V/SS is a 32-bit MIPS M4K microcontroller operating at 40 MHz with 16 KB Flash and 4 KB SRAM, housed in a 28-pin SSOP (R-PDSO-G28) surface-mount package. The device runs from a 2.3V to 3.6V supply, delivers up to 21 general-purpose I/O pins, and integrates peripherals such as two I2S/SPI modules, a Parallel Master Port (PMP), Peripheral Pin Select (PPS), and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals such as timers, communication controllers, and analog blocks. The PIC32MX1XX/2XX family belongs to the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. Within Microchip's portfolio, the PIC32MX sits between the 16-bit PIC24F/G and the higher-end PIC32MZ families, balancing MIPS performance, low power, and rich peripheral integration for cost-sensitive designs. Key differentiating features include Peripheral Pin Select (PPS), which remaps most digital peripherals to any compatible I/O pin - dramatically simplifying PCB layout and reducing pin conflicts. The integrated CTMU enables capacitive touch measurement via a single ADC channel and timing source, supporting mTouch buttons, sliders, and proximity sensing without an external touch controller. The PMP interface supports graphics LCDs, and the dual I2S/SPI blocks support audio codecs and full-duplex serial communications. Architecturally, the PIC32MX110F016B-V/SS uses the MIPS32 M4K core with a 5-stage pipeline, hardware multiply/divide, and tightly-coupled SRAM for deterministic interrupt response. The Flash program memory supports self-programming via the boot Flash region, and the device includes an on-chip debugger accessible through the ICSP interface using MPLAB Snap, MPLAB ICD-4, or PICkit 4. Typical applications include consumer audio peripherals, low-cost HMI panels, capacitive-touch human-interface devices, USB HID peripherals, industrial sensor hubs, and low-power IoT edge nodes. The wide operating temperature range (-40C to +105C) and 2.3V-3.6V supply suit battery and industrial 3.3V bus systems. The PIC32MX110F016B-V/SS offers compelling price-to-performance compared with 8/16-bit MCUs for designs requiring MIPS-class throughput without the cost of higher-tier PIC32MZ parts. Design tip: place a 0.1 uF decoupling capacitor as close as possible to every VDD/VSS pair, and connect the MCLR pin through a 10 kohm pull-up to VDD for proper reset behavior. Use PPS to assign peripherals to convenient pins during schematic capture, and configure the CTMU via the dedicated CTMUCON register set for accurate touch measurements. This page synthesizes distributor pricing, drop-in alternatives within the PIC32MX1XX family, application companion ICs, and practical design notes beyond the manufacturer datasheet DS60001168L, supporting BOM optimization and second-source decisions.

RFQ যোগাযোগ
PIC32MX110F016BT-V/ML - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip
PIC32MX110F016BT-V/ML

PIC32MX110F016BT-V/ML - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip

The Microchip Technology PIC32MX110F016BT-V/ML is a 32-bit MIPS32 M4K RISC microcontroller running at 40 MHz, equipped with 16 KB of Flash program memory and 4 KB of SRAM, in a 28-pin QFN (6 x 6 mm) package with an exposed thermal pad. It operates from 2.3 V to 3.6 V and is qualified to AEC-Q100 for automotive applications, with a temperature range of -40 °C to +105 °C. The device integrates USB Full-Speed, two I²S/SPI modules, two UART/I²C modules, a Parallel Master Port (PMP) for graphics interfaces, and Peripheral Pin Select (PPS) for flexible routing of digital peripherals. A microcontroller (MCU) is an integrated circuit containing a CPU core, program and data memory, and programmable peripherals such as timers, communication interfaces, and analog blocks. PIC32MX110F016B sits inside the Microchip PIC32MX family, which in turn belongs to the broader 32-bit microcontroller category within the larger family of embedded processors that includes ARM Cortex-M, RISC-V, and MIPS architectures. MCUs are the central compute element of nearly every embedded system, executing firmware that interacts with sensors, actuators, displays, and external buses. Key features of this device include 21 general-purpose I/O pins, four DMA channels with automatic data size detection, a 10-bit ADC with multiple channels, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive-touch sensing. Two separate PLLs (one for the CPU, one for USB) simplify mixed-clock designs, and five 16-bit timers cover a wide range of PWM and capture/compare tasks. The configurable Watchdog Timer with on-chip Low-Power RC oscillator enhances safety in noisy or low-power modes. The architecture combines a MIPS32 M4K core with Microchip's Peripheral Pin Select (PPS) fabric, allowing remapping of most digital peripherals to virtually any I/O pin. This is especially valuable in compact 28-pin designs where pin assignments often conflict with PCB layout, eliminating the need to re-spin a board for routing reasons. The integrated Full-Speed USB 2.0 device controller with on-chip transceiver simplifies connectivity without an external PHY. Typical applications include automotive body and infotainment modules, USB Human Interface Devices (HIDs) such as keyboards and mice, graphics interfaces via PMP for low-cost LCDs, capacitive touch panels using mTouch, and industrial control nodes. The wide operating voltage range and AEC-Q100 qualification make it well-suited to automotive and harsh industrial environments. When designing with this device, allocate PCB copper under the exposed pad for thermal relief and ensure the decoupling network uses 100 nF plus bulk capacitance within a few millimetres of the supply pins. The PPS feature must be configured at startup; forgetting to enable a peripheral's PPS mapping is a common first-time designer pitfall. This page synthesizes official Microchip specifications, AEC-Q100 automotive qualification details, drop-in PIC32MX1x0 family alternatives, and practical design notes that are not assembled in a single place on the manufacturer datasheet or distributor listing.

RFQ যোগাযোগ
PIC32MX110F016BT-V/SO - 40MHz 32-bit MCU 16KB Flash | Microchip
PIC32MX110F016BT-V/SO

PIC32MX110F016BT-V/SO - 40MHz 32-bit MCU 16KB Flash | Microchip

The Microchip PIC32MX110F016BT-V/SO is a 32-bit MIPS32 M4K RISC microcontroller operating at 40 MHz, integrating 16 KB of Flash program memory and 4 KB of SRAM in a 28-pin SOIC package. It belongs to the PIC32MX1x0 family and is supplied from a 2.3 V to 3.6 V rail with 21 general-purpose I/O pins, supporting an operating temperature range of -40 °C to +105 °C for industrial and AEC-Q100 automotive grade deployments. A 32-bit microcontroller (MCU) is a programmable computing element that executes instructions from on-chip Flash memory, drives digital I/O, and interfaces with analog peripherals such as ADC, comparators and timers. PIC32MX1x0 devices sit at the low-memory end of the broader PIC32 family — they extend Microchip's PIC architecture into 32-bit territory while preserving the MPLAB X IDE and Harmony ecosystem. They are descendants of the original PIC microcontroller line, which established the 8-bit MCU category, and represent the migration path into higher-performance MIPS-based silicon for embedded designs. Key features include a single-core MIPS32 M4K CPU running up to 40 MHz with < 0.5 mA/MHz active current, on-chip 10-bit ADC, two I²S/SPI modules for audio codec connectivity, Peripheral Pin Select (PPS), a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) supporting mTouch™ capacitive touch buttons and sliders. Five 16-bit general-purpose timers and DMA channels enable offloading of repetitive data movement. Architecturally, the device uses Harvard-style separated instruction/data buses with a 5-stage pipeline, single-cycle multiply and hardware divider, and tightly-coupled peripheral buses. USB 2.0 full-speed, I²C, UART, SPI, and PMP peripherals share pins through the PPS multiplexer, simplifying PCB routing in compact 28-pin layouts. Typical applications include automotive body electronics, industrial control panels, consumer audio peripherals, USB HID devices, and low-cost graphical user interfaces driving small LCDs. The wide operating voltage range and -40 °C to +105 °C thermal envelope also suit outdoor IoT edge nodes. When designing with this MCU, ensure decoupling uses 100 nF + 10 µF placed within 5 mm of the VDD pins; PPS reassignments must be configured at runtime and unlocked via IOLOCK before peripheral changes. The 'T' suffix denotes tape-and-reel packaging; the 'V' temperature code designates the -40 °C to +105 °C automotive-grade window. This page synthesizes distributor pricing, drop-in alternatives in the same 28-SOIC footprint, and practical design notes not consolidated on the manufacturer product page, providing procurement-grade context for engineers evaluating PIC32MX1x0 devices.

RFQ যোগাযোগ
PIC32MX110F016BT-V/SS - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip
PIC32MX110F016BT-V/SS

PIC32MX110F016BT-V/SS - 32-bit 40MHz MCU, 16KB Flash, AEC-Q100 | Microchip

The Microchip Technology PIC32MX110F016BT-V/SS is a 32-bit MIPS M4K microcontroller running at 40 MHz, integrating 16 KB of Flash and 4 KB of SRAM in a 28-pin SSOP package. It supports an operating voltage range of 2.3V to 3.6V and is AEC-Q100 qualified for automotive applications. What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/SRAM), and a rich set of peripherals (UART, I2C, SPI, timers, ADC, PWM, etc.) into one package. 32-bit MCUs execute instructions over a wider data path than 8-bit or 16-bit MCUs, enabling higher computational throughput, larger addressable memory, and more efficient handling of complex algorithms. Within the Microchip taxonomy, the PIC32MX family sits at the low-power / cost-optimized end of the 32-bit PIC32 portfolio, bridging the gap between 16-bit PIC24/dsPIC devices and high-performance PIC32MZ parts. Key features include two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, a Parallel Master Port (PMP) for graphics interfaces, and a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing. The 40 MHz CPU with MIPS32 M4K core delivers less than 0.5 mA/MHz active current, and the part includes up to four DMA channels, two UART, and two I2C modules. The AEC-Q100 "V" suffix designates the automotive grade, making this part suitable for in-vehicle designs. The PIC32MX110 architecture uses a 5-stage pipeline MIPS32 M4K core with single-cycle hardware multiply and divide, paired with separate PLLs for CPU and USB clocks. PPS allows digital peripheral I/O to be remapped to most general-purpose I/O pins, simplifying PCB layout. Multiple power-management modes (Run, Idle, Sleep) plus a configurable WDT with on-chip low-power RC oscillator support long battery-life or energy-harvesting applications. Typical applications include automotive body electronics and HMI nodes, capacitive touch buttons and sliders via mTouch, USB audio peripherals, low-cost graphics interfaces through PMP, and general-purpose 32-bit embedded control. The wide peripheral mix and automotive qualification also make it suitable for industrial sensor hubs and consumer appliances requiring a 32-bit upgrade path from 16-bit PIC24 designs. When designing with this MCU, reserve a clean 3.3V analog rail for the AVDD pin pair and place the decoupling capacitors within 3 mm of the supply pins. The PPS registers must be unlocked and configured before any remapped peripheral works correctly - failing to do this is one of the most common bring-up pitfalls for first-time PIC32 users. This page consolidates distributor pricing, automotive-grade drop-in alternatives, and practical design guidance that the bare Microchip datasheet does not present together.

RFQ যোগাযোগ
PIC32MX110F016C-I/TL - 32-bit 40MHz 16KB Flash MCU | Microchip
PIC32MX110F016C-I/TL

PIC32MX110F016C-I/TL - 32-bit 40MHz 16KB Flash MCU | Microchip

The Microchip PIC32MX110F016C-I/TL is a 32-bit MIPS32 M4K microcontroller running at 40 MHz with 16 KB Flash and 4 KB SRAM, housed in a 36-pin VTLA (5x5 mm) package with an exposed thermal pad. It operates from 2.5 V to 3.6 V and is qualified to the industrial -40C to +85C temperature range. The part integrates rich connectivity (I2C, IrDA, LIN, PMP, SPI, UART/USART) and Microchip's Peripheral Pin Select (PPS) for flexible signal routing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of peripherals. The PIC32MX110 family belongs to the broader 32-bit MCU category, which sits above 8-bit and 16-bit MCUs in performance and addresses the same role as ARM Cortex-M0/M3 parts. Within Microchip's portfolio, the 32-bit MIPS-based PIC32 line competes with the dsPIC and PIC24 16-bit lines as well as Microchip's own ARM-based SAM family. Key features include 16 KB (16K x 8) Flash, 4 KB SRAM, hardware DMA (up to 4 channels), configurable Watchdog Timer with on-chip Low-Power RC oscillator, multiple power-management (Sleep/Idle) modes, and JTAG/ICSP debug. PPS remaps digital peripherals to almost any I/O pin, easing PCB layout for dense designs. The device is built around a MIPS32 M4K Harvard core with single-cycle hardware multiply and a 5-stage pipeline. The 40 MHz core delivers approximately 50 DMIPS, and the bus matrix connects the core, DMA engine, and peripherals without stalling the CPU. The 36-VTLA package uses an exposed pad for thermal relief. Typical applications include consumer and industrial embedded control, USB-less PIC32 designs, sensor hubs, low-cost graphical user interfaces (with PMP to TFT/segment LCD), and educational or hobby platforms. The 16 KB Flash / 4 KB SRAM balance fits small TCP/IP or USB stacks running on a sister PIC32 part. When designing, allocate Flash budget carefully - 16 KB accommodates roughly 12 KB of code after the bootloader, leaving limited room for field-upgrade images. Plan ICSP pins early: any PGECx/PGEDx pair is valid for debug and programming, but only as a matched pair. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC32MX110F016C-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
PIC32MX110F016C-V/TL

PIC32MX110F016C-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip

The Microchip Technology PIC32MX110F016C-V/TL is a 32-bit MIPS M4K microcontroller from the PIC32MX1xx/2xx family, integrating 16 KB of Flash program memory and 4 KB of SRAM in a 36-pin VTLA (5x5 mm) package with exposed thermal pad. It operates at up to 40 MHz with sub-0.5 mA/MHz active current, and is rated for the automotive -40C to +105C temperature range (V-temp grade). The device targets audio, graphics, USB-capable, and general-purpose embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of peripheral interfaces into one package. The PIC32MX110F016C belongs to the broader category of 32-bit microcontrollers, which sit architecturally above 8-bit and 16-bit MCUs and below microprocessor units (MPUs) that require external memory. Within Microchip's portfolio it occupies the low-pin-count, low-memory tier of the PIC32MX family, suitable for cost-sensitive applications that still demand 32-bit performance, DSP capability, and modern peripherals. Key features include two I2S/SPI modules for audio codec interfacing, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics or memory-mapped peripherals, and a Charge Time Measurement Unit (CTMU) that supports mTouch capacitive touch sensing. Integrated connectivity includes I2C, IrDA, LINbus, SPI, UART/USART, and PMP. On-chip system resources comprise Brown-out Detect/Reset, DMA, POR, PWM, and a Watchdog Timer, enabling robust single-chip designs in industrial and automotive environments. The M4K core delivers 1.56 DMIPS/MHz and supports the MIPS32 instruction set including DSP ASE extensions, allowing efficient audio decoding and signal-processing workloads at modest clock rates. The 2.3V-3.6V single-supply range simplifies integration with 3.3V analog and digital peripherals, while the VTLA-EP package exposes a thermal pad for improved heat spreading during continuous full-load operation. Typical applications include automotive body and comfort modules, consumer audio accessories with I2S codecs, low-cost HMI panels using PMP-driven LCDs, capacitive-touch user interfaces leveraging CTMU, and LIN-bus slave nodes. The AEC-Q100 qualification makes it a direct fit for in-cabin automotive electronics. When designing with this device, observe the 3.3V supply limit, use PPS to remap peripherals to convenient package pins, and follow Microchip's PIC32MX1xx/2xx family reference manual for oscillator and PLL configuration. Decouple VDD/AVDD with 100 nF plus bulk capacitance placed within 5 mm of each pin pair. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC32MX1xx/2xx family, and practical design notes that complement the Microchip datasheet with sourcing and selection guidance.

RFQ যোগাযোগ
PIC32MX110F016CT-I/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
PIC32MX110F016CT-I/TL

PIC32MX110F016CT-I/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip

The Microchip Technology PIC32MX110F016CT-I/TL is a 32-bit MIPS M4K microcontroller with 16KB of Flash program memory and 4KB of SRAM, operating at up to 40MHz. It is housed in a 36-pin VTLA (5x5 mm) package with an exposed thermal pad, optimized for compact surface-mount designs that demand high MIPS-per-dollar performance in a small footprint. What is a 32-bit microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash and RAM), and peripherals (UART, I2C, SPI, ADC, timers) into one package. The PIC32MX family sits in the hierarchy: microcontroller -> 32-bit MCU -> MIPS-based MCU -> PIC32MX family -> PIC32MX1xx sub-family. It targets cost-sensitive applications where 8-bit MCUs run out of headroom but full application processors are overkill, bridging the gap between Microchip's PIC16/PIC24 lines and higher-end PIC32MZ devices. Key features include 16KB of Flash with self-programming support, 4KB of SRAM, a 10-bit 1 Msps ADC with up to 13 channels, two UART, two I2C, and two SPI modules, plus five 16-bit timers/counters. The peripheral pin select (PPS) feature allows flexible remapping of digital peripherals to any I/O pin, simplifying PCB routing. The device operates from 2.3V to 3.6V and supports industrial temperature ranges of -40C to +85C. Architecturally, the MIPS32 M4K core delivers 1.56 DMIPS/MHz with single-cycle multiply and hardware divide, supported by a 5-stage pipeline. The integrated DMA controller with up to four channels offloads data movement between peripherals and memory, freeing the CPU for application code. Separate PLLs handle CPU and USB clocking, enabling flexible system timing. Typical applications include low-cost IoT sensor nodes, USB device peripherals, consumer appliances, industrial control interfaces, and human-machine interface (HMI) touch panels. The combination of small package, USB 2.0 full-speed support, and rich peripherals makes the PIC32MX110F016C family a versatile entry point for embedded designs. When designing with this MCU, ensure the exposed thermal pad is properly soldered to a sufficient copper pour to meet thermal specifications. Use MPLAB X IDE with XC32 compiler for development, and consider the PIC32MX1xx/2xx family datasheet and the family reference manual for peripheral programming details. This page consolidates distributor pricing, drop-in alternative options within the PIC32MX family, and practical design notes that supplement the manufacturer datasheet.

RFQ যোগাযোগ
PIC32MX110F016CT-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip
PIC32MX110F016CT-V/TL

PIC32MX110F016CT-V/TL - 32-bit MCU, 16KB Flash, 40MHz | Microchip

The Microchip PIC32MX110F016CT-V/TL is a 32-bit RISC microcontroller built on the MIPS32 M4K core, delivering up to 40 MHz clock speed, 16 KB of Flash program memory and 4 KB of SRAM, housed in a 36-pin VTLA (5x5 mm, 0.5 mm pitch) surface-mount package. The device offers 25 general-purpose I/O lines and an AEC-Q100 qualification for automotive applications, with connectivity including I2C, SPI, UART/USART, IrDA, LINbus and PMP. A 32-bit microcontroller (MCU) is an integrated circuit that combines a high-performance CPU, program memory (typically Flash), data memory (SRAM), and programmable peripherals on a single die. The PIC32MX1x0 family sits in Microchip's PIC32 portfolio above 8-bit PIC16/PIC18 and 16-bit PIC24 dsPIC parts but below the high-pin-count PIC32MZ series. It targets cost-sensitive, mixed-signal embedded designs that require deterministic real-time behaviour, low power consumption, and rich connectivity. Within the broader semiconductor taxonomy, the PIC32MX110F016CT-V/TL is a microcontroller (MCU), a member of the system-on-chip (SoC) category, used in power management, sensing, and control subsystems. Key features include a 5-channel 10-bit ADC for analog sensing, 4 hardware DMA channels, Peripheral Pin Select (PPS) for flexible pin mapping, a 16-bit timer/counter, and configurable WDT with on-chip low-power RC oscillator. The device supports 1.6 MIPS per MHz performance and operates across a 2.3 V to 3.6 V supply, suitable for battery-powered and industrial-grade systems. Architecture-wise, the MIPS32 M4K core implements a 5-stage pipeline and executes most instructions in a single cycle. A separate PLL provides flexible clock generation from the internal 8 MHz RC oscillator or external crystal, and dedicated DMA engines offload peripheral data movement from the CPU, improving determinism. Typical applications include automotive body electronics (LIN-bus nodes, HVAC controls, sensor clusters), industrial sensor hubs, IoT edge nodes, low-cost HMI touch pads, and consumer white-goods controllers where AEC-Q100 qualification and LINbus compliance are required. When designing with this part, place a 0.1 µF decoupling capacitor close to each VDD/VSS pair and follow the recommended 4-layer PCB stack-up to keep EMI below AEC-Q100 limits. This page synthesises distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
PIC32MX110F016D-I/ML - 32-bit MCU 40MHz 16KB Flash 44-QFN | Microchip
PIC32MX110F016D-I/ML

PIC32MX110F016D-I/ML - 32-bit MCU 40MHz 16KB Flash 44-QFN | Microchip

The Microchip Technology PIC32MX110F016D-I/ML is a 32-bit RISC microcontroller built on the MIPS32 M4K core, running at 40 MHz with 16 KB of Flash program memory and 4 KB of SRAM, housed in a 44-pin QFN (8x8 mm) package with an exposed thermal pad. It operates from a 2.3V to 3.6V supply and supports an industrial temperature range of -40 °C to +105 °C. A 32-bit microcontroller (MCU) is an integrated processor core, program memory, data memory, and a rich set of peripherals on a single silicon die. PIC32MX devices sit in Microchip's PIC32 family under the MIPS32 M4K architecture, a branch of the broader microcontroller category within the power management and embedded computing domain. They balance deterministic real-time performance with high code density. Key features include two I2S/SPI modules for codec and serial communications, Peripheral Pin Select (PPS) for flexible pin mapping, a Parallel Master Port (PMP) for graphics interfaces, a Charge Time Measurement Unit (CTMU) that enables mTouch capacitive-touch buttons and sliders, four DMA channels, and a 10-bit ADC. The CTMU, PPS, and PMP combination differentiates this MCU from simpler ARM Cortex-M0+ parts that require external glue logic for capacitive touch and graphics. At 40 MHz the core draws less than 0.5 mA/MHz active current, while the on-chip 1.5 Msps 10-bit ADC, five 16-bit general-purpose timers, and a real-time clock and calendar (RTCC) provide sufficient analog and timing depth for sensor-hub, HMI, and low-cost graphics products. JTAG and two-wire programming/debug interfaces are included for development. Typical applications include consumer and industrial human-machine interfaces (HMIs), low-cost graphical LCD or segment displays driven through PMP, capacitive-touch control panels using CTMU-based mTouch firmware, USB device or audio bridges leveraging the integrated I2S modules, and sensor hubs combining ADC, RTCC, and DMA for low duty-cycle battery-powered products. When designing with this device, allocate pins for the I2S, PMP, and JTAG interfaces early, since PPS remapping cannot replace lost physical pins; use the exposed pad of the QFN package as the primary ground and thermal path. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC32MX1xx family, and practical design notes that go beyond what the manufacturer datasheet lists in isolation.

RFQ যোগাযোগ
PIC32MX110F016D-I/PT - 32-bit MCU, 16KB Flash, 40MHz, TQFP-44 | Microchip
PIC32MX110F016D-I/PT

PIC32MX110F016D-I/PT - 32-bit MCU, 16KB Flash, 40MHz, TQFP-44 | Microchip

The Microchip PIC32MX110F016D-I/PT is a 32-bit MIPS32 M4K RISC microcontroller operating up to 40 MHz, with 16 KB Flash and 4 KB SRAM, housed in a 44-pin TQFP (10x10 mm) package. It integrates up to 21 general-purpose I/O, 4 DMA channels, two I2S/SPI modules, and an on-chip 10-bit ADC, all operating from a 2.3 V to 3.6 V rail. Typical dynamic current is below 0.5 mA/MHz, making it a strong fit for low-power embedded designs. What is a PIC32MX microcontroller? The PIC32MX family is Microchip's line of 32-bit MIPS-based microcontrollers, sitting in the taxonomy: microcontroller -> embedded MCU -> 32-bit MCU -> MIPS M4K core. PIC32MX parts combine the legacy PIC peripheral set with the wider 32-bit MIPS datapath, providing integer performance up to ~52 DMIPS at 40 MHz while keeping code-density benefits of the MIPS instruction set. Key features include Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics or external memory interfaces, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch buttons and sliders, brown-out reset, power-on reset, and five 16-bit timers. The integrated 10-bit ADC, multiple UART/I2C/SPI peripherals, and USB-ready companion peripherals allow this device to replace external logic in cost-sensitive nodes. From an architectural standpoint, the PIC32MX110F016D uses a Harvard-style MIPS32 M4K core with separate Flash and SRAM buses, supporting 16 KB Flash for code and 4 KB SRAM for data. Its DMA controller offloads I/O from the CPU, and the CTMU provides a precise time-measurement current source for touch sensing without external analog components. Typical applications include low-cost USB device nodes, capacitive touch user interfaces, small graphics LCDs driven by PMP, industrial sensor conditioning nodes, and consumer appliances needing 32-bit headroom at 8-bit prices. The industrial temperature grade (-40 C to +85 C) suits outdoor enclosures and factory-floor deployments. When designing with this part, ensure the 2.3 V to 3.6 V supply is decoupled with 100 nF plus 10 uF bulk capacitors close to the VDD pins, and use PPS to remap peripherals when the PCB layout forces non-standard pin assignments. For migration, the same die is offered in 44-QFN (PIC32MX110F016D-V/ML) for space-constrained boards. This page synthesizes distributor pricing, verified drop-in alternatives within the same Microchip 44-pin TQFP family, and practical design notes that are not consolidated in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC32MX110F016D-V/ML - 40MHz 32-bit MCU, 16KB Flash | Microchip
PIC32MX110F016D-V/ML

PIC32MX110F016D-V/ML - 40MHz 32-bit MCU, 16KB Flash | Microchip

The Microchip PIC32MX110F016D-V/ML is a 32-bit MIPS32 M4K RISC microcontroller running at 40 MHz with 16 KB of on-chip Flash and 4 KB of SRAM, packaged in a 44-pin QFN (ML) 8x8 mm with an exposed thermal pad for improved thermal dissipation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (SRAM), and a rich set of peripherals onto one silicon die. Within the broader taxonomy, the PIC32MX110F016D belongs to the PIC32MX1xx family of general-purpose 32-bit microcontrollers, which sits under Microchip's PIC32 family and ultimately under the MIPS-based MCU product line for embedded control. The 'D' suffix denotes an integrated Parallel Master Port (PMP) for graphics and external memory interfacing, while the 'V' temperature grade extends the operating range to -40C to +105C for industrial environments. Key features include up to 21 general-purpose I/O pins with Peripheral Pin Select (PPS) remapping, two I2S/SPI modules for codec and audio interfacing, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing, an RTCC, 3 analog comparators, and 4-channel DMA. The device consumes less than 0.5 mA/MHz active current and operates from 2.3 V to 3.6 V. Additional peripherals include five 16-bit timers, two UART modules, two I2C modules, and a 10-bit 1 Msps ADC. Architecturally, the PIC32MX110F016D uses a Harvard-style MIPS32 M4K core with a 5-stage pipeline, single-cycle hardware multiply/divide, and a prefetch cache to maximize throughput from Flash. The result is deterministic interrupt response suitable for hard real-time control, while the integrated DMA engine offloads repetitive peripheral data movement from the CPU. Typical applications include industrial control panels with capacitive touch, low-cost audio playback with I2S DACs, USB device nodes (via on-chip USB FS), graphical user interfaces using PMP, smart sensors, and home appliances. The integrated CTMU makes the part particularly attractive for cost-sensitive human-machine interfaces. When designing with this device, ensure the exposed pad (EP) is soldered to a sufficient ground copper pour to meet thermal and electrical performance; verify PPS remapping against the device variant's pin map; and use MPLAB XC32 with the appropriate compiler license to unlock optimizations above -O1. This page synthesizes current distributor pricing, verified drop-in alternatives from the same PIC32 family, and practical design notes that go beyond what the manufacturer datasheet alone offers.

RFQ যোগাযোগ
PIC32MX110F016DT-I/ML - 32-bit 40MHz MCU 16KB Flash | Microchip
PIC32MX110F016DT-I/ML

PIC32MX110F016DT-I/ML - 32-bit 40MHz MCU 16KB Flash | Microchip

The Microchip Technology PIC32MX110F016DT-I/ML is a 32-bit RISC microcontroller from the PIC32MX1XX/2XX family, featuring a MIPS32 M4K core running up to 40 MHz with 16 KB of Flash and 4 KB of SRAM in a 44-pin QFN (8x8 mm) package with exposed thermal pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals on one die. The PIC32MX110F016D specifically combines a 32-bit MIPS core (M4K) with the cost-effective peripheral set typical of Microchip's PIC32 entry-level portfolio. Within the broader taxonomy, this part sits in the hierarchy: PIC32MX1XX -> PIC32MX family -> PIC32 -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. The M4K core executes most instructions in a single cycle and supports the standard MIPS32 instruction set, giving it noticeably higher throughput than 8-bit or 16-bit alternatives at similar clock rates. Key features include an operating voltage range of 2.3V to 3.6V (3.3V typical), industrial-grade -40C to +105C temperature range, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics interfaces, two I2S/SPI modules for audio codec connectivity, a Charge Time Measurement Unit (CTMU) for mTouch capacitive touch sensing, and up to 32 KB of Flash in the family. The device also integrates separate PLLs for CPU and USB clocks, two UART and I2C modules, and multiple low-power modes with less than 0.5 mA/MHz active current consumption. The architecture uses a 5-stage pipeline with hardware multiply/divide and a deterministic interrupt controller, making the M4K core well suited to real-time control. On-chip DMA (up to 4 channels with automatic data size detection) offloads data movement from the CPU, freeing bandwidth for application code. USB 2.0 full-speed device capability is supported through the dedicated USB PLL, removing the need for an external clock source in many designs. Typical applications include consumer electronics with USB connectivity, audio playback and processing (using I2S), low-cost graphics user interfaces via PMP, capacitive touch button or slider panels using CTMU, and general-purpose 32-bit embedded control upgrades for legacy PIC24 or PIC16 designs. The PIC32MX110F016DT-I/ML ships in tape and reel packaging for high-volume assembly. Designers should verify pin assignment against the specific 44-QFN variant - the 'ML' suffix denotes the 8x8 mm QFN package, whereas the 'PT' suffix denotes TQFP-44. The 'T' character in the MPN indicates tape-and-reel delivery, and the 'I' indicates the -40C to +105C industrial temperature grade. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not all available in the manufacturer datasheet alone.

RFQ যোগাযোগ
PIC32MX110F016DT-I/TL - 32-bit MCU 16KB Flash 40MHz 44-VFTLA | Microchip
PIC32MX110F016DT-I/TL

PIC32MX110F016DT-I/TL - 32-bit MCU 16KB Flash 40MHz 44-VFTLA | Microchip

The Microchip Technology PIC32MX110F016DT-I/TL is a 32-bit RISC microcontroller built on the MIPS32 M4K core, delivering up to 40 MHz CPU clock performance with less than 0.5 mA/MHz active current consumption. It integrates 16 KB of Flash program memory and 4 KB of SRAM in a 44-pin VFTLA (VTLA) exposed-pad surface-mount package, combining 32-bit processing throughput with a rich peripheral set for cost-sensitive embedded applications. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and programmable peripherals on one die. Within the broader semiconductor taxonomy, the PIC32MX family sits between 8/16-bit legacy MCUs and high-end Cortex-M cores, targeting the "32-bit performance at near 16-bit cost" design point. The M4K core adds DSP-like arithmetic and Single-Cycle Multiplication to help audio and graphics signal processing without a dedicated DSP. Key differentiating features of this part include two I2S/SPI modules for codec interfacing, Peripheral Pin Select (PPS) for flexible signal routing, a Parallel Master Port (PMP) for graphics displays, and a Charge Time Measurement Unit (CTMU) that enables Microchip's mTouch capacitive touch buttons and sliders. Five 16-bit general-purpose timers, up to four DMA channels with automatic data size detection, separate PLLs for CPU and USB clocks, and 21 general-purpose I/O pins complete the peripheral set. The PIC32MX110F016DT-I/TL is specified for an industrial temperature range of -40C to +105C and operates from 2.3 V to 3.6 V. The 'T' code in the part number indicates tape-and-reel packaging, 'I' indicates industrial temperature grade, and 'TL' designates the 44-pin VFTLA package. The compact 6 mm x 6 mm 0.65 mm-pitch package with exposed thermal pad helps thermal dissipation and PCB density. Typical applications include consumer audio accessories using I2S codecs, low-cost graphical user interfaces with PMP-driven LCDs, capacitive-touch user input panels leveraging CTMU, USB device peripherals using the on-chip USB peripheral and dedicated PLL, and general-purpose industrial control nodes that need 32-bit math at low BOM cost. When designing with this part, remember that PPS remaps must be unlocked before use, and the 2.3 V minimum supply rules out 1.8 V-only rails. The exposed thermal pad should be soldered to a continuous ground copper pour for electrical and thermal performance. This page synthesizes distributor pricing, drop-in VFTLA alternatives, and practical design notes not found in a single manufacturer datasheet. Refer to Microchip's PIC32MX1XX/2XX datasheet family for peripheral electrical specifications.

RFQ যোগাযোগ