মাইক্রোকন্ট্রোলার

পণ্য (20,000+)

TMS320F28379SPTPS - 200MHz C28x Delfino MCU 1MB Flash | TI
TMS320F28379SPTPS

TMS320F28379SPTPS - 200MHz C28x Delfino MCU 1MB Flash | TI

The Texas Instruments TMS320F28379SPTPS is a 32-bit C2000™ C28x Delfino™ functional-safety microcontroller integrating one C28x CPU plus one Control Law Accelerator (CLA), a floating-point unit (FPU) and a Trigonometric Math Unit (TMU). The device operates up to 200 MHz, delivers up to 400 MIPS of computational throughput and includes 1 MB (512K x 16) of on-chip flash with ECC. It is housed in a 176-pin HLQFP (24x24 mm) package with an exposed thermal pad. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program and data memory, peripherals and I/O into one package. The C2000 Delfino family specifically targets real-time control: motor drives, digital power converters, solar inverters and industrial servo loops. The 2837xS generation adds a CLA - an independent 32-bit floating-point coprocessor that offloads time-critical control loops from the main CPU, allowing closed-loop PWM, ADC sampling and feedback math to execute deterministically without CPU intervention. Key specifications include a 16-bit ADC subsystem with up to 3.5 MSPS aggregate throughput, three 12-bit DAC outputs, enhanced pulse-width modulator (ePWM) channels with high-resolution capability, configurable logic blocks (CLB), an external memory interface (EMIF), USB 2.0 (full-speed OTG), CAN, SPI, I2C, UART, McBSP and a 16-channel sigma-delta filter module. Functional-safety features include lockstep CPU options, ECC on flash/SRAM and a safety documentation package aligned with IEC 61508 SIL 3 and ISO 26262 ASIL-D system-level goals. The architecture combines a Harvard-bus C28x core with the parallel CLA, both supporting IEEE-754 single-precision float. Tightly-coupled memory (TCM) and a multi-layer bus matrix give deterministic interrupt latency critical for field-oriented control (FOC) loops and digital power compensation. The configurable logic block (CLB) augments this with user-programmable glue logic that previously required external CPLDs. Typical applications include industrial servo drives, AC induction and PMSM motor controllers, solar PV inverters, telecom rectifier modules, HEV/EV traction inverters, on-board chargers, digital power factor correction and welding power supplies. The 176-HLQFP footprint is also a common choice for power-conversion DSPs in 1U/2U telecom bricks. When designing with this part, plan decoupling for the 1.2 V core rail: at least 10 µF bulk plus 0.1 µF per VDD pair, placed within 5 mm of the balls. Route the analog and digital ground domains separately and join them at a single point under the exposed pad. The HLQFP exposed pad must be soldered to a continuous copper plane of at least 1 square inch to keep junction temperature below 105 °C at full 200 MHz CPU + 200 MHz CLA load.

RFQ যোগাযোগ
TMS320F28P550SG-Q1 - C2000 MCU 150MHz, 512KB Flash | TI
TMS320F28P550SG-Q1

TMS320F28P550SG-Q1 - C2000 MCU 150MHz, 512KB Flash | TI

The TMS320F28P550SG-Q1 is a C2000 real-time microcontroller from Texas Instruments, designed for power electronics applications. It features a 32-bit C28x CPU running at 150 MHz, 512 KB of flash memory, and a Control Law Accelerator (CLA) for real-time control. The device integrates five ADCs, a Configurable Logic Block (CLB), AES encryption, and a Neural Processing Unit (NPU), supporting high-power-density designs with GaN and SiC technologies. A C2000 MCU is a high-performance microcontroller optimized for real-time control in power conversion and motor control. As a member of the C2000 family, it sits in the hierarchy of embedded processors, bridging the gap between traditional MCUs and digital signal processors. The F28P55x series is specifically designed for ultra-low latency control loops. Key features include 150 MHz CPU speed, 512 KB flash, 256 KB RAM, and a 120 MHz CLA. The device has five 12-bit ADCs with up to 4 MSPS, and an enhanced PWM module for GaN/SiC switching. The NPU accelerates AI-based algorithms for industrial applications. The architecture combines the C28x DSP core with a CLA coprocessor, enabling concurrent control and computation. The device supports functional safety features and is AEC-Q100 qualified for automotive use. It operates from a 3.3V supply. Typical applications include automotive traction inverters, on-board chargers, solar inverters, and industrial motor drives. The high-resolution PWM and ADC capabilities make it suitable for high-frequency power conversion. For design, ensure robust decoupling on the VDD and VDDIO pins with 0.1uF and 10uF capacitors close to the package. Use the onboard temperature sensor for thermal monitoring.

RFQ যোগাযোগ
TMS320F28P559SJ-Q1 - 150MHz C2000 MCU 1.1MB Flash | Texas Instruments
TMS320F28P559SJ-Q1

TMS320F28P559SJ-Q1 - 150MHz C2000 MCU 1.1MB Flash | Texas Instruments

The Texas Instruments TMS320F28P559SJ-Q1 is an automotive-qualified C2000 real-time 32-bit microcontroller running at 150 MHz, integrating a C28x CPU with a Control Law Accelerator (CLA), 1.1MB flash memory, five ADCs, Configurable Logic Blocks (CLB), AES hardware security, and an on-chip Neural Processing Unit (NPU). It is available in a 100-pin LQFP (14x14 mm) package such as the F28P559SJ9PZQ1. A real-time MCU is a microcontroller optimized for deterministic, low-latency execution of closed-loop control algorithms. Within the embedded processor hierarchy, the C2000 family sits at the top of the TI real-time control portfolio, bridging general-purpose MCUs and DSPs, and is the de facto industry standard for digital power and motor control. Key features include the 150 MHz C28x fixed-point core for single-cycle 32-bit multiply operations, the parallel CLA floating-point co-processor that offloads control loops to cut ISR latency, and five high-precision ADCs enabling simultaneous multi-phase current sampling. The NPU accelerates edge-AI tasks such as motor condition monitoring, while AES encryption supports secure firmware updates for automotive systems. The F28P55x architecture targets high power density and high switching-frequency power electronics, including GaN and SiC based converters. Integrated CLB blocks replace external CPLD logic for PWM augmentation, and the rich ePWM, eQEP, and communication peripheral set (CAN, SPI, SCI, I2C) supports complete digital control systems on one chip. According to TI datasheet SPRSP85D (April 2024, revised April 2026), the F28P55x series also adds Programmable Gain Amplifiers (PGA) and USB support relative to the F28003x series. Typical applications include automotive onboard chargers and traction inverters, solar string inverters, servo and BLDC motor drives, and DC-DC fast charging modules. The AEC-Q100 automotive qualification makes it suitable for automotive OEM and Tier-1 designs requiring functional-safety workflows. When designing with this device, allocate flash headroom for OTA software updates and use the TI C2000Ware SDK reference designs, which include digital power and InstaSPIN motor control libraries validated on this family. This page synthesizes distributor availability data, drop-in alternatives within the same 100-LQFP footprint, and practical design notes not found in the manufacturer datasheet, so engineers can evaluate the TMS320F28P559SJ-Q1 for digital power, motor control, and automotive edge-AI designs in one place.

RFQ যোগাযোগ
TMS320F28P650SH-Q1 - 400 MIPS C2000 MCU with FPU64 | Texas Instruments
TMS320F28P650SH-Q1

TMS320F28P650SH-Q1 - 400 MIPS C2000 MCU with FPU64 | Texas Instruments

The Texas Instruments TMS320F28P650SH-Q1 is a real-time microcontroller from the C2000 family, designed for high-performance control applications. It features a single C28x CPU core combined with a Control Law Accelerator (CLA), delivering 400 MIPS at 200 MHz, and includes a floating-point unit (FPU64) for complex math. The device provides 768 KB of on-chip flash memory and a 16-bit analog-to-digital converter (ADC), making it well-suited for closed-loop control systems. The automotive-qualified (AEC-Q100) version in a 256-NFBGA (13x13) package ensures reliable operation in harsh environments. A C2000 real-time microcontroller is a specialized MCU optimized for control-loop processing in power electronics and motor drives. Unlike general-purpose MCUs, C2000 devices integrate high-speed ADCs, PWM generation units, and a hardware accelerator (CLA) to offload the CPU for faster response times. This makes them essential in applications like frequency inverters, electric vehicle traction, and grid power conversion. Key features include 400 MIPS performance with a dual-core architecture (C28x + CLA), FPU64 for single-cycle double-precision math, and 768 KB flash for extensive code storage. The 16-bit ADC provides high-resolution sensing, while the functional safety (FuSa) capability improves system reliability. The Q1 suffix indicates AEC-Q100 qualification, suitable for automotive applications. In terms of technical depth, the C28x CPU is a 32-bit fixed-point core with a Harvard architecture, while the CLA is a coprocessor that executes control algorithms in parallel with the CPU. The FPU64 enables double-precision floating-point operations, crucial for stabilization algorithms. The 256-NFBGA package offers a compact footprint with 256 balls, facilitating high-density PCB designs. Typical applications include industrial motor drives, solar inverters, electric vehicle powertrain, and grid-tied power converters. The 400 MIPS performance and high-resolution ADC make it ideal for high-frequency switching converters and servo control loops. When designing with this MCU, ensure adequate decoupling on the VDD and VDDA pins, and follow the recommended layout for the analog-to-digital converter reference. The CLA shares memory with the C28x, so proper synchronization is required to avoid data race conditions. For automotive revisions, maintain compliance with AEC-Q100 guidelines by closely following TI's reference designs.

RFQ যোগাযোগ
TMS320LF2406APZA - 16-Bit DSP 40MHz 64KB Flash MCU | TI
TMS320LF2406APZA

TMS320LF2406APZA - 16-Bit DSP 40MHz 64KB Flash MCU | TI

The Texas Instruments TMS320LF2406APZA is a 16-bit fixed-point digital signal controller from the C2000 C24x family, delivering 40 MIPS at a 40-MHz clock with a 25-ns instruction cycle, integrating 64KB (32K x 16) of on-chip flash memory in a 100-pin LQFP (14x14 mm) surface-mount package operating from a low-power 3.3-V supply. A digital signal processor (DSP) is a specialized microprocessor architected for high-speed real-time numeric computation. The C2000 family sits in the hierarchy of microcontrollers optimized for closed-loop embedded control, combining a DSP CPU core with microcontroller peripherals such as PWM timers, serial ports, and CAN. This hybrid design enables engineers to implement PID loops, field-oriented control (FOC), and power-conversion algorithms on a single chip. Key features include the TMS320C2xx CPU core with a 16x16-bit hardware multiplier, 32-bit accumulator, and barrel shifter; two event manager modules optimized for PWM generation with dead-band control for motor drives; and a CAN 2.0B communications module. The device is code-compatible with F243/F241/C242 and instruction-set compatible with F240/C240. Functional pins are configurable as general-purpose I/Os (41 GPIOs), and JTAG-compliant scan-based emulation is integrated for in-circuit debugging. The modified Harvard architecture separates program and data buses, allowing simultaneous instruction fetch and data access for deterministic real-time behavior. Peripherals include SCI and SPI serial interfaces for system communication. The 3.3-V process reduces power dissipation compared to earlier 5-V C24x devices, simplifying thermal design in compact industrial controllers. Flash supports in-system programming for field firmware updates. Typical applications include digital motor control (AC induction, BLDC, and stepper motors), power conversion (inverters, UPS, SMPS), and industrial automation networks where the CAN bus provides robust communication. Event managers drive power stages with precisely phased, dead-band-protected PWM outputs. Design tip: decouple the 3.3-V rail thoroughly and route the JTAG port carefully for reliable emulation. TI community forums note this part is moving toward NRND, and there is no direct pin-compatible successor; new designs should consider newer C2000 C28x devices such as the TMS320F28027. This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for evaluating the TMS320LF2406APZA against modern C2000 C28x successors.

RFQ যোগাযোগ
TMS320LF2407APGEA - 16-Bit DSP 40MHz 64KB Flash MCU | Texas Instruments
TMS320LF2407APGEA

TMS320LF2407APGEA - 16-Bit DSP 40MHz 64KB Flash MCU | Texas Instruments

The Texas Instruments TMS320LF2407APGEA is a 16-bit fixed-point digital signal processor (DSP) from the C2000 C24x family, running at 40 MHz (40 MIPS) with 64KB (32K x 16) of on-chip flash memory, 2.5K x 16 data RAM, and a 3.3V supply, housed in a 144-pin LQFP (20x20 mm) package. A digital signal processor (DSP) is a specialized microprocessor optimized for real-time digital signal processing such as filtering, modulation, and closed-loop control. The TMS320LF2407APGEA belongs to the C2000 family of DSP microcontrollers, which occupy the control-focused branch of the broader microcontroller and embedded processor hierarchy. This hybrid architecture combines DSP math throughput with microcontroller peripherals, enabling single-chip implementation of high-performance control loops. Key features include the 16-bit C2xx core with a 32-bit accumulator and 16x16-bit hardware multiplier for single-cycle multiply-accumulate operations, two event managers (EVA and EVB) optimized for digital motor control, a CAN 2.0B communications module, SPI and SCI serial interfaces, up to 41 GPIO pins, a 10-bit ADC with 16 channels, a watchdog timer, and JTAG scan-based emulation for debugging. The flash memory supports in-system programming for field firmware updates. The enhanced TMS320 architecture delivers deterministic interrupt latency and fast context switching, essential for current-loop control in power electronics. Functional pins are configurable as general-purpose inputs/outputs (GPIOs) for maximum design flexibility. According to the TI TMS320LF2407A datasheet, the 240xA family also includes ROM devices that are fully pin-to-pin compatible with their flash counterparts, easing migration between volume builds. Typical applications include digital motor control (AC induction, BLDC, stepper), power conversion (inverters, UPS), industrial automation, and automotive networks using CAN. The event managers generate PWM with dead-band control for driving power switches, while the CAN module meets 2.0B specifications for networked systems. Design tip: decouple the 3.3V rail thoroughly and keep the ADC reference layout quiet; provide JTAG access for programming and debug. For new designs, TI recommends the higher-performance C2000 F28x generation such as the TMS320F2808 or TMS320F28335. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-10-11.

RFQ যোগাযোগ
TMS320LF6APZS - 16-Bit 40MHz DSP MCU | Texas Instruments
TMS320LF2406APZS

TMS320LF6APZS - 16-Bit 40MHz DSP MCU | Texas Instruments

The Texas Instruments TMS320LF2406APZS is a 16-bit fixed-point digital signal processor (DSP) microcontroller from the C2000 C24x family, operating at 40 MHz with 64KB (32K x 16) of on-chip Flash program memory and 5KB of data memory, housed in a 100-pin LQFP (PZS, 14x14 mm) package. The C24x generation integrates DSP throughput with microcontroller peripherals, enabling high-performance closed-loop digital motor control and power conversion in a single chip. It executes 40 million instructions per second (40 MIPS) while sustaining deterministic interrupt latency essential for real-time control loops. A digital signal processor (DSP) is a specialized microprocessor whose architecture is optimized for numeric-intensive algorithms such as the multiply-accumulate (MAC) operations that dominate motor-control, audio, and power-conversion math. The C2000 family sits at the intersection of microcontrollers and DSPs - inheriting deterministic interrupt and timer/peripheral infrastructure from the MCU world while exploiting the Harvard bus and hardware MAC of a DSP. Within the broader C2000 hierarchy, the LF240xA sits below the F28xx and F283xx floating-point generations and remains in production for cost-sensitive, fixed-point applications where the cycle budget comfortably fits within 40 MHz. Key features of the TMS320LF2406A include an event manager module optimized for three-phase PWM generation with dead-band insertion, a 10-bit ADC with conversion time suitable for current-sensing loops, CAN 2.0B interface, serial communications interface (SCI) and SPI ports, and a watchdog timer. The integrated peripherals remove the need for external logic to drive inverters or to digitize phase currents, lowering total BOM cost. The Flash-based LF2406APZS variant supports in-system reprogramming via JTAG, simplifying firmware iteration. Architecture-wise, the LF2406A uses a modified Harvard bus with separate program and data paths, six 16-bit auxiliary registers and an 8-level hardware stack, plus the C24x instruction set with single-cycle MAC. Power management includes 3.3V single-supply operation with on-chip voltage regulation, and several low-power modes are available. The 100-pin LQFP exposes GPIO, PWM channels, ADC inputs and serial buses while still fitting standard through-hole-friendly board outlines. Typical applications include digital motor control (BLDC, PMSM, AC induction, SRM drives), uninterruptible power supplies, solar inverters, automotive body and powertrain sub-systems, industrial automation variable-frequency drives, and switching power supply digital control loops. The on-chip event manager and ADC are tuned for 3-phase space-vector modulation at switching frequencies up to tens of kHz. When designing with the TMS320LF2406APZS, ensure that supply decoupling is placed within 5mm of each VDD/VSS pair, that analog and digital grounds are joined at a single point near the IC, and that JTAG lines are guarded against high-current switching traces. Compared with newer C2000 devices, code may need adaptation due to peripheral register differences. This page synthesizes distributor pricing, same- and cross-brand drop-in alternatives, lifecycle context, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
TMS5701224CPGEQQ1 - Hercules Safety MCU, 160MHz R4F, 1.25MB Flash | Texas Instruments
TMS5701224CPGEQQ1

TMS5701224CPGEQQ1 - Hercules Safety MCU, 160MHz R4F, 1.25MB Flash | Texas Instruments

The Texas Instruments TMS5701224CPGEQQ1 is an AEC-Q100 qualified automotive-grade 16/32-bit RISC Flash microcontroller built on the ARM Cortex-R4F floating-point core with lockstep safety architecture, delivered in a 144-pin LQFP (PGE) 20x20 mm package. It operates at up to 160 MHz, integrates 1.25 MB Flash and 192 KB SRAM with ECC on both memories, and provides dual 12-bit ADCs, multiple CAN, LIN, SPI and UART interfaces for ASIL-D capable automotive and industrial safety systems. A safety MCU (Microcontroller Unit) is a processor IC that integrates a CPU, Flash, SRAM and safety peripherals with built-in diagnostic and redundancy features designed to meet functional-safety requirements such as ISO 26262 (ASIL-D) or IEC 61508 (SIL 3). Within the broader system hierarchy, the TMS5701224CPGEQQ1 belongs to the MCU -> microcontroller -> embedded processor -> semiconductor IC category. It is engineered specifically for safety-critical applications where single-point faults must be detected and the system must remain in a safe state under hardware fault conditions. Key differentiating features include dual ARM Cortex-R4F CPUs operating in lockstep for fault detection, parity and ECC on Flash and SRAM, dedicated Built-In Self-Test (BIST) logic for CPU and memory, loopback capability on peripheral I/Os, an integrated Floating Point Unit (FPU), two 12-bit ADC modules with up to 24 channels, three CAN controllers, multiple LIN/UART/SPI/I2C ports, and an Enhanced Pulse Width Modulation (ePWM) module for motor and power-conversion control. From a technical depth perspective, the lockstep CPU compares outputs of two parallel cores cycle-by-cycle; any divergence triggers an error reaction within one clock, enabling ASIL-D systematic capability and hardware fault coverage. The ECC on Flash uses Single-Error Correction / Double-Error Detection (SECDED) while SRAM uses single-error correction for transient and permanent fault detection. The 1.25 MB Flash is split into a 1 MB program bank plus a 256 KB data Flash region for EEPROM emulation. Typical applications include automotive Electric Power Steering (EPS), Electronic Stability Control (ESC), Anti-lock Braking Systems (ABS), Advanced Driver Assistance Systems (ADAS) sensor fusion, Battery Management Systems (BMS), industrial Safety PLCs, and railway signaling where functional-safety certification is mandatory. When designing with this device, allocate a 4-layer PCB stackup with a continuous ground plane beneath the LQFP to dissipate the typical 1-2 W dissipation; route JTAG and trace signals on inner layers to avoid coupling on the safety island. Always use TI's SafeTI Diagnostic Library to validate IEC 61508 and ISO 26262 compliance claims for your end-equipment safety case. This page synthesizes distributor pricing, drop-in Hercules family alternatives, and practical design notes not consolidated in the TI datasheet alone, giving safety engineers a faster path from part selection to ASIL-D certification.

RFQ যোগাযোগ
TMS5701227CPGEQQ1 - 160MHz Cortex-R4F Dual-Core MCU | Texas Instruments
TMS5701227CPGEQQ1

TMS5701227CPGEQQ1 - 160MHz Cortex-R4F Dual-Core MCU | Texas Instruments

The Texas Instruments TMS5701227CPGEQQ1 is a high-performance automotive-grade 32-bit RISC flash microcontroller from the Hercules TMS570 safety MCU family, based on the ARM Cortex-R4F processor with a 160 MHz dual-core lockstep architecture and 1.25 MB of integrated flash plus 192 KB of data SRAM, housed in a 144-pin LQFP (PGE) package measuring 20 x 20 mm. A safety microcontroller (MCU) is a microcontroller designed for functional-safety-critical applications, integrating hardware diagnostics such as dual CPUs in lockstep, built-in self-test (BIST) for CPU and memory, ECC on flash and SRAM, and peripheral parity/loopback features. The TMS570 family occupies the high-end of TI's safety MCU portfolio alongside the RM4x series, and is widely used in chassis, braking, and body-domain automotive electronic control units that require ISO 26262 ASIL-D capability. Key features include dual ARM Cortex-R4F cores running in lockstep for fault detection, single-bit error correction and double-bit error detection (SECDED) on the 1.25 MB flash and 192 KB SRAM, an IEEE-754 compliant single-precision floating-point unit, integrated FlexRay and EMAC peripherals, an enhanced PWM (ePWM) module with trip-zone protection synchronized to the on-chip 12-bit MibADC, and a rich connectivity set including multiple CAN, SPI, LIN, and UART channels. The AEC-Q100 qualification ensures operation across the automotive -40C to +125C temperature range. The architecture supports up to 160 MHz system clock with separate instruction and data buses for deterministic execution, hardware floating-point acceleration reducing software overhead for control-loop math, and tightly-coupled memory for low-latency interrupt response - critical for real-time motor control and sensor-fusion loops. The FlexRay + EMAC combination makes the device equally well-suited to vehicle network nodes and industrial safety PLCs requiring deterministic Ethernet. Typical applications include automotive electronic stability control (ESC), electric power steering (EPS), anti-lock braking systems (ABS), battery management in hybrid and electric vehicles, and industrial servo drives. The on-chip floating-point unit accelerates field-oriented control (FOC) math, while the FlexRay interface suits time-triggered chassis networks, and the EMAC supports industrial Ethernet protocols such as EtherCAT or PROFINET. When designing with this device, allocate PCB area for the 144-pin LQFP thermal pad, route the JTAG/Trace 14-pin header for boundary-scan and code development, and ensure decoupling on each supply rail per the datasheet. The lockstep cores require software partitions that tolerate both cores reporting diverged diagnostics, and the SECDED-enabled flash must use TI's safe-RTI library for ASIL-D workflows. This page synthesizes distributor pricing for the TMS5701227CPGEQQ1, validated drop-in Hercules family alternatives, and practical design notes that go beyond the manufacturer datasheet.

RFQ যোগাযোগ
TUSB3210PM - USB 2.0 8052 Controller | Texas Instruments
TUSB3210PM

TUSB3210PM - USB 2.0 8052 Controller | Texas Instruments

The Texas Instruments TUSB3210PM is an integrated USB 2.0 full-speed general-purpose device controller with an 8052-based microcontroller, 8K x 8 RAM, and programmable general-purpose I/O in a 64-pin LQFP package. It supports USB data rates up to 12 Mbit/s and provides USB suspend, resume, and remote wake-up operation for connected peripheral, control, and human-interface-device designs. A USB general-purpose device controller is an application-specific microcontroller category that integrates a USB full-speed serial interface with embedded firmware execution and general-purpose I/O. The TUSB3210 sits within the hierarchy of semiconductor, embedded microcontroller, application-specific microcontroller, and USB interface controller devices. This integration reduces the need for a separate USB interface IC while retaining programmable behavior for product-specific USB functions. The principal feature set includes USB 2.0 full-speed compliance, a 12 Mbit/s supported USB data rate, suspend, resume, and remote wake-up support, and 8K x 8 bytes of RAM for application development. The controller also supports multiproduct designs with one code base and one controller, including configurations covering up to 16 products with one chip. Its programmability allows the same USB-connected platform to address multiple peripheral roles without relying on a fixed-function bridge. Internally, the TUSB3210 combines an 8052-compatible microcontroller with USB device-controller logic and general-purpose I/O. The 8K x 8 RAM organization provides 8,192 bytes of data storage for firmware variables, descriptors, buffers, and working state. Because the part is programmable rather than a fixed protocol translator, engineers can implement device-specific enumeration behavior, vendor requests, HID reports, status signaling, or other USB functions in one compact 64-LQFP device. Typical implementations include USB-to-serial adapters, keyboard and mouse controllers, industrial input modules, portable diagnostic equipment, programmers, and general USB I/O expansion boards. The 64-pin LQFP package also exposes enough pins for multiple GPIO functions, clocking connections, and USB bus-interface requirements, although a complete 64-pin pin map is not present in the supplied verified excerpts. The principal design consideration is that USB firmware, descriptor development, and bus-routing validation remain necessary because this is a programmable controller rather than a fully finished USB peripheral. Layout should follow the manufacturer's recommended USB data-path guidance, provide clean return-current paths, and use appropriate decoupling. Exact operating-voltage, clock, temperature, and pin-function details should be confirmed in the manufacturer datasheet before schematic release. This page consolidates the verified distributor identification, USB 2.0 and 8052 controller description, package information, RAM capacity, pricing indication, and sourcing links into an engineering-focused view. It also separates verified facts from unavailable detailed specifications and documents why few defensible drop-in replacements can be confirmed from the supplied cross-reference results.

RFQ যোগাযোগ
UM9830 - Microchip EOL Component | Discontinued Part
UM9830

UM9830 - Microchip EOL Component | Discontinued Part

The Microchip UM9830 is a discontinued component originally manufactured by Microchip Technology, classified by manufacturer product change notice MFOL-19MRQH667 as obsolete effective 2025-06-26 with no further supply and no suggested replacement. According to the referencesource.org EOL mapping entry dated 2026-08-03, the UM9830 belongs to a family of discontinued Microchip parts (alongside UM9369, UM9921, UM7006B, UM9993, UM9301, and UM4306B) that have reached end-of-life status without direct successor parts. Because no functional successor has been specified by the manufacturer, any second-source strategy must be designed at the board level rather than at the part level. This part entered the obsolete category effective immediately on 2025-06-26 and has no last-time-buy window or last-ship date; existing inventory is the only remaining source. A web search for this exact MPN on distributor sites returns generic MicrochipDirect landing pages without parametric content, meaning specific electrical parameters, package information, and qualification data for the UM9830 are not publicly indexed. Engineers requiring the original functionality of this part should treat any remaining stock as sole-source and should plan a board-level redesign rather than pursue a drop-in replacement. Key facts about this listing: the manufacturer is Microchip Technology, the lifecycle status is obsolete as of mid-2025, the product change notice identifier is MFOL-19MRQH667, and no alternate or suggested replacement MPN exists in the public Microchip cross-reference catalog. Procurement teams should treat remaining inventory as legacy stock and validate each lot against the original design specification before assembly. Where this part was used in long-lifecycle programs, distributors carrying remaining stock may be the only legal supply path. This page synthesizes the publicly available lifecycle information, the Microchip product change notice reference, and practical procurement guidance that the manufacturer has not consolidated into a single datasheet. Because the UM9830 has no published parametric specification indexed in the public web (only an EOL notice), the spec table below is intentionally sparse and uses [DATA_NEEDED] markers wherever Microchip's internal documentation would normally supply values. Engineering teams should contact Microchip directly or reference internal design archives for original parameter sets.

RFQ যোগাযোগ
UPD78F0532AGB-GAH-AX - 8-Bit 20MHz 24KB Flash MCU | Renesas
UPD78F0532AGB-GAH-AX

UPD78F0532AGB-GAH-AX - 8-Bit 20MHz 24KB Flash MCU | Renesas

The Renesas UPD78F0532AGB-GAH-AX is an 8-bit CISC microcontroller from the 78K0/Kx2 family, featuring 24KB (24K x 8) of on-chip Flash program memory and a maximum operating frequency of 20MHz. Housed in a 64-pin LQFP package, the device operates from a 1.8V to 5.5V supply range (5V specified in the automotive-grade part variant) and integrates a rich peripheral set including timers, A/D converter, serial interfaces, and interrupt controllers typical of the 78K0/Kx2 family. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for cost-sensitive, low-power embedded control. Within the broader taxonomy, 8-bit MCUs belong to microcontrollers -> embedded processors -> semiconductor ICs. The 78K0/Kx2 family from Renesas specifically targets compact, low-power general-purpose applications using a CISC (Complex Instruction Set Computer) architecture with an instruction set tuned for code density and deterministic interrupt response, distinguishing it from RISC-based 8-bit families such as 8051 or AVR. Key features include 24KB of Flash memory for application code and data storage, 1KB of on-chip RAM (typical of this family), an integrated 10-bit A/D converter, multiple 16-bit timers, UART and CSI serial interfaces, and a programmable watchdog timer. The device supports both 3V and 5V operation, providing flexibility for battery-powered and industrial systems. The 64-pin LQFP package offers 60+ GPIO pins for interfacing with sensors, displays, and actuators. The 78K0/Kx2 architecture employs a CISC instruction set with variable-length instructions (1-6 bytes) and a hardware multiplier, achieving efficient code density for embedded applications. The integrated Power-On Reset (POR), Low-Voltage Detection (LVD) circuit, and on-chip debug interface simplify system design and reduce external component count. The part is qualified for the automotive operating temperature range (-40C to +85C or -40C to +125C depending on variant), making it suitable for harsh environments. Typical applications include automotive body control modules, HVAC controllers, instrument clusters, industrial sensor interfaces, consumer white goods, and small home appliances. The combination of Flash memory, low power consumption, and the robust 78K0 instruction set makes this MCU well-suited for cost-sensitive motor control and sensor signal processing tasks. When designing with this device, ensure that the on-chip regulator bypass capacitors are placed close to the VDD/VSS pins, and that unused I/O pins are configured as outputs or pulled to defined logic levels to minimize power consumption. The Flash memory write/erase cycles require a minimum operating voltage of 2.7V; for battery-backed designs, plan for brown-out detection. This page synthesizes distributor availability, drop-in alternatives from the 78K0/Kx2 family, and practical design notes not found on standard distributor listings.

RFQ যোগাযোগ
USB2005-MN-01 USB 2.0 ATA/ATAPI Controller | Microchip
USB2005-MN-01

USB2005-MN-01 USB 2.0 ATA/ATAPI Controller | Microchip

The Microchip Technology USB2005-MN-01 is an application-specific USB 2.0 ATA/ATAPI controller used to bridge a Universal Serial Bus host interface with an IDE storage device. The verified distributor records identify the device as a microcontroller-class integrated circuit associated originally with SMSC and list it for electronic procurement and reference. Its defining functional parameters are USB 2.0 host connectivity and ATA/ATAPI device support; no complete manufacturer electrical table was included in the supplied data, so details such as transfer rate, supply voltage, clock frequency, and pin assignments remain unverified. An application-specific controller is a specialized semiconductor that integrates the logic required for a particular external interface or system function. In the USB 2.0 ATA/ATAPI category, this device belongs to the broader hierarchy of controller IC, interface IC, embedded controller, and semiconductor. Its role is more specialized than a general-purpose microcontroller because the controller is designed around the command, signaling, and data-path requirements of connecting USB storage equipment to an ATA/ATAPI bus. The primary verified feature is support for the USB 2.0 and ATA/ATAPI standards. A USB 2.0 host interface can use this controller when a system needs to operate compatible ATA storage through a USB connection rather than a conventional internal IDE interface. The listing also classifies USB2005-MN-01 as an application-specific microcontroller, distinguishing it from generic logic, memory, and power-management components. Its USB-to-storage positioning makes it relevant to legacy storage adapters, embedded systems, and equipment requiring an operating-system-visible USB mass-storage path. Engineering use requires careful verification before schematic capture. The supplied records do not provide the exact package designation, exposed-pad requirements, pinout, clocking method, regulator architecture, or power-consumption limits. They also do not establish whether the device supports SATA, external power, hot-plug handling, bus-powered media, or particular USB suspend and wake behaviors. Those capabilities must be confirmed from the complete manufacturer datasheet and errata before USB signal routing, storage-interface timing, or PCB layout is finalized. Typical applications include USB-to-ATA storage adapters, embedded data-logging equipment, industrial controllers with legacy disk storage, service and test systems for older IDE devices, and computer peripherals that retain ATA/ATAPI connectors. The device should be evaluated where a host must communicate with a compatible ATA/ATAPI target through USB 2.0 while preserving the established command set and storage-device behavior. The primary design caution is that a USB 2.0 label alone does not establish present-day performance or compatibility. Engineers should verify supported USB speed modes, maximum transfer rate, enumeration behavior, ATA timing, cable length, and media-power requirements. Board design should also reserve space for the verified package, decoupling network, USB data routing, ATA signal conditioning, and any required external storage power. This page consolidates verified distributor pricing, a function-oriented technical summary, procurement guidance, comparison limits, and practical design cautions. It distinguishes confirmed USB 2.0 ATA/ATAPI functionality from unverified electrical details so engineers can assess suitability without mistaking catalog summaries for a complete datasheet specification.

RFQ যোগাযোগ
USB2228AHZS07 USB 2.0 Flash Media Controller | SMSC
USB2228AHZS07

USB2228AHZS07 USB 2.0 Flash Media Controller | SMSC

The SMSC USB2228AHZS07 is an application-specific microcontroller configured as a fourth-generation USB 2.0 flash media controller with an integrated card interface. It is identified in the 26-page USB2228 datasheet and is supplied in an unspecified surface-mount package. Its core role is to provide a USB host-facing storage interface for flash-memory cards, combining USB connectivity, media-card control, and configuration logic in one integrated circuit. An application-specific microcontroller is a specialized semiconductor optimized for a defined set of system functions rather than general-purpose software execution. Within the product hierarchy, this device belongs to the microcontroller and embedded-controller class, while its specific application places it in the flash media controller category. This integration can reduce the number of discrete components required between a USB port and a removable flash card. The fourth-generation controller architecture identifies the USB2228 family as a dedicated USB 2.0 storage solution. USB 2.0 provides a standardized host-to-controller interface, while the integrated card functionality manages communication with supported removable flash media. The part is specifically listed by Rochester Electronics as an application-specific microcontroller from SMSC, and market listings associate the device with a 26-page manufacturer datasheet. Designing with this controller requires attention to the USB host interface, card electrical requirements, supported media formats, embedded firmware, and the exact package dimensions. Because the device is application-specific, its operational behavior is typically determined by its internal firmware and board configuration rather than by a general-purpose processor application. Designers should preserve the reference network, clocking arrangement, power sequencing, and card-detection implementation used by the manufacturer. Typical uses include USB flash-card readers, card-reader appliances, portable storage accessories, embedded storage gateways, and host systems that require direct access to removable flash media. In each case, the controller handles the USB-to-card interface while the surrounding circuit supplies regulated power, termination, protection, and the physical media connector. The principal design trade-off is integration versus upgrade flexibility. A dedicated flash media controller can simplify the USB storage path, but it is less versatile than a general-purpose microcontroller. Validate the supported card types, transfer modes, firmware configuration, package land pattern, and signal-routing requirements before releasing a new PCB layout. This product record combines the exact USB2228AHZS07 identification, manufacturer description, package-related uncertainty, verified source links, and application-oriented engineering guidance. It also separates confirmed attributes from parameters that require confirmation against the manufacturer datasheet, helping engineers plan sourcing and hardware review without obscuring unresolved design assumptions.

RFQ যোগাযোগ
W55RP20 - RP2040+W5500 Ethernet SiP MCU | WIZnet
W55RP20

W55RP20 - RP2040+W5500 Ethernet SiP MCU | WIZnet

The WIZnet W55RP20 is a System-in-Package (SiP) ioMCU that integrates the Raspberry Pi RP2040 dual-core Arm Cortex-M0+ microcontroller running at 133 MHz with the W5500 hardware TCP/IP Ethernet controller, in a 68-pin VFQFN exposed-pad package. It combines 2 MByte of on-chip flash memory and 264 kB of on-chip SRAM organized in six independent banks with a full hardwired TCP/IP stack and a 12-channel DMA controller. A System-in-Package device stacks or side-by-side mounts two dies within a single molded package, so the W55RP20 functions electrically as one microcontroller with built-in Ethernet, eliminating the two-chip RP2040-plus-W5500 solution that previously required separate routing, crystals, and power domains. In the product hierarchy it sits as: ioMCU -> communications controller microcontroller -> Ethernet microcontroller -> IoT connectivity IC. Key features include the dual Cortex-M0+ cores at 133 MHz, 2 MB flash for code storage, 264 kB SRAM in six independent banks, and the W5500 subsystem with a hardwired TCP/IP stack supporting 8 hardware sockets, which offloads protocol processing entirely from the CPU. A 12-channel DMA controller supports memory-to-peripheral, peripheral-to-memory, and memory-to-memory transfers, each channel with its own control and status registers, letting the processor switch to other tasks or low-power states during large data transfers. The W5500 die provides a hardware TCP/IP stack implementing MAC and PHY functionality for 10/100 Mbps Ethernet, so networking is deterministic and does not consume MCU cycles for protocol handling. This architecture suits applications where wire-speed throughput and low jitter matter more than a large software network stack. Typical applications include industrial IoT gateways, networked sensor nodes, smart-building controllers, and Ethernet-enabled embedded systems where developers want Raspberry Pi Pico-class processing plus native wired networking in one chip. Design consideration: as a SiP, thermal dissipation is combined from both dies; verify total power budget and provide adequate ground-plane copper under the exposed pad for heat spreading and signal return. This page synthesizes distributor pricing, availability, evaluation-board references, and practical design notes not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ
W55RP20-S2E - Serial-to-Ethernet MCU, 2MB Flash | WIZnet
W55RP20-S2E

W55RP20-S2E - Serial-to-Ethernet MCU, 2MB Flash | WIZnet

The WIZnet W55RP20-S2E is a pre-programmed serial-to-Ethernet communications controller microcontroller IC built on the W55RP20 System-in-Package, delivering a dual ARM Cortex-M0+ core at 133 MHz, 2MB on-chip Flash, and a hardwired 10/100 Mbps Ethernet TCP/IP controller in a 68-pin VFQFN package with exposed pad. Each unit ships with WIZnet serial-to-Ethernet (S2E) firmware and a unique MAC address from the WIZnet OUI block. An application-specific communications microcontroller, or ioMCU, is a device that combines a general-purpose MCU core with dedicated network hardware. In the W55RP20-S2E, the integration hierarchy runs: serial-to-Ethernet chip -> communications controller MCU -> Ethernet IC -> power/networking semiconductor. Unlike software TCP/IP stacks that consume MCU cycles, the integrated W5500-style hardwired TCP/IP core offloads protocol processing in silicon. Key features include the SiP integration of Raspberry Pi's RP2040 microcontroller and WIZnet's W5500 Ethernet controller, 264kB on-chip SRAM organized in six independent banks, a 12-channel DMA controller supporting memory-to-peripheral, peripheral-to-memory, and memory-to-memory transfers, and a USB 2.0 full-speed (12 Mbps) controller usable as host or device. The serial-to-Ethernet firmware supports serial speeds up to 921,600 bps, letting any UART-equipped device gain Ethernet connectivity without protocol development. The dual Cortex-M0+ architecture lets one core handle application logic while the other manages network I/O, and the hardwired TCP/IP stack supports 8 independent sockets with minimal latency. Because the TCP/IP, MAC, and PHY functions are hardened in silicon, software stack bugs and CPU load from protocol handling are essentially eliminated. Typical applications include adding Ethernet to legacy industrial equipment with UART ports, IoT smart-device connectivity, and networked sensor or control nodes. The pre-programmed firmware approach removes firmware certification and development risk for serial-to-Ethernet designs. Design consideration: since this is a pre-programmed part, use the bare W55RP20 if custom firmware is required; the S2E variant is optimized for UART-to-Ethernet bridging with minimal development effort. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
W681308DG - USB Audio Controller 16-bit 48-LQFP | Nuvoton
W681308DG

W681308DG - USB Audio Controller 16-bit 48-LQFP | Nuvoton

The Nuvoton W681308DG is a USB audio controller IC with an integrated 16-bit audio codec, housed in a 48-pin LQFP (7x7 mm) surface-mount package. As a member of the Winbond/Nuvoton W6813 series of USB audio controllers, it integrates a USB controller, audio codec, and embedded microcontroller into a single chip for USB audio peripheral designs. A USB audio controller is a mixed-signal device that implements the USB audio class protocol on the digital side and an audio codec (codec = coder-decoder) on the analog side. Within the system hierarchy, it sits between a general-purpose USB microcontroller and a dedicated audio codec: it handles USB enumeration, audio streaming, clocking, and sample-rate conversion, while also providing microphone and speaker signal paths. This integration reduces bill-of-materials count compared to a discrete USB MCU plus external codec solution. Key features of the W681308DG include a 16-bit audio data path, USB full-speed audio transport, integrated microphone and speaker audio channels, and a compact 7x7 mm 48-LQFP footprint that supports consumer peripheral form factors. The device operates from a 3.3 V supply, consistent with the family datasheet description of the W681308 series as a 3.3 V part. Architecturally, the W681308 combines an 8-bit CISC microcontroller core with on-chip program memory and a hardwired USB audio function block. The codec front end handles anti-aliasing filtering, ADC for microphone inputs, and DAC for speaker outputs, while the MCU firmware manages HID interfaces, mute/volume controls, and other USB descriptor behavior. Refer to the manufacturer datasheet for precise clock, PLL, and interface specifications. Typical applications include USB headset and headphone amplifiers, desktop microphone arrays, USB speakerphones, VoIP handsets, and general USB audio dongles where a single-chip, low-cost USB audio solution is required. A key design consideration is analog layout: the microphone preamp and DAC outputs are sensitive to digital return-path noise, so a solid ground plane, careful separation of analog and digital traces, and proper decoupling of the 3.3 V rail per the manufacturer datasheet recommendations are essential for a low-noise result. This page synthesizes distributor sourcing data, datasheet references, and practical design notes not found in the manufacturer datasheet.

RFQ যোগাযোগ
W77C032A40FL - 40MHz 8-Bit ROMless MCU | Nuvoton
W77C032A40FL

W77C032A40FL - 40MHz 8-Bit ROMless MCU | Nuvoton

The Nuvoton W77C032A40FL is a ROMless Turbo-51 8-bit microcontroller operating at up to 40 MHz, with 1K x 8 bits of RAM, 36 I/O pins, and a 44-pin BQFP package. Designed for embedded control applications, the device combines a high-clock-speed 8051-compatible core with an internal oscillator, allowing designers to build compact control systems without adding an external program-memory device. An 8-bit microcontroller is a semiconductor integrated circuit containing a central processing unit, memory, I/O ports, and peripheral functions on one package. In the product hierarchy, it belongs to the microcontroller family of embedded processors and embedded ICs. The W77C032A40FL belongs to the Turbo-51 family and uses a ROMless architecture, meaning program storage must be supplied by external memory while working data can be held in its internal RAM. Key characteristics include a maximum clock frequency of 40 MHz, 1K x 8-bit SRAM, and 36 general-purpose I/O lines. Its internal oscillator reduces the external clock-component count, while the 44-BQFP package exposes substantially more I/O than smaller dual-inline or small-outline packages. These characteristics make the MCU appropriate for compact controllers with multiple discrete inputs and outputs, particularly where an 8051-compatible instruction set and external program memory are required. The W77C032A40FL is positioned as a ROMless Turbo-51 device rather than a self-contained MCU with embedded Flash. External program memory and interface circuitry therefore influence the complete memory system. Its 36 I/O pins provide ample connectivity for control signals, indicators, relays, sensors, and communication peripherals. Because the device is specified at 40 MHz, firmware timing, memory-access delays, peripheral clock requirements, and external-memory interface timing must be reviewed together during schematic and PCB design. Typical applications include industrial machine controls, building-control modules, appliance controllers, interface modules, and other embedded automation products. The combination of 36 I/O, internal RAM, and external program-memory support is especially useful when a product needs substantial I/O breadth but limited on-chip volatile memory. The MCU can act as the supervisory controller between sensors, actuators, communications circuitry, and discrete logic. A key design consideration is that ROMless operation requires careful implementation of the external memory interface and correct timing for the selected memory device. Place decoupling close to the supply pins, route oscillator and memory signals consistently, and keep high-current switching nodes away from sensitive control inputs. Confirm pin multiplexing, reset behavior, and peripheral availability against the manufacturer datasheet before finalizing firmware and board connections. This page consolidates the principal electrical, memory, package, sourcing, and replacement information for W77C032A40FL. It also provides practical application guidance and design checks that help engineers determine whether this ROMless Turbo-51 MCU fits a control design before committing to PCB layout and external-memory implementation.

RFQ যোগাযোগ
W77C032A40PL - 40MHz ROMless 8051 MCU | Nuvoton
W77C032A40PL

W77C032A40PL - 40MHz ROMless 8051 MCU | Nuvoton

The Nuvoton Technology Corporation W77C032A40PL is an 8-bit ROMless 8051-compatible microcontroller operating at up to 40 MHz, with 1 KB x 8 RAM, 36 I/O lines, and a 44-pin PLCC package. The device uses the W77C032 Turbo-51 processor architecture, which reduces wasted instruction cycles and executes 8051 instructions approximately 1.5 to 3 times faster than a traditional 8051 core at the same clock speed. A microcontroller is a programmable semiconductor integrating a processor core, memory, I/O ports, timers, serial communications, and interrupt functions on one integrated circuit. The W77C032 belongs to the 8-bit MCU hierarchy and retains 8052 pin and instruction-set compatibility. Because the part is ROMless, application firmware must be supplied through external program-memory hardware, making the device suitable for systems that require flexible code storage, boot loading, field updating, or shared memory among several devices. The principal specifications include a 40 MHz maximum operating speed, 1 KB x 8 internal RAM, four 8-bit I/O ports, 36 total I/O lines, and an internal oscillator. The W77C032 also incorporates standard 8052 resources, including three 16-bit timer/counters, a full-duplex serial port, and multiple interrupt sources. Its 4.5 V to 5.5 V operating range and 44-PLCC package support established 5 V embedded-control architectures where a leaded, socket-compatible footprint is preferable to a fine-pitch surface-mount package. The redesigned processor core avoids wasted clock and memory cycles, improving execution efficiency without changing the familiar 8051 instruction set. This combination is useful when maintaining legacy 8051 source code while increasing control-loop or peripheral-handling performance. Since the MCU has no on-chip program memory, a system designer must account for external ROM or another memory source when creating the memory map, boot sequence, and firmware-loading architecture. Typical uses include industrial controllers, embedded data-acquisition equipment, communications controllers, legacy 8051 peripheral upgrades, and compact automation modules. The 36 I/O lines provide substantial parallel-interface capacity, while the timers and serial port reduce the need for external peripheral chips. Board-level designs should also provide a stable clock or oscillator arrangement, external program-memory interfacing, suitable decoupling, and adequate pin-compatible routing. A key design consideration is that the PLCC package has 44 positions, but the verified product records do not provide a complete numbered pin description. Engineers should therefore assign the PCB footprint and nets directly from the pin table and package drawing in the manufacturer data sheet rather than inferring connections from generic 8051 diagrams. Confirm the external-memory interface, reset behavior, clock requirements, and available I/O before finalizing the board layout. This product summary consolidates the confirmed architecture, memory, clock, package, sourcing, and lifecycle information with engineering guidance for external-memory implementation, firmware compatibility, and PLCC layout. It also distinguishes directly documented characteristics from parameters that still require confirmation from the complete manufacturer data sheet.

RFQ যোগাযোগ
W77E058A40FL - 40MHz 8051 32KB Flash MCU | Nuvoton
W77E058A40FL

W77E058A40FL - 40MHz 8051 32KB Flash MCU | Nuvoton

Nuvoton Technology Corporation W77E058A40FL is an 8-bit CMOS W77-series microcontroller with 32 KB of embedded Flash memory, a 40 MHz operating frequency, and a 44-BQFP package. It uses a four-clock machine-cycle 8051-compatible architecture and operates from a 5 V supply, combining legacy MCS-51 software compatibility with substantially faster instruction execution than the original standard 80C51 family. An 8051-compatible microcontroller is an embedded processor designed around the MCS-51 instruction set and its associated register, interrupt, timer, serial-interface, and port architecture. The W77 series places that established software ecosystem within the broader hierarchy of embedded controllers, 8-bit microcontrollers, and general-purpose semiconductor devices. This makes it useful for control systems that benefit from established 8051 tools and code while requiring higher processing throughput and integrated Flash rather than an external program-memory device. The W77E058A40FL combines several headline characteristics: 8-bit processing, 40 MHz operation, and 32 KB of embedded Flash. Its four-clock machine-cycle design executes each machine cycle in a quarter of a full 40 MHz clock period. The device also provides four 8-bit I/O ports and follows the MCS-51 instruction set, allowing engineers to reuse familiar driver concepts and peripheral-control code while selecting a faster Flash-based implementation. Technically, the part belongs to the W77 family and is positioned as a compact, 5 V embedded controller. Its Flash memory consolidates program storage on the die, simplifying the hardware arrangement compared with an architecture that requires external program memory. Because the controller remains compatible with the MCS-51 instruction set, software migration from an appropriate 80C52-class design can be easier than moving to a different instruction set. Board compatibility still requires verification of pin functions, electrical limits, memory organization, and peripheral availability. Typical applications include industrial keypad and panel controllers, motor and relay-sequencing modules, compact instrumentation, appliance-control boards, and legacy 8051 peripheral upgrades. The 40 MHz execution rate can improve responsiveness in polling loops, protocol handling, and time-dependent control tasks, while the four 8-bit I/O ports support digital input, output, and external-interface connections when the remaining pins provide the required clock, reset, and power functions. A key design consideration is that pin-compatible software does not automatically prove drop-in electrical compatibility. Before replacing an existing 8051 device, verify the 44-BQFP footprint, pin assignments, reset behavior, operating voltage, oscillator connections, I/O drive limits, and peripheral functions against the current datasheet. Programming and development-tool requirements should also be checked because instruction-set compatibility does not guarantee that every legacy programmer supports the device. This product page combines the W77E058A40FL's core specifications, verified component listings, application guidance, design checks, and a transparent comparison of candidate cross-reference devices. It also distinguishes confirmed drop-in options from merely similar controllers, helping engineers make a replacement decision without relying on package similarity alone.

RFQ যোগাযোগ
W77E058A40PL - 40MHz 8051 MCU, 32KB Flash | Nuvoton
W77E058A40PL

W77E058A40PL - 40MHz 8051 MCU, 32KB Flash | Nuvoton

Nuvoton Technology Corporation W77E058A40PL is an 8-bit CMOS 8051-compatible microcontroller operating at up to 40 MHz, with 32KB of Flash memory in a 44-pin PLCC package. It executes four clocks per machine cycle, provides two UART devices and two DPTR registers, and operates from a 5 V supply across the 4.5 V to 5.5 V range. The W77E058A family is also pin-compatible with traditional 12T 8051 devices. An 8051 microcontroller is an embedded-computing IC that combines a CPU core, program memory, data memory, I/O ports, and peripherals on one integrated circuit. Within the product hierarchy, the W77E058A is an 8-bit MCU, a 4T 8051 MCU, a member of the MCS-51 instruction-set family, and a member of the broader embedded processor and semiconductor categories. Its 8051 compatibility supports established compiler, debugger, and application-development ecosystems. Key features include a 40 MHz maximum operating frequency, a four-clock machine-cycle architecture, and 32KB of on-chip Flash organized as 32K by 8 bits. Two UART devices support serial communication, while two DPTR registers provide separate 16-bit pointer contexts. Four 8-bit I/O ports support digital interfaces, and the 4.5 V to 5.5 V operating range aligns the device with conventional 5 V embedded equipment. The device uses an 8-bit CISC architecture compatible with the MCS-51 instruction set and remains compatible with traditional 12T 8051 interfaces. Its 4T architecture reduces the clock-to-machine-cycle ratio to four clocks, allowing 40 MHz operation without changing the fundamental software timing model. Because the product is identified as NRND, engineers should verify availability and consider the manufacturer's current portfolio before starting a new design. Typical applications include security and alarm systems, communication equipment, industrial control, power-management controllers, and industrial personal computers. The two UARTs are useful for sensor, transceiver, display, or host serial links, while the four parallel I/O ports can handle digital control signals, status indicators, relay logic, or keypad interfaces. The principal design consideration is the 5 V supply requirement and the limited 0°C to 70°C temperature range. Decoupling and signal-integrity practices remain important because all peripherals share the same supply and ground system. Engineers should also confirm the PLCC-44 footprint, pin assignments, and board-level clearances against the manufacturer datasheet before layout release. This page combines the manufacturer's family-level architecture and lifecycle information with distributor specifications and a practical replacement assessment. It also identifies the package, programming interface considerations, application fit, and design checks needed to evaluate the W77E058A40PL in an embedded control platform.

RFQ যোগাযোগ
W77E516A40FL - 40MHz 8051 MCU 64KB Flash | Nuvoton
W77E516A40FL

W77E516A40FL - 40MHz 8051 MCU 64KB Flash | Nuvoton

Nuvoton Technology Corporation W77E516A40FL is an 8-bit 8051-compatible microcontroller operating at 40 MHz with 64 KB of embedded Flash program memory in a 44-pin PQFP package. The device includes four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex serial port, and interrupt resources inherited from the standard 8052 architecture. Its redesigned processor core removes wasted clock and memory cycles, allowing typical instructions to execute approximately 1.5 to 3 times faster than a traditional 8051 at the same crystal frequency. An 8051-compatible microcontroller is an embedded control processor that retains the classic 8051 instruction set while adding a redesigned execution core and modern integrated Flash memory. The W77E516 belongs to the 8-bit microcontroller hierarchy, where Flash program memory replaces externally attached ROM and supports compact, self-contained control systems. This combination makes the device suitable for industrial controllers, communication equipment, data-acquisition modules, and legacy equipment upgrades where existing 8051 software can be retained. The principal specifications are a 40 MHz operating speed, 64 KB of 64K x 8 Flash program memory, 1 KB of 8-bit RAM, 36 I/O lines, and a 5 V supply. Its 8052-compatible architecture provides four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex UART, and multiple interrupt sources. The redesigned core improves instruction throughput without requiring a change to the standard 8051 instruction set, which helps designers reuse established firmware and peripheral-driver routines. Program execution benefits from a processor architecture that avoids wasted memory and clock cycles. Because the device is instruction-set compatible with the 8052, software can use standard 8051 development tools while taking advantage of the faster core. The integrated Flash memory consolidates program storage onto the device, reducing system-level component count and allowing firmware updates to be handled without a separate external memory device. Typical applications include industrial control panels, serial-interface adapters, test and measurement instruments, embedded data collectors, and communication modules. The 36 available I/O lines support peripheral connections, while the timer/counter and serial resources reduce the need for external interface components. The device is also appropriate for maintaining older 8051-based products where software compatibility is more valuable than migration to a different instruction set. The main design consideration is that the W77E516A40FL is an 8-bit, 5 V device rather than a low-power 3.3 V or modern 32-bit controller. Board designs should provide the specified 5 V operating supply, correct decoupling, and a stable clock source. Verify oscillator requirements, absolute maximum ratings, and timing margins in the manufacturer datasheet before laying out a new PCB, especially when replacing an electrically different original MCU. This page combines the manufacturer technical description, distributor specifications, packaging information, and practical guidance for evaluating the W77E516A40FL in 8051-compatible designs. It also identifies the scarcity of verified pin-compatible substitutes, providing a drop-in cross-reference candidate without presenting unverified components as equivalent parts.

RFQ যোগাযোগ
W77E532A40PL - 40MHz 8051 128KB Flash MCU | Nuvoton
W77E532A40PL

W77E532A40PL - 40MHz 8051 128KB Flash MCU | Nuvoton

The Nuvoton Technology Corporation W77E532A40PL is a 40 MHz, 8-bit 8051-compatible microcontroller with 128KB of program Flash, 1KB of RAM, 36 general-purpose I/O pins, and a 44-pin PLCC package. It operates from a single 5 V supply and executes the standard 8051 instruction set in a four-cycle architecture. An 8051-compatible microcontroller is an embedded controller that retains the classic 8051 programming model and peripheral structure while using an internally redesigned processor core. The W77E532A belongs to the W77 family of enhanced 8051 devices, providing compatibility with 8052 software and the hardware resources expected from a standard 8052, including four 8-bit I/O ports, three 16-bit timer/counters, a full-duplex serial port, and interrupt sources. Key device characteristics include a 40 MHz operating speed, 128KB of Flash program memory, 1KB of internal RAM, and 36 I/O pins. The redesigned core removes wasted clock and memory cycles, allowing instructions to complete approximately 1.5 to 3 times faster than a traditional 8051 at the same crystal frequency. A 5 V supply and 44-pin J-lead PLCC package make the device suitable for established embedded control platforms rather than new high-density mixed-signal designs. The W77E532A architecture remains instruction-set and 8052 pin compatible while improving execution efficiency. Its 128KB Flash area provides substantially more program storage than many classical 8051 controllers, reducing the need for external program memory in larger control routines. Integrated timers support periodic timing, event counting, and modulation tasks, while the serial port handles low-speed communication with external controllers or data acquisition modules. Typical uses include industrial controllers, data acquisition equipment, communications interfaces, embedded instrumentation, and legacy 8051 system upgrades. The device can also serve as a bridge between an established 8051 software base and a newer PCB revision, provided the board footprint, supply rail, oscillator arrangement, and peripheral assignments match the original controller. When designing around the W77E532A40PL, confirm the 5 V supply tolerance, external crystal or clock connection, Flash programming method, and reset configuration against the manufacturer datasheet. Because the PLCC package is legacy-oriented, it is less convenient than an LQFP or QFP package for automated assembly, hand soldering, or compact consumer products. This page consolidates device specifications, package information, application guidance, and verified same-footprint alternatives into a practical engineering reference. It also highlights where an engineer must confirm pin mapping, timing, and supply requirements before treating a candidate as a functional replacement.

RFQ যোগাযোগ
W77IC32A25PL - 25MHz ROMless 8051 MCU | Nuvoton
W77IC32A25PL

W77IC32A25PL - 25MHz ROMless 8051 MCU | Nuvoton

Nuvoton Technology Corporation W77IC32A25PL is an 8-bit ROMless W77 Turbo-51 microcontroller operating at 25 MHz, with 1K x 8 RAM, 36 I/O lines, and a 44-pin PLCC package. It is intended for embedded 8051-compatible control systems that require an external program-memory device while retaining a conventional 8-bit MCU architecture. A ROMless 8051 microcontroller is a variation of the MCS-51 microcontroller family in which the program memory is not integrated on the chip. The processor executes its firmware from external memory, allowing application-specific code capacity to be selected during system design. Within the semiconductor hierarchy, W77IC32A25PL belongs to the 8-bit microcontroller class, the broader embedded-processing category, and ultimately the microcontroller and semiconductor ecosystems. The device combines a 25 MHz clock with a 1K x 8 internal RAM array and 36 input/output lines. Its ROMless architecture is useful when firmware must exceed internal program-memory limits, when multiple products share the same external-memory configuration, or when code updates are managed outside the MCU. The -40°C to +85°C operating-temperature range supports industrial-temperature equipment while retaining compatibility with the established 8051 instruction set and peripheral environment. Technically, the W77 family is positioned as a Turbo-51 implementation, meaning that its clock rate is higher than that of the original 12 MHz 8051 class. At 25 MHz, the device offers greater instruction throughput than standard 8051 parts, although actual application performance depends on bus timing, wait states, external-memory access, and the selected memory architecture. The ROMless design makes external address decoding and code-memory interfacing central parts of the hardware design rather than optional functions. Typical uses include industrial controllers, appliance interfaces, embedded data-acquisition equipment, legacy 8051 peripheral boards, and control modules upgraded from slower standard 8051 processors. The broad I/O count allows the MCU to connect switches, displays, relays, sensors, and communication interfaces while the external program-memory bus accommodates larger firmware images. Designers should also account for the external memory interface timing when calculating system-level operating margins. PCB implementation requires a 44-pin PLCC land pattern, careful routing of the external program-memory bus, and decoupling close to the supply pins. Because the PLCC package is not represented by a dedicated diagram key in the XAIPART package library, use the manufacturer package drawing and pin-description table when assigning tracks. Confirm oscillator, reset, I/O, and memory-bus requirements against the manufacturer datasheet before releasing a layout. This product page combines the verified device identity, package and timing information, application guidance, drop-in comparison limits, and practical implementation cautions. It helps engineers determine whether the W77IC32A25PL fits a new 8051 design or whether an existing board requires qualified substitution and software validation.

RFQ যোগাযোগ