Logic ICs
بەرهەمەکان (3)
ATF22V10C-15JI - 15ns 10-Macrocell EE PLD | Microchip
The Microchip Technology ATF22V10C-15JI is a high-performance CMOS electrically erasable programmable logic device with 10 macrocells, a 15 ns propagation delay, and a 28-pin PLCC package. Designed for 5 V systems, it combines reusable Flash-memory configuration with 500-gate-equivalent logic capacity, making it suitable for control, decoding, interface, and fixed-protocol logic. The ATF22V10C family also offers performance grades down to 5 ns and typical power dissipation as low as 10 uA. An electrically erasable programmable logic device, or EEPLD, is a semiconductor that stores its logic configuration in nonvolatile memory. It occupies the programmable-logic-device and logic-IC hierarchy while providing an alternative to a mask-programmed PAL, GAL, or discrete gate-array implementation. Because the configuration can be electrically erased and reprogrammed, the ATF22V10C supports design revisions, field updates, and simplified logic customization without changing the PCB. The ATF22V10C-15JI includes a latch feature that holds inputs at their previous logic states, a useful behavior for registered control paths and systems requiring state retention. Its 10 macrocells implement sum-of-products logic and programmable I/O functions, while the 15 ns speed grade targets moderate-speed control logic. The family’s electrically erasable Flash technology permits nonvolatile configuration and eliminates the fuse-programming constraints associated with older one-time-programmable devices. Typical uses include peripheral address decoding, control-signal generation, latch-based sequencing, glue logic for processors and FPGAs, and compact interface adapters. Its 28-pin PLCC package also makes it appropriate for legacy industrial equipment and test systems where socketed or surface-mount PLCC hardware is already standardized. Designers should preserve the JEDEC-compatible pin arrangement and confirm the original fuse map before substituting it in an existing design. The primary design consideration is compatibility. The ATF22V10C-15JI operates from a nominal 5 V supply, and the manufacturer specifies 5 V ±10% for military and industrial temperature ranges and 5 V ±5% for commercial ranges. Verify temperature grade, supply tolerance, unused pins, and macrocell assignments against the manufacturer datasheet before releasing a replacement or new PCB. This page combines the manufacturer specifications, verified sourcing information, drop-in comparison candidates, and practical migration guidance for engineers evaluating the ATF22V10C-15JI in legacy programmable-logic designs.
GTL2014PW,112 - 4-Bit LVTTL to GTL Transceiver | NXP
The NXP Semiconductors GTL2014PW,112 is a 4-bit bidirectional LVTTL-to-GTL translating transceiver with a propagation-delay optimized mixed-signal design, 3.3 V LVTTL side interfacing to GTL-/GTL/GTL+ bus reference levels, housed in a 14-pin TSSOP (SOT402-1) package. A voltage level translator is a mixed-signal interface IC that allows logic blocks operating at different supply domains to exchange signals safely. Within the signal-chain hierarchy, translators sit between bus transceivers and buffers, forming part of the broader family of interface and logic ICs. GTL (Gunning Transceiver Logic) is a low-swing open-drain bus standard historically used for processor front-side buses and memory interfaces, where the bus voltage is defined relative to a reference voltage (Vref) such as 1.0 V or lower, while the system side typically runs at 3.3 V LVTTL. Key features of the GTL2014 include its 4-bit bidirectional architecture with a single direction (DIR) control pin, allowing the device to act either as a GTL-to-LVTTL sampling receiver or as an LVTTL-to-GTL interface. The GTL-side threshold tracks the Vref pin, which supports GTL-, GTL, and GTL+ bus variants; according to the NXP datasheet, Vref tracks linearly down to 0.5 V for low-voltage CPU applications, a wider usable tracking range than the related GTL2005. Technically, the device is fabricated in a BiCMOS process, combining bipolar drive capability for the low-impedance GTL bus with CMOS low static power on the LVTTL side. The GTL side uses open-drain outputs pulled up to VTT through bus termination resistors, so the translator dissipates termination power in the resistors rather than in the IC. Input/output capacitance on the B port is on the order of 3.4 pF to 4.3 pF per the datasheet, keeping bus loading low. Typical applications include processor-to-memory bus translation in legacy server and networking platforms, backplane control lines bridging a 3.3 V microcontroller or FPGA to a GTL signaling bus, and mixed-voltage board-level upgrades of GTL-based systems. The four-bit width matches byte-strobe or chip-select groupings. A key design consideration is that the GTL2014 is pin-to-pin backward compatible with the GTL2005, but the A-port and B-port labels are interchanged; propagation delays are slightly longer in exchange for better Vref linearity below 0.8 V, so drop-in migration from GTL2005 requires re-checking timing margin. This page synthesizes verified distributor listings, the NXP product page, drop-in compatibility analysis, and practical design notes not found in the manufacturer datasheet.
SN74LS245M - 3-State Octal Bus Transceiver | Texas Instruments
Texas Instruments SN74LS245M is an octal bus transceiver with 3-state outputs, eight data lines per direction, and a 20-pin dual in-line package. It is designed for asynchronous, two-way communication between data buses, with separate direction and enable controls for bus isolation and drive management. The SN74LS245M belongs to the SNx4LS245 family of octal bus transceivers. An octal bus transceiver is a bidirectional logic interface that connects two buses through eight parallel data lines. It can transmit data from bus A to bus B or from bus B to bus A, depending on the direction-control input. The 3-state outputs place each data line into a high-impedance state when the device is disabled, allowing multiple bus drivers to share the same physical bus without creating active drive conflicts. Key features include eight 3-state data channels, bidirectional bus operation, a dedicated enable input for bus isolation, and a direction input for selecting the transmission path. The manufacturer identifies the family for asynchronous two-way bus communication, while its control-function implementation reduces external timing requirements. The 20-pin package provides a conventional through-hole footprint suitable for legacy computer, industrial-control, instrumentation, and embedded-system boards. The SN74LS245 architecture separates the A-side and B-side data paths while using common direction and enable controls for all eight channels. When enable is asserted, the direction input determines which bus actively drives the data lines. When enable is deasserted, the output drivers enter the high-impedance state. This arrangement supports controlled bus sharing, CPU-to-peripheral data paths, bidirectional peripheral interfaces, and temporary isolation of a bus segment during system configuration or test. Typical applications include bidirectional data-bus buffering in computer systems, programmable peripheral interfaces, memory-bus isolation, test and measurement equipment, and industrial control systems. In each case, the transceiver can reduce contention by disabling one bus segment when another driver must control the shared line. The device is particularly useful in designs that retain 5 V TTL-style logic and require eight parallel lines rather than a serial transceiver. When laying out a board, place the SN74LS245M close to the connector or bus driver it isolates, route each data line as a short matched trace, and keep ground return paths continuous. Confirm the DIR and enable levels during reset so that no two enabled drivers contend on the same bus. Follow the manufacturer datasheet pin description table when assigning tracks because the package pin arrangement alternates A-side and B-side data signals. This page consolidates the device function, bus-control behavior, package details, verified sourcing links, practical application guidance, and qualified same-footprint alternatives into an engineering reference for legacy TTL and LS-series designs.