بەرهەمەکان (2,800+)

VN808CM - Octal High-Side Driver, VIPower M0-3, PowerSO-36 | STMicroelectronics
VN808CM

VN808CM - Octal High-Side Driver, VIPower M0-3, PowerSO-36 | STMicroelectronics

The STMicroelectronics VN808CM-E and VN808CM-32-E are monolithic octal high-side power switches built on ST's VIPower M0-3 technology, housed in a 36-pin PowerSO package with an exposed bottom thermal pad. Each device integrates eight independent N-channel MOSFET high-side drivers rated at 700 mA per channel (1 A on the VN808CM-32-E variant), with CMOS-compatible 3.3 V logic inputs that interface directly to microcontrollers without level shifters. Built-in protection includes active current limitation, junction over-temperature shutdown, case over-temperature shutdown (for thermal independence between channels), shorted-load protection, undervoltage shutdown, and loss-of-ground protection, with automatic restart after fault clearance. The very low standby current makes the device well suited to permanently wired automotive and industrial loads where quiescent drain must be minimized. A high-side driver is a type of power switch that sits between the supply rail and the load, controlling current flow by switching the positive (high) side rather than the low side. In the broader semiconductor taxonomy, a high-side driver belongs to the smart power switch / power management IC family, sitting alongside low-side drivers, H-bridges, and solid-state relays. Eight-channel parts like the VN808CM are particularly valued where PCB real estate is tight and many discrete FETs would otherwise occupy valuable board area. Key features of the VN808CM include 700 mA continuous output current per channel (1 A on the -32-E variant), CMOS-compatible input thresholds, very low standby current, compliance with IEC 61000-4-4/4-5 EMC immunity standards, and full RoHS compliance. Each channel is independently protected, so a fault on one output does not disable the other seven. The exposed bottom pad of the PowerSO-36 package keeps junction-to-ambient thermal resistance low enough to dissipate multi-channel loads from a single exposed-pad footprint. The VIPower M0-3 process combines a vertical DMOS output stage with CMOS logic on the same die, allowing the protection circuitry to act on the same silicon that carries the load current. This co-integration is what enables the very fast shorted-load and over-temperature response that discrete FET designs cannot match without external comparators and sense resistors. Typical applications include automotive body controllers (driving lamps, solenoids, and relays), PLC digital outputs, industrial actuator drivers, and any multi-load system where eight ground-referenced loads must be switched independently from logic-level signals. The device is also widely deployed in HVAC control boards and building automation panels. When designing with this part, ensure that the exposed bottom pad is soldered to a sufficiently large copper pour (typically 1 square inch or more) to keep junction temperature within rated limits when multiple channels are simultaneously driving heavy loads. Per-channel thermal independence means the case-temperature sensor trips only on overall package heating, not per-channel, so system-level derating should account for worst-case cumulative dissipation. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical PCB thermal notes for the VN808CM and VN808CM-E/-32-E variants - engineering context not consolidated on any single distributor page.

RFQ پەیوەندی
VND5050K-E - 41A High-Side Driver, 36V | STMicroelectronics
VND5050K-E

VND5050K-E - 41A High-Side Driver, 36V | STMicroelectronics

The STMicroelectronics VND5050K-E is a monolithic high-side driver with a 41A current limit and 36V operating voltage, housed in a PowerSSO-12 package. It is designed for driving resistive, inductive, and capacitive loads in automotive and industrial applications, featuring built-in protection against overcurrent, overtemperature, and short-circuit conditions. A high-side driver is a power management IC that connects a load to the positive supply rail, providing switching and protection functions. It integrates a power MOSFET, control logic, and diagnostic circuitry in a single package, simplifying system design and enhancing reliability. In the hierarchy of power management, a high-side driver falls under power switches, which are part of discrete power semiconductors and power management ICs. Key features of the VND5050K-E include a very low ON-state resistance of 50 mOhm, a wide operating voltage range from 4.5V to 36V, and a standby current of only 0.5 uA. It provides analog current sense output for load diagnostics and has a dedicated status pin for fault reporting. The device is AEC-Q100 qualified, making it suitable for automotive environments. The VND5050K-E uses STMicroelectronics' VIPower M0-5 technology, which integrates a vertical P-channel MOSFET with CMOS control logic. This architecture enables high current handling with low power dissipation and fast switching. The PowerSSO-12 package offers excellent thermal performance with a thermal resistance of 40 C/W, allowing operation at high ambient temperatures without external heatsinking in many applications. Typical applications include automotive lighting control, DC motor driving, solenoid actuation, and general-purpose load switching in industrial control systems. The device's robust protection features make it ideal for harsh environments where load faults are common. When designing with the VND5050K-E, ensure adequate PCB copper area for heat dissipation and place the sense resistor close to the device for accurate current sensing. The input pin is compatible with both 3.3V and 5V logic levels, simplifying microcontroller interfacing.

RFQ پەیوەندی
VND5160AJTR-E - 3.8A Dual High-Side Driver PowerSSO-12 | STMicro
VND5160AJTR-E

VND5160AJTR-E - 3.8A Dual High-Side Driver PowerSSO-12 | STMicro

The STMicroelectronics VND5160AJTR-E is a double-channel high-side driver with analog current sense, built on ST's VIPower M0-5 technology and housed in a 12-pin PowerSSO package with exposed pad. It is engineered for automotive resistive or inductive loads and is rated for 3.8 A continuous output per channel (up to 5 A in pulsed mode) with a typical on-state resistance of 160 mOhm per channel from a nominal 13 V supply. The integrated analog current sense delivers a proportional feedback signal for ground-referenced load monitoring and short-circuit diagnostics. What is a high-side driver? A high-side MOSFET switch is a type of power switch that sits between the supply rail and the load, allowing the load to be turned on/off or modulated by an MCU logic-level signal while keeping the load's low-side terminal referenced to ground. In the hierarchy of power management ICs, the VND5160AJTR-E belongs to the "smart high-side switch / driver IC" family - more capable than a discrete MOSFET because it integrates protection, current sensing, and self-diagnostics in one package. Key features include very low quiescent current with full protection against battery transient spikes per ISO7637, open-load detection in both on and off states, active VCC clamp for low-energy transient protection, over-temperature shutdown, and a status flag output (STAT_DIS pin) for fault reporting. The analog current sense (CS pin) delivers a mirrored current proportional to the load current, allowing precise load diagnostics and predictive maintenance. The VIPower M0-5 vertical process integrates a robust N-channel power MOSFET with dedicated analog and digital control blocks on a single die, delivering automotive-grade ruggedness in a tiny footprint. Active clamp and demagnetization handling for inductive loads means relays, solenoids, and small motors can be driven directly without external freewheeling diodes. Typical applications include automotive body electronics (door lock, lighting, seat control), industrial PLC outputs, relay/solenoid replacement, and resistive load switching where diagnostic feedback is required. The wide operating voltage range (4.5 V to 36 V) covers both 12 V automotive and 24 V truck systems. When designing with this part, ensure the CS pin filter network (R-C values) matches your desired current sense bandwidth and diagnostic timing. The exposed pad (PowerSSO EP) must be soldered to a sufficient copper pour for thermal dissipation; expect roughly 31 C/W junction-to-ambient thermal resistance on a 2 cm² 2-oz copper area. This page synthesizes distributor pricing, drop-in same-package alternatives, application examples, and PCB layout notes not available on a single manufacturer product page.

RFQ پەیوەندی
VND5160AJTRE - Dual 41V 3.8A High-Side Driver | STMicroelectronics
VND5160AJTRE

VND5160AJTRE - Dual 41V 3.8A High-Side Driver | STMicroelectronics

The STMicroelectronics VND5160AJTRE is a monolithic dual-channel high-side driver built on ST's VIPower M0-3 technology, delivering up to 3.8 A continuous output current per channel in a 12-pin PowerSSO-12 (PowerSSO-12L) surface-mount package. Designed for automotive resistive and inductive loads, each channel integrates a 60 mΩ R<sub>DS(on)</sub> N-channel MOSFET power stage, an active V<sub>CC</sub> clamp for ISO 7637 transient compatibility, and an analog current-sense output that delivers a current proportional to the load current. What is a high-side driver? A high-side driver is a type of power switch that sits between the positive supply rail and the load, allowing the MCU ground-referenced logic to switch the positive rail to a grounded load such as a bulb, solenoid, or DC motor. In the broader semiconductor taxonomy, the high-side driver sits within smart power ICs, which sit within power management ICs. Compared to a discrete MOSFET plus gate driver, an integrated smart high-side switch saves board area, adds load-current diagnostics, and provides on-chip protection against short circuits, open loads, and thermal overload. Key features of the VND5160AJTRE include 41 V load-dump-tolerant V<sub>CC</sub> rating, 3.8 A continuous current per channel (limited thermally), 60 mΩ R<sub>DS(on)</sub> at 25 °C, very low quiescent current for standby operation, fast demagnetization of inductive loads, and a CS_DIS pin for multiplexing current sense. The analog current-sense output allows the host MCU to detect partial loads, shorts to ground, and open-circuit conditions without additional shunt resistors. The VIPower M0-3 process combines a vertical N-channel DMOS output stage with bipolar and CMOS analog/mixed-signal circuitry on the same die. This monolithic integration reduces parasitic inductance, simplifies PCB layout, and provides intelligent protection features including thermal shutdown, current limitation, and load-dump transient clamping per ISO 7637. Typical applications include automotive body electronics such as LED lighting drivers, HVAC relays, door-lock actuators, seat heaters, and small DC motor control. The wide V<sub>CC</sub> tolerance and analog current sense make it well suited for replacing electromechanical relays with solid-state switching in body control modules. When designing with this part, place the VND5160CC charge-pump capacitor and bootstrap components as close to the IC as possible, ensure adequate copper heat sinking for thermal dissipation, and use the VND5160's analog current sense with an external sense resistor to monitor load health. The exposed pad must be soldered to a sufficiently large copper pour for thermal dissipation; undersized PCB copper will trigger thermal shutdown at lower than expected currents. This page synthesizes distributor pricing, drop-in PowerSSO-12 alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides, including cross-references to second-source parts vetted for the same PCB footprint.

RFQ پەیوەندی
VND5160J-E - 16A High-Side Driver | STMicroelectronics | Automotive
VND5160J-E

VND5160J-E - 16A High-Side Driver | STMicroelectronics | Automotive

The VND5160J-E is a monolithic high-side driver manufactured by STMicroelectronics, designed to drive resistive, inductive, and capacitive loads in automotive and industrial applications. It integrates a vertical MOSFET power stage with a full set of protection and diagnostic features in a compact PowerSSO-12 package. The device delivers a continuous output current of up to 16A (with proper thermal management) and operates from a supply voltage range of 4.5V to 36V, making it suitable for 12V and 24V automotive electrical systems. A high-side driver is a power management IC that connects a load to the positive supply rail, providing switching, protection, and diagnostic functions. It is a key component in automotive body control modules, where it replaces discrete relays and fuses with a more reliable, semiconductor-based solution. High-side drivers are part of the broader power management IC family, which includes low-side drivers, half-bridge drivers, and full-bridge drivers, all essential for controlling actuators, lamps, and motors in modern vehicles. Key features of the VND5160J-E include an output current limit of 16A, a low ON-state resistance (RDS(on)) of 60 mOhm typical at 25°C, and a standby current of only 5 µA. The device provides comprehensive protection against overcurrent, overtemperature, and short-circuit conditions, with an open-load detection feature for both ON and OFF states. It also includes a status output that reports fault conditions to the microcontroller, enabling real-time diagnostics. The PowerSSO-12 package offers excellent thermal performance with a thermal resistance of 40°C/W, allowing high-current operation without external heatsinking in many applications. The VND5160J-E is built using STMicroelectronics' VIPower M0-5 technology, which combines a vertical MOSFET with CMOS control logic on a single chip. This integration reduces component count and improves reliability compared to discrete solutions. The device is AEC-Q100 qualified, ensuring it meets the stringent quality and reliability requirements of the automotive industry. Its wide operating temperature range of -40°C to +150°C makes it suitable for under-hood and engine compartment applications. Typical applications include automotive body control modules for driving exterior and interior lighting, resistive heaters, and small DC motors. It is also used in industrial automation for controlling solenoids, valves, and actuators. The device's low standby current and robust protection features make it ideal for always-on applications in battery-powered systems. When designing with the VND5160J-E, ensure adequate PCB copper area for heat dissipation, especially when driving currents above 10A. The status pin should be connected to a microcontroller input with a pull-up resistor to enable fault detection. Proper decoupling capacitors on the supply and output pins are essential to minimize voltage transients during switching.

USD $1.65 پەیوەندی
VND5E160AJTR-E - 7A High-Side Driver, VIPower M0-5, PowerSSO-12 | ST
VND5E160AJTR-E

VND5E160AJTR-E - 7A High-Side Driver, VIPower M0-5, PowerSSO-12 | ST

The STMicroelectronics VND5E160AJTR-E is a single-channel high-side power switch / driver manufactured in ST's proprietary VIPower M0-5 technology and housed in the compact PowerSSO-12 surface-mount package. It is rated for 7 A continuous output current and is designed to drive 12 V automotive grounded loads while providing protection, diagnostics, and a 3 V / 5 V CMOS-compatible logic interface to any microcontroller. What is a high-side driver? A high-side driver is a type of smart power switch that sits between the battery/positive supply rail and the load, replacing discrete MOSFETs, fuses, and relay combinations. It belongs to the broader family of power switches / intelligent power switches (IPS) within the power management IC category, providing load protection, current sensing, and fault feedback to the microcontroller. Key features include 7 A continuous drain current (I_Load), 28 V operating supply range (V_CC), an integrated analog current-sense output (I_SENSE pin) proportional to load current, and built-in protections for load-dump, reverse-battery, over-temperature, short-circuit, and over-current conditions. The 3 V / 5 V CMOS-compatible input enables direct connection to modern microcontrollers without level shifters, simplifying the BOM in body and chassis control modules. The VIPower M0-5 process combines a vertical N-channel power MOSFET with analog and digital control blocks on the same die, enabling accurate current sensing (typically K_ILIS sense ratio) and robust switching. An exposed-pad PowerSSO-12 layout provides a low thermal resistance path (~5 °C/W junction-to-tab) for dissipating the I²R losses of 12 V automotive switching. Typical applications include automotive body modules for resistive and inductive loads such as lamps, LED arrays, motors, solenoids, and heaters, as well as industrial 24 V systems where reverse-battery and load-dump protection are required. The analog current-sense output also supports predictive maintenance by enabling MCU-side load-current monitoring. When designing with this part, place it as close as possible to the connector it is switching, and keep the protected load loop area minimal to reduce EMI from the 12 V bus. A small TVS across V_CC and an RC snubber on the output may be required for highly inductive loads such as solenoids or DC motors. This page synthesizes distributor pricing, same-brand drop-in alternatives such as the VND5E160JTR-E and VND5E160AJ-E, and practical design notes not consolidated on a single manufacturer or distributor page.

RFQ پەیوەندی
VND7004AYTR - 4A High-Side Driver with MultiSense | STMicroelectronics
VND7004AYTR

VND7004AYTR - 4A High-Side Driver with MultiSense | STMicroelectronics

The VND7004AYTR is a monolithic double channel high-side driver manufactured by STMicroelectronics using the proprietary VIPower M0-7 technology and housed in a PowerSSO-36 package. It is designed to drive 12 V automotive grounded loads through a 3 V and 5 V CMOS-compatible interface, providing protection and diagnostics. The device integrates advanced protective functions such as load current limitation, overload latch-off, thermal shutdown, and loss of ground protection, making it a robust solution for harsh automotive and industrial environments. A high-side driver is a type of power switch that connects a load to the positive supply rail, providing protection and diagnostic functions. It is a key component in automotive and industrial systems where loads such as lamps, relays, solenoids, and motors must be controlled safely. High-side drivers are part of the broader category of power management ICs, which manage the distribution and control of electrical power in electronic systems. The VND7004AYTR integrates advanced protection features including load current limitation, overload protection, thermal shutdown, and loss of ground protection, making it a robust solution for harsh environments. Key features of the VND7004AYTR include a 3V to 5V logic-level input compatible with microcontrollers, a standby current of only 0.5 µA (typ) to preserve battery life, and a fast demagnetization of inductive loads to reduce switching losses. The device also provides a status output for diagnostic feedback, enabling real-time monitoring of load conditions. Its low ON-state resistance and high current capability make it suitable for driving high-power loads without external heatsinks in many applications. The VND7004AYTR is built using STMicroelectronics' VIPower M0-7 technology, which integrates the power MOSFET with control and protection circuitry on a single chip. This monolithic approach reduces component count, improves reliability, and simplifies PCB layout. The device is fully protected against short circuits, overcurrent, and overtemperature, ensuring safe operation under fault conditions. Its fast switching performance and low quiescent current make it ideal for battery-operated and energy-efficient systems. Typical applications include automotive body control modules, lighting systems, industrial PLCs, and general-purpose power switching. In automotive applications, the VND7004AYTR can drive headlamps, wiper motors, and heating elements, while in industrial settings it can control solenoids, valves, and DC motors. The device's wide supply voltage range and robust protection make it a versatile choice for both 12V and 24V systems. When designing with the VND7004AYTR, ensure adequate PCB copper area for thermal dissipation, especially when driving continuous high currents. The exposed pad of the PowerSSO-36 package should be soldered to a large ground plane to minimize thermal resistance. Additionally, place a 100 nF ceramic capacitor close to the VCC pin to suppress voltage transients and ensure stable operation.

RFQ پەیوەندی
VND7040AJTR - 40A High-Side Driver | STMicroelectronics | Automotive
VND7040AJTR

VND7040AJTR - 40A High-Side Driver | STMicroelectronics | Automotive

The VND7040AJTR is a double-channel high-side driver from STMicroelectronics, designed for automotive and industrial applications requiring robust power switching. It features a maximum output current of 40A, an operating voltage range of 4V to 28V, and is housed in a PowerSSO-16 package. The device integrates advanced protection features including overvoltage, undervoltage, overcurrent, and thermal shutdown, ensuring reliable operation in harsh environments. A high-side driver is a type of power switch that connects a load to the positive supply rail. It is commonly used in automotive systems to control lamps, motors, and solenoids, where the load must be switched on the high side for safety and diagnostic reasons. High-side drivers are part of the broader category of power management ICs, which manage and distribute power within electronic systems. Key features of the VND7040AJTR include a low quiescent current of 50 µA, a standby current of 5 µA, and a fast switching speed with rise and fall times of 10 µs and 15 µs, respectively. The device also provides a diagnostic output for fault detection, making it suitable for smart power distribution in automotive body control modules. The VND7040AJTR uses a proprietary VIPower M0-5 technology, which integrates the power MOSFET and control circuitry on a single chip. This technology ensures high efficiency and low power dissipation, with a typical on-resistance of 40 mΩ at 25°C. The device is AEC-Q100 qualified, meeting the stringent reliability standards for automotive electronics. Typical applications include automotive lighting control, DC motor driving, and power distribution in body control modules. The device's wide operating voltage range and robust protection features make it ideal for 12V and 24V automotive systems, as well as industrial PLCs and factory automation. When designing with the VND7040AJTR, it is essential to consider thermal management. The PowerSSO-16 package has a thermal resistance of 40°C/W, so adequate PCB copper area or a heatsink is required for high-current applications. Additionally, proper decoupling capacitors should be placed close to the supply pins to minimize voltage transients.

RFQ پەیوەندی
VND7050AJTR - Dual 70mOhm High-Side Driver | STMicroelectronics
VND7050AJTR

VND7050AJTR - Dual 70mOhm High-Side Driver | STMicroelectronics

The VND7050AJTR is a dual-channel high-side driver from STMicroelectronics, designed for automotive and industrial applications requiring robust power switching. It integrates two 70mOhm (typical) N-channel power MOSFETs with full protection and diagnostic features, housed in a PowerSSO-16 package. The device operates over a wide supply voltage range of 4V to 28V, making it suitable for 12V and 24V systems. Each channel can deliver up to 9A of continuous current, with a maximum current limitation of 14A (typical). The driver features an active-low enable input, open-drain diagnostic output, and built-in protection against overcurrent, overtemperature, and short-circuit conditions. A high-side driver is a power management IC that switches power to a load connected to ground, commonly used in automotive body control modules, industrial PLCs, and lighting systems. It integrates the power MOSFET, protection circuitry, and diagnostic feedback into a single package, simplifying PCB design and improving reliability. High-side drivers are part of the broader power management IC family, which includes low-side drivers, half-bridge drivers, and full-bridge drivers. The VND7050AJTR belongs to the VIPower M0-5 technology family, which is known for its low quiescent current and advanced protection features. Key features of the VND7050AJTR include a very low standby current of 0.5uA (typical) when disabled, which is critical for battery-powered automotive applications. The device also provides a diagnostic output that indicates open-load, short-to-ground, and overtemperature conditions. The PowerSSO-16 package offers excellent thermal performance with a thermal resistance of 40C/W (junction-to-ambient), enabling high-current operation without external heatsinks in many applications. The driver is AEC-Q100 qualified, ensuring reliability in harsh automotive environments. Technically, the VND7050AJTR uses a vertical N-channel power MOSFET architecture with a charge pump to drive the high-side switch. The charge pump allows the device to operate with a low input voltage while maintaining a low on-resistance. The device includes a current sense output that provides a proportional current signal for load monitoring, enabling precise control and diagnostics. The protection circuitry includes overvoltage clamping, reverse battery protection (with external resistor), and thermal shutdown with automatic restart. Typical applications include automotive body control modules for driving exterior lights, interior lighting, and DC motors; industrial PLCs for controlling solenoids and relays; and general-purpose power switching in 12V/24V systems. The VND7050AJTR is also suitable for driving resistive, capacitive, and inductive loads, making it a versatile choice for many power switching applications. When designing with this device, ensure adequate PCB copper area for thermal dissipation, especially when driving high currents. The diagnostic output should be connected to a microcontroller input with a pull-up resistor. For inductive loads, an external freewheeling diode is recommended to clamp voltage spikes during turn-off.

RFQ پەیوەندی
VND7140AJTR - Dual High-Side Driver 8A | STMicroelectronics | Automotive
VND7140AJTR

VND7140AJTR - Dual High-Side Driver 8A | STMicroelectronics | Automotive

The VND7140AJTR is a double channel high-side driver manufactured by STMicroelectronics using the proprietary VIPower M0-7 technology. It is housed in a PowerSSO-16 package and designed to drive 12V automotive grounded loads through a 3V and 5V CMOS-compatible interface. The device delivers up to 8A per channel and integrates advanced protective functions including load current limitation, overload active management by power limitation, and overtemperature shutdown with configurable latch-off. A high-side driver is a power management IC that connects a load to the positive supply rail, providing switching, protection, and diagnostic functions. In automotive systems, high-side drivers are essential for controlling lamps, solenoids, motors, and resistive loads while offering protection against short circuits, overcurrent, and overtemperature conditions. The VND7140AJTR belongs to the family of smart power switches, which combine power MOSFET technology with control and protection circuitry on a single chip. Key features of the VND7140AJTR include a MultiSense analog feedback pin that provides multiplexed analog feedback of load current with high precision proportional current mirror, VCC supply voltage, and TCHIP device temperature. This enables precise diagnostics and monitoring of the load condition. The device also features a FaultRST pin that unlatches the output in case of fault or disables the latch-off functionality, allowing flexible fault management. The PowerSSO-16 package offers excellent thermal performance with an exposed pad for efficient heat dissipation. The VND7140AJTR is designed for automotive applications and is AEC-Q100 qualified, ensuring reliability under harsh operating conditions. The device operates over a wide input voltage range and provides robust protection against load dump, reverse battery, and electrostatic discharge. The MultiSense feedback allows the microcontroller to read the load current, supply voltage, and device temperature, enabling advanced diagnostic and predictive maintenance capabilities. Typical applications include automotive body control modules, lighting control, DC motor control, and resistive load driving. The device is also suitable for industrial applications requiring high-side switching with diagnostic feedback. The VND7140AJTR is available in tape and reel packaging with a standard quantity of 1000 units per reel. When designing with the VND7140AJTR, ensure proper thermal management by connecting the exposed pad to a large copper area on the PCB. The MultiSense pin should be connected to an ADC input of the microcontroller for accurate current and temperature monitoring. The FaultRST pin can be used to implement latch-off or auto-restart fault handling depending on the application requirements.

RFQ پەیوەندی
VND7E050AJTR - Dual 50A High-Side Driver | STMicroelectronics
VND7E050AJTR

VND7E050AJTR - Dual 50A High-Side Driver | STMicroelectronics

The STMicroelectronics VND7E050AJTR is a dual-channel high-side driver (HSD) manufactured with proprietary ST VIPower M0-7 technology, housed in a 16-pin PowerSSO-16 package with an exposed thermal pad. Each channel is rated for 50 A continuous load current and the device targets 12 V automotive grounded loads driven from 3 V / 5 V CMOS-compatible logic. Integrated protections include load current limitation, overload active management by power limitation, and configurable-latch overtemperature shutdown. A high-side driver (HSD) is a power-management switch that sits between the battery rail and the load, controlling current flow by pulling the load up to Vbat. Compared with low-side switches, high-side drivers permit the chassis-grounded load convention used in automobiles, simplify fault detection on a short-to-ground, and allow the load to be turned off safely while the rest of the harness remains live. Within the broader taxonomy, the VND7E050AJTR belongs to the smart-power switch family that subsumes simple MOSFETs, then integrates diagnostics, protection, and a current-sense analog feedback channel to deliver load-current and chip-temperature telemetry to the body-control ECU. Key electrical characteristics include dual 50 A continuous outputs, very low standby current (VND7E050 family typically 5 uA standby), analog current-sense (CS) output with multiplexer for load current / VCC / temperature diagnostics, and a dedicated FaultRST pin to unlatch the output after a fault event. The chip features 3 V and 5 V CMOS-compatible inputs, very low quiescent current draw, and STMicroelectronics' VIPower vertical intelligent power process. Typical use cases include automotive body-domain loads such as LED lighting modules, seat heaters, window lifters, door locks, and small DC motors. The multiplexed current-sense output enables predictive maintenance by detecting bulb-failure or motor-stall events without intrusive shunt resistors. When designing with the VND7E050AJTR, ensure the heatsink area can dissipate worst-case I²R losses (each channel), respect the reverse-battery and load-dump transient ratings of the VIPower M0-7 process, and assign a unique latch-off behavior for the FaultRST pin. Properly routed PowerSSO-16 copper pours are mandatory to maintain junction temperature below 150 °C.

RFQ پەیوەندی
VNH3SP30 - 30A Full-Bridge Motor Driver | STMicroelectronics
VNH3SP30

VNH3SP30 - 30A Full-Bridge Motor Driver | STMicroelectronics

The VNH3SP30 is a fully integrated H-bridge motor driver from STMicroelectronics, designed for a wide range of automotive and industrial applications. It incorporates a dual monolithic high-side driver (HSD) and two low-side switches, providing a complete bridge driver solution in a MultiPowerSO-30 package. The device is capable of driving DC motors with continuous currents up to 30A, making it suitable for high-power actuation systems. A full-bridge motor driver, also known as an H-bridge, is a power electronics circuit that allows a DC motor to be driven in both directions (forward and reverse) by controlling the polarity of the voltage applied across the motor terminals. It consists of four switching elements (typically MOSFETs or IGBTs) arranged in an 'H' configuration. The VNH3SP30 integrates these switches along with protection and diagnostic features, simplifying the design of motor control systems. In the hierarchy of motor control, the H-bridge driver sits between the microcontroller (which generates PWM signals) and the motor itself, translating low-power logic signals into high-current drive capability. Key features of the VNH3SP30 include a wide operating voltage range (5.5V to 36V), a maximum output current of 30A, and a low on-resistance (RDS(on)) of 0.05 ohms per switch, which minimizes power dissipation. The device supports both parallel and PWM control modes, allowing flexible speed and direction control. It also includes built-in protection features such as undervoltage lockout, overcurrent protection, and thermal shutdown, ensuring reliable operation in harsh environments. The VNH3SP30 is built using ST's proprietary VIPower M0 technology, which integrates the power MOSFETs and control logic on a single chip. This monolithic approach reduces parasitic inductance and improves switching performance compared to discrete solutions. The MultiPowerSO-30 package provides excellent thermal performance, with a thermal resistance of 1.5°C/W, enabling the driver to handle high currents without external heatsinks in many applications. Typical applications include automotive systems such as power windows, seat adjusters, and wiper motors, as well as industrial automation, robotics, and electric vehicles. The device's ability to handle 30A makes it ideal for driving large DC motors in actuators, pumps, and conveyor systems. Its automotive-grade qualification (AEC-Q100) ensures reliability in demanding environments. When designing with the VNH3SP30, it is essential to provide adequate bulk capacitance on the power supply to handle the high inrush currents of DC motors. Additionally, proper PCB layout with wide copper traces and thermal vias is critical to dissipate heat effectively. The device's PWM input allows for speed control, but the PWM frequency should be chosen carefully to balance switching losses and motor noise.

RFQ پەیوەندی
VNH3SP30-E - 30A Automotive H-Bridge Motor Driver | STMicroelectronics
VNH3SP30-E

VNH3SP30-E - 30A Automotive H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH3SP30-E is an automotive-grade fully-integrated H-bridge motor driver in a 30-pin MultiPowerSO-30 package, delivering up to 30 A continuous output current from a 5.5 V to 36 V supply. The IC integrates a dual monolithic high-side driver (HSD), two low-side switches, control logic, charge pump, and protective functions into one package, replacing discrete MOSFET bridges plus gate drivers. According to the ST datasheet, the device is targeted at DC motor control in harsh automotive environments. What is an H-bridge motor driver? An H-bridge is a four-switch topology that can drive a brushed DC motor in both directions by reversing the polarity of the applied voltage. Integrated H-bridge ICs combine the four power switches, gate drivers, current sensing, and protection (over-current, over-temperature, under-voltage, cross-conduction prevention) into a single package. This category sits within the broader taxonomy of motor drivers -> motion control ICs -> power management ICs -> semiconductors. The MultiPowerSO-30 package exposes the power die to a top-side thermal pad so heat can be sunk directly to a heatsink or chassis. Key features include 30 A continuous DC output current, 60 A peak transient capability, very low Rds(on) of approximately 9 mOhm per high-side + low-side leg, integrated PWM current control, and built-in diagnostics. The logic inputs accept 5 V CMOS signals and the device supports PWM frequencies up to 10 kHz for speed/torque regulation. The MultiPowerSO-30 package provides a low thermal resistance path enabling high-current operation without external cooling up to the datasheet rating. Typical applications include automotive DC motor control such as window lifts, seat adjusters, sunroof drives, door locks, wiper systems, and small electric vehicle traction. Industrial uses include robotic actuators, conveyor drives, valve positioning, and battery-powered equipment where a compact, fully-protected H-bridge is required. When designing with the VNH3SP30-E, observe the datasheet SOA at high currents - the junction-to-ambient thermal resistance limits continuous current without a heatsink. Use a low-ESR supply bypass close to VCC, and provide a reverse-battery protection diode or P-MOSFET on the supply line because the IC does not include reverse-polarity protection internally. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, organized for engineers evaluating the VNH3SP30-E for automotive or industrial motor-drive designs.

RFQ پەیوەندی
VNH3SP30TR-E - 30A H-Bridge Motor Driver MultiPowerSO-30 | STMicroelectronics
VNH3SP30TR-E

VNH3SP30TR-E - 30A H-Bridge Motor Driver MultiPowerSO-30 | STMicroelectronics

The STMicroelectronics VNH3SP30TR-E is an automotive fully integrated H-bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high-side driver (HSD) and two low-side switches, all housed in a MultiPowerSO-30 package with an exposed thermal pad. It delivers up to 30 A continuous output current per switch with a 5.5 V to 36 V supply range. An H-bridge motor driver is a four-switch power topology (two high-side, two low-side MOSFETs) that allows a DC motor to be driven in both directions from a single supply rail. The H-bridge sits in the broader power management hierarchy as a motor driver, an integrated power IC that combines the logic interface, gate drivers, protection features, and power FETs in one package. By integrating everything monolithically, the H-bridge IC replaces tens of discrete components and simplifies PCB layout for brushed DC and stepper motor control. Key features of the VNH3SP30TR-E include PWM current control, parallel-mode operation for higher current loads, integrated charge pump for high-side gate drive, built-in thermal shutdown, cross-conduction protection, and a current sense output for closed-loop control. The device can drive two high-side switches in parallel or be configured as a full bridge. The MultiPowerSO-30 package provides a low thermal resistance path for dissipating the heat generated by the power FETs at high motor currents. Typical applications include automotive DC motor control (window lifts, seat adjusters, sliding doors, tailgates, mirrors), industrial robotics and small pumps, HVAC damper actuators, and 24 V brushed servo systems. The wide supply range and integrated protection make it well suited for harsh 12 V/24 V automotive electrical environments with load-dump and cranking transients. When designing with this part, derate the output current according to the PCB copper area used as a heatsink and ambient temperature; the MultiPowerSO-30 package relies on the PCB copper pour for thermal dissipation. Add adequate bulk decoupling on the supply rail and route the power ground separately from the logic ground. Consider the VNH2SP30 for lower-current applications or the VNH5019 for higher-current needs. This page synthesizes verified distributor pricing, drop-in same-package alternatives, application notes, and design guidance not aggregated on the STMicroelectronics datasheet alone, providing engineers with a faster decision-making reference.

RFQ پەیوەندی
VNH5019 - 30A Automotive H-Bridge Motor Driver | STMicroelectronics
VNH5019

VNH5019 - 30A Automotive H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH5019 is a fully integrated automotive-grade H-bridge motor driver designed for high-current DC motor control. It integrates a dual monolithic high-side driver and two low-side switches using ST's proprietary VIPower M0 technology, which combines a true Power MOSFET with an intelligent signal/protection circuit on the same die. The device is assembled in a MultiPowerSO-30 package with electrically isolated lead-frames, enabling efficient thermal management and high-current operation. An H-bridge motor driver is a power management IC that allows a DC motor to be driven in both directions (forward and reverse) by controlling the polarity of the voltage applied across the motor terminals. It sits between a microcontroller and the motor, translating low-power logic signals into high-current switching actions. The VNH5019 belongs to the broader category of motor drivers, which are essential in robotics, automotive, and industrial automation systems where precise speed and direction control are required. Key features of the VNH5019 include a wide operating voltage range of 5.5V to 24V, a continuous output current of 12A with a peak capability of 30A, and an ultra-low on-resistance of 18mOhm per switch. The device supports PWM frequencies up to 20kHz (ultrasonic), enabling silent motor operation. It also provides a current sense output that delivers an analog voltage proportional to the motor current, facilitating closed-loop control and overcurrent monitoring. The VNH5019 integrates comprehensive protection features, including reverse-voltage protection, over-voltage protection, under-voltage lockout, overcurrent protection, and thermal shutdown. These protections ensure robust operation in harsh automotive and industrial environments. The device operates with logic levels from 2.5V to 5V, making it compatible with both 3.3V and 5V microcontrollers. The MultiPowerSO-30 package provides excellent thermal performance, with a junction-to-ambient thermal resistance of [DATA_NEEDED: thermal resistance] C/W, allowing continuous operation at high currents with appropriate PCB copper area. Typical applications include automotive power windows, seat adjusters, and wiper motors, as well as robotics, automated guided vehicles (AGVs), and industrial actuators. The VNH5019 is also widely used in educational robotics platforms and hobbyist motor driver carriers, such as those from Pololu. Its combination of high current capability, integrated protection, and ease of use makes it a preferred choice for designers requiring a reliable, compact H-bridge solution. When designing with the VNH5019, ensure adequate PCB copper area for thermal dissipation, especially when operating at continuous currents above 6A. The current sense output should be connected to an analog-to-digital converter (ADC) input for accurate motor current monitoring. Additionally, proper decoupling capacitors (e.g., 100nF ceramic and 10uF electrolytic) should be placed close to the VCC and GND pins to suppress voltage transients during PWM switching.

RFQ پەیوەندی
VNH5050A-E - 50A Automotive H-Bridge Driver | STMicroelectronics
VNH5050A-E

VNH5050A-E - 50A Automotive H-Bridge Driver | STMicroelectronics

The STMicroelectronics VNH5050A-E is a fully integrated H-bridge motor driver designed for high-current automotive and industrial applications. It delivers a continuous output current of 50 A and a peak current of 70 A, operating from a supply voltage range of 5.5 V to 18 V. The device is housed in a 12-pin MultiPowerSO-30 package with an exposed pad for enhanced thermal performance. An H-bridge motor driver is a power integrated circuit that controls the direction and speed of a DC motor by selectively switching four transistors in an H-shaped configuration. It is a type of motor driver IC, which falls under the broader category of power management ICs. The VNH5050A-E integrates the power stage, gate drivers, and protection circuitry in a single package, simplifying PCB design and reducing component count. Key features include a low ON-resistance of 20 mOhm per switch, which minimizes power dissipation and improves efficiency. The device provides a 5 V logic supply output for external circuitry, and includes a current sense output proportional to the motor current, enabling closed-loop control. It also features a diagnostic output for fault reporting, and a PWM input for speed control up to 20 kHz. The VNH5050A-E uses STMicroelectronics' VIPower M0 technology, which integrates a double-diffused MOS (DMOS) power stage with CMOS control logic. This architecture provides robust switching performance and high reliability under harsh automotive conditions. The device includes comprehensive protection features such as undervoltage lockout, overvoltage clamp, thermal shutdown, and load current limitation. Typical applications include automotive power windows, sunroofs, seat adjusters, and DC motor control in industrial automation. The high current capability and wide supply range make it suitable for driving brushed DC motors in body control modules and actuator systems. When designing with this device, ensure adequate PCB copper area for heat dissipation, as the thermal resistance (junction-to-ambient) is 35 C/W. The exposed pad must be soldered to a large copper pour to maintain junction temperature below the maximum rating of 150 C.

RFQ پەیوەندی
VNH5180A-E - 41A Automotive H-Bridge Motor Driver | STMicroelectronics
VNH5180A-E

VNH5180A-E - 41A Automotive H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH5180A-E is a fully integrated H-bridge motor driver designed for automotive and industrial DC motor control applications. It delivers a continuous output current of up to 41A and operates from a supply voltage range of 5.5V to 18V, making it suitable for high-power brushed DC motors, actuators, and power steering systems. The device is housed in a 16-pin PowerSSO-36 package with an exposed thermal pad, enabling efficient heat dissipation in compact designs. An H-bridge motor driver is a power management IC that controls the direction and speed of a DC motor by selectively switching four transistors in an H configuration. It allows bidirectional current flow through the motor, enabling forward, reverse, and braking operations. The VNH5180A-E integrates the power stage, gate drivers, and protection circuitry into a single package, simplifying PCB design and reducing component count compared to discrete implementations. Key features include a low on-resistance of 20 mOhm per switch, which minimizes power losses and heat generation at high currents. The device provides a PWM frequency range up to 20 kHz, allowing precise speed control. It includes comprehensive protection features such as undervoltage lockout, overvoltage clamp, thermal shutdown, and load current limitation. The VNH5180A-E also features a diagnostic output that reports fault conditions, enhancing system reliability. The VNH5180A-E utilizes a proprietary VIPower M0-5 technology, which integrates the power MOSFETs and control logic on a single die. This architecture ensures fast switching and robust operation under harsh automotive conditions. The device is AEC-Q100 qualified, meeting the stringent reliability requirements for automotive applications. Its 16-pin PowerSSO-36 package provides excellent thermal performance with a junction-to-ambient thermal resistance of 30 C/W, allowing operation at high ambient temperatures with appropriate PCB copper area. Typical applications include automotive power windows, seat adjusters, wiper motors, and industrial automation systems. The device's high current capability and robust protection make it ideal for driving large brushed DC motors in electric power steering (EPS) and engine cooling fans. In automotive body control modules, the VNH5180A-E simplifies motor control by integrating all necessary functions, reducing board space and improving reliability. When designing with the VNH5180A-E, ensure adequate PCB copper area for heat dissipation, especially at continuous currents above 20A. The PWM input should be driven with a proper dead-time to prevent shoot-through. The diagnostic output can be monitored by a microcontroller to detect faults and implement safe shutdown procedures.

RFQ پەیوەندی
VNH7040AYTR - 35A H-Bridge Motor Driver | STMicroelectronics
VNH7040AYTR

VNH7040AYTR - 35A H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH7040AYTR is an automotive-grade fully integrated H-bridge motor driver delivering up to 35 A continuous output current, housed in a 36-pin PowerSSO package with exposed thermal pad for surface-mount assembly. It operates across a 4 V to 28 V supply range with a nominal 13 V rail, integrates a dual monolithic high-side driver and two low-side switches built on ST's proprietary VIPower M0 technology, and combines a true Power MOSFET with intelligent signal/power stages on a single die. What is an H-bridge motor driver? An H-bridge motor driver is a power-integrated circuit that uses four switching elements arranged in an H configuration to drive a brushed DC motor bidirectionally from a single supply rail. It sits in the motor-control signal chain between a low-power MCU (logic-level PWM/direction commands) and a brushed DC or stepper motor, handling the high-current switching that the MCU cannot do directly. Within the broader taxonomy: H-bridge driver -> motor driver -> power management IC -> semiconductor. The VNH7040AY adds diagnostic, current-sense and protection features that a discrete MOSFET H-bridge cannot match in the same footprint. Key features include 35 A continuous output current, integrated current sensing with analog feedback, PWM input up to 20 kHz, built-in thermal shutdown, undervoltage and overvoltage protection, cross-conduction prevention (dead-time management), and an operating temperature window of -40 C to +150 C junction. AEC-Q100 qualification makes it suitable for automotive under-hood environments. The PowerSSO-36 package exposes a thermal pad on its bottom surface, achieving a junction-to-case thermal resistance typically below 1 C/W and enabling PCB-direct heat dissipation. The VIPower M0 architecture allows on-die integration of a vertical DMOS power stage and CMOS/BCD signal logic. This co-integration reduces parasitic inductance, dead time, and bill-of-material count versus a discrete H-bridge using four MOSFETs plus a gate driver IC, while still delivering current sensing through the integrated sense-FET topology. Typical applications include automotive brushed DC motor control (window lift, sliding doors, seat adjustment, sunroof drives, fuel pumps, throttle-by-wire backup), industrial 24 V brushed servo drives, AGV/robot traction wheels, and battery-powered e-mobility traction motors in the 5 A to 30 A range. When designing with this device, observe PCB layout guidelines from ST application notes: keep the power ground return path short, place a 100 nF + bulk capacitor directly on the motor supply pin, and ensure the exposed pad is soldered to at least 200 mm squared of copper for thermal performance. This page synthesizes distributor pricing from DigiKey/Mouser/Arrow, AEC-Q100 qualified drop-in alternatives, and application notes that the manufacturer datasheet does not consolidate in a single location.

RFQ پەیوەندی
VNH7070ASTR - 15A Automotive H-Bridge Motor Driver | STMicroelectronics
VNH7070ASTR

VNH7070ASTR - 15A Automotive H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH7070ASTR is a fully integrated H-bridge motor driver delivering up to 15 A continuous output current, operating from a 4 V to 28 V supply range in a 16-pin SO (Multiwatt derivative) package. It uses ST's proprietary VIPower M0-7 technology to integrate a true Power MOSFET half-bridge and intelligent signal/protection circuitry on the same die, supporting PWM control up to 20 kHz for automotive DC motor loads. An H-bridge motor driver is a power integrated circuit that controls the direction and speed of a DC motor by selectively activating four switches in an H-shaped bridge configuration. The architecture sits within the motor driver hierarchy, itself a sub-category of power management ICs. The VNH7070ASTR integrates control logic, gate drivers, and power MOSFETs into a single package, eliminating the need for discrete FET bridges and reducing PCB area, BOM count, and design complexity. Key features include a low ON-state resistance of 40 mOhm per switch (typical), which minimizes conduction losses and improves thermal performance at high current. The device provides an analog current sense output (CS) delivering a proportional voltage for closed-loop torque control and stall detection, and a diagnostic feedback pin (DIAG/SEL0) reporting overcurrent, overtemperature, and open-load fault conditions. PWM inputs INA and INB support forward, reverse, brake-low, brake-high, and high-impedance states for full four-quadrant motor control. Internally, the VNH7070ASTR combines a dual monolithic high-side driver with two low-side switches assembled in SO-16N package on electrically isolated lead-frames. Protection features include undervoltage lockout, overvoltage clamping (Vclamp), thermal shutdown with automatic restart, cross-conduction protection, and short-to-ground/short-to-VBAT detection. The exposed pad and SO-16N lead-frame deliver robust thermal performance suited to automotive underhood and body electronics environments. Typical applications include automotive power windows, power seats, sunroofs, sliding doors, fuel pumps, and HVAC blowers, as well as industrial DC motor control in robotics, actuators, and small pumps. The wide 4 V to 28 V supply range makes it compatible with both 12 V and 24 V automotive battery systems including crank and load-dump transients within the protected envelope. When designing with the VNH7070ASTR, allocate sufficient PCB copper area on the drain tabs and exposed pad to keep junction temperature within SOA at continuous 15 A loads. Decouple VCC and VBS with low-ESR ceramics placed within 5 mm of the IC, route the high-current traces on inner or top-layer pours, and monitor the DIAG pin with the host MCU for graceful fault handling. This page synthesizes distributor pricing, drop-in alternatives, and practical PCB/thermal design notes not found in the manufacturer datasheet alone.

RFQ پەیوەندی
VNH7100ASTR - Automotive H-Bridge Motor Driver 30A | STMicroelectronics
VNH7100ASTR

VNH7100ASTR - Automotive H-Bridge Motor Driver 30A | STMicroelectronics

The STMicroelectronics VNH7100ASTR is a fully integrated full-bridge (H-bridge) motor driver intended for a wide range of automotive applications, housed in a 16-pin SO (SOIC-16N) power package with exposed thermal pad. It combines, on a single VIPower M0 die, two monolithic high-side drivers plus two low-side Power MOSFET switches, and provides a current rating up to 30 A continuous / 60 A peak with operating supply voltage from 4 V to 28 V. An H-bridge motor driver is a four-switch power stage that drives a brushed DC motor bidirectionally from a single supply. The IC integrates the four power switches plus their gate drivers, charge pump, protection logic, and diagnostic feedback into one package, eliminating the discrete MOSFET bridge and allowing compact PCB designs for DC motors, fans, pumps, and small actuators in automotive systems. H-bridge drivers belong to the broader category of motor-driver ICs, sitting within the power-management semiconductor family. Key features include very low RDS(on) high-side and low-side MOSFETs (typically in the tens of milliohm range per the VIPower M0 technology), built-in PWM current control up to 20 kHz, integrated charge pump, cross-conduction (shoot-through) protection, undervoltage/overvoltage shutdown, thermal shutdown, and a status flag output. The 16-pin SO package provides a low Rthja through the exposed thermal pad, enabling high continuous current without external heatsinking. The VNH7100ASTR uses ST's proprietary VIPower M0 smart-power technology, which co-integrates analog control logic, charge pump, and vertical Power MOSFETs on a single silicon die. This monolithic integration minimizes parasitic inductance and provides fast, well-matched switching for PWM frequencies up to 20 kHz while protecting against load-dump transients common in 12 V / 24 V automotive buses. Typical applications include automotive DC brushed motors for window lifts, seat adjusters, sliding doors, HVAC blowers, fuel pumps, and water/oil pumps. It is also used in industrial motion control where a robust, protected full-bridge driver is required. The wide 4 V to 28 V supply range covers both 12 V and 24 V bus systems. When designing with the VNH7100ASTR, ensure that the PCB provides a sufficiently large copper pour under the exposed thermal pad to dissipate up to ~5 W continuous load. PWM frequency should stay within the datasheet range to prevent cross-conduction; use an RC network on the inputs to control dV/dt and EMI. Note: this part is currently NRND (Not Recommended for New Designs); for new designs consider VNH7100BASTR (successor) or equivalent cross-brand options. This page synthesizes distributor pricing, drop-in alternatives, application notes, and design guidance not found in the manufacturer datasheet alone.

RFQ پەیوەندی
VNH7100BASTR - 12A Automotive H-Bridge Motor Driver | STMicroelectronics
VNH7100BASTR

VNH7100BASTR - 12A Automotive H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH7100BASTR is an automotive-grade fully integrated H-bridge motor driver delivering up to 12 A continuous output current from a 4 V to 28 V supply rail, housed in a 16-pin PowerSSO-16 package with an exposed thermal pad. The device combines a dual monolithic high-side driver and two low-side switches using ST's proprietary VIPower M0 technology, allowing a true power stage and intelligent protection circuitry on the same silicon die. It is qualified to AEC-Q100 standards for harsh automotive environments with an operating junction temperature range of -40 °C to +150 °C. An H-bridge motor driver is a power management IC that controls the direction and speed of a brushed DC motor by selectively activating four switches in an H configuration. It belongs to the broader hierarchy of motor drivers -> motion controllers -> power management ICs -> semiconductors. The VNH7100BASTR integrates the full H-bridge and the gate-drive/protection logic in one package, eliminating the bulk of discrete MOSFET bridges, gate drivers, and current-sense amplifiers. Key features include a 60 mΩ typ. on-resistance per high-side switch that minimizes conduction loss, PWM control up to 20 kHz for precise speed regulation, and a comprehensive protection suite: undervoltage lockout, overvoltage clamp, thermal shutdown with auto-restart, and load current limitation. A dedicated diagnostic feedback pin reports fault conditions to the host MCU. The PowerSSO-16 exposed pad provides a low thermal resistance path, supporting 12 A continuous operation with proper PCB copper. Typical applications include 12 V automotive brushed DC loads such as power window lifters, seat adjusters, mirror fold actuators, HVAC flaps, and door lock motors. The wide 4 V to 28 V supply range also suits industrial 24 V brush DC drives and battery-powered robotics where a single-IC H-bridge simplifies BOM and PCB area. When designing with this device, dedicate at least 1 sq in of top-side copper to the exposed pad and stitch a 4×4 thermal via array to the inner/inner-outer copper planes to keep junction temperature in spec. Place a 100 nF X7R ceramic bypass within 2 mm of the VCC pin and a bulk 47 µF electrolytic at the motor connector. Use a gate resistor or RC snubber on the PWM input if long MCU traces cause ringing above 5 MHz. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, giving engineers a single decision-ready resource for selecting and implementing the VNH7100BASTR in automotive and industrial brushed DC motor designs.

USD $2.79 پەیوەندی
VNH9030AQ - 30A Automotive H-Bridge Motor Driver | STMicroelectronics
VNH9030AQ

VNH9030AQ - 30A Automotive H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNH9030AQ is a fully integrated H-bridge motor driver designed for automotive and industrial DC motor control applications. It delivers a continuous output current of 30A and operates from a supply voltage range of 4V to 28V, making it suitable for a wide variety of brushed DC motor loads. The device is housed in a 32-pin VFQFPN (5x5 mm) package with an exposed pad for enhanced thermal performance. An H-bridge motor driver is a power management IC that allows bidirectional control of a DC motor by selectively enabling four power transistors in a bridge configuration. The VNH9030AQ integrates the power stage, gate drivers, and protection circuitry in a single package, simplifying PCB design and reducing component count compared to discrete implementations. This integration places the VNH9030AQ within the power management IC hierarchy, specifically under motor drivers, which are essential for automotive systems such as power windows, seat adjustment, and cooling fans. Key features of the VNH9030AQ include a low on-resistance of 25 mOhm per switch, which minimizes power dissipation and improves efficiency. The device provides a PWM frequency range up to 20 kHz, enabling precise speed control with minimal audible noise. It also includes comprehensive protection features such as undervoltage lockout, overcurrent protection, thermal shutdown, and a diagnostic output for fault reporting. These features ensure robust operation in harsh automotive environments. The VNH9030AQ utilizes STMicroelectronics' VIPower M0 technology, which integrates the control logic and power MOSFETs on a single die. This architecture reduces parasitic inductance and improves switching performance. The device supports both parallel and bridge operating modes, offering flexibility for different motor control topologies. The integrated current sense output provides real-time motor current monitoring, enabling closed-loop control algorithms. Typical applications include automotive body control modules, DC motor drivers for power seats, window lifts, and HVAC actuators, as well as industrial automation and robotics. The wide supply voltage range and high current capability make it suitable for both 12V and 24V systems. In automotive applications, the VNH9030AQ can be directly interfaced with a microcontroller via its standard logic-level inputs, simplifying system design. When designing with the VNH9030AQ, ensure adequate PCB copper area for thermal dissipation, as the device can dissipate significant power at high currents. The exposed pad must be soldered to a thermal via array to maintain junction temperature within safe limits. Additionally, place a 100nF ceramic capacitor close to the supply pins to suppress high-frequency noise and a bulk electrolytic capacitor to handle current transients.

RFQ پەیوەندی
VNHD7012AY - Automotive H-Bridge Motor Driver | STMicroelectronics
VNHD7012AY

VNHD7012AY - Automotive H-Bridge Motor Driver | STMicroelectronics

The VNHD7012AY is an automotive-grade H-bridge motor driver from STMicroelectronics, designed for driving DC motors in 12V and 24V automotive systems. It integrates a fully protected dual high-side driver and the drivers and protections for two external power MOSFETs in a low-side configuration, enabling a complete H-bridge with minimal external components. The device is housed in a 36-lead PowerSSO-36 package with an exposed pad for enhanced thermal dissipation. An H-bridge motor driver is a power management IC that controls the direction and speed of a DC motor by selectively switching four transistors in an 'H' configuration. It is a critical component in automotive systems such as power windows, seat adjusters, steering column actuators, and HVAC actuators. The VNHD7012AY belongs to the VIPower M0-7 family, which combines a true PowerMOSFET with intelligent signal and protection circuitry on a single die, simplifying design and improving reliability. Key features include a wide operating voltage range of 4V to 28V, a maximum output current of 38A (as referenced in the EV-VNHD7012AY reference design), and a low ON-state resistance that minimizes power dissipation. The device provides comprehensive protection including load current limitation, overtemperature shutdown, overvoltage clamp, and loss of ground protection. It also features a PWM input for speed control and a diagnostic output for fault detection. The VNHD7012AY uses STMicroelectronics' proprietary VIPower technology, which integrates a vertical power MOSFET with intelligent control circuitry. This architecture enables efficient switching, low quiescent current, and robust protection against automotive transients. The PowerSSO-36 package, with its exposed pad, provides a thermal resistance suitable for high-current applications when properly connected to a PCB copper area. Typical applications include automotive DC motor driving for power windows, sunroofs, seat adjustment, steering column tilt/telescope, and HVAC actuators. The device is also suitable for industrial DC motor control where 12V or 24V supplies are used. Its high current capability and protection features make it ideal for driving motors that require bidirectional control and PWM speed regulation. When designing with the VNHD7012AY, ensure adequate PCB copper area for thermal management, especially at high output currents. The two external low-side MOSFETs must be selected to match the motor's current and voltage requirements, and proper gate drive connections must be made to the device's gate driver outputs.

RFQ پەیوەندی
VNHD7012AYTR - 28V, 12A H-Bridge Motor Driver | STMicroelectronics
VNHD7012AYTR

VNHD7012AYTR - 28V, 12A H-Bridge Motor Driver | STMicroelectronics

The STMicroelectronics VNHD7012AYTR is a monolithic H-bridge motor driver designed for automotive and industrial DC motor control applications. It integrates two half-bridges with a maximum continuous output current of 12A per channel and supports an operating supply voltage range of 4V to 28V. The device is housed in a 36-pin PowerSSO-36 package with exposed thermal pad, enabling efficient heat dissipation in high-current applications. An H-bridge motor driver is a power management IC that controls the direction and speed of a DC motor by selectively turning on four transistors in an H-shaped configuration. It is a type of motor driver, which falls under the broader category of power management ICs. The VNHD7012AYTR integrates the power stage, gate drivers, and protection features, simplifying the design of bidirectional motor control systems. Key features include a low ON-resistance of 25 mOhm per channel, which minimizes power losses and heat generation. The device provides PWM control up to 20 kHz, enabling precise speed regulation. It includes comprehensive protection features such as undervoltage lockout, overvoltage clamp, overcurrent protection, and thermal shutdown, ensuring robust operation in harsh environments. The logic inputs are 3.3V and 5V compatible, allowing direct interface with microcontrollers. The VNHD7012AYTR uses a high-side and low-side driver architecture with integrated bootstrap diodes for the high-side gate drive. It features a current sense output that provides a proportional current signal for closed-loop control. The device is AEC-Q100 qualified, making it suitable for automotive applications. Its PowerSSO-36 package offers a thermal resistance of 30 C/W, allowing operation at high currents with proper PCB copper area. Typical applications include automotive power windows, sunroofs, seat adjustment, and industrial DC motor control. The device's wide voltage range and high current capability make it ideal for driving brushed DC motors in body control modules and industrial actuators. When designing with this device, ensure adequate PCB copper area for thermal management, especially at high output currents. The current sense pin should be connected to a low-value sense resistor for accurate current monitoring. Proper decoupling capacitors on the supply pins are essential to minimize voltage transients during switching.

RFQ پەیوەندی