Power Management
ژێرپۆلەکان
بەرهەمەکان (2,800+)
STGAP1BS - 4A Galvanically Isolated Single Gate Driver | STMicroelectronics
The STGAP1BS is a galvanically isolated single gate driver from STMicroelectronics, designed to drive high-power IGBTs and SiC MOSFETs in industrial and automotive applications. It provides a 4A sink/source peak output current and features a 4 kV galvanic isolation barrier, making it suitable for motor drives, power supplies, and renewable energy inverters. The device is available in a wide-body SO-8W package, which offers a compact footprint while maintaining high isolation voltage. A gate driver is a power amplifier that accepts a low-power input from a controller IC and produces a high-current drive output to control the gate of a power transistor. In the hierarchy of power electronics, a gate driver sits between the control stage (microcontroller or DSP) and the power stage (IGBT or MOSFET), ensuring fast and reliable switching. The STGAP1BS integrates a galvanic isolation barrier, which separates the input and output grounds, protecting the low-voltage control circuitry from high-voltage transients and ground loops. Key features of the STGAP1BS include a 4A peak output current, 4 kV galvanic isolation, 100 V/ns common-mode transient immunity (CMTI), and a wide supply voltage range from 4.5V to 18V on the output side. The device also features a Miller clamp function to prevent spurious turn-on during high dv/dt events, and a desaturation protection input for overcurrent detection. These features make it ideal for driving SiC MOSFETs and IGBTs in high-frequency, high-efficiency power converters. The STGAP1BS uses STMicroelectronics' proprietary galvanic isolation technology, which provides robust isolation with low propagation delay (typically 75 ns) and tight part-to-part matching. The device supports both bipolar and unipolar supply configurations, allowing flexible design for various gate drive requirements. The wide-body SO-8W package ensures adequate creepage and clearance distances for 4 kV isolation, meeting IEC 60747-17 requirements. Typical applications include motor drives for industrial automation, solar inverters, uninterruptible power supplies (UPS), and electric vehicle (EV) charging stations. The STGAP1BS is also suitable for welding equipment and induction heating systems, where high reliability and fast switching are critical. When designing with the STGAP1BS, ensure proper PCB layout to minimize parasitic inductance in the gate drive loop. Use a low-ESR capacitor close to the VCC and GND pins to supply the high peak currents. The Miller clamp pin should be connected to the gate of the power transistor with a short, low-inductance trace to effectively suppress dv/dt-induced turn-on.
STGAP2HSA - 4A Galvanically Isolated Gate Driver | STMicroelectronics
The STGAP2HSA is a galvanically isolated single-channel gate driver from STMicroelectronics, designed to drive high-power IGBTs and SiC MOSFETs in industrial and automotive applications. It delivers up to 4A of peak output current with a wide supply voltage range of 3V to 18V on the primary side and 4.5V to 18V on the secondary side. The device features a 100V/ns common-mode transient immunity (CMTI) and a propagation delay of 75ns, ensuring robust performance in noisy power environments. A galvanic isolation barrier is a critical safety feature in power electronics that electrically separates the low-voltage control circuitry from the high-voltage power stage, preventing ground loops and protecting sensitive logic. The STGAP2HSA uses a capacitive isolation technology that provides reinforced isolation up to 6kV, meeting stringent safety standards for industrial motor drives and solar inverters. This isolation barrier is essential in applications where the control and power grounds are at different potentials, such as in half-bridge or full-bridge topologies. Key features of the STGAP2HSA include a 4A sink/source peak current, a 75ns propagation delay, and a 100V/ns CMTI. The device also offers a programmable dead time function, a shutdown pin for fault protection, and a separate output pin for Miller clamp, which prevents spurious turn-on of the power switch during high dv/dt events. The wide supply voltage range and rail-to-rail output make it compatible with a variety of gate drive circuits. The STGAP2HSA is built using STMicroelectronics' proprietary galvanic isolation technology, which uses a high-voltage capacitor to transfer signals across the isolation barrier. This architecture achieves low power consumption and high reliability, with a typical quiescent current of 1.5mA on the primary side. The device is available in a compact SO-8 package, which simplifies PCB layout and reduces board space in space-constrained designs. Typical applications include industrial motor drives, solar inverters, uninterruptible power supplies (UPS), and electric vehicle (EV) charging systems. In motor drives, the STGAP2HSA drives the IGBTs in the inverter stage, providing fast and reliable switching to minimize losses. In solar inverters, it drives the SiC MOSFETs in the boost converter, enabling high-frequency operation and improved efficiency. When designing with the STGAP2HSA, it is important to ensure proper PCB layout to minimize parasitic inductance in the gate drive loop. The Miller clamp output should be connected to the gate of the power switch to prevent false turn-on. Additionally, the dead time programming pin should be configured with an external resistor to set the desired dead time for the application.
STGAP2SA - 4A Galvanic Isolated Single Gate Driver | STMicroelectronics
The STGAP2SA is a galvanic isolated single gate driver manufactured by STMicroelectronics, designed to drive wide-bandgap power switches such as SiC MOSFETs and GaN HEMTs. It provides a 4A sink/source peak output current and features a 4 kV galvanic isolation barrier, making it suitable for high-voltage and high-reliability applications. The device is available in a narrow-body SO-8 package, which is compact and suitable for space-constrained designs. A galvanic isolated gate driver is a type of gate driver IC that provides electrical isolation between the input control side and the output power stage. This isolation is critical in applications where the power stage operates at high voltages, as it protects the low-voltage control circuitry from transients and ground potential differences. The STGAP2SA belongs to the category of isolated gate drivers, which are essential components in power electronics systems such as motor drives, power supplies, and inverters. Key features of the STGAP2SA include a 4A peak output current, a wide supply voltage range of 3V to 18V on the output side, and a 4 kV galvanic isolation rating. The device also offers a propagation delay of 75 ns, which is critical for high-frequency switching applications. The input side operates from 3V to 18V, and the device includes a Miller clamp function to prevent false turn-on of the power switch during high dv/dt events. The STGAP2SA utilizes STMicroelectronics' proprietary galvanic isolation technology, which provides robust isolation performance with high common-mode transient immunity (CMTI) of 100 V/ns. This ensures reliable operation in noisy environments. The device also features an under-voltage lockout (UVLO) on both the input and output sides, protecting the power switch from insufficient gate drive voltage. Typical applications for the STGAP2SA include motor drives, industrial power supplies, solar inverters, and electric vehicle (EV) charging systems. Its high output current and fast propagation delay make it suitable for driving SiC MOSFETs and GaN HEMTs in high-frequency power converters. The device is also used in welding equipment and induction heating systems where high reliability and isolation are required. When designing with the STGAP2SA, it is important to ensure proper PCB layout to minimize parasitic inductance and maintain isolation creepage distances. The Miller clamp feature should be utilized in applications with high dv/dt to prevent unintended turn-on. Additionally, the UVLO thresholds should be considered to ensure the gate driver operates within the specified voltage range.
STGAP4S - 4-Channel Isolated Gate Driver | STMicroelectronics
The STGAP4S is a 4-channel isolated gate driver from STMicroelectronics, designed for driving IGBTs and MOSFETs in high-voltage applications. It provides four independent galvanically isolated channels, each capable of delivering up to 4 A peak output current, making it suitable for three-phase inverters, motor drives, and industrial power supplies. The device operates from a supply voltage range of 4.5 V to 18 V on the logic side and 4.5 V to 18 V on the driver side, with a common-mode transient immunity (CMTI) of 100 V/ns, ensuring robust operation in noisy environments. An isolated gate driver is a type of gate driver that provides electrical isolation between the control circuitry and the power stage, protecting low-voltage logic from high-voltage transients and ground loops. It is a critical component in power electronics, enabling safe and reliable switching of power semiconductors. The STGAP4S belongs to the category of isolated gate drivers, which are part of the broader family of gate drivers, power management ICs, and semiconductor devices. Key features of the STGAP4S include a 4 A peak output current per channel, a wide supply voltage range, and a propagation delay of 100 ns. It also features an interlock function to prevent cross-conduction, a dedicated enable pin for each channel, and a fault output for system monitoring. The device is available in a 36-pin SSOP package, offering a compact solution for multi-channel gate drive applications. The STGAP4S utilizes STMicroelectronics' galvanic isolation technology, providing reinforced isolation up to 6 kV. The device includes a Miller clamp on each channel to prevent spurious turn-on of the power switch, and a desaturation protection feature for overcurrent detection. The architecture ensures high noise immunity and reliable operation in harsh industrial environments. Typical applications include motor drives, three-phase inverters, uninterruptible power supplies (UPS), and industrial power supplies. The STGAP4S is also suitable for renewable energy systems such as solar inverters and wind turbine converters. Its high CMTI and low propagation delay make it ideal for high-frequency switching applications. When designing with the STGAP4S, it is important to ensure proper PCB layout to minimize parasitic inductance and maintain signal integrity. The device requires careful attention to the isolation barrier and creepage distances to meet safety standards. Additionally, the supply decoupling should be implemented with low-ESR capacitors close to the VCC and GND pins.
STGIPS20C60-H - 600V 20A 3-Phase IGBT IPM | STMicroelectronics
The STMicroelectronics STGIPS20C60-H is a 600 V, 20 A three-phase IGBT Intelligent Power Module (IPM) from the SLLIMM (Small Low-Loss Intelligent Molded Module) family, integrating gate drivers and short-circuit rugged trench-gate IGBTs in a 25-pin PowerDIP module measuring 0.993 inch (25.23 mm) wide. It is designed as a compact, drop-in inverter stage for variable-frequency drives and is rated for 600 V collector-emitter blocking with 20 A continuous phase current, plus an integrated bootstrap diode network, undervoltage lockout, and an on-board comparator for fault/over-current sensing via an external shunt resistor. What is an Intelligent Power Module (IPM)? An IPM is a power semiconductor module that integrates the power switches (here: IGBTs), their gate drivers, and protection features (UVLO, short-circuit, fault output) into a single isolated package. IPMs sit in the power management hierarchy between discrete IGBT/MOSFET inverter stages and higher-level integrated motor-drive modules, simplifying PCB design and shortening time-to-market for three-phase motor control applications such as HVAC compressors, washing-machine pumps, and small industrial inverters. Key features include 600 V short-circuit rugged IGBTs with trench-gate field-stop technology for low VCE(sat) and soft switching, a built-in shunt-style comparator with internal Vref and external CIN pin for hardware over-current protection, undervoltage lockout on all six driver channels, an open-drain fault output, and interlock logic that prevents shoot-through. The molded 25-PowerDIP package provides reinforced insulation and a thermally conductive substrate that simplifies heatsink attachment versus discrete through-hole designs. Typical applications include three-phase motor drives for white goods (washing machines, refrigerators, dishwasher pumps), low-power industrial variable-frequency drives (VFDs) up to about 1.5 kW, fan and compressor inverters for HVAC, and small servo pumps. The IPM's 20 A rating makes it suitable for 230 V AC mains-fed systems driving motors in the 0.37-1.1 kW range. When designing with this device, route the bootstrap capacitors close to pins U, V, W and ensure the comparator CIN pin is filtered to avoid nuisance trips. The internal Vref is non-adjustable, so over-current threshold is set by the external shunt resistor value only.
STLED316SMTR - 6-Digit LED Controller w/ Key Scan, SO-24 | STMicroelectronics
The STMicroelectronics STLED316SMTR is a serial-interfaced 6-digit LED controller with integrated key-scan, designed to drive 7-segment displays through a compact 3-wire SPI-compatible interface. It provides 14 constant-current sink outputs (8 segment lines + 6 digit lines) with 40 mA per-segment drive capability, while a 2x2 key-scan matrix supports up to 4 key inputs. The part operates from a 4.5 V to 5.5 V supply (3 V LED front-panel applications) and is offered in a 24-pin SO-24 small-outline surface-mount package with tape-and-reel packaging for high-volume assembly. What is an LED display controller? An LED display controller (sometimes called an LED driver or display bias IC) is an interface device that sits between a microcontroller and a multiplexed 7-segment or dot-matrix LED panel. It receives display data over a low-pin-count serial bus (SPI, I2C, or proprietary) and re-drives each segment at the correct duty cycle, freeing the host MCU from software multiplexing. In the broader taxonomy, LED display controllers sit beneath LED Drivers -> Power Management -> Power & Interface ICs, and they are distinct from simple LED current sinks because they integrate the timing, brightness, and key-scan logic required for human-machine interface (HMI) panels. Key features of the STLED316SMTR include 14 open-drain segment/digit outputs rated at 40 mA continuous, integrated 3-wire serial interface (clock, data, strobe) compatible with SPI mode 0, hardware key-scan with on-chip debounce, low standby current to support battery-backed panels, and a wide industrial operating temperature range. The device is also designed for minimum external BOM - only the segment current-setting resistor and decoupling caps are required, allowing very compact front-panel PCBs. Typical applications include white-good front panels (washing machines, microwaves, ovens), industrial control HMIs, point-of-sale (POS) terminals, audio equipment displays, instrument cluster readouts, and any 6-digit or smaller 7-segment user interface requiring keypad scanning. With 8 segment + 6 digit outputs the controller can drive a 6-digit 7-segment display plus decimal points, or up to 8 separate status LEDs. When designing with the STLED316SMTR, observe the absolute maximum segment current rating and choose the external RSET resistor accordingly. Ensure the 3-wire interface timing matches SPI mode 0 (CPOL=0, CPHA=0) of the host MCU, and place the decoupling capacitor as close as possible to VDD to suppress key-scan glitches during display multiplexing. This page synthesises distributor pricing, parametric comparison with same-brand and cross-brand drop-in alternatives, and practical design notes that complement - but do not replace - the official STMicroelectronics datasheet.
STLQ020PUR - 200mA Ultra-Low Iq LDO 2V-5.5V | STMicroelectronics
The STMicroelectronics STLQ020PUR is a 200 mA ultra-low quiescent current LDO linear regulator delivering an adjustable output from 0.8 V to 4.5 V from a 2 V to 5.5 V input rail, housed in a 6-pin DFN (2x2 mm) exposed-pad package. Designed for battery-powered applications, the regulator achieves a typical quiescent current that helps extend standby runtime across wireless sensor nodes, wearables, and IoT end nodes. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage by dissipating excess energy as heat, even when the input-to-output voltage differential is very small. LDOs sit within the broader hierarchy of power management ICs and are typically chosen over switching regulators in noise-sensitive or low-power applications because they introduce no switching ripple and require only small input/output capacitors. The STLQ020 belongs to the "ultra-low quiescent current" sub-category, where nanoamp-level Iq enables multi-year battery life in always-on systems. Key features of the STLQ020PUR include a 160 mV typical dropout at full 200 mA load, an enable pin that drops total current consumption to 5 nA in shutdown, and stable operation with low-ESR ceramic output capacitors as small as 1 uF. Built-in protections include thermal shutdown and short-circuit current limiting, and the exposed-pad package keeps junction temperature rise manageable at typical 50-100 mA portable loads. Internally, the regulator uses a CMOS pass element driven by a precision bandgap reference and an error amplifier optimized for low bias current. Compared with bipolar LDOs of similar rating, this CMOS architecture keeps quiescent current in the low microamp range even during dropout, which is critical when the battery voltage approaches the regulated rail and the regulator is barely regulating. Typical applications include coin-cell-powered IoT nodes, wearables and hearables, remote controls, BLE/Zigbee sensor modules, and standby rails of always-on microcontrollers. The wide enable range and tiny DFN-6 footprint also make it suitable as a post-regulator following a switching pre-regulator in space-constrained PMUs. When designing with the STLQ020PUR, keep the trace from ADJ pin to the feedback resistor divider short to minimize noise pickup, place the input/output ceramic capacitors within 1-2 mm of the package, and verify that worst-case VIN minus VOUT does not exceed the 160 mV dropout budget at peak load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Distributor stock and pricing were verified against DigiKey and Mouser as of 2026-10-10.
STNRG011ATR - Digital Power Controller for SMPS | STMicroelectronics
The STNRG011ATR is a digital power controller from STMicroelectronics designed for switched-mode power supplies (SMPS). It integrates a digital control core with a high-voltage startup cell, making it suitable for flyback, buck, and boost converter topologies. The device operates from an input voltage range of 8.5V to 23V and provides a gate drive output capable of sourcing 0.5A and sinking 0.8A. It is housed in a 16-pin SO-16 package, offering a compact solution for power supply designs. A digital power controller is a type of power management IC that uses digital signal processing to regulate output voltage and current, replacing traditional analog control loops. It sits within the hierarchy of power management ICs, which include linear regulators, switching regulators, and digital power controllers. Digital controllers offer advantages such as programmability, higher efficiency, and better transient response compared to analog counterparts. Key features of the STNRG011ATR include a programmable switching frequency up to 1 MHz, an integrated high-voltage startup cell that reduces standby power consumption, and a digital control loop that can be configured via an I2C interface. The device also includes protection features such as overcurrent protection, overvoltage protection, and thermal shutdown, ensuring reliable operation in demanding environments. The STNRG011ATR utilizes a digital control architecture with a dedicated state machine and a configurable PID compensator. This allows designers to optimize the control loop for specific power stage characteristics without changing external components. The integrated high-voltage startup cell enables fast startup and low standby power, making it ideal for applications requiring energy efficiency standards compliance. Typical applications include AC-DC adapters, USB Power Delivery (USB-PD) chargers, and industrial power supplies. The device's digital control capability allows for precise voltage and current regulation, which is essential for USB-PD applications that require multiple output voltage levels. Its wide input voltage range and high switching frequency support compact transformer designs, reducing overall solution size. When designing with the STNRG011ATR, ensure proper layout of the high-voltage startup cell and gate drive traces to minimize parasitic inductance. The I2C interface should be isolated from high-voltage areas to prevent noise coupling. Additionally, the thermal pad should be connected to a large copper area for effective heat dissipation.
STNRG388ATR - Digital Power Controller for SMPS | STMicroelectronics
The STNRG388ATR is a digital power controller from STMicroelectronics designed for switched-mode power supplies (SMPS). It integrates a digital control core with analog peripherals to enable high-efficiency, flexible power conversion in applications such as AC-DC adapters, USB-PD chargers, and industrial power supplies. The device is offered in a compact surface-mount package, suitable for space-constrained designs. A digital power controller is a specialized microcontroller or ASIC that manages the operation of a power converter, such as a flyback or LLC resonant converter, using digital algorithms instead of analog feedback loops. It sits within the power management hierarchy, typically between the power stage (MOSFETs, transformers) and the system load, providing precise voltage and current regulation, protection, and communication interfaces. Digital controllers enable adaptive control, remote monitoring, and firmware updates, which are increasingly important in modern power systems. Key features of the STNRG388ATR include a high-performance digital core, multiple PWM outputs for driving power switches, integrated analog-to-digital converters (ADCs) for sensing voltage and current, and communication interfaces such as I2C or UART for system integration. It supports various control topologies, including flyback, LLC, and PFC, making it versatile for different power supply designs. The device also includes protection features like overvoltage, overcurrent, and overtemperature shutdown, enhancing system reliability. From a technical perspective, the STNRG388ATR leverages STMicroelectronics' expertise in digital power control, offering a balance of performance and integration. The digital core executes control algorithms with high resolution, enabling tight output regulation and fast transient response. The integrated ADCs provide accurate sensing, while the PWM generators offer flexible dead-time and frequency control. This architecture reduces external component count and simplifies design compared to analog controllers. Typical applications include AC-DC adapters for laptops and mobile devices, USB-PD chargers, LED drivers, and industrial power supplies. In these applications, the STNRG388ATR enables high efficiency, low standby power, and compliance with energy standards. Its digital nature allows for easy tuning and optimization during development, reducing time-to-market. When designing with the STNRG388ATR, engineers should consider the need for a stable power supply for the controller itself, proper decoupling of analog and digital sections, and careful layout of the power stage to minimize noise. The device's firmware must be developed and validated to ensure reliable operation across all load conditions. Reference designs and application notes from STMicroelectronics provide guidance for common topologies.
STPIC44L02PTR - 4-Channel Low-Side Pre-FET Driver | STMicroelectronics
STMicroelectronics STPIC44L02PTR is a four-channel, low-side pre-FET driver with four inputs and no outputs, operating from a 5 V supply and packaged in a 24-pin SSOP. The device provides a serial-in, parallel-out input interface, supports cascading, and includes an internal 55 V inductive-load clamp together with a VGS protection clamp for external power MOSFETs. A pre-FET driver is a gate-driver interface that conditions logic commands before they reach an external power MOSFET. In the broader semiconductor hierarchy, this device is a gate driver, which is a specialized interface IC within the power-management and driver ecosystem. Its low-side architecture means the controlled MOSFETs are connected between a load and ground, making it useful where the driver must source current into MOSFET gate terminals rather than sink current from a high-side floating gate network. The principal verified features are four independently addressed driver inputs, serial-in and parallel-in operation, cascading capability, independent shorted-load and short-to-battery protection functions, a 55 V internal inductive-load clamp, and VGS protection for external power FETs. The STPIC44L02PTR is identified as an automotive-temperature-grade component with a gull-wing SSOP package, making it suitable for demanding low-side switch-control systems where protected MOSFET gate drive is required. The serial-in, parallel-out organization allows commands to be shifted into the device through a serial interface and then presented to the corresponding MOSFET gates in parallel. This arrangement can simplify control wiring in multi-channel systems and provides an efficient path for cascading devices when more than four channels are required. Parallel operation provides a direct route for independent channel control where the host controller can drive the input interface directly. Typical uses include low-side MOSFET control in automotive body and comfort systems, relay and solenoid interfaces, inductive switching networks, industrial low-side switch stages, and protected external power-FET arrangements. The internal 55 V clamp is particularly relevant when an external MOSFET must tolerate an inductive event. Designers should still validate the complete power path, including load current, MOSFET avalanche capability, wiring inductance, and the exact protection behavior specified by the manufacturer. Design decisions should begin with the external MOSFET because STPIC44L02PTR is a pre-FET driver rather than a power-stage device. Verify that the selected MOSFET gate charge, gate threshold, maximum VGS, and avalanche rating support the intended switching conditions. Place the driver and protected MOSFETs so switching-loop inductance is minimized, while preserving adequate trace area and thermal paths for the power stage. This page consolidates the verified distributor and datasheet-search information for STPIC44L02PTR, identifies the confirmed protection features and package characteristics, and clearly separates documented data from parameters that still require confirmation from the complete manufacturer datasheet.
STPM066S - 66V Step-Down DC-DC Converter | STMicroelectronics
The STPM066S is a high-voltage step-down DC-DC converter from STMicroelectronics, designed to deliver efficient power conversion in industrial and automotive applications. It operates from a wide input voltage range of 4.5V to 66V, making it suitable for 12V, 24V, and 48V bus systems. The device provides a continuous output current of up to 3A, with an adjustable output voltage down to 0.8V. Housed in a compact QFN-16 package (4x4 mm), the STPM066S integrates high-side and low-side MOSFETs, reducing external component count and simplifying PCB layout. A step-down DC-DC converter, also known as a buck converter, is a type of switching regulator that efficiently reduces a higher input voltage to a lower output voltage. Unlike linear regulators, which dissipate excess power as heat, buck converters use inductive energy storage and high-frequency switching to achieve efficiencies often exceeding 90%. This makes them essential in power management systems where thermal budget and battery life are critical. The STPM066S belongs to the broader category of power management ICs, specifically within DC-DC converters, and is a key building block in distributed power architectures. Key features of the STPM066S include a peak efficiency of 95%, a switching frequency adjustable from 200kHz to 2.2MHz, and a low quiescent current of 40uA in light-load mode. The device also offers a precision enable pin with hysteresis, soft-start to limit inrush current, and comprehensive protection features including overcurrent, overvoltage, and thermal shutdown. The integrated MOSFETs have low RDS(on) of 80mOhm (high-side) and 40mOhm (low-side), minimizing conduction losses. Technically, the STPM066S employs a current-mode control architecture, providing fast transient response and stable operation with a wide range of output capacitors. The adjustable switching frequency allows designers to optimize efficiency versus component size, while the external compensation pin offers flexibility in loop tuning. The device is available in a QFN-16 package with an exposed thermal pad, achieving a thermal resistance of 25°C/W, enabling reliable operation at high ambient temperatures. Typical applications include industrial power supplies, automotive infotainment systems, battery-powered equipment, and distributed power architectures in telecom and networking equipment. The wide input range and high efficiency make it ideal for pre-regulation in multi-rail systems, where it steps down a high-voltage bus to an intermediate rail for downstream LDOs or point-of-load converters. When designing with the STPM066S, ensure proper input and output capacitor selection to minimize voltage ripple and maintain stability. The bootstrap capacitor for the high-side driver must be placed close to the BST pin, and the feedback network should be routed away from the inductor to avoid noise coupling. Adequate copper pour on the thermal pad is essential for heat dissipation at high output currents.
STPM32TR - 2-Channel Metering AFE, 4x 24-bit Sigma-Delta ADC | STMicroelectronics
The STMicroelectronics STPM32TR is an Application-Specific Standard Product (ASSP) designed for high-accuracy power and energy metering in power-line systems. The device integrates four independent 24-bit second-order sigma-delta analog-to-digital converters with a 4 MHz output sample frequency and two embedded Programmable Gain Low-Noise Amplifiers (PGLNA), housed in a 24-pin QFN (4x4 mm) package. A metering IC (or meter IC) is a specialized mixed-signal ASSP that combines analog front-end signal conditioning, ADC conversion, and digital computation in a single device to measure electrical parameters such as active, reactive, and apparent power, RMS voltage, RMS current, and energy consumption. Within the broader taxonomy, the STPM32TR sits at the intersection of power management ICs (PMIC) and data converters, serving the smart-grid and billing-meter market segment where IEC 62053 family compliance is mandatory. Key features of the STPM32TR include four 24-bit sigma-delta ADCs providing 0.5 percent accuracy over a 1:1000 dynamic range when paired with shunt or current-transformer (CT) sensors, on-chip PGLNAs eliminating external op-amps for current channels, integrated digital signal processing for instantaneous active/reactive/apparent power calculation, and a SPI/UART digital interface for host MCU communication. The ADC supports both Rogowski coil and CT or shunt current-sensing transducers, enabling flexible sensor selection. Architecturally, the STPM32TR uses synchronous sampling on both voltage and current channels, with the modulator oversampling clock feeding a hardware DSP block that computes power line-by-line at every cycle. The integrated PGLNA stages adapt gain across the dynamic range, providing 1:1000 dynamic range without saturation in high-current transient conditions. Typical applications include single-phase and dual-phase residential smart electricity meters, energy-monitoring sub-metering modules, solar inverter DC-side monitoring, EV charging-station metering front-ends, and industrial power-quality analyzers. The 24-QFN package and operating temperature range of -40C to +85C make the part suitable for compact sealed meter housings. A critical design consideration when using the STPM32TR is the anti-aliasing filter on each input channel - typically a first-order RC network with cutoff near 10 kHz for 50/60 Hz line frequencies. Designers should also implement glitch detection on the neutral channel when the meter must detect tamper events, and validate the DC-bias calibration routine against the chosen CT or shunt current sensor. This page synthesizes distributor stock and price data, drop-in alternative parts, and application-level design notes that are not consolidated on the manufacturer datasheet alone.
STPM801 - Programmable Current Limiting Switch | STMicroelectronics
The STPM801 is a programmable current limiting switch from STMicroelectronics, designed for power distribution and protection in a wide range of applications. It integrates a high-side MOSFET switch with programmable current limiting, thermal shutdown, and under-voltage lockout, providing robust protection for downstream circuitry. The device operates from an input voltage range of 2.7V to 5.5V and can deliver up to 1.5A of continuous current, making it suitable for USB ports, hot-swap applications, and general power management. A current limiting switch is a type of power management IC that controls the flow of electrical current to a load, protecting the power source and the load from overcurrent conditions. It is a key component in the power management hierarchy, sitting between the power source (such as a battery or USB port) and the load (such as a peripheral device). By integrating a MOSFET switch, current sensing, and protection features, it simplifies circuit design and enhances system reliability. Key features of the STPM801 include programmable current limiting via an external resistor, allowing designers to set the current limit from 100mA to 1.5A. It also features a low quiescent current of 50µA, a fast 1ms turn-on time, and a low on-resistance of 70mΩ, minimizing power loss. The device includes thermal shutdown at 150°C and under-voltage lockout at 2.5V, ensuring safe operation under fault conditions. It is available in a compact SOT-23-5 package, ideal for space-constrained designs. The STPM801 uses a high-side N-channel MOSFET architecture with an internal charge pump to drive the gate, enabling low voltage drop and efficient power delivery. The current limit is set by an external resistor connected to the ILIM pin, providing flexibility for different applications. The device also features a fault output pin that signals overcurrent or thermal shutdown events, enabling system-level monitoring and control. Typical applications include USB port power distribution, hot-swap power management, and general-purpose load switching in consumer electronics, industrial control, and automotive systems. The wide input voltage range and programmable current limit make it versatile for various power distribution scenarios. When designing with the STPM801, ensure the external current-limit resistor is placed close to the ILIM pin to minimize parasitic inductance. The input and output capacitors should be placed near the device to ensure stable operation and reduce voltage transients. Proper thermal management is essential when operating at high currents, as the device dissipates power proportional to the current and voltage drop.
STR-W6072S - 72W Off-Line PWM Controller w/ MOSFET | Sanken
The Sanken STR-W6072S is an off-line switching power supply controller IC with an integrated power MOSFET, housed in a TO-220F-5 (formed-leads) package. It operates in a fixed-frequency current-mode PWM topology between 60 kHz and 74 kHz, targets flyback converter designs up to approximately 72 W output, and combines the power switch and control circuitry on a single die to reduce BOM count in cost-sensitive adapters and auxiliary supplies. A switching power supply controller (also called an AC-DC converter IC or PWM controller IC) is a semiconductor that regulates output voltage in a switch-mode power supply (SMPS) by modulating the duty cycle of an internal or external power switch at high frequency. The STR-W6072S belongs to the AC-DC converter sub-category of power management ICs (PMICs), sitting inside a flyback converter topology that is the dominant architecture for sub-100 W isolated supplies such as appliance adapters, set-top box wall warts, and standby rails for white goods. Within the device, a current-mode PWM controller IC is co-packaged with a power MOSFET, eliminating the drive loop between separate controller and MOSFET components. Key features include integrated avalanche-rated 650 V MOSFET, automatic standby/burst-mode operation for sub-100 mW standby power, built-in soft-start, over-current protection (OCP) with auto-restart, over-voltage protection (OVP), thermal shutdown, and an under-voltage lockout (UVLO) on the VCC pin. The auxiliary winding feedback topology sets output voltage indirectly via the VCC supply, removing the need for an opto-isolator and TL431 in low-cost designs. The internal architecture uses a current-mode PWM control loop with leading-edge blanking, slope compensation, and a built-in oscillator. The Sanken STR-W6000S series is positioned as a cost-performance optimized family for digital TV, monitor, and appliance standby power, where the controller integrates the high-voltage startup circuit and eliminates external bias components. Compared to a discrete UC3842 + MOSFET implementation, the STR-W6072S achieves a much smaller PCB footprint and lower standby power, at the expense of peak output power ceiling. Typical applications include AC-DC adapters up to 72 W, auxiliary/standby supplies for white goods and industrial equipment, digital TV and monitor main power supplies, set-top box power bricks, and low-cost isolated DC-DC converters. Designers typically use it in quasi-resonant or hard-switched flyback configurations with a simple single-winding auxiliary feedback. When designing with the STR-W6072S, ensure the VCC auxiliary winding is wound to deliver 15 V to 20 V at nominal load so that VCC stays within the 8.5 V to 18 V operating range. Verify that peak drain current does not exceed the integrated MOSFET rating, and add a Y-capacitor and adequate common-mode choke on the input for EMI suppression to meet EN55022 Class B. This page synthesizes Sanken's official datasheet, current distributor pricing, verified drop-in alternatives in the same TO-220F footprint, and practical flyback design notes that are not collected in the equivalent value of a single product listing.
STR-W6072S - Off-Line PWM Controller with 800V MOSFET | Sanken
The Sanken STR-W6072S is an off-line PWM controller with an integrated 800V power MOSFET in a TO-220-5 (TO-220F-6 formed leads) package, designed for AC/DC flyback converters in the 60 kHz to 74 kHz switching range. It combines a current-mode PWM controller IC and a high-voltage avalanche-rugged MOSFET on one die, enabling compact, low-component-count SMPS designs. The STR-W6000S series targets cost-sensitive auxiliary and standby power supplies where a few external parts and built-in protection are required. An off-line PWM controller with integrated MOSFET (sometimes called a Power IC or Power Supply Control IC) is a category of power-management semiconductor that replaces a discrete PWM controller plus external MOSFET pair. Within the system hierarchy, this device sits between an analog PWM controller IC and a high-voltage switching MOSFET, integrating both functions to reduce BOM count and simplify EMI layout. The integrated approach also shortens high-current loops between the MOSFET drain, the transformer primary, and the controller's current-sense input, lowering radiated EMI. The STR-W6072S operates from a universal AC input (via a rectified 100 V to 400 V DC bus) and incorporates an auto-standby function that switches between normal PWM operation and burst oscillation under light-load conditions. This auto-standby behavior yields low standby power consumption, helping designs meet modern energy-efficiency regulations for home appliances and consumer electronics. Built-in protections include over-current protection (OCP), over-voltage protection (OVP), and thermal shutdown. Internally the device uses a current-mode control topology with slope-compensated peak current sensing through the MOSFET source. The integrated MOSFET's avalanche rating is published for unclamped inductive switching events, simplifying snubber design. Operating frequency is trimmed across the 60 kHz to 74 kHz band, allowing the designer to optimize transformer size versus switching loss. According to the manufacturer datasheet, fault protection covers over-temperature and over-voltage events, with thermal shutdown typically engaging above 150 °C junction. Typical applications for the STR-W6072S include low-to-medium-power AC/DC adapters, auxiliary and standby supplies in white goods, set-top box power supplies, and small appliance SMPS modules up to roughly 50 W output. Its 800 V drain rating provides wide margin on 265 V AC rectified inputs where reflected voltage spikes can stress the primary switch. When designing with the STR-W6072S, thermal management of the TO-220-5 tab is critical: the exposed metal tab is the primary heat path and must be soldered (or clipped) to a copper area on the PCB or to a small heatsink. Drain-voltage ringing under 265 V AC operation also demands an RCD snubber sized to the leakage inductance of the flyback transformer.
STSPIN220 - 1/256 Microstep Stepper Driver QFN-16 | STMicroelectronics
The STMicroelectronics STSPIN220 is a low-voltage bipolar stepper motor driver integrating a microstepping sequencer with up to 1/256-step resolution, two PWM current controllers, and a power stage composed of two fully protected full-bridges, housed in a compact 16-pin VFQFPN (3x3x1.0 mm) package. A stepper motor driver is a power management IC that translates low-power control signals into the sequenced phase currents required by bipolar stepper motors. Within the semiconductor hierarchy it sits under motor drivers and motor control ICs, bridging the gap between a microcontroller and the motor coil load. Stepper drivers combine logic (sequencer, translator), current regulation (PWM choppers), and a power stage (H-bridges) in a single device, replacing discrete transistor bridges and simplifying motion-control design. Key features of the STSPIN220 include microstepping resolution as fine as 1/256 of a step for smooth, low-audible-noise motion, an integrated PWM current controller with fixed off-time for accurate coil current regulation, and a low RDS(on) power MOSFET output stage that minimizes conduction losses and heat generation. The device also integrates a full set of protection features, and supports a simple Step/Direction control interface compatible with common 3D-printer and motion-control host architectures. From a technical standpoint, the two fully protected full-bridges drive both phases of a bipolar stepper, while the internal sequencer generates the microstep current profile selected through the microstep mode pins. The PWM current controllers compare the voltage across an external sense element with the reference set by VREF, regulating phase current with fixed off-time chopping. Fully protected operation covers overcurrent and thermal fault conditions, improving system robustness in cost-sensitive designs. Typical applications include 3D printers and 3D-printer stepper driver boards, small robotics and camera-gimbal positioning, laboratory automation, portable battery-powered devices, and low-voltage bipolar stepper actuation up to the 10 V motor-supply class. Its 3x3 mm VFQFPN footprint makes it attractive for space-constrained carrier boards. For design, size the sense resistor so full-scale coil current matches the VREF setting, and provide adequate copper area on the exposed pad for thermal dissipation at higher currents. This page synthesizes distributor pricing, lifecycle information, and application guidance not found in the manufacturer datasheet alone.
STSPIN32F0601TR - 600V 3-Phase BLDC SiP | STM32 | STMicroelectronics
The STMicroelectronics STSPIN32F0601TR is an advanced 600 V three-phase BLDC (brushless DC) motor controller system-in-package (SiP) integrating an ARM Cortex-M0 STM32 microcontroller with 32 KB Flash, a smart gate driver capable of driving N-channel power MOSFETs or IGBTs up to 600 V, and a wide-input linear regulator on a single 64-pin TQFP exposed-pad substrate. Operating from 9 V to 20 V on the supply rail with an embedded 12 V LDO for the gate driver, the device targets home appliances and industrial drives where PCB area, BOM count and reliability dominate the design trade-off. Key headline specs include a 48 MHz Cortex-M0 CPU, 32 KB embedded Flash, 600 V high-voltage rail tolerance on the gate-driver outputs, integrated bootstrap diodes for the three high-side drivers, less than 1 V gate low-level output at 10 mA sink (eliminating external bleeder resistors), an active-low shutdown EN pin, and a smart shutdown comparator that protects the power stage from over-current events. The TQFP-64 10x10 mm package with exposed thermal pad keeps dissipated heat inside the inverter footprint. An LDO (Low-Dropout) linear regulator inside this SiP steps the purpose of a voltage regulator that maintains a stable output even when the input-to-output differential is small; here the 12 V LDO derives the gate-driver VCC from the motor bus, while the MCU core is fed from a separate low-voltage regulator on the same die. The system-in-package concept itself sits within the broader motor-control hierarchy: motor driver IC -> gate driver -> motor controller -> power management IC -> semiconductor. This layered integration is the primary engineering reason designers choose STSPIN32F0601 over a discrete MCU + gate-driver solution. Typical applications include 600 V-class three-phase BLDC/PMSM drives for washing machines, refrigerators, air-conditioner compressors, fans, pumps, industrial servo pumps, and e-bike industrial controllers. The integration also benefits HVAC blower systems and small industrial drives where every millimetre of PCB real estate is at a premium. When laying out the PCB, place the bootstrap capacitors as close as possible to the high-side pins and use a 4-layer board with a continuous ground plane under the exposed pad for thermal relief. Verify that the shunt-resistor value is sized so that the smart-shutdown comparator threshold (200 mV typical on the SD pin) trips before the external MOSFETs exceed their SOA. The SiP is not a hot-swap part; allow at least 1 ms for VCC ramp-up before asserting EN high. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical SiP layout notes that are not found in the manufacturer datasheet, supporting engineers in selecting and qualifying the STSPIN32F0601TR for next-generation high-voltage motor drives.
STSPIN32F0602 - 600V Three-Phase BLDC SiP | STMicroelectronics
The STMicroelectronics STSPIN32F0602 is an advanced 600 V three-phase brushless DC (BLDC) controller system-in-package (SiP) that integrates a high-voltage gate driver with an ARM Cortex-M0 STM32 microcontroller in a single 64-pin TQFP exposed-pad package. The high-voltage rail tolerates up to 600 V and the device pairs with external power switches to build complete three-phase inverters for industrial drives, white goods, and home appliances. A system-in-package for motor control combines an MCU core, gate drivers, and housekeeping supplies in a single molded body, dramatically shrinking PCB footprint and bill-of-material versus a discrete implementation. The STSPIN32F0602 belongs to the broader motor-driver / motor-controller category, which sits hierarchically under power management, motion control, and embedded motor-control ICs; it specifically targets sub-1 kW three-phase BLDC and PMSM applications where integration outweighs the need for separate MCU selection. Key features of the STSPIN32F0602 include three high-voltage/low-voltage gate-driver channels capable of driving N-channel power MOSFETs or IGBTs, an integrated bootstrap diode structure, an embedded STM32F0 Cortex-M0 core, on-chip flash memory, and comprehensive protection including interlocking, deadtime generation, and shutdown on undervoltage. The device is housed in a 64-pin TQFP-EP (10x10 mm) package with an exposed thermal pad that conducts dissipated heat directly to the PCB copper pour, supporting continuous switching at high bus voltages. Architecturally, the SiP isolates the low-voltage digital MCU from the high-voltage analog gate-driver domain, allowing firmware developers to use the standard STM32 toolchain (STM32CubeMX, STM32CubeIDE, ST-LINK) while keeping the analog front end isolated and protected. The gate drivers sink/source sufficient current to switch typical 600 V MOSFETs at tens of kHz, while the integrated bootstrap circuitry eliminates the need for an external bootstrap diode on each high-side channel, reducing BOM count by six discrete components. Typical applications include home appliances such as refrigerator compressors, washing-machine direct-drive motors, and air-conditioner outdoor-unit fans; industrial pumps, fans, and small servo drives; and 600 V-class three-phase inverters where design teams prefer a single qualified IC over a discrete MCU + driver + bootstrap network. The device also suits HVAC blowers and low-power industrial automation drives. When designing with the STSPIN32F0602, ensure the exposed thermal pad is soldered to a sufficient copper area to keep junction temperature within the datasheet limits, and follow the reference schematic in the EVSPIN32F0602S1 evaluation board for the recommended input filter, bulk bus capacitance, and shunt-based current-sensing network. Programming requires an SWD interface; the device is supported by the standard STM32Cube ecosystem, allowing firmware reuse across the STSPIN32 family. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. As of 2026-10-10, the STSPIN32F0602 is broadly stocked at distributors including DigiKey, Mouser, and the ST eStore, with pricing in the typical industrial SiP range.
STUSB1702YQTR - USB Type-C PD Controller with TX/RX Line Driver | STMicroelectronics
The STMicroelectronics STUSB1702YQTR is a USB Type-C port controller with integrated TX/RX line driver and BMC (Biphase Mark Coding) transceiver, qualified to AEC-Q100 and supplied in a 24-pin QFN EP (4x4 mm wettable flanks) package. It implements a USB Type-C source controller with VBUS power switch, dead-battery support, and USB Power Delivery (PD) message handling for USB 2.0 and SuperSpeed USB 3.0 signaling paths. The device operates over a supply range of 4.1 V to 22 V with a -40 C to +105 C operating temperature window, and the wettable-flank QFN-24 (QFN24 EP 4x4 mm) package enables automated optical inspection for automotive applications. Key features include USB Type-C cable attach and orientation detection (CC1/CC2 logic), USB PD 2.0 / 3.0 protocol layer with PHY, integrated VBUS source path regulation, I2C host interface for policy management, hardware GPIO for status indication, and built-in support for Source role power negotiation. The wettable-flank QFN package removes the need for X-ray inspection post-soldering, lowering manufacturing cost in AEC-Q100 environments. The STUSB1702 is part of the STUSB1700 family of Type-C port controllers. Within the family, STUSB1700/1700Y denote cable orientation-only devices, while the STUSB1702Y integrates the TX/RX line driver and BMC block required to actively negotiate USB Power Delivery contracts. Designers select STUSB1702Y when they need full USB PD message transport rather than only attach/orientation signaling. Typical applications include automotive USB Type-C charging ports, in-vehicle infotainment head units, USB-PD wall adapters, mobile docking stations, USB Type-C monitors, and industrial USB Type-C breakout modules. The integrated VBUS switch and source power role make it a single-chip solution for provider-only (Source) PD ports. When designing with this device, plan VBUS bulk capacitance per the USB PD spec and verify that the upstream Type-C connector CC1/CC2 pinout routes match the datasheet reference. The 22 V abs-max VBUS tolerance means automotive load-dump and USB-PD Extended Power Range (EPR) applications are both supported with appropriate TVS protection.
STUSB4531QTR - USB PD Sink Controller I2C QFN-16 | ST
The STMicroelectronics STUSB4531QTR is a standalone USB Type-C Power Delivery (PD) sink controller with an I2C interface, housed in a 16-pin QFN (3x3 mm) package. It negotiates up to five configurable Power Data Objects (PDOs) supporting 5V, 9V, 12V, 15V and 18V sink profiles, and operates without any external microcontroller firmware thanks to a PDO configuration stored in internal non-volatile memory. A USB PD sink controller is a power management interface IC that implements the USB Type-C connector attach/detect state machine and the USB PD protocol on the CC (Configuration Channel) pins, allowing a powered device to request higher voltages and currents from a PD source. It sits in the system hierarchy between the physical USB-C receptacle and the downstream DC-DC converter or battery charger, translating the negotiated contract into VBUS connect/disconnect control and voltage selection signals. Key features of the STUSB4531 include fully autonomous negotiation (autorun mode) that requires no software support, making it ideal for automatic high-power profile charging; a hybrid mode that allows an embedded host to override or monitor negotiation via the I2C interface; and always-on dead battery mode, which presents CC pull-down terminations even when the device is unpowered, so a fully depleted battery (SOC = 0%) can still be charged directly from the VBUS receptacle pins. Technically, the STUSB4531 integrates the CC line termination logic, BMC transceivers, PD protocol engine, and NVM-based configuration in a single die. VBUS_EN_SNK provides the sink VBUS power-path enable output, and the GATE pin supports external NMOS VBUS switch control. The I2C interface exposes status registers, alert interrupts, and allows runtime PDO modification without reprogramming the NVM. Typical applications include USB-C powered monitors, docks and hubs, battery-powered consumer devices requiring dead-battery charging, industrial equipment with USB-C power inputs, and any sink-only system that needs PD negotiation without a firmware investment. Designers should note that dead battery mode is always active on the QTR and BJR variants, ensuring source attach even with zero system power. A key design consideration is that the device is powered directly from VBUS through the VDD pin, so layout should keep the VBUS sense and CC traces short and matched, and the VBUS_EN_SNK pin can be left unconnected if the power path is controlled elsewhere while negotiation still proceeds over CC. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Si8271GB-ISR - 4A Isolated Gate Driver, 2.5kV, 8-SOIC | Skyworks
The Skyworks Solutions Si8271GB-ISR is a 4 A galvanically-isolated single-channel gate driver with 2.5 kV RMS withstand voltage, housed in a narrow-body 8-pin SOIC (SO-8) package. It delivers 4 A peak source/sink drive current with a typical propagation delay of 50 ns and high CMTI of 400 kV/µs for switching power MOSFETs, IGBTs, and SiC/GaN HEMTs. An isolated gate driver is a galvanic isolation barrier combined with a high-current buffer stage, used to drive the gate of a high-side or low-side power transistor while protecting low-voltage control logic from high-voltage transients. The isolated gate driver category sits within the power management hierarchy: gate driver -> driver IC -> power management IC -> semiconductor. Si827x-family parts use proprietary silicon-oxide isolation instead of optocouplers or transformers, which eliminates LED-aging concerns and provides tight timing characteristics. Key features include 4 A peak output current, 30 ns typical propagation delay, 400 kV/µs common-mode transient immunity (CMTI), 2.5 kV RMS isolation per UL1577, integrated UVLO with 3 V threshold for IGBT/SiC protection, de-glitch input filtering, and a programmable dead-time (DT) pin. The narrow-body 8-SOIC footprint is pin-compatible with common opto-isolated gate drivers, enabling direct PCB replacement in many designs. The device uses Skyworks' proprietary silicon isolation technology based on RF-coupled differential transmission across a high-voltage silicon-oxide barrier. This approach eliminates the lifetime and CTR degradation inherent in optocouplers, and avoids the high-frequency emissions and large footprint of pulse transformers. The driver outputs swing rail-to-rail from VDD to GND on each side, supporting both +12 V and unipolar gate-drive rails. Typical applications include driving IGBTs in motor-control inverters, SiC MOSFETs in EV traction and onboard chargers, GaN HEMTs in telecom DC-DC bricks, solar inverters, industrial SMPS half-bridge stages, and digital-isolation upgrades for opto-coupler-based legacy designs. The wide driver supply range supports both 5 V and 12/15 V gate-drive rails. When designing with this part, place a 100 nF decoupling capacitor close to each VDD pin and a 4.7 µF bulk capacitor on the output-side VDD. For half-bridge use, the programmable dead-time pin prevents shoot-through; consult the manufacturer datasheet for the DT resistor selection table.
TAS5110DAPR - 50W Stereo Class D Amplifier | Texas Instruments
The Texas Instruments TAS5110DAPR is a 2-channel stereo Class D digital audio power amplifier designed for 50 W per channel into a 6 ohm load at 10% THD. It is a true digital audio amplifier power stage using TI Equibit technology and is packaged in a 32-pin HTSSOP. The device delivers 40 W per channel at 0.1% THD, with typical THD+N below 0.09% for a 1 kHz input signal and a dynamic range of 93 dB in the TDAA system. A Class D audio amplifier is a switching power amplifier that uses pulse-width modulation to represent an audio waveform. Unlike a conventional linear amplifier, its output transistors operate mainly in the saturated and unsaturated states, reducing dissipation and improving power efficiency. The TAS5110 belongs to the digital power-stage hierarchy and requires a compatible digital audio PWM processor to supply its command inputs. It is therefore positioned as the output stage of a true digital audio system rather than as a conventional analog-input amplifier. The principal performance figures cover continuous power, distortion, and signal-to-noise behavior. Output power reaches 50 W per channel into 6 ohms at 10% THD, while the lower-distortion figure is 40 W per channel at 0.1% THD. Typical THD+N is less than 0.09% with a 1 kHz input signal, and system dynamic range is 93 dB. The stereo architecture supports two independent audio channels in one package, reducing the number of power-stage ICs needed in a multichannel amplifier architecture. The device uses TI's Equibit technology as part of a true digital audio signal path. Digital command signals drive the internal PWM power stage, reducing sensitivity to analog input-stage distortion and supporting coordinated power management across multiple channels. Integrated short-circuit and thermal protection, mute control, shutdown control, and multiple digital inputs provide the basic controls needed for a robust amplifier module. Exact clock, control-voltage, and timing details should be taken from the manufacturer pin-description and timing tables before PCB implementation. Typical applications include powered speakers, home-theater and multimedia amplification, professional audio equipment, soundbars, and compact stereo systems requiring high output power from a surface-mount package. The 50 W per-channel capability is most useful with low-impedance speakers, while the 40 W rating at 0.1% THD provides a more conservative operating point for designs that prioritize low distortion. Pairing the device with a suitable TAS50xx digital audio processor enables direct digital command and system-level control. A critical layout consideration is the power stage's high-current switching output. The HTSSOP exposed thermal pad must be connected to a properly designed copper area and thermal path, while output-filter and speaker traces must be kept away from sensitive control and clock routes. Supply capacitors must be placed close to the power pins, and the manufacturer reference layout should be followed to control switching noise, voltage drops, and thermal performance. This page combines the manufacturer's core power and distortion ratings with package information, application guidance, design notes, and a conservative assessment of drop-in replacement options. It is intended to help engineers plan the power budget, thermal strategy, PCB footprint, digital audio interface, and speaker load before releasing a TAS5110DAPR-based design for production.
TAS5122DCA - 50W Stereo Class-D Power Stage | TI
Texas Instruments TAS5122DCA is a 50 W stereo PWM-input Class-D audio power amplifier with a 0 V to 25.5 V supply range, housed in a 56-pin HTSSOP DCA package. The integrated stereo output stage is designed to drive 6-ohm speakers at up to 30 W per channel while accepting PWM signals from a compatible digital audio processor. A Class-D audio power amplifier is an efficient switching amplifier that uses pulse-width-modulated signals to drive a passive loudspeaker through a demodulation filter. The TAS5122DCA belongs to the digital audio amplifier hierarchy: Class-D amplifier, integrated stereo power stage, audio amplifier IC, and power-management semiconductor. Unlike an analog input amplifier, it does not directly accept a conventional audio waveform; it requires PWM-compatible digital audio signaling. Key features include two-channel stereo operation, a 50 W stereo power rating, PWM signal compatibility, and TI PurePath Digital technology. The device is intended for use with a TAS50XX-family digital audio PWM processor and a passive output filter. Its DC-coupled speaker output architecture supports efficient conversion of digital audio power into analog speaker drive without requiring a traditional analog power-output stage. The architecture separates digital signal generation from analog power amplification. A compatible audio processor generates the PWM waveform, while the TAS5122DCA performs the high-current switching function and drives the speaker network. This division allows system designers to use a digital signal-processing path for decoding, volume control, channel mixing, and protection while retaining efficient Class-D output-stage behavior. Typical applications include DVD receivers, home-theater systems, mini and micro component systems, and internet music appliances. These products benefit from compact digital audio processing, efficient speaker drive, and a direct connection between a PWM audio processor and the integrated stereo power stage. A passive LC demodulation filter is used between the amplifier outputs and the loudspeakers to recover the audio waveform. Power-supply design must accommodate the amplifier's stated 0 V to 25.5 V supply range and provide sufficient current for the intended speaker load. The HTSSOP package includes a thermal pad for heat dissipation, making copper-area and thermal via placement important on multilayer printed circuit boards. Stable operation also depends on correct output-filter selection and proper decoupling of the power rails. This page combines the manufacturer's device description, package and application details, drop-in alternatives, comparison information, and practical layout guidance. It helps engineers identify the TAS5122DCA for efficient digital speaker amplification while separating known device characteristics from parameters that require confirmation against the latest manufacturer documentation.
TAS5122DCAR - 50W Stereo Class-D Power Stage | TI (Tape & Reel)
Texas Instruments TAS5122DCAR is a 50 W stereo PWM-input Class-D audio power amplifier with a 0 V to 25.5 V supply range, housed in a 56-pin HTSSOP DCA package. The integrated stereo output stage is designed to drive 6-ohm speakers at up to 30 W per channel while accepting PWM signals from a compatible digital audio processor. A Class-D audio power amplifier is an efficient switching amplifier that uses pulse-width-modulated signals to drive a passive loudspeaker through a demodulation filter. The TAS5122DCAR belongs to the digital audio amplifier hierarchy: Class-D amplifier, integrated stereo power stage, audio amplifier IC, and power-management semiconductor. Unlike an analog input amplifier, it does not directly accept a conventional audio waveform; it requires PWM-compatible digital audio signaling. Key features include two-channel stereo operation, a 50 W stereo power rating, PWM signal compatibility, and TI PurePath Digital technology. The device is intended for use with a TAS50XX-family digital audio PWM processor and a passive output filter. Its DC-coupled speaker output architecture supports efficient conversion of digital audio power into analog speaker drive without requiring a traditional analog power-output stage. The architecture separates digital signal generation from analog power amplification. A compatible audio processor generates the PWM waveform, while the TAS5122DCAR performs the high-current switching function and drives the speaker network. This division allows system designers to use a digital signal-processing path for decoding, volume control, channel mixing, and protection while retaining efficient Class-D output-stage behavior. Typical applications include DVD receivers, home-theater systems, mini and micro component systems, and internet music appliances. These products benefit from compact digital audio processing, efficient speaker drive, and a direct connection between a PWM audio processor and the integrated stereo power stage. A passive LC demodulation filter is used between the amplifier outputs and the loudspeakers to recover the audio waveform. Power-supply design must accommodate the amplifier's stated 0 V to 25.5 V supply range and provide sufficient current for the intended speaker load. The HTSSOP package includes a thermal pad for heat dissipation, making copper-area and thermal via placement important on multilayer printed circuit boards. Stable operation also depends on correct output-filter selection and proper decoupling of the power rails. This page combines the manufacturer's device description, package and application details, drop-in alternatives, comparison information, and practical layout guidance. It helps engineers identify the TAS5122DCAR for efficient digital speaker amplification while separating known device characteristics from parameters that require confirmation against the latest manufacturer documentation.