AD9226ARSRL - 12-Bit 65 MSPS ADC | Analog Devices
MPN: AD9226ARSRL ✓ چالاکAD9226ARSRL گشتی
An ADC is a semiconductor that converts continuous analog voltage into a digital representation for processing, storage, or transmission. The AD9226 belongs to the pipelined ADC hierarchy, where multiple internal stages perform successive approximation functions. The resulting 12-bit parallel interface transfers each converted sample directly to digital logic, making the device suitable for data-acquisition systems that require deterministic throughput and broad bandwidth.
Key characteristics include 12-bit resolution, a maximum sampling rate of 65 MSPS, and 11.1-bit ENOB at a 10 MHz input frequency. The converter's differential pipeline architecture supports input frequencies beyond the sampling clock because its analog front end has 750 MHz full-power bandwidth. Straight binary and two's-complement output formats provide flexibility when interfacing with FPGAs, DSPs, microprocessors, or data-capture logic.
The on-chip sample-and-hold amplifier minimizes the number of external high-frequency analog components, while the internal voltage reference simplifies calibration and board design. A single 5 V analog supply reduces supply complexity compared with dual-supply converter designs. Logic supply voltage can be selected to match 3 V or 5 V digital systems, although the exact clock, timing, and output-valid details should be taken from the manufacturer datasheet before finalizing an interface.
Typical uses include communications receivers, industrial data acquisition, RF and IF signal sampling, digital oscilloscopes, control instrumentation, and diagnostic monitoring. The 65 MSPS rate supports a 32.5 MHz Nyquist zone, while 750 MHz full-power bandwidth is valuable when downconversion or direct RF sampling is required. System designers must still account for analog bandwidth, clock jitter, output timing, grounding, decoupling, and FPGA timing closure.
For a new design, place the analog input and clock paths on a controlled-impedance board, keep the ADC and its decoupling close together, and provide a low-noise, stable supply. Use the manufacturer's evaluation-board layout and datasheet timing diagrams as the primary implementation references. This page combines verified source data, practical application guidance, and honestly qualified drop-in alternatives for AD9226ARSRL.
جێگرەوەکانی جێگۆڕکێ بۆ AD9226ARSRL — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AD9226ARSRL (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Architecture, Data Interface, Intermodulation Distortion, Package.
AD9223
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD9225
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD9226ARSRL زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| وردی | 12 bit |
| ڕێژەی نموونەگرتن | 65 MSPS |
| Architecture | Multistage differential pipeline |
| Number of Inputs | 1 input |
| Input Type | Differential |
| Data Interface | Parallel CMOS |
| Full-Power Bandwidth | 750 MHz |
| ENOB | 11.1 bit at 10 MHz input |
| Intermodulation Distortion | -75 dBFS at 140 MHz input |
| Analog Supply | 5 V |
| Driver Supply | 3 V or 5 V |
| Output Formats | Straight binary or two's complement |
| Sample-and-Hold Amplifier | On chip |
| Voltage Reference | On chip |
| پاکێج | 28-lead SSOP, 5.30 mm width |
ڕێنمایی ڕێکخستنی پینی AD9226ARSRL 28-lead ssop, 5.30 mm width
ڕێکخستنی پین بۆ AD9226ARSRL (پاکێجی 28-lead ssop, 5.30 mm width). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD9226ARSRL.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
AD9226ARSRL گونجاوە بۆ 6 بەکارھێنانs: Communications Receiver Signal Capture, Digital Oscilloscope Front End, Industrial Data Acquisition, RF and IF Direct Sampling, Precision Control Instrumentation, Diagnostic and Monitoring Equipment.
Communications Receiver Signal Capture
The AD9226ARSRL fits communications receivers that require a 12-bit parallel ADC operating at 65 MSPS. Its 750 MHz full-power bandwidth allows the analog input to cover frequencies beyond the 32.5 MHz Nyquist frequency of the sampling rate, which is useful for IF sampling when a suitable local oscillator and anti-alias filter are used. The single 5 V analog supply and selectable 3 V or 5 V driver supply simplify implementation with FPGA capture logic, while straight binary and two's-complement output options support different downstream formats. Clock jitter, input return loss, and adjacent-channel filtering must be evaluated against the receiver's modulation and error-budget requirements.
پێشنیارکراو
Digital Oscilloscope Front End
The AD9226ARSRL can serve as the acquisition converter in a high-speed digital oscilloscope or laboratory data-acquisition instrument. A 65 MSPS sampling rate supplies 32.5 MHz nominal Nyquist bandwidth, while the 750 MHz full-power bandwidth allows useful front-end design flexibility for higher-bandwidth acquisition paths. The 12-bit parallel output avoids serial-interface overhead and can feed an FPGA that performs triggering, interpolation, filtering, and display processing. Analog gain, source termination, anti-alias filtering, clock generation, and memory timing determine whether the nominal converter performance is preserved in a practical instrument.
پێشنیارکراو
Industrial Data Acquisition
The AD9226ARSRL is suitable for industrial acquisition systems that sample rapidly changing sensor, transducer, or test signals into digital logic. Its 65 MSPS throughput provides a practical balance between 12-bit data resolution and direct parallel capture, while the 750 MHz analog bandwidth supports front-end bandwidth beyond the converter's nominal Nyquist zone. The on-chip sample-and-hold amplifier and voltage reference reduce the number of external precision components, while the single 5 V analog supply simplifies isolated or embedded data-acquisition hardware. Engineers should still budget for channel protection, anti-alias filters, gain calibration, clock jitter, and FPGA or processor memory bandwidth.
پێشنیارکراو
RF and IF Direct Sampling
The AD9226ARSRL is suitable for RF or intermediate-frequency sampling when the converter's 750 MHz full-power bandwidth is required. Sampling at 65 MSPS supports band-limited signal capture beyond 32.5 MHz, provided that the analog front end has suitable gain, filtering, impedance matching, and frequency-flattening. The parallel CMOS interface allows captured samples to be processed rapidly by FPGA logic for demodulation, spectrum analysis, or interference detection. Practical performance is often limited by clock phase noise, source impedance, reference behavior, and PCB transmission-line discontinuities rather than by the converter's nominal sample rate alone.
پێشنیارکراو
Precision Control Instrumentation
The AD9226ARSRL can be used in control, instrumentation, and embedded measurement systems that require fast conversion and a parallel digital interface. The 12-bit nominal resolution provides 4,096 possible code levels, and the reported 11.1-bit ENOB at 10 MHz gives a more realistic indication of usable dynamic performance. The 65 MSPS conversion rate supports real-time sampling of rapidly changing feedback signals, while the single 5 V analog supply and 3 V or 5 V driver options simplify mixed-voltage integration. Calibration should include reference, gain, offset, input bandwidth, clock, and temperature effects rather than relying solely on nominal resolution.
پێشنیارکراو
Diagnostic and Monitoring Equipment
The AD9226ARSRL is applicable to diagnostic and monitoring equipment that captures short-duration waveforms or rapidly changing sensor outputs. Its 65 MSPS rate permits dense temporal sampling, and the parallel output can feed a processor or FPGA for event detection, filtering, and feature extraction. The internal voltage reference and sample-and-hold amplifier reduce external component count, which is useful in compact monitoring equipment. For medical or safety-related uses, the broader signal chain, isolation, patient protection, calibration method, and total measurement uncertainty remain system-level responsibilities; the converter's 12-bit nominal resolution should not be treated as complete instrument accuracy.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ AD9226ARSRL — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | AD9223 | AD9225 |
|---|---|---|---|
| Package | 28-lead SSOP | 28-lead SSOP | 28-lead SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Sampling Rate | 65 MSPS | 65 MSPS | 65 MSPS |
جیاکەرەوە سەرەکییەکان
- High analog bandwidth relative to conversion rate (بەراورد بەAD9225)
- Compact parallel conversion throughput (بەراورد بەAD9223)
- Simplified analog and digital supply arrangement (بەراورد بەAD9225)
تێبینییەکانی دیزاین
Treat the analog input as a controlled-impedance RF signal path rather than a conventional low-frequency measurement input. Place input termination, anti-alias filtering, and any gain stage close to the ADC; avoid stubs and unprotected long traces; and provide a continuous return path beneath the input route. The verified 750 MHz full-power bandwidth makes trace geometry, connector transitions, and component parasitics materially more important than they would be in a low-bandwidth instrumentation design.
Use the manufacturer reference schematic for analog and digital supply separation, decoupling values, and power sequencing. The AD9226ARSRL uses a single 5 V analog supply and supports 3 V or 5 V driver supplies. Keep high-current return paths compact, connect supply and ground planes with low-inductance vias, and avoid sharing narrow neck geometries between the analog converter and digital output-driver domain. Exact capacitor values and current limits are not present in the supplied excerpts and must be taken from the manufacturer datasheet.
The 65 MSPS sampling edge must be delivered with low timing uncertainty because clock phase noise reduces conversion performance, especially near the 750 MHz analog-bandwidth limit. Use a low-jitter clock source, route the clock as a controlled-impedance signal, provide a defined return path, and match data-output timing to the receiving FPGA or processor. Confirm output delay, data-valid timing, and setup/hold margins using the relevant Analog Devices datasheet revision rather than general timing assumptions.
Do not equate 65 MSPS sampling with 65 MHz of usable flat input bandwidth, and do not infer full accuracy from the nominal 12-bit resolution. The converter reports 11.1-bit ENOB at 10 MHz, while its 750 MHz full-power bandwidth describes a different analog characteristic. Input gain, bandwidth, anti-alias filtering, source impedance, clock quality, reference stability, PCB return paths, and digital capture timing jointly determine system performance. Validate the complete chain with the manufacturer's evaluation hardware and calibrated test equipment.
زانیاری پابەندبوون
The supplied verified excerpts do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because the AD9226ARSRL is an industrial analog-to-digital converter rather than an automotive-qualified device.