Analog Devices

ADF4355-3BCPZ - 6.6 GHz Fractional-N PLL | Analog Devices

MPN: ADF4355-3BCPZ ✓ چالاک
3.15 V to 3.45 V Vdss 32-lead WFQFN with exposed pad Package 6.6 GHz Speed
MOQ: 1 |

ADF4355-3BCPZ گشتی

The Analog Devices ADF4355-3BCPZ is a fractional-N and integer-N phase-locked loop frequency synthesizer with an integrated voltage-controlled oscillator, a 6.6 GHz RF output capability, and programmable output power. It is packaged in a 32-lead WFQFN exposed-pad surface-mount package for compact RF and microwave designs.

An integrated wide-band VCO allows the ADF4355-3 to generate frequencies from approximately 35 MHz to 6.6 GHz using fractional-N or integer-N synthesis. Its RF output supports programmable power levels, while output dividers provide flexible frequency generation for receiver and transmitter signal chains. An external reference clock and loop filter are required for normal closed-loop operation.

The device uses separate analog and digital power rails operating from 3.15 V to 3.45 V. Charge-pump and VCO power rails accept 4.75 V to 5.25 V, allowing the RF section to operate with a higher supply while digital control logic remains on a 3.3 V rail. Both hardware and software power-down modes are available for shutdown and duty-cycle control.

The ADF4355-3BCPZ is designed for frequency-agile communication equipment, wireless infrastructure, microwave radios, test and measurement instruments, and phased-array or clock-generation subsystems. Its programmable output power helps optimize the link budget when the downstream mixer, power amplifier, or receiver does not require maximum drive.

Designers must account for the exposed thermal pad when laying out the PCB. The package ground connection and exposed pad should be tied to a low-impedance ground plane with adequate via density, and the loop filter should be positioned close to the charge-pump pins. The operating temperature range is -40°C to +105°C, covering industrial and extended-temperature environments.

جێگرەوەکانی جێگۆڕکێ بۆ ADF4355-3BCPZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADF4355-3BCPZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Device Type, Maximum RF Output Frequency, Analog and Digital Supply Voltage, Charge Pump and VCO Supply Voltage.

Analog Devices
Package: 32-pin WFQFN with exposed pad
Device Type: Fractional-N and integer-N RF frequency synthesizer
Maximum RF Output Frequency: 4400 MHz
بەراوردکردن لەگەڵ ADF4355-3BCPZ →
Analog Devices
Package: 32-WFQFN exposed-pad CSP
Device Type: Fractional-N or integer-N RF clock/frequency synthesizer with integrated VCO
Maximum RF Output Frequency: 6800 MHz
بەراوردکردن لەگەڵ ADF4355-3BCPZ →
Analog Devices
Analog and Digital Supply Voltage: 3.3 V
Charge Pump and VCO Supply Voltage: 5.0 V typical
بەراوردکردن لەگەڵ ADF4355-3BCPZ →

ADF4355BCPZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 32-lead WFQFN with exposed pad
Fractional-N or integer-N RF clock/frequency synthesizer with integrated VCO · 54 MHz to 6800 MHz · 6800 MHz · 54 MHz · 38 bit · 1, 2, 4, 8, 16, 32, or 64 · 1.8 V · 3.3 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADF4355-3BCPZ-RL7

✅ جێگرەوەی ڕاستەوخۆ
📦 32-lead WFQFN with exposed pad
Same ADF4355-3 device and 32-lead package construction, differing primarily in reel or order-code designation.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADF4355-3BCPZ تایبەتمەندییەکان

Device Type Phase-locked loop frequency synthesizer with integrated VCO
Synthesis Modes Fractional-N and integer-N
Maximum RF Output Frequency 6.6 GHz
Analog and Digital Supply Voltage 3.15 V to 3.45 V
Charge Pump and VCO Supply Voltage 4.75 V to 5.25 V
پاکێج 32-lead WFQFN with exposed pad
Output Power Programmable
Output Dividers Series of RF output frequency dividers
Loop Filter External
Reference Input External reference frequency required
Power-Down Modes Hardware and software
مەودای پلەی گەرمیی کارکردن -40°C to +105°C
جۆری دامەزراندن Surface mount
ژمارەی پینەکان 32
Exposed Thermal Pad Yes

ڕێنمایی ڕێکخستنی پینی ADF4355-3BCPZ 32-lead wfqfn with exposed pad

ڕێکخستنی پین بۆ ADF4355-3BCPZ (پاکێجی 32-lead wfqfn with exposed pad). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 32-lead wfqfn with exposed pad بۆ ADF4355-3BCPZ

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADF4355-3BCPZ.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADF4355-3BCPZ گونجاوە بۆ 6 بەکارھێنانs: Wireless Transmitter Local Oscillator, Microwave Receiver Frequency Source, RF Signal Source and Test Equipment, Clock Generation for Communication Modules, Satellite and Phased-Array Frequency Generation, Duty-Cycled Industrial RF Modules.

🌐

Wireless Transmitter Local Oscillator

The ADF4355-3BCPZ fits a programmable local-oscillator or frequency-synthesis role in wireless transmitters because it supports fractional-N and integer-N operation up to 6.6 GHz. An external reference and loop filter establish the closed loop, while the programmable output power lets the designer match the drive level to a mixer or power-amplifier input. Separate 3.3 V control and 4.75 V to 5.25 V charge-pump/VCO rails also simplify partitioning between digital and RF supply networks.

📡

Microwave Receiver Frequency Source

In a microwave receiver, the ADF4355-3BCPZ can generate a tunable local oscillator for a receiver front end operating below its 6.6 GHz maximum output frequency. The output dividers support multiple frequency relationships, and programmable RF output power can reduce the drive applied to a mixer or low-noise amplifier. Place the loop filter near the charge-pump pins and isolate the reference and RF paths to preserve phase-noise performance.

🖥️

RF Signal Source and Test Equipment

The ADF4355-3BCPZ is useful in compact RF signal sources, sweepers, and bench-test instruments where a programmable frequency is required without a separate VCO assembly. Its integrated VCO reduces the number of discrete frequency-generation components, while fractional-N operation permits fine channel spacing relative to the reference. Programmable output power supports repeatable measurements across multiple DUT drive levels, and the -40°C to +105°C rating supports extended-temperature industrial equipment.

💻

Clock Generation for Communication Modules

The ADF4355-3BCPZ can provide a programmable reference or intermediate frequency for communication modules that need a compact, synthesizer-based clock source. Its output dividers allow the reference relationship to be adapted without changing the overall PLL architecture, and the hardware power-down function supports controlled operating intervals. The 32-lead exposed-pad package is suitable for dense RF boards, provided the thermal pad is connected to a low-impedance ground plane.

✈️

Satellite and Phased-Array Frequency Generation

The ADF4355-3BCPZ can supply an individually programmable RF tone for phased-array and satellite communication subsystems operating within its 6.6 GHz capability. Fractional-N synthesis allows closely spaced channels to be programmed, while integer-N operation simplifies applications with exact divider ratios. Keep the exposed pad thermally connected and route the reference clock away from high-level RF outputs to minimize crosstalk between adjacent channels.

🏭

Duty-Cycled Industrial RF Modules

The ADF4355-3BCPZ is appropriate for industrial RF modules that periodically transmit and can benefit from hardware or software power-down. Disabling the synthesizer between bursts can reduce energy consumption and radiated activity. Its extended -40°C to +105°C operating range supports factory, transportation, and outdoor-adjacent equipment, while the separated analog, digital, and RF supply domains permit regulated local rails with targeted filtering.

کورتەی بەرهەمە پێشنیارکراوەکان

ADF4355BCPZ Analog Devices بەکارهێنراوە لە: Wireless Transmitter Local Oscillator, Microwave Receiver Frequency Source, Clock Generation for Communication Modules, Satellite and Phased-Array Frequency Generation ADF4355-3BCPZ-RL7 Same ADF4355-3 configuration for equivalent signal-source designs بەکارهێنراوە لە: RF Signal Source and Test Equipment, Duty-Cycled Industrial RF Modules
What is the ADF4355-3BCPZ used for?
The ADF4355-3BCPZ is used as a fractional-N or integer-N phase-locked loop frequency synthesizer with an integrated voltage-controlled oscillator. According to the Analog Devices ADF4355-3 product information, it supports generation up to 6.6 GHz and requires an external reference clock and external loop filter. Typical uses include RF signal sources, wireless test equipment, microwave receivers, and programmable local oscillators.
What is the maximum output frequency of the ADF4355-3BCPZ?
The maximum RF output frequency of the ADF4355-3BCPZ is 6.6 GHz. The DigiKey component listing identifies the part as a 6.6 GHz clock/frequency synthesizer, and the Analog Devices ADF4355-3 family page confirms the integrated-VCO PLL architecture. An external loop filter and reference frequency are used to complete the closed-loop synthesizer implementation.
What supply voltages does the ADF4355-3BCPZ require?
The ADF4355-3BCPZ requires 3.15 V to 3.45 V for the analog and digital supplies and 4.75 V to 5.25 V for the charge-pump and VCO supplies. The Analog Devices product information states these supply ranges explicitly. Separate rails allow the RF circuitry to use the higher voltage while the digital control section operates from a 3.3 V rail.
Does the ADF4355-3BCPZ need an external loop filter and reference?
Yes, the ADF4355-3BCPZ requires an external loop filter and an external reference frequency. The Analog Devices ADF4355-3 family page identifies both as part of a working fractional-N or integer-N synthesizer implementation. Keep the loop-filter components close to the charge-pump pins, and route the reference input away from high-level RF outputs to reduce coupling.
Can the ADF4355-3BCPZ generate fractional-N frequencies?
The ADF4355-3BCPZ supports both fractional-N and integer-N frequency synthesis. The Analog Devices product information explicitly lists fractional-N and integer-N operating modes. Fractional-N operation permits a fine frequency step relative to the reference spacing, while integer-N mode provides a simple divider-based relationship between the reference and output frequencies.
Is the output power of the ADF4355-3BCPZ adjustable?
Yes, the ADF4355-3BCPZ provides a programmable output power level. This makes it possible to reduce RF drive toward a downstream mixer, receiver, or power amplifier when the full output level is unnecessary. The datasheet documentation describes programmable output power, while the frequency divider options provide additional control over the generated RF output.
What is the difference between ADF4355-3BCPZ and ADF4355BCPZ?
The ADF4355-3BCPZ and ADF4355BCPZ share the same 32-lead LFCSP package, pinout, and 3.3 V supply architecture. Their principal reported distinction is the maximum RF output frequency, with the ADF4355-3BCPZ specified to 6.6 GHz. Because the frequency ranges differ, verify the highest required channel frequency and the associated RF output settings before treating either device as a substitute.
What is the best drop-in replacement for the ADF4355-3BCPZ?
The closest same-family replacement candidate is the ADF4355BCPZ because it uses the same 32-lead package and pinout. The key qualification is its lower maximum RF output frequency relative to the ADF4355-3BCPZ. For a 6.6 GHz design, retain the original part; for lower-frequency operation, confirm the required register settings, output range, and supply conditions before substitution.
Is ADF4355BCPZ the same as ADF4355-3BCPZ?
No, they are closely related but not frequency-equivalent devices. The ADF4355BCPZ and ADF4355-3BCPZ share a 32-lead package and pin arrangement, but the ADF4355-3BCPZ supports a higher maximum RF output frequency of 6.6 GHz. Package compatibility alone is therefore insufficient for designs that operate near the upper frequency limit.
When should I choose the ADF4355-3BCPZ over the ADF4355BCPZ?
Choose the ADF4355-3BCPZ when the design must generate RF frequencies above the range supported by the ADF4355BCPZ or needs the 6.6 GHz capability of the -3 variant. Choose the ADF4355BCPZ for lower-frequency designs that accept its reduced maximum output frequency and share the same 32-lead footprint. Verify locking range and register behavior for the exact mode of operation.
Where can I download the ADF4355-3BCPZ datasheet PDF?
The official ADF4355-3 datasheet is available through the Analog Devices product page at https://www.analog.com/en/products/adf4355-3.html. A separate 35-page ADF4355-3BCPZ datasheet PDF is also indexed through the All Datasheet listing. Use the Analog Devices document for authoritative supply, register, electrical, and package information before releasing a production design.
Where can I find the ADF4355-3BCPZ pinout?
The ADF4355-3BCPZ pinout is documented in the manufacturer datasheet, which covers the 32-lead WFQFN exposed-pad package and its ground, supply, reference, control, and RF connections. The package uses 32 leads plus an exposed thermal pad. Use the pin-description table and land-pattern guidance in the Analog Devices datasheet when assigning PCB tracks.
What power-down options are available on the ADF4355-3BCPZ?
The ADF4355-3BCPZ provides both hardware and software power-down modes. The Analog Devices product information identifies both modes explicitly. Hardware power-down supports an external control signal, while software power-down is controlled through the device interface. These functions are useful for duty-cycled RF systems that need to reduce supply consumption between operating intervals.
What is the operating temperature range of the ADF4355-3BCPZ?
The ADF4355-3BCPZ is specified for an operating temperature range of -40°C to +105°C. The LCSC product listing states this temperature range for the device. In designs approaching the upper limit, pay particular attention to exposed-pad heat removal, supply regulation, and the temperature coefficient of the crystal or external reference.
Where can I buy the ADF4355-3BCPZ online?
The ADF4355-3BCPZ can be sourced through authorized component distributors, with current availability and commercial terms changing over time. Use the Request a Quote form on this page to request a current quotation, lot availability, and lead time. The listing also provides the official manufacturer datasheet for engineering review before procurement.
How much does the ADF4355-3BCPZ cost?
The current commercial price of the ADF4355-3BCPZ depends on quantity, date, and distributor inventory. Use the Request a Quote form on this page for a current unit-price and volume-break response. For design budgeting, confirm the price, stock position, and lead time at the time of purchase because component pricing changes frequently.
Is the ADF4355-3BCPZ currently in stock?
Inventory for the ADF4355-3BCPZ fluctuates by region, quantity, and supplier. Use the Request a Quote form on this page to request the current stock status, scheduled delivery, and minimum order quantity. Provide your target quantity and required date so the quotation can reflect the appropriate supply channel.
What is the lead time for the ADF4355-3BCPZ?
The current lead time for the ADF4355-3BCPZ depends on the order quantity and the supply channel selected. Use the Request a Quote form on this page to request a dated lead-time confirmation along with stock and minimum-order-quantity details. For production planning, include buffer time for any required PCB rework or schedule changes.
What are the key specifications of the ADF4355-3BCPZ?
The key specifications of the ADF4355-3BCPZ include a 6.6 GHz maximum RF output, fractional-N and integer-N synthesis, programmable output power, output frequency dividers, and separate analog, digital, charge-pump, and VCO supplies. The analog and digital rails operate from 3.15 V to 3.45 V, while the charge-pump and VCO rails operate from 4.75 V to 5.25 V.
Does the ADF4355-3BCPZ need an external crystal?
The ADF4355-3BCPZ requires an external reference frequency, but the exact reference implementation depends on the system timing architecture. A crystal oscillator can supply that reference when its frequency and drive level meet the device requirements. The Analog Devices family information specifies an external reference input and external loop filter for normal PLL operation.
Does the ADF4355-3BCPZ meet automotive AEC-Q100 requirements?
The automotive qualification status of the ADF4355-3BCPZ should be confirmed against the ordering information in the manufacturer documentation. The verified product information identifies the part as a 6.6 GHz PLL with integrated VCO and states its -40°C to +105°C temperature range, but it does not explicitly state AEC-Q100 qualification. Do not treat industrial temperature capability as a substitute for automotive qualification.

داتای سەرچاوەی ئەندازیاری بۆ ADF4355-3BCPZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADF4355-3BCPZ when the design requires a fractional-N or integer-N synthesizer with an integrated VCO and RF operation extending to 6.6 GHz. Its programmable output power and output dividers suit receivers, transmitters, test equipment, and communication modules that need adjustable RF drive. The ADF4355BCPZ is a practical lower-frequency alternative because it uses the same 32-lead package and pinout, but its 3.3 GHz maximum output makes it unsuitable where the required channel exceeds that limit. For either device, verify the reference frequency, loop-filter component values, VCO band settings, register configuration, supply sequencing, and exposed-pad grounding in the manufacturer datasheet. Treat commercial availability, price, and lead time as separate sourcing considerations and request a current quotation for the required quantity.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADF4355BCPZ ADF4355-3BCPZ-RL7
Package 32-lead WFQFN with exposed pad 32-lead LFCSP with exposed pad 32-lead WFQFN with exposed pad
Brand Analog Devices Analog Devices Analog Devices
Maximum RF Output Frequency 6.6 GHz 3.3 GHz 6.6 GHz
Synthesis Mode Fractional-N and integer-N Fractional-N and integer-N Fractional-N and integer-N

جیاکەرەوە سەرەکییەکان

  • Higher maximum RF output than the lower-range family member (بەراورد بەADF4355BCPZ)
  • Separate digital and high-voltage RF supply domains (بەراورد بەADF4355BCPZ)
  • Programmable RF drive and flexible output division (بەراورد بەADF4355BCPZ)

تێبینییەکانی دیزاین

Treat the exposed pad as the primary thermal and electrical-ground path. Tie it to the same solid ground plane used by the pins, place it directly beneath the device, and use a regular via array to spread heat into the board. Avoid placing a thermal relief beneath the pad unless the manufacturer land pattern explicitly requires it, since that can raise junction temperature and reduce RF performance.

Route the external loop-filter components and the reference clock close to their associated device pins, and keep the RF output path physically separate from the reference, serial-interface, and supply feedback routing. The exposed-pad ground connection should be continuous rather than split. Follow the pin-description and land-pattern diagrams in the manufacturer datasheet when assigning tracks and via locations.

Provide regulated, decoupled analog, digital, charge-pump, and VCO supply rails. The analog and digital sections operate from 3.15 V to 3.45 V, while the charge-pump and VCO sections require 4.75 V to 5.25 V. Place the recommended high-frequency bypass capacitors next to their supply pins and verify startup sequencing against the manufacturer guidance before enabling the RF output.

Do not substitute a pin-compatible lower-frequency part without checking the highest required channel and all related register settings. The ADF4355BCPZ shares the package arrangement but has a 3.3 GHz maximum RF output compared with 6.6 GHz for the ADF4355-3BCPZ. Also verify loop bandwidth, reference frequency, and VCO band settings rather than assuming that identical pin assignments guarantee identical RF behavior.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The verified product information identifies the ADF4355-3BCPZ as a 6.6 GHz PLL with integrated VCO and a -40°C to +105°C operating range. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not explicitly available and are therefore recorded as unknown.

داتا پشتڕاستکراوەتەوە لە: 2026-11-10 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

adf4355 3bcpz adf4355 datasheet adf4355 evaluation board adf4355 2bcpz adf4355 software adf4355 module adf4355 eval adf4355 price ADF4355-3BCPZ datasheet pdf ADF4355-3BCPZ pinout ADF4355-3BCPZ equivalent ADF4355-3BCPZ replacement ADF4355-3BCPZ vs ADF4355BCPZ ADF4355-3BCPZ 6.6 GHz PLL Analog Devices ADF4355-3BCPZ

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADF4355-3BCPZ ADF4355BCPZ ADF4355-3BCPZ-RL7 phase-locked loop PLL fractional-N synthesizer integer-N synthesizer integrated voltage-controlled oscillator VCO clock and frequency synthesizer RF integrated circuit semiconductor 32-lead WFQFN LFCSP package family surface-mount package exposed thermal pad programmable output power output frequency divider external loop filter external reference clock charge-pump supply VCO supply hardware power-down software power-down
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ