Analog Devices

ADM231LJR - 5V 120kbps RS-232 Transceiver | Analog Devices

MPN: ADM231LJR ✓ چالاک
5 V Vdss 16-lead SOP gull-wing package Package
MOQ: 1 |

ADM231LJR گشتی

The Analog Devices ADM231LJR is a 5 V powered CMOS RS-232 driver and receiver capable of 120 kB/s data transmission. The 16-lead gull-wing SOP package combines one supply rail, on-board DC-DC converters, low-power shutdown, and receiver operation during shutdown in a compact industrial interface circuit.

An RS-232 transceiver is an interface IC that converts logic-level transmit and receive signals into differential-voltage, bipolar serial-line signals. Its functional hierarchy is RS-232 transceiver, line driver and receiver, communications interface IC, and broader semiconductor category. The ADM231LJR belongs to the ADM23xL family of single-supply RS-232 devices designed for industrial, instrumentation, and data-communication equipment.

The ADM231LJR operates from a single 5 V supply and supports data rates up to 120 kB/s. Its on-board DC-DC converters produce the bipolar signal voltages required by RS-232 without a separate external charge-pump supply. The device provides 9 V output swing from a 5 V supply and uses only 1 F charge-pump capacitors, reducing board area compared with implementations requiring larger external capacitors.

Power management features include low-power shutdown and receivers that remain active while the transmitter is shut down. This arrangement allows a system to monitor an RS-232 connection, detect activity, or wake a host without powering the full driver. The receiver input withstands voltages up to 30 V, improving tolerance to exposed industrial cabling and off-state bus conditions.

Typical uses include industrial serial consoles, test and measurement equipment, point-of-sale terminals, programmable logic controllers, and embedded instruments that exchange serial data over longer cable runs than a logic-level UART. The 120 kB/s rate is suitable for configuration links, diagnostics, firmware update paths, and moderate-rate control data rather than continuous high-bandwidth streaming.

The main design trade-off is power dissipation. A 5 V-only supply rail simplifies system power, but the DC-DC converters add internal switching activity compared with a dual-polarity implementation. Follow the recommended capacitor and charge-pump layout in the manufacturer datasheet, keep the RS-232 connector side of the circuit physically separated from sensitive analog and digital nodes, and provide a controlled signal ground reference.

جێگرەوەکانی جێگۆڕکێ بۆ ADM231LJR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM231LJR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Charge-Pump Capacitor Value, DC-DC Converter, Maximum Data Rate, Number of Drivers.

Analog Devices
Product Type: RS-232 line-driver and receiver transceiver
Charge-Pump Capacitor Value: 1 µF
DC-DC Converter: Onboard
بەراوردکردن لەگەڵ ADM231LJR →
Analog Devices
Product Type: RS-232 line driver and receiver IC
Number of Drivers: 4
بەراوردکردن لەگەڵ ADM231LJR →

ADM232LJR

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 16-lead SOIC
RS-232 line-driver and receiver transceiver · 5 V · 2 · 2 · 120 kbps · ±9 V · 1 µF · 30 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADM231LJR تایبەتمەندییەکان

Product Type CMOS RS-232 driver/receiver transceiver
ڤۆڵتیەی دابینکردن 5 V
Power Supply Configuration Single supply
Maximum Data Rate 120 kB/s
Output Swing 9 V with a 5 V supply
Charge-Pump Capacitor Value 1 F
DC-DC Converter On-board
Shutdown Low-power shutdown supported
Receiver Operation During Shutdown Receivers active in shutdown
Maximum Receiver Input Voltage 30 V
Number of Terminals 16
Package Type 16-lead SOP gull-wing package
جۆری دامەزراندن Surface mount
Temperature Grade Commercial
Interface Standard EIA-232-E and V.28
Supply Configuration Single 5 V power supply

ڕێنمایی ڕێکخستنی پینی ADM231LJR 16-lead sop gull-wing package

ڕێکخستنی پین بۆ ADM231LJR (پاکێجی 16-lead sop gull-wing package). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 16-lead sop gull-wing package بۆ ADM231LJR

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM231LJR.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADM231LJR گونجاوە بۆ 6 بەکارھێنانs: Industrial Serial Console Interface, Test and Measurement Equipment Port, Programmable Logic Controller Service Port, Point-of-Sale Terminal Peripherals, Embedded Instrumentation Data Link, Portable and Service Communications.

🏭

Industrial Serial Console Interface

The ADM231LJR fits an industrial console port that must generate RS-232 levels from a single 5 V logic rail. Its 120 kB/s maximum data rate supports terminal sessions, configuration menus, and diagnostic traffic, while the on-board DC-DC converters eliminate a separate negative voltage source. The receiver can remain active during shutdown, allowing a controller to detect a remote connection request before restarting the transmitter. Place the device near the connector, route each differential line as a short pair, and connect the interface ground to chassis or circuit ground according to the equipment's grounding strategy.

📟

Test and Measurement Equipment Port

The ADM231LJR is appropriate for instrument control ports that transfer commands, measurements, and calibration data over RS-232. A 120 kB/s rate is more than sufficient for many legacy instrument protocols, while the single 5 V supply simplifies front-panel board design. The 1 F charge-pump capacitors help limit the footprint needed around the transceiver, and the 30 V receiver-input tolerance provides additional margin on externally exposed cabling. Maintain separation between the connector-side circuit and sensitive analog measurement nodes to reduce converter noise coupling into high-impedance front ends.

🖥️

Programmable Logic Controller Service Port

The ADM231LJR can serve as the service and programming port of a programmable logic controller that already operates from 5 V logic. It supports firmware download, register diagnostics, and maintenance traffic at rates within the 120 kB/s limit. Receiver operation during shutdown is useful for detecting that a maintenance laptop has connected to an inactive controller. For cabinet-mounted equipment, add connector-level surge protection and use a chassis-ground reference appropriate for the installation. Verify the protocol's timing and line-driver requirements before selecting the baud rate and cable length.

🖨️

Point-of-Sale Terminal Peripherals

The ADM231LJR is well suited to legacy point-of-sale peripherals that use a 5 V controller and an RS-232 connector for receipt printers, scanners, or customer displays. Its 120 kB/s capability covers short control commands and compact transaction records without requiring a high-speed serial interface. The on-board DC-DC converters remove the need for a negative supply rail, while the small 1 F charge-pump capacitors assist with compact board layouts. Keep the interface cable away from display and switching-supply traces, and terminate the logic-side receive path according to the host UART configuration.

🧩

Embedded Instrumentation Data Link

The ADM231LJR provides a practical single-rail interface for embedded instruments that must send sensor records or status data to a host computer. The 120 kB/s limit suits periodic telemetry and command traffic rather than sustained bulk streaming, and the commercial temperature grade is appropriate for standard indoor equipment. The active-in-shutdown receiver allows a low-power embedded instrument to detect a connection request and resume full operation. Use the device's recommended charge-pump capacitor layout and keep the RS-232 traces away from ADC reference and precision analog inputs to minimize switching-converter interference.

📱

Portable and Service Communications

The ADM231LJR is useful in service and communications equipment where a 5 V-powered controller must connect to an older RS-232 port. Its single-supply operation reduces connector-board complexity, while the receiver's 30 V input rating offers useful robustness against idle or transient cable conditions. The 120 kB/s data rate supports maintenance commands, status dumps, and firmware transfer procedures. In battery-powered equipment, take advantage of shutdown control and the active receiver to avoid keeping the complete driver section energized. Validate sleep current and wake-up timing against the system power budget.

What is the ADM231LJR?
The ADM231LJR is a single-supply, 5 V CMOS RS-232 driver and receiver rated for data rates up to 120 kB/s. According to the Analog Devices ADM231L/232L/233L/234L family datasheet, the device includes on-board DC-DC converters, 1 F charge-pump capacitors, low-power shutdown, and receivers that stay active during shutdown. It is intended for equipment that requires RS-232 bipolar signaling from a single 5 V rail.
Does the ADM231LJR need a negative voltage supply?
The ADM231LJR requires only a single 5 V supply because its on-board DC-DC converters generate the bipolar voltages needed for RS-232 transmission. The manufacturer datasheet lists a 9 V output swing from the 5 V supply. This simplifies power-system design compared with transceivers that require a positive and a negative supply, although the internal conversion circuitry still creates switching activity that must be considered during layout.
What is the maximum data rate of the ADM231LJR?
The ADM231LJR supports a maximum data rate of 120 kB/s. The Analog Devices family datasheet identifies this capability alongside compliance with the EIA-232-E and V.28 interface specifications. It is appropriate for configuration links, firmware transfers, diagnostics, and industrial control traffic, while higher-throughput streaming applications should use a transceiver explicitly rated for the required baud rate and cable loading.
Can the ADM231LJR receivers operate while the transmitter is shut down?
Yes, the ADM231LJR receivers remain active during low-power shutdown. This feature lets a powered-down interface still detect a remote signal, which is useful for activity monitoring, wake-up detection, and systems that must observe the link without keeping the driver section fully operational. The Analog Devices family datasheet lists both low-power shutdown and active receivers in shutdown as defining device features.
What is the maximum receiver input voltage of the ADM231LJR?
The ADM231LJR receiver input is rated to 30 V. The Analog Devices family datasheet lists 30 V receiver input as a feature of the device. This higher-voltage tolerance is valuable on industrial RS-232 cables where an unpowered or idle receiver may be exposed to voltage transients. Protection and signal-conditioning components should still be added when the connected port faces severe surge conditions.
Where can I download the ADM231LJR datasheet PDF?
The official ADM231LJR datasheet is available from Analog Devices through the ADM231L_232L_233L_234L_236L_237L_238L_239L_241L family data sheet. It contains the electrical characteristics, pin descriptions, interface specifications, and recommended application circuits. Use the pin-description table and typical application diagrams in that document when assigning PCB nets and laying out the charge-pump capacitors.
Where can I find the ADM231LJR pinout?
The ADM231LJR uses a 16-lead gull-wing SOP package, and its complete pin assignments are shown in the pin-description table of the Analog Devices family datasheet. The package contains the logic-side transmit and receive pins alongside the RS-232 line-side driver and receiver connections. Because the package drawings and pin tables establish the physical numbering, use those tables directly when assigning PCB tracks.
What is the difference between the ADM231LJR and the ADM232LJR?
The ADM232LJR is the closest same-family, same-package alternative identified for the ADM231LJR. Both are listed as 2/2 full RS-232 transceivers in 16-lead SOIC packages, but their shutdown and internal feature details must be checked against the family datasheet before treating one as an exact substitute. The ADM231LJR specifically provides low-power shutdown with receivers active during shutdown, which is the principal selection criterion.
Is the ADM232LJR a drop-in replacement for the ADM231LJR?
The ADM232LJR is the closest verified drop-in candidate for the ADM231LJR because it uses the same 16-lead SOIC package and is listed as a 2/2 full RS-232 transceiver. Confirm the power-down behavior, receiver enable or shutdown logic, and charge-pump pin assignments in the Analog Devices family datasheet before production use. A schematic review is required because shutdown functionality can differ between closely related family members.
What can replace the ADM231LJR?
The ADM232LJR is the best-supported replacement candidate identified for the ADM231LJR because it shares the 16-lead SOIC footprint and 2/2 RS-232 channel configuration. Cross-brand options require a separate pin-by-pin review because transceiver shutdown arrangements and charge-pump connections can differ even when the package and RS-232 channel count match. Confirm signal levels, enable polarity, and decoupling requirements before substituting any device.
What is the best Analog Devices equivalent for the ADM231LJR?
The Analog Devices ADM232LJR is the leading same-manufacturer alternative because it is listed as a 2/2 full RS-232 transceiver in a 16-lead SOIC package. The ADM231LJR combines 120 kB/s operation, low-power shutdown, and receivers that remain active during shutdown. Select the ADM232LJR only after verifying that its shutdown architecture satisfies the system requirement; otherwise, retain the ADM231LJR.
When should I choose the ADM231LJR instead of the ADM232LJR?
Choose the ADM231LJR when the design specifically needs its low-power shutdown mode with the receiver section remaining active during shutdown. The Analog Devices family datasheet identifies both behaviors as features of the ADM231LJR, making it useful for wake-up detection and link monitoring. Choose the ADM232LJR instead only after confirming that its shutdown and enable functions satisfy the same system-level requirements.
Is the ADM231LJR suitable for industrial control and instrumentation?
The ADM231LJR is suitable for many industrial control and instrumentation links because it supports the EIA-232-E and V.28 specifications, operates from one 5 V rail, and tolerates receiver inputs up to 30 V. Its 120 kB/s rate suits configuration, diagnostic, and moderate-rate control traffic. The final design still requires grounding, surge protection, and connector-level validation for the target industrial environment.
Where can I buy the ADM231LJR and what does it cost?
The current commercial terms for the ADM231LJR are handled through the Request a Quote form on this page. Submit the required quantity, packaging preference, and target delivery schedule to obtain current availability, lead time, and a formal quotation. The request also allows the sourcing team to confirm whether any lot changes or date-code requirements apply to the ordered devices.
How should the ADM231LJR charge-pump capacitors be placed?
Place the ADM231LJR charge-pump capacitors close to their associated IC pins and follow the layout shown in the typical application circuit in the Analog Devices family datasheet. The device uses 1 F capacitors, so short, direct connections help contain high-frequency charge-pump energy. Keep the switching loop compact, provide the specified bypass capacitance at the supply pins, and separate the charge-pump return path from sensitive analog signal grounds.

داتای سەرچاوەی ئەندازیاری بۆ ADM231LJR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADM231LJR when your design needs a 5 V-only RS-232 interface with data rates up to 120 kB/s, small 1 F charge-pump capacitors, and a receiver that can detect activity while the transmitter is shut down. These characteristics suit service ports, industrial diagnostics, and instrumentation with remote wake-up requirements. The ADM232LJR is the closest verified same-package alternative for a 2/2 RS-232 design, but its shutdown and enable behavior should be verified before substitution. Do not choose an alternative solely by package count; the charge-pump connections, shutdown polarity, and receiver enable logic determine true drop-in suitability. For designs requiring more than one 5 V rail, isolated data links, or channels beyond the 2/2 configuration, evaluate a different transceiver family and revise the footprint rather than forcing an unverified substitution.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADM232LJR
Package 16-lead SOP gull-wing package 16-lead SOIC
Brand Analog Devices Analog Devices
Interface RS-232 driver/receiver transceiver 2/2 full RS-232 transceiver

جیاکەرەوە سەرەکییەکان

  • Receivers remain active during shutdown (بەراورد بەADM232LJR)
  • Single 5 V rail with integrated bipolar voltage generation (بەراورد بەADM232LJR)
  • Higher receiver-input voltage tolerance (بەراورد بەADM232LJR)

تێبینییەکانی دیزاین

Place the 1 F charge-pump capacitors directly across the corresponding ADM231LJR pins, following the polarity and connection shown in the Analog Devices family datasheet. Keep these loops as short as practical because the on-board DC-DC converters produce high-frequency energy. Route the charge-pump return current away from the receiver reference node and place the supply bypass capacitor at the device's 5 V pin rather than near the connector.

Do not treat logic-level UART signals and RS-232 line signals as interchangeable. The transmit input is referenced to the device's logic ground, while the RS-232 driver outputs bipolar voltage relative to the signal ground. Connect the interface signal ground to the appropriate chassis or circuit ground at the system boundary, and avoid leaving the connector-side driver outputs floating when a cable is disconnected.

Keep the RS-232 connector-side traces away from sensitive analog inputs, crystal circuits, and precision references. The internal DC-DC conversion required by a 5 V-only implementation can couple switching energy into the board. Use a deliberate ground strategy, keep the charge-pump current path compact, and verify conducted and radiated emissions on the finished assembly rather than relying only on schematic-level spacing.

Account for the converter loss when calculating current consumption. The ADM231LJR operates from 5 V and supports shutdown with receivers remaining active, so the receiver and internal converter may continue drawing current after the transmitter section is disabled. For battery-operated equipment, measure the shutdown current at the system level and confirm that the wake-up and remote-activity detection functions meet the product's power budget.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The commercial-temperature designation is listed for the ADM231LJR. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations should be confirmed against the current manufacturer product documentation or declaration of conformance.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADM231LJR datasheet ADM231LJR datasheet pdf ADM231LJR pinout ADM231LJR 16-SOIC pinout ADM231LJR specifications ADM231LJR 120 kB/s RS-232 Analog Devices ADM231LJR ADM231LJR equivalent ADM231LJR replacement ADM231LJR vs ADM232LJR ADM231LJR drop-in replacement ADM231LJR application circuit ADM231LJR price ADM231LJR stock what is the ADM231LJR used for

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices ADM231LJR ADM232LJR ADM23xL family RS-232 RS-232 transceiver line driver line receiver CMOS transceiver interface IC communications interface EIA-232-E V.28 single 5 V supply on-board DC-DC converter charge-pump capacitor 1 F capacitor low-power shutdown 120 kB/s data rate 9 V output swing 30 V receiver input 16-lead SOIC gull-wing package surface mount
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ