ADM483JRZ - 250 kbps RS-485/RS-422 Transceiver | Analog Devices
MPN: ADM483JRZ ✓ چالاکADM483JRZ گشتی
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and receives differential signals back into logic-level outputs. The RS-485 standard supports multipoint, half-duplex buses, while RS-422 provides balanced point-to-point or multidrop signaling. These differential interface ICs belong to the broader transceiver and interface IC hierarchy used to connect controllers, sensors, meters, industrial equipment, and communications systems over cables longer than ordinary logic interconnects.
Key features include a maximum data rate of 250 kbps, low shutdown supply current of 100 nA, and low operating supply current of 120 µA. The device provides a -7 V to +12 V bus common-mode range and can support up to 32 transceivers on one bus. Driver outputs become high impedance when disabled or powered off, while thermal shutdown and short-circuit protection improve robustness in demanding wired networks.
The ADM483 is designed for balanced data transmission over multipoint bus lines and complies with EIA RS-485 and RS-422 interfaces. Its slew-rate-limited output reduces EMI by slowing edge transitions, an important consideration in industrial environments containing clocks, motors, switching supplies, and long cable runs. The receiver provides differential signaling, allowing common-mode voltage differences on the bus to be rejected rather than appearing as noise at the logic interface.
Typical applications include industrial control networks, building automation, instrumentation, security equipment, industrial modems, and low-speed data acquisition systems. The 250 kbps rate is appropriate for supervisory communications and control traffic rather than high-bandwidth Ethernet or video transport. Half-duplex operation also requires the system controller to arbitrate bus direction so that only one transmitter drives the pair at a time.
For PCB implementation, place the device near the connector and route the differential bus as a controlled-impedance pair. Keep the ground reference close to the signal path and provide low-ESR bypass capacitance at the supply pins. Confirm termination, biasing, protection, and cable-length requirements for the selected RS-485 network because the transceiver alone does not determine the completed bus topology.
This page consolidates the ADM483JRZ electrical characteristics, verified package information, drop-in cross-references, interface selection guidance, and practical PCB considerations into a procurement-oriented engineering reference.
جێگرەوەکانی جێگۆڕکێ بۆ ADM483JRZ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADM483JRZ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Maximum Data Rate, Operating Temperature Range, Supply Voltage, Supported Standards.
MAX483ESA+
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADM383
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADM4850ARZ-REEL7
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADM485JRZ
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DS75176BM
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ADM483JRZ تایبەتمەندییەکان
| Product Type | RS-485/RS-422 differential line transceiver |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| ڤۆڵتیەی دابینکردن | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 250 kbps |
| Duplex Mode | Half-duplex |
| Supported Protocols | EIA RS-485 and EIA RS-422 |
| Bus Common-Mode Range | -7 V to +12 V |
| Shutdown Supply Current | 100 nA |
| Operating Supply Current | 120 µA |
| Maximum Transceivers per Bus | 32 transceivers |
| Output Behavior When Disabled | High impedance |
| Driver Edge Control | Slew-rate limited |
| Protection Features | Thermal shutdown and short-circuit protection |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +85 °C |
| پاکێج | 8-SOIC, 0.154 in (3.90 mm) body width |
| جۆری دامەزراندن | Surface mount |
| Packaging | Tube |
ڕێنمایی ڕێکخستنی پینی ADM483JRZ 8-soic, 0.154 in (3.90 mm) body width
ڕێکخستنی پین بۆ ADM483JRZ (پاکێجی 8-soic, 0.154 in (3.90 mm) body width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADM483JRZ.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ADM483JRZ گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Networks, Building Automation, Industrial Instrumentation, Security and Access Systems, Data Acquisition Systems, Point-to-Point RS-422 Links.
Industrial Control Networks
The ADM483JRZ suits industrial control networks that carry supervisory commands, sensor status, and equipment-state information over a balanced RS-485 bus. Its 250 kbps maximum data rate is ample for slow control traffic, while slew-rate-limited edges help limit EMI from long factory cables. The one-driver/one-receiver arrangement supports half-duplex multipoint communication, provided the controller properly arbitrates transmit direction. A -7 V to +12 V bus common-mode range improves tolerance of field-side voltage variation, while short-circuit and thermal protection protect the interface during wiring faults.
پێشنیارکراو
Building Automation
The ADM483JRZ can connect building controllers, room modules, sensors, and actuators over a low-speed RS-485 communications backbone. The 250 kbps limit is appropriate for configuration commands and periodic status reporting rather than high-volume data transfer. Its 120 µA operating supply current and 100 nA shutdown current are useful for remote endpoints that spend substantial time disabled. The half-duplex topology also reduces wiring compared with separate receive and transmit paths, although the system must provide driver-enable arbitration and suitable bus termination.
پێشنیارکراو
Industrial Instrumentation
The ADM483JRZ is appropriate for connecting meters, transducers, analyzers, and laboratory equipment that communicate over RS-422 or RS-485. Balanced differential signaling rejects common-mode noise present around industrial equipment, while the receiver supports robust cable-based data acquisition. The 250 kbps rate is suitable for sampled readings, configuration commands, and diagnostic records rather than waveform streaming. Designers should use a twisted differential pair, provide a continuous ground reference, and verify the maximum cable length against the selected data rate and system noise environment.
پێشنیارکراو
Security and Access Systems
The ADM483JRZ can serve as the wired communications interface in access-control panels, intercoms, alarm concentrators, and building-security gateways. Half-duplex RS-485 supports multiple nodes on one cabling run and reduces the number of conductors required for supervisory communication. The device’s low shutdown current is valuable in systems that periodically power down peripheral nodes, while its limited 250 kbps rate comfortably accommodates commands and event notifications. Production designs should add surge protection at accessible connectors and verify termination and fail-safe biasing for each bus segment.
پێشنیارکراو
Data Acquisition Systems
The ADM483JRZ links remote sensors, counters, and data-collection modules to a central controller in a half-duplex RS-485 network. Its differential receiver and driver help maintain data integrity when sensor wiring runs near motors, relays, or switching power converters. The 250 kbps maximum rate supports frequent control and status updates without imposing a high bandwidth demand. For multi-drop installations, the network should include termination only at the physical ends, bias resistors to maintain a defined state when all drivers are disabled, and a common reference conductor where permitted by the system architecture.
پێشنیارکراو
Point-to-Point RS-422 Links
Although the ADM483JRZ is frequently used on RS-485 multipoint buses, its differential driver and receiver also support EIA RS-422 links between two systems or across a multidrop arrangement. Balanced signaling is useful when a controller must communicate reliably with a remote instrument over a longer cable than an ordinary single-ended interface would tolerate. The 250 kbps data rate remains appropriate for commands, measurements, and status information. When using RS-422, verify the exact enable configuration and termination arrangement against the manufacturer pin description and the intended network topology.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ADM483JRZ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX483ESA+ | ADM383 | ADM4850ARZ-REEL7 | ADM485JRZ | DS75176BM |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Maxim Integrated | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Product Type | RS-485/RS-422 half-duplex transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver | RS-485 transceiver |
| Number of Drivers/Receivers | 1/1 | 1/1 | 1/1 | 1/1 | 1/1 | 1/1 |
| Supply Voltage | 4.75 V to 5.25 V | 5 V | 5 V | 5 V | 5 V | 5 V |
جیاکەرەوە سەرەکییەکان
- Matches the low-speed RS-485/RS-422 class with controlled edge transitions (بەراورد بەDS75176BM)
- Provides a 100 nA shutdown supply current (بەراورد بەMAX483ESA+)
- Supports a -7 V to +12 V bus common-mode range (بەراورد بەADM4850ARZ-REEL7)
تێبینییەکانی دیزاین
Place the ADM483JRZ close to the external connector and route the RS-485 or RS-422 bus as a twisted differential pair with substantially matched lengths. Keep the pair away from switching nodes and high-current paths. Connect the supply bypass capacitor directly between the device supply and ground pins, and provide a low-impedance ground path that follows the cable reference conductor. The exact pin names and enable functions must be assigned from the manufacturer pin-description table.
Do not enable more than one driver on the same RS-485 segment at a time. Half-duplex operation requires the controller to assert driver enable only while transmitting and to release it before receiving. Configure fail-safe biasing so the bus has a valid state when every driver is high impedance, and place termination resistors only at the physical ends of the bus. Incorrect termination or multiple active drivers can prevent reliable reception even when the ADM483JRZ operates within all electrical ratings.
The ADM483JRZ uses slew-rate-limited edges to reduce EMI, but cable and board layout still determine radiated and conducted noise. Keep transceiver supply decoupling compact, avoid long parallel stubs, and maintain a continuous reference conductor along the bus. For connectors exposed to industrial transients, add appropriately rated surge and ESD protection with the required external protection network. Verify the assembled design for both emissions and immunity in the target equipment class.
زانیاری پابەندبوون
The available product information identifies an industrial-temperature ADM483 transceiver but does not provide extractable RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 qualification is not indicated for this part.