Texas Instruments

ADS7805P - 16-Bit 100 kSPS SAR ADC, +/-10 V Input | Texas Instruments

MPN: ADS7805P ✓ چالاک
+5 V single supply operation Vdss 28-pin PDIP, through-hole Package
MOQ: 1 |

ADS7805P گشتی

The Texas Instruments ADS7805P is a 16-bit, 100 kSPS sampling CMOS successive-approximation (SAR) analog-to-digital converter with a +/-10 V analog input range, a full 16-bit parallel data output, and operation from a single +5 V supply, packaged in a 28-pin PDIP. The converter accepts unipolar or bipolar analog signals directly without external front-end scaling, and its 86 dB minimum SINAD with a 20 kHz input supports precision instrumentation measurement.

An SAR ADC is a type of analog-to-digital converter that compares the unknown input voltage against a capacitor-based internal DAC during a series of clocked bit trials. The result is a linear regulator hierarchy sibling: ADC sits under data converter, which sits under mixed-signal and analog semiconductors, and then under integrated circuit and semiconductor. Compared with pipeline or delta-sigma converters, the SAR architecture converts one sample per conversion cycle with no pipeline latency, which makes it ideal for multiplexed data-acquisition front ends.

Key features include a 100 kHz minimum sampling rate, a 16-bit resolution with no missing codes, +/-3.0 LSB maximum integral nonlinearity, and 16-bit differential nonlinearity. The device uses either an internal reference or an external reference for ratiometric or off-set calibration, and its 16-bit parallel output bus can be read directly by a microprocessor, DSP, or FPGA with three-state drivers for shared-bus designs.

The internal architecture is a capacitor-based charge-distributing SAR core with an integrated sample-and-hold, on-chip reference, clock, and microprocessor-compatible interface. Because the sample-and-hold front end is on chip, no external acquisition multiplexer or sample-and-hold amplifier is needed for single-ended or differential measurement, and the converter operates from a single +5 V analog and digital supply, simplifying board partitioning.

Typical applications include industrial process control and data acquisition modules, instrumentation and test benches, PLC analog input cards, medical monitoring equipment, audio and speech analysis front ends, and factory automation signal conditioning. The device is pin-compatible with the 12-bit ADS7804, so an existing parallel-bus board can be upgraded to 16-bit resolution in the same footprint and with the same software timing.

When designing around the ADS7805P, remember that a single +5 V supply still requires a clean analog ground plane and decoupling close to the supply pins. Because the parallel interface toggles on every conversion, keep the data bus short, use series damping resistors on long traces, and latch or buffer the result in external logic if the bus must cross a board boundary.

This page brings together the converter's key electrical characteristics, pin-compatible drop-in alternatives, and applied design guidance that are not consolidated in a single manufacturer document, helping engineers qualify the part quickly for new analog front-end designs.

جێگرەوەکانی جێگۆڕکێ بۆ ADS7805P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADS7805P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Architecture, Input Type, Package, Reference, Mounting Type.

Texas Instruments
Package: 28-pin PDIP (N)
Reference: Internal 2.5 V with option for external reference
Mounting Type: Through-Hole
بەراوردکردن لەگەڵ ADS7805P →
Texas Instruments
Architecture: SAR (Successive Approximation)
Input Type: Single-Ended
Mounting Type: Through-Hole
بەراوردکردن لەگەڵ ADS7805P →
Texas Instruments
Architecture: CMOS sampling ADC
Input Type: Bipolar, ±10 V
Package: 28-pin SOIC (DW)
بەراوردکردن لەگەڵ ADS7805P →

ADS7805UB

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-28
Successive Approximation Register (SAR) · 16 bit · 1 channel · 100 kSPS minimum · 10 us · ±10 V · 86 dB minimum with 20 kHz input · Parallel microprocessor interface

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADS7805PG4

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-28
16 · 100 kSPS · 10 µs · 1 · Single-Ended · ±10 V (or 0-4 V, 0-5 V) · Parallel · SAR (Successive Approximation)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADS7821P

✅ جێگرەوەی ڕاستەوخۆ
📦 PDIP-28
Same 16-bit converter class in the same 28-pin PDIP footprint, but multiplexing and interface details differ; resolution matches while sampling rate differs (approx. 80% match)

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ADS7804P

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-28
12-bit successive-approximation ADC · 1 input · 12 bits · 100 kSPS · 10 us · 5 V · -40 °C to +85 °C · Industrial

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADS7805P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

وردی 16 bit
Architecture Successive Approximation Register (SAR), capacitor-based
ڕێژەی نموونەگرتن 100 kSPS minimum
Conversion Time 10 us
Analog Input Range +/-10 V
Input Channels 1 (single input)
SINAD 86 dB minimum with 20 kHz input
Integral Nonlinearity (INL) +/-3.0 LSB maximum
Differential Nonlinearity (DNL) 16 bit, no missing codes
ڤۆڵتیەی دابینکردن +5 V single supply operation
Reference Internal or external reference
Output Interface Full parallel data output with 3-state drivers
Input Type Single-ended and differential capable
پاکێج 28-pin PDIP, through-hole
ژمارەی پینەکان 28
جۆری دامەزراندن Through-hole (THT)

ڕێنمایی ڕێکخستنی پینی ADS7805P 28-pin pdip, through-hole

ڕێکخستنی پین بۆ ADS7805P (پاکێجی 28-pin pdip, through-hole). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 28-pin pdip, through-hole بۆ ADS7805P

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADS7805P.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADS7805P گونجاوە بۆ 6 بەکارھێنانs: Industrial Process Control and Data Acquisition, Instrumentation and Test Bench Measurement, Medical Monitoring Equipment, Audio and Speech Analysis Front Ends, Factory Automation Signal Conditioning, Precision Sensor Acquisition Modules.

🏭

Industrial Process Control and Data Acquisition

The ADS7805P suits process measurement cards that read standard +/-10 V plant signals directly, removing the need for input attenuation and gaining 16-bit resolution instead of 12 bit. At 100 kSPS, one converter can service several multiplexed channels inside a fast acquisition window, while the 16-bit parallel bus feeds a microprocessor or DSP with one word per conversion. The single +5 V supply simplifies back-panel power distribution in control cabinets, and the 86 dB minimum SINAD supports tight loop control on slow-changing pressure, flow, and temperature signals. Use the pin description table in the manufacturer datasheet to route the parallel bus away from analog inputs.

🔧

Instrumentation and Test Bench Measurement

In laboratory and production test equipment, the ADS7805P provides the combination of 16-bit resolution, 100 kSPS throughput, and a +/-10 V input range that makes it a practical front end for reading arbitrary-range test voltages. Because the converter is pin-compatible with the 12-bit ADS7804, an existing instrument platform can gain about 16 times the code count simply by changing the device, without a board respin or firmware rework of the bus timing. The three-state output drivers also allow a single bus to be shared between multiple converter channels, which simplifies backplane routing in multi-channel test fixtures.

💊

Medical Monitoring Equipment

Medical monitoring instruments benefit from the ADS7805P when wide dynamic range must be captured in a compact, low-power parallel-bus design. The 16-bit resolution preserves small signal detail in bipolar transducer outputs, and the single +5 V supply matches the constrained rails found in portable and cart-based equipment. The device's single-conversion latency is valuable in patient monitoring, where successive samples must correspond to a specific point in time rather than a pipelined sample set. Designers should keep the analog input traces short, use a dedicated analog ground plane, and decouple close to the supply pins to limit coupled noise in low-level bio-signal channels.

🎧

Audio and Speech Analysis Front Ends

The ADS7805P is well suited to audio and speech analysis hardware that must capture bipolar waveform data for offline analysis, loudspeaker testing, or sound-level instrumentation. The +/-10 V input range accommodates microphone preamplifier and line-level outputs directly, and 100 kSPS sampling comfortably covers baseband audio bandwidth with margin. The 16-bit parallel output avoids serial-clock jitter concerns and feeds an FPGA or DSP directly. Because it is a single-shot SAR device rather than a filter-based converter, the raw samples are unfiltered, so designers should account for aliasing in system signal-path planning.

🏭

Factory Automation Signal Conditioning

Factory automation controllers that monitor analog machine signals can use the ADS7805P to replace 12-bit inputs with 16-bit accuracy while keeping the existing 28-pin board footprint. This matters for slow-varying but high-precision quantities such as pressure, tension, and position feedback, where quantization error can dominate the measurement budget. The parallel output can be driven directly into a PLC-oriented microprocessor interface, and the 100 kSPS rate allows a multiplexed front end to scan many sensors per control cycle. Three-state output drivers let several converters share one bus, reducing board area in dense multi-axis machine control cards.

🧩

Precision Sensor Acquisition Modules

Compact sensor acquisition modules built around ratiometric bridges and strain gauges benefit from the ADS7805P because it accepts either its internal reference or an external reference, letting the converter track sensor excitation drift for higher absolute accuracy. The 100 kSPS throughput supports sampling rate in portable vibration and condition-monitoring devices, and the single +5 V supply fits battery-derived rails after regulation. The 16-bit parallel bus can be routed into a small microcontroller with a dedicated peripheral or into a small FPGA for filtering. Care should be taken to isolate the reference and analog ground planes from the digital bus to preserve the 86 dB SINAD figure.

کورتەی بەرهەمە پێشنیارکراوەکان

ADS1254U High-resolution companion ADC for precision analog front ends بەکارهێنراوە لە: Industrial Process Control and Data Acquisition ADS1252U Texas Instruments بەکارهێنراوە لە: Industrial Process Control and Data Acquisition MCP3424-E/SL Microchip Technology بەکارهێنراوە لە: Industrial Process Control and Data Acquisition, Medical Monitoring Equipment PCM1725U Texas Instruments بەکارهێنراوە لە: Instrumentation and Test Bench Measurement, Audio and Speech Analysis Front Ends AD679KD Analog Devices بەکارهێنراوە لە: Instrumentation and Test Bench Measurement, Medical Monitoring Equipment MCP608-I/SN Microchip Technology بەکارهێنراوە لە: Instrumentation and Test Bench Measurement MCP6043-E/P Microchip Technology بەکارهێنراوە لە: Medical Monitoring Equipment PCM1748E Texas Instruments بەکارهێنراوە لە: Audio and Speech Analysis Front Ends AD9023AZ Analog Devices بەکارهێنراوە لە: Audio and Speech Analysis Front Ends AD779JN Analog Devices بەکارهێنراوە لە: Factory Automation Signal Conditioning PCA9554DWR Texas Instruments بەکارهێنراوە لە: Factory Automation Signal Conditioning TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Factory Automation Signal Conditioning MCP3424-E/ST Microchip Technology بەکارهێنراوە لە: Precision Sensor Acquisition Modules MSP430F135IPM Texas Instruments بەکارهێنراوە لە: Precision Sensor Acquisition Modules INA155UA Texas Instruments بەکارهێنراوە لە: Precision Sensor Acquisition Modules
What is the ADS7805P?
The ADS7805P is a 16-bit, 100 kSPS sampling CMOS successive-approximation (SAR) analog-to-digital converter from Texas Instruments. It accepts a +/-10 V analog input range, runs from a single +5 V supply, and drives a full 16-bit parallel data bus from a 28-pin PDIP package. According to the manufacturer datasheet, the device contains a complete 16-bit capacitor-based SAR core with an integrated sample-and-hold, reference, clock, microprocessor interface, and 3-state output drivers, so no external acquisition amplifier or sample-and-hold stage is required.
What is the sampling rate of the ADS7805P?
The ADS7805P converts at 100 kSPS minimum with a 10 us conversion time. Because the SAR architecture completes one conversion per clock cycle, throughput matches conversion time directly rather than adding a pipeline delay. The 100 kSPS rate lets the part track fast-changing analog signals while still delivering 16-bit resolution, and it lets a multiplexed front end scan several inputs sequentially within a fixed acquisition window. The device can also be driven by an external clock for deterministic sampling in synchronized multi-channel systems.
What analog input voltage range does the ADS7805P support?
The ADS7805P accepts a standard +/-10 V analog input range, which lets it measure industry-standard process signals directly without external attenuators. The input stage can also be configured for unipolar operation by tying the negative input to analog ground. Because the range is defined in volts rather than millivolts, the converter is suited to transducer and sensor conditioning in industrial equipment. The manufacturer datasheet identifies the device as a 16-bit, 10 us sampling CMOS analog-to-digital converter with a +/-10 V input range.
Does the ADS7805P operate from a single +5 V supply?
Yes, the ADS7805P operates from a single +5 V supply for both the analog and digital sections. This simplifies board partitioning because no separate negative analog supply rail is needed to handle bipolar inputs. A single-supply arrangement also reduces the number of decoupling networks and shrinks the power tree in multi-channel data-acquisition cards. The manufacturer datasheet lists single +5 V supply operation as a headline feature of the device.
What is the SINAD of the ADS7805P?
The ADS7805P delivers 86 dB minimum SINAD with a 20 kHz input signal, as stated in the manufacturer datasheet. SINAD combines signal-to-noise ratio and distortion into a single figure of merit, so it captures total conversion error rather than noise alone. An 86 dB figure corresponds to roughly 13.5 effective bits, which is typical for a well-designed 16-bit SAR converter at mid-band input frequencies. For instrumentation designs, this performance supports traceable measurement without an averaging-heavy firmware pipeline.
What interface does the ADS7805P use for data output?
The ADS7805P uses a full 16-bit parallel data output with three-state drivers. Data is presented on DB0 through DB15 and can be latched by a microprocessor, DSP, or FPGA using chip select, read, and write control signals. The three-state drivers allow several converters to share a common parallel bus, which is a common arrangement in multi-channel data-acquisition cards. Unlike serial SPI ADCs, the parallel interface reaches full 16-bit word throughput in one bus cycle with no serial clocking overhead.
Is the ADS7805P pin-compatible with the ADS7804?
Yes. The manufacturer datasheet explicitly lists the ADS7805 as pin-compatible with the 12-bit ADS7804, which means an existing 28-pin board can be upgraded from 12-bit to 16-bit resolution without changing the footprint or the parallel-bus software timing. The upgrade gives roughly 16 times the code count and about 24 dB of additional ideal resolution, which can remove the need for input amplification. The ADS7804P is therefore a common drop-in path for designs that outgrow their original converter resolution.
Where can I download the ADS7805P datasheet PDF?
The official manufacturer datasheet for the ADS7805 family is published by Texas Instruments at https://www.ti.com/lit/gpn/ads7805, and it is titled "16-Bit, 10 us Sampling, CMOS Analog-to-Digital Converter." That document contains the pin configuration, the absolute maximum ratings, the typical performance curves, and the timing diagrams needed for parallel-bus interfacing. Use the pin description table in that datasheet when assigning PCB tracks and when confirming which parallel data bits are valid in each conversion cycle.
Where can I find the ADS7805P pinout?
The 28-pin PDIP pin configuration and pin function names are listed in the pin configuration section of the Texas Instruments ADS7805 family datasheet, which is linked on this page. The device exposes the parallel data bus DB0 to DB15 along with control, clock, reference, and supply pins. Because the parallel bus drives all 16 lines on every conversion, keep the data tracks short and route them away from the analog input and reference nets. Confirm the exact pin numbering against the current datasheet revision before committing a new layout.
Where can I buy the ADS7805P online?
The ADS7805P is available from Texas Instruments through authorized distribution worldwide, and XAIPART stocks and sources this 28-pin PDIP converter on request. Use the Request a Quote form on this page to request current unit pricing, volume breaks, stock position, and delivery scheduling for your specific order quantity and target date. Supplying the required quantity and shipment destination with the request allows the quote to be returned quickly with confirmed lead time.
What is the lead time for the ADS7805P?
Lead time for the ADS7805P varies with order quantity, scheduled allocation, and current factory loading, so it is best confirmed per order rather than quoted generically. Submit a Request a Quote through the form on this page with your required quantity, package preference, and delivery date, and the current lead time and available allocation will be returned with the quotation. For prototype and evaluation builds, small quantities are typically faster to schedule than multi-thousand-piece production releases.
Is the ADS7805P in stock right now?
Current availability for the ADS7805P is confirmed through the Request a Quote form on this page, which returns live stock position along with pricing and lead time for the requested quantity. Because inventory for this converter moves with production and distribution cycles, a direct stock check at the moment of quotation is more accurate than any cached listing. Provide the target quantity and date so the response reflects the allocation that can actually be committed to your build schedule.
ADS7805P versus ADS7804P - which should I choose?
Choose the ADS7805P when your measurement resolution matters, because it delivers 16 bits at 100 kSPS with 86 dB minimum SINAD, while the ADS7804P is a 12-bit converter that is only pin-compatible, not equal in performance. Choose the ADS7804P only when a legacy 12-bit design already meets its accuracy requirement and you prefer to avoid requalifying the data path. Because both fit the same 28-pin PDIP footprint, the decision is a drop-in firmware and hardware swap once the board revision allows it.
What can replace the ADS7805P?
The closest drop-in replacements are the Texas Instruments ADS7805UB and ADS7805PG4, which share the same 28-pin PDIP footprint, 16-bit resolution, 100 kSPS rate, and +/-10 V input range of the ADS7805P. The ADS7804P is also pin-compatible at the same footprint but drops to 12-bit resolution, and the ADS7821P offers a different multiplexing arrangement in the same 28-pin package. Confirm the reference configuration, clocking scheme, and control-signal polarity in the datasheet before treating any of these as a substitute.
When should I choose the ADS7805P over the ADS7805UB?
Choose the ADS7805P when your design requires the standard Texas Instruments commercial-grade ordering option for the 28-pin PDIP converter with a 16-bit parallel bus, a 100 kSPS sampling rate, and a +/-10 V input range. The ADS7805UB carries the same core converter in the same package, so the selection normally comes down to ordering code, availability, and the grade your quality system requires for the target equipment. Both share the same pinout, so no layout change is needed between them.
Is the ADS7805P suitable for industrial instrumentation and process control?
Yes, the ADS7805P fits industrial instrumentation and process control front ends well because it accepts the standard +/-10 V process signal range directly, resolves 16 bits, and converts at 100 kSPS. The 100 kSPS rate supports multiplexing several channels through one converter, while the single +5 V supply simplifies back-panel wiring in control cabinets. For field-deployed equipment, verify the operating temperature range and environmental qualification levels for your installation before releasing the design for production.
What are the key specifications of the ADS7805P that engineers should know?
The ADS7805P is a 16-bit, 100 kSPS (10 us conversion time) SAR analog-to-digital converter with a +/-10 V input range, single +5 V operation, 86 dB minimum SINAD with a 20 kHz input, +/-3.0 LSB maximum INL, and 16-bit DNL with no missing codes. It offers internal or external reference selection, full parallel data output with three-state drivers, and a 28-pin PDIP package. It is also pin-compatible with the 12-bit ADS7804, easing resolution upgrades.
What is the best Analog Devices equivalent for the ADS7805P?
Analog Devices does not publish a direct, pin-for-pin 28-pin PDIP replacement for the ADS7805P in the available cross-reference listings, and most ADI alternatives for this class of converter use serial interfaces or surface-mount packages rather than the parallel-bus DIP outline. For that reason, the most reliable path is the Texas Instruments family itself: the ADS7805UB, ADS7805PG4, or the 12-bit ADS7804P in the identical 28-pin footprint. If you must use an Analog Devices part, plan for a footprint and interface redesign rather than a drop-in substitution.

داتای سەرچاوەی ئەندازیاری بۆ ADS7805P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADS7805P when your design needs a 16-bit, 100 kSPS SAR converter with a +/-10 V input range, single +5 V supply, and a full parallel data bus in a 28-pin through-hole package. It is the natural choice for industrial data-acquisition cards, instrumentation, and test equipment that already speak a parallel-bus protocol.

Choose the ADS7804P only if your legacy design is accuracy-limited by 12 bits and you prefer the lowest-cost, lowest-power option in the identical footprint; the resolution difference is the deciding factor.

Choose the ADS7805UB or ADS7805PG4 when ordering code, grade, or availability drives the decision, since the electrical ratings, pinout, and interface are the same as the ADS7805P.

Choose the ADS7821P when the system needs its multiplexing behavior in the same 28-pin outline rather than a purely single-channel SAR path.

In every case, confirm the reference configuration, control timing, and footprint against the current manufacturer datasheet before release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADS7805UB ADS7805PG4 ADS7821P ADS7804P
Package PDIP-28 (through-hole) PDIP-28 (through-hole) - same PDIP-28 (through-hole) - same PDIP-28 (through-hole) - same PDIP-28 (through-hole) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Resolution 16 bit 16 bit 16 bit 16 bit 12 bit

جیاکەرەوە سەرەکییەکان

  • 16-bit resolution in a legacy-compatible parallel-bus DIP outline (بەراورد بەADS7804P)
  • Full 16-bit parallel throughput with three-state drivers for bus sharing (بەراورد بەADS7821P)
  • Guaranteed 100 kSPS minimum sampling rate with 10 us conversion time (بەراورد بەADS7805PG4)
  • 86 dB minimum SINAD with a 20 kHz input for real instrumentation accuracy (بەراورد بەADS7804P)

تێبینییەکانی دیزاین

Keep the 16-bit parallel bus as short as possible and route it away from the analog input, reference, and clock nets. The data lines toggle on every conversion, so long parallel traces can act as an antenna and inject noise into the sampled signal. On long board runs, place a series damping resistor of roughly 22 to 33 ohms at the driver end of each data line, and latch the result in external logic if the bus must cross a board boundary.

Decouple the analog and digital supplies close to the device pins with a high-frequency ceramic capacitor plus a bulk capacitor, and join the analog and digital ground returns at a single point near the converter. Estimated: with a +5 V single supply and a 16-bit parallel bus toggling at 100 kSPS, supply-current value must be read from the datasheet supply-current table before sizing the bulk capacitor; do not size the network from an assumed figure. Keeping the return path tight prevents the parallel-bus return current from modulating the reference node.

Do not assume the ADS7805P can be replaced one-for-one with a serial-interface converter, and do not substitute a 12-bit part expecting equivalent accuracy. Verify three items before a board respin: the pin-compatibility statement in the manufacturer datasheet for the 12-bit ADS7804, the reference configuration (internal versus external) used by the firmware, and the control-signal timing of chip select, read, write, and clock. A footprint match alone does not guarantee identical control sequencing.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The device is a through-hole industrial analog IC; RoHS, REACH, lead-free and halogen-free declarations are published on the manufacturer product page and should be confirmed there for the exact ordering code used in production.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ADS7805P ADS7805P datasheet ADS7805P pinout ADS7805P datasheet pdf ADS7805P equivalent ADS7805P replacement ADS7805P vs ADS7804P ADS7805P cross reference Texas Instruments ADS7805P ADS7805P 16 bit parallel ADC ADS7805P PDIP-28 pinout ADS7805P 100 kSPS SAR converter ADS7805P industrial data acquisition ADS7805P price ADS7805P stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments ADS7805P ADS7805UB ADS7805PG4 ADS7804P ADS7821P ADC analog-to-digital converter SAR converter successive approximation register data converter mixed-signal IC semiconductor parallel data output three-state output drivers sample-and-hold internal reference external reference SINAD INL DNL no missing codes PDIP-28 through-hole package RoHS instrumentation data acquisition
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ