Texas Instruments

ADS7822P - 12-Bit 200kSPS MicroPower ADC | Texas Instruments

MPN: ADS7822P ✓ چالاک
2.7 V to 5.25 V Vdss 8-pin PDIP Package
MOQ: 1 |

ADS7822P گشتی

Texas Instruments ADS7822P is a 12-bit sampling analog-to-digital converter with a 200 kSPS maximum sampling rate, one analog input, and a 2.7 V to 5.25 V supply range. The device uses successive-approximation conversion and is offered in an 8-pin PDIP through-hole package for industrial-grade applications.

A sampling ADC is an analog-to-digital converter that captures a discrete sample of an input voltage and converts it into a digital code. ADS7822P belongs to the successive-approximation ADC, or SAR ADC, family within the broader ADC, data-converter, and semiconductor hierarchies. Its compact 8-pin package and low operating power make it useful where analog measurement must be added to a control, monitoring, or embedded system without introducing a high-speed, high-power converter.

The 12-bit resolution provides 4096 discrete code levels for the converter’s full input range. A 200 kSPS sampling capability supports fast-changing analog signals and periodic acquisition in industrial monitoring, sensor measurement, and embedded control. Operation from 2.7 V to 5.25 V permits use with both common low-voltage supply systems and 5 V analog circuits. The manufacturer describes the ADS7822 family as requiring very little power even while operating at the full 200 kHz rate.

The ADS7822P uses a sampling architecture and a serial interface for transferring converted results to a digital controller. Sampling, conversion, and serial communication can be coordinated to balance acquisition speed against system timing requirements. Because the exact conversion time, input impedance, reference arrangement, and interface timing are not stated in the available product summaries, designers should use the pin-description table, timing diagrams, and recommended operating conditions in the manufacturer datasheet when defining clocks, sampling intervals, and acquisition circuitry.

Typical applications include industrial sensor interfaces, process-control measurements, portable instrumentation, data acquisition modules, and embedded control systems. The 200 kSPS rate is suitable for continuous monitoring of slowly varying process signals as well as periodic capture of faster waveforms. The 2.7 V to 5.25 V operating range also simplifies designs that must operate across 3.3 V and 5 V system rails.

The principal design consideration is ensuring that the analog input, supply, grounding, and digital interface are connected exactly as specified. Keep the analog signal path compact, place input filtering and bypass capacitance close to the device pins, and route serial signals away from sensitive analog traces. Confirm acquisition timing and reference configuration against the manufacturer datasheet before fixing the system sampling rate.

This page combines the verified device identity, electrical limits, package information, replacement analysis, and practical integration guidance. It also identifies the important boundary between confirmed drop-in interchangeability and devices that may perform a similar function but do not establish pin-to-pin compatibility, helping engineers compare alternatives without overlooking footprint, interface, or acquisition-timing differences.

جێگرەوەکانی جێگۆڕکێ بۆ ADS7822P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADS7822P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Input Type, Package, Resolution.

Texas Instruments
Input Type: Single-ended analog with integrated sample-and-hold
Package: 8-PDIP (PB), 0.300 inch / 7.62 mm
Resolution: 12 bits
بەراوردکردن لەگەڵ ADS7822P →

ADS7822PBG4

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 PDIP-8
12 bits · SAR (Successive Approximation) · 1 input, single-ended · 200 kSPS · 2.7 V to 5.25 V · External VREF pin (ratiometric to VDD) · Serial SPI / QSPI / Microwire · Single-ended analog with integrated sample-and-hold

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADS7822P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

وردی 12 bit
ڕێژەی نموونەگرتن 200 kSPS
Analog Input Count 1 input
Conversion Architecture Successive-approximation (SAR)
Supply Voltage Range 2.7 V to 5.25 V
Power Classification MicroPower
پاکێج 8-pin PDIP
Package Type PDIP through-hole
Terminal Count 8
Temperature Grade Industrial
Input Type Single-ended analog input

ڕێنمایی ڕێکخستنی پینی ADS7822P pdip through-hole

ڕێکخستنی پین بۆ ADS7822P (پاکێجی pdip through-hole). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی pdip through-hole بۆ ADS7822P

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ADS7822P.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ADS7822P گونجاوە بۆ 6 بەکارھێنانs: Industrial Process Monitoring, Embedded Sensor Interface, Portable Data Acquisition, Battery-Powered Condition Monitoring, Laboratory Instrumentation, Motor and Equipment Control.

🏭

Industrial Process Monitoring

The ADS7822P suits single-channel process monitoring where a controller periodically measures a conditioned analog variable. Its 12-bit resolution provides 4096 digital code levels, while the 200 kSPS sampling rate can accommodate signals that change during the measurement interval. The 2.7 V to 5.25 V supply range supports both 3.3 V and 5 V industrial electronics. Place the converter near the front-end conditioning circuitry, use stable reference and supply bypassing, and verify conversion timing against the system control loop.

🧩

Embedded Sensor Interface

ADS7822P can digitize the output of a conditioned pressure, temperature, level, or position sensor when the system requires more than a simple threshold measurement. A 12-bit conversion provides useful resolution for slow-moving process variables, and the single-input SAR architecture supports straightforward command-based acquisition. The 8-pin PDIP footprint is particularly convenient for leaded prototype and industrial control assemblies. The input amplifier, filter, reference network, and ground return should be arranged to prevent sensor excitation and digital switching from degrading the 12-bit result.

📱

Portable Data Acquisition

The ADS7822P is appropriate for compact, low-power data-acquisition equipment that captures one analog channel at up to 200 kSPS. Its 2.7 V minimum supply supports battery-managed systems, while microPower operation helps limit energy use during periodic measurements. The converter can sit downstream of an instrumentation amplifier and anti-alias filter. Power-gating, sampling intervals, and serial-controller activity should be coordinated so the instrument remains responsive without unnecessarily increasing the overall energy budget.

⚡

Battery-Powered Condition Monitoring

For battery-powered condition monitoring, ADS7822P combines a 12-bit converter with a maximum sampling rate of 200 kSPS and a supply range beginning at 2.7 V. This allows a compact measurement channel to operate from a regulated 3.3 V rail while processing a conditioned sensor signal. Sample at the rate required by the mechanical condition rather than continuously converting at the maximum rate, and account for the converter’s active and standby behavior in the system power budget. Stable references and local bypass capacitance are essential for repeatable readings.

🔧

Laboratory Instrumentation

ADS7822P can serve as the acquisition element in a compact laboratory instrument that measures one analog input at moderate speed. Its 12-bit resolution is suitable for many slow or repetitive measurements, while 200 kSPS permits acquisition of faster transients when the complete signal path supports that bandwidth. The through-hole PDIP package simplifies assembly in laboratory fixtures and educational platforms. Use a low-noise reference, buffered input, defined anti-alias filtering, and a separate ground strategy to prevent instrument noise from limiting the achievable measurement accuracy.

⚙️

Motor and Equipment Control

ADS7822P can monitor a scaled analog feedback signal in a motor or equipment-control system, including current, temperature, or supply-related feedback. The 200 kSPS capability provides a practical conversion ceiling, while 12-bit resolution supports supervisory control and protection functions. Keep the feedback divider or amplifier close to the converter, maintain a quiet analog ground reference, and isolate switching-node energy from the measurement trace. The controller should pause conversion during unsuitable switching intervals if the application requires a consistently clean measurement.

What are the key specifications of ADS7822P that engineers should know?
The ADS7822P is a 12-bit, 200 kSPS, single-input successive-approximation ADC with a 2.7 V to 5.25 V supply range. According to the Texas Instruments product page, it requires very little power even at the full 200 kHz sampling rate. It is packaged as an 8-pin PDIP for through-hole PCB assembly. These specifications place it between low-resolution general-purpose converters and higher-speed, higher-channel-count data-acquisition devices.
What is the operating voltage of ADS7822P?
The ADS7822P operates from 2.7 V to 5.25 V, with specifications ensured across that range. According to the Texas Instruments ADS7822 datasheet and product page, the range supports both 3.3 V and 5 V systems. The external supply, analog input, and reference arrangement must still be designed to remain inside the limits defined by the manufacturer datasheet, particularly when operating close to either supply boundary.
What is the sampling rate of ADS7822P?
The ADS7822P supports a maximum sampling rate of 200 kSPS. According to the Texas Instruments product page, the converter continues to require very little power while operating at the full 200 kHz rate. Actual system throughput also depends on conversion timing, chip-select behavior, clocking, and the interval between commands, so use the datasheet timing diagrams when establishing the effective acquisition cadence.
What is the resolution of ADS7822P?
The ADS7822P provides 12-bit digital resolution, corresponding to 4096 possible code values across its conversion range. According to the Texas Instruments product page and distributor descriptions, it is a 12-bit sampling ADC with one analog input. Effective measurement resolution also depends on input conditioning, reference accuracy, noise, and the selected input range, so the nominal bit count alone does not determine overall system accuracy.
Where can I download the ADS7822P datasheet PDF?
The official ADS7822P datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ads7822.pdf. It is the appropriate document for checking the pin-description table, electrical characteristics, timing diagrams, typical application circuit, and recommended operating conditions. The official product page at https://www.ti.com/product/ADS7822 provides the device overview, ordering information, support resources, and links to related documentation.
Where can I find the ADS7822P pinout?
The ADS7822P pinout is shown in the pin-configuration section of the official Texas Instruments ADS7822 datasheet. The device is an 8-pin PDIP, so its pin numbering follows the standard counter-clockwise numbering of a PDIP with pin 1 at the upper-left when the notch is positioned upward. Use the manufacturer pin-description table when assigning supply, analog, reference, and serial-interface functions rather than relying on a generic package drawing.
What can replace ADS7822P as a drop-in part?
ADS7822PBG4 is the only confirmed drop-in candidate in the comparison results: it uses the same 8-pin PDIP configuration and is described as having consistent terminals, packages, and principal performance characteristics. No additional pin-compatible alternatives could be confirmed from the available cross-reference results. Before replacement, verify supply range, conversion timing, serial interface behavior, reference configuration, and the complete pin assignment against the Texas Instruments datasheet.
ADS7822P vs ADS7822PBG4 - which is better for a replacement?
ADS7822PBG4 is a direct functional and footprint match for ADS7822P because the comparison describes consistent terminals, packages, and principal performance characteristics. Both are identified as 8-pin PDIP devices. According to the ADS7822P versus ADS7822PBG4 comparison, replacing ADS7822P does not require modification of the terminal arrangement, provided the remaining acquisition and electrical requirements also match.
Is ADS7822P the same as ADS7816PC?
The available comparison material does not establish ADS7816PC as a pin-compatible replacement for ADS7822P. ADS7816PC appears in a comparison result, but that alone does not verify identical package dimensions, terminal assignments, resolution, sampling behavior, or interface timing. Choose it only after checking its manufacturer datasheet and comparing its pin configuration with ADS7822P. ADS7822PBG4 is the candidate specifically described as a complete package-and-terminal replacement.
What is the best Analog Devices equivalent for ADS7822P?
No Analog Devices equivalent can be confirmed as a drop-in replacement for ADS7822P from the available evidence. The AD7822 product result is a different 8-bit, multi-channel, 2 MSPS family, while ADS7822P is a 12-bit, single-input, 200 kSPS SAR converter in an 8-pin PDIP. Those differences prevent a pin-compatible claim. For a cross-brand redesign, evaluate resolution, throughput, reference, interface, package, and acquisition timing rather than treating the AD7822 as a direct substitute.
When should I choose ADS7822P over a higher-speed ADC?
Choose ADS7822P when the design needs 12-bit resolution, up to 200 kSPS single-channel sampling, operation from 2.7 V to 5.25 V, and an 8-pin PDIP footprint. A higher-speed or higher-resolution ADC may be preferable for waveform fidelity, multiple simultaneous inputs, wider temperature ranges, or more demanding acquisition timing. ADS7822P is most appropriate when its complete electrical and timing limits satisfy the measurement without requiring those additional capabilities.
Is ADS7822P suitable for industrial sensor measurement?
The ADS7822P is suitable for many industrial sensor-measurement applications that require a 12-bit, 200 kSPS, single-channel converter. Its industrial temperature grade, 2.7 V to 5.25 V supply range, and low-power operation align well with embedded process-control and monitoring systems. The analog signal must still be conditioned within the converter’s input range, and grounding, filtering, reference stability, and acquisition timing must follow the manufacturer guidance.
Where can I buy ADS7822P online?
Use the Request a Quote form on this page to request ADS7822P availability, current commercial terms, and an order quote. The form allows an engineer to identify the required 8-pin PDIP package and industrial-grade ordering configuration without relying on an unverified stock claim. Lead time and stock status should be confirmed for the exact MPN before committing a production schedule or releasing the component to assembly.
What is the price of ADS7822P?
The current commercial price for ADS7822P is shown through the Request a Quote form on this page. Pricing can vary with order quantity, inventory position, and purchasing conditions, so a quantity-specific quote provides the most useful result for a production BOM. The product is identified as an 8-pin PDIP, 12-bit, 200 kSPS ADC; include that package and MPN clearly in the request to avoid receiving an inquiry for a different ADS7822 package variant.
What is the lead time and stock status for ADS7822P?
Current ADS7822P lead time and stock status should be requested through the Request a Quote form on this page. The Texas Instruments product page identifies the ADS7822 family as an active product, but that status alone does not establish the quantity available for a specific purchase order. When requesting a quote, state the required quantity, 8-pin PDIP package, and intended production schedule so the response reflects the actual procurement requirement.

داتای سەرچاوەی ئەندازیاری بۆ ADS7822P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose ADS7822P for a new single-channel design that needs 12-bit resolution, up to 200 kSPS sampling, a 2.7 V to 5.25 V supply, and an 8-pin PDIP footprint. It is well matched to industrial monitoring, sensor interfaces, portable instruments, and embedded feedback measurements where the converter must remain simple and low-power. Select ADS7822PBG4 when procurement continuity or a confirmed direct replacement is needed; it matches the package, terminals, and principal performance characteristics. Do not substitute ADS7816PC or a member of the Analog Devices AD7822 family without a complete engineering review, because the available comparisons do not establish identical pin assignments or acquisition behavior. Before finalizing any device, verify input range, reference configuration, conversion time, interface timing, operating-temperature limits, and qualification status in the manufacturer datasheet.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ADS7822PBG4
Package 8-pin PDIP 8-pin PDIP - same package
Brand Texas Instruments Texas Instruments
Resolution 12 bit 12 bit
Sampling Rate 200 kSPS 200 kSPS
Analog Input Count 1 input 1 input
Supply Voltage Range 2.7 V to 5.25 V 2.7 V to 5.25 V
Conversion Architecture Successive-approximation (SAR) Successive-approximation (SAR)
Temperature Grade Industrial Industrial
Mounting Type Through-hole Through-hole

جیاکەرەوە سەرەکییەکان

  • Confirmed pin-compatible replacement path (بەراورد بەADS7822PBG4)
  • Compact single-channel conversion (بەراورد بەADS7822PBG4)
  • Low-voltage microPower operation (بەراورد بەADS7822PBG4)

تێبینییەکانی دیزاین

Route the analog input directly from its conditioning network to the ADS7822P input and keep the trace short. Place input filtering and bypass capacitance near the corresponding device pins, and connect the analog return through a quiet ground path rather than through digital return current. The 8-pin PDIP footprint is easy to assemble, but lead spacing does not excuse long analog traces; loop area and ground gradients can affect the usable noise performance of a 12-bit conversion.

Design the supply network for the full 2.7 V to 5.25 V operating range and place local bypass capacitance at the converter. Separate the analog supply path from high-current switching outputs where practical, and keep the reference network quiet and stable. Because exact supply-current and quiescent-current limits are not stated in the product summaries, use the manufacturer electrical-characteristics tables to size regulators and confirm behavior across sampling rates before calculating system power.

Treat the serial interface as a timed acquisition system rather than an asynchronous read of a continuously updated value. Coordinate chip select, clock, data input, and converted-data output according to the manufacturer timing diagrams. Account for propagation delay, conversion interval, controller software latency, and any required settling time when calculating the maximum end-to-end sampling cadence. Avoid scheduling a conversion immediately after an analog input step unless the datasheet confirms that the selected acquisition time is sufficient.

Do not assume that similar-resolution ADCs are interchangeable merely because their conversion results are both digital. ADS7822PBG4 is specifically identified as matching the ADS7822P terminals and package, while ADS7816PC and the AD7822 family were not confirmed as direct replacements. For any redesign, compare pin names, supply limits, reference behavior, conversion timing, serial protocol, and acquisition timing. Also verify the operating-temperature and qualification requirements rather than relying only on nominal resolution and throughput.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The available manufacturer and distributor summaries do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The industrial temperature grade is identified, but industrial grading alone does not establish AEC-Q100 qualification.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ads7822 datasheet ADS7822P datasheet ADS7822P datasheet pdf ADS7822P pinout ADS7822P specifications ADS7822P PDIP-8 ADS7822P replacement ADS7822P equivalent ADS7822P vs ADS7822PBG4 ADS7822P application circuit ADS7822P price Texas Instruments ADS7822P

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments ADS7822P ADS7822PBG4 12-bit ADC sampling analog-to-digital converter successive-approximation ADC SAR ADC analog-to-digital converter data converter semiconductor single analog input 200 kSPS sampling rate 2.7 V to 5.25 V supply PDIP-8 through-hole package industrial temperature grade serial interface reference voltage sensor interface industrial process monitoring data acquisition embedded control
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ