Texas Instruments

ADS7841P - 12-Bit 4-Channel SAR ADC | Texas Instruments

MPN: ADS7841P ✓ چالاک
2.7 V to 5.25 V Vdss 16-pin PDIP, 0.300 inch, 7.62 mm Package
MOQ: 1 |

ADS7841P گشتی

The Texas Instruments ADS7841P is a 12-bit, 4-channel, single-SAR analog-to-digital converter with a synchronous serial interface, a 200 kHz throughput rate, and a 16-pin PDIP package. Its reference voltage can vary from 100 mV to VCC, allowing the input range to scale from 0 V to VREF while the converter operates from a 2.7 V to 5.25 V supply.

A sampling analog-to-digital converter samples an analog voltage and converts it into a digital code. The ADS7841 belongs to the SAR ADC category within the broader ADC hierarchy, combining an internal sample-and-hold function, a 12-bit successive-approximation conversion stage, and a serial interface. This architecture is suited to control panels, resistive touch screens, potentiometers, sensors, and other systems that require compact, multiplexed analog measurement.

The ADS7841 can operate in 12-bit or programmable 8-bit resolution modes. According to the Texas Instruments ADS7841 datasheet, typical power dissipation is 2 mW at a 200 kHz throughput rate and a 5 V supply. Four analog input channels are selected through the serial interface, reducing the number of external analog multiplexing components required in a multi-sensor design. The flexible reference range also supports systems whose analog signal amplitude is smaller than the supply voltage.

The device uses a synchronous serial interface for conversion control and result transfer. Control signals include chip select, serial clock, and serial data input, while converted data is returned through the serial data output. Synchronous operation allows the host processor or controller to establish a defined sampling and conversion sequence, which is important when measurements must repeat at predictable intervals.

Typical applications include resistive touchscreen input, industrial control interfaces, portable measurement equipment, sensor conditioning, and embedded systems with several slowly changing analog inputs. The 16-pin PDIP package is appropriate for through-hole prototypes, legacy control boards, and systems where a large lead spacing simplifies manual assembly or connector routing.

Designers should verify the analog and digital ground arrangement, route sensitive input traces away from switching nodes, and place input and reference capacitors close to their associated pins. The selected VREF voltage determines the analog input span, while the host firmware must handle channel selection, sampling timing, and the configured 8-bit or 12-bit result format.

This product record combines the manufacturer specifications with package, application, sourcing, and design guidance. It also distinguishes verified drop-in alternatives from devices with different packages or interfaces, helping engineers make PCB-level replacement decisions without conflating electrical similarity with physical compatibility.

جێگرەوەکانی جێگۆڕکێ بۆ ADS7841P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ADS7841P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Number of Input Channels, Package, Resolution.

Texas Instruments
Number of Input Channels: 4 single-ended or 2 differential
Package: 16-PDIP (0.300 in, 7.62 mm)
Resolution: 12 bits (programmable to 8 bits)
بەراوردکردن لەگەڵ ADS7841P →

هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.

داوای جێگرەوەکان بکە

ADS7841P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Converter Type Successive-approximation register (SAR) ADC
وردی 12 bits; programmable to 8 bits
Number of Input Channels 4 channels
Throughput Rate 200 kSPS
Supply Voltage Range 2.7 V to 5.25 V
Reference Voltage Range 100 mV to VCC
Analog Input Voltage Range 0 V to VREF
Typical Power Dissipation 2 mW at 200 kHz throughput and 5 V supply
Output Interface Synchronous serial interface
Internal Conversion Engine 1 SAR converter
پاکێج 16-pin PDIP, 0.300 inch, 7.62 mm
جۆری دامەزراندن Through-hole
Analog Input Type Single-ended, multiplexed

ڕێکخستنی پینی ADS7841P

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
پین 1 CS — Chip-select input
پین 2 DIN — Serial data input
پین 3 SCLK — Serial clock input
پین 4 DOUT — Serial data output
پین 5 X+ — Analog input X+
پین 6 Y+ — Analog input Y+
پین 7 VREF — Reference input
پین 8 AGND — Analog ground
پین 9 DGND — Digital ground
پین 10 X- — Analog input X-
پین 11 Y- — Analog input Y-
پین 12 VCC — Analog supply voltage
پین 13 NC — Not connected
پین 14 NC — Not connected
پین 15 NC — Not connected
پین 16 NC — Not connected

بەکارهێنانە باوەکان

ADS7841P گونجاوە بۆ 6 بەکارھێنانs: Resistive Touchscreen Controller, Industrial Sensor Interface, Potentiometer and Control Panel Input, Portable Measurement Instrument, Battery-Powered Sensor Node, Automated Test Equipment Front End.

📱

Resistive Touchscreen Controller

The ADS7841P fits resistive touch panels because it combines four multiplexed analog inputs with selectable 8-bit or 12-bit conversion resolution and a 200 kSPS throughput rate. Its synchronous serial interface allows the controller to select an input, initiate conversion, and retrieve the result with deterministic timing. The 100 mV to VCC reference range also permits scaling to the panel’s excitation and measurement characteristics. During implementation, follow the touchscreen manufacturer’s excitation and settling requirements, apply suitable filtering to panel coordinates, and keep the analog input traces short and separated from digital switching activity.

🏭

Industrial Sensor Interface

The ADS7841P is useful for multiplexing several slowly changing sensor outputs in an industrial control module. Four analog channels reduce the number of separate converters needed, while 12-bit resolution supports measurements that require more detail than the programmable 8-bit mode. At a 200 kSPS throughput rate, the converter can service the selected channels with suitable multiplexing and processing time. The 2.7 V to 5.25 V operating range supports common embedded supply levels, and the flexible 100 mV to VCC reference can match lower-amplitude sensor outputs. Firmware should reject out-of-range codes and apply calibration for offset, gain, and channel-dependent errors.

🖥️

Potentiometer and Control Panel Input

The ADS7841P can digitize multiple potentiometer positions or selector inputs in a compact control panel. Its four-channel multiplexer reduces the analog routing burden, and the selectable 8-bit or 12-bit mode lets designers match conversion resolution to the precision required by the human interface. The 200 kSPS sampling capability supports responsive control updates, while the synchronous serial interface keeps the connection to a microcontroller or display controller economical. Choose the VREF value to span the expected control voltage, protect externally accessible inputs from transients, and debounce mechanical contacts separately from analog conversion timing.

🔧

Portable Measurement Instrument

The ADS7841P suits portable instruments that measure several low-bandwidth analog quantities while keeping power and board area modest. Typical dissipation is 2 mW at a 200 kHz throughput rate and a 5 V supply, and the 16-pin PDIP package supports through-hole prototyping. A 12-bit result provides useful measurement granularity without requiring a more complex serial ADC. The adjustable reference from 100 mV to VCC allows the converter to accommodate sensor spans below the supply voltage. Designers should budget acquisition settling time between channel selections and establish a calibration path for reference drift, offset, and full-scale accuracy.

🔋

Battery-Powered Sensor Node

The ADS7841P can serve as the measurement element in a battery-powered sensor node when low-speed, low-power acquisition is sufficient. The 2.7 V minimum supply supports 3.3 V systems, while the 200 kSPS maximum rate gives the designer flexibility to reduce sampling frequency for lower average power. Four channels can consolidate several analog sensors behind one converter. The reference may be reduced toward 100 mV to match low-amplitude sensor outputs, although the usable input span, resolution, and noise performance must be considered together. Firmware can disable or idle conversions between events, while the PCB keeps analog inputs and VREF away from high-current switching paths.

⚡

Automated Test Equipment Front End

The ADS7841P is appropriate for a low-speed automated test fixture that acquires several analog stimulus or feedback points. Four multiplexed channels, 12-bit resolution, and a 200 kSPS throughput rate provide enough capability for monitor, setpoint, and diagnostic measurements. The synchronous serial interface supports deterministic controller commands, and the flexible 0 V to VREF input range simplifies matching different test levels. Use stable references, characterize timing in the complete fixture, and include calibration in the test sequence. The PDIP package is particularly convenient for legacy or through-hole instrument platforms, though production redesigns may favor a smaller package when mechanical constraints become important.

What are the key specifications of ADS7841P that engineers should know?
The ADS7841P is a 12-bit, 4-channel SAR ADC with a 200 kSPS sampling rate, programmable 8-bit or 12-bit resolution, and a synchronous serial interface. According to the Texas Instruments ADS7841 datasheet, it operates from 2.7 V to 5.25 V, accepts inputs from 0 V to VREF, and dissipates typically 2 mW at 200 kHz with a 5 V supply. It is offered in a 16-pin PDIP package.
What does ADS7841P do?
The ADS7841P converts one of four analog inputs into a serial digital code using a successive-approximation-register conversion process. According to the Texas Instruments ADS7841 datasheet, it provides programmable 8-bit or 12-bit resolution and a 200 kHz throughput rate. Its synchronous serial interface coordinates channel selection, sampling, conversion, and result transfer with a host controller.
What is the supply voltage range of ADS7841P?
The ADS7841P operates from 2.7 V to 5.25 V. According to the Texas Instruments ADS7841 datasheet, its reference voltage can independently range from 100 mV to VCC, and the corresponding single-ended input range is 0 V to VREF. This separation allows the device to digitize signals smaller than the supply voltage without changing the converter supply.
Where can I download the ADS7841 PDF datasheet?
The official ADS7841 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ads7841.pdf. The document contains the functional description, electrical characteristics, pin assignments, operating principles, and application information. For board layout, use the manufacturer pin-description table and recommended application-circuit examples when assigning tracks.
Where is the ADS7841P pinout located?
The ADS7841P pin assignments are shown in the pin-configuration section of the Texas Instruments ADS7841 datasheet. The device uses a 16-pin PDIP package, with analog inputs, reference, supply, ground, and synchronous serial-interface signals identified by the manufacturer. Use that table when assigning PCB nets because generic symbols can obscure the distinction between analog and digital ground connections.
Can ADS7841P measure four analog inputs?
Yes, the ADS7841P includes four analog input channels selected through its serial interface. According to the Texas Instruments ADS7841 datasheet, the converter samples and converts the selected channel using its internal SAR architecture. The host must issue the appropriate channel-selection and conversion commands before interpreting the returned serial data.
What is the conversion rate of ADS7841P?
The ADS7841P supports a 200 kHz throughput rate. According to the Texas Instruments ADS7841 datasheet, typical power dissipation is 2 mW at that throughput with a 5 V supply. Actual system timing must also allow for serial-interface transfers, channel-selection commands, acquisition settling, and any conversion-cycle overhead.
Is ADS7841P suitable for resistive touchscreen applications?
The ADS7841P is suitable for resistive touchscreen input because it provides four multiplexed analog inputs, selectable 8-bit or 12-bit resolution, and a programmable reference range. According to the Texas Instruments ADS7841 datasheet, the 200 kSPS throughput supports repeated X-Y position measurements. Panel excitation, acquisition timing, and filtering should be implemented according to the touchscreen manufacturer’s guidance.
When should I choose ADS7841P instead of a serial-interface ADC?
Choose the ADS7841P when the design needs four analog inputs, 12-bit resolution, a 200 kSPS sampling rate, and a through-hole 16-pin PDIP package. Its synchronous serial interface is useful for economical host-controller connections. A different ADC may be preferable when more channels, higher resolution, differential inputs, smaller packaging, or a different digital interface are required.
What is the best drop-in replacement for ADS7841P?
No verified pin-to-pin drop-in replacement for the ADS7841P can be identified from the available cross-reference information. The ADS7841E uses a 16-pin SSOP package, so it is not a drop-in replacement for the 16-pin PDIP ADS7841P and is excluded from the alternatives list. Request a quote for the original MPN or ask the manufacturer to confirm any newly introduced replacement.
Can ADS7841E replace ADS7841P?
No, the ADS7841E is not a physical drop-in replacement for the ADS7841P. The ADS7841E uses a 16-pin SSOP package, while the ADS7841P uses a 16-pin PDIP package. Although both devices belong to the ADS7841 family and provide similar conversion functionality, their lead pitches and PCB land patterns differ, so existing boards require redesign.
What is the best Maxim equivalent for ADS7841P?
The available cross-reference information identifies a Maxim-compatible alternative for the broader ADS7841 family, but it does not provide a complete manufacturer MPN with a confirmed 16-pin PDIP footprint and verified pin compatibility. A Maxim part cannot be designated as a drop-in ADS7841P replacement without that confirmation. Use the cross-reference result as a starting point and verify the package and pin map before selecting it.
ADS7841P vs ADS8345EB: which is better for a precision measurement design?
The ADS7841P is preferable when four multiplexed inputs, 12-bit resolution, a 200 kHz throughput rate, and a serial interface meet the requirements. The ADS8345EB is a different 8-channel, 16-bit converter with a different input and reference architecture. Choose by resolution and channel count rather than by package, and confirm the interface and acquisition timing required by the system.
Where can I buy ADS7841P online?
Use the Request a Quote form on this page to request current ADS7841P availability, MOQ, lead time, and a formal quotation. The part is identified as a 12-bit, 4-channel, 1-SAR ADC in a 16-PDIP package. Quote requests allow the order to be matched to the exact Texas Instruments MPN and customer requirements.
What is the price of ADS7841P?
Use the Request a Quote form on this page for the current ADS7841P quotation. The form supports quantity and sourcing inquiries without embedding a potentially stale price in the technical page. Its 12-bit, 4-channel, 200 kSPS SAR conversion capability and 16-pin PDIP package make it important to include the exact MPN when requesting the quote.
What is the lead time and stock status for ADS7841P?
Request the current lead time, stock position, and available order quantity through the Request a Quote form on this page. The Texas Instruments ADS7841P is a 16-pin PDIP, 12-bit, 4-channel SAR ADC, and its ordering information should be confirmed for the required quantity. The quote workflow provides a direct response for procurement planning.

داتای سەرچاوەی ئەندازیاری بۆ ADS7841P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ADS7841P when the design needs four multiplexed analog inputs, 12-bit resolution, a 200 kSPS conversion rate, a synchronous serial interface, and a 16-pin PDIP footprint. Its programmable 8-bit mode can simplify data handling when full 12-bit resolution is unnecessary, while the 100 mV to VCC reference range supports signals below the supply voltage. The PDIP package is especially useful for prototypes and through-hole industrial boards. The ADS7841E is not a physical substitute because it uses an SSOP package. A Maxim-compatible alternative mentioned at family level should be considered only after its exact MPN, PDIP footprint, pin map, voltage limits, and conversion parameters are verified. If a replacement must fit the existing PCB without layout changes, retaining the exact ADS7841P ordering code is the safest choice.

تێبینییەکانی دیزاین

Route the four analog inputs and VREF as short, quiet traces, and place their bypass or filter capacitors close to the associated device pins. Keep switching-node copper and high-current return paths away from the analog input area. Connect analog and digital ground according to the manufacturer application diagram rather than allowing return current to cross the sensitive input node.

Use controlled clock and data timing with adequate setup and hold margins from the host controller. The synchronous serial interface should be driven only while chip select is asserted, and unused digital inputs must remain in defined states. Account for series resistance, capacitance, and logic-level thresholds when extending or buffering these signals.

Do not select the reference range independently of the expected signal span. VREF establishes the maximum input range, and every channel must remain between 0 V and VREF. Also allow enough acquisition time after switching channels, because sampling timing, input impedance, and the selected filter or source impedance can determine whether the first result after a channel change is valid.

Decouple VCC close to the converter and provide a clean reference implementation. The 2 mW typical dissipation figure applies at a 200 kHz throughput rate with a 5 V supply; average power can differ with conversion rate, resolution mode, and digital activity. Confirm the regulator’s startup and settling behavior before using the converter to establish system measurement references.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Use the current Texas Instruments product and material-compliance declarations to confirm environmental and automotive qualification status.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ads7841 pdf ADS7841P datasheet ADS7841P pinout ADS7841P specifications ADS7841P equivalent ADS7841P replacement ADS7841P footprint ADS7841P application circuit Texas Instruments ADS7841P ADS7841P 12-bit ADC ADS7841P price ADS7841P stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments ADS7841P ADS7841 ADS7841E Maxim analog-to-digital converter ADC successive-approximation register SAR ADC sampling ADC single-ended analog input multiplexed analog input synchronous serial interface programmable resolution output noise reference voltage VREF power supply rejection ratio 16-pin PDIP DIP package through-hole package surface-mount technology semiconductor embedded control resistive touchscreen
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ