AT90CAN64-15MT - 16MHz 64KB AVR CAN MCU | Microchip Technology
MPN: AT90CAN64-15MT ✓ چالاکAT90CAN64-15MT گشتی
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, I/O ports, and peripheral functions on one package. The AT90CAN64 belongs to the hierarchy of 8-bit RISC microcontroller, embedded controller, and programmable logic device. Its integrated CAN controller allows a design to communicate on an automotive or industrial CAN network without requiring a separate CAN transceiver. The controller is identified as compliant with CAN 2.0A and CAN 2.0B.
The family combines 128KB of ISP flash with read-while-write operation, 2KB of EEPROM, and 4KB of SRAM. In-system programming supports programming after the device has been mounted on a board. A 53-line general-purpose I/O interface provides connections for sensors, actuators, control signals, and communications peripherals. The target ordering code is identified as the industrial-temperature 16 MHz version in a 64-terminal no-lead package.
The device is based on Microchip's high-performance, low-power 8-bit AVR RISC architecture. Its instructions include most single-clock-cycle operations, while 32 general-purpose working registers support efficient execution of embedded control tasks. The CAN controller, parallel I/O, serial interfaces, and memory architecture make the family appropriate for controllers that must coordinate distributed equipment over a robust two-wire CAN network.
Typical uses include automotive body and gateway modules, industrial automation controllers, CAN-connected sensors, building equipment, and diagnostic interfaces. In these systems, the MCU can execute control logic locally while exchanging status, commands, and diagnostic information with other CAN nodes. The 64-pin QFN format supports dense PCB layouts but requires careful escape routing and exposed-pad thermal management.
Designers should use the manufacturer pin description when assigning PCB nets and should preserve the recommended programming, clock, reset, and CAN interface connections. Power sequencing, decoupling, clock stability, and exposed-pad soldering materially affect reliability. Because a wrong peripheral connection can disable programming or communications, validate the schematic and PCB against the manufacturer datasheet before release.
This page combines the verified device identity, architecture, memory, I/O, package, lifecycle, and selection information with practical CAN-system guidance. It also distinguishes exact drop-in candidates from same-family alternatives so engineers can assess replacement risk before committing a board revision.
جێگرەوەکانی جێگۆڕکێ بۆ AT90CAN64-15MT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AT90CAN64-15MT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, CAN Controller, Instruction Set, EEPROM, Microcontroller Type.
AT90CAN64-16MUR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →AT90CAN32-15MT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →AT90CAN32-15MU
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AT90CAN128-16MT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AT90CAN128-16MU
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →AT90CAN64-15MT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Microcontroller Type | 8-bit AVR RISC microcontroller |
| Maximum Clock Speed | 16 MHz |
| ISP Flash Memory | 128 KB |
| Flash Read-While-Write | Supported |
| EEPROM Memory | 2 KB |
| SRAM | 4 KB |
| General-Purpose I/O Lines | 53 |
| General-Purpose Working Registers | 32 |
| پانی بسێ داتا | 8 bit |
| Instruction Set | 133 instructions |
| CAN Controller | CAN 2.0A and CAN 2.0B compliant |
| Architecture | High-performance, low-power AVR 8-bit RISC |
| پاکێج | 64-QFN, 9 mm x 9 mm, exposed pad |
| Terminal Count | 64 |
| شێوازی دامەزراندن | No lead, surface mount |
| Temperature Grade | Industrial |
ڕێنمایی ڕێکخستنی پینی AT90CAN64-15MT 64-qfn, 9 mm x 9 mm, exposed pad
ڕێکخستنی پین بۆ AT90CAN64-15MT (پاکێجی 64-qfn, 9 mm x 9 mm, exposed pad). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ AT90CAN64-15MT.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
AT90CAN64-15MT گونجاوە بۆ 6 بەکارھێنانs: Automotive Body Control Module, Industrial CAN Gateway, CAN-Connected Sensor Node, Building Equipment Controller, CAN-Based Diagnostic Interface, CAN Actuator Controller.
Automotive Body Control Module
The AT90CAN64-15MT fits a CAN-connected body controller because it combines a 16 MHz AVR core, 128KB ISP flash, and an integrated CAN 2.0A/2.0B controller in a 64-QFN package. The MCU can manage switch inputs, lamps, relays, and diagnostic logic while exchanging vehicle-network messages. Its 53 I/O lines reduce the need for external digital I/O expanders. Qualification for a particular vehicle platform still requires confirmation of the applicable temperature, ESD, and reliability requirements.
پێشنیارکراو
Industrial CAN Gateway
The AT90CAN64-15MT is suitable for an industrial gateway that translates commands between CAN-connected equipment and another embedded interface. Its 128KB flash supports protocol conversion and diagnostics, while 4KB SRAM accommodates short frame buffers and state machines. The 53 general-purpose I/O lines provide status, alarm, and configuration connections without requiring a separate GPIO device. In operation, keep CAN routing and transceiver isolation away from sensitive analog paths on the PCB.
پێشنیارکراو
CAN-Connected Sensor Node
The AT90CAN64-15MT can serve as the control and communications hub in a distributed sensor node. The 16 MHz AVR architecture provides sufficient instruction throughput for local filtering and timing, while the integrated CAN controller supports shared-bus communication with neighboring nodes. Its 53 I/O lines can accept digital sensor outputs and control indicators, and the 2KB EEPROM can retain calibration or configuration parameters. Use the manufacturer's pin table to assign communication and sensing functions without accidental peripheral conflicts.
پێشنیارکراو
Building Equipment Controller
The AT90CAN64-15MT is well suited to HVAC, access-control, or lighting controllers that use a CAN backbone for monitoring and configuration. Its 128KB program flash can hold application firmware, communication tables, and diagnostic routines, while the 4KB SRAM supports message processing. The 53 I/O lines allow relay outputs, sensor inputs, and local status LEDs to share one controller. For long-distance building networks, validate termination, transceiver behavior, and environmental requirements during system qualification.
پێشنیارکراو
CAN-Based Diagnostic Interface
The AT90CAN64-15MT can implement a compact diagnostic interface that receives CAN requests, runs application checks, and reports results over the same network. The 16 MHz clock supports deterministic protocol handling, and 128KB flash leaves room for a bootloader, device profiles, and diagnostic tables. The integrated CAN controller eliminates the need for a separate CAN protocol IC, although a physical-layer transceiver is still required. Use bootloader and in-system programming paths described by Microchip during implementation.
پێشنیارکراو
CAN Actuator Controller
The AT90CAN64-15MT can control distributed actuators that accept commands over CAN and report operating status. Its 53 I/O lines support digital feedback, limit switches, and actuator drive-control signals, while 4KB SRAM handles command queues and state transitions. The integrated CAN 2.0A/2.0B controller simplifies protocol handling compared with a discrete CAN implementation. Care is needed when driving inductive loads because the MCU is a low-voltage control device and requires suitable external driver circuitry.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ AT90CAN64-15MT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | AT90CAN64-16MUR | AT90CAN32-15MT | AT90CAN32-15MU | AT90CAN128-16MT | AT90CAN128-16MU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-QFN, 9 mm x 9 mm, exposed pad | 64-QFN | 64-QFN | 64-QFN | 64-QFN | 64-QFN |
| Maximum Clock Speed | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Architecture | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC |
| CAN Controller Compliance | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B | CAN 2.0A and CAN 2.0B |
جیاکەرەوە سەرەکییەکان
- Largest directly documented AT90CAN64 configuration match (بەراورد بەAT90CAN64-16MUR)
- Four times the flash capacity of the AT90CAN32 alternatives (بەراورد بەAT90CAN32-15MT)
- Industrial-grade ordering identification (بەراورد بەAT90CAN64-16MUR)
- Integrated CAN protocol controller (بەراورد بەAT90CAN32-15MT)
تێبینییەکانی دیزاین
Route the CAN transceiver and connector away from clock, programming, and sensitive input nets. Keep the CAN TX and RX paths short and controlled, place the transceiver close to the connector, and follow the transceiver reference layout for termination and common-mode components. The AT90CAN64-15MT contains the CAN protocol controller but not the physical bus transceiver.
The 64-QFN package has an exposed thermal pad, so the PCB copper area under the device should use the manufacturer-recommended thermal-via and solder-pattern arrangement. Connect the exposed pad to the required power or ground net exactly as shown in the package documentation. Consistent reflow profile and adequate copper improve heat transfer without relying on a separate heatsink.
Place programming-test points, clock components, and decoupling capacitors close to their associated device pins. Maintain short return paths for the 16 MHz clock and isolate the clock network from CAN and switching nodes. Use the manufacturer pin-description table and land pattern when assigning functions so programming, reset, and communication interfaces are not routed to conflicting pins.
Do not treat AT90CAN64, AT90CAN64-15MT, and AT90CAN64-16MUR as interchangeable ordering codes. Confirm speed, temperature treatment, terminal count, package code, tape or reel format, and exposed-pad details in the Microchip ordering table. Also remember that an MCU CAN controller requires an external transceiver, power interface, termination strategy, and correctly implemented CAN physical layer.
زانیاری پابەندبوون
The AT90CAN64 is identified as an industrial-temperature device, but no specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement was included for this exact ordering code.