ATSAMD20E15A-MU - 48MHz Cortex-M0+ MCU | Microchip Technology
MPN: ATSAMD20E15A-MU ✓ چالاکATSAMD20E15A-MU گشتی
A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The Cortex-M0+ architecture places the ATSAMD20E15A-MU in the hierarchy of embedded microcontroller, 32-bit MCU, ARM Cortex-M0+ microcontroller, and general-purpose semiconductor. Its combination of embedded Flash, SRAM, serial interfaces, and analog conversion functions allows one device to supervise sensors, actuator controls, communications, and local data processing.
The device provides 32 KB of Flash for firmware and 4 KB of SRAM for working data. The listed feature set also includes I2C, SPI, UART, a 12-bit ADC, and a 10-bit DAC. These resources make the MCU suitable for home automation, consumer equipment, metering, industrial control, and other embedded applications. Operation at 48 MHz supports responsive control loops and interrupt-driven peripheral handling while retaining the simplicity associated with the Cortex-M0+ core.
The ATSAMD20E15A-MU belongs to Microchip's SAM D20 family and is identified as the SAM D20E device. Its 32-VQFN package reduces board area compared with larger leaded packages, while an exposed-pad package construction supports heat transfer from the device to the PCB copper. Exact pin identities and exposed-pad details should be taken from the manufacturer pin-description table before assigning tracks or connecting power and ground pins.
Typical applications include connected home devices, utility metering, compact industrial controllers, sensor nodes, and consumer products with local serial connectivity. For a design using I2C sensors, the MCU can act as the bus controller while handling data in its local processing loop. For a metering design, the ADC can acquire analog inputs and the UART can transfer results to a host. The 10-bit DAC can generate an analog output where the system requires a controlled reference or low-bandwidth analog signal.
Power-system design should include careful management of unused pins and peripheral states because unmanaged I/O can increase leakage current. Confirm the operating voltage configuration, decoupling requirements, clock strategy, and programming connections against the manufacturer datasheet. The small VQFN package also requires a land pattern that accommodates its exposed thermal pad and adequate solderable area.
This page combines the manufacturer's device overview with distributor packaging details, practical low-power and layout guidance, and a structured comparison of same-footprint family options. It is intended to help engineers evaluate memory capacity, pin compatibility, peripheral requirements, and package constraints before committing the ATSAMD20E15A-MU to a PCB design.
جێگرەوەکانی جێگۆڕکێ بۆ ATSAMD20E15A-MU — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ATSAMD20E15A-MU (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, ADC, MSL Level, SRAM, Operating Temperature.
ATSAMD20E15A-MUT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ATSAMD20E18A-MU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD20E16A-MU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATSAMD21E15A-AU
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
ATSAMD20E15A-MU زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 32-bit ARM Cortex-M0+ flash microcontroller |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB (32K x 8 bits) |
| SRAM | 4 KB |
| ADC Resolution | 12 bits |
| DAC Resolution | 10 bits |
| Number of I/O Pins | 26 pins |
| پاکێج | 32-VQFN, 5 x 5 mm |
| Total Package Pins | 32 pins |
| Operating Voltage Range | 1.8 V, 2.5 V, or 3.3 V configurations |
| Serial Interfaces | I2C, SPI, and UART |
| Low-Power Modes | Supported; detailed mode conditions not stated |
ڕێنمایی ڕێکخستنی پینی ATSAMD20E15A-MU 32 pins
ڕێکخستنی پین بۆ ATSAMD20E15A-MU (پاکێجی 32 pins). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ATSAMD20E15A-MU.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ATSAMD20E15A-MU گونجاوە بۆ 6 بەکارھێنانs: Smart Home Automation, Utility Metering, Industrial Sensor Node, Consumer Control Panel, Compact Data Acquisition Module, LED Lighting Controller.
Smart Home Automation
The ATSAMD20E15A-MU fits compact smart-home controllers that coordinate sensors, relays, and user interfaces. Its 48 MHz Cortex-M0+ core provides responsive event handling, while 32 KB of Flash stores application firmware and 4 KB of SRAM supports protocol buffers and state handling. I2C can connect temperature or ambient-light sensors, SPI can support displays or memory devices, and UART can provide a local console or gateway link. A practical design uses the serial interfaces on appropriately level-matched rails and places the MCU near the protected connector and power-entry sections of the board.
Utility Metering
The ATSAMD20E15A-MU is appropriate for metering products that acquire analog measurements and periodically report results. Its 12-bit ADC supports analog-to-digital measurement, the 48 MHz processor can perform acquisition sequencing and filtering, and UART or another serial interface can transfer records to a communications module. The 32 KB Flash provides room for calibration logic and communications routines, while 4 KB of SRAM can hold measurement and packet state. The design should verify analog input limits, acquisition timing, calibration method, and low-power behavior against the product's metering accuracy and duty-cycle requirements.
Industrial Sensor Node
The ATSAMD20E15A-MU supports small industrial sensor nodes that need local control and flexible connectivity. I2C is suitable for digital sensors, SPI supports higher-speed peripherals, and UART provides a straightforward diagnostic or uplink path. At 48 MHz, the Cortex-M0+ core can combine sensor polling, filtering, threshold evaluation, and fault reporting within one embedded platform. Its multiple low-power modes can reduce consumption between measurement events, but unused I/O states, enabled peripherals, and clock behavior must be managed carefully to avoid leakage above the intended operating budget.
Consumer Control Panel
The ATSAMD20E15A-MU can serve as the controller in a compact consumer control panel that combines local inputs, indicators, and communications. The 12-bit ADC may be used for analog input conditioning, the 10-bit DAC can provide a controlled analog level where appropriate, and UART can connect to a host or accessory. Its 32 KB Flash and 4 KB SRAM are suitable for moderate control logic rather than a large graphical user interface. Firmware should use timer-based debouncing and organized interrupt handling, while the PCB should maintain separation between sensitive analog inputs and switching or high-current output circuitry.
Compact Data Acquisition Module
The ATSAMD20E15A-MU is useful in a small data-acquisition module where measured analog values must be conditioned and transferred to another system. The 12-bit ADC performs conversion, the 48 MHz core supports scaling and basic filtering, and UART or SPI provides a host interface. Local Flash can retain configuration and firmware, while SRAM accommodates active sample and processing state. For accurate acquisition, define the input bandwidth, sample rate, reference strategy, and analog front end before firmware calibration is finalized; for communication reliability, keep the interface routing away from noisy switching nodes.
LED Lighting Controller
The ATSAMD20E15A-MU can coordinate programmable LED effects in a low-voltage lighting controller. PWM-capable outputs can drive controlled switching elements, the 48 MHz core can execute timing and animation logic, and UART or SPI can connect to a user controller or configuration memory. The 32 KB Flash is adequate for compact lighting patterns and control logic, while the 10-bit DAC can support analog setpoint generation where the design requires it. Current limits, LED-driver topology, thermal behavior, and low-power states should be engineered together so that the MCU does not exceed the thermal or switching-current limits of the lighting board.
داتای سەرچاوەی ئەندازیاری بۆ ATSAMD20E15A-MU — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ATSAMD20E15A-MUT | ATSAMD20E18A-MU | ATSAMD20E16A-MU | ATSAMD21E15A-AU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) |
| CPU Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 32 KB | 32 KB | 256 KB | 64 KB | 32 KB |
| SRAM | 4 KB | 4 KB | 32 KB | 8 KB | 4 KB |
| ADC Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| DAC Resolution | 10 bits | 10 bits | 10 bits | 10 bits | 10 bits |
جیاکەرەوە سەرەکییەکان
- Exact-family option with matched memory configuration (بەراورد بەATSAMD20E18A-MU)
- Compact integrated analog conversion (بەراورد بەATSAMD20E16A-MU)
- Direct packing-code alternative for procurement (بەراورد بەATSAMD20E15A-MUT)
تێبینییەکانی دیزاین
Configure unused GPIO and peripheral states before the product enters its lowest-power operating condition. The device supports multiple low-power modes, but unmanaged I/O states can increase leakage current above expected operating levels. Review pull states, analog-input configuration, clock gating, and peripheral enables in firmware. Confirm the supply-voltage selection against the external interface levels, and follow the manufacturer requirements for power pins, decoupling capacitance, and the exposed thermal pad.
Use the manufacturer package drawing and pin-description table to create the 32-VQFN 5 x 5 mm land pattern. Place the exposed-pad connection and thermal-via arrangement exactly as specified, and place input and output decoupling capacitors close to their associated supply pins. Keep the analog input path away from switching nodes and high-current outputs. Review the VQFN assembly requirements, including solderable area and paste pattern, before releasing the PCB for fabrication.
Do not treat every same-package SAM D20 device as an exact software substitute. ATSAMD20E18A-MU and ATSAMD20E16A-MU provide more Flash and SRAM than ATSAMD20E15A-MU, which can change the memory map, linker configuration, and firmware image. ATSAMD21E15A-AU belongs to a different family and requires a peripheral, pin-multiplexing, and clock review. A valid drop-in decision requires both the mechanical footprint and the electrical, peripheral, and software interfaces to match the intended design.
زانیاری پابەندبوون
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code.