Microchip Technology

ATTINY5-TS8R - 10MHz 8-Bit AVR Microcontroller | Microchip

MPN: ATTINY5-TS8R ✓ چالاک
SOT-23-6, 6 pins Package 10 MHz Speed 512 bytes (256 x 16 bits) Memory
MOQ: 1 |

ATTINY5-TS8R گشتی

The Microchip Technology ATTINY5-TS8R is an 8-bit AVR RISC-based CMOS microcontroller with a 10 MHz maximum clock, 512 bytes of ISP Flash memory, and 32 bytes of SRAM in a 6-pin SOT-23 package. Its compact footprint supports low-cost embedded control when a small amount of program memory and a limited I/O count are sufficient.

An 8-bit AVR microcontroller is a compact embedded-processing device that executes instructions from internal Flash memory and uses registers and SRAM for working data. The ATTINY series occupies the lower end of the AVR product hierarchy: microcontroller, embedded controller, processor, and semiconductor. Compared with larger AVR devices, its constraints require careful attention to memory usage, interrupt handling, and peripheral allocation.

Key features include four general-purpose I/O lines, 16 general-purpose working registers, a 16-bit timer/counter with two PWM channels, a four-channel 8-bit ADC, an analog comparator, and an interrupt system. The 512-byte Flash capacity is organized as 256 words of 16-bit program memory. Idle mode stops the CPU while allowing SRAM, timers, the ADC, comparator, and interrupt system to continue operating.

The device uses the AVR architecture and supports ISP programming. A programming tool connects to the target through the reset line and programming interface, making the ATTINY5 suitable for compact control products assembled with automated test equipment. Its 10 MHz operating point provides useful processing headroom for sensor reading, state-machine control, and low-duty-cycle actuator management without the complexity of a larger MCU.

Typical uses include battery-powered sensor interfaces, compact LED controllers, simple motor or valve controls, wearable accessories, and embedded household products. The ADC supports analog measurement, while dual PWM channels can drive indicators or low-power loads. For each use case, firmware should account for the limited 512-byte Flash and 32-byte SRAM before adding application functions.

PCB design requires careful decoupling and exposed-pad-free SOT-23 handling. Place the supply bypass capacitor close to VCC and GND, route programming signals away from sensitive analog inputs, and verify that the exposed copper and reflow profile match the package requirements. This page consolidates the device architecture, verified specifications, application guidance, pinout information, and same-family replacement choices for faster engineering evaluation.

جێگرەوەکانی جێگۆڕکێ بۆ ATTINY5-TS8R — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ATTINY5-TS8R (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Package, ADC, Architecture, General-Purpose Working Registers.

Microchip Technology
Product Type: 8-bit AVR microcontroller
Package: SOT-23-6
Architecture: AVR enhanced RISC
بەراوردکردن لەگەڵ ATTINY5-TS8R →
Microchip Technology
Product Type: 8-bit AVR RISC-based microcontroller
Package: SOT-23-6
ADC: Internal analog-to-digital converter
بەراوردکردن لەگەڵ ATTINY5-TS8R →

ATTINY10-TS8R

✅ جێگرەوەی ڕاستەوخۆ
📦 SOT-23-6
ATtiny10 provides more Flash memory than the ATTINY5's 512 bytes, while retaining the 8-bit AVR architecture, 10 MHz-class operation, and SOT-23-6 footprint

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

ATTINY4-TS8R

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 SOT-23-6
8-bit AVR microcontroller · AVR enhanced RISC · 512 bytes flash, organized as 256 x 16 · 32 bytes SRAM · 10 MHz · 4 · Internal oscillator · SOT-23-6

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATTINY9-TSHR

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 SOT-23-6
8-bit AVR RISC-based microcontroller · 1 KB (512 x 16) · ISP Flash · 32 x 8 bytes · 4 · 16 · 12 MHz · 16-bit with two PWM channels

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATTINY5-TSHR

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 SOT-23-6
8-bit AVR RISC microcontroller · 512 bytes (256 x 16) · ISP flash · 32 bytes (32 x 8 bits) · 12 MHz · 1.8 V to 5.5 V DC · 4 lines · 16 registers

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ATTINY5-TS8R زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type 8-bit AVR RISC-based CMOS microcontroller
زۆرترین فرێکوێنسیی کاتژمێر 10 MHz
Flash Memory 512 bytes (256 x 16 bits)
SRAM 32 bytes
General-Purpose Working Registers 16 registers
General-Purpose I/O Lines 4 lines
Timer/Counter 16-bit timer/counter with 2 PWM channels
ADC 4-channel, 8-bit ADC
Analog Comparator 1 analog comparator
Architecture AVR 8-bit RISC
Program Memory Type ISP Flash
Programming Interface In-Circuit Serial Programming (ICSP)
پاکێج SOT-23-6, 6 pins
جۆری دامەزراندن Surface mount
دۆخی RoHS Unknown
REACH Status Unknown
AEC-Q100 Qualification Unknown

ڕێکخستنی پینی ATTINY5-TS8R

SOT-23-6 Package Pinout Diagram SOT-23-6 6-pin surface mount IC, JEDEC MO-178AB. Pin 1 by dot. 1 2 3 4 5 6 SOT-23-6
پین 1 PB4 — General-purpose input/output pin 4
پین 2 PB3 — General-purpose input/output pin 3
پین 3 PB2 — General-purpose input/output pin 2
پین 4 PB1 — General-purpose input/output pin 1
پین 5 GND — Ground reference
پین 6 VCC — Supply voltage input

بەکارهێنانە باوەکان

ATTINY5-TS8R گونجاوە بۆ 6 بەکارھێنانs: Battery-Powered Sensor Interface, LED Dimming and Indicator Control, Compact Motor or Valve Controller, Low-Power Household Control Module, Programmable Threshold Detector, Wearable or Portable Accessory Controller.

🧩

Battery-Powered Sensor Interface

The ATTINY5-TS8R fits compact battery-powered sensor interfaces that require periodic analog measurement and limited digital logic. Its four-channel 8-bit ADC can sample sensor conditions, while the 10 MHz 8-bit AVR core handles thresholding, filtering, and state-machine updates. The 512-byte Flash limit supports small, focused firmware, and the 32-byte SRAM requires careful buffer sizing. According to the Microchip manufacturer information, Idle mode stops the CPU while retaining timer, ADC, comparator, SRAM, and interrupt operation, enabling duty-cycled measurements with reduced active time. Use the timer to schedule conversions, disable unused port inputs to limit leakage, and validate the average current against the sensor's own standby demand.

💡

LED Dimming and Indicator Control

The ATTINY5-TS8R is appropriate for simple LED dimming, status indication, and periodic signaling designs. Its 16-bit timer/counter with two PWM channels can generate modulation outputs without relying on software timing loops, and the four general-purpose I/O lines provide enough external control for a compact indicator assembly. The 8-bit ADC can also be used for ambient-light measurement when a light-dependent divider is present. According to the Microchip ATtiny5 product page, the device includes two PWM channels and four I/O lines. Keep PWM outputs on the PB pins assigned by the package pinout, account for LED current in the external driver stage, and use resistor values that keep the port current within the device's electrical limits.

🏭

Compact Motor or Valve Controller

The ATTINY5-TS8R can serve as the supervisory controller in a low-duty-cycle motor, pump, latched-valve, or actuator design. Its timer/counter supports timed state transitions, while the comparator can monitor a feedback signal and the ADC can read a sensor or supply condition. Because only four I/O pins are available, external drive transistors or an interface driver are usually necessary rather than connecting a load directly to a GPIO. According to the Microchip manufacturer documentation, the comparator and timer continue operating during Idle mode, which is useful when the controller must wake periodically or respond asynchronously. Add flyback protection for inductive loads, keep switching edges away from the ADC input, and include a defined safe state for every startup and fault condition.

🏠

Low-Power Household Control Module

The ATTINY5-TS8R is well suited to compact household controls such as switch interfaces, appliance sensors, and simple timer modules. Four I/O lines can operate a small user interface or read discrete inputs, while the 8-bit ADC provides basic analog supervision. The 512-byte program memory favors a narrowly defined product function rather than a general-purpose control platform. According to the Microchip ATtiny5 family information, the device includes Idle mode with continued timer, ADC, comparator, SRAM, and interrupt-system operation. This allows the MCU to remain responsive without keeping the CPU active continuously. Use a dedicated pull-up or pull-down strategy for every control input, minimize external leakage, and verify that the power supply remains within the device's specified operating range.

🔧

Programmable Threshold Detector

The ATTINY5-TS8R can implement a configurable threshold or alarm detector by combining analog measurement with internal timing and digital output control. The four-channel 8-bit ADC supports multiple sensor inputs, and the analog comparator provides a hardware threshold function that can complement software comparison. According to the Microchip manufacturer information, both the comparator and ADC remain available during Idle mode, allowing the device to monitor a condition while reducing CPU activity. Firmware can then debounce the event, apply hysteresis, and activate an indicator or alarm output. The limited 512-byte Flash and 32-byte SRAM favor storing calibration values economically and processing samples one at a time. Validate thresholds across temperature and supply variation before using the output for safety-related action.

📱

Wearable or Portable Accessory Controller

The ATTINY5-TS8R is useful in wearable accessories and compact portable products where a six-pin footprint, low component count, and event-driven operation are important. A button, motion input, or simple sensor can trigger firmware that drives an LED, haptic element, or digital interface through external circuitry. The 10 MHz AVR core provides more than enough throughput for a small control loop, while the 512-byte Flash space supports concise event handling. According to the Microchip ATtiny5 manufacturer documentation, Idle mode can preserve timer, comparator, ADC, SRAM, and interrupt behavior with the CPU stopped. This helps reduce average energy use in accessories that remain connected to power for long periods. Keep unused pins in defined states and confirm that any expansion connector does not compromise the required analog accuracy.

What are the key specifications of ATTINY5-TS8R that engineers should know?
The ATTINY5-TS8R is a 10 MHz, 8-bit AVR microcontroller with 512 bytes of ISP Flash, 32 bytes of SRAM, four general-purpose I/O lines, and a 6-pin SOT-23 package. According to the Microchip ATtiny5 manufacturer datasheet and product page, it also includes a four-channel 8-bit ADC, a 16-bit timer/counter with two PWM channels, an analog comparator, and 16 working registers. Its main design constraint is memory capacity, so firmware should be budgeted around the 256-word program space and limited SRAM.
Where can I download the ATTINY5-TS8R datasheet PDF?
The authoritative ATTINY5-TS8R documentation is available through the Microchip ATtiny5 product page, which links to the manufacturer datasheet and supporting device documentation. The ATTINY5-TS8R ordering code identifies the SOT-23-6 package variant of the ATtiny5 family. According to Microchip, the device supports In-Circuit Serial Programming through dedicated programming connections. Use the Microchip datasheet for the definitive pin description, electrical limits, clock requirements, and programming information before laying out a new PCB.
Where is the ATTINY5 pinout and what does each pin do?
The ATTINY5-TS8R uses a 6-pin SOT-23 layout with four I/O pins, ground, and supply. According to the Microchip manufacturer pinout, pin 1 is PB4, pin 2 is PB3, pin 3 is PB2, pin 4 is PB1, pin 5 is GND, and pin 6 is VCC. ICSP programming uses the reset and programming interface associated with the device. Keep the package pin numbering visible during PCB layout and confirm signal assignments against the current Microchip datasheet.
How do I program the ATTINY5-TS8R?
The ATTINY5-TS8R is programmed through In-Circuit Serial Programming, or ICSP. According to the Microchip ATtiny5 product page, the programmer connects to the target using a High-Speed USB 2.0 interface through an 8-pin SIL connector, with target-side connections to I/O and reset signals. Typical tooling includes a Microchip-supported programmer and development environment. Firmware must also remain within the device's 512-byte Flash limit, so concise machine code and compact application logic are important.
What can replace ATTINY5-TS8R?
ATTINY4-TS8R, ATTINY10-TS8R, and ATTINY9-TSHR are the closest same-family alternatives identified for the ATTINY5-TS8R, although firmware and pin-function requirements must be revalidated before substitution. According to the family comparison pages, ATTINY4-TS8R has less Flash memory, while ATTINY10-TS8R provides more Flash memory. These are compact 8-bit AVR devices in the same SOT-23-6 family, but a PCB change or firmware adjustment should be expected when memory capacity or peripheral behavior differs.
Is ATTINY5-TS8R the same as ATTINY10-TS8R?
No. Both devices are compact 8-bit AVR microcontrollers in the SOT-23-6 package, but ATTINY10-TS8R provides more program memory than the ATTINY5-TS8R. According to the Microchip ATtiny5 family information and published comparison data, the ATTINY5 has 512 bytes of Flash and 32 bytes of SRAM. ATTINY10-TS8R is best considered a same-footprint family alternative, not an identical part. Review memory usage, ADC behavior, interrupts, and programming requirements before approving it as a replacement.
ATTINY5-TS8R vs ATTINY10-TS8R: which is better for a compact controller?
Choose ATTINY5-TS8R when 512 bytes of Flash and 32 bytes of SRAM are sufficient; choose ATTINY10-TS8R when the firmware needs more program memory while retaining a compact 8-bit AVR implementation. According to published ATtiny family comparisons, both parts use an 8-bit AVR core and a 10 MHz-class SOT-23-6 implementation. The decision should be based primarily on compiled firmware size, SRAM demand, peripheral requirements, and qualification needs rather than package size alone.
What is the difference between ATTINY5-TS8R and ATTINY4-TS8R?
The principal documented difference is Flash-memory capacity: ATTINY5-TS8R provides 512 bytes, while ATTINY4-TS8R provides less program memory. Both belong to the compact 8-bit AVR family and use the SOT-23-6 package. According to family comparison data, ATTINY4-TS8R is the better candidate when minimal firmware is acceptable and lower memory use is desirable. Do not replace the ATTINY5 without checking the compiled code size, SRAM requirements, and any ADC or peripheral dependencies.
When should I choose ATTINY5-TS8R over ATTINY10-TS8R?
Choose ATTINY5-TS8R over ATTINY10-TS8R when a compact design needs 512 bytes of Flash, 32 bytes of SRAM, four I/O lines, a four-channel 8-bit ADC, and two PWM outputs without requiring additional program memory. According to the Microchip ATtiny5 family information, its resources are sufficient for simple state machines, sensor sampling, and low-duty-cycle control. Select ATTINY10-TS8R instead when the compiled firmware exceeds the ATTINY5 program space or requires more memory headroom.
Is ATTINY5-TS8R suitable for battery-powered sensor applications?
The ATTINY5-TS8R is suitable for many battery-powered sensor applications because its 8-bit core, 512-byte Flash memory, 32-byte SRAM, and four I/O lines support compact control functions. According to the Microchip manufacturer documentation, Idle mode stops the CPU while allowing SRAM, the timer/counter, ADC, analog comparator, and interrupt system to continue functioning. Power consumption still depends on the selected clock, sleep strategy, ADC duty cycle, pull networks, and external sensor current.
How much power does the ATTINY5-TS8R consume?
The ATTINY5-TS8R includes an Idle mode that stops the CPU while retaining timer, ADC, comparator, SRAM, and interrupt operation. According to the Microchip manufacturer datasheet, current consumption depends on operating mode, clock configuration, analog activity, port state, and supply voltage. Use the datasheet active, idle, and power-down operating-current tables for numerical design limits. For a battery budget, calculate the average current from the duty cycle of active conversion, processing, and sleep intervals.
Can ATTINY5-TS8R drive PWM outputs?
Yes. The ATTINY5-TS8R includes a 16-bit timer/counter with two PWM channels, according to the Microchip ATtiny5 product page. This is useful for LED brightness control, simple motor-speed modulation, or generating a periodic control signal without software timing loops. The four PB port pins are shared with other functions, so assign PWM outputs against the device pinout and verify whether the ADC or comparator also needs those pins.
Where can I buy ATTINY5-TS8R and how do I request current pricing?
Use the Request a Quote form on this page to request current ATTINY5-TS8R pricing, stock status, lead time, and order quantities. The manufacturer identifies the exact device as a 512-byte-Flash, 8-bit, 10 MHz AVR microcontroller in a SOT-23-6 package. Commercial terms can change independently of technical documentation, so request a written quotation against the exact ATTINY5-TS8R ordering code rather than substituting another package or temperature-grade suffix.
What is the lead time for ATTINY5-TS8R?
The current lead time for ATTINY5-TS8R should be requested through the Request a Quote form on this page. Manufacturing availability can vary by order quantity, package form, date code, and regional logistics conditions. Microchip identifies ATTINY5-TS8R as an active SOT-23-6 ordering code, but active lifecycle status does not by itself guarantee immediate stock. Request the current schedule and minimum order quantity before committing the production build.
Is ATTINY5-TS8R in stock?
Use the Request a Quote form on this page for an ATTINY5-TS8R stock check tied to the required quantity. The device is listed as active, while current availability can change with procurement activity and requested packaging configuration. Ask the supplier to confirm the exact manufacturer part number, package suffix, quantity, date code, and shipment origin. Do not treat a catalog listing or family-level inventory statement as a firm allocation for the ATTINY5-TS8R.
What is the best Microchip equivalent for ATTINY5-TS8R?
The closest identified Microchip alternatives are ATTINY10-TS8R for more Flash memory, ATTINY4-TS8R for reduced program memory, and ATTINY9-TSHR as another SOT-23-6 family option. According to Microchip family comparison information, the ATTINY5 has 512 bytes of Flash, 32 bytes of SRAM, four I/O lines, and a four-channel 8-bit ADC. No verified cross-manufacturer drop-in equivalent was identified, so a replacement decision should emphasize pin functions, firmware size, SRAM, and peripheral requirements.

داتای سەرچاوەی ئەندازیاری بۆ ATTINY5-TS8R — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose ATTINY5-TS8R for a small embedded product that fits within 512 bytes of Flash and 32 bytes of SRAM but benefits from a four-channel 8-bit ADC, a comparator, and two PWM outputs. Its SOT-23-6 package is useful when board area is constrained. Choose ATTINY10-TS8R when the compiled application needs more program memory, and choose ATTINY4-TS8R when the final firmware is small enough to fit comfortably within its lower Flash capacity. ATTINY9-TSHR is a same-family option with more program memory, while ATTINY5-TSHR provides the closest electrical match within the same package. ATTINY48-AUR and ATTINY88-MUR are better when additional I/O, memory, or application logic outweigh the benefit of the six-pin footprint. Before replacing the ATTINY5, verify pin functions, memory headroom, SRAM use, peripheral behavior, programming compatibility, temperature requirements, and lifecycle status.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ATTINY10-TS8R ATTINY4-TS8R ATTINY9-TSHR ATTINY5-TSHR
Package SOT-23-6 SOT-23-6 - same SOT-23-6 - same SOT-23-6 - same SOT-23-6 - same
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Core 8-bit AVR 8-bit AVR 8-bit AVR 8-bit AVR 8-bit AVR
Flash Memory 512 bytes 1 KB 256 bytes 1 KB 512 bytes
General-Purpose I/O 4 lines 4 lines 4 lines 4 lines 4 lines

جیاکەرەوە سەرەکییەکان

  • Balanced memory and peripheral allocation (بەراورد بەATTINY4-TS8R)
  • Four-channel 8-bit ADC for compact analog control (بەراورد بەATTINY4-TS8R)
  • Compact six-pin implementation (بەراورد بەATTINY48-AUR)
  • Timer-based PWM without a larger MCU (بەراورد بەATTINY20-UUR)

تێبینییەکانی دیزاین

Place the VCC bypass capacitor immediately between pins 6 and 5, with the ground connection using the shortest possible path to the supply return plane. The SOT-23-6 footprint leaves little routing space, so reserve the PB pins used by programming and analog measurement before placing the remaining circuitry. Keep sensitive ADC inputs away from PWM outputs and programming signals. Confirm the exposed-pad treatment, land pattern, solder mask, and reflow profile against the current Microchip package drawing.

The ATTINY5-TS8R is intended for compact embedded products, but active current still contributes to the average battery load. Calculate the operating budget from processor-active time, ADC conversion intervals, comparator use, timer wakeups, and the duration of Idle mode. According to the Microchip manufacturer information, Idle mode stops the CPU while allowing SRAM, timers, the ADC, the comparator, and the interrupt system to continue operating. Set unused port pins to defined levels, remove unnecessary external loads, and confirm the chosen regulator maintains the required supply voltage throughout switching transitions.

The most consequential constraint is the ATTINY5's 512-byte Flash and 32-byte SRAM capacity. Compile the complete firmware before committing to the part, because interrupt vectors, library routines, and application code can consume a large share of a small program image. Avoid recursive routines and large buffered data structures, and test stack headroom with representative interrupts enabled. When evaluating a replacement, review the compiled code size, SRAM demand, ADC channels, timer behavior, and package pin functions rather than relying only on the SOT-23-6 outline.

Separate analog sensing from the digital control and programming paths. Route PB4 and PB3, which can carry sensitive analog functions, with short traces and a quiet ground reference. Place the analog input network near the package and away from the switching node of any external actuator driver. For designs combining PWM and ADC measurements, test settling after a PWM edge and sample during a stable interval. These layout practices help preserve the useful resolution of the four-channel 8-bit converter without changing the external component count.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No device-specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact ATTINY5-TS8R ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

attiny5 datasheet attiny5 pinout attiny5 programming attiny5 arduino ATTINY5-TS8R datasheet pdf ATTINY5-TS8R pinout ATTINY5-TS8R specifications ATTINY5-TS8R equivalent ATTINY5-TS8R replacement ATTINY5-TS8R vs ATTINY10-TS8R ATTINY5-TS8R price ATTINY5-TS8R stock Microchip ATTINY5-TS8R ATTINY5 SOT-23-6 application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology ATTINY5-TS8R ATTINY5 ATTINY10-TS8R ATTINY4-TS8R ATTINY9-TSHR ATTINY5-TSHR ATTINY48-AUR ATTINY20-UUR ATTINY88-MUR AVR 8-bit RISC microcontroller embedded microcontroller semiconductor ISP Flash In-Circuit Serial Programming ICSP SOT-23-6 SOT-23 surface-mount package four-channel 8-bit ADC analog comparator 16-bit timer/counter PWM Idle mode operating voltage battery-powered sensor interface
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ