ATXMEGA8E5-AU - 32MHz 8KB AVR MCU | Microchip Technology
MPN: ATXMEGA8E5-AU ✓ چالاکATXMEGA8E5-AU گشتی
An AVR XMEGA microcontroller is a compact embedded-control device that combines a CPU core, flash program memory, SRAM, EEPROM, timers, communication peripherals, and event-system hardware on one integrated circuit. The ATXMEGA8E5 belongs to the low-power, high-performance XMEGA E5 family, where the enhanced RISC architecture supports deterministic embedded processing for control, sensing, communications, and low-energy products.
The device provides 8 KB of ISP Flash organized as 4K × 16, plus a 2 KB boot-code section with read-while-write capabilities. Its memory resources include 512 bytes of EEPROM and 1 KB of SRAM. An eight-channel event system connects peripherals without requiring continuous CPU intervention, while a programmable multi-level interrupt system supports event-driven firmware designs. A maximum clock frequency of 32 MHz provides additional performance headroom for compact control tasks.
The ATXMEGA8E5-AU is intended for embedded systems that need deterministic peripheral interaction, efficient local storage, and a compact surface-mount footprint. Potential uses include industrial control modules, low-power sensor nodes, compact motor-control subsystems, building automation, instrumentation, and compact consumer accessories. The 1.6 V minimum operating voltage also makes the device suitable for systems designed around low-voltage energy-storage or sensor-power rails.
Designers should pay attention to the 1.6 V to 3.6 V supply range, available 1 KB SRAM, and the division between 8 KB general Flash and the 2 KB boot section. Firmware size and interrupt-heavy workloads should be checked against the limited SRAM. Decoupling, clock stability, programming access, and exposed-pad or via-in-pad land patterns should be reviewed against the complete manufacturer data sheet before layout release.
This page consolidates the verified manufacturer and distributor specifications, focused drop-in comparison data, and practical engineering guidance for the ATXMEGA8E5-AU. It also distinguishes verified electrical and packaging facts from parameters that require confirmation in the complete Microchip documentation.
جێگرەوەکانی جێگۆڕکێ بۆ ATXMEGA8E5-AU — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ATXMEGA8E5-AU (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, SRAM, Boot Code Section, EEPROM, Product Type.
ATXMEGA8E5-M4U
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATXMEGA8E5-M4UR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATXMEGA8E5-MU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATXMEGA16E5-AU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATXMEGA32E5-AU
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ATXMEGA8E5-AU زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 8/16-bit RISC Microcontroller |
| CPU Architecture | AVR enhanced RISC |
| Product Family | AVR XMEGA E5 |
| Maximum CPU Frequency | 32 MHz |
| ڤۆڵتاژی دابینکردنی کارکردن | 1.6 V to 3.6 V |
| Flash Memory | 8 KB (4K × 16) |
| Boot Code Section | 2 KB |
| Read-While-Write Support | Yes |
| EEPROM | 512 bytes |
| SRAM | 1 KB |
| Event System | 8 channels |
| Programmable Multi-Level Interrupt | Yes |
| پاکێج | 32-pin TQFP (7 mm × 7 mm) |
| جۆری دامەزراندن | Surface Mount |
| Temperature Grade | Industrial temperature |
| Environmental Packaging | Green |
ڕێنمایی ڕێکخستنی پینی ATXMEGA8E5-AU 32-pin tqfp (7 mm × 7 mm)
ڕێکخستنی پین بۆ ATXMEGA8E5-AU (پاکێجی 32-pin tqfp (7 mm × 7 mm)). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ ATXMEGA8E5-AU.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
ATXMEGA8E5-AU گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor and Control Module, Low-Power Environmental Sensor Node, Compact Motor and Valve Control, Building Automation Endpoint, Portable Measurement Instrument, Consumer Accessory Controller.
Industrial Sensor and Control Module
The ATXMEGA8E5-AU fits compact industrial sensing modules that combine a 32 MHz AVR processor with deterministic peripheral event handling. Its 1.6 V to 3.6 V operating range supports low-voltage sensor and control rails, while the eight-channel event system can connect timers and I/O events without continuous polling. The 8 KB Flash and 1 KB SRAM are sufficient for focused acquisition, thresholding, and actuator logic, provided the firmware avoids unnecessarily large buffers. Designers should reserve memory for stack growth and verify regulator tolerance during motor or relay transients.
پێشنیارکراو
Low-Power Environmental Sensor Node
The ATXMEGA8E5-AU is appropriate for a compact environmental sensor node that must sample inputs and update communications or local indicators while minimizing unnecessary processing. Its low 1.6 V minimum supply voltage provides flexibility for energy-harvesting front ends and low-voltage sensor systems, while the event system supports responsive timer-based sampling. The 1 KB SRAM may be adequate for small sample windows, but engineers should avoid deep buffering and confirm sleep-mode current and wake-up behavior in the manufacturer data sheet before calculating battery life.
پێشنیارکراو
Compact Motor and Valve Control
The ATXMEGA8E5-AU can serve as the supervisory controller in a compact motor, valve, or actuator subsystem where multiple timers and peripheral events must be coordinated. Its maximum 32 MHz clock provides timing headroom, and the eight-channel event system can connect counters, timers, and I/O events with less CPU polling than a simpler polled design. The 8 KB program-memory limit favors concise control firmware, while the 1 KB SRAM requires careful allocation for motion state. External drivers, protection networks, and fault handling must remain separate from the MCU.
پێشنیارکراو
Building Automation Endpoint
The ATXMEGA8E5-AU suits a low-cost building-automation endpoint that monitors switches or sensors and controls lighting, HVAC, or access functions over a local bus. Its 8/16-bit AVR architecture and 32 MHz operating limit provide adequate performance for protocol handling and debounce logic, while its compact 32-pin TQFP footprint supports dense controller boards. The 1.6 V to 3.6 V range simplifies integration with low-voltage power trees, but external transceivers and isolation may determine the final operating voltage. Firmware and memory use should be checked against protocol-stack overhead.
پێشنیارکراو
Portable Measurement Instrument
The ATXMEGA8E5-AU can support a compact measurement instrument that converts sensor signals into local readings, calibration values, or status information. Its 32 MHz clock supports moderately responsive control and measurement sequencing, while read-while-write capability can simplify nonvolatile program-memory operations. The 1 KB SRAM is suitable for small working sets but not large waveform acquisition, so streamed data should be sent directly to external storage or communications hardware. A precision analog front end and regulator remain necessary for accurate measurement performance.
پێشنیارکراو
Consumer Accessory Controller
The ATXMEGA8E5-AU fits compact consumer accessories that combine touch or switch input, LED indication, and a simple serial interface. Its event system helps implement responsive button handling and periodic tasks without continuous register polling, while its 1.6 V to 3.6 V range can support low-voltage product rails. The 8 KB Flash and 1 KB SRAM constrain application complexity, making the MCU most suitable for focused embedded products rather than graphical or connectivity-heavy systems. Firmware updates should use the available boot section and follow the manufacturer programming procedure.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ ATXMEGA8E5-AU — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | ATXMEGA8E5-M4U | ATXMEGA8E5-M4UR | ATXMEGA8E5-MU | ATXMEGA16E5-AU | ATXMEGA32E5-AU |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP (7x7) | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same | 32-TQFP (7x7) - same |
| CPU Frequency | 32 MHz maximum | 32 MHz maximum | 32 MHz maximum | 32 MHz maximum | 32 MHz maximum | 32 MHz maximum |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB | 16 KB | 32 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 2 KB | 4 KB |
| EEPROM | 512 bytes | 512 bytes | 512 bytes | 512 bytes | 1 KB | 1 KB |
| Boot Code Section | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 4 KB |
| Architecture | AVR enhanced RISC, 8/16-bit | AVR enhanced RISC, 8/16-bit | AVR enhanced RISC, 8/16-bit | AVR enhanced RISC, 8/16-bit | AVR enhanced RISC, 8/16-bit | AVR enhanced RISC, 8/16-bit |
جیاکەرەوە سەرەکییەکان
- Smallest Flash configuration in the compared XMEGA E5 set (بەراورد بەATXMEGA16E5-AU)
- Lower SRAM requirement than the larger E5 alternatives (بەراورد بەATXMEGA32E5-AU)
- Common 32 MHz AVR XMEGA architecture (بەراورد بەATXMEGA8E5-MU)
- Lower flash capacity with a defined 2 KB boot-code area (بەراورد بەATXMEGA32E5-AU)
تێبینییەکانی دیزاین
Design the supply for the verified 1.6 V to 3.6 V operating range and place the recommended decoupling capacitors close to the corresponding ATXMEGA8E5-AU power and ground pins. Keep switching-regulator and high-current load paths away from sensitive return-current paths. Because the verified records do not provide the complete absolute-maximum or power-consumption tables, confirm voltage tolerance, startup behavior, and current limits in the manufacturer data sheet before releasing the power network.
Use the official 32-pin TQFP land pattern and verify the mechanical drawing for the exact ordering suffix. Route the clock circuit over a continuous ground reference and keep programming, reset, and high-impedance signal paths short and free of nearby switching nodes. Preserve accessible test points for supply, ground, reset, and programming signals so production diagnostics and firmware updates do not require PCB modifications.
Do not base firmware capacity only on the 8 KB Flash headline: reserve the separate 2 KB boot-code section as required by the application and account for bootloader, interrupt-vector, and application-storage requirements. Also monitor the 1 KB SRAM limit, especially when combining protocol parsing with buffered sampling. Validate the final linker map, worst-case stack depth, watchdog behavior, and brownout settings before production release.
A larger XMEGA E5 device may fit the same family and 32-pin platform but can have materially different Flash, SRAM, EEPROM, boot-section, power-consumption, and peripheral differences. When substituting ATXMEGA16E5-AU or ATXMEGA32E5-AU, recheck memory maps, peripheral availability, timing assumptions, package drawings, and firmware startup code. A mechanically similar package alone does not establish complete application compatibility.
زانیاری پابەندبوون
The verified distributor snippets identify the ATXMEGA8E5-AU as a green industrial-temperature part, and one third-party listing describes the component as RoHS-compliant and lead-free. Because the authoritative manufacturer product extract supplied here does not explicitly state compliance results, the remaining compliance fields remain unknown rather than being inferred.