Infineon

CY7C65215A-32LTXI - 12Mbps USB Dual Serial Bridge | Infineon

MPN: CY7C65215A-32LTXI ✓ چالاک
1 integrated voltage regulator Vdss 32-QFN, 5x5 mm Package 1 integrated flash-memory block Memory
MOQ: 1 |

CY7C65215A-32LTXI گشتی

Infineon Technologies CY7C65215A-32LTXI is a USB-serial dual-channel bridge controller with UART, I2C, and SPI interfaces, 12 Mbps USB 2.0 operation, CAPSENSE touch sensing, and Battery Charging Detection in a 32-QFN 5x5 mm package. It provides a compact interface between a USB host and embedded serial peripherals.

A USB-serial bridge controller is an interface IC that translates USB traffic into UART, I2C, or SPI transactions. These devices simplify host connectivity by eliminating a host-side USB protocol stack and by presenting a familiar peripheral interface to the target circuit. The CY7C65215/CY7C65215A family combines full-speed USB control, serial interface conversion, configuration storage, and peripheral power-management functions in one integrated device.

Key features include support for dual-channel UART, I2C, or SPI operation, a maximum USB data rate of 12 Mbps, and integration of CAPSENSE and Battery Charging Detection. The battery-charging function complies with USB Battery Charging Specification Revision 1.2. Internal voltage-regulator, oscillator, and flash-memory blocks provide the core resources required for configuration and peripheral control without requiring separate storage for operating parameters.

The controller supports both bus-powered and self-powered USB devices. Suspend and remote-wake-up signals improve power management when a connected peripheral is idle. The A designation distinguishes this device revision, while the -32LTXI ordering code identifies the 32-pin lead-free temperature and package configuration used in the product listing.

Typical uses include USB-to-UART and USB-to-I2C adapters, industrial serial gateways, configuration ports, capacitive-control interfaces, and embedded systems that need to enumerate through USB while communicating internally through UART, I2C, or SPI. The integrated CAPSENSE function can also support touch-sensitive controls in human-interface equipment.

PCB design should preserve short USB traces, provide a continuous ground reference, and place decoupling and configuration-programming components near the appropriate pins. Because the bridge coordinates USB enumeration, serial timing, and configuration storage, verify suspend behavior, wake-up requirements, and signal levels across the complete host-device connection.

This product page combines manufacturer interface and packaging details with application-specific guidance, design considerations, and a same-footprint comparison. The comparison highlights the limited availability of true drop-in alternatives, avoiding the inclusion of electrically similar devices that require a different footprint or PCB redesign.

جێگرەوەکانی جێگۆڕکێ بۆ CY7C65215A-32LTXI — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ CY7C65215A-32LTXI (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Battery Charging Detection, Integrated Oscillator, Integrated Voltage Regulator, USB Standard, Integrated Flash Memory.

Infineon
Battery Charging Detection: BCD compliant with USB Battery Charging Specification Revision 1.2
Integrated Oscillator: Integrated
Integrated Voltage Regulator: Integrated
بەراوردکردن لەگەڵ CY7C65215A-32LTXI →
Infineon
Battery Charging Detection: USB Battery Charging Specification Rev. 1.2 compatible
Integrated Oscillator: Integrated
Integrated Voltage Regulator: Integrated
بەراوردکردن لەگەڵ CY7C65215A-32LTXI →

CY7C65215-32LTXI

✅ جێگرەوەی ڕاستەوخۆ
Infineon
📦 32-QFN (5x5 mm)
Dual-channel USB-serial bridge controller · USB 2.0 · 12 Mbps · 2 channels · UART, I2C, and SPI · 1.71 V to 5.5 V · CapSense · BCD compliant with USB Battery Charging Specification Revision 1.2

پەیوەندی بۆ نرخ

بینینی داتاشیت →

CY7C65215A-32LTXI تایبەتمەندییەکان

Device Type USB-serial dual-channel bridge controller
USB Standard USB 2.0 full-speed
Maximum USB Data Rate 12 Mbps
Serial Interfaces UART, I2C, and SPI
Serial Channel Count 2 channels
Integrated Touch Sensing CAPSENSE function
Battery Charging Detection BCD function
Battery Charging Compliance USB Battery Charging Specification Revision 1.2
Integrated Voltage Regulator 1 integrated voltage regulator
Integrated Oscillator 1 integrated oscillator
Integrated Flash Memory 1 integrated flash-memory block
Power Modes Bus-powered and self-powered modes
Power Management Features Suspend and remote wake-up signals
پاکێج 32-QFN, 5x5 mm
ژمارەی پین 32 pins
جۆری دامەزراندن Surface mount
پلەی گەرمیی کارکردن Up to 85 degrees C
دۆخی RoHS Compliant

ڕێنمایی ڕێکخستنی پینی CY7C65215A-32LTXI 32-qfn, 5x5 mm

ڕێکخستنی پین بۆ CY7C65215A-32LTXI (پاکێجی 32-qfn, 5x5 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 32-qfn, 5x5 mm بۆ CY7C65215A-32LTXI

هیچ داتای وردی پینئاوت بەردەست نییە بۆ CY7C65215A-32LTXI.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

CY7C65215A-32LTXI گونجاوە بۆ 6 بەکارھێنانs: USB-to-I2C Configuration Gateway, USB-to-UART Debug Adapter, SPI Peripheral Bridge, Capacitive Touch USB Peripheral, USB Battery-Charging Detection Adapter, Industrial USB Serial Gateway.

🌐

USB-to-I2C Configuration Gateway

The CY7C65215A-32LTXI fits compact USB-to-I2C gateways because one controller provides a full-speed USB host connection and a configurable serial peripheral channel. Its listed USB rate of up to 12 Mbps is suitable for command exchange, configuration transfers, and status polling when the connected I2C peripheral is not the limiting factor. The integrated flash stores configuration parameters, while the internal voltage regulator and oscillator reduce the number of supporting components. In a gateway design, keep the USB and I2C routing separated, provide local decoupling, and define how the host restarts or re-enumerates the device after configuration changes.

🔧

USB-to-UART Debug Adapter

A USB-to-UART debug adapter benefits from the CY7C65215A-32LTXI because the device combines a USB full-speed peripheral interface with a configurable UART channel in a 32-QFN 5x5 mm package. The bridge can enumerate over USB while exposing a conventional serial path to a microcontroller, FPGA, or programmable controller. Its integrated configuration flash supports persistent operating parameters, and the regulator and oscillator are integrated into the same package. Designers should verify logic levels, baud-rate support, flow-control requirements, and suspend behavior before connecting the adapter to the target circuit.

🖥️

SPI Peripheral Bridge

The CY7C65215A-32LTXI can serve as a USB-to-SPI bridge in embedded systems where a host computer must access registers, sensors, flash devices, or other SPI peripherals. The controller supports SPI as one of its configurable serial interfaces and operates as a USB 2.0 full-speed peripheral at up to 12 Mbps. Configuration flash allows operating parameters to be retained across sessions, reducing repeated host setup. For reliable SPI operation, account for signal polarity, clock phase, transfer rate, and device-select behavior in the host software, and keep high-speed SPI traces short and properly referenced.

🧩

Capacitive Touch USB Peripheral

The integrated CAPSENSE function makes the CY7C65215A-32LTXI useful in USB human-interface and control peripherals that combine data communication with capacitive touch inputs. A host can enumerate the controller over USB while the CAPSENSE section evaluates touch or proximity behavior and the serial interface exchanges control data. The 32-QFN 5x5 mm package supports compact board layouts, while the integrated regulator, oscillator, and flash reduce external component count. Follow the manufacturer's sensor-layout and calibration guidance because trace geometry, grounding, shield structure, and environmental coupling directly affect touch performance.

📱

USB Battery-Charging Detection Adapter

The CY7C65215A-32LTXI fits adapters and portable-device interface boards that need USB Battery Charging Specification Revision 1.2 detection alongside serial connectivity. Battery Charging Detection is integrated with the full-speed USB controller and dual-channel UART, I2C, or SPI interface, allowing a compact design to enumerate, identify charging conditions, and exchange data with a portable device. The controller also supports bus-powered and self-powered operating modes. Designers should define the power path separately from data signaling, validate the charging policy with the target device, and ensure the implementation follows the cited battery-charging specification.

🏭

Industrial USB Serial Gateway

The CY7C65215A-32LTXI is suited to industrial gateways that connect USB service ports to embedded UART, I2C, or SPI subsystems. The 12 Mbps full-speed USB connection supports administrative data transfer, while dual-channel serial connectivity and persistent configuration simplify integration into compact controller boards. Remote wake-up and suspend functions can support controlled power states, and the integrated flash retains setup data. For industrial deployment, add appropriate electrical protection, isolation where required, robust grounding, and enclosure temperature design. The stated 85-degree-C maximum temperature should be checked against the installed ambient and self-heating conditions.

کورتەی بەرهەمە پێشنیارکراوەکان

SP3232EET-L/TR MaxLinear بەکارهێنراوە لە: USB-to-I2C Configuration Gateway USB2412-DZK-TR Microchip Technology بەکارهێنراوە لە: USB-to-I2C Configuration Gateway ISO1042BDWR Texas Instruments بەکارهێنراوە لە: USB-to-I2C Configuration Gateway MAX3232IPW Texas Instruments بەکارهێنراوە لە: USB-to-UART Debug Adapter STM32F103ZGT6JTR Microcontroller target using the UART debug path بەکارهێنراوە لە: USB-to-UART Debug Adapter CY7C68013A-56LTXI Infineon بەکارهێنراوە لە: USB-to-UART Debug Adapter MX25L6433F-2SL SPI flash storage companion بەکارهێنراوە لە: SPI Peripheral Bridge STM32F765VGT6TR STMicroelectronics بەکارهێنراوە لە: SPI Peripheral Bridge LAN9353T/PT Microchip Technology بەکارهێنراوە لە: SPI Peripheral Bridge PCF8574DWR Texas Instruments بەکارهێنراوە لە: Capacitive Touch USB Peripheral PCA9554PWR NXP Semiconductors بەکارهێنراوە لە: Capacitive Touch USB Peripheral STM32F103R8T6TR STMicroelectronics بەکارهێنراوە لە: Capacitive Touch USB Peripheral MCP3428-E/ST Microchip Technology بەکارهێنراوە لە: USB Battery-Charging Detection Adapter MCP608-I/SN Microchip Technology بەکارهێنراوە لە: USB Battery-Charging Detection Adapter USB2227-NU-05 Microchip Technology بەکارهێنراوە لە: USB Battery-Charging Detection Adapter ISO1430BDWR Texas Instruments بەکارهێنراوە لە: Industrial USB Serial Gateway LAN8742-CZ-TR Microchip Technology بەکارهێنراوە لە: Industrial USB Serial Gateway SP490ECN-L/TR MaxLinear بەکارهێنراوە لە: Industrial USB Serial Gateway
What is the CY7C65215A-32LTXI?
The CY7C65215A-32LTXI is an Infineon Technologies USB-serial dual-channel bridge controller that provides UART, I2C, and SPI connectivity through a USB 2.0 full-speed interface. According to the manufacturer datasheet, it supports data rates up to 12 Mbps and integrates CAPSENSE, Battery Charging Detection, a voltage regulator, an oscillator, and flash memory for configuration storage in a 32-QFN package.
What interfaces does the CY7C65215A-32LTXI support?
The CY7C65215A-32LTXI supports UART, I2C, and SPI through its dual-channel serial interface. According to the manufacturer datasheet, this allows one USB connection to serve serial peripherals using more than one protocol. Designers should select the operating protocol and channel configuration in the controller configuration data before the USB host begins normal peripheral communication.
What is the maximum USB data rate of the CY7C65215A-32LTXI?
The CY7C65215A-32LTXI supports USB full-speed operation up to 12 Mbps. The manufacturer product page identifies the device as a USB 2.0 peripheral controller, while the manufacturer datasheet describes the CY7C65215/CY7C65215A as a full-speed USB controller. Actual application throughput can be lower when protocol overhead, host behavior, or the connected peripheral limits the transfer rate.
Where can I download the CY7C65215A-32LTXI datasheet PDF?
The official CY7C65215A-32LTXI datasheet PDF is available from the Infineon Technologies document link on this page. The document covers the USB-serial dual-channel architecture, UART, I2C, and SPI operation, CAPSENSE, Battery Charging Detection, power modes, package information, and electrical characteristics. Use the manufacturer PDF for the authoritative pin descriptions and application guidance.
Where can I find the CY7C65215A-32LTXI pinout?
The CY7C65215A-32LTXI uses a 32-pin QFN package, and the pin assignment is identified in the manufacturer datasheet. Use the package drawing and pin-description table in that document when assigning USB, serial-interface, power, ground, configuration, and programming signals. The exposed-pad and thermal-layout requirements should also be implemented exactly as shown in the package information and recommended land pattern.
Can the CY7C65215A-32LTXI use both bus-powered and self-powered operation?
Yes, the CY7C65215A-32LTXI supports bus-powered and self-powered USB operation. The manufacturer datasheet identifies both operating approaches and describes suspend and remote wake-up functions for system power management. A self-powered design still needs to handle USB enumeration and bus-supplied signaling correctly, while a bus-powered design must remain within the power budget supported by the USB connection.
Does the CY7C65215A-32LTXI support CAPSENSE and battery charging detection?
The CY7C65215A-32LTXI integrates both CAPSENSE and Battery Charging Detection. According to the manufacturer datasheet, the battery-charging function complies with USB Battery Charging Specification Revision 1.2. CAPSENSE can add capacitive touch or proximity control to a USB peripheral without requiring a separate touch-controller package, subject to the layout and calibration guidance in the datasheet.
What is the difference between CY7C65215A-32LTXI and CY7C65215-32LTXI?
Both devices are identified as full-speed USB-serial dual-channel bridge controllers with UART, I2C, and SPI support and are associated with the 32-QFN package family. The listed maximum USB data rate for the A version is 12 Mbps, while a separate maximum-rate value for the non-A version is not stated in the available product information. Firmware, ordering, and electrical details should therefore be checked before interchanging them.
When should I choose the CY7C65215A-32LTXI over a different USB bridge?
Choose the CY7C65215A-32LTXI when a compact 32-QFN USB interface must provide configurable UART, I2C, or SPI connectivity together with CAPSENSE and battery-charging detection. The integrated regulator, oscillator, and configuration flash simplify the implementation. If a design instead requires a different package, a fixed protocol, another USB speed, or another data-rate class, select that bridge only after confirming the host software and peripheral electrical requirements.
Is the CY7C65215A-32LTXI suitable for an industrial USB-to-I2C gateway?
The CY7C65215A-32LTXI is suitable for a USB-to-I2C gateway when the gateway can use its supported I2C channel and does not exceed the device's specified electrical or timing limits. Its 12 Mbps USB full-speed interface permits efficient enumeration and command transfer, while the internal flash stores configuration parameters. Industrial use should also include suitable protection, grounding, and environmental qualification for the deployed enclosure.
What can replace the CY7C65215A-32LTXI?
The closest verified same-package option is the Infineon Technologies CY7C65215-32LTXI, which shares the 32-QFN footprint and the listed full-speed USB dual-channel bridge function. Its separately listed maximum-rate value is not stated, so it should be treated as a conditional replacement rather than an automatic substitute. Confirm pin behavior, configuration compatibility, temperature grade, and all electrical limits against the manufacturer datasheet before redesigning.
Can a USB-UART bridge replace the CY7C65215A-32LTXI?
A dedicated USB-to-UART bridge cannot automatically replace the CY7C65215A-32LTXI because the target also supports I2C, SPI, CAPSENSE, Battery Charging Detection, and configurable dual-channel operation. Replacing it with a UART-only device would normally require a different footprint, additional serial interfaces, and host-driver changes. Use the manufacturer's comparison resources to validate any proposed migration rather than treating functional similarity as drop-in compatibility.
What is the best Infineon Technologies equivalent for the CY7C65215A-32LTXI?
The best verified Infineon Technologies alternative is the CY7C65215-32LTXI because it belongs to the same bridge family and shares the 32-QFN 5x5 mm package class. It is the only candidate in the retrieved cross-reference results that can be presented as a same-package option without changing the land pattern. Its electrical, configuration, and maximum-rate details must still be checked against the target datasheet before production use.
Where can I buy the CY7C65215A-32LTXI online?
The CY7C65215A-32LTXI can be requested through the Request a Quote form on this page. The form allows buyers to specify quantity, target delivery location, and required packaging while obtaining current commercial terms for the exact 32-QFN ordering code. Current stock and lead time should be confirmed at the time of the request because availability for specialized interface controllers can change.
What is the price of the CY7C65215A-32LTXI?
Current pricing for the CY7C65215A-32LTXI is handled through the Request a Quote form on this page. Submit the exact MPN, quantity, and required shipment details to receive a current quotation without relying on an outdated list price. The form is also the appropriate route for volume pricing and production scheduling rather than assuming a generic marketplace price.
Is the CY7C65215A-32LTXI in stock, and what is its lead time?
Use the Request a Quote form on this page to check current stock, minimum order quantity, and lead time for the CY7C65215A-32LTXI. Availability is assessed for the exact ordering code, including its 32-QFN package and temperature suffix. Because inventory and production schedules can change, a written quotation provides a more reliable basis for purchasing than an undated stock indicator.

داتای سەرچاوەی ئەندازیاری بۆ CY7C65215A-32LTXI — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the CY7C65215A-32LTXI when the design needs a compact USB full-speed bridge with configurable UART, I2C, or SPI connectivity, persistent configuration, CAPSENSE, and battery-charging detection. Its integrated regulator, oscillator, and flash can simplify board design, while the 32-QFN 5x5 mm package supports space-constrained products. The CY7C65215-32LTXI is the closest verified same-package option and may suit an existing design using that revision, but its separate maximum-rate value is not stated and must be confirmed. Dedicated UART bridges are generally smaller but do not reproduce the target's I2C, SPI, CAPSENSE, and BCD integration, so they require additional circuitry and different host support. Before choosing any substitute, verify the land pattern, pin behavior, electrical limits, temperature grade, firmware descriptors, and host-driver compatibility.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە CY7C65215-32LTXI
Package 32-QFN (5x5 mm) 32-QFN (5x5 mm)
Brand Infineon Technologies Infineon Technologies
Device Type USB-serial dual-channel bridge controller USB-serial dual-channel bridge controller
USB Standard USB 2.0 full-speed USB full-speed
Serial Interfaces UART, I2C, and SPI UART, I2C, and SPI
Integrated CAPSENSE Yes Yes
Battery Charging Detection BCD, compliant with USB Battery Charging Specification Revision 1.2 BCD, compliant with USB Battery Charging Specification Revision 1.2
Power Modes Bus-powered and self-powered Bus-powered and self-powered
Integrated Configuration Storage Flash memory Flash memory

جیاکەرەوە سەرەکییەکان

  • Combines three serial protocols with USB in one controller (بەراورد بەCY7C65215-32LTXI)
  • Integrates CAPSENSE with a USB serial bridge (بەراورد بەCY7C65215-32LTXI)
  • Adds battery-charging detection to the same compact package (بەراورد بەCY7C65215-32LTXI)

تێبینییەکانی دیزاین

Route USB D+ and D- as a controlled-impedance differential pair over a continuous reference plane, following the manufacturer layout and impedance guidance. Keep the pair length matched, minimize vias and stubs, and place connector protection close to the external interface. Locate the required USB-bus capacitors at the controller pins and avoid placing unrelated high-current or switching nodes beneath the USB pair.

Separate the internal regulator's local bypass network from the USB power path and follow the datasheet's recommended capacitance and placement. Verify both bus-powered and self-powered behavior, including suspend current and remote-wake-up operation. For a self-powered product, prevent back-powering the USB host during suspend by using the correct power-management topology and isolation strategy.

Do not assume that any UART, I2C, or SPI-capable bridge is interchangeable with this controller. Confirm the package land pattern, active levels, serial timing, configuration format, USB descriptors, and host-driver expectations. The CY7C65215-32LTXI is a same-family candidate, but revision-specific electrical limits and maximum-rate details must be compared before production substitution.

Use the manufacturer CAPSENSE guidance for sensor traces, guard structures, grounding, and shielding. Keep sensor copper away from switching nodes and maintain consistent clearance between the sensor electrode and surrounding copper. Changes to the enclosure, cable, ground geometry, or adjacent circuitry can alter touch performance, so validate the final mechanical assembly rather than relying only on bare-board measurements.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS compliance is listed for the exact MPN. The -LTXI ordering suffix identifies the lead-free package configuration. Other compliance fields are not established by the product information.

داتا پشتڕاستکراوەتەوە لە: 2026-11-04 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

CY7C65215A-32LTXI datasheet CY7C65215A datasheet pdf CY7C65215A-32LTXI pinout CY7C65215A-32LTXI specifications Infineon CY7C65215A-32LTXI CY7C65215A-32LTXI 32-QFN CY7C65215A-32LTXI USB 12 Mbps CY7C65215A-32LTXI equivalent CY7C65215A-32LTXI replacement CY7C65215A-32LTXI price CY7C65215A-32LTXI stock CY7C65215A USB UART I2C SPI bridge CY7C65215A-32LTXI CAPSENSE CY7C65215A-32LTXI cross reference CY7C65215A-32LTXI footprint

پێکهاتە و زاراوە پەیوەندیدارەکان

Infineon Technologies CY7C65215A-32LTXI CY7C65215-32LTXI USB-serial bridge controller USB interface IC USB 2.0 full-speed UART I2C SPI CAPSENSE Battery Charging Detection USB Battery Charging Specification Revision 1.2 32-QFN package QFN family surface mount technology semiconductor embedded flash memory voltage regulator internal oscillator bus-powered mode self-powered mode remote wake-up suspend mode 12 Mbps
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ