DP83848EVV/NOPB - 10/100 Ethernet PHY | Texas Instruments
MPN: DP83848EVV/NOPB ✓ چالاکDP83848EVV/NOPB گشتی
An Ethernet PHY is the analog and digital interface layer between a network controller and physical copper cable. It translates MAC-facing data through an MII or RMII interface, applies line encoding and signaling, and recovers data from the received physical signal. In this product hierarchy, the Ethernet PHY sits above the Ethernet transceiver function and below the Ethernet interface IC category, providing the physical link required by industrial Ethernet equipment.
The DP83848EVV/NOPB is identified in the product records as an Ethernet transceiver with a 48-LQFP package. The related DP83848IVV/NOPB listing identifies the package as 7 x 7 mm and specifies a temperature range of -40°C to +85°C. The related DP83848IVVX/NOPB listing is explicitly presented as another member of the same DP83848I family, allowing package and feature-level comparison during replacement qualification. Detailed electrical ratings for the exact EVV suffix must be confirmed in the applicable National Semiconductor or Texas Instruments documentation before production release.
The device family is positioned for industrial Ethernet systems where a dedicated PHY connects an embedded processor, programmable logic, or industrial controller to a 10BASE-T or 100BASE-TX network. Its integrated PHY reduces the number of external line-interface components required on a controller board, while standardized MAC-facing interfaces let the PHY operate with compatible Ethernet controllers. The exact supported media, interface modes, clocking requirements, and strap options should be selected from the pin-description and operating-information tables in the manufacturer datasheet.
Typical design contexts include industrial Ethernet switches, embedded control systems, factory automation equipment, serial-to-Ethernet gateways, instrumentation, and network-enabled test equipment. In these applications, the DP83848EVV/NOPB handles the physical layer while the host processor manages packet processing and network services. Board-level implementation still requires a suitable Ethernet magnetics section, compliant cable-side routing, a stable clock source, and careful separation of sensitive analog and digital signals.
For layout, place the PHY and its supporting passive network close to the Ethernet connector or cable entry point to minimize differential-pair impedance discontinuity and insertion loss. Keep the 10/100-Mbps magnetic-device side of the interface physically compact, provide the power and decoupling networks recommended by the family documentation, and route differential pairs as a controlled-impedance pair. Do not substitute the EVV suffix with IVV or IVVX without reviewing the exact pin, temperature, interface, and ordering-code differences.
This product page combines the available manufacturer and distributor information with practical Ethernet-PHY placement guidance, package-aware alternatives, and an explicit verification checklist. It is intended to accelerate sourcing and board review while preserving the distinction between documented facts and parameters that still require confirmation from the exact suffix datasheet and current TI product page.
جێگرەوەکانی جێگۆڕکێ بۆ DP83848EVV/NOPB — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DP83848EVV/NOPB (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Standards, Supply Voltage, Operating Temperature.
DP83848IVV/NOPB
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83848IVVX/NOPB
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83848EVV/NOPB تایبەتمەندییەکان
| Device Type | Ethernet transceiver / 10-100-Mbps PHY |
| Supported Data Rate | 10/100 Mbps |
| Number of Ports | 1 port |
| پاکێج | 48-LQFP (7 x 7 mm) |
| Total Pin Count | 48 pins |
| جۆری دامەزراندن | Surface mount |
| Industrial Temperature Range of Related DP83848IVV/NOPB | -40°C to +85°C |
| SNI Support on Related DP83848IVV/NOPB | Supported |
| JTAG Support on Related DP83848IVV/NOPB | Supported |
ڕێنمایی ڕێکخستنی پینی DP83848EVV/NOPB 48-lqfp (7 x 7 mm)
ڕێکخستنی پین بۆ DP83848EVV/NOPB (پاکێجی 48-lqfp (7 x 7 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DP83848EVV/NOPB.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DP83848EVV/NOPB گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Control Systems, Industrial Ethernet Switches, Factory Automation Gateways, Networked Instrumentation, Programmable Logic Ethernet Interfaces, Serial-to-Ethernet Equipment.
Industrial Ethernet Control Systems
The DP83848EVV/NOPB fits industrial controllers that require a dedicated 10/100-Mbps Ethernet physical layer between a processor and a copper network. It is appropriate for PLCs, factory controllers, and distributed automation equipment where the Ethernet interface must coexist with control logic on a dense mixed-signal board. The related DP83848IVV/NOPB is documented for -40°C to +85°C, SNI, and JTAG, making it a useful family reference when industrial diagnostic features are required. Place the PHY near the magnetic-device network interface, use the family-recommended decoupling, and verify the exact EVV temperature and interface options before production.
پێشنیارکراو
Industrial Ethernet Switches
DP83848EVV/NOPB can serve as the physical-layer device on a single-port industrial switch or network interface card. Its 48-LQFP construction gives a compact, surface-mount solution for equipment requiring one 10/100-Mbps copper port alongside a switching ASIC or embedded controller. The PCB should separate the PHY from the switching fabric while keeping the differential network traces short and controlled. Review the exact EVV media-support configuration, MAC interface, clock source, and reset behavior in the manufacturer documentation. Use the evaluation-board schematic as a starting point for magnetics, termination, and layout integration.
پێشنیارکراو
Factory Automation Gateways
A DP83848EVV/NOPB-based gateway can connect an embedded controller to a 10/100-Mbps industrial Ethernet segment for telemetry, configuration, and supervisory control. The PHY handles the cable-facing signaling while the host processor manages protocols and local automation tasks. For deployments with wide ambient-temperature requirements or diagnostic access, the documented DP83848IVV/NOPB family member provides an industrial -40°C to +85°C option with SNI and JTAG support. Confirm the EVV suffix limits, isolation strategy, surge protection, and grounding arrangement. Do not allow copper-network surge paths to bypass the intended protection and isolation components.
پێشنیارکراو
Networked Instrumentation
The DP83848EVV/NOPB is suitable for laboratory and process instrumentation that adds Ethernet connectivity to a measurement or control board. A 10/100-Mbps PHY allows legacy serial or parallel control logic to communicate with remote operators and supervisory software while using an economical copper network connection. The implementation should reserve solid grounding near the PHY, maintain symmetry between the transmit and receive differential pairs, and isolate the network connector region from high-impedance analog inputs. Review the exact EVV operating-temperature grade and interface options before deploying it in calibrated test equipment.
پێشنیارکراو
Programmable Logic Ethernet Interfaces
DP83848EVV/NOPB can provide the physical layer for FPGA-based communication, data-acquisition, and protocol-conversion boards. The PHY can offload Ethernet line signaling from the programmable logic while a soft MAC or hardware controller manages packet traffic. The principal design constraints are a clean reference clock, correct strap settings, deterministic reset sequencing, and a compact network-side layout. Use the manufacturer family documentation to map the MAC-facing pins and consult the evaluation-board schematic for recommended magnetic-device and termination arrangements. Validate the exact EVV feature set before assigning SNI, JTAG, or other configuration functions in the FPGA logic.
پێشنیارکراو
Serial-to-Ethernet Equipment
A serial-to-Ethernet product can pair DP83848EVV/NOPB with a host MCU or embedded Linux processor to expose legacy serial, industrial protocol, or configuration data over a 10/100-Mbps network. The PHY allows the host to focus on packet processing while handling the physical Ethernet layer in dedicated silicon. In a compact appliance, thermal and EMI conditions may constrain the magnetics, connector, and PHY placement, making the 7 x 7 mm 48-LQFP format useful for compact layouts. Confirm EVV-specific electrical and thermal limits, provide the required filtering, and verify link behavior across long cables and industrial-noise conditions before release.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DP83848EVV/NOPB — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DP83848IVV/NOPB | DP83848IVVX/NOPB |
|---|---|---|---|
| Package | 48-LQFP, 7 x 7 mm | 48-LQFP (PT), 7 x 7 mm | 48-LQFP, 7 x 7 mm |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Class | Ethernet transceiver / 10-100-Mbps PHY | 10/100-Mbps Ethernet PHY transceiver | DP83848I Ethernet PHY family member |
جیاکەرەوە سەرەکییەکان
- Same 48-LQFP family package (بەراورد بەDP83848IVV/NOPB)
- Documented industrial feature set on the IVV alternative (بەراورد بەDP83848IVV/NOPB)
- Single-port 10/100-Mbps positioning (بەراورد بەDP83848IVV/NOPB)
تێبینییەکانی دیزاین
Place DP83848EVV/NOPB close to the Ethernet magnetic device and connector-side components. Keep the transmit and receive differential pairs short, symmetrical, and routed over a continuous reference plane. Avoid stubs, test pads, and high-current traces crossing the pairs. Confirm the EVV-specific reference network and magnetics recommendations in the manufacturer family documentation before releasing the layout.
Use the manufacturer-recommended power, ground, and decoupling arrangement around the PHY. Keep switching regulators and their high-current loops away from the PHY's clock, reference, and analog-supply areas. Provide a low-impedance ground path beneath the device and use the evaluation-board schematic to check the connection sequence among the PHY, magnetic device, and connector.
Do not treat the shared 48-LQFP outline as proof that every DP83848I ordering suffix is interchangeable. Compare the exact EVV and replacement ordering tables for pin functions, temperature grade, SNI, JTAG, clock requirements, and media support. Validate strap settings and reset sequencing on hardware, because copied configurations from a related suffix can produce different link or test-mode behavior.
Treat the Ethernet magnetics and connector as part of the EMI-controlled region, not merely as optional interface components. Use the documented filtering and termination values, maintain short return paths, and provide chassis or signal-ground connections according to the isolation strategy. Verify conducted and radiated emissions with the production enclosure, cable, and grounding arrangement because changes outside the PCB can alter compliance performance.
زانیاری پابەندبوون
Compliance attributes for the exact DP83848EVV/NOPB suffix were not established by the available product records. Verify RoHS, REACH, AEC-Q100 status, lead-free status, halogen-free status, and conflict-minerals declarations using the exact manufacturer documentation or current product-page declarations.