DP83867IRPAPR - Industrial Gigabit Ethernet PHY | Texas Instruments
MPN: DP83867IRPAPR ✓ چالاکDP83867IRPAPR گشتی
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts between a digital MAC-side interface and analog signals carried over twisted-pair cabling. The DP83867IR belongs to the physical-layer layer of the Ethernet hierarchy, supporting 10BASE-T, 100BASE-TX, and 1000BASE-T operation. Its RGMII and SGMII interfaces allow connection to a network controller or other suitable Ethernet digital interface.
The DP83867IR is positioned for industrial systems that require a single-port Gigabit Ethernet physical layer with high-immunity operation. The verified product information identifies cable diagnostics, IEEE 1588 support, and JTAG 1149.1 among the device features. Its -40 °C to 85 °C industrial-temperature range supports deployment in factory automation, industrial controls, communications equipment, and embedded systems operating across extended temperature environments.
The 64-pin HTQFP (PAP) construction provides a conventional surface-mount footprint for industrial Ethernet designs. The RGMII interface supports conventional parallel Ethernet connectivity, while SGMII offers a serial alternative for designs using a compatible controller or PHY arrangement. Interface selection should be made during schematic definition because signal timing, clocking, voltage domains, and controller support determine which implementation is appropriate.
Typical uses include industrial Ethernet switches, programmable automation controllers, factory-floor gateways, motor-control platforms, building-control equipment, and embedded communications modules. The -40 °C to 85 °C range is particularly relevant to equipment installed near machinery, outdoor enclosures, or other locations with wide ambient-temperature variation.
Design planning must include the complete DP83867IR datasheet pin list, power requirements, clocking scheme, magnetic-interface configuration, and initialization sequence. Validate the selected board layout, magnetics, cable reach, EMC behavior, and link negotiation in the final industrial enclosure rather than relying only on generic Ethernet design assumptions.
This product page consolidates the verified device classification, package information, temperature range, interface details, sourcing data, and practical engineering considerations into one design reference. It also distinguishes a true same-footprint substitute from related parts and evaluation modules that cannot automatically replace the DP83867IRPAPR.
جێگرەوەکانی جێگۆڕکێ بۆ DP83867IRPAPR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DP83867IRPAPR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Cable Diagnostics, Operating Temperature Range, Package, Pin Count.
هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.
داوای جێگرەوەکان بکەDP83867IRPAPR تایبەتمەندییەکان
| Product Type | 10/100/1000 Base-T Ethernet physical-layer transceiver |
| Supported Ethernet Speeds | 10/100/1000 Mb/s |
| Maximum Ethernet Speed | 1000 Mb/s |
| Digital Interface | RGMII and SGMII |
| Number of Ports | 1 port |
| مەودای پلەی گەرمیی کارکردن | -40 °C to 85 °C |
| Temperature Grade | Industrial temperature |
| پاکێج | 64-pin HTQFP (PAP) |
| Package Body Size | 10 mm x 10 mm |
| ژمارەی پین | 64 pins |
| جۆری دامەزراندن | Surface mount |
| Cable Diagnostics | Supported |
| IEEE 1588 Support | Supported |
| Debug Interface | JTAG 1149.1 |
| Robustness Classification | Robust, high-immunity Ethernet PHY |
ڕێنمایی ڕێکخستنی پینی DP83867IRPAPR 10 mm x 10 mm
ڕێکخستنی پین بۆ DP83867IRPAPR (پاکێجی 10 mm x 10 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DP83867IRPAPR.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DP83867IRPAPR گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Switches, Factory Automation Controllers, Industrial IoT Gateways, Building-Control Equipment, Embedded Communications Modules, Robust Network Test Equipment.
Industrial Ethernet Switches
The DP83867IRPAPR fits single-port copper Ethernet ports in industrial switching equipment because it supports 10/100/1000 Mb/s operation, RGMII and SGMII connectivity, and the -40 °C to 85 °C industrial-temperature range. A switch design can use RGMII when the switching silicon provides a compatible parallel interface, or select SGMII where the controller supports serial Ethernet connectivity. The robust, high-immunity PHY classification is useful in factory-floor equipment where conducted and radiated interference may be elevated. Before layout release, verify magnetics, termination, clock source, reference clocking, reset behavior, and the manufacturer's recommended layout against the final enclosure and cable environment.
پێشنیارکراو
Factory Automation Controllers
The DP83867IRPAPR provides a standards-based Gigabit Ethernet endpoint for programmable automation controllers, data acquisition modules, and factory gateways. Its single 10/100/1000 Mb/s copper port supports legacy 10 Mb/s and 100 Mb/s links as well as Gigabit operation, while the -40 °C to 85 °C range covers equipment expected to operate near heat-producing machinery. RGMII or SGMII connectivity provides design flexibility with compatible control silicon. The final controller interface must be checked for clock mode, data timing, voltage levels, and supported PHY initialization, while the complete assembly should undergo EMC and network-link testing in its intended enclosure.
پێشنیارکراو
Industrial IoT Gateways
The DP83867IRPAPR is appropriate for industrial IoT gateways that bridge local sensors, programmable controllers, and an upstream Ethernet network. Its 10/100/1000 Mb/s capability supports common plant-network link speeds, while the industrial-temperature range supports gateways installed in uncontrolled cabinets or outdoor-rated enclosures. The 64-pin HTQFP (PAP) package provides a defined surface-mount integration point for high-speed RGMII routing or SGMII connectivity. Cable diagnostics and JTAG 1149.1 can assist commissioning and troubleshooting, but production firmware must use the DP83867IR initialization sequence and should preserve the manufacturer-prescribed strap and register settings.
پێشنیارکراو
Building-Control Equipment
The DP83867IRPAPR can support Ethernet connectivity in building controllers, room controllers, HVAC interfaces, access-control terminals, and energy-management equipment. Its -40 °C to 85 °C operating range suits indoor equipment located near heat sources, while support for 1000BASE-T alongside 10BASE-T and 100BASE-TX allows interoperability with different network infrastructure. RGMII or SGMII connects the PHY to suitable embedded controller silicon. Designers should account for isolated or non-isolated magnetics, Ethernet transformer layout, surge protection, grounding, and enclosure-specific electromagnetic compatibility rather than treating the PHY as a complete Ethernet protection solution.
پێشنیارکراو
Embedded Communications Modules
The DP83867IRPAPR supports embedded communications modules that need a robust copper Ethernet front end while the host processor handles higher-level networking. The PHY provides RGMII or SGMII interfaces instead of requiring the host to implement the complete physical layer, and its 10/100/1000 Mb/s capability accommodates legacy and high-speed links. The -40 °C to 85 °C range supports industrial embedded modules, but the module designer remains responsible for the magnetics, reference clock, decoupling, impedance-controlled traces, firmware driver, and regulatory testing. IEEE 1588 and cable-diagnostic support can improve timestamped or service-oriented industrial network functionality when the host software enables them.
پێشنیارکراو
Robust Network Test Equipment
The DP83867IRPAPR can be used in portable or industrial network test equipment where a copper Ethernet endpoint must operate across a wide temperature range. Support for 10/100/1000 Mb/s links, cable diagnostics, and JTAG 1149.1 assists interoperability testing and hardware debugging. The RGMII or SGMII interface connects the PHY to a test processor or communications controller, while the 64-pin HTQFP package supports compact, repeatable board layouts. Because a diagnostic PHY does not remove the need for physical-layer validation, production testing should include link negotiation at all supported speeds, cable-length checks, clock-quality measurements, temperature operation, and verification of custom cable or magnetics configurations.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DP83867IRPAPR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Brand | Texas Instruments |
| Package | 64-pin HTQFP (PAP), 10 mm x 10 mm |
| Product Type | 10/100/1000 Base-T Ethernet PHY transceiver |
| Ethernet Speed | 10/100/1000 Mb/s |
| Digital Interface | RGMII and SGMII |
| Port Count | 1 port |
| Operating Temperature | -40 °C to 85 °C |
| Temperature Grade | Industrial |
| Cable Diagnostics | Supported |
| IEEE 1588 Support | Supported |
| Debug Interface | JTAG 1149.1 |
| Package Pin Count | 64 pins |
جیاکەرەوە سەرەکییەکان
- Industrial-temperature operation (بەراورد بەDP83869HM)
- Broad Ethernet link-speed support (بەراورد بەDP83848VYB/NOPB)
- Flexible controller connectivity (بەراورد بەDP83867ISRGZR)
- Integrated diagnostic and debug functions (بەراورد بەDP83867IRPAPT)
تێبینییەکانی دیزاین
Use the DP83867IR family datasheet as the controlling reference for the 64-pin HTQFP layout. Place Ethernet magnetics and the high-speed digital interface in accordance with the manufacturer's reference design, keep the digital and analog supply paths appropriately separated, and minimize loop area around supply connections. The RGMII or SGMII route must be treated as a high-speed constrained interface, with return paths, impedance, connector or magnetics placement, and ESD structures considered together rather than as separate routing tasks.
Do not treat a related DP83867 orderable entry as an automatic electrical substitute. The DP83869HM has documented differences in power sequencing, strap-resistor interpretation, default register states, Auto-MDIX initialization, LED modes, and IEEE 1588 timestamping, and it is explicitly not a drop-in replacement. Confirm the exact suffix, package, temperature grade, initialization sequence, strap settings, and firmware support before approving a replacement for design, qualification, or obsolescence mitigation.
Validate the complete initialization path, including strap sampling, reset release, PHY register configuration, link negotiation, and any LED or timestamping functions. The DP83867IR supports cable diagnostics, IEEE 1588, and JTAG 1149.1, but enabling a feature does not guarantee that the host software, cable, magnetics, and system timing implement it correctly. Use the manufacturer-recommended startup sequence and test link establishment at 10, 100, and 1000 Mb/s across the intended cable and temperature conditions.
The device's robust, high-immunity positioning does not remove the need for an EMC-qualified Ethernet subsystem. Use suitable magnetics, controlled board geometry, properly terminated differential pairs, appropriate chassis grounding, and the protection strategy required by the installation environment. Industrial products may face conducted noise, electrostatic discharge, and surge threats that cannot be solved by the PHY alone. Validate the assembled enclosure and representative cables because shielding, enclosure openings, cable type, and grounding often determine final EMC performance.
زانیاری پابەندبوون
The verified ordering information identifies the industrial-temperature grade and package but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these declarations with Texas Instruments for the exact orderable entry before regulatory submission.