DP83867ISRGZT Industrial Gigabit Ethernet PHY | Texas Instruments
MPN: DP83867ISRGZT ✓ چالاکDP83867ISRGZT گشتی
An Ethernet physical-layer transceiver, or Ethernet PHY, is the semiconductor layer that converts digital Ethernet data into signals suitable for transmission over twisted-pair cable. It sits between a network controller or system-on-chip and the external RJ45 magnetic interface. Within the network architecture, the DP83867IS belongs to the PHY, physical-layer transceiver, Ethernet interface IC, and semiconductor hierarchies.
The DP83867IS is positioned for industrial systems that require robust Gigabit Ethernet connectivity. Its operating-temperature range of -40°C to +85°C exceeds the range of typical commercial-temperature PHYs. A single-port architecture simplifies board routing, while RGMII support allows direct connection to many Ethernet controllers and SGMII support supports serial links to higher-speed fabric or switching silicon.
The device integrates the physical-medium dependent sublayers required for 10BASE-T, 100BASE-TX, and 1000BASE-T operation. Supporting all three rates in one PHY permits a single copper-network design to accommodate legacy 10 Mbit/s and 100 Mbit/s endpoints as well as full-duplex Gigabit links. The availability of 1.0 V, 1.8 V, and 2.5 V interface rails supports integration with processors, FPGAs, switching fabrics, and industrial controllers operating at different logic levels.
Typical applications include industrial Ethernet controllers, factory automation equipment, networked sensors, motor-drive systems, building-automation gateways, and embedded routers. The combination of RGMII and SGMII makes the device suitable for designs that must accommodate parallel MAC connections, serial fabric links, or platform variants using different network architectures.
PCB implementation requires careful treatment of the exposed pad, analog supply rails, clock sources, and high-speed digital interfaces. Place the PHY close to the network connector and magnetics, route differential pairs as impedance-controlled pairs, and use a solid ground-plane arrangement beneath the device. Follow the manufacturer datasheet for the exposed-pad connection, decoupling capacitors, isolation boundaries, and analog-layout requirements.
This page organizes the DP83867ISRGZT’s industrial Ethernet role, interface options, temperature range, package constraints, application guidance, drop-in candidates, and engineering considerations into a practical selection reference for designers building robust copper-based Ethernet equipment.
جێگرەوەکانی جێگۆڕکێ بۆ DP83867ISRGZT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DP83867ISRGZT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Cable Diagnostics, Operating Temperature Range, MAC Interface.
DP83867IRRGZR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867CSRGZT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867ERGZR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867ISRGZR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →DP83867ISV
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DP83867ISRGZT تایبەتمەندییەکان
| Product Type | Single-port 10/100/1000 Ethernet physical-layer transceiver |
| Ethernet Data Rates | 10 Mbit/s, 100 Mbit/s, and 1 Gbit/s |
| Supported Copper Protocols | 10BASE-T, 100BASE-TX, and 1000BASE-T |
| Host Interface Options | RGMII and SGMII |
| Number of Ports | 1 port |
| مەودای پلەی گەرمیی کارکردن | -40°C to +85°C |
| Temperature Grade | Industrial temperature |
| Interface Voltage Rails | 1.0 V, 1.8 V, and 2.5 V |
| پاکێج | RGZ VQFN, 48 pins |
| Package Body Size | 7 mm × 7 mm |
| جۆری دامەزراندن | Surface mount |
| Integrated PMD Sublayers | Supported for 10BASE-T, 100BASE-TX, and 1000BASE-T |
| Maximum Link Rate | 1 Gbit/s |
ڕێنمایی ڕێکخستنی پینی DP83867ISRGZT 7 mm × 7 mm
ڕێکخستنی پین بۆ DP83867ISRGZT (پاکێجی 7 mm × 7 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DP83867ISRGZT.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DP83867ISRGZT گونجاوە بۆ 6 بەکارھێنانs: Industrial Factory Automation Controllers, Industrial Motor Drive Networking, Building Automation Gateways, Embedded Routers and Edge Gateways, Networked Sensors and IoT Gateways, Test and Measurement Network Ports.
Industrial Factory Automation Controllers
The DP83867ISRGZT fits industrial automation controllers that connect sensors, drives, remote I/O, and supervisory systems over copper Ethernet. Its 10/100/1000 Mbit/s support accommodates legacy equipment and Gigabit backbones, while the -40°C to +85°C operating range suits factory-floor temperature conditions. RGMII provides a direct parallel interface to suitable controllers, and SGMII supports serial links to switching or fabric silicon. The 48-pin RGZ VQFN keeps the design compact, although industrial layouts still require controlled Ethernet magnetics, impedance-matched pairs, robust grounding, and isolation appropriate to the installation.
پێشنیارکراو
Industrial Motor Drive Networking
The DP83867ISRGZT is appropriate for networked motor-drive controllers that need deterministic copper-Ethernet connectivity for configuration, diagnostics, and supervisory control. It supports 100BASE-TX and 1000BASE-T operation, allowing designers to combine slower legacy service networks with faster plant backbones. The industrial-temperature range of -40°C to +85°C supports equipment deployed outside controlled office environments. Its RGMII and SGMII options allow the PCB to target either a parallel MAC interface or a serial network backbone, but the design must account for motor-converter electrical noise, shield grounding, magnetic-component selection, and careful separation between switching power stages and PHY circuitry.
پێشنیارکراو
Building Automation Gateways
The DP83867ISRGZT can serve as the Ethernet interface in building-automation gateways that bridge HVAC, lighting, access-control, and energy-management equipment. Its single-port 10/100/1000 capability supports retrofit devices operating at 10 or 100 Mbit/s as well as modern high-bandwidth building controllers. The -40°C to +85°C range is useful in unheated equipment rooms, and RGMII or SGMII gives the host designer architectural flexibility. For reliable building deployment, pair the PHY with an industrial-rated network transformer, provide protected cable interfaces, isolate communications grounds where required, and route the Ethernet differential pair away from switching regulators and high-current relays.
پێشنیارکراو
Embedded Routers and Edge Gateways
The DP83867ISRGZT fits embedded routers and edge gateways that need a robust copper-Ethernet port for management, service access, or uplink connectivity. Supporting 10, 100, and 1,000 Mbit/s makes the PHY suitable for both legacy management ports and modern aggregation links. Its industrial-temperature grade broadens deployment from indoor telecom equipment to outdoor cabinets and distributed monitoring stations. RGMII can connect directly to a suitable network controller, while SGMII can simplify links to switching silicon. In compact systems, thermal management of the processor and PHY, exposed-pad soldering, magnetics placement, and Ethernet-pair routing can determine whether the additional speed and operating range translate into reliable field performance.
پێشنیارکراو
Networked Sensors and IoT Gateways
The DP83867ISRGZT is useful in connected sensors and IoT aggregation gateways that bridge low-speed industrial endpoints to faster Ethernet infrastructure. The PHY supports 100BASE-TX for distributed sensors and 1000BASE-T for local data collection or uplink capacity. Its -40°C to +85°C range supports equipment installed in varied ambient conditions, while the 48-pin RGZ VQFN limits board area in compact enclosures. Designers should use low-noise analog supplies, maintain the manufacturer’s decoupling and exposed-pad layout, and keep Ethernet magnetics close to the connector. Firmware-driven PHY configuration should also be validated because cable diagnostics and register behavior differ across DP83867 family options.
پێشنیارکراو
Test and Measurement Network Ports
The DP83867ISRGZT can provide a reliable Gigabit Ethernet service port on test equipment, analyzers, and measurement gateways. The combination of 10/100/1000 Mbit/s support allows the instrument to connect to laboratory networks operating at different speeds, while RGMII or SGMII permits integration with programmable logic or high-speed processors. Industrial-temperature operation is useful in automated production cells where temperature varies. The implementation should prioritize low-noise clocking, stable reference supplies, controlled return paths, and short Ethernet routes to the magnetics. Firmware and register compatibility must be checked when changing between DP83867 suffixes, particularly for cable diagnostics, autonegotiation behavior, and custom status reporting.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DP83867ISRGZT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DP83867IRRGZR | DP83867CSRGZT | DP83867ERGZR | DP83867ISRGZR | DP83867ISV |
|---|---|---|---|---|---|---|
| Package | 48-pin RGZ VQFN | 48-pin RGZ VQFN | 48-pin RGZ VQFN | 48-pin RGZ VQFN | 48-pin RGZ VQFN | 48-pin RGZ VQFN |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Ethernet Port Count | 1 port | 1 port | 1 port | 1 port | 1 port | 1 port |
| Supported Data Rates | 10/100/1000 Mbit/s | 10/100/1000 Mbit/s | 10/100/1000 Mbit/s | 10/100/1000 Mbit/s | 10/100/1000 Mbit/s | 10/100/1000 Mbit/s |
| Copper Ethernet Protocols | 10BASE-T, 100BASE-TX, 1000BASE-T | 10BASE-T, 100BASE-TX, 1000BASE-T | 10BASE-T, 100BASE-TX, 1000BASE-T | 10BASE-T, 100BASE-TX, 1000BASE-T | 10BASE-T, 100BASE-TX, 1000BASE-T | 10BASE-T, 100BASE-TX, 1000BASE-T |
| Host Interface | RGMII and SGMII | RGMII and SGMII | RGMII and SGMII | RGMII and SGMII | RGMII and SGMII | RGMII and SGMII |
| Interface Voltage Rails | 1.0 V, 1.8 V, and 2.5 V | 1.0 V, 1.8 V, and 2.5 V | 1.0 V, 1.8 V, and 2.5 V | 1.0 V, 1.8 V, and 2.5 V | 1.0 V, 1.8 V, and 2.5 V | 1.0 V, 1.8 V, and 2.5 V |
جیاکەرەوە سەرەکییەکان
- Explicit industrial-temperature operating class (بەراورد بەDP83867CSRGZT)
- Site-linked alternative within the same 48-pin RGZ family (بەراورد بەDP83867IRRGZR)
- Single PHY supports legacy and Gigabit copper links (بەراورد بەDP83867ERGZR)
- Parallel and serial host connectivity (بەراورد بەDP83867ISRGZR)
تێبینییەکانی دیزاین
Place the PHY close to the RJ45 connector and network transformer, and route the 1000BASE-T differential pairs as controlled-impedance traces with continuous reference planes. Keep the pairs short, symmetrical, and free of stubs. Separate switching-regulator paths and digital clocks from the analog PHY section. The manufacturer application guidance should be used for the exact separation, component placement, and exposed-pad land pattern because the 48-pin RGZ package provides a compact but layout-sensitive implementation.
Provide clean, independently decoupled analog and digital supplies according to the manufacturer power-supply recommendations. Keep high-current regulator paths away from the PHY and network magnetics, and connect the exposed pad as specified in the package drawing. Start with the datasheet’s required input and output capacitance, voltage tolerances, sequencing, and power-up limits rather than substituting generic bulk or ceramic values. This prevents supply ripple, startup failure, and unstable reference behavior.
RGMII and SGMII interfaces can be sensitive to clock jitter, return-path discontinuities, and source-synchronous timing violations. Use the manufacturer-recommended clock source and connection method, maintain continuous reference planes, and observe interface voltage levels before enabling the PHY. Account for trace length and skew at the host controller, and validate timing with the actual PCB stack-up. SGMII and RGMII are alternatives at the system level rather than signals to drive simultaneously without a defined operating mode.
Do not treat similarly suffixed DP83867 devices as unconditional substitutes. Check the exact temperature grade, qualification, register map, clocking, cable-diagnostic behavior, magnetic-module requirements, and exposed-pad implementation before changing the MPN. Also verify that the selected network transformer supports the intended data rates and isolation scheme. Software drivers should be tested against the replacement because link reporting and configuration behavior may differ even when the PCB footprint and broad PHY functions match.
زانیاری پابەندبوون
Compliance attributes were not established by the manufacturer page or product listing and must be confirmed through current TI product documentation before procurement or deployment.