DS90CF363AMTDX - 65MHz 21/3 LVDS FPD-Link Transceiver | TI
MPN: DS90CF363AMTDX ✓ چالاکDS90CF363AMTDX گشتی
A flat-panel display link, or FPD-Link, is a high-speed parallel-to-serial interface used to transfer pixel data and synchronization signals between a graphics controller and a display panel. In the system hierarchy, an FPD-Link transceiver sits between an LCD or digital display interface and an LVDS panel connection, combining several parallel data channels onto fewer differential pairs. This reduces wiring density while preserving the bandwidth required for high-resolution display panels.
The DS90CF363AMTDX provides 21 driver outputs and 3 receiver inputs in a single 48-TSSOP package. Its 3.0 V to 3.6 V operating supply supports 3.3 V display systems, while the 65 MHz operating specification supports pixel-clock rates commonly used with 18-bit flat-panel interfaces. The falling-edge LVDS transmitter architecture and selectable output configuration allow system designers to match panel timing and data-mapping requirements without changing the transceiver package.
The device is intended for use in flat-panel display systems, LCD monitors, digital signage controllers, industrial panel interfaces, and embedded graphics systems. The 48-TSSOP outline provides a standard surface-mount footprint suitable for compact controller boards. Tape-and-reel packaging supports automated assembly and high-volume production, while the three receiver channels support clock and control feedback paths where the connected panel or interface requires them.
Layout quality is critical in an LVDS link because differential trace mismatch, unequal pair lengths, and excessive stub lengths can degrade signal integrity at the 65 MHz operating rate. Route each LVDS differential pair as a tightly coupled pair over a continuous reference plane, avoid vias where possible, and place termination and interface components according to the manufacturer datasheet. Confirm that the selected panel connector and cable use the same data-channel mapping as the programmed transmitter configuration.
This page consolidates the verified interface, supply, speed, package, and sourcing information for DS90CF363AMTDX with application guidance, same-family alternatives, and practical LVDS layout considerations that help shorten design-in and troubleshooting work.
جێگرەوەکانی جێگۆڕکێ بۆ DS90CF363AMTDX — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ DS90CF363AMTDX (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
DS90CF363MTDX
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DS90CF363BMTX
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DS90CF363AMTD
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DS90CF363MT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DS90CF363BMT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DS90CF363AMTDX تایبەتمەندییەکان
| Product Type | LVDS FPD-Link Transceiver |
| Number of Drivers | 21 |
| Number of Receivers | 3 |
| Transmitter Type | Transmitter |
| Supply Voltage Range | 3 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| زۆرترین فرێکوێنسیی کاتژمێر | 65 MHz |
| Interface Protocol | FPD-Link |
| Signal Standard | LVDS |
| Edge Classification | Falling-edge LVDS transmitter |
| پاکێج | 48-TSSOP |
| Package Dimensions | 6.10 mm width x 0.240 inch body width |
| جۆری دامەزراندن | Surface Mount |
| Packaging | Tape and Reel (TR) |
ڕێنمایی ڕێکخستنی پینی DS90CF363AMTDX 6.10 mm width x 0.240 inch body width
ڕێکخستنی پین بۆ DS90CF363AMTDX (پاکێجی 6.10 mm width x 0.240 inch body width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ DS90CF363AMTDX.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
DS90CF363AMTDX گونجاوە بۆ 6 بەکارھێنانs: LCD Monitor Display-Link Controller, Industrial Flat-Panel Display Interface, Digital Signage Controller, Embedded Graphics and Panel Interface, Medical Panel Display Interface, Point-of-Sale Terminal Display.
LCD Monitor Display-Link Controller
The DS90CF363AMTDX fits a 3.3 V LCD monitor design that converts parallel pixel data into an LVDS flat-panel link. Its 21 driver outputs provide the channel resources needed by an 18-bit display interface, while the 3.3 V supply range and 65 MHz operating rate match common panel timing requirements. Configure the output mapping to match the target panel and verify differential routing, connector transitions, and receiver termination against the manufacturer application guidance.
پێشنیارکراو
Industrial Flat-Panel Display Interface
The DS90CF363AMTDX is suitable for an industrial panel controller operating from a regulated 3.3 V rail. The 48-TSSOP package provides a compact surface-mount implementation, and the 65 MHz FPD-Link transmitter function supports parallel-to-LVDS conversion for TFT displays. Because industrial systems often use long cables or strict EMC controls, maintain coupled LVDS routing, validate connector loss, and check the transmitter configuration against every panel data mapping.
پێشنیارکراو
Digital Signage Controller
A digital signage controller can use the DS90CF363AMTDX to bridge parallel graphics data and an LVDS panel input. Its 21 transmitters, 3 receivers, and 65 MHz clock capability fit the 18-bit flat-panel link class, while the 3.0 V to 3.6 V operating range simplifies integration with 3.3 V logic. Select the proper data arrangement for each display, and account for panel-specific timing, scaling, and cable length when qualifying the complete display chain.
پێشنیارکراو
Embedded Graphics and Panel Interface
The DS90CF363AMTDX can serve as the panel-link stage between an embedded graphics engine and an LVDS display. Its 48-TSSOP outline suits compact single-board designs, and the 3.3 V operating point integrates with modern display-controller logic. The transmitter must be programmed or strapped for the correct channel arrangement, and the board layout should use continuous reference planes and matched differential pairs to preserve margin at the 65 MHz operating limit.
پێشنیارکراو
Medical Panel Display Interface
The DS90CF363AMTDX can be evaluated for a medical display controller when the selected panel uses a compatible 18-bit FPD-Link and LVDS interface. Its 65 MHz transmitter rate, 21 outputs, and 3.3 V supply operation match many panel-controller architectures. Medical designs still require application-specific review of electrical safety, isolation, EMC, and panel timing; use the manufacturer datasheet for the exact pin, timing, and configuration requirements.
پێشنیارکراو
Point-of-Sale Terminal Display
Point-of-sale terminals frequently use compact TFT panels driven from a 3.3 V embedded controller. The DS90CF363AMTDX provides the parallel-to-LVDS conversion and 65 MHz operating capability needed for an 18-bit flat-panel link in a 48-TSSOP package. Because these products are cost-sensitive and often built in high volume, compare revision availability and assembly packaging carefully, and verify the connector and panel mapping before releasing a production layout.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ DS90CF363AMTDX — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | DS90CF363MTDX | DS90CF363BMTX | DS90CF363AMTD | DS90CF363MT | DS90CF363BMT |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TSSOP | 48-TSSOP - same | 48-TSSOP - same | 48-TSSOP - same | 48-TSSOP - same | 48-TSSOP - same |
| Device Function | LVDS FPD-Link Transceiver | LVDS FPD-Link Transceiver | 3.3 V falling-edge LVDS transmitter | LVDS FPD-Link Transceiver | LVDS FPD-Link Transmitter | LVDS FPD-Link Transmitter |
| Maximum Clock Frequency | 65 MHz | 65 MHz | 65 MHz | 65 MHz | 65 MHz | 65 MHz |
| Signal Standard | LVDS | LVDS | LVDS | LVDS | LVDS | LVDS |
| Interface Protocol | FPD-Link | FPD-Link | FPD-Link | FPD-Link | FPD-Link | FPD-Link |
| Flat-Panel Link Width | 18-bit | 18-bit | 18-bit | 18-bit | 18-bit | 18-bit |
جیاکەرەوە سەرەکییەکان
- Combines 21 LVDS drivers and 3 receivers in one display-link device (بەراورد بەDS90CF363BMTX)
- Directly matches an 18-bit flat-panel display link (بەراورد بەDS90CF363MTDX)
- Uses a 3.3 V supply in a compact surface-mount package (بەراورد بەDS90CF363BMTX)
- Established A-family ordering option for legacy display designs (بەراورد بەDS90CF363BMT)
تێبینییەکانی دیزاین
Route the LVDS outputs as tightly coupled differential pairs over a continuous reference plane. Keep intra-pair spacing consistent, match the pairs to the extent required by the link budget, and avoid unnecessary layer changes or stubs. At the 65 MHz operating rate, connector transitions and breakout regions should follow the geometry recommended in the manufacturer data sheet, and the return path beneath each pair should remain uninterrupted.
Verify the panel data mapping before enabling the transmitter because FPD-Link arrangements determine how parallel pixel and control signals appear on the LVDS outputs. Compare the configuration table for the exact ordering suffix, not only the product family name. Also check receiver inputs, clock polarity, and configuration straps against the schematic, since a mismatched arrangement can appear as missing pixels, scrambled data, or an unstable image.
Do not assume that every 48-TSSOP member in the DS90CF363 family is electrically interchangeable. Revision letters, configuration tables, timing limits, and packing suffixes can differ. Before substituting an orderable code, compare the pin descriptions, power-up sequence, output-mapping options, maximum clock rate, and absolute maximum ratings. Also confirm that the intended assembly process supports the selected tape-and-reel or other packing method.
Keep the LVDS interface away from high-slew-rate clocks, switch-mode power nodes, and noisy control lines where practical. Provide a quiet return path under the differential pairs and follow the manufacturer's recommended decoupling arrangement. If radiated-emissions problems appear, first inspect pair symmetry, connector shields, cable entry points, and chassis grounding rather than changing data rates or adding signal conditioning without first measuring the channel.
زانیاری پابەندبوون
Compliance declarations were not identified in the verified component records. Confirm the current RoHS, REACH, lead-free, and halogen-free status with the manufacturer for the exact ordering code before release.