EFM32TG825F8-BGA48T - 32MHz ARM MCU | Silicon Labs
MPN: EFM32TG825F8-BGA48T ✓ چالاکEFM32TG825F8-BGA48T گشتی
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one device. The EFM32TG825F8-BGA48T belongs to the Tiny Gecko family of 32-bit microcontrollers, combining the ARM Cortex-M3 architecture with energy-saving modes and fast wake-up behavior. This hierarchy places it above the Cortex-M3 core and within the broader embedded MCU and semiconductor categories.
The device operates from 1.98 V to 3.8 V and supports an industrial temperature range of -40°C to 85°C. Its operating frequency of 32 MHz provides useful processing performance for embedded control tasks, while the integrated AES accelerator, three operational amplifiers, LCD capability, and low-power architecture reduce the need for external discrete components. The 8 KB Flash configuration suits compact firmware and code-constrained embedded nodes.
Silicon Labs positions this MCU around energy-efficient operation, autonomous sensor monitoring in Deep Sleep Mode, capacitive sensing, and rapid wake-up from energy-saving states. Two 16-bit timers support periodic timing, motor-control-related timing, or general event counting. The Serial Wire Debug interface and pre-programmed UART bootloader support development, diagnostics, and field configuration without requiring a separate programming interface in the target application.
Typical uses include compact sensor nodes, capacitive buttons, low-power industrial monitors, small LCD instruments, wearable accessories, and embedded control modules. Its 37 I/O pins provide access to sensors and actuators, while the operational amplifiers can condition analog inputs close to the MCU. Designers should still verify each peripheral pin assignment against the device's pin multiplexing and board-level power requirements before finalizing a PCB.
The principal design trade-off is its 8 KB Flash limit. It works well for compact, event-driven firmware but may require careful code organization when the application includes extensive libraries, a bootloader, or complex communications stacks. The 3.8 V maximum supply also means the device is intended for low-voltage systems rather than direct connection to higher-voltage industrial rails.
This product record combines the manufacturer device information with package, memory, interface, and low-power design guidance. It also identifies same-family hardware alternatives, practical selection criteria, and engineering considerations that help teams determine whether this 48-BGA MCU fits their PCB and firmware requirements.
جێگرەوەکانی جێگۆڕکێ بۆ EFM32TG825F8-BGA48T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ EFM32TG825F8-BGA48T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Flash Memory, Package, Product Type, Series, RAM.
EFM32TG825F16-BGA48T
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →EFM32TG825F32-BGA48T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →EFM32TG225F8-BGA48T
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →EFM32TG225F32-BGA48T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
EFM32TG825F8-BGA48T زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Series | EFM32 Tiny Gecko |
| Processor Core | ARM Cortex-M3 |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 8 KB (8K x 8) |
| RAM | 2 KB |
| Digital I/O Pins | 37 pins |
| Timers | 2 x 16-bit timers |
| Supply Voltage Range | 1.98 V to 3.8 V |
| مەودای پلەی گەرمیی کارکردن | -40°C to +85°C |
| پاکێج | 48-BGA (4x4 mm) |
| جۆری دامەزراندن | Surface Mount |
| LCD Support | Up to 8x11 LCD |
| Security Accelerator | AES hardware |
| Operational Amplifiers | 3 integrated operational amplifiers |
| Debug Interface | 2-pin Serial Wire Debug |
| Bootloader | Pre-programmed UART bootloader |
| Power Features | Deep Sleep Mode, energy-saving modes, and fast wake-up |
ڕێنمایی ڕێکخستنی پینی EFM32TG825F8-BGA48T 48-bga (4x4 mm)
ڕێکخستنی پین بۆ EFM32TG825F8-BGA48T (پاکێجی 48-bga (4x4 mm)). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ EFM32TG825F8-BGA48T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
EFM32TG825F8-BGA48T گونجاوە بۆ 6 بەکارھێنانs: Low-Power Sensor Nodes, Capacitive Touch and Button Interfaces, Compact LCD Instruments, Industrial Monitoring and Control, Battery-Powered Wearable Accessories, AES-Protected Embedded Control.
Low-Power Sensor Nodes
The EFM32TG825F8-BGA48T fits autonomous sensor nodes that need responsive control with low standby consumption. Its 32 MHz ARM Cortex-M3 core can process measurements and handle communications logic, while Deep Sleep Mode and fast wake-up behavior support duty-cycled operation. The 8 KB Flash limit is suitable for compact acquisition, filtering, and protocol routines, and 37 I/O pins provide flexible sensor connections. Designers should use the datasheet's sleep-current figures to calculate battery life and confirm that the firmware fits within the 8 KB program area.
پێشنیارکراو
Capacitive Touch and Button Interfaces
The EFM32TG825F8-BGA48T can serve as the controller for capacitive buttons and compact human interfaces. Its 32 MHz processing capability supports debouncing, filtering, event detection, and interface updates, while the integrated operational amplifiers can support front-end signal conditioning. Silicon Labs identifies capacitive sensing and autonomous sensor monitoring as suitable uses for the platform. The 8 KB Flash footprint favors compact touch firmware rather than a graphical application, and the BGA48 package supports dense placement where PCB area is constrained.
پێشنیارکراو
Compact LCD Instruments
The EFM32TG825F8-BGA48T is suitable for small LCD-based measurement instruments because Silicon Labs specifies support for an 8x11 LCD and provides two 16-bit timers for periodic display or measurement updates. Its 32 MHz ARM Cortex-M3 core handles user-interface logic, while 2 KB of RAM supports short-lived display buffers. The 8 KB Flash capacity limits software size, making disciplined display and application code important. A 48-BGA footprint also allows the controller to be placed close to the display connector on compact assemblies.
پێشنیارکراو
Industrial Monitoring and Control
The EFM32TG825F8-BGA48T can serve as the local controller in a compact industrial monitoring module. Its 37 digital I/O pins allow connection of digital sensors, status inputs, and control outputs, while the three integrated operational amplifiers reduce the need for external analog conditioning in suitable signal ranges. The -40°C to 85°C temperature range supports industrial environments, and the 1.98 V to 3.8 V supply simplifies low-voltage rail design. Engineers must verify isolation, surge protection, and analog input limits at the system level.
پێشنیارکراو
Battery-Powered Wearable Accessories
The EFM32TG825F8-BGA48T is appropriate for small battery-powered wearable accessories where board area and standby energy are important. Its 48-BGA (4x4 mm) package minimizes occupied PCB area, while the Tiny Gecko low-power architecture supports Deep Sleep Mode and rapid wake-up for event-driven operation. The Cortex-M3 core manages sensing, simple user feedback, and low-rate data handling. The 8 KB Flash limit may constrain feature-rich firmware, so code budgeting is essential when adding wireless or storage functions.
پێشنیارکراو
AES-Protected Embedded Control
The EFM32TG825F8-BGA48T is useful in compact embedded controllers that require hardware-assisted AES encryption. Its integrated AES accelerator can offload supported cryptographic operations from the 32 MHz ARM Cortex-M3 core, helping preserve processing capacity for control tasks and communications. The device also provides Serial Wire Debug and a UART bootloader, which support development and field update workflows. Security design must still include secure key storage, boot protection, and protocol design because the presence of an AES peripheral alone does not secure the complete product.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ EFM32TG825F8-BGA48T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | EFM32TG825F16-BGA48T | EFM32TG825F32-BGA48T | EFM32TG225F8-BGA48T | EFM32TG225F32-BGA48T |
|---|---|---|---|---|---|
| Package | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) | 48-BGA (4x4 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Flash Memory | 8 KB | 16 KB | 32 KB | 8 KB | 32 KB |
جیاکەرەوە سەرەکییەکان
- Lowest Flash density in the compared EFM32TG825 BGA48 options (بەراورد بەEFM32TG825F16-BGA48T)
- Compact 48-BGA implementation for space-constrained boards (بەراورد بەEFM32TG225F8-BGA48T)
- Hardware-assisted AES and integrated analog resources (بەراورد بەEFM32TG225F32-BGA48T)
تێبینییەکانی دیزاین
Design the supply network around the 1.98 V to 3.8 V operating range and place the required decoupling capacitors close to the BGA48 power and ground balls. Account for voltage droop when the 32 MHz core becomes active, especially in battery designs where the source impedance rises as the cell discharges. Use separate return paths for quiet analog and digital loads where possible, and verify the operating voltage across temperature rather than relying only on a nominal 3.3 V rail.
The 48-BGA (4x4 mm) package requires a dense escape-routing strategy. Use the manufacturer's recommended land pattern and route power, ground, SWD, and communication signals on multiple PCB layers where required. Keep BGA vias beneath the device where the footprint permits, inspect the finished board with X-ray methods when necessary, and confirm that the assembly profile accommodates the 0.5 mm pitch ball array without interfering with neighboring components.
Do not select this 8 KB Flash variant before checking the final linked binary and library footprint. Features such as the UART bootloader, cryptographic routines, and application code all consume the same 8 KB program area. For a firmware build near the limit, choose EFM32TG825F16-BGA48T or EFM32TG825F32-BGA48T. Also confirm that every BGA48 signal assigned in the schematic is supported by the selected peripheral instance and alternate-function mapping.
Route the two-wire Serial Wire Debug interface away from fast-switching nodes and provide clear ground returns for the debugger and target. If UART bootloading is used, ensure the communication pins do not conflict with the production firmware or external circuitry at reset. Because the BGA package offers many alternate functions, review pin multiplexing early; changing an assignment late in the PCB layout can require additional escape routing or a board respin.
زانیاری پابەندبوون
The manufacturer and distributor descriptions do not state the requested RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. This MCU is not presented as an automotive-qualified device, so AEC-Q100 is recorded as not applicable.