Microchip Technology

ENC28J60/SO - 10BASE-T SPI Ethernet Controller | Microchip

MPN: ENC28J60/SO ✓ چالاک
3.1 V to 3.6 V Vdss 160 mA Id 28-pin SOIC, 0.295 inch / 7.50 mm width Package 10 Mb/s Speed
MOQ: 1 |

ENC28J60/SO گشتی

The Microchip Technology ENC28J60/SO is a stand-alone 10BASE-T Ethernet controller with an integrated IEEE 802.3 MAC and physical layer, an SPI host interface, 8 KB of dual-port packet-buffer SRAM, internal DMA, and hardware-assisted checksum calculation. The device operates from a 3.1 V to 3.6 V supply, consumes 160 mA as listed in the verified distributor specifications, and is packaged in a 28-pin SOIC.

An Ethernet controller is an interface integrated circuit that connects a microcontroller or embedded processor to a physical network. Within the product hierarchy, the ENC28J60 is a network interface controller and Ethernet interface IC. It implements the lower-level MAC and PHY functions required for 10BASE-T networking, while the connected host processor must provide the upper-layer networking functions. The SPI interface allows the device to be used with embedded systems that do not include an Ethernet media-access controller.

Key features include IEEE 802.3 compatibility, an integrated 10BASE-T PHY, an 8 KB transmit-and-receive packet buffer, programmable packet filtering, internal DMA for packet throughput, and hardware-assisted checksum calculation. Two LED outputs provide link and network-activity indication. A 25 MHz crystal is required for the oscillator, and the manufacturer specifies a parallel-resonance crystal in the oscillator circuit.

The controller combines hardware packet movement and filtering with a host-driven SPI protocol. Its internal DMA helps move packet data without requiring the host controller to handle every byte through the serial interface. The 8 KB SRAM supports buffering for received and transmitted Ethernet frames, while programmable filters can limit which destination addresses or packet types are accepted. Hardware-assisted checksums reduce host-processing requirements for supported network protocols.

Typical uses include embedded web servers, industrial monitoring equipment, building-automation nodes, environmental data loggers, and compact IoT gateways. The ENC28J60 is most appropriate when only 10 Mb/s Ethernet is required and the host has enough flash and processing capacity to run a TCP/IP stack. It is less appropriate where 100 Mb/s operation or an integrated hardware TCP/IP stack is required without redesign.

Designers should place the 25 MHz crystal and its required load components close to OSC1 and OSC2, route the Ethernet magnetics and network interface carefully, and follow the manufacturer datasheet for termination, decoupling, and exposed-pad or thermal-layout requirements. Because the exact verified pin assignments were not included in the supplied source data, this page does not publish a potentially inaccurate pinout.

This page consolidates the verified manufacturer and distributor information, distinguishes genuine same-package alternatives from functional substitutes, and adds practical selection guidance and engineering caveats beyond the basic catalogue listing.

جێگرەوەکانی جێگۆڕکێ بۆ ENC28J60/SO — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ENC28J60/SO (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Ethernet Standard, Package, Buffer RAM, Ethernet Speed, Host Interface.

Microchip Technology
Ethernet Standard: IEEE 802.3 compatible
Package: 28-pin SOIC
Buffer RAM: 8 KB transmit/receive packet dual-port buffer SRAM
Microchip Technology
Ethernet Standard: 10BASE-T
Package: 28-pin SSOP
Buffer RAM: 8 KB

ENC28J60-I/SO

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 28-pin SOIC, 0.295 inch / 7.50 mm width
Stand-alone Ethernet controller with SPI interface · IEEE 802.3 compatible · 10BASE-T, 10 Mb/s · Yes · Yes, 10BASE-T PHY · SPI serial interface · 8 KB transmit/receive packet dual-port buffer SRAM · 3.1 V to 3.6 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ENC28J60/SO تایبەتمەندییەکان

Controller Type Ethernet Controller
Ethernet Standard IEEE 802.3
Integrated Layers MAC and 10BASE-T PHY
Host Interface SPI
Ethernet Speed 10 Mb/s
Supply Voltage Range 3.1 V to 3.6 V
ئێستای دابینکردن 160 mA
Packet Buffer RAM 8 KB
Buffer Architecture Dual-port transmit/receive packet buffer
DMA Internal
Checksum Assistance Hardware-assisted checksum calculation
Packet Filtering Programmable
Status Indicators Two LEDs for link and network activity
Oscillator Frequency 25 MHz
Oscillator Crystal Type Parallel-resonance crystal
پاکێج 28-pin SOIC, 0.295 inch / 7.50 mm width
جۆری دامەزراندن Surface Mount

ڕێنمایی ڕێکخستنی پینی ENC28J60/SO 28-pin soic, 0.295 inch / 7.50 mm width

ڕێکخستنی پین بۆ ENC28J60/SO (پاکێجی 28-pin soic, 0.295 inch / 7.50 mm width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 28-pin soic, 0.295 inch / 7.50 mm width بۆ ENC28J60/SO

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ENC28J60/SO.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ENC28J60/SO گونجاوە بۆ 6 بەکارھێنانs: Embedded Web Server, Industrial Sensor Gateway, Environmental Data Logger, Building Automation Controller, Remote Monitoring Unit, IoT Control Node.

🌐

Embedded Web Server

The ENC28J60/SO fits an embedded web server that must expose status, configuration, or sensor information over a 10 Mb/s wired network. Its SPI interface connects efficiently to a host microcontroller, while the integrated 10BASE-T PHY removes a separate physical-layer device. The 8 KB packet buffer and internal DMA support packet handling without requiring the host to move every Ethernet byte through software GPIO operations. The principal trade-off is that the host must provide the required TCP/IP and HTTP services; when many concurrent users or large transfers are expected, a controller with 100 Mb/s performance and hardware protocol offload is more appropriate.

🏭

Industrial Sensor Gateway

The ENC28J60/SO can connect an industrial sensor gateway to an Ethernet network when 10 Mb/s throughput is sufficient. Its 3.1 V to 3.6 V operating range fits regulated embedded systems, and the integrated IEEE 802.3 MAC and 10BASE-T PHY simplify the network hardware. Programmable packet filtering, internal DMA, and hardware-assisted checksum calculation reduce host-side processing. The controller still requires external Ethernet magnetics, a 25 MHz parallel-resonance crystal, suitable decoupling, and a host-side network stack, so it is best suited to distributed monitoring nodes rather than high-bandwidth factory data aggregation.

🧩

Environmental Data Logger

For an environmental data logger, the ENC28J60/SO provides a compact path from a low-power microcontroller to a wired Ethernet network. The 8 KB dual-port packet buffer supports network packet buffering, while the SPI host interface allows the controller to operate alongside sensors and local storage. Its 10 Mb/s capability is more than adequate for periodic measurements, status packets, and administrative traffic. The system designer must balance network availability against low-power goals, account for the listed 160 mA supply current during operation, and validate the Ethernet implementation for the required industrial or environmental temperature range.

🏠

Building Automation Controller

The ENC28J60/SO is suitable for building-automation controllers that distribute control commands, diagnostics, and occupancy or environmental data over a 10BASE-T network. Programmable packet filters can reduce acceptance of unnecessary traffic, while link and activity LED outputs support local cabinet diagnostics. The compact 28-pin SOIC format and SPI interface make it practical for a controller PCB that also includes a microcontroller and isolated communications hardware. Because ENC28J60/SO is a 10 Mb/s controller with no verified hardware TCP/IP stack, it is best for moderate control traffic rather than video, high-rate building systems, or heavily loaded networks.

📡

Remote Monitoring Unit

A remote monitoring unit can use the ENC28J60/SO to deliver alarms, measurements, and diagnostic records over a wired Ethernet link. The integrated MAC and PHY reduce the external interface circuit to the required Ethernet transformer, passive components, and approved magnetics, while the SPI interface gives the host processor a straightforward command and status path. Its internal DMA and checksum assistance are useful when periodic records must coexist with control traffic. Designers should provide a 3.3 V supply with suitable decoupling, implement the manufacturer's 25 MHz crystal circuit carefully, and select an Ethernet topology and surge-protection strategy appropriate to the installation environment.

🧩

IoT Control Node

The ENC28J60/SO provides a wired-network option for an IoT control node that needs a compact SPI Ethernet interface without a dedicated Ethernet MAC in the host microcontroller. Its 8 KB packet RAM, programmable filters, and internal DMA make the device useful for command processing and telemetry. The 10 Mb/s speed suits typical device-management traffic but can become a bottleneck for image updates, large diagnostic files, or multiple data streams. Because upper-layer protocol support remains a host-software responsibility, firmware developers should verify memory budget, interrupt latency, TCP/IP performance, and driver availability before selecting this architecture.

What is the ENC28J60/SO and what does it do?
The ENC28J60/SO is a Microchip Technology stand-alone Ethernet controller that combines an IEEE 802.3 MAC, a 10BASE-T PHY, and an SPI host interface in a 28-pin SOIC package. According to the manufacturer datasheet, it also provides 8 KB of packet-buffer SRAM, internal DMA, programmable packet filtering, and hardware-assisted checksum calculation. It is designed for embedded systems that require 10 Mb/s wired Ethernet and a host-supplied TCP/IP stack.
What are the key specifications of ENC28J60/SO that engineers should know?
The ENC28J60/SO combines a 10BASE-T PHY, IEEE 802.3 MAC, SPI interface, and 8 KB dual-port packet buffer. According to the manufacturer datasheet, its supply range is 3.1 V to 3.6 V, the listed supply current is 160 mA, and its oscillator uses a 25 MHz parallel-resonance crystal. The 28-pin SOIC package is suitable for surface-mount industrial, networking, and embedded-control designs.
What is the operating voltage of ENC28J60/SO?
The ENC28J60/SO operates from 3.1 V to 3.6 V according to the verified distributor specifications and manufacturer datasheet. This makes the device appropriate for embedded systems using a regulated 3.3 V rail. The controller's listed supply current is 160 mA, so power planning should include both the controller and the current required by the associated Ethernet magnetics and external circuitry.
Does ENC28J60/SO support 100 Mb/s Ethernet?
No. The ENC28J60/SO provides an integrated 10BASE-T PHY and supports Ethernet operation up to 10 Mb/s. The manufacturer identifies the device as IEEE 802.3 compatible, but the supplied specifications do not identify it as a 100BASE-T controller. Designs requiring 100 Mb/s should use a controller that explicitly specifies 100 Mb/s rather than treating this device as a direct substitute.
How much packet memory does ENC28J60/SO contain?
The ENC28J60/SO contains 8 KB of dual-port transmit and receive packet-buffer SRAM. According to the manufacturer product page and datasheet, this SRAM works with the internal DMA to move Ethernet packet data efficiently. The available buffer must be managed by the host and network software, so applications should account for packet size and concurrent traffic when selecting this controller.
What crystal does ENC28J60/SO require?
The ENC28J60/SO requires a 25 MHz crystal connected between OSC1 and OSC2. The manufacturer datasheet specifically calls for a parallel-resonance crystal and warns against using a series-resonance crystal because it can produce an oscillator frequency outside the crystal manufacturer's specifications. Follow the datasheet oscillator circuit for the crystal load capacitance and component selection.
Where can I download the ENC28J60/SO datasheet PDF?
The ENC28J60/SO datasheet PDF is available from the official Microchip download link at https://ww1.microchip.com/downloads/en/DeviceDoc/39662e.pdf. The document is the appropriate source for the complete pin descriptions, electrical characteristics, register map, initialization sequence, oscillator requirements, and recommended application circuit. The supplied verification data confirms the official 25 MHz crystal guidance.
Where can I find the ENC28J60/SO pinout?
The ENC28J60/SO pinout is published in the official Microchip datasheet rather than in the supplied distributor summaries. The verified device is a 28-pin SOIC and includes SPI, oscillator, power, ground, Ethernet, and LED-related connections. Because the exact numbered pin list was not included in the verified data, this page uses a null pinout rather than guessing pin numbers; consult the official datasheet before PCB layout or replacement work.
What is the best drop-in replacement for ENC28J60/SO?
ENC28J60-I/SO is the strongest verified same-package candidate for ENC28J60/SO. It uses the same 28-pin SOIC format and the same Ethernet controller, 10BASE-T PHY, SPI interface, and 8 KB buffer concept, while the -I suffix denotes a distinct ordering variant. Because the supplied data does not provide full electrical tables or a formal cross-reference for additional devices, no other part should be treated as a guaranteed drop-in replacement without schematic verification.
Can ENC28J60-I/SO replace ENC28J60/SO without changing the PCB?
ENC28J60-I/SO is a same-package candidate because both devices are identified as 28-pin SOIC Ethernet controllers with an SPI interface, 10BASE-T PHY, and 8 KB packet RAM. A board-level replacement still requires checking the exact ordering-temperature information, pin assignments, and electrical limits in the manufacturer datasheet. The verified data does not establish that every temperature grade has identical limits, so validation remains required.
What can replace ENC28J60/SO?
ENC28J60-I/SO is the only replacement candidate in the supplied cross-reference data that is clearly identified with the same 28-pin SOIC package and closely matching Ethernet-controller functions. Other ENC28J60 package options, including ENC28J60/SS and ENC28J60/ML, are excluded because their package identifiers indicate different physical formats. Devices such as W5500, DM9051, and ENC424J600 are functional alternatives rather than guaranteed drop-in replacements.
ENC28J60/SO vs ENC28J60-I/SO: which is better?
ENC28J60-I/SO is the better candidate when an existing 28-pin SOIC design requires a same-package sourcing option. Both parts are presented as Microchip Ethernet controllers with a 10BASE-T PHY, SPI interface, and 8 KB RAM, but the verified snippets do not provide a complete temperature-grade comparison. Review the orderable-part table and absolute maximum and recommended operating conditions before deciding between them.
When should I choose ENC28J60/SO instead of a 100 Mb/s Ethernet controller?
Choose ENC28J60/SO when the application can operate at 10 Mb/s, the host microcontroller has sufficient flash and processing capacity for the required TCP/IP stack, and a compact SPI-connected Ethernet solution is valuable. It is especially useful for embedded monitoring, control, and data-logging equipment. For bulk transfers, multiple high-rate streams, or designs requiring hardware TCP/IP offload, a controller with explicit 100 Mb/s capability is preferable.
Is ENC28J60/SO suitable for industrial and IoT equipment?
The ENC28J60/SO is suitable for many embedded industrial and IoT designs that require 10BASE-T connectivity and can accommodate a 28-pin surface-mount controller. Its 3.1 V to 3.6 V supply range, 8 KB packet buffer, DMA, filtering, and SPI interface support integration with microcontrollers. For deployments requiring 100 Mb/s, extended-temperature qualification, or a preinstalled TCP/IP stack, verify those requirements separately.
Where to buy ENC28J60/SO online?
ENC28J60/SO can be found through authorized distributors such as DigiKey and Mouser, while the official Microchip product page supports direct product and design-in information. The verified distributor records were captured on 2026-10-28, but the supplied snippets do not include a numeric unit price or confirmed stock quantity. Request a current quotation before purchasing, and use the official manufacturer ordering information to confirm package, temperature, and lifecycle options.
What is the price of ENC28J60/SO?
No verified numeric price for ENC28J60/SO was included in the supplied distributor data as of 2026-10-28, so the tier prices shown on this page are zero-value placeholders and are not purchase quotes. DigiKey, Mouser, Octopart, and Microchip Direct are listed as useful sourcing references, but their live amount, currency, stock, and lead time must be confirmed at the time of order. This avoids presenting an invented price as a current market fact.
What is the lead time and stock status for ENC28J60/SO?
The supplied verification does not explicitly state the quantity in stock or a guaranteed lead time for ENC28J60/SO. A DigiKey search result says the related ENC28J60-I/SO listing ships today, but that statement cannot be assigned to the non-I ordering code without confirming the exact distributor entry. As of 2026-10-28, request a live quotation and stock confirmation for the exact MPN before committing the production build.
Is ENC28J60/SO RoHS and REACH compliant?
The supplied verified data does not explicitly state the RoHS, REACH, lead-free, halogen-free, or conflict-minerals status of ENC28J60/SO, so those fields remain unknown. The Microchip product page and datasheet are the appropriate sources for current compliance declarations. Engineers requiring a documented compliance statement for procurement or deployment should request the current manufacturer material-declaration or product-compliance record.

داتای سەرچاوەی ئەندازیاری بۆ ENC28J60/SO — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose ENC28J60/SO when the design needs a small, SPI-connected 10BASE-T Ethernet interface and the host microcontroller can run the required TCP/IP stack. Its integrated MAC and PHY, 8 KB packet buffer, internal DMA, filtering, and checksum assistance are attractive for monitoring, industrial control, building automation, and compact embedded servers. ENC28J60-I/SO is the closest verified same-package alternative when an ordering variant is needed, although the exact temperature and electrical details should be checked before substitution. ENC28J60/SS and ENC28J60/ML are not drop-in options because their package identifiers differ. W5500, DM9051, and ENC424J600 should be treated as functional alternatives: they can address different speed, protocol-offload, or footprint requirements, but the supplied data explicitly indicates that pinout or driver changes may be necessary. For sustained bulk transfer, 100 Mb/s networking, or minimal host networking software, select a controller with those capabilities rather than forcing the ENC28J60 architecture.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ENC28J60-I/SO
Brand Microchip Technology Microchip Technology
Package 28-pin SOIC, 0.295 inch / 7.50 mm width 28-pin SOIC
Controller Type Ethernet Controller Ethernet Controller
Ethernet Interface 10BASE-T PHY 10BASE-T PHY
Host Interface SPI SPI
Packet Buffer RAM 8 KB 8 KB
Packet Filtering Programmable Programmable

جیاکەرەوە سەرەکییەکان

  • Integrated Ethernet MAC and physical layer (بەراورد بەFunctional alternatives requiring a separate PHY)
  • Hardware-assisted network processing (بەراورد بەSPI Ethernet designs using only host-managed packet movement)
  • Compact system integration (بەراورد بەControllers requiring separate external MAC and PHY devices)

تێبینییەکانی دیزاین

Route the ENC28J60/SO oscillator network as a compact, tightly coupled analog layout. Place the 25 MHz parallel-resonance crystal and its load components directly beside OSC1 and OSC2, maintain a short ground return, and avoid routing SPI, Ethernet, or switching-node traces beneath the oscillator area. The manufacturer datasheet specifically warns against a series-resonance crystal because it may shift the oscillator outside the crystal manufacturer's frequency specification.

Implement the Ethernet network interface using the manufacturer-recommended 10BASE-T magnetic isolation and passive network, then provide local supply decoupling according to the datasheet. Keep the ENC28J60/SO and its support components away from high-current switching nodes and noisy digital return paths. Validate the completed layout for Ethernet signal integrity, surge immunity, return loss, and radiated emissions rather than treating the digital side of the circuit as the only design consideration.

Do not assume that an Ethernet controller supplies the complete TCP/IP stack. ENC28J60/SO implements the MAC and 10BASE-T PHY and provides DMA, filtering, and checksum assistance, but the host must run the selected upper-layer network software. Check processor flash, RAM, interrupt latency, and driver maturity against realistic concurrent traffic before committing to a 10 Mb/s design, particularly when large files or multiple clients are involved.

Budget the ENC28J60/SO rail for the verified 160 mA supply current plus the current consumed by associated circuitry, and follow the manufacturer's recommended operating range of 3.1 V to 3.6 V. If the host system uses a switched 3.3 V source, confirm startup sequencing, voltage tolerance, and transient performance with the actual regulator and load arrangement. The zero values shown in the pricing tiers are data placeholders, not power or cost estimates.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied verified manufacturer and distributor data does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this product is an Ethernet interface controller rather than an automotive-qualified device.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ENC28J60/SO ENC28J60/SO datasheet Microchip ENC28J60/SO ENC28J60 28 pin SOIC Ethernet controller ENC28J60 3.1V to 3.6V 160mA ENC28J60 8KB packet buffer SPI ENC28J60/SO embedded web server ENC28J60/SO industrial sensor gateway ENC28J60/SO vs ENC28J60-I/SO ENC28J60/SO drop-in replacement ENC28J60/SO buy online ENC28J60/SO price and lead time where to find ENC28J60/SO pinout what can replace ENC28J60/SO

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology ENC28J60/SO ENC28J60-I/SO ENC28J60/SS ENC28J60/ML ENC424J600 W5500 DM9051 Ethernet controller network interface controller Ethernet interface IC IEEE 802.3 MAC 10BASE-T PHY SPI 10 Mb/s Ethernet 8 KB packet-buffer SRAM dual-port packet buffer internal DMA hardware-assisted checksum calculation programmable packet filtering 25 MHz parallel-resonance crystal 28-pin SOIC SOIC package family surface-mount package 3.1 V to 3.6 V power supply 10BASE-T Ethernet magnetics embedded web server
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ