Microchip Technology

ENC28J60/SP - 10BASE-T Ethernet Controller | Microchip

MPN: ENC28J60/SP ✓ چالاک
3.1 V to 3.6 V Vdss 160 mA Id 28-pin DIP, 0.300 inch, 7.62 mm Package 25 MHz Speed
MOQ: 1 |

ENC28J60/SP گشتی

The Microchip Technology ENC28J60/SP is a standalone Ethernet controller with an integrated 10BASE-T PHY, a 3.1 V to 3.6 V supply range, an SPI host interface, and a 28-pin DIP package. It combines a 10BASE-T media access controller with 8 KB of transmit and receive packet buffer SRAM, hardware-assisted checksum calculation, and an internal DMA module for embedded networking designs.

An Ethernet controller is an interface integrated circuit that connects a host processor to a physical Ethernet network. The ENC28J60 integrates the media access controller, 10BASE-T physical layer, packet memory, and serial host interface, allowing a microcontroller or other SPI-capable processor to communicate through a single Ethernet connector and magnetic interface. This integrated architecture is a member of the interface IC, Ethernet controller, and network interface controller hierarchy.

The device supports IEEE 802.3-compatible 10BASE-T operation, full-duplex and half-duplex communication, and an SPI interface for host access. Its 8 KB packet buffer reduces the amount of data that the host processor must handle directly, while internal DMA and hardware-assisted checksum calculation improve packet-processing efficiency. Two LEDs provide link and network-activity indication.

The ENC28J60 is designed around a 25 MHz crystal oscillator connected through OSC1 and OSC2. The manufacturer datasheet specifically calls for a parallel-resonance crystal, making oscillator-component selection and layout important to the stability of Ethernet timing. The controller accepts a 3.1 V to 3.6 V supply and is intended for embedded industrial automation, building automation, home control, security, and VoIP equipment.

Typical implementations place the ENC28J60 beside a 10BASE-T magnetic jack and connect it to a microcontroller through SPI. The host driver manages Ethernet registers, interrupts, packet buffers, and the physical layer. Compared with discrete Ethernet solutions, the integrated MAC and PHY reduce board area and component count while retaining a software-controlled packet-processing architecture.

PCB implementation should keep the 25 MHz crystal and its load components close to OSC1 and OSC2, provide the required bypass capacitance at the supply pins, and follow the manufacturer layout guidance for the integrated PHY and magnetic-jack interface. The 28-pin DIP package favors through-hole prototyping, but production designs may require a smaller surface-mount package variant.

This page combines verified manufacturer and distributor information, sourcing details, application guidance, and an honest assessment of drop-in replacement options. It is intended to help engineers determine whether the ENC28J60/SP fits the required electrical, mechanical, firmware, and supply-chain constraints.

جێگرەوەکانی جێگۆڕکێ بۆ ENC28J60/SP — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ ENC28J60/SP (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Integrated PHY, Package, Ethernet Standard, Host Interface, Mounting Type.

Microchip Technology
Integrated PHY: Yes, 10BASE-T PHY
Package: 28-pin SOIC
Host Interface: SPI serial interface
Microchip Technology
Integrated PHY: Yes
Package: 28-pin SPDIP
Ethernet Standard: 10BASE-T

ENC28J60-I/SP

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 28-pin DIP
Stand-alone Ethernet controller · 10BASE-T · 10 Mbps · Yes · Yes · 8 Kbytes · SPI serial interface · 3.1 V to 3.6 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ENC28J60/SP تایبەتمەندییەکان

Product Type Standalone Ethernet controller with SPI interface
Ethernet Standard IEEE 802.3 compatible
Integrated PHY 10BASE-T PHY
Integrated MAC Yes
Host Interface SPI
Supply Voltage Range 3.1 V to 3.6 V
ئێستای دابینکردن 160 mA
Packet Buffer SRAM 8 KB
Operating Modes Full-duplex and half-duplex 10BASE-T
DMA Internal DMA module
Checksum Hardware-assisted checksum calculation
Packet Filtering Programmable packet filtering schemes
Status Indication Two LEDs for link and network activity indication
Oscillator Frequency 25 MHz
Oscillator Type Parallel-resonance crystal
Oscillator Connections OSC1 and OSC2
پاکێج 28-pin DIP, 0.300 inch, 7.62 mm
جۆری دامەزراندن Through-hole
Packaging Tube
Operating Temperature Class Industrial
دۆخی RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

ڕێنمایی ڕێکخستنی پینی ENC28J60/SP 28-pin dip, 0.300 inch, 7.62 mm

ڕێکخستنی پین بۆ ENC28J60/SP (پاکێجی 28-pin dip, 0.300 inch, 7.62 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 28-pin dip, 0.300 inch, 7.62 mm بۆ ENC28J60/SP

هیچ داتای وردی پینئاوت بەردەست نییە بۆ ENC28J60/SP.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

ENC28J60/SP گونجاوە بۆ 6 بەکارھێنانs: Industrial Automation Controller, Building Automation Gateway, Home Control and IoT Node, Security and Surveillance Terminal, VoIP and Voice Network Endpoint, Data Logger and Sensor Gateway.

🏭

Industrial Automation Controller

The ENC28J60/SP fits industrial automation nodes that require a self-contained 10BASE-T Ethernet interface without adding a separate Ethernet PHY. Its 3.1 V to 3.6 V operating range, SPI host interface, internal DMA, and 8 KB packet buffer allow a microcontroller to exchange real-time process data while the hardware-assisted checksum calculation reduces host processing overhead. The device should be paired with an appropriate 10BASE-T magnetic jack and short, carefully routed copper connections. For products exposed to extended temperatures, the industrial-grade ENC28J60-I/SP is the better sourcing choice.

🏠

Building Automation Gateway

The ENC28J60/SP is appropriate for building-automation gateway and room-controller designs using 10BASE-T Ethernet. The integrated MAC and PHY reduce the number of external network components, while the 28-pin DIP package simplifies through-hole prototypes and legacy controller boards. Its 8 KB packet buffer and internal DMA provide a practical path for telemetry, configuration, and status traffic controlled over SPI. Designers should account for the slower 10 Mb/s Ethernet capability, use a 25 MHz parallel-resonance crystal as specified, and validate the magnetic-jack layout before production.

🧩

Home Control and IoT Node

The ENC28J60/SP can provide wired Ethernet connectivity for home-control, smart-building, and small IoT nodes that cannot depend continuously on a wireless link. Its SPI connection suits a microcontroller-based architecture, and the integrated 10BASE-T MAC and PHY simplify the physical-layer implementation. The controller operates from 3.1 V to 3.6 V and provides 8 KB of packet buffer SRAM for short network transactions. Its 10 Mb/s throughput is adequate for telemetry and control traffic, but the product must use a properly designed magnetic interface and controlled 25 MHz crystal circuit.

🎥

Security and Surveillance Terminal

The ENC28J60/SP can support low-bandwidth security and surveillance equipment such as access-control terminals, alarm panels, and camera-interface gateways that need deterministic Ethernet connectivity. The internal DMA, hardware-assisted checksum calculation, and 8 KB packet buffer allow the host processor to concentrate on control tasks rather than copying every Ethernet frame. The SPI host interface also allows the controller to be placed near a 10BASE-T magnetic jack while the processor remains elsewhere on the board. System designers must consider the 10 Mb/s limit, implement sensible frame sizing, and provide surge protection appropriate to the installation environment.

🌐

VoIP and Voice Network Endpoint

The ENC28J60/SP is suitable for VoIP and voice-network endpoints where an embedded processor needs a low-cost 10BASE-T network connection alongside its real-time control workload. The integrated MAC and PHY, SPI interface, internal DMA, and 8 KB packet buffer provide a compact implementation without a separate Ethernet physical-layer device. Because 10BASE-T performance is lower than Fast Ethernet, the firmware should use appropriately sized packet buffers and avoid unnecessarily large frame processing. The design must also use the specified 25 MHz parallel-resonance crystal and follow the manufacturer reference layout.

📡

Data Logger and Sensor Gateway

The ENC28J60/SP can connect an embedded data logger or sensor gateway to a 10BASE-T network using an SPI host processor. Its 3.1 V to 3.6 V supply range, internal DMA, and hardware-assisted checksum calculation help separate packet handling from acquisition and control work. The 8 KB packet buffer is useful for short telemetry messages and management packets, although designers should confirm that buffering and throughput satisfy the expected reporting interval. A robust deployment should include the industrial-grade ENC28J60-I/SP when required and follow the magnetic-jack and crystal-layout guidance in the manufacturer data sheet.

What is the operating voltage of ENC28J60/SP?
The Microchip Technology ENC28J60/SP operates from 3.1 V to 3.6 V. According to the manufacturer data sheet and the verified distributor specifications, the controller is designed for a 3.3 V-class embedded Ethernet supply. Designers should ensure that every rail connected to the device remains inside this range, while accounting for the stated 160 mA supply current. The 28-pin DIP package also requires suitable bypass capacitance and clean routing from the 3.3 V supply to the device.
What are the key specifications of ENC28J60/SP that engineers should know?
The ENC28J60/SP integrates an IEEE 802.3-compatible MAC, a 10BASE-T PHY, an SPI interface, 8 KB of packet buffer SRAM, internal DMA, and hardware-assisted checksum calculation. According to the Microchip Technology manufacturer data sheet, it operates from 3.1 V to 3.6 V, uses a 25 MHz parallel-resonance crystal, and is supplied in a 28-pin DIP package. These characteristics make it suitable for compact embedded Ethernet designs driven by a general-purpose microcontroller.
Where can I download the ENC28J60/SP datasheet PDF?
The official ENC28J60/SP data sheet can be downloaded from the Microchip Technology document link at https://ww1.microchip.com/downloads/en/DeviceDoc/39662e.pdf. It contains the electrical characteristics, register model, pin descriptions, application information, and recommended oscillator and layout details. The verified manufacturer page at https://www.microchip.com/en-us/product/ENC28J60 is also the appropriate starting point for current product information and supporting documentation.
Where can I find the ENC28J60/SP pinout?
The ENC28J60/SP pinout is documented in the pin-description section of the official Microchip Technology manufacturer data sheet at https://ww1.microchip.com/downloads/en/DeviceDoc/39662e.pdf. The supplied search data confirms the 28-pin DIP package but does not expose the complete numbered pin list, so this page does not reproduce potentially inaccurate pin assignments. Designers should use the manufacturer document and its package drawing when assigning OSC1, OSC2, SPI, power, interrupt, reset, and 10BASE-T connections.
What can replace ENC28J60/SP as a drop-in part?
The verified drop-in candidate for the ENC28J60/SP is the Microchip Technology ENC28J60-I/SP, which uses the same 28-pin DIP footprint and retains the 3.1 V to 3.6 V supply, 10BASE-T MAC and PHY, 8 KB SRAM, and SPI interface. Its primary distinction is the industrial temperature grade. The supplied cross-reference results do not verify additional distinct same-package replacements, so components in smaller packages or with different pinouts should not be described as drop-in substitutes.
Is ENC28J60/SP the same as ENC28J60-I/SP?
The ENC28J60/SP and ENC28J60-I/SP share the same core Ethernet-controller configuration and the verified 28-pin DIP package, but the -I ordering option identifies the industrial temperature-grade version. According to the verified comparison information, both provide an integrated 10BASE-T MAC and PHY, 8 KB packet RAM, and an SPI interface. Confirm the complete numerical temperature limits in the manufacturer data sheet before substituting one grade for the other.
ENC28J60/SP vs ENC28J60-I/SP - which is better for an industrial product?
The ENC28J60-I/SP is generally the better choice when the design requires the industrial temperature grade, while both devices otherwise retain the verified 28-pin DIP package, 3.1 V to 3.6 V supply range, 10BASE-T interface, 8 KB packet RAM, and SPI connection. According to the Microchip Technology manufacturer data sheet and distributor comparison data, the distinction is temperature grade rather than Ethernet functionality. The exact numerical operating limits should be checked before final qualification.
When should I choose ENC28J60/SP over a smaller SPI Ethernet controller?
Choose the ENC28J60/SP when a through-hole 28-pin DIP layout, a 10BASE-T PHY, and an SPI host interface are required in a cost-sensitive embedded product. It supports a 3.1 V to 3.6 V supply, 8 KB packet buffer SRAM, internal DMA, and hardware-assisted checksum calculation according to the Microchip Technology manufacturer data sheet. A smaller controller may be preferable when board area or 10/100 Mb/s performance is the dominant requirement, provided its package and firmware are redesigned.
Is ENC28J60/SP suitable for industrial automation and building automation?
The ENC28J60/SP is suitable for many industrial automation and building automation Ethernet nodes because it integrates a 10BASE-T MAC and PHY, 8 KB packet memory, SPI host access, and internal packet-processing hardware. The verified manufacturer information identifies industrial applications and the related ENC28J60-I/SP carries the industrial temperature-grade ordering option. For equipment exposed to extended temperature conditions, use the -I/SP grade and confirm its exact limits before release.
Where to buy ENC28J60/SP online?
The ENC28J60/SP is listed by DigiKey, Mouser, and Octopart, with product links available in the verified source list. DigiKey lists the related ENC28J60-I/SP configuration as an Ethernet controller with a 10BASE-T PHY, SPI interface, and 28-SPDIP package, while Mouser lists the ENC28J60/SP with 8 KB RAM. Exact stock and transaction price must be confirmed at the distributor because the supplied data contains no verified unit-price or current inventory quantity.
What is the price of ENC28J60/SP?
A verified numeric ENC28J60/SP unit price was not included in the supplied distributor data, so no current market price can be responsibly quoted as of 2026-10-28. Octopart identifies five distributors for price comparison, and DigiKey and Mouser provide direct product listings. The price fields on this page use 0.00 only as a non-orderable quote placeholder; request a current quotation or check the distributor listing before purchasing.
What is the lead time for ENC28J60/SP?
The verified lead time for ENC28J60/SP is not specified, and therefore it remains unknown as of 2026-10-28. DigiKey describes the related ENC28J60-I/SP as available to buy and ship, while Octopart provides distributor availability information, but neither snippet supplies a guaranteed lead time for the exact target MPN. Buyers should request a written lead-time quotation for the selected quantity and confirm whether the manufacturer or an authorized distributor will supply the order.
Is ENC28J60/SP in stock?
Current inventory for the exact ENC28J60/SP is not confirmed by the supplied data as of 2026-10-28. DigiKey shows the related ENC28J60-I/SP as a purchasable listing, and Octopart links several distributors for availability, but those statements do not establish the stock level of ENC28J60/SP. The product offer therefore uses a back-order availability state, and buyers should confirm live stock before releasing a production order.
What crystal does the ENC28J60/SP require?
The ENC28J60/SP is designed for a 25 MHz crystal connected between OSC1 and OSC2. According to the Microchip Technology manufacturer data sheet, the design requires a parallel-resonance crystal rather than a series-resonance crystal because the latter may produce a frequency outside the crystal manufacturer's stated specification. Load capacitance, ESR, startup margin, and PCB placement must therefore be checked against the oscillator requirements in the manufacturer data sheet.
What is the best WIZnet equivalent for ENC28J60/SP?
No verified cross-brand, pin-compatible drop-in equivalent to the ENC28J60/SP was found in the supplied cross-reference data. WIZnet controllers such as the W5500 are often discussed as functional alternatives for embedded Ethernet, but they are not established here as 28-pin DIP, pin-to-pin replacements. Adopting a WIZnet device requires PCB and firmware review; the only source-supported drop-in candidate is the Microchip Technology ENC28J60-I/SP.

داتای سەرچاوەی ئەندازیاری بۆ ENC28J60/SP — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the ENC28J60/SP when a legacy or through-hole embedded design needs a compact, low-cost 10BASE-T Ethernet controller controlled through SPI. Its verified combination of a 3.1 V to 3.6 V supply, integrated MAC and PHY, 8 KB packet RAM, internal DMA, and hardware-assisted checksum calculation supports industrial automation, building automation, home control, security, and VoIP nodes. Choose the ENC28J60-I/SP when the same 28-pin DIP footprint is required but the industrial temperature grade is appropriate. The ENC28J60/SS and ENC28J60/ML are useful when surface-mount area, rather than drop-in compatibility, drives the design. Do not select W5500, DM9051, or ENC424J600 as a direct replacement without accepting a package, pinout, driver, and performance redesign; their 10/100 Mb/s capabilities may be desirable, but they are not verified pin-compatible substitutes for this MPN.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە ENC28J60-I/SP
Brand Microchip Technology Microchip Technology
Package 28-pin DIP 28-pin DIP - same footprint
Integrated Ethernet PHY 10BASE-T 10BASE-T
Host Interface SPI SPI
Supply Voltage Range 3.1 V to 3.6 V 3.1 V to 3.6 V
Packet Buffer SRAM 8 KB 8 KB
Ethernet Standard IEEE 802.3 compatible IEEE 802.3 compatible
DMA Internal DMA module Internal DMA module
Operating Modes Full-duplex and half-duplex Full-duplex and half-duplex
Price Tier Quote required as of 2026-10-28 Quote required as of 2026-10-28

جیاکەرەوە سەرەکییەکان

  • Integrated complete 10BASE-T network interface (بەراورد بەENC28J60-I/SP)
  • Maintains the same verified supply range (بەراورد بەENC28J60-I/SP)
  • Industrial-temperature drop-in sourcing path (بەراورد بەENC28J60-I/SP)
  • Hardware-assisted packet processing (بەراورد بەENC28J60-I/SP)

تێبینییەکانی دیزاین

Place the 25 MHz crystal and load components immediately beside OSC1 and OSC2, and route the oscillator traces away from Ethernet and switching-power traces. The manufacturer data sheet requires a parallel-resonance crystal and warns that a series-resonance crystal may operate outside the crystal manufacturer's specified frequency tolerance. Verify the crystal's load capacitance, ESR, drive level, and startup margin against the oscillator guidance before releasing the PCB.

Connect the ENC28J60/SP through a 10BASE-T magnetic jack and follow the manufacturer layout guidance for the differential Ethernet pairs. Keep the Ethernet interface section compact and isolate it from SPI clocks and noisy power-conversion paths. Because this is a 10BASE-T device with an integrated PHY, the physical-layer layout is part of the Ethernet design rather than an optional connector detail and should be reviewed against the current manufacturer data sheet.

Design the 3.3 V supply path for the verified 3.1 V to 3.6 V operating range and stated 160 mA supply current. Place local bypass capacitance at the controller supply pins and confirm that the upstream regulator has adequate transient margin for Ethernet traffic and startup current. Since no verified unit price, stock quantity, or lead time was supplied, obtain a production quotation rather than relying on the non-orderable pricing placeholder shown on this page.

Do not treat the ENC28J60-I/SP, ENC28J60/SS, or ENC28J60/ML as unqualified alternatives without checking the package. The verified drop-in candidate is ENC28J60-I/SP in the 28-pin DIP package; the /SS and /ML variants use different packages. Likewise, W5500 and DM9051-class devices are functional Ethernet-controller alternatives rather than verified pin-to-pin replacements and require PCB and firmware redesign.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied verified data confirms the IEEE 802.3-compatible Ethernet interface but does not provide product-specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

ENC28J60/SP ENC28J60/SP datasheet PDF Microchip Technology ENC28J60/SP ENC28J60/SP 10BASE-T SPI controller ENC28J60/SP 28-pin DIP ENC28J60/SP industrial automation Ethernet ENC28J60/SP vs ENC28J60-I/SP ENC28J60/SP drop-in replacement ENC28J60/SP buy price ENC28J60/SP stock and lead time ENC28J60/SP pinout ENC28J60/SP 25 MHz crystal requirement 28-pin DIP SPI Ethernet controller ENC28J60 for building automation controller

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology ENC28J60/SP ENC28J60-I/SP ENC28J60/SS ENC28J60/ML ENC28J60 Ethernet controller network interface controller interface IC 10BASE-T PHY media access controller MAC SPI interface IEEE 802.3 internal DMA hardware-assisted checksum calculation 8 KB packet buffer SRAM 25 MHz crystal oscillator parallel-resonance crystal OSC1 OSC2 3.1 V to 3.6 V supply 160 mA supply current 28-pin DIP package industrial automation building automation home control security and surveillance VoIP
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ