KSZ9131RNXI - Gigabit Ethernet Transceiver | Microchip
MPN: KSZ9131RNXI ✓ چالاکKSZ9131RNXI گشتی
A Gigabit Ethernet transceiver, also called an Ethernet PHY, converts between digital MAC-layer data and analog signals carried over twisted-pair cabling. The KSZ9131 belongs to the interface IC hierarchy: Ethernet PHY > physical-layer transceiver > network interface IC > semiconductor. Integrating copper-pair drivers, receivers, clocking, link management, and diagnostics into one device simplifies the hardware around a network processor, gateway, router, or industrial controller.
Key features include automatic selection among 10, 100, and 1000 Mbps speeds and half- or full-duplex operation. Programmable LED outputs report link, activity, and speed status. Wake-on-LAN support uses custom-packet detection, while an energy-detect power-down mode reduces consumption when a cable is not attached. The integrated LinkMD time-domain-reflectance diagnostic helps identify faults in installed copper cabling, and baseline-wander correction supports reliable receive performance.
The KSZ9131 supports GMII, MII, and RGMII host interfaces, giving designers several options for connecting the PHY to an Ethernet MAC. At 1000 Mbps, RGMII uses both edges of a 125 MHz clock for data and control signals, corresponding to an 8 ns clock period as defined by the RGMII 2.0 specification. Differential-pair termination is integrated on chip, reducing the number of external matching components. An external FET and the device's LDO controller support a compact single-3.3 V power architecture.
Typical uses include industrial Ethernet equipment, routers, gateways, switches, embedded network controllers, and other systems requiring 10/100/1000-Mbps copper connectivity. The transceiver can also suit application-specific equipment that needs programmable link and activity indicators, cable diagnostics, reduced standby consumption, or Wake-on-LAN behavior. The combination of IEEE 802.3 operation, automatic negotiation, and multiple MAC-interface options supports both standard and compact network designs.
When designing the PCB, preserve the recommended high-speed copper routing and separation between transmit and receive paths. Follow the manufacturer's pin-description table when assigning power, ground, clock, RGMII, and magnetics-interface signals. Confirm the external-FET configuration and decoupling requirements directly against the manufacturer datasheet before releasing the layout, because incorrect termination or clock topology can affect signal integrity and auto-negotiation.
This product page combines manufacturer specifications, package details, interface capabilities, application guidance, and compatibility-focused alternatives. It also organizes the principal engineering decisions around clocking, power architecture, cable diagnostics, and PCB implementation so that design teams can assess the KSZ9131RNXI before beginning a new Ethernet interface layout.
جێگرەوەکانی جێگۆڕکێ بۆ KSZ9131RNXI — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ KSZ9131RNXI (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Auto-Negotiation, Package, Wake-on-LAN.
KSZ9131RNXC
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →KSZ9131RNXU-VAO
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
KSZ9131RNXI تایبەتمەندییەکان
| Ethernet Data Rate | 10/100/1000 Mbps |
| Duplex Support | Half-duplex and full-duplex |
| Ethernet Compliance | IEEE 802.3 compliant |
| Host Interface | GMII/MII/RGMII |
| I/O Voltage Tolerance | 3.3 V, 2.5 V, and 1.8 V |
| Primary Supply | 3.3 V |
| Reference Clock Output | 125 MHz |
| RGMII Clock Frequency | 125 MHz |
| RGMII Clock Period | 8 ns |
| Differential Pair Termination | On-chip resistors |
| Power Architecture | Single 3.3 V operation with one external FET |
| Auto-Negotiation | 10/100/1000 Mbps and half/full duplex |
| LED Functions | Programmable link, activity, and speed outputs |
| Low-Power Mode | Energy-detect power-down |
| Wake-on-LAN | Supported with custom-packet detection |
| Cable Diagnostic | LinkMD TDR-based diagnostic |
| Baseline Wander | Correction supported |
| پاکێج | 48-QFN (7 x 7 mm) |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی KSZ9131RNXI 48-qfn (7 x 7 mm)
ڕێکخستنی پین بۆ KSZ9131RNXI (پاکێجی 48-qfn (7 x 7 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ KSZ9131RNXI.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
KSZ9131RNXI گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Gateway, Enterprise Router, Managed Network Switch, Embedded Network Controller, Network Storage Appliance, Industrial Control Terminal.
Industrial Ethernet Gateway
The KSZ9131RNXI fits industrial gateways that require a copper Ethernet port with backward compatibility across 10, 100, and 1000 Mbps. Its automatic negotiation selects the highest common link speed and duplex mode, while GMII, MII, and RGMII give the gateway designer several MAC-interface choices. Programmable link, activity, and speed LEDs support enclosure-level diagnostics, and the 48-QFN, 7 x 7 mm package conserves board area. The integrated differential-pair termination and LinkMD cable diagnostic reduce external matching requirements and help commissioning teams isolate field cabling faults.
پێشنیارکراو
Enterprise Router
A router requiring a compact Gigabit Ethernet interface can use the KSZ9131RNXI to provide a 10/100/1000-Mbps copper PHY beside a network processor or switching silicon. RGMII provides a practical option for 1000-Mbps designs, with the manufacturer's datasheet describing both-edge sampling at 125 MHz. The 125 MHz reference-clock output can support system clock distribution. Energy-detect power-down is useful on ports that are present but unused, while programmable status outputs simplify panel indicators for link, traffic, and negotiated speed.
پێشنیارکراو
Managed Network Switch
The KSZ9131RNXI is appropriate for a managed switch line card requiring copper ports with 10/100/1000-Mbps auto-negotiation. Its host-interface selection lets the same PHY family serve designs with different MAC bus architectures, and the small 48-QFN package helps preserve routing area on a multiport board. Integrated differential-pair termination supports cleaner implementation of the analog copper interface. LinkMD diagnostics and programmable LED outputs add serviceability features often required in managed network equipment rather than basic unmanaged switches.
پێشنیارکراو
Embedded Network Controller
An embedded controller or system-on-module can use the KSZ9131RNXI when it needs a deterministic Ethernet physical-layer endpoint close to a high-speed processor. The selectable GMII, MII, and RGMII interfaces allow board architects to balance pin count and throughput against processor I/O availability. Single 3.3 V operation with one external FET simplifies power architecture, while the 125 MHz reference-clock output can assist synchronization. Wake-on-LAN support is beneficial in remotely deployed equipment that must react to designated network packets after an idle period.
پێشنیارکراو
Network Storage Appliance
The KSZ9131RNXI supports network storage appliances that need backward-compatible copper Ethernet connectivity and a compact interface footprint. Automatic negotiation allows the appliance to connect to 10-, 100-, or 1000-Mbps infrastructure without manual speed configuration. The LinkMD diagnostic can help maintenance personnel distinguish cabling faults from storage or server-side problems, reducing troubleshooting time. Wake-on-LAN packet detection also fits appliances that need remote activation, while programmable LEDs can expose link and activity status without dedicating many host GPIO pins.
پێشنیارکراو
Industrial Control Terminal
The KSZ9131RNXI can support an industrial control terminal that connects to a controller or supervisory system over standard copper Ethernet. IEEE 802.3-compliant operation and support for all three speed classes provide compatibility with legacy plant networks and modern gigabit infrastructure. Energy-detect power-down helps reduce consumption when a cable is disconnected, and the small QFN package is useful in compact control panels. Before deployment, confirm the device's temperature grade, isolation architecture, and qualification requirements against the environmental needs of the terminal.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ KSZ9131RNXI — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | KSZ9131RNXC | KSZ9131RNXU-VAO |
|---|---|---|---|
| Package | 48-QFN (7 x 7 mm) | 48-QFN (7 x 7 mm) | 48-QFN (7 x 7 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
جیاکەرەوە سەرەکییەکان
- Broad host-interface selection (بەراورد بەKSZ9131RNXC)
- Integrated copper-interface and power features (بەراورد بەKSZ9131RNXC)
- Field maintenance features (بەراورد بەKSZ9131RNXU-VAO)
تێبینییەکانی دیزاین
Use the manufacturer datasheet as the authority for the 48-QFN land pattern, exposed-pad connection, component placement, and differential-pair routing. Keep the 100BASE-TX/1000BASE-T paths short and symmetrical, and follow the recommended separation between transmit, receive, and digital interface sections. Incorrect layer transitions, unequal pair geometry, or an unsuitable magnetics interface can impair return loss and auto-negotiation even when the schematic is electrically correct.
Implement the single-3.3-V arrangement with the exact external-FET topology and capacitor values specified by Microchip. The on-chip LDO controller is intended to support this architecture, but its performance still depends on correct FET selection, low-impedance supply distribution, and adequate local decoupling. Review absolute maximum ratings, recommended operating conditions, and power-sequence requirements in the manufacturer datasheet before applying either 3.3 V, 2.5 V, or 1.8 V I/O levels.
Treat the 125 MHz reference clock and 1000-Mbps RGMII signals as high-speed digital interfaces. Use the datasheet timing constraints for setup and hold margins, and confirm clock-source jitter and trace-length behavior with the system integrator. RGMII 2.0 uses both edges of the 125 MHz clock for 1000-Mbps data and control signaling, so routing and source-synchronous timing errors can cause intermittent interface failures that do not appear at lower link speeds.
Do not assume that any 48-QFN ordering suffix is automatically interchangeable. Confirm the complete pin description, temperature grade, qualification status, tape-or-tray configuration, and lifecycle conditions for the exact MPN. The KSZ9131RNXC is documented as an equivalent, while suffix-specific conditions for KSZ9131RNXU-VAO require confirmation. Also avoid treating the integrated termination feature as permission to omit the required Ethernet magnetics or protection network.
زانیاری پابەندبوون
No definitive compliance declaration was found in the manufacturer product-page or distributor snippets used for this record.