Microchip Technology

LAN8710A-EZK - 10/100 Ethernet PHY | Microchip Technology

MPN: LAN8710A-EZK ✓ چالاک
2.5 V or 3.3 V variable I/O Vdss 10BASE-T and 100BASE-TX Rds(on) 32-QFN, 5 mm x 5 mm Package 10 Mbps and 100 Mbps Speed
MOQ: 1 |

LAN8710A-EZK گشتی

The Microchip Technology LAN8710A-EZK is a low-power single-channel Ethernet physical-layer transceiver for 10BASE-T and 100BASE-TX links, with support for 10 Mbps and 100 Mbps operation through a variable-voltage digital MII or RMII interface. The device is housed in a 32-QFN package measuring 5 mm by 5 mm. Its feature set includes HP Auto-MDIX, auto-negotiation, flexPWR technology, full-duplex operation, and industrial-temperature options.

An Ethernet PHY, also called an Ethernet physical-layer transceiver, is the interface between a digital Ethernet media-access controller and twisted-pair cabling. It performs signal encoding, line conditioning, auto-negotiation, and crossover handling. The LAN8710A family occupies the physical-layer portion of the Ethernet hierarchy, connecting an Ethernet MAC through MII or RMII while the MAC handles higher-level frame processing.

The LAN8710A-EZK supports both 10BASE-T and 100BASE-TX operation. HP Auto-MDIX allows the PHY to work with straight-through or crossover cables, while auto-negotiation selects the best supported speed and duplex mode. The variable I/O voltage allows the digital interface to operate with either 2.5 V or 3.3 V equipment, depending on the system design and selected operating conditions.

The flexPWR feature is intended to reduce power consumption in portable and space-constrained systems. Microchip describes the LAN8710A family as a small-footprint, low-power solution for consumer electronics, industrial products, and enterprise equipment. Because the PHY is a digital interface IC rather than a power semiconductor, its operating characteristics are primarily defined by link rate, supply voltage, interface mode, temperature range, package, and power-management behavior.

Typical applications include industrial Ethernet equipment, consumer network devices, embedded systems, USB-to-Ethernet adapters, IP cameras, set-top boxes, and communications equipment. The 32-QFN footprint is useful where board area is limited, while MII and RMII support allows the PHY to pair with either a full MII-capable MAC or a reduced pin-count RMII controller.

Designers should confirm the exact supply rails, magnetics, crystal or clock requirements, decoupling, and exposed-pad layout against the manufacturer datasheet. The Ethernet magnetics and line-termination network remain essential parts of the physical design even when the PHY itself is highly integrated. Keep the digital interface traces short and isolate the analog network-side connections from noisy switching nodes.

This page combines the LAN8710A-EZK datasheet, package and interface details, commercially relevant sourcing questions, same-footprint alternatives, comparison points, and practical PCB guidance. It is intended to help engineers evaluate the PHY before integrating it into a new 10/100 Ethernet design.

جێگرەوەکانی جێگۆڕکێ بۆ LAN8710A-EZK — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN8710A-EZK (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, MAC Interface, Cable Support, Channel Count, Power Technology.

Microchip Technology
Package: 32-QFN
MAC Interface: MII and RMII
Cable Support: Direct-connect or crossover LAN cables
بەراوردکردن لەگەڵ LAN8710A-EZK →
Microchip Technology
Package: 32-SQFN, 5 mm x 5 mm
MAC Interface: MII or RMII
بەراوردکردن لەگەڵ LAN8710A-EZK →
Microchip Technology
Package: 32-QFN
MAC Interface: MII and RMII
Cable Support: Direct-connect or crossover LAN cables
بەراوردکردن لەگەڵ LAN8710A-EZK →
Microchip Technology
Package: 32-QFN, 5 x 5 mm
Power Technology: flexPWR technology
بەراوردکردن لەگەڵ LAN8710A-EZK →
Microchip Technology
Package: 32-SQFN, 5x5 mm
MAC Interface: MII or RMII digital interface
Cable Support: 10BASE-T and 100BASE-TX
بەراوردکردن لەگەڵ LAN8710A-EZK →

LAN8710AI-EZK

✅ جێگرەوەی ڕاستەوخۆ
📦 32-QFN (5x5 mm)
Same LAN8710A family and 32-QFN footprint; industrial-temperature ordering option differs from the commercial-range LAN8710A-EZK variant.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LAN8710A-EZC

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 32-QFN (5x5 mm)
10BASE-T and 100BASE-TX · 10 Mbps and 100 Mbps · Full-duplex · MII and RMII · IEEE 802.3u · Supported · HP Auto-MDIX supported · Direct-connect or crossover LAN cables

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN8710A-EZK تایبەتمەندییەکان

Product Type 10/100 Ethernet physical-layer transceiver
Ethernet Speed 10 Mbps and 100 Mbps
Copper Standards 10BASE-T and 100BASE-TX
Host Interface MII and RMII
Compliance IEEE 802.3-2005
Duplex Support Full-duplex
Crossover Handling HP Auto-MDIX
Speed and Duplex Selection Auto-negotiation
Digital I/O Voltage 2.5 V or 3.3 V variable I/O
Power Technology Microchip flexPWR technology
پاکێج 32-QFN, 5 mm x 5 mm
جۆری دامەزراندن Surface mount
Commercial Temperature Range 0°C to 85°C
Industrial Temperature Range -40°C to 85°C
Channel Count 1
Cable Medium Unshielded twisted-pair cable
Maximum Link Rate 100 Mbps

ڕێنمایی ڕێکخستنی پینی LAN8710A-EZK 32-qfn, 5 mm x 5 mm

ڕێکخستنی پین بۆ LAN8710A-EZK (پاکێجی 32-qfn, 5 mm x 5 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 32-qfn, 5 mm x 5 mm بۆ LAN8710A-EZK

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN8710A-EZK.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LAN8710A-EZK گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Control Equipment, ESP32-Based Network Connectivity, IP Camera and Security Equipment, Consumer Network Appliances, USB-to-Ethernet Adapters, Communications and Network Adapters.

🏭

Industrial Ethernet Control Equipment

The LAN8710A-EZK is appropriate for industrial controllers, PLC communication modules, and distributed I/O equipment requiring a compact 10/100 Ethernet endpoint. Its 10BASE-T and 100BASE-TX support covers both legacy 10 Mbps links and faster 100 Mbps industrial traffic, while auto-negotiation selects the supported speed and duplex mode. The MII or RMII interface gives designers flexibility to connect different host controllers. For installations spanning -40°C to 85°C, confirm that the selected ordering code provides the required industrial temperature grade. The 32-QFN footprint also preserves valuable board area, and flexPWR supports designs where energy use and heat generation are important.

🧩

ESP32-Based Network Connectivity

The LAN8710A-EZK can add wired Ethernet connectivity to an ESP32-based product that provides RMII. Its RMII interface reduces host-side pin count compared with MII, while the variable 2.5 V or 3.3 V digital I/O helps align the PHY with the controller interface. The device supports 10 Mbps and 100 Mbps operation, full-duplex transfer, auto-negotiation, and HP Auto-MDIX for flexible cable connection. A practical design still requires exact RMII clock and pin mapping, an appropriate Ethernet transformer, correct termination, and separation between the network side and switching circuitry.

🎥

IP Camera and Security Equipment

The LAN8710A-EZK suits IP cameras, access-control terminals, and other security equipment that requires a compact 10/100 Ethernet physical layer. A 100 Mbps link provides sufficient bandwidth for conventional camera traffic and control traffic while maintaining compatibility with 10 Mbps installations. HP Auto-MDIX removes the need to distinguish straight-through and crossover cables in field installations, and auto-negotiation simplifies interoperability with switches and network equipment. The small 32-QFN package is useful where the camera board must also accommodate sensors, storage, and power conversion. Thermal and EMC performance should be checked for the complete camera enclosure and external cable environment.

📺

Consumer Network Appliances

The LAN8710A-EZK is suitable for set-top boxes, smart-home gateways, printers, and compact consumer network appliances that need 10/100 Ethernet rather than a multi-gigabit PHY. Its low-power design, compact 32-QFN footprint, and flexible MII or RMII host interface allow integration into space- and cost-conscious products. Auto-negotiation enables the device to operate across 10 Mbps and 100 Mbps infrastructure, while HP Auto-MDIX improves installation flexibility with common Ethernet cables. Designers should provide local decoupling, an isolated or filtering network interface through appropriate magnetics, and a layout that separates sensitive clock and I/O signals from high-current power-conversion stages.

💻

USB-to-Ethernet Adapters

The LAN8710A-EZK fits USB-to-Ethernet adapters that require a reliable 10/100 physical layer in a small enclosure. The device provides full-duplex 10BASE-T and 100BASE-TX operation, auto-negotiation, and HP Auto-MDIX while presenting either MII or RMII to the adapter controller. The 32-QFN package limits PCB footprint, helping leave room for the USB interface, magnetics, and connector. A key design concern is keeping USB, Ethernet magnetics, and switching power stages from interfering with each other. Controlled-impedance digital traces, a clean ground reference, and manufacturer-recommended capacitor placement are particularly important in the compact enclosure associated with portable adapters.

🌐

Communications and Network Adapters

The LAN8710A-EZK can support embedded communications equipment, protocol converters, serial-to-Ethernet gateways, and enterprise edge devices requiring a compact 10/100 network port. Its MII and RMII choices permit integration with either a conventional Ethernet MAC interface or a reduced-pin controller. HP Auto-MDIX and auto-negotiation improve compatibility across mixed legacy and fast-Ethernet infrastructure, while flexPWR technology is relevant to systems where idle and active power budgets are constrained. In professional or industrial environments, add isolation only where required by the interface architecture, and verify surge, isolation, and environmental requirements at the system level rather than treating the PHY itself as a complete protection solution.

Where can I download the LAN8710A-EZK datasheet PDF?
The LAN8710A-EZK datasheet PDF is available from Microchip Technology at the official LAN8710A product page and through the manufacturer document link on this page. The document is titled “LAN8710A/LAN8710Ai - Small Footprint MII/RMII 10/100 Ethernet Transceiver.” It covers the LAN8710A and LAN8710Ai families, including MII and RMII host interfaces, 10BASE-T and 100BASE-TX operation, HP Auto-MDIX, auto-negotiation, electrical characteristics, and application guidance.
What are the key specifications of LAN8710A-EZK that engineers should know?
The LAN8710A-EZK is a single-channel 10/100 Ethernet PHY supporting 10BASE-T and 100BASE-TX at 10 Mbps and 100 Mbps. It connects to an Ethernet MAC through variable-voltage MII or RMII, supports full-duplex operation, HP Auto-MDIX, and auto-negotiation, and uses Microchip flexPWR technology. The package is a 32-QFN measuring 5 mm by 5 mm, making it suitable for compact embedded, industrial, consumer, and communications equipment.
Where can I find the LAN8710A-EZK pinout and package drawing?
The LAN8710A-EZK pinout, package drawing, and recommended land pattern are in the pin-description and package-information sections of the manufacturer LAN8710A/LAN8710Ai datasheet. The target is a 32-QFN package with an exposed thermal pad, so PCB design should follow the manufacturer’s land pattern and exposed-pad guidance. Use the datasheet for exact ball assignments, exposed-pad connection, and soldering requirements rather than inferring positions from a generic QFN drawing.
Is LAN8710A-EZK suitable for industrial Ethernet equipment?
The LAN8710A-EZK is suitable for industrial Ethernet designs that require 10BASE-T or 100BASE-TX connectivity and can be implemented within the device’s specified electrical and temperature limits. The LAN8710A family includes industrial-temperature options from -40°C to 85°C, although the exact temperature range for a specific ordering code must be checked in the manufacturer ordering information. The device also supports HP Auto-MDIX, full-duplex operation, and auto-negotiation.
Can LAN8710A-EZK work with an RMII Ethernet MAC?
Yes. The LAN8710A-EZK supports both MII and RMII host interfaces, allowing it to operate with a reduced-pin-count RMII media-access controller as well as a full MII controller. According to the Microchip LAN8710A/LAN8710Ai datasheet, the digital interface uses variable I/O voltage for 2.5 V or 3.3 V equipment. The host MAC, clocking method, interrupt behavior, and selected supply configuration must still be matched in the system design.
What is the difference between LAN8710A-EZK and LAN8710AI-EZK?
LAN8710AI-EZK is the industrial-temperature member of the same LAN8710A family and is listed by Microchip as a compatible alternative. The family datasheet covers both LAN8710A and LAN8710Ai devices, while Microchip’s product page identifies extended commercial and industrial temperature options. The most important selection check is the exact ordering-code temperature grade and required qualification, not merely the Ethernet speed or package name.
Can LAN8710AI-EZK replace LAN8710A-EZK without changing the PCB?
LAN8710AI-EZK is a same-family, same-package replacement candidate for LAN8710A-EZK. Cross-reference listings identify the two 32-pin QFN parts as compatible, and both belong to the LAN8710A/LAN8710Ai family covered by one datasheet. Before substitution, confirm the required temperature grade, ordering suffix, clock and strap configuration, and exposed-pad implementation. Similarity in MPN naming alone is not a substitute for reviewing the manufacturer pin and ordering tables.
What is the best drop-in replacement for LAN8710A-EZK?
LAN8710AI-EZK is the best-supported drop-in replacement candidate because it belongs to the same Microchip LAN8710A family, uses the same 32-QFN footprint, and is explicitly listed as compatible in cross-reference results. LAN8710A-EZC is another same-family candidate that should be checked for ordering-code and temperature differences. Only LAN8710AI-EZK and LAN8710A-EZC have sufficiently supported package and family information in the available cross-reference records; other PHY families are not asserted as drop-in replacements.
What can replace LAN8710A-EZK?
LAN8710AI-EZK can replace LAN8710A-EZK when the system requirements match the industrial-temperature ordering code and the manufacturer’s pin configuration. LAN8710A-EZC is a second same-family replacement candidate. A valid replacement must preserve the 32-QFN footprint, MII or RMII host-interface arrangement, supply strategy, clocking method, and Ethernet physical-layer requirements. Parts with different packages or undocumented pin assignments should not be treated as drop-in replacements.
Is LAN8710A-EZK the same as LAN8710A-EZC?
LAN8710A-EZK and LAN8710A-EZC are closely related LAN8710A family devices, but they are distinct ordering codes. Cross-reference data lists LAN8710A-EZC as a compatible alternative to LAN8710A-EZK, and both are associated with the same 32-QFN family and MII/RMII 10/100 Ethernet feature set. The ordering-code table and temperature-grade designation should be reviewed to determine whether a particular sourcing substitution is acceptable.
When should I choose LAN8710A-EZK over LAN8710AI-EZK?
Choose LAN8710A-EZK when the required product ordering code corresponds to the application’s commercial temperature range and the board does not need the industrial-temperature option. Choose LAN8710AI-EZK for a design specified for -40°C to 85°C operation, provided the industrial ordering code is required by the system. Both use the same 32-QFN package and provide 10/100 Ethernet, MII/RMII, HP Auto-MDIX, auto-negotiation, and flexPWR functionality.
Is LAN8710A-EZK suitable for an ESP32-based Ethernet design?
The LAN8710A-EZK can fit an ESP32-based Ethernet design when the selected ESP32 device includes an appropriate RMII interface and the board supplies the required PHY clocks, references, magnetics, and power rails. Its RMII interface and variable 2.5 V or 3.3 V digital I/O help integrate it with compact embedded systems. Because ESP32 variants and pin multiplexing differ, verify the exact MCU, RMII timing, interrupt pins, and PHY address configuration before release.
What power and thermal considerations apply to LAN8710A-EZK?
LAN8710A-EZK is a low-power Ethernet PHY, but its total board dissipation depends on the selected core supply, digital I/O rail, operating speed, cable link state, and surrounding circuitry. The 32-QFN exposed pad provides the primary thermal path on the PCB and must be connected according to the manufacturer land pattern. Use the datasheet current tables for the exact operating condition, and calculate worst-case local heating from actual supply currents rather than assuming the entire PHY load must be handled through a narrow thermal path.
How do I design the PCB around a LAN8710A-EZK Ethernet PHY?
Place the PHY close to the Ethernet transformer and RJ45 connector, keep the network-side traces short and controlled, and route digital MII or RMII signals away from switching power nodes. Follow the manufacturer recommended decoupling, crystal or clock layout, exposed-pad, and copper-pour requirements. Provide a low-impedance ground return for the digital interface and isolate the line-side magnetics from sensitive circuitry. The reference schematic and layout guidance in the LAN8710A datasheet should be the basis of the production layout.
Where can I buy LAN8710A-EZK and what is its current lead time?
Use the Request a Quote form on this page to ask about LAN8710A-EZK availability, current lead time, minimum order quantity, and shipment quantity. Current quote-based inventory and lead time can change independently of the product specification, so request an updated response for the exact MPN and required quantity. The 32-QFN package and ordering code shown here should be stated on the request so that the quote corresponds to the intended device variant.
What is the price of LAN8710A-EZK?
The current commercial price for LAN8710A-EZK depends on order quantity, supply status, and the requested shipment form. Submit the exact MPN and quantity through the Request a Quote form on this page for a current offer. The product page does not embed a static price because such figures become stale and may differ from the quantity and fulfillment terms selected during quotation.
Is LAN8710A-EZK in stock?
Current stock for LAN8710A-EZK should be confirmed through the Request a Quote form on this page. Enter the exact MPN, required quantity, and preferred shipment date so the response reflects the latest available inventory. Because this product uses a specific ordering code and 32-QFN package, confirm that the quoted material matches LAN8710A-EZK rather than a related LAN8710A family variant.

داتای سەرچاوەی ئەندازیاری بۆ LAN8710A-EZK — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose LAN8710A-EZK when its exact ordering code satisfies the required commercial temperature range and the system needs a compact, low-power 10/100 Ethernet PHY with MII or RMII, HP Auto-MDIX, and auto-negotiation. Choose LAN8710AI-EZK when the design requires the -40°C to 85°C industrial option; it retains the same 32-QFN footprint and core LAN8710A functionality. Choose LAN8710A-EZC when that specific ordering code is the required source configuration, after verifying its temperature and suffix differences against the manufacturer ordering table. For designs requiring gigabit Ethernet, neither listed alternative is a drop-in replacement; use a gigabit PHY and perform the corresponding PCB redesign. Always verify clocking, straps, supplies, magnetics, and exposed-pad layout before substitution.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LAN8710AI-EZK LAN8710A-EZC
Brand Microchip Technology Microchip Technology Microchip Technology
Package 32-QFN (5x5 mm) 32-QFN (5x5 mm) - same 32-QFN (5x5 mm) - same
Ethernet Speed 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps
Copper Standards 10BASE-T and 100BASE-TX 10BASE-T and 100BASE-TX 10BASE-T and 100BASE-TX
Host Interface MII and RMII MII and RMII MII and RMII
Auto-MDIX HP Auto-MDIX HP Auto-MDIX HP Auto-MDIX
Auto-Negotiation Supported Supported Supported
Power Technology Microchip flexPWR technology Microchip flexPWR technology Microchip flexPWR technology

جیاکەرەوە سەرەکییەکان

  • Compact 32-QFN implementation with complete 10/100 Ethernet PHY functionality (بەراورد بەLAN8710A-EZC)
  • MII and RMII support with variable digital I/O voltage (بەراورد بەLAN8710AI-EZK)
  • HP Auto-MDIX and auto-negotiation simplify field interoperability (بەراورد بەLAN8710A-EZC)

تێبینییەکانی دیزاین

Place the LAN8710A-EZK, its crystal or clock components, and decoupling capacitors close to the associated pins. Follow the manufacturer datasheet layout for the 32-QFN exposed pad and provide a low-impedance connection to the ground plane. Keep the MII or RMII traces short and controlled, and route them away from the line-side transformer connections and switching-regulator power nodes.

Design the Ethernet network side as a controlled, quiet interface between the PHY and the isolation transformer. Avoid routing network-side traces beneath noisy digital or power-conversion areas, and use a continuous ground reference under the PHY. Magnetic-component placement and the exact line-side component arrangement should follow the manufacturer reference schematic, because connector and magnetics geometry can materially affect electromagnetic performance.

Do not treat a related LAN8710A ordering code as interchangeable without checking the pin table, temperature grade, clocking configuration, strap settings, and exposed-pad layout. LAN8710AI-EZK and LAN8710A-EZC are the supported same-family candidates here, but their ordering suffixes still require review. Also confirm the host MAC uses the same RMII clock convention and reference configuration before a board is released to production.

Use separate filtering or local decoupling for the PHY core and digital I/O rails according to the manufacturer recommendations. Estimate the board-level dissipation from the actual core voltage, I/O voltage, link state, and measured or datasheet current for the selected mode. The exposed pad is a thermal and electrical connection, so a small isolated pad area or an improperly separated ground split can increase voltage drop and temperature rise.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The family datasheet identifies compliance with IEEE 802.3-2005. No separate RoHS, REACH, automotive, lead-free, halogen-free, or conflict-minerals declaration was established for this exact ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lan8710a datasheet lan8710a ezc lan8710a ezc tr lan8710a ezc abc lan8710a ezc qfn32 lan8710a ezc datasheet lan8710a reference schematic lan8710a esp32 lan8710a ezc tr abc LAN8710A-EZK datasheet LAN8710A-EZK pinout LAN8710A-EZK replacement LAN8710A-EZK equivalent LAN8710A-EZK price LAN8710A-EZK RMII interface

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology LAN8710A-EZK LAN8710AI-EZK LAN8710A-EZC Ethernet PHY physical-layer transceiver 10BASE-T 100BASE-TX 10 Mbps 100 Mbps MII RMII IEEE 802.3-2005 HP Auto-MDIX flexPWR technology 32-QFN QFN family surface-mount package unshielded twisted-pair cable Ethernet MAC auto-negotiation variable I/O voltage industrial Ethernet ESP32
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ