Microchip Technology

LAN91C111-NE - 10/100 Ethernet MAC + PHY | Microchip

MPN: LAN91C111-NE ✓ چالاک
10 Mbps and 100 Mbps Speed 8 KB dynamically configurable TX/RX Memory
MOQ: 1 |

LAN91C111-NE گشتی

The Microchip LAN91C111-NE is a single-chip 10/100 Ethernet controller integrating a Media Access Control layer and Physical Layer in a mixed-signal Analog/Digital device. It supports 10 Mbps and 100 Mbps operation, configurable 32-bit, 16-bit, or 8-bit host interfaces, full-duplex switched Ethernet, and 8 KB of dynamically configurable transmit and receive FIFO memory. The device uses an IEEE 802.3-compatible Ethernet architecture for embedded systems.

An Ethernet MAC and PHY combined on one IC form the interface between an embedded host processor and a physical copper network. The MAC manages frame processing, addressing, collision handling, and data movement, while the PHY converts logical data into signals that can be transmitted over twisted-pair Ethernet. Integrating both functions reduces external component count and simplifies PCB routing compared with a separated MAC and transceiver design.

The LAN91C111 family provides dual-speed 10/100 Mbps connectivity, AutoNegotiation, burst data transfer, and selectable host-bus widths. Its 8 KB internal FIFO buffer separates host processing from Ethernet timing, helping manage burst traffic on embedded processor buses. The flexible 8-, 16-, or 32-bit host interface allows the same controller architecture to address systems with different data-bus capabilities.

The controller implements the MAC and PHY portions of the CSMA/CD protocol. Its receive path aligns scrambled data to IEEE 802.3 5B word boundaries, descrambles the recovered data, and transfers it to the 4B/5B decoder. On the transmit side, the integrated Ethernet engine prepares frames for the physical layer while the internal FIFOs buffer host and network traffic. This architecture supports both 10 Mbps and 100 Mbps links without requiring a separate Ethernet interface controller.

Typical uses include embedded industrial controllers, factory automation equipment, embedded Web servers, set-top boxes, print systems, and network-connected embedded products. It is particularly useful where a host processor needs compact 10/100 Ethernet connectivity without a PCI bus or a separate physical-layer transceiver. The selectable host width also helps optimize external bus wiring and processor interface overhead.

PCB design should preserve short, controlled impedance Ethernet traces and provide the external magnetic-interface components required by the application circuitry. Place the controller and supporting clock, decoupling, and interface components according to the manufacturer datasheet layout. Check the host-bus voltage, reset requirements, interrupt connections, and FIFO configuration in firmware before finalizing the system interface.

This page combines the manufacturer architecture description with practical interface guidance, verified MPN comparison points, and implementation-oriented design notes. It is structured to help engineers identify the correct LAN91C111 ordering variant, plan the host interface, and evaluate the controller for compact embedded Ethernet designs.

جێگرەوەکانی جێگۆڕکێ بۆ LAN91C111-NE — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN91C111-NE (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Internal FIFO Memory, Network Standard.

Microchip Technology
Internal FIFO Memory: 8 KB dynamically configurable TX/RX SRAM
Network Standard: 10/100 Base-T/TX
بەراوردکردن لەگەڵ LAN91C111-NE →

LAN91C111I-NU

✅ جێگرەوەی ڕاستەوخۆ
📦 TQFP-128 (14 x 14 mm)
Core ratings remain 10/100 Mbps with an 8 KB FIFO and 8/16/32-bit host bus; the I-NU ordering option changes the qualification or temperature configuration and must be confirmed against the target ordering code

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LAN91C111I-NS

✅ جێگرەوەی ڕاستەوخۆ
📦 TQFP-128 (14 x 14 mm)
Core ratings remain 10/100 Mbps with an 8 KB FIFO and 8/16/32-bit host bus; the suffix changes ordering, qualification, or packaging details, with 0% change to the stated speed and memory ratings

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LAN91C111-NU

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 TQFP-128 (14 x 14 mm)
10/100 non-PCI Ethernet single-chip MAC and PHY · 10 Mbps and 100 Mbps · 8-bit, 16-bit, or 32-bit parallel bus · 8 KB dynamically configurable TX/RX SRAM · 10/100 Base-T/TX · CSMA/CD · 3.3 V · 128-lead TQFP, 14 mm x 14 mm

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN91C111-NE تایبەتمەندییەکان

Product Type 10/100 Ethernet single-chip MAC and PHY
Ethernet Speed 10 Mbps and 100 Mbps
Host Interface Width 8-bit, 16-bit, or 32-bit
Integrated Functions Ethernet MAC and Ethernet PHY
Internal FIFO Memory 8 KB dynamically configurable TX/RX
Duplex Support Full duplex
Network Standard IEEE 802.3
Media Access Method CSMA/CD
AutoNegotiation Supported
Data Transfer Burst data transfer
Device Architecture Mixed-signal Analog/Digital
Host Bus Type Non-PCI parallel host interface

ڕێنمایی ڕێکخستنی پینی LAN91C111-NE standard

ڕێکخستنی پین بۆ LAN91C111-NE (پاکێجی standard). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی standard بۆ LAN91C111-NE

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN91C111-NE.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LAN91C111-NE گونجاوە بۆ 6 بەکارھێنانs: Embedded Industrial Automation Controller, Embedded Web Server, Factory Data Acquisition Terminal, Network-Connected Printer Controller, Set-Top Box Network Port, IoT Gateway with Legacy Host Interface.

🏭

Embedded Industrial Automation Controller

The LAN91C111-NE is appropriate for an embedded automation controller that must exchange real-time status and command data over a 10/100 Ethernet network. Its selectable 8-bit, 16-bit, or 32-bit host bus lets the design match the controller processor while minimizing unnecessary external signals, and the 8 KB dynamically configurable FIFO separates burst traffic from host processing. AutoNegotiation allows the controller to operate with 10 Mbps or 100 Mbps network equipment. For factory equipment, verify the exact ordering variant's temperature and lifecycle status, then isolate Ethernet transients and route controlled-impedance traces according to the manufacturer layout guidance.

🌐

Embedded Web Server

The LAN91C111-NE can provide the physical Ethernet connection for a compact embedded Web server running on an 8-bit, 16-bit, or 32-bit host processor. At 10 Mbps and 100 Mbps, the controller supports conventional Fast Ethernet networks, while AutoNegotiation selects the link rate and full-duplex operation. The 8 KB transmit and receive FIFO helps the server handle request bursts without requiring a PCI bus. Firmware should configure the selected host width, interrupt behavior, receive buffer boundaries, and address filtering before the server exposes its network interface.

📊

Factory Data Acquisition Terminal

The LAN91C111-NE is well suited to a factory data-acquisition terminal that sends sensor records and receives configuration commands over Fast Ethernet. Its 8 KB dynamically configurable TX/RX FIFO supports burst data transfer, while the adjustable host-bus width can accommodate processors with different external data-bus capabilities. The integrated MAC and PHY reduces the component count compared with separate Ethernet implementations. To preserve data integrity, synchronize packet handling with the appropriate interrupts, size software buffers for the expected traffic pattern, and keep copper-interface routing away from high-energy switching nodes.

🖨️

Network-Connected Printer Controller

The LAN91C111-NE offers a compact interface for a printer controller that needs 10/100 Ethernet without a separate PCI network card. The controller handles the Ethernet MAC and PHY functions at 10 Mbps and 100 Mbps and provides a selectable parallel host interface for the embedded print engine processor. Its 8 KB FIFO supports burst-oriented traffic associated with print jobs and management packets. The implementation should reserve suitable RAM for protocol buffers, manage flow control carefully during large transfers, and validate the host timing, reset sequence, and interrupt setup against the manufacturer datasheet.

📺

Set-Top Box Network Port

The LAN91C111-NE can serve as the 10/100 Ethernet connection for a set-top box or similar multimedia terminal. AutoNegotiation and full-duplex support allow the device to connect across common Fast Ethernet infrastructure, while the 8 KB FIFO handles burst transfers generated by streaming services, control messages, and software updates. The selectable 8-, 16-, or 32-bit host interface offers flexibility when integrating with the main processor. Software should maintain consistent FIFO allocation under sustained traffic and use the interrupt scheme that best matches the platform's real-time requirements.

🧩

IoT Gateway with Legacy Host Interface

The LAN91C111-NE is appropriate for an IoT gateway that connects an embedded supervisory processor to a Fast Ethernet backbone. The 8-bit host mode can reduce interface wiring when throughput requirements are modest, while 16-bit and 32-bit modes provide greater bandwidth for aggregation and uplink traffic. Its integrated MAC and PHY, AutoNegotiation, and 8 KB FIFO support a compact gateway implementation. The gateway firmware should separate real-time Ethernet servicing from application tasks, monitor buffer occupancy under traffic bursts, and confirm the selected package and suffix before release to production.

کورتەی بەرهەمە پێشنیارکراوەکان

LAN91C111I-NU Industrial-oriented family variant for Ethernet controller designs بەکارهێنراوە لە: Embedded Industrial Automation Controller, Embedded Web Server, Factory Data Acquisition Terminal, Network-Connected Printer Controller, Set-Top Box Network Port, IoT Gateway with Legacy Host Interface LAN91C111I-NS Alternative family ordering option for embedded Ethernet interfaces بەکارهێنراوە لە: Embedded Industrial Automation Controller, Factory Data Acquisition Terminal, Set-Top Box Network Port LAN91C111-NU Microchip Technology بەکارهێنراوە لە: Embedded Web Server, Network-Connected Printer Controller, IoT Gateway with Legacy Host Interface
What is the LAN91C111-NE and what does it integrate?
The LAN91C111-NE is a single-chip 10/100 Ethernet controller that integrates a Media Access Control layer and a Physical Layer. According to the Microchip LAN91C111 datasheet, it is a mixed-signal Analog/Digital device implementing the MAC and PHY portions of the CSMA/CD protocol at 10 Mbps and 100 Mbps. The integrated design reduces the number of external Ethernet interface devices required around an embedded host processor.
What host interface widths does the LAN91C111 support?
The LAN91C111 supports 8-bit, 16-bit, and 32-bit parallel host interfaces. According to the Microchip LAN91C111 product page and datasheet, this configurable bus width helps minimize data-throughput constraints in embedded applications. Firmware and board routing must be configured for the selected width, so the host processor data lines and control signals should be assigned consistently before PCB layout.
How much FIFO memory is built into the LAN91C111-NE?
The LAN91C111-NE contains 8 KB of dynamically configurable transmit and receive FIFO SRAM. According to the manufacturer application note on the 32/16/8-bit Fast Ethernet controller, the FIFO decouples host-side activity from Ethernet packet timing. This buffering supports burst transfers and can reduce the frequency at which the embedded host must service individual Ethernet data transfers.
Does the LAN91C111-NE support both 10 Mbps and 100 Mbps Ethernet?
Yes, the LAN91C111-NE supports dual-speed operation at 10 Mbps and 100 Mbps. According to the Microchip LAN91C111 datasheet, the controller also includes AutoNegotiation and supports full-duplex switched Ethernet. The operating rate is negotiated with the connected network equipment, while the system remains based on the same integrated MAC, PHY, and internal FIFO architecture.
Where can I download the LAN91C111-NE datasheet PDF?
The official LAN91C111 datasheet PDF is available from Microchip Technology at the manufacturer document link listed on this page. According to Microchip, the document covers the 10/100 Non-PCI Ethernet single-chip MAC and PHY, including the 8-, 16-, and 32-bit host interfaces, internal FIFOs, AutoNegotiation, electrical characteristics, and register information. Use that document for the definitive pin descriptions and layout requirements.
Where can I find the LAN91C111-NE pinout and package details?
The LAN91C111-NE pinout and package drawing are in the pin-description and package sections of the official Microchip LAN91C111 datasheet. The exact package designation is not stated in the product listing excerpts used for this page, so use the ordering-information section to confirm the mechanical drawing and pin numbering. Do not assign PCB lands from the LAN91C111I-NU package unless the ordering suffix has been positively matched.
Is the LAN91C111-NE suitable for industrial embedded Ethernet?
The LAN91C111-NE is architecturally suitable for embedded Ethernet systems that need a compact non-PCI 10/100 interface. According to the Microchip datasheet, it supports selectable host-bus widths, AutoNegotiation, full-duplex operation, and 8 KB of internal FIFO memory. For an industrial deployment, confirm the ordering variant's temperature rating and current lifecycle status, then apply the environmental requirements of the finished equipment.
What is the difference between LAN91C111-NE and LAN91C111I-NU?
The LAN91C111-NE and LAN91C111I-NU belong to the same LAN91C111 controller family and share the core 10/100 Ethernet MAC, PHY, AutoNegotiation, and FIFO architecture. The ordering suffixes distinguish qualification, temperature, or packaging options. According to the manufacturer naming and comparison records, LAN91C111I-NU is a 128-TQFP variant; verify the complete suffix, temperature grade, and package against the Microchip ordering table before treating it as a drop-in substitution.
Can LAN91C111I-NU replace LAN91C111-NE on an existing PCB?
LAN91C111I-NU can be considered for replacement only after its package, pinout, temperature grade, and ordering options have been matched to the installed LAN91C111-NE. The comparison data identifies LAN91C111I-NU as a 128-TQFP Ethernet controller, but it does not establish complete pin-for-pin equivalence with the target suffix. Review the Microchip datasheet and ordering table, then confirm reset, clock, interrupt, and host-bus behavior before approving the substitution.
What is the best drop-in replacement for LAN91C111-NE?
No fully verified cross-manufacturer drop-in replacement for LAN91C111-NE was identified in the available comparison records. The closest documented family candidates are LAN91C111I-NU and LAN91C111I-NS, but suffix-level package, temperature, and qualification differences must be resolved against the manufacturer ordering information. Use the Request a Quote form on this page for availability and sourcing support, and avoid treating a similar Ethernet controller as drop-in without footprint and pin-level verification.
When should I choose the LAN91C111 over a separate Ethernet MAC and PHY?
Choose the LAN91C111 when an embedded system needs 10/100 Ethernet without a PCI interface or a separate physical-layer transceiver. According to the Microchip application note, the device combines a MAC, PHY, and 8 KB dynamically configurable FIFO SRAM in one package. The trade-off is reduced design flexibility: applications needing multiple PHY interfaces, advanced media-access features, or a different host protocol should compare the integrated LAN91C111 against modular Ethernet solutions.
Is the LAN91C111-NE suitable for an embedded Web server?
Yes, the LAN91C111-NE fits embedded Web-server designs requiring a compact 10/100 Ethernet endpoint. Its 10 Mbps and 100 Mbps modes, AutoNegotiation, full-duplex operation, and 8 KB transmit/receive FIFO buffer suit burst-oriented embedded traffic. According to the Microchip datasheet, the 8-, 16-, or 32-bit host interface can also be matched to the processor bus, reducing unnecessary wiring on hosts with limited external I/O.
How do I choose between 8-bit, 16-bit, and 32-bit LAN91C111 host modes?
Select the host width that best matches the processor bus, data throughput, PCB routing, and firmware driver. According to the Microchip LAN91C111 application note, the controller supports 32/16/8-bit operation, and wider modes can transfer more data per host cycle while narrower modes may reduce pin count and routing complexity. The operating mode must agree with the physical bus connections and software register configuration.
What is the role of the LAN91C111 internal FIFO in burst transfers?
The 8 KB internal FIFO stores Ethernet data between the network interface and host interface, reducing direct coupling between packet timing and processor access. According to the manufacturer application note, the TX/RX memory is dynamically configurable. This lets a burst transfer continue through a controlled FIFO rather than requiring every byte to be serviced synchronously by the host, although software must still configure buffer boundaries and maintain suitable interrupt handling.
Where can I buy LAN91C111-NE and what is its lead time?
Use the Request a Quote form on this page for the LAN91C111-NE, current price, stock position, minimum order quantity, and production lead time. The available distributor listings confirm the exact MPN, but they do not print explicit quantity-break prices that can be reproduced reliably. Lifecycle, temperature grade, and package should also be confirmed during quotation because suffix variants may differ in qualification and shipment conditions.

داتای سەرچاوەی ئەندازیاری بۆ LAN91C111-NE — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LAN91C111-NE for a compact embedded system that needs a non-PCI 10/100 Ethernet endpoint with a selectable 8-, 16-, or 32-bit host bus. Its integrated MAC, PHY, AutoNegotiation, full-duplex support, and 8 KB FIFO provide a practical single-chip network interface. Consider LAN91C111I-NU when an industrial-oriented ordering option and documented 128-TQFP package match the design requirements, but confirm temperature and qualification details. LAN91C111I-NS or LAN91C111-NU may fit other ordering or lifecycle requirements within the same family, provided the package, temperature grade, and suffix meaning are checked. Do not approve a cross-manufacturer substitute solely from Ethernet-speed similarity; require a documented pin-for-pin footprint and compatible host, reset, clock, interrupt, and PHY implementation.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LAN91C111I-NU LAN91C111I-NS LAN91C111-NU
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package TQFP-128 (14 x 14 mm) TQFP-128 (14 x 14 mm) TQFP-128 (14 x 14 mm) TQFP-128 (14 x 14 mm)
Ethernet Speed 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps 10 Mbps and 100 Mbps
Integrated Functions MAC and PHY MAC and PHY MAC and PHY MAC and PHY
Host Interface Width 8-bit, 16-bit, or 32-bit 8-bit, 16-bit, or 32-bit 8-bit, 16-bit, or 32-bit 8-bit, 16-bit, or 32-bit
Internal FIFO Memory 8 KB 8 KB 8 KB 8 KB
AutoNegotiation Supported Supported Supported Supported
Duplex Mode Full duplex Full duplex Full duplex Full duplex
Host Bus Type Non-PCI parallel interface Non-PCI parallel interface Non-PCI parallel interface Non-PCI parallel interface
Ordering Qualification Commercial LAN91C111-NE ordering option I-NU ordering option I-NS ordering option NU ordering option

جیاکەرەوە سەرەکییەکان

  • Combines the Ethernet MAC and PHY in one controller (بەراورد بەLAN91C111I-NU)
  • Supports three parallel host-bus widths (بەراورد بەLAN91C111I-NS)
  • Provides 8 KB of dynamically configurable FIFO memory (بەراورد بەLAN91C111-NU)

تێبینییەکانی دیزاین

Use the manufacturer pin-description table and layout example before assigning Ethernet or host-bus lands. The LAN91C111 combines mixed-signal PHY circuitry with a high-speed parallel host interface, so keep the clock and data routes short, route the host bus consistently, and place required bypass capacitors close to their specified pins. Do not derive the target footprint solely from a family member: verify that the exact -NE ordering code uses the same mechanical drawing and pin numbering.

Plan the copper interface section as a controlled-impedance Ethernet region and keep it isolated from noisy switching circuitry. Follow the reference layout in the official LAN91C111 datasheet for the PHY, magnetic-interface components, clock source, and grounding arrangement. The 8-, 16-, and 32-bit host width changes signal count and routing pressure, so choose the narrowest mode that satisfies host throughput and packet-service latency requirements.

Configure software and hardware consistently for host width, buffer allocation, address filtering, reset, interrupts, and AutoNegotiation before diagnosing a network failure. The controller supports 10 Mbps and 100 Mbps and full-duplex switched Ethernet, but incorrect FIFO management or interrupt assumptions can still reduce effective throughput. When comparing ordering suffixes, confirm package, temperature grade, qualification, and lifecycle status rather than treating the I, N, E, or S characters as interchangeable packaging details.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status was not explicitly identified in the manufacturer or distributor product information used for this page. The industrial or automotive classification of the I-series ordering option should not be inferred from the suffix alone; confirm the official ordering information for the exact MPN.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lan91c111 datasheet lan91c111 nu datasheet lan91c111 ns datasheet smsc lan91c111 LAN91C111-NE datasheet pdf LAN91C111-NE pinout LAN91C111-NE equivalent LAN91C111-NE replacement LAN91C111-NE vs LAN91C111I-NU LAN91C111-NE price LAN91C111-NE 10/100 Ethernet controller LAN91C111-NE TQFP-128 footprint

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology SMSC LAN91C111-NE LAN91C111I-NU LAN91C111I-NS LAN91C111-NU Ethernet controller Ethernet MAC Ethernet PHY 10/100 Ethernet Fast Ethernet CSMA/CD IEEE 802.3 AutoNegotiation non-PCI parallel host interface 8 KB FIFO dynamically configurable TX/RX FIFO mixed-signal Analog/Digital device TQFP-128 surface-mount package embedded systems industrial automation embedded Web server IoT gateway full-duplex switched Ethernet
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ