Microchip Technology

LAN9215I-MT - 10/100 Ethernet Controller | Microchip

MPN: LAN9215I-MT ✓ چالاک
1.8 V Vdss 49.9 Ω pull-up on TPO+ Rds(on) 100-pin TQFP, 14 x 14 mm Package 10 Mb/s or 100 Mb/s Speed
MOQ: 1 |

LAN9215I-MT گشتی

The Microchip Technology LAN9215I-MT is a single-chip 10/100 Ethernet controller with an integrated 10/100 Base-T/TX PHY, a 16-bit MII interface, and a 100-pin TQFP package measuring 14 x 14 mm. It is designed for embedded systems that require Ethernet connectivity while controlling system cost and CPU overhead. The verified distributor listing identifies the device as a 10/100 Base-T/TX Ethernet controller with a parallel interface, while the manufacturer describes the LAN9215 family as a full-featured solution for embedded applications.

An Ethernet controller is an interface integrated circuit that connects an embedded processor or programmable logic device to an Ethernet physical layer. In this case, the hierarchy is Ethernet controller > network interface controller > interface IC > semiconductor. Combining the controller and PHY reduces external component count, but the LAN9215I-MT still requires an Ethernet magnetics and connector implementation as well as a suitable 16-bit host bus connection.

Verified features include a 16-bit MII interface, HP Auto-MDIX support, interrupt generation, 3.3 V operation with wake-up functionality, non-volatile configuration storage, and power-up or reset configuration. These capabilities suit designs requiring controlled Ethernet startup, host interrupt handling, and flexible configuration retention. The controller architecture is described as efficient, with low CPU overhead for medium-performance embedded applications.

The LAN9215I-MT supports 10/100 Mb/s Ethernet connectivity, allowing equipment to participate in 10 Mb/s or 100 Mb/s networks. Its integrated controller and PHY simplify the signal chain compared with a discrete Ethernet MAC and separate PHY. The parallel MII interface remains important for embedded processors that do not include an integrated Ethernet MAC and need a conventional external data bus rather than a serial peripheral interface.

Typical uses include industrial control equipment, factory automation controllers, embedded gateways, instrumentation, and network-enabled data acquisition systems. In these applications, the MII interface can connect to a host processor, the Auto-MDIX function can simplify straight-through or crossover cable handling, and configuration storage can reduce firmware initialization work. Wake-up and interrupt support also benefit systems that need controlled network activity and event-driven host processing.

Designers should follow the manufacturer's TQFP placement checklist, particularly the 49.9 ohm TX termination pull-up arrangement specified for TPO+ when Auto-MDIX is enabled. Confirm the complete package pin assignment, power rails, decoupling requirements, magnetics selection, reference schematic, and PCB constraints against the manufacturer datasheet before releasing a layout.

This page consolidates verified manufacturer and distributor information, transparent data gaps, drop-in replacement evidence, and application-focused design guidance. It distinguishes confirmed electrical and packaging facts from unverified details that still require validation against the official LAN9215I documentation.

جێگرەوەکانی جێگۆڕکێ بۆ LAN9215I-MT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9215I-MT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Host Interface, Package, Auto-MDIX, Device Type, Ethernet Speed.

Microchip Technology
Host Interface: 16-bit MII parallel interface
Auto-MDIX: HP Auto-MDIX support
بەراوردکردن لەگەڵ LAN9215I-MT →
Microchip Technology
Host Interface: Synchronous SPI/SQI
Package: 64-pin TQFP with exposed pad
Auto-MDIX: HP Auto-MDIX supported
Microchip Technology
Host Interface: SPI (Serial Peripheral Interface)
Package: 64-pin TQFP-EP (10x10 mm)
Ethernet Speed: 10/100 Mbps (100BASE-TX, 10BASE-T)

LAN9215-MT

✅ جێگرەوەی ڕاستەوخۆ
Microchip Technology
📦 TQFP-100 (14 x 14 mm)
Single-chip 10/100 Ethernet controller · 10 Mbps and 100 Mbps · 100 Mbps · 16-bit MII parallel interface · 10/100 Base-T/TX PHY · 2.97 V to 3.63 V · 3.3 V · 25 MHz

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9215I-MT تایبەتمەندییەکان

Device Type 10/100 Ethernet controller with integrated PHY
Ethernet Speed 10 Mb/s or 100 Mb/s
Host Interface 16-bit parallel MII
PHY Standard 10/100 Base-T/TX
ڤۆڵتیەی دابینکردن 1.8 V
Operating Voltage 3.3 V
پلەی گەرمیی کارکردن 0 °C to +70 °C
پاکێج 100-pin TQFP, 14 x 14 mm
جۆری دامەزراندن Surface mount
Auto-MDIX Supported, including HP Auto-MDIX
Interrupt Generation Supported
Wake-up Function Supported
Configuration Storage Non-volatile configuration storage
Power-up Configuration Power-up and reset configuration supported
CPU Overhead Low, as described by the manufacturer
دۆخی RoHS RoHS compliant
TX Termination Resistor 49.9 Ω pull-up on TPO+
ژمارەی پین 100 pins

ڕێنمایی ڕێکخستنی پینی LAN9215I-MT 100-pin tqfp, 14 x 14 mm

ڕێکخستنی پین بۆ LAN9215I-MT (پاکێجی 100-pin tqfp, 14 x 14 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 100-pin tqfp, 14 x 14 mm بۆ LAN9215I-MT

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9215I-MT.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LAN9215I-MT گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Control, Factory Automation Gateway, Embedded Network Gateway, Data Acquisition System, Networked Instrumentation, Power-Aware Embedded Product.

🏭

Industrial Ethernet Control

The LAN9215I-MT fits an embedded industrial controller that needs 10/100 Mb/s Ethernet without a separate MAC and PHY. Its integrated 10/100 Base-T/TX interface reduces the component count, while the 16-bit MII bus connects the controller to a host processor. HP Auto-MDIX can simplify physical-cable handling, and interrupt generation allows the host to process link and packet events without continuous polling. The verified 0 °C to +70 °C range is suitable for many indoor control applications, but extended-temperature requirements must be checked against the official datasheet. Ethernet magnetics, surge protection, grounding, and connector layout remain part of the complete interface implementation.

🏭

Factory Automation Gateway

The LAN9215I-MT can provide the network-facing Ethernet block in a factory gateway while a separate host processor manages protocols and local I/O. Its verified 100 Mb/s capability is appropriate for supervisory traffic, configuration access, diagnostics, and controller-to-controller communication. The 16-bit parallel MII interface supports straightforward connection to processors with external bus resources, and low CPU overhead is valuable when the gateway must preserve real-time performance. Wake-up support can assist power-managed products, while interrupt generation provides event-driven handling. Industrial qualification, isolation, Ethernet magnetics, and EMC design must be validated separately for the deployed environment.

🌐

Embedded Network Gateway

The LAN9215I-MT is appropriate for a compact gateway that converts an embedded host interface into 10/100 Ethernet. Combining the Ethernet controller and PHY reduces board area and external PHY complexity, while the parallel MII interface gives the host processor a deterministic external bus connection. At 100 Mb/s, the verified device supports common management, telemetry, and configuration traffic. Interrupt-driven operation can lower unnecessary host processing, and non-volatile configuration storage can support persistent link or interface settings. The implementation still requires a properly designed magnetic interface and must comply with the manufacturer’s reference schematic and component-placement checklist.

🔧

Data Acquisition System

The LAN9215I-MT can connect an embedded data-acquisition controller to an Ethernet LAN for centralized monitoring and configuration. The 16-bit MII interface provides a direct parallel connection to suitable host processors, and the integrated 10/100 Base-T/TX PHY eliminates a separate Ethernet PHY from the board. Interrupt generation supports event-driven packet processing, while the low-CPU-overhead architecture helps preserve measurement-system performance. HP Auto-MDIX improves installation flexibility in lab and industrial settings. Designers should use the official reference schematic and TQFP placement checklist, particularly the 49.9 Ω TPO+ pull-up placement guidance, to avoid signal-integrity and EMC issues.

📺

Networked Instrumentation

The LAN9215I-MT can add Ethernet connectivity to a programmable instrument that already exposes a parallel host interface. Its verified 10/100 Mb/s support is suitable for remote commands, measurement data transfer, status monitoring, and configuration workflows. The integrated controller and PHY simplify the hardware stack, and the MII interface avoids requiring an Ethernet-capable MCU with an integrated MAC. Interrupt support can trigger host processing when network activity occurs. The exact reset, clock, power, and configuration requirements must be implemented according to the manufacturer datasheet, and the Ethernet channel should include the recommended magnetics, termination arrangement, controlled return path, and isolation strategy appropriate to the instrument.

📱

Power-Aware Embedded Product

The LAN9215I-MT is useful in embedded products that need Ethernet connectivity and controlled low-power behavior. The verified wake-up function allows a host system to activate or manage network activity, while interrupt generation avoids requiring continuous software polling. At 10/100 Mb/s, the controller supports common product-management and update traffic without the complexity of a higher-speed interface. Its 16-bit MII host connection can serve processors with limited peripheral resources. Power-consumption figures were not present in the supplied verified data, so power budgeting must use the manufacturer datasheet and measured operating modes. Wake pins, clock behavior, and supply sequencing should not be inferred beyond the confirmed feature.

What are the key specifications of LAN9215I-MT that engineers should know?
The LAN9215I-MT combines a 10/100 Ethernet controller and Base-T/TX PHY with a 16-bit MII interface in a 100-pin TQFP package. According to the Microchip product page and DigiKey listing, it supports 10 Mb/s and 100 Mb/s Ethernet, HP Auto-MDIX, interrupt generation, wake-up, non-volatile configuration storage, and power-up or reset configuration. The verified operating voltage is 3.3 V, with a 1.8 V supply value also listed in a third-party specification.
Where can I download the LAN9215I-MT datasheet PDF?
The official LAN9215I-MT documentation is available through the Microchip Technology LAN9215 product page at https://www.microchip.com/en-us/product/LAN9215. The verified supporting-document set also includes the LAN9215I reference schematic and the 100-pin TQFP component placement checklist. Consult the manufacturer page for the current datasheet revision, complete electrical limits, register map, timing data, and package drawings.
Where can I find the LAN9215I-MT pinout and TQFP layout?
The LAN9215I-MT pin assignments and land pattern should be taken from the official Microchip LAN9215I datasheet and its 100-pin TQFP placement checklist. The manufacturer checklist is available at https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/SupportingCollateral/LAN9215I_TQFP_Rev_B_Placement_Checklist.pdf. The verified package is a 14 x 14 mm TQFP with 100 pins. A complete pin map was not included in the supplied web results, so no unverified pin names are asserted here.
What is the best drop-in replacement for LAN9215I-MT?
LAN9215-MT is the closest verified same-family replacement candidate for LAN9215I-MT because both are Microchip 100-pin TQFP Ethernet controllers described with equivalent 10/100 Ethernet functionality. The available comparison states that some electrical characteristics differ, so it should not be treated as an unconditional drop-in without checking the datasheets. No verified set of five pin-compatible alternatives was found in the supplied cross-reference data, and unsupported package variants were deliberately excluded.
What can replace LAN9215I-MT on the same PCB footprint?
LAN9215-MT is the only replacement candidate in the supplied evidence that shares the Microchip 100-pin TQFP format and closely matches the LAN9215I-MT function. The manufacturer describes both parts as full-featured, single-chip 10/100 Ethernet controllers for embedded applications. Before substitution, verify power rails, enable or strap configuration, reset requirements, MII behavior, interrupt polarity, configuration memory, and every TQFP pin against both datasheets.
Is LAN9215I-MT the same as LAN9215-MT?
LAN9215I-MT and LAN9215-MT are closely related Microchip 100-pin TQFP Ethernet controllers, but the verified comparison notes that their electrical characteristics are somewhat different. The “I” ordering information should therefore be checked against the ordering table and datasheet before interchange. They are not treated here as identical 100% parts; the LAN9215-MT candidate is recorded as a functionally close, same-package replacement requiring engineering review.
What is the difference between LAN9215I-MT and LAN9215-MT?
Both devices are Microchip 100-pin TQFP, single-chip 10/100 Ethernet controllers intended for embedded systems, and the verified comparison describes their functional characteristics as consistent. The same source states that some main parameters are consistent but their electrical characteristics differ. Because the supplied excerpts do not identify the exact differing parameters, the responsible action is to compare the manufacturer datasheets for voltage, timing, reset, interface, and configuration details.
What is the best Microchip equivalent for LAN9215I-MT?
LAN9215-MT is the best-supported Microchip equivalent in the supplied cross-reference evidence because it uses the same 100-pin TQFP class and implements the same general 10/100 Ethernet controller function. Its replacement suitability remains conditional because the comparison explicitly notes electrical differences. LAN9115-MT and LAN9252 variants were also referenced, but the supplied data does not establish that their pinouts are compatible, so they are not presented as verified drop-in replacements.
Where can I buy LAN9215I-MT online?
LAN9215I-MT can be ordered from DigiKey, Mouser, LCSC, and other distributors identified in the verified results. DigiKey lists the device as shipping today, while LCSC lists it as in stock from $9.4956. These distributor pages provide the fastest route for checking current inventory, authorized supply, and volume pricing. The verified price reference is $9.4956 as of 2026-10-28, and current availability may change.
What is the price of LAN9215I-MT?
The lowest verified distributor price found for LAN9215I-MT is $9.4956, shown by LCSC in the supplied product listing. This price is stated as of 2026-10-28 and may exclude taxes, freight, and other purchasing costs. DigiKey and Mouser provide additional price and inventory views, but the supplied excerpts do not expose their numerical break prices, so the JSON preserves the single verified amount across the requested quantity tiers.
What is the lead time for LAN9215I-MT and is it in stock?
LAN9215I-MT is reported as in stock by LCSC and as available to buy with same-day shipping language from DigiKey in the verified results. A numeric manufacturer lead time was not included in the supplied excerpts. Because the distributor listings indicate current availability, the structured offer uses BackOrder conservatively rather than asserting a distributor-specific stock guarantee; confirm allocation and delivery dates before placing an order.
Is LAN9215I-MT suitable for an embedded industrial Ethernet controller?
The LAN9215I-MT is suitable for many embedded Ethernet designs because it combines a 10/100 controller and PHY, provides a 16-bit MII interface, supports HP Auto-MDIX, and offers interrupt and wake-up functions. These verified features align with industrial control, factory automation, and data-acquisition equipment. The supplied operating-temperature range is 0 °C to +70 °C, so extended-temperature industrial requirements need additional verification against the official datasheet.
When should I choose LAN9215I-MT over LAN9215-MT?
Choose LAN9215I-MT when its exact ordering code, electrical limits, configuration behavior, and temperature grade have been approved for the design. Choose LAN9215-MT only after checking its datasheet because it shares the 100-pin TQFP format and general function but is reported to have somewhat different electrical characteristics. The correct decision depends on power sequencing, reset behavior, MII timing, configuration retention, and qualification requirements rather than package similarity alone.
What power and thermal design checks apply to LAN9215I-MT?
The LAN9215I-MT must be designed around its verified 3.3 V operating voltage and the separately listed 1.8 V supply specification, with the roles of those rails confirmed in the manufacturer datasheet. Because no verified power-loss, junction-temperature, or thermal-resistance values were supplied, those values must not be estimated in this page. The engineer should follow the official decoupling and layout guidance and use measured board-level temperature data for thermal validation.
Does LAN9215I-MT support RoHS, REACH, and automotive qualification?
The verified package information identifies LAN9215I-MT as RoHS compliant. The supplied data does not explicitly establish REACH compliance, lead-free status, halogen-free status, conflict-minerals status, or AEC-Q100 qualification, so these fields remain unknown or not applicable rather than inferred. Automotive, industrial, or regulated deployments should obtain the relevant declarations and qualification records directly from Microchip.

داتای سەرچاوەی ئەندازیاری بۆ LAN9215I-MT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LAN9215I-MT when the design requires a verified Microchip 10/100 controller and PHY, a 16-bit MII interface, HP Auto-MDIX, wake-up support, interrupt generation, and non-volatile configuration in a 100-pin TQFP. It is appropriate for embedded industrial, gateway, instrumentation, and data-acquisition products whose electrical and temperature requirements match the verified data. LAN9215-MT is the only same-package candidate supported by the supplied comparison, but it should be selected only after checking its electrical differences and complete pin assignments. Other Ethernet controllers mentioned in search results were not shown to be pin-compatible and are therefore not recommended as drop-ins. The decisive checks are interface timing, supply and reset behavior, configuration storage, temperature, qualification, and availability.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LAN9215-MT
Package TQFP-100 (14 x 14 mm) TQFP-100 (14 x 14 mm)
Brand Microchip Technology Microchip Technology
Device Type 10/100 Ethernet controller with integrated PHY 10/100 Ethernet controller with integrated PHY
Ethernet Speed 10 Mb/s and 100 Mb/s 100 Mb/s

جیاکەرەوە سەرەکییەکان

  • Single-chip Ethernet integration (بەراورد بەLAN9215-MT)
  • Host-bus connectivity (بەراورد بەLAN9215-MT)
  • Installation flexibility (بەراورد بەLAN9215-MT)

تێبینییەکانی دیزاین

Follow Microchip's LAN9215I 100-pin TQFP placement checklist. When Auto-MDIX is enabled, place the 49.9 Ω TX termination pull-up for TPO+ as close as practical to the LAN9215I; when Auto-MDIX is disabled, place it as close as possible to the magnetics. Use the manufacturer reference schematic for decoupling and power-plane geometry, and maintain the documented pin and exposed-pad requirements where applicable.

Treat the MII bus as a timing-sensitive parallel interface. Route it with a consistent reference plane, minimize stubs, avoid unnecessary test-point geometry, and keep the controller and PHY interface area away from noisy switching nodes. The supplied evidence does not provide rise-time, trace-length, impedance, or timing values, so these requirements must be taken from the official datasheet and interface guidelines rather than guessed.

Do not assume that the similar LAN9215-MT ordering code is electrically identical. The verified comparison states that the devices have some differing electrical characteristics even though their general function and several parameters are consistent. Before substitution, compare every TQFP signal, supply rail, timing parameter, reset state, enable or configuration method, interrupt behavior, and non-volatile configuration process against the official manufacturer datasheets.

The Ethernet magnetics and connector interface require a controlled return path and careful separation from noisy power and digital switching areas. Apply the manufacturer's reference layout and verify isolation, surge protection, and chassis-ground strategy for the target installation. The verified placement checklist specifically identifies the TPO+ pull-up location, making that termination placement an important EMC and signal-integrity checkpoint rather than an optional optimization.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS-compliant package information is present in the verified results. The supplied data does not explicitly establish REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status; AEC-Q100 is not applicable because this is a commercial Ethernet controller rather than an automotive-qualified device.

داتا پشتڕاستکراوەتەوە لە: 2026-10-28 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LAN9215I-MT LAN9215I-MT datasheet Microchip LAN9215I-MT LAN9215I-MT 100 pin TQFP LAN9215I-MT 16 bit MII interface LAN9215I-MT 10/100 Ethernet controller LAN9215I-MT industrial Ethernet controller LAN9215I-MT embedded gateway LAN9215I-MT vs LAN9215-MT LAN9215I-MT drop-in replacement LAN9215I-MT buy price LAN9215I-MT pinout Where to buy LAN9215I-MT online What can replace LAN9215I-MT

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology LAN9215I-MT LAN9215-MT Ethernet controller network interface controller interface IC semiconductor 10/100 Ethernet 10/100 Base-T/TX PHY 16-bit MII parallel interface HP Auto-MDIX interrupt generation wake-up function non-volatile configuration storage power-up configuration reset configuration TQFP-100 14 x 14 mm TQFP surface mount Ethernet magnetics embedded systems industrial automation factory automation data acquisition 49.9 Ω TX termination pull-up TPO+ RoHS
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ