LAN9252I/ML - 2/3-Port EtherCAT Controller | Microchip
MPN: LAN9252I/ML ✓ چالاکLAN9252I/ML گشتی
An EtherCAT device controller, or ESC, is a specialized interface IC that connects an embedded control system to an EtherCAT network. Within the hierarchy of EtherCAT slave controllers, network interface controllers, communication ICs, and semiconductors, the LAN9252 combines Ethernet physical-layer transceivers with EtherCAT protocol and host-interface functions. Its synchronous device SPI/SQI interface allows an external microcontroller or processor to access controller resources.
The principal feature set includes two integrated 100BASE-TX PHYs, support for 100BASE-FX through an external fiber transceiver, 10/100 Mb/s data rates, and HP Auto-MIDX cabling support. Digital I/O operation also allows selected EtherCAT signals to be controlled or monitored directly by an EtherCAT master. These features make the device suitable for industrial automation equipment where EtherCAT connectivity must coexist with embedded processing.
The controller is intended for 1.8 V, 2.5 V, and 3.3 V operation, as identified in the supplied component listings. Its 64-QFN construction supports compact industrial designs, although exposed-pad layout and multilayer PCB construction are important for reliable performance. The I ordering code identifies the industrial-temperature device variant, while the exact ordering suffix, package markings, and absolute maximum ratings must be confirmed in the manufacturer datasheet before release.
Typical applications include EtherCAT servo drives, programmable logic controllers, industrial I/O modules, motion-control equipment, and factory-automation controllers. A copper-only installation can use the integrated PHYs directly, while a fiber-based installation can add an external 100BASE-FX transceiver. This page also compares package and ordering variants, records verified sourcing links, and highlights design checks that are not apparent from a distributor category listing alone.
جێگرەوەکانی جێگۆڕکێ بۆ LAN9252I/ML — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9252I/ML (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Cable Support, Host Interface, Package, Product Type.
هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.
داوای جێگرەوەکان بکەLAN9252I/ML تایبەتمەندییەکان
| Product Type | 2/3-port EtherCAT slave controller |
| Integrated Ethernet PHY Count | 2 PHYs |
| Copper Ethernet Support | 10/100 Mb/s 100BASE-TX |
| Fiber Ethernet Support | 100BASE-FX through an external fiber transceiver |
| Transceiver Type | Full-duplex 100BASE-TX per integrated PHY |
| Host Interface | Synchronous device SPI/SQI |
| Digital I/O Mode | Supported |
| Auto-MDIX | HP Auto-MDIX supported |
| Supported Supply Voltage | 1.8 V, 2.5 V, or 3.3 V |
| پاکێج | 64-QFN, 9 x 9 mm |
| جۆری دامەزراندن | Surface mount |
| Temperature Grade | Industrial |
| Number of Ethernet Ports | 2 integrated 100BASE-TX ports |
| Cable Support | Direct-connect or crossover LAN cable |
ڕێنمایی ڕێکخستنی پینی LAN9252I/ML 64-qfn, 9 x 9 mm
ڕێکخستنی پین بۆ LAN9252I/ML (پاکێجی 64-qfn, 9 x 9 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9252I/ML.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LAN9252I/ML گونجاوە بۆ 6 بەکارھێنانs: EtherCAT Servo Drive Interface, Programmable Logic Controller Communication, Industrial I/O Module, Motion Control Controller, Factory Automation Gateway, 100BASE-FX Fiber Gateway.
EtherCAT Servo Drive Interface
The LAN9252I/ML fits an EtherCAT servo-drive controller that must connect a motion-control processor to a 100 Mb/s industrial network while minimizing discrete interface hardware. Its two integrated full-duplex 100BASE-TX PHYs provide copper connectivity directly from the 64-QFN device, while the synchronous SPI/SQI interface gives the host processor access to EtherCAT controller resources. HP Auto-MDIX also allows installation crews to use either straight-through or crossover cable. The design must follow the manufacturer layout for 100BASE-TX differential pairs, magnetics, grounding, and the QFN exposed pad; otherwise, insertion loss and return loss could impair communications in a motor-control environment affected by high-current switching.
پێشنیارکراو
Programmable Logic Controller Communication
The LAN9252I/ML is appropriate for a PLC communication module that adds deterministic EtherCAT connectivity to an embedded control board. The processor communicates through the device's synchronous SPI/SQI interface, while the integrated PHYs handle 10/100 Mb/s full-duplex 100BASE-TX links without requiring two separate Ethernet PHY packages. Digital I/O mode can allow selected EtherCAT signals to be controlled or monitored by the master, which is useful in modular I/O architectures. In a PLC cabinet, the layout should isolate Ethernet magnetics and the PHY section from switching nodes and motor-control return currents. Robust grounding, controlled impedance, and verified isolation boundaries are more important than simply minimizing the controller footprint.
پێشنیارکراو
Industrial I/O Module
The LAN9252I/ML supports a distributed industrial I/O module in which field devices communicate over EtherCAT and a local microcontroller handles sensing and actuation. Two integrated 100BASE-TX PHYs permit copper network connections within a controller or to adjacent equipment, while the SPI/SQI interface connects the EtherCAT controller to the module processor. The digital I/O capability adds flexibility when the EtherCAT master must observe or control selected signals. Copper and fiber deployments have different hardware implications: integrated PHYs serve 100BASE-TX copper links, whereas 100BASE-FX requires an external fiber transceiver. The PCB should therefore reserve the appropriate transceiver area and maintain separation between communications circuitry and high-energy field-output switching stages.
پێشنیارکراو
Motion Control Controller
The LAN9252I/ML is suitable for a compact EtherCAT motion controller where coordinated drive data must move reliably between the master and embedded control logic. Its two integrated full-duplex 100BASE-TX PHYs avoid an external-PHY footprint, and HP Auto-MDIX simplifies cabling between distributed motion nodes. The 64-QFN 9 x 9 mm package also allows the controller to be placed near the processor, although the exposed thermal pad requires adequate copper and a controlled multilayer stackup. Ethernet differential pairs must be routed without stubs, test points that disrupt impedance, or breaks between layers. Firmware must also configure the intended EtherCAT mode and verify SPI/SQI timing according to the manufacturer interface guidance.
پێشنیارکراو
Factory Automation Gateway
The LAN9252I/ML can serve as the EtherCAT endpoint in a factory gateway that bridges an embedded controller to multiple automation devices. Two integrated PHYs provide network ports without requiring two discrete 100BASE-TX transceivers, and the SPI/SQI host interface allows a processor to exchange cyclic and diagnostic data with the EtherCAT network. HP Auto-MDIX improves installation flexibility in factories where cabling practices vary. For gateway hardware, the Ethernet section should be laid out according to the manufacturer reference layout, with magnetics close to PHY pins and a continuous reference plane. Industrial surge, isolation, grounding, and cabinet-cabling requirements must also be addressed separately because the verified listing does not specify an integrated surge-protection solution.
پێشنیارکراو
100BASE-FX Fiber Gateway
The LAN9252I/ML can participate in a 100BASE-FX fiber gateway when a copper-only installation is unsuitable because of distance, isolation, or industrial cabling constraints. The integrated Ethernet PHYs support 100BASE-TX copper operation, while the manufacturer datasheet states that 100BASE-FX is supported through an external fiber transceiver. This arrangement preserves the EtherCAT controller and host-interface functions on one IC while adding a dedicated optical-network front end. The external transceiver must be selected for compatible data rate, signal levels, and timing. PCB layout should separate the fiber interface from sensitive digital and power sections, maintain controlled impedance, and follow the device's exposed-pad and Ethernet-layout guidance.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LAN9252I/ML — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Brand | Microchip Technology |
| Package | 64-QFN, 9 x 9 mm |
| Controller Type | 2/3-port EtherCAT slave controller |
| Integrated Ethernet PHYs | 2 |
| Copper Ethernet Data Rate | 10/100 Mb/s |
| 100BASE-TX Support | Full-duplex integrated transceivers |
| 100BASE-FX Support | Supported through an external fiber transceiver |
| Host Interface | Synchronous device SPI/SQI |
| Auto-MDIX | HP Auto-MDIX supported |
| Supported Supply Voltage | 1.8 V, 2.5 V, or 3.3 V |
| Temperature Grade | Industrial |
| Digital I/O Mode | Supported |
جیاکەرەوە سەرەکییەکان
- Integrated dual-PHY EtherCAT interface (بەراورد بەENC424J600-I/ML)
- EtherCAT-specific integration (بەراورد بەENC28J60/ML)
- Flexible copper and fiber expansion (بەراورد بەLAN9252TI/ML)
تێبینییەکانی دیزاین
Implement the manufacturer-recommended 64-QFN land pattern and Ethernet reference layout without substituting a generic 64-QFN footprint. The LAN9252I/ML combines sensitive PHY circuitry with a thermal-pad package, so the exposed pad should connect to the intended ground or supply-plane structure specified by the datasheet. Keep 100BASE-TX differential traces short, symmetric, continuously referenced, and away from switching power-converter paths. Confirm magnetics placement and isolation clearances against the manufacturer reference design before release.
Decouple each required supply rail directly at the corresponding device pins and follow the manufacturer guidance for component values and layout. The verified listing identifies 1.8 V, 2.5 V, and 3.3 V operation, but it does not provide regulator requirements, current limits, or capacitor values. Treat those parameters as [DATA_NEEDED] and retrieve them from the datasheet and hardware design guide before selecting supplies. Verify sequencing, startup behavior, and exposed-pad potential on the assembled multilayer PCB.
Preserve controlled impedance for the SPI/SQI host connection and all 100BASE-TX channels. Avoid routing Ethernet nets through test pads without a manufacturer-approved compensation method, and do not create layer transitions through split planes. For 100BASE-FX, add an external transceiver selected for compatible 100 Mb/s operation and follow its layout and isolation requirements. Validate signal integrity with the actual magnetics, connectors, stackup, and enclosure because distributor snippets do not provide complete reference-impedance values.
زانیاری پابەندبوون
The supplied verified data does not explicitly state compliance status. The I ordering suffix is identified as an industrial-grade variant, but it is not sufficient to infer AEC-Q100 qualification.