LAN9254-V/JRX - 3-Port EtherCAT ESC | Microchip
MPN: LAN9254-V/JRX ✓ چالاکLAN9254-V/JRX گشتی
An EtherCAT device controller, or ESC, is the interface between an EtherCAT network and an embedded automation system. It manages EtherCAT communication while exposing process data through a process data interface to a microcontroller or other control logic. As an Ethernet controller IC, the LAN9254 combines EtherCAT protocol handling with integrated physical-layer transceivers, reducing the number of separate network components required on the controller board.
The LAN9254 provides three EtherCAT ports and integrates two 10/100 Ethernet PHYs. Each PHY supports full-duplex 100BASE-TX operation at 100 Mbps. HP Auto-MDIX support allows the design to use either straight-through or crossover Ethernet cables, simplifying installation in factory automation, industrial control, and laboratory networks where field cabling may vary.
The target device is identified as LAN9254-V/JRX, while related ordering codes include LAN9254/JRX and LAN9254T-V/JRX in the same 80-TQFP-EP package. Microchip also publishes a hardware design checklist and a LAN9252-to-LAN9254 migration guide. These documents are important when assigning configuration straps, reviewing pin differences during migrations, and checking the 80-pin TQFP layout against the target schematic.
Typical applications include EtherCAT slave controllers for industrial automation, servo-drive interfaces, distributed I/O modules, motion-control equipment, and factory communication gateways. Its integrated PHYs are especially useful where board area is constrained and external Ethernet magnetics or separate PHY components would otherwise increase design complexity. The controller must still be paired with an appropriate processor interface and suitable magnetic isolation.
PCB planning should follow Microchip's LAN9254 hardware design checklist, particularly for the 80-pin TQFP footprint, exposed-pad connection, configuration straps, clock circuitry, and Ethernet differential routing. Review the manufacturer pin-description table before assigning tracks, and verify every supply and ground connection against the device data sheet and hardware checklist.
This product record combines the verified device identity, package information, EtherCAT capabilities, and application guidance with same-package ordering alternatives. It also provides practical implementation notes that support component selection, schematic review, PCB planning, and replacement assessment without relying on generic Ethernet-controller descriptions.
جێگرەوەکانی جێگۆڕکێ بۆ LAN9254-V/JRX — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9254-V/JRX (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Digital I/O Count, Ethernet Physical Layer, Package.
LAN9254/JRX
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LAN9254T-V/JRX
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LAN9254-V/JRX تایبەتمەندییەکان
| Device Type | 3-port EtherCAT device controller |
| Integrated Ethernet PHY Count | 2 PHYs |
| Ethernet Speed | 100 Mbps |
| Ethernet Physical Layer | 100BASE-TX |
| Duplex Mode | Full duplex |
| EtherCAT Port Count | 3 ports |
| Auto-MDIX Support | HP Auto-MDIX |
| Cable Support | Direct-connect or crossover LAN cables |
| Digital I/O Count | 32 digital I/Os |
| پاکێج | 80-lead TQFP with exposed pad |
| Package Body Size | 12 x 12 mm |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی LAN9254-V/JRX 12 x 12 mm
ڕێکخستنی پین بۆ LAN9254-V/JRX (پاکێجی 12 x 12 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9254-V/JRX.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LAN9254-V/JRX گونجاوە بۆ 6 بەکارھێنانs: Industrial EtherCAT Slave Controller, Distributed I/O Module, Servo Drive Interface, Motion-Control Equipment, Factory Communication Gateway, Embedded Test and Measurement System.
Industrial EtherCAT Slave Controller
The LAN9254-V/JRX fits an EtherCAT slave-controller position in factory automation equipment because it provides three EtherCAT ports and two integrated Ethernet PHYs. Each PHY operates full duplex at 100 Mbps over 100BASE-TX, while HP Auto-MDIX supports direct-connect and crossover cables for easier field installation. The integrated PHYs can reduce board-level Ethernet component count, although the design must still include the required magnetic isolation and a compatible host interface.
پێشنیارکراو
Distributed I/O Module
For distributed I/O modules, the LAN9254-V/JRX supplies a compact three-port EtherCAT interface with integrated 100BASE-TX PHYs. Multiple ports support line-style network connections without requiring three separate Ethernet interface circuits, while the 32 digital I/Os identified for the related LAN9254T-V/JRX provide a direct path to field logic. Designers should verify the required process-data interface and pin multiplexing before selecting the host processor.
پێشنیارکراو
Servo Drive Interface
The LAN9254-V/JRX can serve as the EtherCAT communications engine in a servo-drive interface when the controller board is designed around a 3-port, 100BASE-TX network architecture. Integrated full-duplex PHYs shorten the physical-interface portion of the design and support both straight-through and crossover cabling through HP Auto-MDIX. Real-time behavior still depends on the host processor, synchronization method, process-data latency, and firmware architecture.
پێشنیارکراو
Motion-Control Equipment
The three-port EtherCAT topology of the LAN9254-V/JRX is suitable for motion-control equipment that must exchange synchronized commands and feedback across an EtherCAT network. Two integrated 100 Mbps PHYs minimize the need for discrete copper-network interfaces, while the 12 x 12 mm TQFP-EP package supports compact controller boards. Validate synchronization tolerance, host-interface timing, and thermal performance at the machine's operating temperature before production release.
پێشنیارکراو
Factory Communication Gateway
The LAN9254-V/JRX can be used in an EtherCAT gateway when a communications board needs three ports and two integrated copper Ethernet PHYs. Full-duplex 100BASE-TX operation supports industrial Ethernet traffic, and HP Auto-MDIX simplifies connection to varied field cabling. The gateway implementation should follow the hardware design checklist for exposed-pad soldering, strap configuration, clock routing, differential pairs, and external magnetic components.
پێشنیارکراو
Embedded Test and Measurement System
For embedded test and measurement equipment requiring EtherCAT participation, the LAN9254-V/JRX combines a three-port device controller with dual integrated 100BASE-TX PHYs. This allows one controller to support a multi-segment network while linking to test-control logic. Because production instruments may impose strict timing and grounding requirements, engineers should evaluate process-data latency, jitter, isolation, synchronization behavior, and conducted-emissions performance as part of system validation.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LAN9254-V/JRX — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
Use LAN9254/JRX when the same package and controller family are needed but the -V ordering option is not required. Consider LAN9254T-V/JRX when its temperature classification and 32 digital I/O implementation match the machine, after comparing every configuration strap and electrical limit with the target design. No cross-brand drop-in substitute has been established because a matching package does not guarantee EtherCAT register, timing, or firmware compatibility. Before production, verify the ordering table, lifecycle status, exposed-pad layout, thermal requirements, and hardware design checklist requirements for the exact selected suffix.
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LAN9254/JRX | LAN9254T-V/JRX |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-TQFP-EP (12x12) | 80-TQFP-EP (12x12) | 80-TQFP-EP (12x12) |
| Device Type | 3-port EtherCAT device controller | Ethernet controller | 2/3-port EtherCAT slave controller |
| Ordering Suffix | -V/JRX | /JRX | T-V/JRX |
جیاکەرەوە سەرەکییەکان
- Integrated dual-PHY architecture (بەراورد بەLAN9254/JRX)
- Field-cabling flexibility (بەراورد بەLAN9353T/PT)
- Three-port EtherCAT integration (بەراورد بەLAN9254T-V/JRX)
تێبینییەکانی دیزاین
Follow Microchip's LAN9254 Hardware Design Checklist before releasing the layout. Check the schematic against the 80-pin TQFP pin table, verify every configuration strap against its required pull-up or pull-down state, and confirm the exposed-pad connection and thermal-via arrangement. Treat the checklist as a design review tool rather than a substitute for the device electrical characteristics and pin-description table.
Route the Ethernet differential pairs as controlled-impedance nets with continuous reference planes and minimize layer transitions and stubs. Keep the PHY and magnetic-isolation sections away from switching nodes and high-current return paths. Use the manufacturer's recommended component placement and spacing around the 100BASE-TX interfaces so common-mode noise and differential impedance variation do not compromise link reliability.
Partition supply routing and decoupling according to the device pin requirements and application guidance. Place the required local capacitors at their associated supply pins, preserve a low-impedance ground return, and confirm voltage tolerances for every external rail. Before power-up, verify strap levels and clock configuration because an incorrect boot configuration can leave the EtherCAT interface unavailable even when the power rails are correct.
Do not substitute the LAN9254/JRX or LAN9254T-V/JRX solely because the package drawings match. Compare ordering information, temperature classification, configuration straps, process-data-interface options, electrical limits, and lifecycle status. A related LAN9254 code can share the 80-TQFP-EP footprint while differing in a grade or ordering option that matters to production qualification.
زانیاری پابەندبوون
Compliance declarations were not identified in the product records. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status from the manufacturer's current product documentation before production release.