Microchip Technology

LAN9352I/PT - 2-Port 10/100 Managed Ethernet Switch | Microchip

MPN: LAN9352I/PT ✓ چالاک
1.2 V to 3.3 V Vdss 80-pin TQFP exposed-pad, 12 x 12 mm Package 10 Mbps to 100 Mbps per port Speed
MOQ: 1 |

LAN9352I/PT گشتی

Microchip Technology LAN9352I/PT is a two-port managed 10/100 Ethernet switch with two integrated 10BASE-T/100BASE-TX PHYs, I2C and SPI host interfaces, and an 80-pin TQFP exposed-pad package measuring 12 x 12 mm. It operates from a 1.2 V to 3.3 V supply and supports IEEE 802.3 and IEEE 802.3u Ethernet traffic at up to 100 Mbps per port.

A managed Ethernet switch is an integrated network-semiconductor device that combines PHYs, packet handling, port management, and a host interface in one component. It sits between an embedded processor or control system and one or more Ethernet ports, providing a compact alternative to discrete transceivers, magnetics, and separate switch silicon. The LAN9352 family is positioned for cost-sensitive consumer, embedded, and industrial equipment requiring integrated two-port connectivity.

The LAN9352I/PT combines two 10/100 ports with I2C and SPI host control, allowing firmware to configure switch registers, monitor port activity, and manage network behavior. Its industrial-temperature designation distinguishes it from the standard LAN9352 variant, while the 12 x 12 mm exposed-pad TQFP package supports compact board layouts and improved thermal coupling through its exposed thermal pad. The tray packaging code identifies the /PT ordering option.

The integrated switch architecture reduces the number of external Ethernet interface components required in embedded equipment. Both ports support 10 Mbps and 100 Mbps operation, allowing automatic compatibility with legacy 10BASE-T equipment and 100BASE-TX networks. Host configuration through I2C or SPI simplifies connection to embedded processors, microcontrollers, and industrial controllers that already expose one of these serial interfaces.

Typical uses include industrial automation controllers, embedded network appliances, point-of-sale terminals, printers, set-top equipment, and connected industrial modules. In these systems, the switch can provide two network-facing ports while the host processor accesses management and status registers. Selection should account for the exposed-pad land pattern, 80-pin routing density, required magnetic isolation, and the 3.3 V power architecture.

Place the LAN9352I/PT close to its Ethernet magnetics and connector-side circuitry to minimize high-frequency routing risk. Keep the exposed pad connected to the intended ground plane, use short and continuous supply connections, and follow the manufacturer’s recommended decoupling and component-layout guidance. Confirm all interface levels, strap options, and power rails against the device documentation before layout release.

This product guide combines the device architecture, package and interface constraints, application guidance, procurement fields, and verified drop-in considerations. It is designed to help hardware and sourcing engineers evaluate the LAN9352I/PT against same-package alternatives without overlooking pin compatibility, thermal-pad implementation, or managed-switch feature requirements.

جێگرەوەکانی جێگۆڕکێ بۆ LAN9352I/PT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9352I/PT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Host Interface, Product Type, Integrated PHY, Number of Ports.

Microchip Technology
Package: 80-pin TQFP with exposed pad
Product Type: 2-port managed Ethernet switch
Integrated PHY: 10/100 Base-T/TX PHY
Microchip Technology
Package: 64-TQFP-EP, 10x10 mm
Host Interface: Dual RMII or single MII/RMII/Turbo MII
Product Type: 3-Port 10/100 Managed Ethernet Switch
Microchip Technology
Package: 64-TQFP-EP (10 mm x 10 mm)
Host Interface: I2C
Product Type: Managed Ethernet switch controller

LAN9352/PT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Microchip Technology
📦 80-pin TQFP exposed-pad (12 x 12 mm)
2-port managed Ethernet switch · 2 ports · 10/100 Mbps per port · 10/100 Base-T/TX · 10/100 Base-T/TX PHY · I2C · SPI · 16-bit non-PCI SPI/SQI interface

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9353T/PT

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Microchip Technology
📦 80-pin TQFP exposed-pad (12 x 12 mm)
Managed Ethernet switch controller · 3 ports · 10/100 Mbps · 10/100 Base-T/TX PHY · I2C · 64-TQFP-EP (10 mm x 10 mm) · 64 pins · 0.5 mm

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LAN9352I/PT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Device Type Managed Ethernet switch
Number of Ethernet Ports 2 ports
Supported Ethernet Speed 10 Mbps to 100 Mbps per port
Maximum Data Rate 100 Mbps per port
Integrated PHY 2 integrated 10BASE-T/100BASE-TX PHYs
Host Interface I2C and SPI
ڤۆڵتیەی دابینکردن 1.2 V to 3.3 V
Ethernet Standard IEEE 802.3 and IEEE 802.3u
پاکێج 80-pin TQFP exposed-pad, 12 x 12 mm
ژمارەی پین 80 pins
جۆری دامەزراندن Surface mount
Temperature Grade Industrial grade
Delivery Packaging Tray
Application Segment Consumer, embedded, and industrial designs
Switch Management Managed 2-port Ethernet switching
Interface Width 16-bit non-PCI SPI/SQI host interface

ڕێنمایی ڕێکخستنی پینی LAN9352I/PT 80-pin tqfp exposed-pad, 12 x 12 mm

ڕێکخستنی پین بۆ LAN9352I/PT (پاکێجی 80-pin tqfp exposed-pad, 12 x 12 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 80-pin tqfp exposed-pad, 12 x 12 mm بۆ LAN9352I/PT

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9352I/PT.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LAN9352I/PT گونجاوە بۆ 6 بەکارھێنانs: Industrial Automation Controller, Embedded Network Appliance, Point-of-Sale Terminal, Network Printer Controller, Connected Industrial Sensor Gateway, Set-Top and Media Endpoint.

🏭

Industrial Automation Controller

The LAN9352I/PT fits industrial controllers that need two managed Ethernet ports without adding a separate switch ASIC. Its two integrated 10BASE-T/100BASE-TX PHYs support links up to 100 Mbps, while I2C or SPI allows a microcontroller to configure ports and read status. The industrial-temperature option is appropriate for equipment operating outside consumer-temperature environments. Layout must preserve thermal performance by connecting the exposed pad to the recommended ground structure and placing Ethernet magnetics and signal components close to their associated PHY connections.

🖥️

Embedded Network Appliance

The LAN9352I/PT supports compact embedded appliances requiring two 10/100 network connections and local management. A host processor can use the SPI/SQI or I2C interface to access switch functions, while both integrated PHYs support 10 Mbps and 100 Mbps links. The 80-pin TQFP exposed-pad package limits PCB area but requires careful fanout and thermal via placement. This architecture is useful when the product must avoid an external unmanaged switch and provide controlled port behavior.

💳

Point-of-Sale Terminal

A two-port managed switch can simplify point-of-sale terminal networking by supporting both a service network and a peripheral connection through the LAN9352I/PT. Each port operates at 10 or 100 Mbps, allowing compatibility with existing 10BASE-T infrastructure as well as faster 100BASE-TX links. SPI or I2C control permits the terminal processor to monitor and configure network activity. The board design should provide the manufacturer-specified magnetic interface, power filtering, and exposed-pad thermal construction.

🖨️

Network Printer Controller

The LAN9352I/PT can provide two managed 10/100 interfaces in a network printer or print-server controller. One port may connect to an upstream network while the other supports local configuration or service access, and either port can negotiate 10 Mbps or 100 Mbps operation. I2C and SPI host options allow the printer controller to monitor link status and manage switching behavior. The exposed-pad TQFP construction must be designed for reliable heat transfer without compromising the high-density pin escape routing.

🧩

Connected Industrial Sensor Gateway

The LAN9352I/PT suits a sensor gateway that must bridge two Ethernet networks while offering host-level management. The two integrated 10/100 PHYs provide compact network connectivity, and the host interface permits firmware to read port conditions and apply switch settings. This arrangement is useful when sensors or machine controllers need Ethernet access but panel space is limited. The 1.2 V to 3.3 V operating range must be reconciled with the gateway power tree, and the PCB should isolate switching supplies from Ethernet magnetics.

📺

Set-Top and Media Endpoint

The LAN9352I/PT can serve compact set-top, media, or access-point designs that need two managed 10/100 ports for network and service connectivity. Supporting both 10 Mbps and 100 Mbps allows interoperability with older access networks, while I2C or SPI control integrates management with the endpoint processor. The small 12 x 12 mm package helps reduce board area, although its 80 leads and exposed pad require a multilayer PCB with careful thermal-via and escape-routing design.

کورتەی بەرهەمە پێشنیارکراوەکان

STM32F103R6T6ATR STMicroelectronics بەکارهێنراوە لە: Industrial Automation Controller TJA1057GTKZ NXP Semiconductors بەکارهێنراوە لە: Industrial Automation Controller KSZ8041RNL Microchip Technology بەکارهێنراوە لە: Industrial Automation Controller STM32F746ZGT6G STMicroelectronics بەکارهێنراوە لە: Embedded Network Appliance KSZ9897RTXI Microchip Technology بەکارهێنراوە لە: Embedded Network Appliance W25Q128JVSIQ External flash for configuration and firmware storage بەکارهێنراوە لە: Embedded Network Appliance STM32F103C8T6TR STMicroelectronics بەکارهێنراوە لە: Point-of-Sale Terminal PCA9554DWR Texas Instruments بەکارهێنراوە لە: Point-of-Sale Terminal, Network Printer Controller ADM485JNZ Analog Devices بەکارهێنراوە لە: Point-of-Sale Terminal STM32G0B1RET6 STMicroelectronics بەکارهێنراوە لە: Network Printer Controller W25Q64JVSSIQ Configuration and job-storage flash memory بەکارهێنراوە لە: Network Printer Controller STM32L051K8T6 STMicroelectronics بەکارهێنراوە لە: Connected Industrial Sensor Gateway DP83867IRRGZR Texas Instruments بەکارهێنراوە لە: Connected Industrial Sensor Gateway TLE7257SJXUMA1 Infineon بەکارهێنراوە لە: Connected Industrial Sensor Gateway STM32F413RGT6TR Microcontroller host for endpoint management بەکارهێنراوە لە: Set-Top and Media Endpoint KSZ8721SLI Microchip Technology بەکارهێنراوە لە: Set-Top and Media Endpoint SP232EET-L/TR MaxLinear بەکارهێنراوە لە: Set-Top and Media Endpoint
What is LAN9352I/PT?
The LAN9352I/PT is a Microchip Technology two-port managed 10/100 Ethernet switch with integrated PHYs and I2C or SPI host control. According to the manufacturer product page, the LAN9352 family targets consumer, embedded, and industrial designs requiring a compact, cost-effective Ethernet switch. The /PT version is supplied in an 80-pin TQFP exposed-pad package measuring 12 x 12 mm and supports operation from 1.2 V to 3.3 V.
How many Ethernet ports does LAN9352I/PT support?
The LAN9352I/PT supports two integrated 10/100 Ethernet ports, with each port capable of 10 Mbps or 100 Mbps operation. The manufacturer describes it as a two-port managed Ethernet switch with integrated 10BASE-T/100BASE-TX PHYs. This integration allows an embedded controller to manage both ports through one host interface while retaining support for 10BASE-T and 100BASE-TX networks.
What interfaces are available on LAN9352I/PT?
The LAN9352I/PT provides I2C and SPI interfaces for host communication and switch configuration. The manufacturer documentation also identifies a 16-bit non-PCI SPI/SQI interface for compatible controller-based designs. Use the I2C option when the host bus is simple and register access is relatively infrequent; use SPI or SQI when the product interface requires faster register access or more efficient data transfer.
What is the operating voltage of LAN9352I/PT?
The LAN9352I/PT operates from 1.2 V to 3.3 V. This range supports compact embedded systems using low-voltage core and I/O rails, while the 3.3 V maximum aligns with common industrial and consumer Ethernet interfaces. Confirm the internal rail requirements, external component operating voltages, and power-sequencing limits in the manufacturer datasheet before assigning supply nets in the schematic.
Which package does LAN9352I/PT use?
The LAN9352I/PT uses an 80-pin TQFP exposed-pad package measuring 12 x 12 mm. The exposed pad is part of the thermal and electrical footprint and must be implemented according to the manufacturer land-pattern guidance. Because the exact 80-pin TQFP drawing is not included in the package-diagram library, use the manufacturer pin description and package drawing as the authoritative PCB footprint references.
Where can I download the LAN9352I/PT datasheet PDF?
The official LAN9352I/PT datasheet PDF is available from the Microchip document link published for the LAN9352 family. It contains the device architecture, electrical characteristics, register information, interface descriptions, and package details needed for schematic and PCB design. The manufacturer also notes that an errata sheet may describe minor operational differences and recommended workarounds, so review current errata alongside the main datasheet.
Where can I find the LAN9352I/PT pinout?
The LAN9352I/PT pin assignment is defined in the manufacturer datasheet’s pin-description table and package drawing. The device uses an 80-pin TQFP exposed-pad package, so every PCB track and supply connection should be checked against those documents rather than a generic 80-pin drawing. Start with the exposed pad and its thermal-ground requirements, then verify signal names, power pins, strap inputs, and no-connect positions for the exact ordering code.
Is LAN9352I/PT suitable for industrial equipment?
The LAN9352I/PT is an industrial-temperature variant of Microchip’s LAN9352 managed-switch family and is described for consumer, embedded, and industrial applications. Its two integrated 10/100 PHYs are useful in automation controllers, network appliances, and connected industrial modules. Final suitability still depends on the device-specific operating-temperature limits, isolation requirements, EMC design, and environmental qualification of the complete product.
What is the best drop-in replacement for LAN9352I/PT?
The closest drop-in candidate is the same-brand LAN9352/PT because it retains the two-port managed 10/100 architecture and 80-pin TQFP exposed-pad footprint. A replacement must also match the exposed-pad land pattern, supply arrangement, host interface, strap configuration, and management-register expectations. A functionally similar Ethernet controller is not automatically a drop-in replacement, so verify the complete pin and register compatibility before substitution.
Can LAN9353T/PT replace LAN9352I/PT?
The LAN9353T/PT is a same-package two-port 10/100 managed-switch candidate for review, but it should not be treated as an unconditional drop-in replacement. Confirm pin-level differences, exposed-pad requirements, host-interface behavior, management registers, and strap settings against both manufacturer datasheets. The safest use is as a design-review alternative when the full electrical and software compatibility review confirms that no board or firmware changes are required.
LAN9352I/PT vs LAN9353T/PT - which is better for an embedded controller?
Choose LAN9352I/PT when compatibility with the original LAN9352I design and its established firmware is the primary requirement. Consider LAN9353T/PT only after reviewing its register map, interface configuration, and application differences. Both are associated with two-port managed 10/100 Ethernet-switch solutions in an 80-pin TQFP exposed-pad format, but a shared package does not by itself prove register-compatible operation.
When should I choose LAN9352I/PT over another managed Ethernet switch?
Choose LAN9352I/PT when the design needs two integrated 10/100 ports, I2C and SPI host access, a 1.2 V to 3.3 V supply range, and an established 80-pin TQFP exposed-pad footprint. It is particularly suitable for embedded products requiring managed port behavior without a separate Ethernet switch controller. Select another device only when it offers a required feature, interface, lifecycle, or package advantage that justifies a new schematic, firmware, and PCB design.
Is LAN9352I/PT suitable for a two-port embedded Ethernet gateway?
The LAN9352I/PT is suitable for a two-port embedded Ethernet gateway when 10/100 Mbps operation and managed-switch control are sufficient. Its two integrated PHYs connect through external Ethernet magnetic components, while I2C or SPI gives the embedded processor access to configuration and status functions. The design must account for magnetics, termination, creepage, isolation, thermal-pad layout, and the required 1.2 V to 3.3 V supply architecture.
What can replace LAN9352I/PT?
The LAN9352/PT is the primary same-brand replacement candidate because it retains the LAN9352 two-port managed 10/100 architecture and 80-pin TQFP exposed-pad format. The LAN9353T/PT can also be evaluated when its electrical interface and firmware behavior match the target board. Verify every pin, strap, supply, register, and exposed-pad connection before approving either part as a production substitute.
Where can I buy LAN9352I/PT and what is its lead time?
Use the Request a Quote form on this page to request LAN9352I/PT availability, current lead time, and order confirmation for the tray packaging option. The manufacturer product page and datasheet define the device, while distributor listings show commercial channels for the exact ordering code. Stock and lead time can change, so obtain a current quotation for the required quantity before committing the production schedule.

داتای سەرچاوەی ئەندازیاری بۆ LAN9352I/PT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LAN9352I/PT when an embedded product needs two managed 10/100 Ethernet ports, industrial-temperature capability, and compatibility with the established LAN9352 architecture. Its integrated PHYs, 1.2 V to 3.3 V supply range, and I2C or SPI host interfaces simplify the connection between an embedded processor and two network ports. Select LAN9352/PT when the industrial-temperature distinction is unnecessary and the standard-grade device is acceptable. Evaluate LAN9353T/PT only when its newer family features justify a controlled register-map, strap, and firmware migration. The 80-pin exposed-pad footprint makes all three candidates attractive for compact boards, but package similarity does not remove the need for pin-by-pin and software-level verification. For designs requiring more than two ports or speeds above 100 Mbps, a different Ethernet switch architecture is more appropriate.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LAN9352/PT LAN9353T/PT
Package 80-pin TQFP exposed-pad (12 x 12 mm) 80-pin TQFP exposed-pad (12 x 12 mm) 80-pin TQFP exposed-pad (12 x 12 mm)
Brand Microchip Technology Microchip Technology Microchip Technology
Ethernet Port Count 2 ports 2 ports 2 ports
Supported Speed 10 Mbps to 100 Mbps per port 10 Mbps to 100 Mbps per port 10 Mbps to 100 Mbps per port
Management Architecture Managed 2-port Ethernet switch Managed 2-port Ethernet switch Managed 2-port Ethernet switch

جیاکەرەوە سەرەکییەکان

  • Industrial-temperature ordering option (بەراورد بەLAN9352/PT)
  • Two integrated PHYs with managed host control (بەراورد بەLAN9353T/PT)
  • Established LAN9352 software family (بەراورد بەLAN9353T/PT)

تێبینییەکانی دیزاین

Implement the exposed pad as a thermal and electrical land pattern specified by the manufacturer. Connect it to the intended ground reference with multiple thermal vias and avoid placing high-current or high-temperature components immediately below the pad. The 80-pin TQFP exposed-pad construction provides a heat path, but adequate copper area, via count, and airflow determine whether that path remains effective at the system’s actual dissipation level.

Place Ethernet magnetic components, termination networks, and PHY-side connection points close to the LAN9352I/PT and route differential pairs as short, continuous pairs away from switching nodes and high-current paths. Keep the two PHY sections physically distinct to reduce unintended coupling. Follow the manufacturer’s reference layout for component order, grounding, and trace geometry rather than treating the package as a generic digital controller.

Separate the 1.2 V to 3.3 V supply rails according to the manufacturer’s internal rail requirements and connect only the permitted voltage domains to each power pin. Place required bypass capacitors at their designated pins with short ground returns, and control supply noise from the system’s switching converters. Review power-up, power-down, and host-interface sequencing because an incorrectly ordered rail can leave management registers inaccessible.

Do not assume that a shared 80-pin package proves drop-in compatibility. Compare pin names, exposed-pad treatment, strap inputs, host interface mode, power rails, management registers, and clock or interrupt behavior between the original and replacement device. A successful PCB fit can still produce a nonfunctional board if software expects different register addresses or startup defaults.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Use the current manufacturer product page and material-declaration documentation for environmental, quality, and regulatory status.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LAN9352I/PT datasheet LAN9352I/PT pinout LAN9352I/PT datasheet pdf LAN9352I/PT specifications LAN9352I/PT equivalent LAN9352I/PT replacement LAN9352I/PT cross reference LAN9352I/PT vs LAN9353T/PT LAN9352I/PT 80 pin TQFP LAN9352I/PT 10/100 Ethernet switch LAN9352I/PT I2C SPI interface Microchip LAN9352I/PT LAN9352I/PT industrial controller LAN9352I/PT price LAN9352I/PT stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology LAN9352I/PT LAN9352/PT LAN9353T/PT managed Ethernet switch Ethernet controller Ethernet switch ASIC network interface controller NIC 10BASE-T 100BASE-TX integrated PHY I2C SPI SQI IEEE 802.3 IEEE 802.3u 80-pin TQFP exposed-pad package surface-mount package SMD industrial automation embedded networking thermal via 1.2 V power rail 3.3 V power rail
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ