LAN9352T/PT - 2-Port 10/100 Managed Ethernet Switch | Microchip Technology
MPN: LAN9352T/PT ✓ چالاکLAN9352T/PT گشتی
A managed Ethernet switch is an interface IC that coordinates traffic between a host processor and multiple Ethernet ports. It can provide per-port configuration, status monitoring, link detection, and controlled frame forwarding, while the integrated PHYs reduce the external magnetic-component count compared with a discrete Ethernet design. LAN9352T/PT is positioned for compact embedded systems where two 10/100 ports provide a practical balance of connectivity, size, and functionality.
The device supports 10/100 Base-T/TX Ethernet operation and offers I2C and SPI host interfaces for configuration and control. The manufacturer describes LAN9352 as a high-performance, small-footprint, fully featured 2-port managed Ethernet switch optimized for consumer, embedded, and industrial designs. Its integrated architecture can shorten PCB routing and reduce component count compared with using separate Ethernet switch and PHY devices.
Because this orderable suffix identifies an 80-lead TQFP-EP package with gull-wing leads, the component is intended for surface-mount PCB assembly. The exposed-pad construction provides a thermal path from the die to the board copper, but layout should preserve the manufacturer-recommended land pattern and thermal-via arrangement. Confirm the exact pin functions, recommended external components, and exposed-pad connection in the manufacturer datasheet before finalizing a new layout.
Typical uses include industrial Ethernet gateways, embedded control systems, set-top equipment, print servers, network-connected test instruments, and compact embedded platforms that need two Fast Ethernet ports behind a serial host interface. The LAN9352T/PT is especially useful when the design benefits from integrated PHYs and local switch management without allocating a separate PHY for each port.
For a robust implementation, route each Ethernet differential pair as a controlled-impedance transmission line, use the prescribed magnetics and line-side components, place high-frequency bypass capacitance close to the supply pins, and connect the exposed thermal pad to the recommended ground-plane structure. Review clock, reset, and power sequencing requirements in the manufacturer datasheet. This page combines package, interface, sourcing, replacement, and design guidance to support initial component selection and PCB planning.
جێگرەوەکانی جێگۆڕکێ بۆ LAN9352T/PT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LAN9352T/PT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Ethernet Speed, Host Interface.
LAN9353T/PT
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LAN9352T/PT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 2-port managed Fast Ethernet switch |
| Number of Ethernet Ports | 2 ports |
| Ethernet Speed | 10/100 Base-T/TX |
| Integrated PHY Count | 2 integrated 10/100 PHYs |
| Host Interface | I2C and SPI |
| Management Architecture | Managed 2-port Ethernet switch |
| پاکێج | 80-lead TQFP-EP, 12 mm x 12 mm |
| Terminal Count | 80 terminals |
| جۆری دامەزراندن | Surface mount |
| Lead Form | Gull wing |
| Package Shape | Square |
| Package Code | HTFQFP |
| Temperature Grade | Commercial |
| Target Applications | Consumer, embedded, and industrial designs |
ڕێنمایی ڕێکخستنی پینی LAN9352T/PT htfqfp
ڕێکخستنی پین بۆ LAN9352T/PT (پاکێجی htfqfp). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LAN9352T/PT.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LAN9352T/PT گونجاوە بۆ 6 بەکارھێنانs: Industrial Ethernet Gateway, Embedded Network Control Platform, Network-Connected Test Instrument, Print Server and Network Peripheral, Set-Top and Connected Consumer Equipment, IoT Edge Gateway.
Industrial Ethernet Gateway
The LAN9352T/PT fits an industrial gateway that needs two local 10/100 Ethernet connections and serial host control. Its two integrated PHYs reduce the number of separate network interface components, while I2C and SPI access supports configuration, status monitoring, and port management by an embedded controller. The 80-lead TQFP-EP package supports compact surface-mount assembly but requires careful differential-pair routing and thermal-pad implementation. Before layout release, confirm the selected switch variant, Ethernet magnetics, isolation strategy, commercial temperature limits, and the exact manufacturer recommended component arrangement. This approach is especially useful when the gateway must bridge a local host processor to upstream and downstream Ethernet equipment without adding separate PHY packages.
پێشنیارکراو
Embedded Network Control Platform
The LAN9352T/PT is appropriate for an embedded control platform that connects a processor to two Fast Ethernet networks while keeping the PCB compact. The integrated 10/100 PHYs and managed-switch architecture can consolidate physical-layer and switching functions in one 80-lead TQFP-EP device. I2C or SPI provides a straightforward host-control path for configuring the device and reading link or port status. Because managed behavior and register definitions must match the host firmware, use the manufacturer datasheet for register maps, initialization, clocks, interrupts, and reset timing. PCB implementation should use the reference layout, short Ethernet traces, continuous reference planes, and a properly stitched exposed thermal pad.
پێشنیارکراو
Network-Connected Test Instrument
The LAN9352T/PT can support a test instrument with one management connection and one service or fixture connection, both operating at 10/100 Mb/s. A managed two-port device allows the host to control link behavior and monitor port status over I2C or SPI rather than relying on an external network controller. The integrated-PHY architecture can simplify board partitioning in compact laboratory equipment. Design engineers should verify magnetics selection, isolation requirements, cable-side component values, and the exact timing requirements of the test interface. Thermal management also matters because the exposed-pad TQFP construction depends on good PCB copper and via placement to remove heat efficiently without disrupting Ethernet return paths.
پێشنیارکراو
Print Server and Network Peripheral
The LAN9352T/PT is a practical fit for a print server or network peripheral that needs two Fast Ethernet ports for host connectivity and an upstream network link. Its integrated 10/100 PHYs reduce PCB area, and managed switching provides a local option for port configuration and status monitoring. A serial interface allows a low-cost embedded controller to initialize the network device without a dedicated network processor. For deployment, validate the magnetic-component and line-side network design against the manufacturer reference circuit, and confirm that the chosen magnetics support the intended isolation, distance, and regulatory environment. Firmware should also implement link handling, startup delays, and recovery behavior for disconnected cables.
پێشنیارکراو
Set-Top and Connected Consumer Equipment
The LAN9352T/PT supports set-top boxes, media devices, and connected consumer products that need two 10/100 Ethernet connections in a small-footprint design. Its fully featured managed-switch positioning provides more control than a basic unmanaged PHY while retaining integration suitable for cost-sensitive embedded products. I2C and SPI interfaces allow the host processor to manage initialization, status, and port behavior. Layout must preserve the 12 mm by 12 mm 80-lead TQFP-EP land pattern and use the manufacturer’s recommended magnetics and bypass network. Thermal via placement and exposed-pad grounding are critical because the compact package concentrates heat directly beneath the die.
پێشنیارکراو
IoT Edge Gateway
The LAN9352T/PT can form the wired networking section of an IoT edge gateway by providing two managed 10/100 ports alongside a host processor. The first port can connect an upstream network while the second supports a downstream controller or service device, and integrated PHYs simplify enclosure-space and PCB-area allocation. Management access through I2C or SPI allows software to monitor link conditions and manage traffic at the edge. For production, validate the exact operating-temperature requirement, Ethernet isolation and surge strategy, and regulatory approvals of the complete product rather than the IC alone. Follow the manufacturer layout for magnetics spacing, differential impedance, power sequencing, and exposed-pad thermal relief.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LAN9352T/PT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LAN9353T/PT |
|---|---|---|
| Package | 80-lead TQFP-EP, 12 mm x 12 mm | 80-lead TQFP-EP, 12 mm x 12 mm |
| Brand | Microchip Technology | Microchip Technology |
| Mounting Type | Surface mount | Surface mount |
| Pin Count | 80 terminals | 80 terminals |
جیاکەرەوە سەرەکییەکان
- Integrated managed switching and two PHYs in one package (بەراورد بەLAN9353T/PT)
- Compact 12 mm by 12 mm surface-mount implementation (بەراورد بەLAN9353T/PT)
- Serial host-control flexibility (بەراورد بەLAN9353T/PT)
تێبینییەکانی دیزاین
Implement the Ethernet section from the manufacturer reference layout, preserving controlled-impedance differential routing, uninterrupted reference planes, and the recommended spacing between the integrated PHY, magnetics, and line-side components. Avoid adding test pads, vias, or plane discontinuities beneath the differential pairs unless the manufacturer guidance permits them. Keep the two port groups separated according to the reference design to limit crosstalk and simplify troubleshooting.
The 80-lead TQFP-EP uses its exposed pad as a thermal and electrical land. Follow the manufacturer land-pattern dimensions and thermal-via arrangement rather than substituting a generic exposed-pad footprint. Preserve as much uninterrupted ground copper as practical beneath the device, avoid thermal relief breaks that impede heat flow, and use the exposed-pad connection specified in the datasheet. Confirm the finished-board thermal performance during worst-case ambient and sustained-link testing.
Place all prescribed bypass capacitors close to their corresponding supply pins and keep the supply paths short. Follow the manufacturer’s required power-up, power-down, reset, and clock sequencing before configuring the PHY and switch registers. Decoupling values should match the datasheet reference circuit; blindly adding large bulk capacitance can alter supply ramp behavior or increase inrush current.
Do not treat a shared package size as proof that a replacement is pin-compatible. For any substitute, compare every power and ground connection, Ethernet differential mapping, host interface, management signal, clock, reset, exposed pad, absolute maximum rating, and initialization sequence. Also verify magnetic-component requirements and software driver support. A board-level functional test should cover cold start, link insertion, unplug events, sustained traffic, and recovery from partial power loss.
زانیاری پابەندبوون
The device is identified as commercial grade and intended for consumer, embedded, and industrial designs. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations must be confirmed from the current Microchip material documentation for the exact orderable suffix.