LFE2-12E-6F256I - 12K LUT 256-BGA FPGA | Lattice
MPN: LFE2-12E-6F256I ✓ چالاکLFE2-12E-6F256I گشتی
An FPGA is a programmable semiconductor containing configurable logic, routing, and input/output resources. Rather than implementing a fixed digital function in silicon, an FPGA can be reconfigured after manufacture to perform control logic, protocol conversion, data acquisition, signal conditioning, or system interfacing. The LFE2-12E-6F256I belongs to the LatticeECP2 family, where the E identifies the device family, 12 denotes the approximate logic-cell capacity, 6 identifies the speed grade, F256 indicates the 256-ball package, and I identifies the industrial temperature option.
The principal device characteristics include 12,000 LUTs, 193 I/O, and 1.2 V operation according to the Lattice product listings. A comparison source identifies the ECP2 implementation as a 90 nm FPGA with approximately 311 MHz device performance. These resources make the device suitable for designs requiring substantially more programmable logic than a small CPLD while retaining the relatively compact 256-ball package used for high-pin-count mixed-signal and embedded systems.
Typical designs include industrial control and factory automation, data-acquisition front ends, communications-interface bridges, embedded instrumentation, and general-purpose digital signal conditioning. The 193 available I/O positions support parallel sensor, actuator, memory, and communication interfaces. Designers should also account for the FBGA package's thermal and assembly requirements, including PCB escape routing, via-in-pad or through-via fanout, adequate ground distribution, and controlled reflow profiles.
For replacement planning, the device should be matched on more than capacity: logic-cell count, I/O availability, package ballout, speed grade, temperature grade, supported clocking, memory interfaces, and configuration method must remain compatible. The manufacturer documentation should be checked before treating an ECP2 ordering code as a drop-in replacement. Configuration flash, pull-up or pull-down requirements, bank voltages, and JTAG or configuration pins also affect board-level interchangeability.
This page consolidates the exact ordering information, package details, candidate replacements, comparison parameters, and practical FPGA design guidance needed to evaluate the LFE2-12E-6F256I for new and existing PCB designs.
جێگرەوەکانی جێگۆڕکێ بۆ LFE2-12E-6F256I — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LFE2-12E-6F256I (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە FPGA Family, Package Type, Speed Grade.
LFE2-12E-6FN256I
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LFE2-12E-5FN256I
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LFE2-12SE-6FN256I
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LFE2-12SE-5FN256C
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LFE2-12SE-5F256I
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LFE2-12E-6F256I زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Device Type | Field Programmable Gate Array (FPGA) |
| FPGA Family | LatticeECP2 |
| Logic Cells | 12,000 cells |
| Equivalent LUT Count | 12K LUTs |
| I/O Count | 193 I/O |
| Core Voltage | 1.2 V |
| Speed Grade | -6 |
| Device Technology | 90 nm |
| Maximum Device Frequency | 311 MHz |
| پاکێج | 256-BGA |
| Package Type | FPBGA-256 |
| Package Dimensions | 17 mm x 17 mm |
| Temperature Grade | Industrial |
| Lead-Free Status | Lead free |
| DSP Multiplier Count | 1 DSP |
ڕێنمایی ڕێکخستنی پینی LFE2-12E-6F256I 17 mm x 17 mm
ڕێکخستنی پین بۆ LFE2-12E-6F256I (پاکێجی 17 mm x 17 mm). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LFE2-12E-6F256I.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LFE2-12E-6F256I گونجاوە بۆ 6 بەکارھێنانs: Industrial Control and Automation, Data Acquisition and Signal Conditioning, Communications Interface Bridging, Test and Measurement Instrumentation, Embedded Interface Consolidation, Video and Display Control.
Industrial Control and Automation
The LFE2-12E-6F256I fits industrial controllers that combine parallel I/O, sequencing logic, and configurable interface behavior. Its 12,000 logic cells provide room for control-state machines, counters, timing blocks, and diagnostic logic, while 193 I/O provide connections to sensors, actuators, encoders, and discrete industrial interfaces. The 1.2 V core and -6 speed grade support compact control designs that benefit from higher performance than the -5 alternatives. Place the FPBGA-256 device with a continuous ground plane and carefully routed power distribution to preserve signal integrity around dense external interfaces.
پێشنیارکراو
Data Acquisition and Signal Conditioning
The LFE2-12E-6F256I is suitable for parallel data-acquisition front ends that must combine sampling control, digital filtering, thresholding, and data formatting in one programmable device. Twelve thousand logic cells and 193 I/O allow multiple converter data buses, capture registers, and communication outputs to be integrated without relying on several fixed-function controllers. Its approximately 311 MHz listed device performance provides useful timing headroom for parallel pipelines. The principal design consideration is I/O-bank voltage compatibility with external converters, which must be verified against the manufacturer electrical tables before assigning pins.
پێشنیارکراو
Communications Interface Bridging
The LFE2-12E-6F256I can implement protocol converters, parallel-to-serial interfaces, test instrumentation links, and embedded communications bridges in programmable logic. Its 12K-LUT capacity is appropriate for multiple finite-state machines, FIFOs, and clock-domain crossings, while 193 I/O supports parallel buses commonly used by memory, microcontroller, and legacy peripheral devices. Compared with the -5 ECP2 options, the -6 grade offers additional timing margin for synchronous interfaces. Engineers should still constrain clock routing and use the manufacturer's recommended I/O standards to minimize skew and ringing.
پێشنیارکراو
Test and Measurement Instrumentation
The LFE2-12E-6F256I is well suited to programmable test systems that coordinate stimulus, capture, timing, and result formatting across many parallel channels. Its 193 I/O can support instrument control registers, trigger distribution, status capture, and operator-panel logic, while 12,000 logic cells allow reusable timing engines and digital analysis functions. The -6 speed grade and listed 311 MHz performance provide a useful margin for synchronous test sequences. Board design must preserve clock and data timing across the FBGA package, and unused balls should follow the manufacturer's grounding or no-connect guidance.
پێشنیارکراو
Embedded Interface Consolidation
The LFE2-12E-6F256I can consolidate fixed logic previously distributed across multiple glue devices by implementing decoders, address mapping, interrupt control, and peripheral emulation. With 12,000 logic cells and 193 I/O, it fits compact systems requiring numerous parallel pins but modest external memory requirements. The 1.2 V core reduces supply complexity in modern mixed-signal equipment, although its FPBGA-256 footprint demands careful escape routing and a stable thermal design. Designers should compare the E configuration with SE alternatives because the system features and configuration options may differ despite the shared package.
پێشنیارکراو
Video and Display Control
The LFE2-12E-6F256I can support timing generation, display sequencing, pixel-stream control, and auxiliary interface logic in embedded video equipment. Its 12K-LUT capacity is sufficient for moderate timing pipelines and control state machines, while 193 I/O offers access to parallel timing, control, and data signals. The -6 speed grade provides additional timing margin relative to -5 alternatives, making it useful where display timing margins are tight. Practical designs should minimize fanout on clock nets, account for FBGA escape-routing delays, and verify that every connected transceiver and panel interface uses compatible I/O voltage standards.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LFE2-12E-6F256I — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LFE2-12E-6FN256I | LFE2-12E-5FN256I | LFE2-12SE-6FN256I | LFE2-12SE-5FN256C | LFE2-12SE-5F256I |
|---|---|---|---|---|---|---|
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| FPGA Family | LatticeECP2 | LatticeECP2 | LatticeECP2 | LatticeECP2 | LatticeECP2 | LatticeECP2 |
| Logic Cells | 12,000 cells | 12,000 cells | 12,000 cells | 12,000 cells | 12,000 cells | 1,500 LABs |
| Core Voltage | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V | 1.2 V |
| Speed Grade | -6 | -6 | -5 | -6 | -5 | -5 |
| Process Technology | 90 nm | 90 nm | 90 nm | 90 nm | 90 nm | 90 nm |
| Device Configuration Family | E | E | E | SE | SE | SE |
| Temperature Designation | Industrial | Industrial | Industrial | Industrial | Commercial | Industrial |
جیاکەرەوە سەرەکییەکان
- Higher -6 speed grade than the -5 ECP2 candidates (بەراورد بەLFE2-12E-5FN256I)
- Active ordering option versus an obsolete close comparison (بەراورد بەLFE2-12E-6FN256I)
- E configuration supports the same nominal ECP2 resource class as SE alternatives (بەراورد بەLFE2-12SE-6FN256I)
- Full 193-I/O offering within the same 12K ECP2 class (بەراورد بەLFE2-12SE-5FN256C)
تێبینییەکانی دیزاین
Treat the FPBGA-256 layout as a high-density escape-routing problem. Place the FPGA in accordance with the manufacturer package drawing, provide clean power and ground planes, and route high-speed clocks through short, symmetric paths. Confirm via dimensions, solder-mask clearance, and assembly-process requirements with the PCB fabricator before layout release.
Design the 1.2 V core rail with decoupling and distribution that comply with the manufacturer power-supply recommendations. Account for normal and worst-case I/O activity because bank current can vary with switching. Keep sensitive input references away from high-current outputs and provide adequate return paths for every supply connection.
Use the manufacturer's recommended I/O standards and drive-strength settings for external buses and clocks. Avoid long stubs from the FPGA, constrain clock and data paths, and maintain suitable spacing between high-speed nets and sensitive inputs. The 193 I/O count offers flexibility, but it does not eliminate pin-capacitance and timing constraints.
Estimate junction temperature from actual package dissipation, ambient temperature, and the board-specific junction-to-ambient thermal resistance rather than using a generic PCB value. The 17 mm by 17 mm FBGA offers substantial connectivity but requires uninterrupted thermal-via distribution beneath and around the device. Re-evaluate thermal margin when adjacent devices dissipate significant power.
Do not treat matching ECP2 capacity and package dimensions as proof of drop-in interchangeability. Before substituting an LFE2-12E, LFE2-12SE, speed-grade, or temperature-ordering variant, verify exact ball assignments, supported configuration methods, power-up behavior, I/O-bank restrictions, exposed-pad requirements, timing margins, and lifecycle status.
زانیاری پابەندبوون
The comparison data identifies the LFE2-12E-6F256I as lead free. RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals declarations are not established by the cited records.