Diodes Incorporated

LM2903AQS-13 - Dual 36V AEC-Q100 Comparator | Diodes Inc

MPN: LM2903AQS-13 ✓ چالاک
2 V to 36 V Vdss 25 nA Id 8-SOIC (SO-8) Package
MOQ: 1 |

LM2903AQS-13 گشتی

The Diodes Incorporated LM2903AQS-13 is an automotive-grade dual differential voltage comparator with a wide supply range of 2V to 36V on a single supply (or ±1V to ±18V on dual supplies), a typical input offset voltage of 1mV, and open-collector outputs in an 8-pin SOIC (SO-8) package qualified to AEC-Q100.

A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which is higher. Within the power-management and signal-conditioning hierarchy, comparators sit alongside operational amplifiers and voltage references; unlike an op-amp, a comparator is intentionally uncompensated for fastest switching and is used with an open-collector output stage to interface directly with TTL and CMOS logic.

Key features of the LM2903AQS-13 include very low input offset voltage (1mV typical), low input bias current of 25nA, and low supply current drain of approximately 0.6mA per comparator, which makes the device suitable for battery-powered designs. The common-mode input voltage range includes ground even when operated from a single supply, allowing the part to sense signals near 0V without an external negative rail.

The device belongs to the industry-standard LM2901Q/LM2903Q family from Diodes Incorporated. Outputs are open-collector, so pull-up resistors are required and multiple outputs can be wired-OR for window-comparator or over-voltage/under-voltage detection topologies. Rail-to-rail output swing to the positive rail is achieved through the external pull-up, and the output stage sinks current to ground with saturation voltage low enough to drive TTL logic directly.

Typical applications include automotive sensor monitoring and limit detection, over-voltage and under-voltage supervisors, window comparators on industrial 24V-rail systems, oscillator and Schmitt-trigger circuits, and battery-management threshold detection in portable equipment. The automotive qualification (AEC-Q100) makes it especially appropriate for in-vehicle modules exposed to -40C to +125C ambient conditions.

When designing with this part, remember that the open-collector output requires a pull-up resistor; the pull-up may be referenced to any voltage up to the 36V absolute maximum regardless of the comparator supply. Input common-mode range must be respected at the negative extreme, and hysteresis (a few millivolts via positive feedback) should be added when comparing slowly moving signals to prevent output chatter.

This page synthesizes distributor inventory listings, drop-in cross-reference data, and practical design notes not found in the manufacturer datasheet, providing a single quotable reference for sourcing and design engineers.

جێگرەوەکانی جێگۆڕکێ بۆ LM2903AQS-13 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903AQS-13 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Output Type, Comparator Type, Package, Common-Mode Input Range, Input Bias Current.

Diodes Incorporated
Output Type: Open-collector
Comparator Type: Dual precision voltage comparator
Package: 8-pin SOIC
بەراوردکردن لەگەڵ LM2903AQS-13 →
Texas Instruments
Output Type: Open-collector/open-drain
Comparator Type: Dual differential comparator
Common-Mode Input Range: Includes ground
بەراوردکردن لەگەڵ LM2903AQS-13 →
onsemi
Output Type: Open collector
Comparator Type: Dual differential comparator
Package: 8-SOIC
بەراوردکردن لەگەڵ LM2903AQS-13 →

LM2903QS-13

✅ جێگرەوەی ڕاستەوخۆ
Diodes Incorporated
📦 SOIC-8
Dual precision voltage comparator · 2 channels · 36 V · ±18 V · 2 mV · 25 nA · 5 nA · 0.6 mA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903AQS-13

✅ جێگرەوەی ڕاستەوخۆ
Diodes Incorporated
📦 SOIC-8
2 (dual) · General purpose, differential · Open-collector, rail-to-rail (with pull-up) · 2 V to 36 V · ±1 V to ±18 V · 1 mV (typical) · 25 nA · 0.6 mA (typical)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903AQDRQ1

✅ جێگرەوەی ڕاستەوخۆ
📦 SOIC-8
TI automotive-grade dual comparator, pin-for-pin per TI cross-reference page, same 36V open-collector operation

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM293AD

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential comparator · 2 channels · 2 V to 36 V · -38 V to +38 V · Includes ground · Rail-to-rail · Open-collector/open-drain · 300 ns

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393AM

✅ جێگرەوەی ڕاستەوخۆ
onsemi
📦 SOIC-8
Dual differential comparator · 2 channels · 36 V maximum · ±18 V maximum · 800 µA typical · 25 nA typical · Open collector · Compatible with all forms of logic

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903AQS-13 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Comparators 2 (dual)
Comparator Type General purpose, differential
جۆری دەرچوون Open-collector, rail-to-rail (with pull-up)
Supply Voltage Range (Single) 2 V to 36 V
Supply Voltage Range (Dual) ±1 V to ±18 V
Input Offset Voltage 1 mV (typical)
Input Bias Current 25 nA
ئێستای دابینکردن 0.6 mA (typical)
Common-Mode Input Range Includes ground (single supply)
Logic Interface TTL and CMOS compatible output
Automotive Qualification AEC-Q100 qualified
پلەی گەرمیی کارکردن -40C to +125C
پاکێج 8-SOIC (SO-8)
جۆری دامەزراندن Surface Mount
ئاستی MSL MSL 1
دۆخی RoHS Compliant (RoHS Y)

ڕێکخستنی پینی LM2903AQS-13

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT A — Output A (open collector, requires pull-up)
پین 2 IN A- — Inverting input, comparator A
پین 3 IN A+ — Non-inverting input, comparator A
پین 4 GND (V-) — Ground / negative supply
پین 5 IN B+ — Non-inverting input, comparator B
پین 6 IN B- — Inverting input, comparator B
پین 7 OUT B — Output B (open collector, requires pull-up)
پین 8 VCC (V+) — Positive supply, 2V to 36V

بەکارهێنانە باوەکان

LM2903AQS-13 گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Monitoring, Over-Voltage / Under-Voltage Supervision, Window Comparators, Oscillators and Schmitt Triggers, Battery Management Threshold Detection, Industrial 24V Rail Fault Detection.

🚗

Automotive Sensor Monitoring

In automotive modules, sensors such as pressure, level, and position transducers produce analog signals that must be checked against upper and lower limits before the ECU acts on them. The LM2903AQS-13 fits this role because it is AEC-Q100 qualified from -40C to +125C, so it survives under-hood and cabin temperature cycles without derating. Its 2V to 36V single-supply range covers 12V automotive boards directly, and the common-mode input range including ground lets it sense sensors that pull down near 0V. Each of the two comparators can monitor one limit of a sensor window, with open-collector outputs wire-ORed into a single fault line. Add a few millivolts of positive-feedback hysteresis so slow sensor ramps do not chatter the output, and use 1% tolerance divider resistors so the 1mV typical offset does not dominate trip-point accuracy.

⚡

Over-Voltage / Under-Voltage Supervision

Power-rail supervisors need comparators that tolerate rail transients while holding accurate trip thresholds. The LM2903AQS-13's 36V maximum supply gives 12V and 24V systems generous headroom above nominal, and its open-collector output can pull up to a logic rail or the monitored rail independently of the comparator supply, simplifying level interfacing to a microcontroller fault input. Both comparators in the single SO-8 package monitor over-voltage and under-voltage simultaneously, wired-OR into one RESET fault line. The 25nA input bias current keeps divider current low, so a high-impedance sense network saves power in always-on supervision circuits. Design the trip points with 1% resistors and reference the thresholds to a TL431 or bandgap reference; the 1mV typical offset of the A-grade contributes negligible error compared with divider tolerance.

🔧

Window Comparators

A window comparator flags when a signal leaves a defined band, using one comparator for the upper limit and one for the lower limit - exactly the two-comparator count the LM2903AQS-13 provides in one package. Because the outputs are open-collector, tying them together forms the wire-OR window output with no extra logic gate. The ground-including common-mode range allows windows defined near 0V, and the 36V supply supports window monitoring on high-voltage industrial buses and solar strings. The 1mV typical offset of the A-grade lets designers set narrow windows (tens of millivolts) without the comparator itself dominating the error budget. Use independent hysteresis resistors on each half so both edges have clean switching, and keep the feedback paths separate to avoid interaction between the two thresholds.

🔧

Oscillators and Schmitt Triggers

Comparators with modest propagation delay make excellent relaxation oscillators and Schmitt triggers for clock generation, watchdog timing, and switch debouncing. The LM2903AQS-13's uncompensated comparator stage switches faster than a general-purpose op-amp in the same role, and its low 0.6mA supply current suits battery-powered timers that run continuously. Configuring positive feedback around one comparator creates hysteresis for a clean Schmitt trigger; configuring an RC timing network plus feedback creates a square-wave oscillator whose frequency is set by the RC product. Because the output is open-collector, the pull-up resistor can reference a 3.3V or 5V logic rail even when the timing network runs on the full 2V to 36V supply, giving direct TTL and CMOS compatibility noted in the family datasheet.

🔋

Battery Management Threshold Detection

Battery-powered systems continuously compare cell or pack voltage against charge and discharge cutoff thresholds. The LM2903AQS-13 operates down to 2V, so it remains functional even as a discharged cell collapses, allowing an undervoltage comparator to fire near the end of discharge - the condition where a higher-minimum-supply comparator would already be dead. Its 0.6mA typical supply current plus 25nA bias current keeps the monitor's contribution to quiescent drain small enough for portable designs. The common-mode range including ground permits direct sensing of low cell voltages, and the AEC-Q100 qualification extends use to battery packs in e-mobility and power-tool products. Open-collector outputs wire-OR easily into a single enable/disable line driving the charge controller.

🏭

Industrial 24V Rail Fault Detection

Industrial control cabinets run on 24V buses where fuses, sensors, and actuators must be supervised for open-circuit and short-circuit faults. The LM2903AQS-13's 36V supply rating covers 24V rails plus transient margin, and its -40C to +125C operating range suits unconditioned cabinet environments. Each comparator monitors one fault line from a resistor divider or current-sense shunt, and the open-collector outputs combine into a shared fault bus read by the PLC or microcontroller. The ground-including common-mode range senses signals referenced to chassis ground directly. Because the AEC-Q100 qualification exceeds typical industrial screening, the part provides reliability margin in factory-floor conditions at commodity cost. Add hysteresis and RC filtering so motor-switching transients do not generate false fault pulses.

What is the supply voltage range of LM2903AQS-13?
The LM2903AQS-13 operates from 2V to 36V on a single supply, or from ±1V to ±18V on split supplies. According to the Diodes Incorporated LM2903AQ family datasheet, this wide range allows direct connection to automotive 12V and industrial 24V rails (with headroom), while the 2V minimum supports low-voltage battery systems. The common-mode input range includes ground even in single-supply operation, so signals near 0V can be sensed without a negative rail.
What is the input offset voltage of LM2903AQS-13?
The LM2903AQS-13 has a typical input offset voltage of 1mV. According to the Mouser listing for the part, the device is characterized as a 36V dual comparator with 25nA input bias current and 1mV offset. Low offset means small input differentials are resolved accurately, which matters in threshold-detection and battery-monitor circuits where the trip point may be only tens of millivolts above the reference.
Does LM2903AQS-13 have open-collector outputs?
Yes, the LM2903AQS-13 has open-collector outputs. Per the DigiKey product page, the device is a standard general-purpose comparator with open-collector, rail-to-rail output capability. Each output needs an external pull-up resistor, which may reference any voltage up to 36V independent of the comparator supply. Open-collector outputs also allow wire-OR connections of multiple comparators for window-comparator and multi-level supervisor topologies.
Is LM2903AQS-13 automotive qualified?
Yes, the LM2903AQS-13 is an automotive-grade part qualified to AEC-Q100. According to GlobalSpec's datasheet summary, the dual differential comparator is designed for automotive applications and compliant with AEC-Q100, operating from -40C to +125C. The 'Q' suffix in the family name (LM2903AQ) denotes this qualification, making the part suitable for in-vehicle sensor monitoring, power-rail supervision, and other modules subject to automotive temperature and reliability requirements.
What is the difference between LM2903AQS-13 and LM2903QS-13?
The LM2903AQS-13 is the enhanced 'A' grade of the LM2903Q family, offering tighter input offset voltage specifications, while LM2903QS-13 is the base automotive-grade version. According to the Diodes Incorporated LM2901Q/LM2903AQ datasheet, both parts are pin-for-pin identical in SO-8, MSOP-8 and TSSOP-8 packages with the same 2V to 36V supply range, so LM2903QS-13 can replace LM2903AQS-13 where the tighter offset accuracy of the A-grade is not required.
What is the best drop-in replacement for LM2903AQS-13?
The best same-brand drop-in replacement is the Diodes Incorporated LM2903QS-13 (base AEC-Q100 grade, same SO-8 pinout). Cross-brand, the Texas Instruments LM2903AQDRQ1 is pin-for-pin compatible in SO-8 with the same 36V rating and open-collector outputs; TI's product page explicitly lists the LM2903 family as pin-for-pin drop-in compatible with the compared device. Any substitution should be verified against the SO-8 pin description table in the respective datasheets before layout release.
What is the best TI equivalent for LM2903AQS-13?
The best Texas Instruments equivalent is the LM2903AQDRQ1, the automotive-qualified dual comparator in SO-8. According to TI's LM2903 product page, the family is offered as pin-for-pin with the same functionality as compared devices, and the LM2901Q/LM2903AQ family from Diodes was designed in the industry-standard pinout shared with TI's parts. Both operate from 2V to 36V with open-collector outputs, so PCB footprint and circuit topology carry over unchanged.
LM2903AQS-13 vs LM393AM - which is better for automotive designs?
For automotive designs, the LM2903AQS-13 is the safer choice because it is explicitly AEC-Q100 qualified over -40C to +125C. The LM393AM compared on Utmel shares the same dual-comparator function and open-collector output in a similar package, but qualification grade and offset specifications differ between vendors' LM393 variants. If your design requires automotive PPAP documentation, use the LM2903AQS-13 or TI's LM2903AQDRQ1; for non-automotive consumer circuits, LM393 variants may suffice at lower cost.
When should I choose LM2903AQS-13 over a standard LM393 comparator?
Choose the LM2903AQS-13 when the design must meet automotive reliability requirements (AEC-Q100), when the ambient range extends to +125C, or when tighter input offset voltage (1mV typical on the A-grade) improves threshold accuracy. For non-critical consumer boards operating only from 0C to +70C, a standard LM393 achieves the same function at lower cost. The LM2903AQS-13 also suits 36V industrial rails, where the wide 2V to 36V supply range and ground-including common-mode range simplify level sensing.
Is LM2903AQS-13 suitable for a 24V industrial rail supervisor?
Yes, the LM2903AQS-13 is well suited to 24V rail supervision because its supply range extends to 36V, providing ample headroom above a nominal 24V rail with transients. According to the Diodes Incorporated family datasheet, the device operates from 2V to 36V single-supply, and its open-collector output can pull up to a logic rail while the inputs monitor a resistor divider on the 24V bus. Add positive-feedback hysteresis of a few millivolts to prevent chatter near the trip point.
Where can I download the LM2903AQS-13 datasheet PDF?
The LM2903AQS-13 datasheet PDF is available for download from the Diodes Incorporated website at diodes.com/datasheet/download/LM2903AQ.pdf, which covers the LM2901Q/LM2901AQ/LM2903Q/LM2903AQ family including the A-grade variants. Mirror copies are hosted on datasheet aggregators such as Alldatasheet and Octopart, but the manufacturer PDF is the authoritative source for absolute maximum ratings, electrical characteristics tables, and the SO-8 pin configuration diagram.
Where can I find the LM2903AQS-13 pinout?
The LM2903AQS-13 pinout follows the industry-standard dual-comparator SO-8 assignment: pin 1 is OUT A, pin 2 is IN A- (inverting), pin 3 is IN A+ (non-inverting), pin 4 is GND/V-, pin 5 is IN B+ (non-inverting), pin 6 is IN B- (inverting), pin 7 is OUT B, and pin 8 is VCC/V+. The complete pin-description diagram is in the Diodes Incorporated LM2903AQ datasheet, and the pin-diagram asset on this page mirrors the same assignment.
What are the key specifications of LM2903AQS-13 that engineers should know?
The LM2903AQS-13 is a dual differential comparator in SO-8 with 2V to 36V single-supply (±1V to ±18V dual) operation, 1mV typical input offset, 25nA input bias current, about 0.6mA supply current, and open-collector TTL/CMOS-compatible outputs. It is AEC-Q100 qualified from -40C to +125C, MSL 1, and RoHS compliant. These specifications make it a low-power, wide-voltage, automotive-grade choice for threshold detection, supervision, and level sensing across automotive, industrial, and battery-powered systems.
What is the price of LM2903AQS-13 and how do I buy it?
The LM2903AQS-13 is a stockable catalog item carried by major distributors, with distributor listings such as LCSC showing availability of the part. For current unit pricing, quantity breaks, and lead time, submit the Request a Quote form on this page; XAIPART will respond with a formal quotation for your required quantity and packaging (this part ships in tape-and-reel for automated assembly). Inventory and pricing move daily, so a live quote is the most accurate source.
What can replace LM2903AQS-13 if it becomes unavailable?
If the LM2903AQS-13 becomes unavailable, first substitute the same-brand LM2903QS-13 (identical pinout and ratings, base accuracy grade), or the TI LM2903AQDRQ1, which is pin-for-pin compatible in SO-8 with 36V open-collector operation and AEC-Q100 qualification. The ST LM293AD also appears in published comparisons of this part. Before substitution, confirm the A-grade offset specification, temperature range, and the SO-8 pin description table in the replacement datasheet match your circuit requirements.

داتای سەرچاوەی ئەندازیاری بۆ LM2903AQS-13 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM2903AQS-13 when you need an automotive-qualified, wide-voltage (2V to 36V) dual comparator with accurate thresholds: it is the right pick for AEC-Q100 vehicle modules, 24V industrial supervisors, and battery monitors where the -40C to +125C range and 1mV typical offset matter. If your design is non-automotive and does not need the tighter A-grade offset, the same-brand LM2903QS-13 delivers identical pinout and ratings at lower cost. If your BOM standardizes on TI, the LM2903AQDRQ1 is pin-for-pin equivalent in SO-8 with the same qualification and voltage range, so it is a direct second source. The ST LM293AD serves industrial wide-temperature designs, while the LM393AM should be reserved for consumer-grade boards with restricted temperature ranges. All candidates share the industry-standard SO-8 dual-comparator pinout, so layout changes are not required when switching between them.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM2903QS-13 LM2903AQDRQ1 LM293AD LM393AM
Package SOIC-8 (SO-8) SOIC-8 - same SOIC-8 - same SOIC-8 - same SOIC-8 - same
Brand Diodes Incorporated Diodes Incorporated Texas Instruments STMicroelectronics STMicroelectronics
Supply Voltage Range 2V to 36V 2V to 36V 2V to 36V 2V to 36V 2V to 36V
Number of Comparators 2 2 2 2 2
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector

جیاکەرەوە سەرەکییەکان

  • A-grade 1mV typical input offset voltage (بەراورد بەLM2903QS-13)
  • AEC-Q100 qualification at commodity pricing (بەراورد بەLM393AM)
  • 36V supply headroom in SO-8 (بەراورد بەLM2903AQDRQ1)

تێبینییەکانی دیزاین

Pull-up resistor selection on the open-collector outputs is the single most important design decision. A 4.7k to 10k pull-up to the logic rail gives a good speed/power compromise: lower values speed the rising edge but increase current when the output is low. The pull-up may reference any voltage up to 36V regardless of the comparator supply, which allows level shifting between a 36V-monitored domain and 3.3V logic. Place the pull-up close to the output pin and keep the trace short to limit edge ringing.

Comparators switching at a slowly moving trip point will chatter unless hysteresis is added. Add positive feedback from output to the non-inverting input: a few millivolts of hysteresis (e.g., 1M feedback resistor around a 10k input divider gives roughly tens of millivolts) cleanly separates rising and falling thresholds. With 1mV typical input offset, A-grade accuracy is wasted if no hysteresis is used on noisy signals. Estimated: hysteresis width = pull-up voltage x (Rdiv/Rfb); verify with your actual resistor values.

Bypass VCC (pin 8) to GND with a 100nF ceramic capacitor placed within a few millimeters of the pin, especially when the comparator drives moderate capacitive loads through the pull-up. At only 0.6mA typical supply current per the family datasheet, self-heating is negligible, so no thermal consideration is needed for the SO-8 footprint; the part runs comfortably to +125C ambient per its AEC-Q100 rating. Do not exceed 36V supply - automotive load-dump transients on the monitored rail must be clamped upstream.

Do not use the LM2903AQS-13 as an op-amp: it is uncompensated and has no linear-region stability guarantee. Respect the common-mode input range - although it includes ground on single supply, inputs must stay within the datasheet limits even during faults, or parasitic paths through the input stage can upset the other comparator on the shared die. Unused comparator halves should have both inputs tied to a defined rail (e.g., inverting input to GND, non-inverting to VCC via a resistor) to prevent oscillation.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Qualified
بێ قوڕقوشم
Yes
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

RoHS compliant (RoHS Y) and MSL 1 per PartGenie listing for this part; AEC-Q100 qualified per GlobalSpec datasheet summary of the LM2901Q/LM2903Q automotive series.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM2903AQS-13 datasheet LM2903AQS-13 pinout LM2903AQS-13 datasheet pdf LM2903AQS-13 equivalent LM2903AQS-13 replacement LM2903AQS-13 vs LM393AM LM2903AQS-13 price Diodes Incorporated LM2903AQS-13 LM2903AQS-13 stock buy LM2903AQ SOIC-8 dual comparator pinout automotive dual comparator AEC-Q100 36V LM2903 application circuit window comparator

پێکهاتە و زاراوە پەیوەندیدارەکان

Diodes Incorporated LM2903AQS-13 LM2903QS-13 LM2903AQDRQ1 LM293AD LM393AM Texas Instruments STMicroelectronics dual differential voltage comparator comparator open-collector output AEC-Q100 RoHS SOIC-8 SO-8 surface mount input offset voltage input bias current window comparator Schmitt trigger automotive sensor monitoring over-voltage supervision battery management
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ