LM2903ITL/NOPB - Dual Open-Collector Comparator | Texas Instruments
MPN: LM2903ITL/NOPB ✓ چالاکLM2903ITL/NOPB گشتی
A dual differential comparator is a semiconductor that evaluates the relative voltages applied to its inverting and non-inverting inputs and changes its output state when the difference crosses a defined threshold. The LM2903 family contains two independent comparison channels in one package, allowing one device to monitor two signals. As an analog comparator, it belongs to the comparator hierarchy within interface and signal-conditioning semiconductors, where it converts an analog voltage relationship into a digital logic indication.
The open-collector output architecture permits the output stage to remain unpowered when a compatible pull-up network provides the desired logic voltage. This characteristic supports wired connections, interface standards, and system-level voltage-level compatibility. Rail-to-rail input behavior allows the comparison inputs to operate across the device supply range, which is useful when sensing signals near either supply rail.
The LM2903-N family is designed for single-supply operation over a wide operating-voltage range. TI identifies the device as a low-offset, dual differential comparator and specifies an offset voltage as low as 2.0 mV maximum for two comparators. The LM2903ITL/NOPB ordering option uses the compact 8-pin DSBGA (YZR) package, making it appropriate for space-constrained assemblies that can accommodate the package dimensions, ball pattern, and assembly process.
Typical uses include threshold detection, line-sensing, control-loop signaling, overvoltage and undervoltage indication, signal conditioning, and general dual-channel logic interfacing. In these applications, the comparator can translate a small analog difference into a stable logic-level event. The -40°C to +85°C temperature specification supports industrial and commercial equipment, although the final design must remain within all electrical limits and assembly constraints.
Design with the input common-mode range, supply voltage, output pull-up arrangement, input offset, response time, and logic thresholds as a complete system. Confirm the YZR package pin assignment and ball dimensions against the manufacturer datasheet before routing the PCB or beginning assembly. Choose pull-up voltage and resistor values from the connected logic interface rather than assuming the open-collector output supplies a fixed high level.
This product summary combines the exact ordering information, package description, operating-temperature range, comparator architecture, offset information, and response-time data needed to evaluate the LM2903ITL/NOPB. It also provides application guidance, practical interface considerations, and sourcing directions for comparing an existing design with other LM2903 ordering options.
جێگرەوەکانی جێگۆڕکێ بۆ LM2903ITL/NOPB — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2903ITL/NOPB (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparator Type, Number of Channels, Package.
LM2903-N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903ITL/NOPB زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Channel Independence | 2 independent comparators |
| Output Architecture | Open collector |
| Input Common-Mode Range | Rail-to-rail |
| Minimum Specified Offset Voltage | 2.0 mV maximum |
| Listed Maximum Offset Voltage | 15 mV maximum |
| Response Time | 1500 ns |
| Supply Architecture | Single supply |
| مەودای پلەی گەرمیی کارکردن | -40°C to +85°C |
| پاکێج | 8-pin DSBGA (YZR) |
| Package Type | Surface-mount DSBGA |
| جۆری دامەزراندن | Surface mount |
| Automotive Grade | Automotive grade |
ڕێنمایی ڕێکخستنی پینی LM2903ITL/NOPB surface-mount dsbga
ڕێکخستنی پین بۆ LM2903ITL/NOPB (پاکێجی surface-mount dsbga). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM2903ITL/NOPB.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM2903ITL/NOPB گونجاوە بۆ 6 بەکارھێنانs: Dual Voltage Threshold Detection, Industrial Sensor Signal Conditioning, Overvoltage and Undervoltage Indication, Open-Collector Logic Interfacing, Control-System Limit Detection, Battery and Portable-System Monitoring.
Dual Voltage Threshold Detection
The LM2903ITL/NOPB is suitable when a system must evaluate two independent analog thresholds. Each comparator channel compares its inverting and non-inverting inputs and provides an open-collector indication when the relationship between those voltages changes. Rail-to-rail input behavior is useful for signals near the lower or upper end of the device's operating range, while the family specification of offset as low as 2.0 mV maximum supports decisions involving relatively small voltage differences. The 8-pin DSBGA (YZR) package also helps reduce board area compared with most leaded dual comparators. Use suitable pull-up resistors on both outputs and define thresholds with precision resistors and stable reference sources.
Industrial Sensor Signal Conditioning
The LM2903ITL/NOPB can convert sensor-derived analog conditions into logic events for industrial monitoring equipment. Its two independent comparator channels allow one device to monitor separate upper and lower conditions, such as a control signal and a fault indication. The rail-to-rail input characteristic supports sensing near supply-rail thresholds, and the listed 1500 ns response time is appropriate for many monitoring and alarm functions rather than high-speed edge detection. Its -40°C to +85°C operating range suits broad commercial and industrial equipment. Design the sensor interface and threshold network to minimize noise, and use pull-up voltage levels that match the downstream controller.
Overvoltage and Undervoltage Indication
Use the two channels of the LM2903ITL/NOPB for complementary overvoltage and undervoltage indication in a compact power-control module. One channel can detect a signal above an upper reference, while the other detects a signal below a lower reference, producing open-collector fault indications for a controller or supervisor. The family's 2.0 mV maximum offset specification can improve comparison resolution around closely spaced thresholds. Accurate detection still depends on reference stability, input noise, resistor tolerance, and the timing of the upstream signal. Confirm the comparator's electrical limits from the manufacturer datasheet and keep the pull-up network short enough for the intended interface.
Open-Collector Logic Interfacing
The LM2903ITL/NOPB is appropriate when a logic system needs a flexible open-collector interface rather than a fixed push-pull output. Each output can be pulled up to the voltage expected by the receiving circuit, allowing interface-level adaptation without changing the comparator package. This is useful for alarm buses, wired supervisory signals, and systems with multiple open-collector nodes. The device includes two independent channels, so two interface functions can fit into one 8-pin DSBGA (YZR) package. Engineer the pull-up voltage and resistance together with bus capacitance, rise-time requirements, and fault behavior. Verify absolute output ratings against the selected pull-up rail before implementation.
Control-System Limit Detection
The LM2903ITL/NOPB can support limit detection in closed-loop industrial and equipment-control systems. Comparing a feedback voltage against a reference allows the comparator to flag an operating condition before the surrounding controller takes corrective action. Two channels allow simultaneous comparison of an upper and lower limit, or comparison of two separate control variables. Rail-to-rail inputs help when the feedback signal occupies a large portion of the supply range, and the open-collector output can directly drive an external pull-up network or fault input. For dependable control behavior, account for the listed 1500 ns response time, input offset, reference tolerance, and noise at the threshold. Keep sensitive feedback traces short and away from switching nodes.
Battery and Portable-System Monitoring
The LM2903ITL/NOPB can evaluate battery or portable-system rails when the board area is constrained and two comparator functions are needed. One channel may monitor a battery-related voltage while another checks a system signal, with open-collector outputs supporting pull-ups to the local logic rail. Its compact 8-pin DSBGA (YZR) package is useful in space-sensitive assemblies, and the -40°C to +85°C range covers many commercial and industrial portable designs. Battery monitoring accuracy depends on the threshold network, reference quality, and the comparator offset rather than package size alone. Review the datasheet for input and output limits, then design the pull-up network to prevent excessive discharge or back-powering.
داتای سەرچاوەی ئەندازیاری بۆ LM2903ITL/NOPB — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
Choose another LM2903 package option when its footprint is easier to assemble, when a leaded package better matches the product's interconnect density, or when its documented electrical limits provide a closer match to the target application. Consider another comparator family only after checking input range, output architecture, offset, response time, temperature rating, and qualification requirements.
Do not treat LM2903-N as a drop-in alternative because it denotes the family rather than a separate physical replacement. No verified cross-manufacturer YZR-footprint equivalent was established. A change to another package or manufacturer may therefore require PCB redesign, and any proposed substitute should be validated against both the system requirements and the manufacturer's current datasheet.
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin DSBGA (YZR) |
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 independent channels |
| Output Architecture | Open collector |
| Input Common-Mode Range | Rail-to-rail |
| — | 2.0 mV maximum |
| — | 15 mV maximum |
| Response Time | 1500 ns |
| Operating Temperature Range | -40°C to +85°C |
جیاکەرەوە سەرەکییەکان
- Two independent comparison channels in a compact package (بەراورد بەA single-channel comparator in a leaded package)
- Low-offset family specification (بەراورد بەA general-purpose comparator with a higher offset limit)
- Flexible open-collector output interface (بەراورد بەA fixed push-pull comparator output)
- Rail-to-rail comparison capability (بەراورد بەA comparator with a restricted common-mode input range)
تێبینییەکانی دیزاین
Do not treat the open-collector output as a source of the high logic level. Connect the required pull-up resistor from each output to the voltage expected by the receiving logic, and verify that this voltage remains within the comparator's allowable output conditions. Select the resistor using the required rise time, bus capacitance, input leakage, and available drive current. The 1500 ns listed response time applies to comparator operation, while pull-up resistance and load capacitance also influence the observed output transition.
Use the YZR package drawing and pin table from the manufacturer datasheet for the PCB land pattern, ball assignments, solder mask, and paste stencil. Confirm the orientation mark and all eight ball locations rather than inferring the arrangement from a generic BGA footprint. Route the two comparison channels separately when their inputs or thresholds are unrelated, keep sensitive inverting and non-inverting traces short, and maintain a continuous ground-reference path beneath the device to reduce noise coupling.
Set the switching threshold with stable components and account for input offset when the decision margin is small. The LM2903 family is specified with offset as low as 2.0 mV maximum for two comparators, but actual threshold uncertainty also includes reference accuracy, resistor tolerance, input noise, and temperature drift. If a clean logic transition is required, add hysteresis through positive feedback or a suitable feedback network and validate it against the intended threshold range.
Decouple the comparator supply near the package with a local bypass capacitor and route it using a short, low-impedance path to the ground reference. Keep the pull-up return current close to the comparator ground to prevent output transitions from injecting noise into the analog input network. Because this is a dual open-collector device, the pull-up rails and ground connections should be reviewed as part of the complete power-distribution design rather than treated as independent output accessories.
زانیاری پابەندبوون
The LM2903ITL/NOPB is identified as automotive grade and is rated for -40°C to +85°C. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer documentation.