LM339ADE4 - Quad Differential Comparator | Texas Instruments
MPN: LM339ADE4 ✓ چالاکLM339ADE4 گشتی
A differential comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference between them crosses a reference threshold. In the broader electronics hierarchy, the LM339 belongs to the comparator IC family, within linear integrated circuits and signal-conditioning systems. Its four channels allow one device to implement independent threshold detection, window comparison, zero-crossing detection, or level conversion without requiring four separate comparator packages.
The principal features of the LM339ADE4 include four open-collector outputs, supply-voltage operation from 2 V to 36 V, and low supply-current drain of 0.8 mA typical. The output structure is compatible with TTL, MOS, and CMOS logic, making the device useful where a comparator must drive a pull-up resistor, relay driver, indicator, or digital logic input. Differential input voltage can reach ±38 V, while the common-mode input range includes ground.
Internally, the LM339 uses four similar differential comparator sections operating from a common supply architecture. Because the outputs are open collector, each channel can sink logic-level current while remaining in a high-impedance state when inactive. An external pull-up resistor establishes the high output voltage. This architecture provides simple voltage translation and allows several open-collector outputs to share a bus when only one device is actively pulling the line low.
Typical uses include industrial control and sensor interfaces, battery-powered monitoring, motor and actuator threshold detection, window comparators, overvoltage and undervoltage protection, and logic-level translation. The ability to operate from a single supply is particularly useful in portable systems because the input common-mode range includes ground. The 14-pin SOIC package also supports conventional surface-mount PCB assembly.
Design the pull-up resistor for the required sink current, output rise time, bus capacitance, and available logic supply. Check input common-mode and absolute-maximum limits during startup because the input pins may briefly exceed the operating supply. Account for response delay when designing pulse-width or overvoltage systems; the typical 300 ns figure is a propagation-delay value rather than a guaranteed maximum.
This product record combines the manufacturer’s device information with package, pinout, application, and drop-in replacement guidance. It supports faster design decisions by distinguishing the LM339A electrical architecture from B-version and alternate-family options, while emphasizing where open-collector pull-ups, supply range, and input operating limits require engineering review.
جێگرەوەکانی جێگۆڕکێ بۆ LM339ADE4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM339ADE4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparator Type, Supply Voltage Range, Output Type, Package, Differential Input Voltage Range.
LM339BDE4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2901BDE4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM239DE4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2901DE4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM139DE4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM339ADE4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Differential comparator |
| Number of Channels | 4 channels |
| Propagation Delay | 300 ns typical |
| Supply Voltage Range | 2 V to 36 V |
| Differential Input Voltage Range | -38 V to +38 V |
| Common-Mode Input Range | Includes ground |
| جۆری دەرچوون | Open collector |
| Supply Current Drain | 0.8 mA typical |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
| Grade | Commercial grade |
| پاکێج | 14-pin SOIC |
| Package Width | 3.90 mm |
| جۆری دامەزراندن | Surface mount |
| ژمارەی پینەکان | 14 pins |
ڕێکخستنی پینی LM339ADE4
| پین 1 | OUT1 — Comparator 1 open-collector output |
| پین 2 | IN1− — Comparator 1 inverting input |
| پین 3 | IN1+ — Comparator 1 non-inverting input |
| پین 4 | GND — Ground connection |
| پین 5 | IN2+ — Comparator 2 non-inverting input |
| پین 6 | IN2− — Comparator 2 inverting input |
| پین 7 | OUT2 — Comparator 2 open-collector output |
| پین 8 | OUT3 — Comparator 3 open-collector output |
| پین 9 | IN3+ — Comparator 3 non-inverting input |
| پین 10 | IN3− — Comparator 3 inverting input |
| پین 11 | GND — Ground connection |
| پین 12 | IN4+ — Comparator 4 non-inverting input |
| پین 13 | IN4− — Comparator 4 inverting input |
| پین 14 | OUT4 — Comparator 4 open-collector output |
بەکارهێنانە باوەکان
LM339ADE4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Threshold Detection, Battery Overvoltage and Undervoltage Protection, Motor and Actuator Threshold Control, Window Comparator and Fault Detection, Portable Electronics and Battery Monitoring, Logic Level and Interface Translation.
Industrial Sensor Threshold Detection
The LM339ADE4 suits industrial sensor interfaces where a 4 V to 20 mA loop, resistive sensor, or divided supply must be compared with a precise threshold. Each of its four channels can detect a different limit without adding another comparator package. The 2 V to 36 V supply range accommodates varied industrial rails, while the common-mode input range includes ground for low-side sensing. Its 300 ns typical propagation delay is short enough for general process-limit detection, but the design should include hysteresis to prevent chatter around the threshold. Open-collector outputs can drive an optocoupler, relay driver, or PLC input through a suitable pull-up network.
پێشنیارکراو
Battery Overvoltage and Undervoltage Protection
The LM339ADE4 can monitor a battery-backed supply by comparing divided battery voltage against independent upper and lower reference thresholds. Two comparator channels provide undervoltage and overvoltage detection, while the remaining channels can supervise auxiliary rails. Its 2 V minimum operating supply supports low-energy systems, and the common-mode range including ground is useful when monitoring a rail near zero volts. The open-collector outputs allow wired-OR fault reporting through pull-up resistors. Designers should add positive feedback for hysteresis, verify that the divider remains inside the input common-mode limits, and account for the 300 ns typical propagation delay when coordinating protection timing.
پێشنیارکراو
Motor and Actuator Threshold Control
The LM339ADE4 can compare motor-position, current-sense, or actuator feedback signals and generate a control event when a defined limit is reached. Its four channels permit independent handling of start, stop, direction, and fault thresholds. The 300 ns typical response supports general control-loop assistance, although slower mechanical events usually require additional filtering rather than maximum timing speed. An open-collector output can directly sink current through a suitable driver interface or pull-up resistor, but it must not be assumed to source normal logic-high current. Keep sensing loops short, use a defined ground reference, and add noise filtering or hysteresis where motor transients could otherwise trigger repeated switching.
پێشنیارکراو
Window Comparator and Fault Detection
A window comparator built with the LM339ADE4 can flag a measured signal only when it lies below a lower limit or above an upper limit. Two channels can be wired against shared references, while the other channels monitor additional system variables. This arrangement is useful in power-quality, signal-integrity, and equipment-health monitoring systems. Because the device has a 300 ns typical propagation delay and open-collector outputs, it can support fast fault isolation without switching noise. Use separate pull-up resistors where each fault must remain independent, or a common pull-up for a wired-OR fault bus. Reference tolerance, input offset, resistor noise, and deliberate hysteresis should be considered together to prevent false fault indications.
پێشنیارکراو
Portable Electronics and Battery Monitoring
The LM339ADE4 is useful in portable and battery-powered equipment where four monitoring functions must fit in a compact surface-mount footprint. It can supervise a main battery, charger status signal, temperature-derived voltage, and accessory power rail using low supply-current operation of 0.8 mA typical. The common-mode input range includes ground, which simplifies detection near the bottom of a single-supply system. Open-collector outputs minimize the number of required active components and can wake a controller or drive a status indicator through a pull-up. Designers should calculate the complete divider current, avoid excessive quiescent loading, and use the device’s input and output limits for the device’s complete operating-temperature range.
پێشنیارکراو
Logic Level and Interface Translation
The LM339ADE4 can translate a lower-voltage or polarity-dependent logic signal into an open-collector event compatible with a higher-voltage digital system. Each output uses a pull-up resistor, allowing the high voltage to be selected independently from the comparator supply. The device’s TTL, MOS, and CMOS compatibility makes this arrangement useful for legacy industrial logic, relay inputs, and open-drain bus signaling. Use the non-inverting input as the logic-high reference and the inverting input as the signal input when an active-low output is required. Ensure the pull-up voltage remains within the output transistor’s absolute limits, and account for input offset, noise, and the 300 ns typical response delay when setting bus timing margins.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM339ADE4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM339BDE4 | LM2901BDE4 | LM239DE4 | LM2901DE4 | LM139DE4 |
|---|---|---|---|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
جیاکەرەوە سەرەکییەکان
- Four independent channels in one 14-pin package (بەراورد بەLM2901BDE4)
- Defined 300 ns typical response specification (بەراورد بەLM239DE4)
- Single and dual supply operation with ground-inclusive common mode (بەراورد بەLM139DE4)
تێبینییەکانی دیزاین
Treat each open-collector output as a current-sinking output and calculate its pull-up resistor from the target high voltage, required sink current, and acceptable rise time. The comparator supply and pull-up supply may be different, but the output-pin absolute limits must be respected. Avoid selecting an excessively small resistance because the output would be forced to sink more current than intended; avoid an excessively large value when the attached logic requires a fast rising edge.
Do not assume that a differential input may be arbitrarily large during fault conditions. The LM339ADE4 supports differential input voltage up to ±38 V, while normal operation also depends on the common-mode range and supply state. Use input series resistance or clamps where transients can exceed the limits. In single-supply systems, keep both inputs within the valid common-mode range and design the threshold divider so that no input floats during power-up.
Add positive feedback to create hysteresis when the compared signal can cross the threshold slowly or contain noise. The required feedback resistance depends on the divider impedance and input offset of the installation. Keep comparator input traces away from switching nodes and relay-drive traces, use a compact ground reference for the sensing circuit, and place any input filtering capacitors where their charging behavior does not distort the intended detection delay.
زانیاری پابەندبوون
The manufacturer identifies LM339A as a commercial-grade quad differential comparator. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the DE4 ordering code require confirmation from the current manufacturer documentation.